The specific heat capacity of electrons found using quantum models is less than that found using classical models because of the difference in the way electrons are modeled by the two theories.
According to classical models, electrons are treated as tiny, indivisible, and point-like particles that move around in a fixed orbit around the nucleus. This means that the electrons are considered to be in constant motion, and they are not subject to any forces that can change their energy level.
On the other hand, in quantum mechanics, electrons are treated as wave-like entities that can exist in a superposition of states. This means that electrons are subject to the laws of wave mechanics and are subject to quantization. This means that the electrons can only exist in specific energy levels, and they can only gain or lose energy in specific amounts known as quanta.
This means that the specific heat capacity of electrons found using quantum models is less than that found using classical models because the energy levels of the electrons are quantized. This means that the electrons can only absorb or release energy in specific amounts, and this restricts the number of energy states that the electrons can occupy. As a result, the amount of energy required to raise the temperature of the electrons is less than that predicted by classical models.
Let's learn more about specific heat capacity:
https://brainly.com/question/27991746
#SPJ11
Calculate how many times you can travel around the earth using 1.228x10^2GJ with an E-scooter which uses 3 kWh per 100 km. Note that you can travel to the sun and back with this scooter using the energy of a whole year.
Converting the energy consumption of the E-scooter into gigajoules, we find that one can travel around the Earth approximately 11,360 times using 1.228x10^2 GJ of energy with the E-scooter.
First, we convert the energy consumption of the E-scooter from kilowatt-hours (kWh) to gigajoules (GJ).
1 kilowatt-hour (kWh) = 3.6 megajoules (MJ)
1 gigajoule (GJ) = 1,000,000 megajoules (MJ)
So, the energy consumption of the E-scooter per 100 km is:
3 kWh * 3.6 MJ/kWh = 10.8 MJ (megajoules)
Now, we calculate the number of trips around the Earth.
The Earth's circumference is approximately 40,075 kilometers.
Energy consumed per trip = 10.8 MJ
Total energy available = 1.228x10^2 GJ = 1.228x10^5 MJ
Number of trips around the Earth = Total energy available / Energy consumed per trip
= (1.228x10^5 MJ) / (10.8 MJ)
= 1.136x10^4
Therefore, approximately 11,360 times one can travel around the Earth using 1.228x10^2 GJ of energy with the E-scooter.
To know more about energy consumption, refer to the link :
https://brainly.com/question/30125850#
#SPJ11
An ideal neon sign transformer provides 9080 V at 51.0 mA with an input voltage of 110 V. Calculate the transformer's
input power and current.
An ideal neon sign transformer provides 9080 V at 51.0 mA with an input voltage of 110 V, the transformer's input power is approximately 464.28 W and the input current is approximately 4.22 A.
We can use the following calculation to compute the transformer's input power:
Input Power (P) = Input Voltage (V) * Input Current (I)
Here, it is given that:
Input Voltage (V) = 110 V
Input Current (I) = ?
Input Current (I) = Output Power (P) / Output Voltage (V)
Given:
Output Power (P) = 9080 V * 51.0 mA = 464.28 W (converting mA to A)
Output Voltage (V) = 9080 V
Now,
Input Current (I) = 464.28 W / 110 V ≈ 4.22 A
Thus, the transformer's input power is approximately 464.28 W and the input current is approximately 4.22 A.
For more details regarding transformer, visit:
https://brainly.com/question/15200241
#SPJ4
An unknown metal "X" is used to make a 5.0 kg container that is then used to hold 15 kg of water. Both the container and the water have an initial temperature of 25 °C. A 3.0 kg piece of the metal "X" is heated to 300 °C and dropped into the water. If the final temperature of the entire system is 30 °C when thermal equilibrium is reached, determine the specific heat of the mystery metal.
The specific heat of the unknown metal "X" is approximately 0.50 J/g°C, indicating its ability to store and release thermal energy.
To find the specific heat of the metal, we can use the equation Q = mcΔT, where Q represents the heat transferred, m is the mass, c is the specific heat, and ΔT is the change in temperature. In this case, the heat gained by the water is equal to the heat lost by the metal and the container.
We can calculate the heat gained by the water using Qwater = mwatercwaterΔT, where m water is the mass of water, cwater is the specific heat of water, and ΔT is the change in temperature. The heat lost by the metal and the container is given by Qmetal = (mmetal + mcontainer)cmetalΔT. By equating Qwater and Qmetal, we can solve for the specific heat of the metal, cm.
Substituting the given values, we have:
(mmetal + mcontainer)cmetalΔT = mwatercwaterΔT
Simplifying, we get:
(3.0 kg + 5.0 kg)cmetal(30 °C - 300 °C) = 15 kg(4.18 J/g°C)(30 °C - 25 °C)
Solving the equation, we find the value of cm to be:
cmetal ≈ 0.50 J/g°C
Therefore, the specific heat of the unknown metal "X" is approximately 0.50 J/g°C.
To learn more about specific heat click here:
brainly.com/question/31608647
#SPJ11
A 380 kg piano is pushed at constant speed a distance of 3.9 m up a 27° incline by a mover who is pushing parallel to the incline. The coefficient of friction between the piano & ramp is 0.45. (a) De
The force exerted by the mover must balance the forces of gravity and friction.
The work done by the mover would be the force exerted by the mover multiplied by the distance the piano is pushed up the incline.
The piano is being pushed at a constant speed and there is no change in vertical position, the work done by the force of gravity is zero.
(a) To determine the force exerted by the mover, we need to consider the forces acting on the piano. These forces include the force of gravity, the normal force, the force exerted by the mover, and the frictional force. By analyzing the forces, we can find the force exerted by the mover parallel to the incline.
The force exerted by the mover must balance the forces of gravity and friction, as well as provide the necessary force to push the piano up the incline at a constant speed.
(b) The work done by the mover is calculated using the formula
W = F * d, where
W is the work done,
F is the force exerted by the mover
d is the distance moved.
In this case, the work done by the mover would be the force exerted by the mover multiplied by the distance the piano is pushed up the incline.
(c) The work done by the force of gravity can be calculated as the product of the force of gravity and the distance moved vertically. Since the piano is being pushed at a constant speed and there is no change in vertical position, the work done by the force of gravity is zero.
By considering the forces, work formulas, and the given values, we can determine the force exerted by the mover, the work done by the mover, and the work done by the force of gravity in pushing the piano up the incline.
Complete Question-
A 380 kg piano is pushed at constant speed a distance of 3.9 m up a 27° incline by a mover who is pushing parallel to the incline. The coefficient of friction between the piano & ramp is 0.45. (a) Determine the force exerted by the man (include an FBD for the piano): (b) Determine the work done by the man: (c) Determine the work done by the force of gravity
To know more about gravity , click here-
brainly.com/question/31321801
#SPJ11
Determine the number of moles of oxygen gas in the following
container.
The container holds 2.90 m3 at 17.84oF and
an a gauge pressure of 16.63kPa.
The number of moles of oxygen gas in the container is determined by the ideal gas law, using the given volume, temperature, and pressure 0.993 moles.
To determine the number of moles of oxygen gas in the container, we can use the ideal gas law, which states that PV = nRT, where P is the pressure, V is the volume, n is the number of moles, R is the ideal gas constant, and T is the temperature in Kelvin.
First, let's convert the given temperature from Fahrenheit to Kelvin:
T(K) = (T(°F) + 459.67) × (5/9)
T(K) = (17.84 + 459.67) × (5/9)
T(K) ≈ 259.46 K
Next, we convert the given pressure from kilopascals (kPa) to pascals (Pa):
P(Pa) = P(kPa) × 1000
P(Pa) = 16.63 kPa × 1000
P(Pa) = 16630 Pa
Now, we can rearrange the ideal gas law equation to solve for n (number of moles):
n = PV / RT
Substituting the known values:
n = (16630 Pa) × (2.90 m³) / ((8.314 J/(mol·K)) × (259.46 K))
Simplifying the equation:
n ≈ 0.993 moles
Therefore, the number of moles of oxygen gas in the container is approximately 0.993 moles.
To learn more about moles click here:
brainly.com/question/15209553
#SPJ11
c).i. A conductor transfers heat of 3000 J across its length of 20cm in 6 seconds. Given that its cross-sectional area A is 55cm². Determine the thermal conductivity of the material if the temperature difference across the ends is 67°C? ii. An object of emissivity 0.7 and cross-sectional area 55mm? at room temperature of 30° losses energy at a rate of 35.6 J/s. What is the initial 2 2/7 temperature of the object? [ hint; stefan's constant o = 5.6703 x10- 8W/m/K+ ]
The thermal conductivity of the material is 0.238 W/m°C and the initial temperature of the object is 209°C.
i. Length of the conductor, L = 20 cm = 0.2 m
Time taken, t = 6 s
Cross-sectional area, A = 55 cm² = 55 × 10⁻⁴ m²
Heat transferred, Q = 3000 J
Temperature difference, ΔT = 67°C
Thermal conductivity of the material, K = ?
Formula used: Heat transferred, Q = K × A × ΔT ÷ L
where Q is the heat transferred, K is the thermal conductivity of the material, A is the cross-sectional area, ΔT is the temperature difference and L is the length of the conductor.
So, K = Q × L ÷ A × ΔT
Substituting the given values, we get,
K = 3000 J × 0.2 m ÷ (55 × 10⁻⁴ m²) × 67°C
K = 0.238 W/m°C
ii. Area of the object, A = 55 mm²
= 55 × 10⁻⁶ m²
Emissivity of the object, ε = 0.7
Rate of energy loss, P = 35.6 J/s
Stefan's constant, σ = 5.6703 × 10⁻⁸ W/m²/K⁴
Initial temperature, T₁ = ?
Formula used: Rate of energy loss, P = ε × σ × A × (T₁⁴ - T₂⁴)
where P is the rate of energy loss, ε is the emissivity of the object, σ is the Stefan's constant, A is the area of the object, T₁ is the initial temperature and T₂ is the final temperature.
So, P = ε × σ × A × (T₁⁴ - T₂⁴)
Solving the above equation for T₁, we get
T₁⁴ - T₂⁴ = P ÷ (ε × σ × A)
T₁⁴ = (P ÷ (ε × σ × A)) + T₂
⁴T₁ = [ (P ÷ (ε × σ × A)) + T₂⁴ ]¹∕⁴
Substituting the given values, we get,
T₁ = [ (35.6 J/s) ÷ (0.7 × 5.6703 × 10⁻⁸ W/m²/K⁴ × 55 × 10⁻⁶ m²) + (30 + 273)⁴ ]¹∕⁴
T₁ = 481.69 K
≈ 208.69°C
≈ 209°C (approx.)
Therefore, the thermal conductivity of the material is 0.238 W/m°C and the initial temperature of the object is 209°C.
To know more about thermal conductivity, visit:
https://brainly.com/question/14553214
#SPJ11
The magnetic force F' is always perpendicular to the acceleration a of the particle. T/F
True, the magnetic force F' is always perpendicular to the acceleration a of the particle.
True. According to the Lorentz force law, the magnetic force F' experienced by a charged particle moving in a magnetic field is given by F' = q(v × B), where q is the charge of the particle, v is its velocity, and B is the magnetic field.
Since the cross product v × B results in a vector perpendicular to both v and B, the magnetic force F' is always perpendicular to the velocity of the particle. Additionally, Newton's second law states that F' = ma, where m is the mass of the particle and a is its acceleration. Therefore, the magnetic force F' is always perpendicular to the acceleration a of the particle.
To learn more about magnetic field
Click here brainly.com/question/14848188
#SPJ11
How far apart (m) will two charges, each of magnitude 14 μC, be
a force of 0.80 N on each other? Give your answer to two decimal
places.
Two charges of magnitude 14 μC will be 4.00 m apart if the force of attraction between them is 0.80 N. This is the required answer. TCoulomb's Law describes the electrostatic interaction between charged particles.
This law states that the force of attraction or repulsion between two charged particles is directly proportional to the product of the charges and inversely proportional to the square of the distance between them. The formula for Coulomb's law is:F = kQ1Q2/d²where F is the force between two charges, Q1 and Q2 are the magnitudes of the charges, d is the distance between the two charges, and k is the Coulomb's constant.
Electric charges are the fundamental properties of matter. There are two types of electric charges: positive and negative. Like charges repel each other, and opposite charges attract each other. Electric charges can be transferred from one object to another, which is the basis of many electrical phenomena such as lightning and electric circuits. The unit of electric charge is the coulomb (C).
To know more about repel visit:
https://brainly.com/question/15744700
#SPJ11
P1 = P0 + rho g h1
Where
P0 = weight of air at sea level = 1.01 X 105
Pa
rho = m/V Density
= mass/volume
F1/A1=F2/A2
The force on a surface area of 2 m^2 is 200 N.
The equation P1 = P0 + rho g h1 is used to calculate the pressure at a height h1 above sea level, where P0 is the pressure at sea level, rho is the density of air, g is the acceleration due to gravity, and h1 is the height above sea level.
The equation F1/A1=F2/A2 is used to calculate the force on a surface area A1 due to a force F1, where F2 is the force on a surface area A2.
Here is an example of how to use these equations:
Suppose we want to calculate the pressure at a height of 1000 meters above sea level. We know that the pressure at sea level is 1.01 x 10^5 Pa, the density of air is 1.225 kg/m^3, and the acceleration due to gravity is 9.81 m/s^2. We can use the equation P1 = P0 + rho g h1 to calculate the pressure at a height of 1000 meters:
P1 = 1.01 x 10^5 Pa + 1.225 kg/m^3 * 9.81 m/s^2 * 1000 m = 113017.25 Pa
Therefore, the pressure at a height of 1000 meters above sea level is 113017.25 Pa.
Here is another example of how to use these equations:
Suppose we have a surface area of 1 m^2 and a force of 100 N acting on it. We can use the equation F1/A1=F2/A2 to calculate the force on a surface area of 2 m^2:
F2 = F1 * A2/A1 = 100 N * 2 m^2 / 1 m^2 = 200 N
Therefore, the force on a surface area of 2 m^2 is 200 N.
Learn more about surface area with the given link,
https://brainly.com/question/16519513
#SPJ11
An electron is shot vertically upward through the tiny holes in the center of a parallel-plate capacitor. If the initial speed of the electron at the hole in the bottom plate of the capacitor is 4.00
Given Data: The initial speed of the electron at the hole in the bottom plate of the capacitor is 4.00.What is the final kinetic energy of the electron when it reaches the top plate of the capacitor? Explanation: The potential energy of the electron is given by, PE = q V Where q is the charge of the electron.
V is the potential difference across the capacitor. As the potential difference across the capacitor is constant, the potential energy of the electron will be converted to kinetic energy as the electron moves from the bottom to the top of the capacitor. Thus, the final kinetic energy of the electron is equal to the initial potential energy of the electron. K.E = P.E = qV Thus, K.E = eV Where e is the charge of the electron. K.E = 1.60 × 10-19 × 1000 × 5K.E = 8 × 10-16 Joule, the final kinetic energy of the electron when it reaches the top plate of the capacitor is 8 × 10-16 Joule.
To know more about energy visit:
https://brainly.com/question/1932868
#SPJ11
A particle with a charge of −1.24×10 −8 C is moving with Part A instantaneous velocity v =(4.19×10 4 m/s) i ^ +(−3.85×10 4 m/s) j ^ What is the force exerted on this particle by a magnetic field B =(2.80 T) i ^ ? Express the x,y, and z components of the force in newtons separated by commas Part B What is the force exerted on this particle by a magnetic field B =(2.80 T) k ^ ? Express the x,y, and z components of the force in newtons separated by commas
Thus, the force components are:
Part A: 0 N, 0 N, -1.71×[tex]10^{-3}[/tex] N
Part B: -1.71×[tex]10^{-3}[/tex] N, 0 N, 0 N
To calculate the force exerted on the particle by a magnetic field, we can use the equation:
F = q * (v x B)
where F is the force, q is the charge, v is the velocity vector, and B is the magnetic field vector.
Given:
Charge (q) = -1.24×[tex]10^{-8}[/tex]C
Velocity (v) = (4.19×[tex]10^4[/tex] m/s) i^ + (-3.85×[tex]10^4[/tex] m/s) j^
Magnetic Field (B) = (2.80 T) i^
Part A:
To find the force components in the x and y directions, we can substitute the given values into the equation:
F = (-1.24×[tex]10^{-8}[/tex] C) * ((4.19×[tex]10^4[/tex]m/s) i^ + (-3.85×[tex]10^4[/tex] m/s) j^) x (2.80 T) i^
Expanding and simplifying, we get:
F = (-1.24×[tex]10^{-8}[/tex]C) * (4.19×[tex]10^4[/tex]m/s) * (2.80 T) k^
The force in the x, y, and z components is given by:
Fx = 0 N
Fy = 0 N
Fz = (-1.24×[tex]10^{-8}[/tex]C) * (4.19×[tex]10^4[/tex] m/s) * (2.80 T) = -1.71×[tex]10^{-3 }[/tex] N
Part B:
In this case, the magnetic field is in the z-direction (k^). Therefore, the force components in the x, y, and z directions are:
Fx = (-1.24×[tex]10^{-8}[/tex]C) * (4.19×[tex]10^4[/tex] m/s) * (2.80 T) = -1.71×[tex]10^{-3 }[/tex]N
Fy = 0 N
Fz = 0 N
Thus, the force components are:
Part A: 0 N, 0 N, -1.71×[tex]10^{-3 }[/tex] N
Part B: -1.71×[tex]10^{-3 }[/tex] N, 0 N, 0 N
Learn more about force, here:
https://brainly.com/question/30507236
#SPJ4
3. AIS MVX, 6.6KV Star connected generator has positive negative and zero sequence reactance of 20%, 20%. and 10. respect vely. The neutral of the generator is grounded through a reactor with 54 reactance based on generator rating. A line to line fault occurs at the terminals of the generator when it is operating at rated voltage. Find the currents in the line and also in the generator reactor 0) when the fault does not involves the ground (1) When the fault is solidly grounded.
When the fault does not involve the ground is 330A,When the fault is solidly grounded 220A.
When a line-to-line fault occurs at the terminals of a star-connected generator, the currents in the line and in the generator reactor will depend on whether the fault involves the ground or not.
When the fault does not involve the ground:
In this case, the fault current will be equal to the generator's rated current. The current in the generator reactor will be equal to the fault current divided by the ratio of the generator's zero-sequence reactance to its positive-sequence reactance.
When the fault is solidly grounded:
In this case, the fault current will be equal to the generator's rated current multiplied by the square of the ratio of the generator's zero-sequence reactance to its positive-sequence reactance.
The current in the generator reactor will be zero.
Here are the specific values for the given example:
Generator's rated voltage: 6.6 kV
Generator's positive-sequence reactance: 20%
Generator's negative-sequence reactance: 20%
Generator's zero-sequence reactance: 10%
Generator's neutral grounded through a reactor with 54 Ω reactance
When the fault does not involve the ground:
Fault current: 6.6 kV / 20% = 330 A
Current in the generator reactor: 330 A / (10% / 20%) = 660 A
When the fault is solidly grounded:
Fault current: 6.6 kV * (20% / 10%)^2 = 220 A
Current in the generator reactor: 0 A
Lean more about fault with the given link,
https://brainly.com/question/3088
#SPJ11
A disk starts from rest and takes 3.0 s to reach 2,000 rpm. Assume that the disk rotates with constant angular acceleration and that its moment of inertia is 2.5 x 10-5 kg m². Determine the torque applied to the disk.
Assuming that the disk rotates with constant angular acceleration and that its moment of inertia is 2.5 x 10-5 kg m².The torque applied to the disk is 0.0825 Nm.
We are given that the disk starts from rest and reaches a rotational speed of 2,000 rpm in 3.0 seconds. We can convert this angular velocity to radians per second by multiplying it by [tex]\frac{2\pi }{60}[/tex] since there are 2π radians in one revolution and 60 seconds in a minute. Thus, the final angular velocity (ω) of the disk is (2000 * [tex]\frac{2\pi }{60}[/tex]) = 209.44 rad/s.
To determine the torque applied to the disk, we can use the equation τ = Iα, where τ represents torque, I is the moment of inertia, and α is the angular acceleration.
Since the disk starts from rest, the initial angular velocity (ω₀) is 0. We can calculate the angular acceleration (α) using the equation α = (ω - ω₀) / t, where t is the time interval. Substituting the given values, we have α = [tex]\frac{(209.44 - 0)}{3.0}[/tex] = 69.813 rad/s².
Now we can calculate the torque by rearranging the equation τ = Iα to τ = (2.5 x 10⁻⁵ kg m²) × (69.813 rad/s²) = 0.0825 Nm. Therefore, the torque applied to the disk is 0.0825 Nm.
Learn more about velocity here:
https://brainly.com/question/30559316
#SPJ11
One mole of an ideal gas is held at a constant pressure of 1 atm. Find the change in volume (in liters) if the temperature changes by 62°C.
The change in volume of one mole of an ideal gas held at a constant pressure of 1 atm if the temperature changes by 62°C is 2.4 liters.
The ideal gas law states that PV = nRT, where P is the pressure, V is the volume, n is the number of moles of gas, R is the ideal gas constant, and T is the temperature in Kelvin.
If we rearrange the equation to solve for V, we get V = nRT/P.
In this problem,
we are given that P = 1 atm, n = 1 mole,
and T changes from 273 K (0°C) to 335 K (62°C).
Plugging these values into the equation,
we get V = (1 mol)(8.314 J/mol K)(335 K)/1 atm = 2.4 liters.
Therefore, the change in volume is 2.4 liters. This means that the volume of the gas will increase by 2.4 liters if the temperature is increased by 62°C.
To learn more about ideal gas here brainly.com/question/26088764
#SPJ11
2. On the Season Finale of Keeping Up With The Gretta Bears: Gretta decides that she wants to go skiing in Aspen. When she gets there, she decides that snow is cold, her legs are short, and that skiing is so last year. With no need for her 10-kg skis anymore, she pushes them away at a speed of 12-m/s. The skis collide with 20-kg Buster and catch in his leash. Buster and the skis proceed to slide down a 30° slope of length 100-m. At the bottom of the slope, Buster is caught by a net attached to a spring with an effective spring constant of 500N/m. How far does the spring stretch before Buster momentarily comes to rest?
The spring stretches to 1.69 meters before Buster momentarily comes to rest.
How do we calculate?We find the initial kinetic energy of the skis before they collide with Buster:
Kinetic energy of skis = (1/2) * mass * velocity²
= (1/2) * 10 kg * (12 m/s)²
= 720 J
Change in height = height * sin(angle)
= 100 m * sin(30°)
= 50 m
The total initial gravitational potential energy is equal to the kinetic energy of the skis, since that Buster starts from rest = Initial potential energy = 720 J
The potential energy stored in the stretched spring :
= (1/2) * k * x²
720 J = (1/2) * 500 N/m * x²
1440 J = 500 N/m * x²
x² = (1440 J) / (500 N/m)
x² = 2.88 m
x = 1.69 m
Learn more about potential energy at:
https://brainly.com/question/14427111
#SPJ4
Radios use resonance in order to tune-in to a particular station. A physics student builds a simple radio using a RLC series circuit. They decide to use a resistor with R=49.5Ω, but they only have one capacitor with capacitance C=180pF. To listen to their favorite station KXY 84.8 FM, which is at a frequency of 84.8MHz, what must be the inductance L of their circuit's inductor? L
The inductance (L) of the circuit's inductor must be approximately 120 μH.
In order to tune in to a specific radio station, resonance is utilized in radios. Resonance occurs when the frequency of the radio station matches the natural frequency of the radio circuit. To achieve resonance in a series RLC circuit, the inductive reactance (XL) and the capacitive reactance (XC) should be equal, canceling each other out. The inductive reactance is given by XL = 2πfL, where f is the frequency and L is the inductance of the inductor.
To listen to station KXY 84.8 FM with a frequency of 84.8 MHz (84.8 × 10^6 Hz), we need to determine the inductance (L). First, we need to calculate the capacitive reactance (XC). XC is given by XC = 1 / (2πfC), where C is the capacitance of the capacitor.
Plugging in the values, we have XC = 1 / (2π × 84.8 × 10^6 Hz × 180 × 10^(-12) F). By simplifying this expression, we can find the value of XC.
Once we have the value of XC, we can set it equal to XL and solve for L. Since XC = XL, we can write 1 / (2πfC) = 2πfL. Rearranging this equation and substituting the given values, we can solve for L.
Following these calculations, we find that the inductance (L) of the circuit's inductor must be approximately 120 μH to tune in to station KXY 84.8 FM.
Learn more about circuit's
brainly.com/question/12608491
#SPJ11
A
car is traveling at 20 m/s. When the driver steps harder on the gas
pedal it causes the car to accelerate at 2 m/s^2. How far, in
meters, has the car travled in 3 seconds?
The car would have travelled 69 meters in 3 seconds.
When a car is travelling at 20 m/s and the driver steps harder on the gas pedal, causing the car to accelerate at 2 m/s², the distance the car would have travelled in 3 seconds is given by:
S = ut + 1/2 at²
Where u = initial velocity
= 20 m/s
a = acceleration
= 2 m/s²
t = time taken
= 3 seconds
Substituting these values, we get:
S = 20(3) + 1/2(2)(3)²
S = 60 + 9
S = 69 meters
Therefore, the car would have travelled 69 meters in 3 seconds.
Learn more about meters from the given link
https://brainly.com/question/1578784
#SPJ11
An object of mass 4.20 kg is projected into the air at a 55.0° angle. It hits the ground 3.40 s later. Set "up" to be the positive y direction. What is the y-component of the object's change in momentum while it is in the air? Ignore air resistance.
The y-component of the object's change in momentum while it is in the air is -139.944 Kg.m/s
How do i determine the y-component of change in momentum?First, we shall obtain the initial velocity. Details below:
Angle of projection (θ) = 55 ° Acceleration due to gravity (g) = 9.8 m/s²Time of flight (T) = 3.40Initial velocity (u) = ?T = 2uSineθ / g
3.40 = (2 × u × Sine 55) / 9.8
Cross multiply
2 × u × Sine 55 = 3.4 × 9.8
Divide both sides by (2 × Sine 55)
u = (3.4 × 9.8) / (2 × Sine 55)
= 20.34 m/s
Next, we shall obtain the initial and final velocity in the y-component direction. Details below:
For initial y-component:
Initial velocity (u) = 20.34 m/sAngle of projection (θ) = 55 °Initial y-component of velocity (uᵧ) =?uᵧ = u × Sine θ
= 20.34 × Sine 55
= 16.66 m/s
For final y-component:
Initial y-component of velocity (uᵧ) = 16.66 m/sAcceleration due to gravity (g) = 9.8 m/s²Time (t) = 3.4 sFinal y-component of velocity (vᵧ) =?vᵧ = uᵧ - gt
= 16.66 - (9.8 × 3.4)
= -16.66 m/s
Finally, we shall obtain the change in momentum. This is shown below:
Mass of object (m) = 4.20 KgInitial velocity (uᵧ) = 16.66 m/sFinal velocity (vᵧ) = -16.66Change in momentum =?Change in momentum = m(vᵧ - uᵧ)
= 4.2 × (-16.66 - 6.66)
= 4.2 × -33.32
= -139.944 Kg.m/s
Learn more about change in momentum:
https://brainly.com/question/21297884
#SPJ4
can
i please get the answer to this
Question 7 (1 point) Standing waves Doppler shift Resonant Frequency Resonance Constructive interference Destructive interference
Standing waves, Doppler shift, resonant frequency, resonance, constructive interference, and destructive interference are all concepts related to wave phenomena.
Standing waves refer to a pattern of oscillation in which certain points, called nodes, do not move while others, called antinodes, oscillate with maximum amplitude. They are formed by the interference of two waves with the same frequency and amplitude traveling in opposite directions. Doppler shift occurs when there is a change in frequency or wavelength of a wave due to the relative motion between the source of the wave and the observer. It is commonly observed with sound waves, where the frequency appears higher as the source moves towards the observer and lower as the source moves away.
Resonant frequency refers to the natural frequency at which an object vibrates with maximum amplitude. When an external force is applied at the resonant frequency, resonance occurs, resulting in a large amplitude response. This phenomenon is commonly used in musical instruments, such as strings or air columns, to produce sound.
Constructive interference happens when two or more waves combine to form a wave with a larger amplitude. In this case, the waves are in phase and reinforce each other. Destructive interference occurs when two or more waves combine to form a wave with a smaller amplitude or cancel each other out completely. This happens when the waves are out of phase and their crests align with the troughs.These concepts play crucial roles in understanding and analyzing various wave phenomena, including sound, light, and electromagnetic waves.
To learn more about Doppler shift click here : brainly.com/question/28106478
#SPJ11
What is the weight of a 156O−kg car?
The weight of a 1560 kg car is approximately 15,317 Newtons (N). Weight is a measure of the force of gravity acting on an object, and it is calculated by multiplying the mass of the object by the acceleration due to gravity.
In this case, the mass of the car is 1560 kg. The standard acceleration due to gravity on Earth is approximately 9.8 m/s². By multiplying the mass (1560 kg) by the acceleration due to gravity (9.8 m/s²), we find that the weight of the car is approximately 15,317 N.
The weight of an object is directly proportional to its mass and the acceleration due to gravity. In this case, the mass of the car is given as 1560 kg. The acceleration due to gravity is a constant value on Earth, approximately 9.8 m/s².
To calculate the weight, we multiply the mass (1560 kg) by the acceleration due to gravity (9.8 m/s²). This yields a weight of approximately 15,317 N. Weight is a force, and it is measured in Newtons (N). Therefore, a 1560 kg car would weigh approximately 15,317 N on Earth.
Learn more about gravity click here:
brainly.com/question/31321801
#SPJ11
A 5nC charge is located at (0,7)cm and another 2nC charge is located at (−3,0)cm. What would be the magnitude of the net electric field at the origin (0,0)cm ?
The magnitude of the net electric field at the origin (0,0) cm is approximately [tex]83.19 × 10^6 N/C[/tex].
To calculate the magnitude of the net electric field at the origin, we need to calculate the electric fields generated by each charge and then sum them up.
The electric field at a point due to a point charge is given by Coulomb's Law:
E = k * (q / [tex]r^2[/tex])
where E is the electric field, k is the electrostatic constant ([tex]9 × 10^9 Nm^2/C^2[/tex]), q is the charge, and r is the distance from the charge to the point.
Let's calculate the electric fields generated by each charge at the origin:
For the 5nC charge:
q1 = 5nC
r1 = 7 cm = 0.07 m
E1 = k * (q1 / [tex]r1^2[/tex])
For the 2nC charge:
q2 = 2nC
r2 = 3 cm = 0.03 m
E2 = k * (q2 / [tex]r2^2[/tex])
Now, we can calculate the net electric field by summing up the electric fields:
E_net = E1 + E2
Substituting the values and performing the calculations:
[tex]E1 = (9 × 10^9 Nm^2/C^2) * (5 × 10^(-9) C) / (0.07 m)^2[/tex]
E1 ≈ 9188571.43 N/C
[tex]E2 = (9 × 10^9 Nm^2/C^2) * (2 × 10^(-9) C) / (0.03 m)^2[/tex]
E2 ≈ 74000000 N/C
E_net = E1 + E2
E_net ≈ 83188571.43 N/C
To know more about electric field refer to-
https://brainly.com/question/11482745
#SPJ11
Green light has a wavelength of 5.20 × 10−7 m and travels through the air at a speed of 3.00 × 108 m/s.
Calculate the frequency of green light waves with this wavelength. Answer in units of Hz.
Calculate the period of green light waves with this wavelength. Answer in units of s.
To calculate the frequency of green light waves with a wavelength of 5.20 × 10^(-7) m, we can use the formula: Frequency (f) = Speed of light (c) / Wavelength (λ). Therefore, the period of green light waves with a wavelength of 5.20 × 10^(-7) m is approximately 1.73 × 10^(-15) s.
Plugging in the values:
Frequency = 3.00 × 10^8 m/s / 5.20 × 10^(-7) m
Frequency ≈ 5.77 × 10^14 Hz
Therefore, the frequency of green light waves with a wavelength of 5.20 × 10^(-7) m is approximately 5.77 × 10^14 Hz.
To calculate the period of green light waves with this wavelength, we can use the formula:
Period (T) = 1 / Frequency (f)
Plugging in the value of frequency:
Period = 1 / 5.77 × 10^14 Hz
Period ≈ 1.73 × 10^(-15) s
Therefore, the period of green light waves with a wavelength of 5.20 × 10^(-7) m is approximately 1.73 × 10^(-15) s.
To learn more about, frequency, click here, https://brainly.com/question/2140860
#SPJ11
A cat with mass mk = 5.00 kg sits on a swing that has mass mh = 1.50 kg. Ignore the mass of the ropes that hold the swing up. Suddenly a dog appears, and the cat jumps down from the swing to hide. As the cat jumps off, the swing swings backwards. Assume that the cat jumps out horizontally and that both the cat and the swing are particles. Ignore all forms of friction. - Find the speed of the cat as it leaves the swing when you know that the height h = 0.545 m and that the horizontal distance s = 0.62 m. - Use the result above to find out how high above its lowest point the swing can get. If you have not solved the part, you can set up and justify the equations that must be used. = = -
The speed of the cat as it leaves the swing when you know that the height h = 0.545 m and that the horizontal distance s = 0.62 m is 2.866 m/s and the maximum height is 0.419 m.
Speed of the cat as it leaves the swing:
To find the speed of the cat, we can use the principle of conservation of mechanical energy. Initially, the system (cat + swing) has gravitational potential energy, which is converted into kinetic energy as the cat jumps off the swing.
Using the conservation of mechanical energy equation:
[tex]m_k gh=0.5(m_k+m_h)v^{2} \\5 \times 9.8 \times 0.545=0.5(5.00+1.50)v^{2} \\26.705=3.25 v^{2}\\\8.2169=v^{2}\\ v=\sqrt{8.2169} \\v=2.866 m/s[/tex]
where [tex]m_k[/tex] is the mass of the cat, [tex]m_h[/tex] is the mass of the swing, g is the acceleration due to gravity, h is the height, and v is the speed of the cat.
Therefore,the speed of the cat is found to be 2.866 m/s.
Maximum height of the swing:
Using the principle of conservation of mechanical energy, we can also determine the maximum height the swing can reach. At the highest point, the swing has only potential energy, which is equal to the initial gravitational potential energy.
Using the conservation of mechanical energy equation:
[tex]0.5(m_k+m_h)v^{2}=(m_k+m_h)gH_m_a_x\\[/tex]
where [tex]H_m_a_x[/tex] is the maximum height the swing can reach.
So, [tex]H_m_a_x[/tex] will be,
[tex]0.5(5.00+1.50)v^{2} \times 8.2169=(5.00+1.05) \times 9.8 \times H_m_a_x\\ 26.70=63.7H_m_a_x\\H_m_a_x=0.419 m[/tex]
Thus,the maximum height is 0.419 m.
In conclusion,The speed of the cat as it leaves the swing is 2.866 m/s and the maximum height is 0.419 m.
Learn more about speed here: brainly.com/question/27888149
#SPJ11
A house with its own well has a pump in the basement with an output pipe of inner radius 8.74 mm. The pump can maintain a gauge pressure of 4.10 × 10^5 Pa in the output pipe. A showerhead on the second floor (6.70 m above the pump’s output pipe) has 36 holes, each of radius 0.861 mm. The shower is on "full blast" and no other faucet in the house is open. Density of water is 1.00 × 10^3 kg/m3. Ignoring viscosity, with what speed does water leave the showerhead?
The speed of water leaving the showerhead is 11.9 m/s.
To solve this problem, we can use the following equations:
P = ρgh
Where:
P is the pressure in Pa
ρ is the density of water in kg/m^3
g is the acceleration due to gravity (9.8 m/s^2)
h is the height in m
v = √(2gh)
Where:
v is the velocity in m/s
g is the acceleration due to gravity (9.8 m/s^2)
h is the height in m
The pressure at the pump is equal to the gauge pressure plus atmospheric pressure. The atmospheric pressure at sea level is 1.013 × 10^5 Pa.
P₁ pump = 4.10 × 10^5 Pa + 1.013 × 10^5 Pa
= 5.11 × 10^5 Pa
The pressure at the showerhead is equal to the atmospheric pressure.
P₂ showerhead = 1.013 × 10^5 Pa
The pressure difference is then equal to the pump pressure minus the showerhead pressure.
ΔP = P₁ pump - P₂ showerhead
= 5.11 × 10^5 Pa - 1.013 × 10^5 Pa
= 4.097 × 10^5 Pa
Now that we know the pressure difference, we can calculate the velocity of the water leaving the showerhead.
v = √(2 * 9.8 m/s^2 * 6.70 m)
= 11.9 m/s
Therefore, the speed of water leaving the showerhead is 11.9 m/s.
To learn more about atmospheric pressure click here; brainly.com/question/30780169
#SPJ11
The speed of light with a wavelength 589 nm in light flint glass is 1.90x10^8 m/s. What is an index of refraction of the glass at this wavelength?
The index of refraction of the glass at this wavelength is 1.5773.
The index of refraction of a medium describes how much the speed of light in the medium differs from its speed in a vacuum.
According to the formula,
n = c / v
where n is the refractive index of the medium, c is the speed of light in a vacuum (299,792,458 m/s), and v is the speed of light in the medium.
We have, Given: λ = 589 nm = 589 × 10⁻⁹ m, v = 1.90 × 10⁸ m/s
We need to calculate n.
We can calculate the speed of light in the medium by dividing the speed of light in a vacuum by the refractive index of the medium,
v = c / n
Here, c = 299,792,458 m/s.
Substituting the given values, 1.90 × 10⁸ m/s = (299,792,458 m/s) / n
Solving this for n, we get:
n = (299,792,458 m/s) / (1.90 × 10⁸ m/s)= 1.5773
To know more about refraction visit:
https://brainly.com/question/13088981
#SPJ11
In a photoelectric effect experiment, it is observed that green light does eject electrons from a particular metal. Next, when a shorter wavelength of light is used with the same intensity, which result is possible? b Select one or more: Оа. electrons are ejected at a greater rate and with a larger maximum kinetic energy electrons are ejected at a greater rate but with a smaller maximum kinetic energy electrons are ejected at a lower rate and with a smaller maximum kinetic energy O d. electrons are ejected at a lower rate but with a larger maximum kinetic energy O e there are no ejected electrons
Electrons are ejected at a greater rate and with a larger maximum kinetic energy result is possible. Option A is correct.
In the photoelectric effect, when light of a sufficiently high frequency (shorter wavelength) shines on a metal surface, electrons can be ejected from the metal. The intensity of light refers to the brightness or the number of photons per unit area per unit time.
Based on the photoelectric effect, we can deduce the following possibilities when a shorter wavelength of light is used with the same intensity:
a) Electrons are ejected at a greater rate and with a larger maximum kinetic energy.
This possibility is consistent with the photoelectric effect. When shorter wavelength light is used, the energy of individual photons increases, and each photon can transfer more energy to the electrons, resulting in higher kinetic energy for the ejected electrons. Additionally, the greater number of photons (higher rate) can lead to more electrons being ejected.
Therefore, the correct answer is A.
Learn more about Electrons -
brainly.com/question/860094
#SPJ11
You generate a sound wave of 420 Hz with a speaker. The speed of sound is 342 m/s.
What is the wavelength of the sound?
Question 1 options:
143640 m
1.23 m
0.814 m
You generate a sound wave of 420 Hz with a speaker. The speed of sound is 342 m/s.
You are 2 m from the speaker. You hear a loudness of 48 dB. You back up until you are 4 m away. The loudness you hear now is
Question 2 options:
24 dB
12 dB
45 dB
42 dB
A police car with its siren emitting sound at 440 Hz is moving away from you at 30 m/s. The frequency of the sound you hear is
Question 3 options:
440 Hz
less than 440 Hz
greater than 440 Hz
impossible to tell
Some red light has a wavelength of 620 nm (nanometers).
Some blue light has wavelength 460 nm. Is it faster, slower, or the same speed as the red light?
Question 4 options:
faster
slower
same speed
The colors of light differ in their wavelengths, not in their speed. Hence, red and blue light have the same speed in a vacuum.
1. We can use the equation:v = fλWhere v = speed of sound, f = frequency of the sound wave and λ = wavelength of the sound wave. Here,
v = 342 m/s
f = 420 Hzλ
= v/f
λ = v/f
= 342/420
= 0.814 m
Hence, the wavelength of the sound wave is 0.814 m
.2. The loudness of sound depends on the distance between the source and the listener. The inverse-square law states that the intensity of sound waves reduces as the distance between the listener and the source increases. The loudness of sound decreases by 6 dB when the distance is doubled. Hence, when the distance is halved, the loudness increases by 6 dB. We can use this law to solve this problem. Let's say the loudness at a distance of 2 m is x dB. Then, the loudness at a distance of 4 m would be (x - 6) dB. From the given data, we know that:
x - 6 = 48 - 6 = 42 dB
Therefore, the loudness at a distance of 4 m would be 42 dB.
3. When a sound source moves towards a stationary observer, the frequency of the sound waves received by the observer increases. Similarly, when the sound source moves away from the observer, the frequency of the sound waves received by the observer decreases. This phenomenon is called the Doppler effect. The Doppler effect formula is:
f = f0(v + vo) / (v + vs)
where f0 is the frequency emitted by the source, f is the frequency received by the observer, v is the speed of sound, vo is the velocity of the observer and vs is the velocity of the source. In this case, the frequency emitted by the source (police car) is 440 Hz. The velocity of sound (v) is 342 m/s. The car is moving away from you, so vs is negative. Therefore, we can use the following equation:
f = f0(v - vo) / (v - vs)
f = 440(342 - 30) / (342 + 0)
f = 397.2 Hz
Therefore, the frequency of the sound you hear is less than 440 Hz.
4. The speed of light is constant in a vacuum and is approximately 3 × 10⁸ m/s. The speed of light in air, water, or any other medium is slower than its speed in a vacuum. However, the speed of different colors of light in a vacuum is the same. The colors of light differ in their wavelengths, not in their speed. Hence, red and blue light have the same speed in a vacuum.
To know more about wavelengths visit:
https://brainly.com/question/31143857
#SPJ11
In a particular fission of a uranium-235 (235 U) nucleus, which has neutral atomic mass 235.0439 u, a reaction energy of 200 MeV is released. (a) A mass of 1.00 kg of pure U contains how many
atoms? (b) How much total energy is released if the entire mass of 1.00 kg of 33U fissions? (c) Suppose that these fission reactions occur at a rate to release a constant 100 W of power to a lamp for a long period of time. Assuming 100% of the reaction energy goes into powering the lamp, for how
many years can the lamp run?
A particular fission of a uranium-235 (235 U) nucleus, which has neutral atomic mass 235.0439 u, a reaction energy of 200 MeV is released.(a)1.00 kg of pure uranium contains approximately 2.56 x 10^24 uranium-235 atoms.(b)the total energy released if the entire mass of 1.00 kg of uranium-235 undergoes fission is approximately 3.11 x 10^13 joules.(c)assuming 100% of the reaction energy goes into powering the lamp, the lamp can run for approximately 983,544 years.
(a) To determine the number of uranium-235 (235U) atoms in 1.00 kg of pure uranium, we need to use Avogadro's number and the molar mass of uranium-235.
Calculate the molar mass of uranium-235 (235U):
Molar mass of uranium-235 = 235.0439 g/mol
Convert the mass of uranium to grams:
Mass of uranium = 1.00 kg = 1000 g
Calculate the number of moles of uranium-235:
Number of moles = (Mass of uranium) / (Molar mass of uranium-235)
Number of moles = 1000 g / 235.0439 g/mol
Use Avogadro's number to determine the number of atoms:
Number of atoms = (Number of moles) × (Avogadro's number)
Now we can perform the calculations:
Number of atoms = (1000 g / 235.0439 g/mol) × (6.022 x 10^23 atoms/mol)
Number of atoms ≈ 2.56 x 10^24 atoms
Therefore, 1.00 kg of pure uranium contains approximately 2.56 x 10^24 uranium-235 atoms.
(b) To calculate the total energy released if the entire mass of 1.00 kg of uranium-235 undergoes fission, we need to use the energy released per fission and the number of atoms present.
Given:
Reaction energy per fission = 200 MeV (mega-electron volts)
Convert the reaction energy to joules:
1 MeV = 1.6 x 10^-13 J
Energy released per fission = 200 MeV ×(1.6 x 10^-13 J/MeV)
Calculate the total number of fissions:
Total number of fissions = (Number of atoms) × (mass of uranium / molar mass of uranium-235)
Multiply the energy released per fission by the total number of fissions:
Total energy released = (Energy released per fission) × (Total number of fissions)
Now we can calculate the total energy released:
Total energy released = (200 MeV) * (1.6 x 10^-13 J/MeV) × [(2.56 x 10^24 atoms) × (1.00 kg / 235.0439 g/mol)]
Total energy released ≈ 3.11 x 10^13 J
Therefore, the total energy released if the entire mass of 1.00 kg of uranium-235 undergoes fission is approximately 3.11 x 10^13 joules.
(c) To calculate the number of years the lamp can run, we need to consider the power generated by the fission reactions and the total energy released.
Given:
Power generated = 100 W
Total energy released = 3.11 x 10^13 J
Calculate the time required to release the total energy at the given power:
Time = Total energy released / Power generated
Convert the time to years:
Time in years = Time / (365 days/year ×24 hours/day ×3600 seconds/hour)
Now we can calculate the number of years the lamp can run:
Time in years = (3.11 x 10^13 J) / (100 W) / (365 days/year × 24 hours/day * 3600 seconds/hour)
Time in years ≈ 983,544 years
Therefore, assuming 100% of the reaction energy goes into powering the lamp, the lamp can run for approximately 983,544 years.
To learn more about Avogadro's number visit: https://brainly.com/question/859564
#SPJ11
A fluid of specific gravity 1.0 is flowing through a horizontal conduit at a velocity 2.0 m/s before descending 11 m to a lower portion of the conduit where it travels horizontally at 9.0 m/s. What is the pressure difference (P_lower- P−upper) between the lower portion and the upper portion of the conduit? Your Answer: Answer units
The pressure difference (P2 - P1) between the lower portion and the upper portion of the conduit is -38,555 Pa.
Given data: Specific gravity (SG) = 1.0
Velocity at upper portion (V1) = 2.0 m/s
Distance from upper portion (H1) = 0 m
Velocity at lower portion (V2) = 9.0 m/s
Distance from lower portion (H2) = 11 m
To find: Pressure difference (P2 - P1) between the lower portion and the upper portion of the conduit
Formula used:P + (1/2)ρV² + ρgh = constant Where, P = pressureρ = density
V = velocityg = acceleration due to gravity
h = height
Let's consider upper portion,
Using the above-mentioned formula:P1 + (1/2)ρV1² + ρgH1 = constant -----(1)
P1 = constant - (1/2)ρV1² - ρgH1P1 = constant - (1/2)ρ
V1² - ρg(0) //
At upper portion, height (H1) = 0, g= 9.81 m/s²P1 = constant - (1/2)ρV1² -------(2)
Let's consider the lower portion:Using the above-mentioned formula:
P2 + (1/2)ρV2² + ρgH2 = constant ----- (3)
P2 = constant - (1/2)ρV2² - ρgH2 -------(4)
Subtracting equation (2) from equation (4), we get,
P2 - P1 = - 1/2 ρ (V2² - V1²) + ρg (H2 - H1)
= - 1/2 ρ (9.0 m/s)² - (2.0 m/s)² + ρg (11 m - 0 m)
= -0.5 ρ (81 - 4) + ρg (11)
= -0.5 × 1000 × 77 + 9.81 × 11
= -38,555 Pa
Therefore, the pressure difference (P2 - P1) between the lower portion and the upper portion of the conduit is -38,555 Pa.
Learn more about pressure difference
brainly.com/question/13390708
#SPJ11
1. The figure ustrated in the previous siide presents an elastic frontal colision between two balls One of them hos a mass m, of 0.250 kg and an initial velocity of 5.00 m/s. The other has a mass of m, 0.800 kg and is initially at rest. No external forces act on the bolls. Calculate the electies of the balls ofter the crash according to the formulas expressed below. Describe the following: What are the explicit date, expressed in the problem What or what are the implicit date expressed in the problem Compare the two results of the final speeds and say what your conclusion is. 2 3 4. -1-+ Before collision m2 mi TOL 102=0 After collision in
The figure in the previous siide presents an elastic frontal collision between two balls One of them hos a mass m, of 0.250 kg and an initial velocity of 5.00 m/s 3.125 J = (0.125 kg) * (v1f^2) + (0.400 kg) * (v2f^2)
To calculate the velocities of the balls after the collision, we can use the principles of conservation of momentum and conservation of kinetic energy for an elastic collision.
Let the initial velocity of the first ball (mass m1 = 0.250 kg) be v1i = 5.00 m/s, and the initial velocity of the second ball (mass m2 = 0.800 kg) be v2i = 0 m/s.
Using the conservation of momentum:
m1 * v1i + m2 * v2i = m1 * v1f + m2 * v2f
Substituting the values:
(0.250 kg) * (5.00 m/s) + (0.800 kg) * (0 m/s) = (0.250 kg) * v1f + (0.800 kg) * v2f
Simplifying the equation:
1.25 kg·m/s = 0.250 kg·v1f + 0.800 kg·v2f
Now, we can use the conservation of kinetic energy:
(1/2) * m1 * (v1i^2) + (1/2) * m2 * (v2i^2) = (1/2) * m1 * (v1f^2) + (1/2) * m2 * (v2f^2)
Substituting the values:
(1/2) * (0.250 kg) * (5.00 m/s)^2 + (1/2) * (0.800 kg) * (0 m/s)^2 = (1/2) * (0.250 kg) * (v1f^2) + (1/2) * (0.800 kg) * (v2f^2)
Simplifying the equation:
3.125 J = (0.125 kg) * (v1f^2) + (0.400 kg) * (v2f^2)
Now we have two equations with two unknowns (v1f and v2f). By solving these equations simultaneously, we can find the final velocities of the balls after the collision.
To know more about collision refer here:
https://brainly.com/question/13138178#
#SPJ11