The
solar irradiance
emitted from temperatures of 5000 K, 5500 K, and 6000 K at the top of the earth's atmosphere can be computed using the Stefan-Boltzmann law which states that the total radiant heat energy (J/s) emitted by a surface is proportional to the fourth power of its absolute temperature (K).
Mathematically, the law can be expressed as;E = σT^4where E is the total emitted energy, T is the absolute temperature in Kelvin, and σ is the
Stefan-Boltzmann constant
(5.67 × 10^−8 Wm^−2 K^−4).Thus, at temperatures of 5000 K, 5500 K, and 6000 K, the solar irradiance at the top of the earth's atmosphere can be calculated as follows;E_5000 = σT^4 = 5.67 × 10^−8 × (5000)^4 = 3.89 × 10^7 Wm^−2E_5500 = σT^4 = 5.67 × 10^−8 × (5500)^4 = 5.83 × 10^7 Wm^−2E_6000 = σT^4 = 5.67 × 10^−8 × (6000)^4 = 8.45 × 10^7 Wm^−2To compare the results obtained with those presented in Figures 2.9 and 2.10, the plots of the spectral solar irradiance as a function of wavelength for the three
temperatures
should be generated. The results can be compared based on the
wavelength
ranges and peak irradiance values obtained in the two figures.
Learn more about
solar irradiance
https://brainly.com/question/12974688
#SPJ11
By comparing the computed values with the figures, we can analyze the differences and similarities in the solar irradiance at different temperatures.
To compute the solar irradiance at the top of the Earth's atmosphere emitted from temperatures of 5000, 5500, and 6000 K, we can use the Stefan-Boltzmann law, which states that the power radiated by a black body is proportional to the fourth power of its temperature.
The formula for the power radiated by a black body is given by [tex]\rm \(P = \sigma \cdot A \cdot T^4\)[/tex], where P is the power radiated, [tex]\(\sigma\)[/tex] is the Stefan-Boltzmann constant (approximately [tex]\rm \(5.67 \times 10^{-8} \, \text{W/m}^2\text{K}^4\)), \(A\)[/tex] is the surface area of the black body, and T is the temperature in Kelvin.
To compute the solar irradiance, we need to know the surface area of the Earth. Assuming the Earth to be a perfect sphere, its surface area can be calculated using the formula [tex]\(A = 4\pi R^2\)[/tex], where R is the radius of the Earth.
Substituting the values into the formula, we can calculate the solar irradiance for each temperature:
For [tex]\(5000 \, \text{K}\)[/tex]:
Solar irradiance [tex]\rm \(= \sigma \cdot A \cdot T^4\)[/tex]
Substituting the values, we get:
Solar irradiance [tex]\(= 5.67 \times 10^{-8} \cdot (4\pi R^2) \cdot (5000^4)\)[/tex]
Similarly, we can calculate the solar irradiance for temperatures of [tex]\(5500 \, \text{K}\) and \(6000 \, \text{K}\)[/tex].
To compare the results with Figures 2.9 and 2.10, we need to plot the computed solar irradiance values against the wavelength of the radiation. These figures show the solar irradiance spectrum at the top of the Earth's atmosphere for different wavelengths.
Learn more about solar irradiance
https://brainly.com/question/12974688
#SPJ11
6. The primary line current of an open delta connected
transformer is measured to be 100 A.If the turns ratio between the
primary and secondary coils 2 : 1, the line current in the primary
is.
The line current in the primary of an open delta-connected transformer with a measured primary line current of 100 A and a turns ratio of 2:1 between the primary and secondary coils will be 200 A.
In an open delta connection, also known as a V-V connection, two transformers are used to create a three-phase system. One transformer acts as a standard three-phase transformer, while the other transformer is a reduced-capacity transformer. The primary coils of the two transformers are connected in a triangular or delta configuration, hence the name "open delta."
When measuring the line current in the primary of the open delta transformer, the turns ratio between the primary and secondary coils is essential. In this case, the turns ratio is 2:1, which means for every 2 turns in the primary coil, there is 1 turn in the secondary coil.
Since the line current in the primary is measured to be 100 A, we can determine the line current in the secondary by applying the turns ratio. Multiplying the measured primary line current by the turns ratio (2) gives us the secondary line current, 200 A.
Therefore, the line current in the primary of the open delta-connected transformer is 200 A.
To know more about delta-connected transformers click here:
https://brainly.com/question/31748033
#SPJ11
A very long, straight solenoid with a cross-sectional area of 2.34 cm is wound with 89.3 turns of wire per centimeter. Starting at t=0, the current in the solenoid is increasing according to i(t)- (0.174 A/s² ). A secondary winding of 5.0 turns encircles the solenoid at its center, such that the secondary winding has the same cross-sectional area as the solenoid. 3 of 5 Constanta Part A What is the magnitude of the emt induced in the secondary winding at the instant that the current in the solenoid is 32 A7 Express your answer with the appropriate units. ?
The magnitude of the induced emf in the secondary winding is zero at the instant when the current in the solenoid is 32 A. The magnitude of the electromotive force (emf) induced in the secondary winding of the solenoid, we can use Faraday's law of electromagnetic induction, which states that the emf induced is equal to the rate of change of magnetic flux through the winding.
The magnetic flux (Φ) through a solenoid is given by the equation:
Φ = B * A
Where:
B is the magnetic field inside the solenoid,
A is the cross-sectional area of the solenoid.
The magnetic field inside a solenoid can be approximated as:
B = μ₀ * N * i
μ₀ is the permeability of free space (constant),
N is the number of turns per unit length of the solenoid,
i is the current in the solenoid.
A = 2.34 cm² (cross-sectional area of the solenoid),
N = 89.3 turns/cm (number of turns per unit length of the solenoid),
i = 32 A (current in the solenoid).
A = 2.34 cm² * (1 m / 100 cm)² = 2.34 x 1[tex]0^(-4[/tex]) m²
B = μ₀ * N * i = (4π x [tex]10^(-7[/tex]) T·m/A) * (89.3 turns/m) * (32 A) = 3.60 x 10^(-3) T
emf = -N₂ * dΦ/dt
N₂ is the number of turns in the secondary winding,
dΦ/dt is the rate of change of magnetic flux through the secondary winding.
N₂ = 5 turns,
dΦ/dt = -d(B * A)/dt = -A * dB/dt
Since the magnetic field B is constant, dB/dt = 0, and therefore dΦ/dt = 0.
As a result, the magnitude of the induced emf in the secondary winding is zero at the instant when the current in the solenoid is 32 A.
Learn more about magnetic field here:
https://brainly.com/question/30331791
#SPJ11
What distance does an oscillator of amplitude a travel in 9. 5 periods?
The distance traveled by an oscillator of amplitude a in 9.5 periods is equal to 9.5 times the circumference of the path traced by the oscillator, which is 9.5 times 2πa.
In an oscillator, the amplitude represents the maximum displacement from the equilibrium position. The distance traveled by an oscillator in one complete period is equal to the circumference of the path traced by the oscillator.
The circumference can be calculated using the formula:
Circumference = 2π × radius
In this case, the radius is equal to the amplitude (a). Therefore, the distance traveled in one period is:
Distance per period = 2πa
To find the total distance traveled in 9.5 periods, we can multiply the distance per period by the number of periods:
Total distance = Distance per period × Number of periods
= 2πa × 9.5
Learn more about oscillator here :-
https://brainly.com/question/15780863
#SPJ11
Light of 580 nm passing through a single slit, shows a diffraction pattern on a screen 4.50 m behind the all
as the one in the graph below.
a) What is the width of the central maximum?
b) Can we consider small angle approximation? Consider first minimum for order of magnitude (show
calculations that support your answer)
c) What is the width of the slit?
d) What is the distance from the central maximum to the 5th minimum?
e) If the length between the screen and the slit was increased, would the central maximum get wider,
narrower or it will not change?
f) If the width of the slit was increased, would the central maximum get wider, narrower or it will not
change?
The graph:
Question 2: The camera of a satellite has a diameter of 40cm. The satellite is orbiting 250 km from the surface of earth. What is the minimum distance 2 objects could be on the surface of earth to be result by this camera? Consider 500 cm light.
a) the width of the central maximum is 2.36 mm.b)Small angle approximation is valid.c)The width of the slit is 41.7 µm.
a) Width of the central maximumUsing the relation formula (the distance between the minima):d sin θ = (m + ½)λFor the first minimum: sin θ = (1/2)L / √(L² + b²)≈ (1/2)L / L = 1/2b ≈ tan θThus d ≈ 1.22λ / b= 1.22 × 580 nm / 0.30 mm≈ 2.36 × 10⁻³ m = 2.36 mmThe width of the central maximum is 2.36 mm.
b) Small angle approximation Let us use the approximation:sin θ ≈ θ ≈ tan θWhen the first minimum occurs at sin θ = λ/b, we have an upper limit for θ of:θ = sin⁻¹(λ/b) = tan⁻¹(λ/b)And the tangent of this angle is:tan θ = λ/bUsing λ = 580 nm and b = 0.3 mm, we get:tan θ ≈ 0.002 ≈ θThe small angle approximation is valid.
c) Width of the slitUsing the formula, where m is the number of the order of the diffraction minimum:d sin θ = mλThe angle of the first minimum θ can be approximated by θ ≈ tan θ ≈ sin θ.Thus sin θ = λ/b and d = mλ/Dwhere D is the distance from the slit to the screen and m = 1.Let's find D by using the ratio of the triangle's sides:D / b = L / √(L² + b²).
Then D = bL / √(L² + b²)We have:b = 0.3 mmL = 4.50 mD = bL / √(L² + b²)≈ 0.0139 mλ = 580 nmUsing the formula, we get:d = mλ / D≈ 0.000580 / 0.0139 m≈ 4.17 × 10⁻⁵ m = 41.7 µmThe width of the slit is 41.7 µm.
Learn more about angle here,
https://brainly.com/question/1309590
#SPJ11
Early 20th-century models predicted that a hydrogen atom would be approximately 10⁻¹⁰ in "size." (a) Assuming that the electron and proton are separated by r = 1.0 x 10⁻¹⁰ m, calculate the magnitude (in N) of the electrostatic force attracting the particles to each other. _________ N (b) Calculate the electrostatic potential energy (in eV) of a hydrogen atom (an atom containing one electron, one proton, and possibly one, two, or three neutrons-which do not participate in electrostatic interactions). ____________ eV
(a) Assuming that the electron and proton are separated by r = 1.0 x 10⁻¹⁰ m, calculate the magnitude (in N) of the electrostatic force attracting the particles to each other2.304N.(b)The electrostatic potential energy of a hydrogen atom is approximately -14.4 × 10^(19) eV.
(a) To calculate the magnitude of the electrostatic force between the electron and proton in a hydrogen atom, we can use Coulomb's law. Coulomb's law states that the force between two charged particles is directly proportional to the product of their charges and inversely proportional to the square of the distance between them.
Coulomb's law equation:
F = k × (|q₁| × |q₂|) / r^2
where F is the force, k is the electrostatic constant (9 × 10^9 N m²/C²), q₁ and q₂ are the magnitudes of the charges, and r is the distance between the charges.
In the case of a hydrogen atom, the charges involved are the charge of the electron (e = 1.6 × 10^(-19) C) and the charge of the proton (e = 1.6 × 10^(-19) C). The distance between them is given as r = 1.0 × 10^(-10) m.
Substituting the values into the equation:
F = (9 × 10^9 N m²/C²) × ((1.6 × 10^(-19) C) × (1.6 × 10^(-19) C)) / (1.0 × 10^(-10) m)²
F ≈ 2.304 N
Therefore, the magnitude of the electrostatic force attracting the electron and proton in a hydrogen atom is approximately 2.304 N.
(b) The electrostatic potential energy of a hydrogen atom can be calculated using the equation:
Potential energy = -k × (|q₁| * |q₂|) / r
In this case, we consider the potential energy of the electron and proton interaction.
Substituting the given values:
Potential energy = -(9 × 10^9 N m²/C²) × ((1.6 × 10^(-19) C) × (1.6 × 10^(-19) C)) / (1.0 × 10^(-10) m)
Potential energy ≈ -2.304 J
To convert the potential energy from joules (J) to electron volts (eV), we can use the conversion factor:
1 eV = 1.6 × 10^(-19) J
Converting the potential energy:
Potential energy = (-2.304 J) / (1.6 × 10^(-19) J/eV)
Potential energy ≈ -14.4 × 10^(19) eV
Therefore, the electrostatic potential energy of a hydrogen atom is approximately -14.4 × 10^(19) eV.
To learn more about Coulomb's law visit: https://brainly.com/question/506926
#SPJ11
Discuss, with reference to five materials selection parameters,
why you would not choose low carbon steel for the application of an
in-expensive household light switch.
Low-carbon steel would not be an ideal choice for an inexpensive household light switch due to several material selection parameters.
When considering materials for an application like a household light switch, various factors need to be taken into account. Here are five materials selection parameters that highlight why low-carbon steel may not be suitable:
1. Conductivity: Low-carbon steel has relatively low electrical conductivity compared to other metals like copper or aluminum. A light switch requires efficient electrical conduction, and low-carbon steel may result in higher resistance and energy loss.
2. Corrosion resistance: Low-carbon steel is prone to corrosion, especially in humid environments or if exposed to moisture. Household switches are frequently touched and exposed to air and humidity, making corrosion resistance a crucial consideration.
3. Durability: Light switches are subject to repetitive usage, requiring a material with good mechanical strength and durability. While low-carbon steel is robust, it may not offer the same level of endurance as other materials like stainless steel or high-impact plastics.
4. Aesthetic appeal: Low-carbon steel may lack the desired aesthetic appearance for a light switch. Commonly, light switches have a sleek and visually appealing design and alternative materials offer more options for customization and surface finishes.
5. Cost-effectiveness: While low-carbon steel is generally affordable, other materials like plastics or certain alloys may provide better cost-effectiveness for a household light switch, especially when considering factors like production, installation, and maintenance costs.
In conclusion, considering factors such as conductivity, corrosion resistance, durability, aesthetic appeal, and cost-effectiveness, low-carbon steel may not be the optimal choice for an inexpensive household light switch.
To know more about Low-carbon steel click here:
https://brainly.com/question/29843280
#SPJ11
An RL circuit is composed of a 12 V battery, a 6.0 Hinductor and a 0.050 Ohm resistor. The switch is closed at t = 0 The time constant is 2.0 minutes and after the switch has been closed a long time the voltage across the inductor is 12 V. The time constant is 1.2 minutes and after the switch has been closed a long time the voltage across the inductor is zero. The time constant is 2.0 minutes and after the switch has been closed a long time the current is The time constant is 1.2 minutes and after the switch has been closed a long time the voltage across the inductor is 12 V.
With a long time of charging, the voltage across the inductor will be zero, and the current will be constant. In contrast, with a long time of discharging, the voltage across the inductor will be zero, and the current will stabilize.
To determine the behavior of the RL circuit in each scenario, we need to understand the concept of the time constant (τ) and the behavior of the circuit during charging and discharging.
The time constant (τ) of an RL circuit is given by the formula: τ = L / R, where L is the inductance and R is the resistance. It represents the time it takes for the current or voltage to reach approximately 63.2% of its maximum or minimum value, respectively.
(a) In the scenario with a time constant of 2.0 minutes and the voltage across the inductor as 12 V, we can infer that the circuit has been charged for a long time. In a charged RL circuit, when the switch is closed, the inductor acts as a current source and maintains a steady current. Thus, the current flowing through the circuit will be constant.
(b) In the scenario with a time constant of 1.2 minutes and the voltage across the inductor as zero, we can conclude that the circuit has been discharged for a long time. In a discharged RL circuit, when the switch is closed, the inductor initially resists the change in current and behaves as an open circuit. Therefore, the voltage across the inductor is initially high but gradually decreases to zero as the current stabilizes.
Learn more about RL circuit here:
https://brainly.com/question/17050299
#SPJ11
QUESTION 5 An axon has a membrane capacitance of 3 x 10 F, membrane resistance of 1 ko. The time constant for this membrane circuit model is Answer ms.
The time constant for this membrane circuit model is 3 seconds. To calculate the time constant for a membrane circuit model, we use the formula:
Time Constant (τ) = Membrane Resistance (R) * Membrane Capacitance (C)
In this case, the membrane capacitance is given as 3 x 10 F and the membrane resistance is given as 1 kΩ.
Converting 1 kΩ to ohms, we have 1 kΩ = 1000 Ω.
Substituting the values into the formula, we get:
Time Constant (τ) = (1 kΩ) * (3 x 10 F)
= 1000 Ω * 3 x 10 F
= 3000 x 10-3 s
= 3 s
Therefore, the time constant for this membrane circuit model is 3 seconds.
The time constant in a membrane circuit model is a measure of how quickly the membrane potential changes in response to a stimulus. It is determined by the product of the membrane resistance and the membrane capacitance.
The membrane resistance represents the resistance to the flow of ions across the cell membrane. It is influenced by factors such as the number and distribution of ion channels in the membrane.
The membrane capacitance represents the ability of the cell membrane to store electrical charge. It is determined by the surface area and thickness of the membrane.
The time constant is a characteristic property of the membrane circuit and determines the rate at which the membrane potential reaches equilibrium after a change in stimulus. A larger time constant indicates a slower response, while a smaller time constant indicates a faster response.
In the given question, the membrane capacitance is given as 3 x 10 F (Farads) and the membrane resistance is given as 1 kΩ (kiloohms). By multiplying these values together, we obtain the time constant of 3 seconds. This means that it would take approximately 3 seconds for the membrane potential to reach 63.2% of its final value in response to a stimulus.
To know more about Membrane Resistance
brainly.com/question/15201747
#SPJ11
A sinusoidal electromagnetic wave in vacuum delivers energy at an average rate of 5.00 μW/m 2
. What are is amplitude of the electric field of this wave? (Note, μ 0
=4π×10 −7
T∙ m/A,ε 0
=8.85×10 −12
C 2
/N⋅m 2
) 0.15 V/m
0.061 V/m
2.05×10 −10
V/m
3.5×10 −6
V/m
Therefore, the amplitude of the electric field of this wave is 0.061 V/m.
The average power of a sinusoidal electromagnetic wave can be defined as follows:Pav=⟨S⟩where Pav is the average power and ⟨S⟩ is the average Poynting vector. The magnitude of the Poynting vector can be expressed as follows:⟨S⟩=12E0B0
where E0 and B0 are the magnitudes of the electric and magnetic fields, respectively. In a vacuum, the speed of light c can be expressed as follows:c=1√μ0ε0where μ0 and ε0 are the permeability and permittivity of free space,
respectively. Given the average power Pav and the permittivity of free space ε0, we can solve for the electric field E0 of the wave as follows:E0=√2Pavε0
The electric field amplitude of a sinusoidal electromagnetic wave in a vacuum that delivers energy at an average rate of 5.00 μW/m2 can be
calculated as follows:E0=√2Pavε0E0=√(2×5×10−6 W/m2×8.85×10−12 C2/N⋅m2)E0=0.061 V/m
Therefore, the amplitude of the electric field of this wave is 0.061 V/m.
to know more about electromagnetic
https://brainly.com/question/14527830?
A closely wound circular coil of 70 turns has a radius of 25 cm. The plane of the coil is rotated from a position where it makes an angle of 45.0° with a magnetic field of 2.30 T to a position parallel to the field. The rotation takes 0.120 s. What is the magnitude of the average emf induced in the coil during the rotation?
The task is to determine the magnitude of the average electromotive force (emf) induced in a closely wound circular coil during a rotation from an angle of 45.0° to a position parallel to a magnetic field. The coil has 70 turns and a radius of 25 cm. The rotation takes 0.120 s.
When a coil rotates in a magnetic field, an emf is induced in the coil according to Faraday's law of electromagnetic induction. The magnitude of the induced emf can be calculated using the formula:
emf = NΔΦ/Δt,
where N is the number of turns in the coil, ΔΦ is the change in magnetic flux, and Δt is the time taken for the rotation.
In this case, the coil initially makes an angle of 45.0° with the magnetic field and is then rotated to a position parallel to the field. The change in magnetic flux, ΔΦ, is given by the product of the magnetic field strength, B, the area of the coil, A, and the cosine of the angle between the normal to the coil and the magnetic field direction:
ΔΦ = B A cosθ.
Since the coil is closely wound and has a circular shape, the area of the coil is πr^2, where r is the radius of the coil.
Substituting the given values of N = 70 turns, B = 2.30 T, r = 25 cm, θ = 45.0°, and Δt = 0.120 s into the equations, we can calculate the magnitude of the average emf induced in the coil during the rotation.
Learn more about electromotive here:
https://brainly.com/question/820393
#SPJ11
A simple pendulum, consisting of a mass on a string of length L, is undergoing small oscillations with amplitude A. a. The mass is increased by a factor of four. What is true about the period? b. The length is increased by a factor of four. What is true about the period? c. The amplitude is doubled. What is true about the period? d. The pendulum is taken to the Moon. Which of the following is true about the period?
(a) Increasing the mass of the pendulum by a factor of four does not affect the period. (b) Increasing the length of the pendulum by a factor of four increases the period by a factor of two. (c) Doubling the amplitude of the pendulum does not affect the period. (d) The period of the pendulum on the Moon would be longer compared to Earth due to the lower gravitational acceleration.
(a) The period of a simple pendulum is independent of the mass. Therefore, increasing the mass of the pendulum by a factor of four does not affect the period.
(b) The period of a simple pendulum is directly proportional to the square root of the length. Increasing the length of the pendulum by a factor of four results in a square root increase of two, which means the period is doubled.
(c) The period of a simple pendulum is independent of the amplitude. Doubling the amplitude of the pendulum does not affect the period.
(d) The period of a simple pendulum is influenced by the acceleration due to gravity. On the Moon, the gravitational acceleration is approximately one-sixth of Earth's gravitational acceleration. As a result, the period of the pendulum on the Moon would be longer compared to Earth, as the lower gravitational acceleration would result in slower oscillations.
Among the given options, the correct statement is that the period of the pendulum would be longer on the Moon compared to Earth due to the lower gravitational acceleration.
Learn more about amplitude here:
https://brainly.com/question/9525052
#SPJ11
Find the Sum and output Carry for the addition of the following
two 4-bit numbers using 4-bit parallel adders if the input carry is
1 ( where N1= 1011 & N2 = 1010)
Sum is 10101 and Output Carry is 1.
N1= 1011 and N2= 1010 using 4-bit parallel adders with input carry as 1.
To find the Sum and output Carry for the addition, we need to follow the below steps:
Step 1: Adding the least significant bits which is 1+0+1 = 10.
Write down 0 and carry 1 to the next column.
Step 2: Adding 1 to 1 with the carry of 1 from the previous step.
It is 1+1+1 = 11.
Write down 1 and carry 1 to the next column.
Step 3: Adding 1 to 0 with the carry of 1 from the previous step. It is 0+1+1 = 10.
Write down 0 and carry 1 to the next column.
Step 4: Adding 1 to 1 with the carry of 1 from the previous step. It is 1+1+1 = 11.
Write down 1 and carry 1 to the next column.
The sum of two 4-bit numbers 1011 and 1010 is 10101.
Output carry is 1.
Therefore, Sum is 10101 and Output Carry is 1.
Learn more about Sum and carry https://brainly.com/question/29224969
#SPJ11
Required information A train, traveling at a constant speed of 22.0 ms. comes to an incline with a constant slope. While going up the incline, the train slows down with a constant acceleration of magnitude 1.40 m/s2 66 Sped How far has the train traveled up the incline after 6.60 s? m
The train has traveled up the incline for 176 m after 6.60 s, using the given data: Speed of train = 22.0 m/s, Constant acceleration = 1.40 m/s², Time = 6.60 s
Formula used: The formula used to calculate the distance covered by the train is given by: `d = vit + 1/2 at²`, where `v` is the initial velocity, `a` is the acceleration, `t` is the time taken and `d` is the distance covered.
Initial speed of the train, u = 22.0 m/s Acceleration of the train, a = 1.40 m/s²Time taken by the train, t = 6.60 s.
Using the formula, d = vit + 1/2 at²`d = 22.0 × 6.60 + 1/2 × 1.40 × (6.60)²``d = 145.2 + 1/2 × 1.40 × 43.56``d = 145.2 + 30.576`d = 175.776 ≈ 176 m
Learn more about acceleration:
https://brainly.com/question/460763
#SPJ11
Assume the mestiy infrared radiation from a heat lamp acts like a continuous wave with wovelength 1. S0 pm. (a) If the famp's 205 W output is focused on a persce's shaulder, over a clecular area 25.5 cm in diameter, what is the intensty in W/m?' Wim 2
(b) What is the pesk electric field strength in kV/m ? x kvim (c) Find the peak magnetic field strength in frt. int
The intensity is found to be approximately 35.6 W/m², the peak electric field strength is approximately 6.6 kV/m, and the peak magnetic field strength is approximately 2.2 μT.
(a) To calculate the intensity (I) in W/m², we use the formula I = P/A, where P is the power and A is the area. Given that the power output is 205 W and the circular area has a diameter of 25.5 cm (or 0.255 m), we can calculate the area (A = πr²) and then substitute the values to find the intensity.
(b) The peak electric field strength (E) in kV/m can be calculated using the formula E = c√(2I/ε₀), where c is the speed of light and ε₀ is the vacuum permittivity. We substitute the calculated intensity into the formula to find the peak electric field strength.
(c) The peak magnetic field strength (B) in T can be determined using the relationship B = E/c, where E is the peak electric field strength and c is the speed of light. We substitute the calculated electric field strength into the formula to find the peak magnetic field strength.
After performing the calculations, the intensity is found to be approximately 35.6 W/m², the peak electric field strength is approximately 6.6 kV/m, and the peak magnetic field strength is approximately 2.2 μT.
Learn more about magnetic field here:
https://brainly.com/question/14848188
#SPJ11
a hedrogen atom moves from the n=3 level to the n=2 level, then i moved from the n=3 level to thr n=1level. which transmission leads to the emission of photon with the longest wavelength
The transition from the n=3 level to the n=2 level in a hydrogen atom leads to the emission of a photon with a longer wavelength compared to the transition from the n=3 level to the n=1 level. Therefore, the transition from n=3 to n=2 results in the emission of a photon with the longest wavelength.
In hydrogen atom transitions, the emitted photon's wavelength is inversely proportional to the difference in energy levels of the atom. The energy of a hydrogen atom at a particular level is given by the equation
E=−13.6eV/[tex]n^{2}[/tex], where
n is the principal quantum number.
When an electron transitions from a higher energy level to a lower energy level, it emits a photon. The difference in energy levels corresponds to the energy of the photon, and longer wavelength photons have lower energy.
Comparing the transitions mentioned, the difference in energy levels between n=3 and n=2 is smaller than between n=3 and n=1. Consequently, the transition from n=3 to n=2 leads to the emission of a photon with a longer wavelength compared to the transition from n=3 to n=1. Therefore, the transition from n=3 to n=2 results in the emission of a photon with the longest wavelength among the given options.
Learn more about photon
https://brainly.com/question/30858842
#SPJ11
Heidi is floating in a raft in a lake. She estimates that waves are hitting the shore once every 14.0 seconds. The wave crests appear to be 18.0 meters apart. What is the speed of these waves? 3.5 m/s O 0.78 m/s O 1.3 m/s O252 m/s
The speed of the waves is approximately 1.29 m/s.
The speed of waves can be calculated using the formula:
Speed = Wavelength / Time
Given:
Time between wave crests = 14.0 seconds
Wavelength (distance between wave crests) = 18.0 meters
Substituting the given values into the formula:
Speed = 18.0 meters / 14.0 seconds
After performing the calculation, the result is approximately 1.29 m/s.
Learn more about Wavelength here:
https://brainly.com/question/7143261
#SPJ11
A rectangular coil 20 cm by 35 cm has 140 turns. This coil produces a maximum emf of 64 V when it rotates with an angular speed of 190 rad/s in a magnetic field of strength B. Part A Find the value of B. Express your answer using two significant figures.
We know that 1cm=0.01m, so l=0.20m, w=0.35m.Substituting the given values, we get B= $\frac{64}{140\times 0.20\times 0.35 \times 190}$B= 0.039 Tesla (approximately)Therefore, the value of B is 0.039 Tesla (approximately).
According to the question,A rectangular coil of length l=20cm and width w=35cm having N=140 turns rotates with an angular speed of ω=190rad/s in a magnetic field of strength B, and it produces a maximum emf of E=64V. We are required to find the value of magnetic field B.Induced emf in a coil is given by the expression E=NBωA sinωt. Here, A is the area of the coil, and N is the number of turns.The area of the coil is given by the product of its length and width.
Therefore, A = lw. We can substitute this value of A in the above equation to get E = NBAω sinωt. Here, ω = 2πf is the angular frequency of the coil, and f is its frequency. For maximum emf, sinωt = 1.Substituting the given values, we get64 = NBAω⇒ B = $\frac{64}{NAω}$Given that, l=20cm, w=35cm, N=140, ω=190 rad/s. We know that 1cm=0.01m, so l=0.20m, w=0.35m.Substituting the given values, we get B= $\frac{64}{140\times 0.20\times 0.35 \times 190}$B= 0.039 Tesla (approximately)Therefore, the value of B is 0.039 Tesla (approximately).
Learn more about Equation here,
https://brainly.com/question/29174899
#SPJ11
c) Give three disadvantages of digital circuit compared to analog. (3 marks)
Three disadvantages of digital circuits compared to analog circuits are: Limited precision, Complexity and Higher power consumption.
Limited precision: Digital circuits operate using discrete values or levels, which limits their precision compared to analog circuits. Analog circuits can represent a continuous range of values, allowing for more precise and smooth representations of signals.
Complexity: Digital circuits often require more complex design and implementation compared to analog circuits. They involve the use of digital logic gates, flip-flops, and other digital components, which can increase the complexity of the circuitry.
Higher power consumption: Digital circuits typically require higher power consumption compared to analog circuits. This is because digital circuits use binary states (0s and 1s) and switching operations, which can lead to increased power dissipation and energy consumption. In contrast, analog circuits operate with continuous signals, which can be more power-efficient in certain applications.
To know more about digital circuits
https://brainly.com/question/31676489
#SPJ11
Is an asteroid orbiting the Sun with a velocity of 585 kilometers per second more than one astronomical unit away from the Sun? The equation of orbital velocity may be a useful reference
The asteroid is not more than one astronomical unit away from the Sun based on the given velocity.
Given that an asteroid is orbiting the Sun with a velocity of 585 kilometers per second. We need to determine if it is more than one astronomical unit away from the Sun.
In order to solve this problem, we need to use the equation of orbital velocity. The equation of orbital velocity is given by:v = [tex]√(GM / r)[/tex]
Where, G is the universal gravitational constant, M is the mass of the central body (in this case, the Sun), r is the distance between the asteroid and the Sun, and v is the orbital velocity of the asteroid.
Substituting the given values, we have:v =[tex]√[(6.674 × 10^-11 Nm^2/kg^2) × (1.989 × 10^30 kg) / (1 AU)][/tex]where 1 astronomical unit (AU) is equal to[tex]1.496 * 10^(11)[/tex] meters.
v = [tex]√[(6.674 × 10^-11 Nm^2/kg^2) × (1.989 × 10^30 kg) / (1.496 × 10^11 m)]v = 29.29 km/s[/tex]
Therefore, the asteroid's velocity of 585 kilometers per second is much greater than the calculated orbital velocity of 29.29 km/s. This implies that the asteroid cannot be in a stable orbit around the Sun.
Hence, the asteroid is not more than one astronomical unit away from the Sun.
Learn more about velocity here:
https://brainly.com/question/31036269
#SPJ11
QS1 KM1 F 1 20 U V W 5 M1 3~ QS2 KM2 U V W 99 M2 IV. Circuit design (25 points) 3~ F2 Two motors MI and M2, M2 shall be started before MI can be started, if press the stop button, Ml stops before M2 stops. Please design the control circuit and try to analyze the work process. 6/7
QS1 KM1 F 1 20 U V W 5 M1 3~ QS2 KM2 U V W 99 M2 IV. Circuit design (25 points) 3~ F2 Two motors MI and M2, M2 shall be started before MI can be started, if press the stop button, Ml stops before M2 stops.
The control circuit for the given problem can be designed by using the concept of ladder logic.
Working of the circuit:
When the start button (QS2) is pressed, power is supplied to the K1 contact of the KM2 coil. This makes the coil KM2 energized and its contact KM2 is latched. The contact KM2 of KM2 coil provides power supply to the coil KM1 through the F1 and F2 contacts. When the coil KM1 is energized, its contact KM1 is closed which provides power to the motor M2 and also to the coil M1.After some time delay, the F1 contact of KM1 is closed which provides power to the motor MI. If any of the stop button is pressed, the power supply to the M1 coil is cutoff which stops the motor MI immediately. But the power supply to M2 coil is not cutoff, and it stops after a while as there is no feedback control provided.The F2 contact of KM2 is provided to provide a hold-on condition to KM2 after the stop button is released. This ensures that M2 runs for some time delay before it stops.
Learn more about motors: https://brainly.com/question/25543272
#SPJ11
The Maxwell speed distribution (a) Verify from the Maxwell speed distribution that the most likely speed of a molecule is √2kT/m. - (b) Use a computer to plot the Maxwell speed distribution for nitrogen molecules at T 300 K and T 600 K. Plot both graphs on the same axes, and label the axes values.
The Maxwell speed distribution of a gas is given by the expression,1. f(v) = (m/2πkT)3/2 exp[-m*v2/2kT]. Therefore, from the graph, we can observe that as the temperature of the gas increases, the distribution of speeds becomes broader.
Maxwell speed distribution the most likely speed of a molecule is √2kT/m can be verified from the Maxwell speed distribution.
The Maxwell speed distribution of a gas is given by the expression,1. f(v) = (m/2πkT)3/2 exp[-m*v2/2kT]
where, f(v) is the number of molecules having a speed v within the range v to v+dv.
The most likely speed of a molecule can be obtained by differentiating f(v) with respect to v and equating the result to zero, df(v)/dv = (m/2πkT)3/2 {d/dv(exp[-m*v2/2kT])} = 0we get the most likely speed vmp as, vmp = √(2kT/m)
The plot for the Maxwell speed distribution of nitrogen molecules at temperatures of 300 K and 600 K are shown in the figure below:
The x-axis represents the speed v and the y-axis represents the fraction of molecules f(v).
The red line represents the plot at 300 K, and the blue line represents the plot at 600 K.
Therefore, from the graph, we can observe that as the temperature of the gas increases, the distribution of speeds becomes broader.
Learn more about Maxwell speed distribution here:
https://brainly.com/question/31648187
#SPJ11
A heat pump with a C.O.P equal to 2.4, consumes 2700 kJ of electrical energy during its operating period. During this operating time, 1)how much heat was transferred to the high-temperature tank?
2)How much heat has been moved from the low-temperature tank?
Therefore, the amount of heat transferred to the high-temperature tank is 6480 kJ and the amount of heat moved from the low-temperature tank is 3780 kJ.
1)The heat transferred to the high temperature tank can be found out using the given equationQh = COP * WWhere,Qh = Heat transferred to the high-temperature tankCOP = Coefficient of PerformanceW = Work done by the system
Substituting the given values, we haveQh = 2.4 * 2700kJQh = 6480 kJ2)The heat moved from the low-temperature tank can be found out using the formulaQl = Qh - WWhere,Ql = Heat moved from the low-temperature tankQ
h = Heat transferred to the high-temperature tankW = Work done by the systemSubstituting the values from part 1 and work done from the given question, we haveQl = 6480 kJ - 2700 kJQl = 3780 kJ
Therefore, the amount of heat transferred to the high-temperature tank is 6480 kJ and the amount of heat moved from the low-temperature tank is 3780 kJ.
to know more about low-temperature
https://brainly.com/question/15273514
#SPJ11
A capacitor with C = 1.50⋅10^-5 F is connected as shown in the figure to a resistor R = 980 Ω and a source of emf. with ε = 18.0 V and negligible internal resistance.
Initially the capacitor is uncharged and switch S is in position 1. Then the switch is moved to position 2 so that the capacitor begins to charge. When the switch has been in position 2 for 10.0 ms, it is brought back to position 1 so that the capacitor begins to discharge.
Calculate:
a) The charge of the capacitor.
b) The potential difference between the ends of the resistor and the capacitor just before the switch is moved from position 2 to position 1 again.
c) The potential difference between the ends of the resistor and the capacitor immediately after the switch is brought back from position 2 to position 1.
d) The charge of the capacitor 10.0 ms after the switch is returned from position 2 to position 1.
a) The charge of the capacitor is [tex]1.80 \times 10^{-4}\ C[/tex].
b) The potential difference between the ends of the resistor and the capacitor just before the switch is moved from position 2 to position 1 is 18.0 V.
c) The potential difference between the ends of the resistor and the capacitor immediately after the switch is brought back from position 2 to position 1 is 0 V.
d) The charge of the capacitor 10.0 ms after the switch is returned from position 2 to position 1 is [tex]9.18 \times 10^{-5} C.[/tex]
a) The charge of the capacitor can be calculated using the formula Q = C × V, where Q is the charge, C is the capacitance, and V is the potential difference across the capacitor. Initially, the capacitor is uncharged, so the charge is 0.
b) The potential difference between the ends of the resistor and the capacitor just before the switch is moved from position 2 to position 1 is equal to the emf of the source, which is 18.0 V. This is because when the switch is in position 2, the capacitor is fully charged and the potential difference across it is equal to the emf of the source.
c) When the switch is moved from position 2 to position 1, the capacitor starts to discharge. At the instant the switch is moved, the potential difference between the ends of the resistor and the capacitor immediately becomes 0 V. This is because the capacitor starts to lose its stored charge, and as a result, the potential difference across it drops to 0 V.
d) To calculate the charge of the capacitor 10.0 ms after the switch is returned from position 2 to position 1, we can use the equation )[tex]Q = Q_{0} \times e^{-t/RC}[/tex], where [tex]Q_{0}[/tex] is the initial charge, t is the time, R is the resistance, and C is the capacitance. Since the capacitor was fully charged initially, [tex]Q_{0}[/tex] is equal to the capacitance times the initial potential difference, which is [tex]1.50 \times 10^{-5} \times 18.0[/tex]. Using the given values, we find that the charge is approximately [tex]9.18 \times 10^{-5} C.[/tex]
Learn more about capacitor here:
https://brainly.com/question/32648063
#SPJ11
Pls answer this question
Answer:
3
Explanation:im almost certain thats what it is
The diagram below is a simplified schematic of a mass spectrometer. Positively-charged isotopes are accelerated from rest to some final speed by the potential difference of 3,106 V between the parallel plates. The isotopes, having been accelerated to their final speed, then enter the chamber shown, which is immersed in a constant magnetic field of 0.57 T pointing out of the plane of the schematic. The paths A through G show the trajectories of the various isotopes through the chamber. What will be the radius of the path (in cm) taken by an lon of mass 229 amu and a charge of +2e entering the mass spectrometer's chamber after being accelerated by the parallel plates? Note that. 1 amu =1.66×10 −27
kg and 1c=1.60×10 −19
C.
The radius of the path taken by the ion of mass 229 amu and a charge of +2e entering the mass spectrometer's chamber after being accelerated by the parallel plates is 33.84v cm (where v is the velocity of the ion).
The formula for the radius of path taken by the ion of mass m and charge q in a mass spectrometer's chamber when it enters a magnetic field B at right angles and with a velocity v is given by; R = mv/qBWhere; R is the radius of pathm is the mass of the ionq is the charge on the ionv is the velocity of the ionB is the magnetic field strengthTherefore, substituting the values given; m = 229 amu = 229 × 1.66 × 10⁻²⁷ kgq = +2e = +2 × 1.60 × 10⁻¹⁹ CV = v (since the question did not give the velocity of the ion)B = 0.57 T into the formula,R = mv/qBR = (229 × 1.66 × 10⁻²⁷ kg) (v) / (+2 × 1.60 × 10⁻¹⁹ C) (0.57 T)R = (3.794 × 10⁻²⁵ v) / (1.12 × 10⁻¹⁹)R = 33.84 v.
Therefore, the radius of the path taken by the ion of mass 229 amu and a charge of +2e entering the mass spectrometer's chamber after being accelerated by the parallel plates is 33.84v cm (where v is the velocity of the ion). It is important to note that the actual value of the radius of the path taken by the ion is dependent on the velocity of the ion and the value of the magnetic field strength.
Learn more about magnetic field here,
https://brainly.com/question/14411049
#SPJ11
Show that the dielectric susceptibility has no dimensionality (namely, it has no units). (3pts) (b) Consider a capacitor with plate area S=1 cm² and plate-plate distance d=2 cm. The capacitor is filled with material with dielectric constant €r=200. Determine the capacitance.
In the given problem, once we know the dielectric constant εr = 200, we can use this information to determine the capacitance of the capacitor. It is determined by the material's properties and represents the degree to which the material can be polarized in response to an external electric field.
The dielectric susceptibility is a fundamental property of a material that quantifies its response to an electric field. It is defined as the ratio of the electric polarization of the material to the electric field strength applied to it. Mathematically, it is expressed as:
χ = P / ε₀E
Where χ is the dielectric susceptibility, P is the electric polarization, E is the electric field strength, and ε₀ is the vacuum permittivity (a fundamental constant with units of C²/(N·m²)).
To understand why the dielectric susceptibility has no units, we need to examine the components of the equation. The electric polarization, P, is measured in units of electric dipole moment per unit volume (C/m²), and the electric field strength, E, is measured in volts per meter (V/m). The vacuum permittivity, ε₀, has units of C²/(N·m²).
By analyzing the units in the equation, we find that the units of electric dipole moment per unit volume (C/m²) cancel out with the units of the vacuum permittivity (C²/(N·m²)), leaving the dielectric susceptibility as a dimensionless quantity. This means that the dielectric susceptibility is solely a numerical value representing the material's response to an electric field, independent of any specific unit system.
Therefore, in the given problem, once we know the dielectric constant εr = 200, we can use this information to determine the capacitance of the capacitor. However, the dielectric susceptibility itself does not play a direct role in the calculation of capacitance.
Learn more about electric field here:
https://brainly.com/question/11482745
#SPJ11
Suppose a beam of 5 eV protons strikes a potential energy barrier of height 6 eV and thickness 0.25 nm , at a rate equivalent to a current of 1000A (which is extremely high current!). a. How long would you have to wait, on average, for one proton to be transmitted? Give answer in seconds. b. How long would you have to wait if a beam of electrons with the same energy and current would strike potential barrier of the same height and length? Give answer in seconds.
The calculated times for one proton and one electron to be transmitted through the barrier are 1.23 × 10⁻¹⁶ seconds and 3.61 × 10⁻⁸ seconds, respectively.
a) In order to determine the time taken by one proton to transmit the barrier, we will use the tunneling formula as shown below:
[tex]$$t \approx e^{\frac{2 d}{\hbar}\sqrt{2 m \cdot (V-E)}}$$\\[/tex]
Where, d is the thickness of the barrierh is Planck's constantm is the mass of proton
E is the energy of the proton
V is the height of the potential barrier
Thickness of the barrier, d = 0.25 nm
Height of the potential barrier, V = 6 eV
Mass of a proton, m = 1.67 x 10⁻²⁷ kg
Energy of the proton, E = 5 eV = 5 x 1.6 x 10⁻¹⁹ J
Plugging in the data, we get:
[tex]$$t \approx e^{\frac{2 (0.25 x 10^{-9})}{\hbar}\sqrt{2 \cdot 1.67\times10^{-27} \cdot (6 - 5)\cdot 1.6\times10^{-19}}}$$[/tex]
The value of Planck's constant is 6.626 x 10⁻³⁴ Js
Plugging in the data, we get:
[tex]$$t \approx e^{\frac{2 (0.25 x 10^{-9})}{6.626 \times 10^{-34}}\sqrt{2 \cdot 1.67\times10^{-27} \cdot 1.6\times10^{-19}}}$$[/tex]
t ≈ 1.23 × 10⁻¹⁶ seconds
Therefore, we have to wait for 1.23 × 10⁻¹⁶ seconds for one proton to be transmitted through the barrier.
b) Electrons are a lot lighter than protons, so we can assume the mass of the electron to be 9.11 x 10^-31 kg. Hence, we can use the same formula as above to determine the time taken by one electron to transmit the barrier by using the following values:
Thickness of the barrier, d = 0.25 nmHeight of the potential barrier, V = 6 eV
Energy of the electron, E = 5 eV = 5 x 1.6 x 10⁻¹⁹ J
Mass of an electron, m = 9.11 x 10⁻³¹ kg
Plugging in the data, we get:
[tex]$$t \approx e^{\frac{2 (0.25 x 10^{-9})}{\hbar}\sqrt{2 \cdot 9.11\times10^{-31} \cdot (6 - 5)\cdot 1.6\times10^{-19}}}$$[/tex]
t ≈ 3.61 × 10⁻⁸ seconds
Therefore, we have to wait for 3.61 × 10⁻⁸ seconds for one electron to be transmitted through the barrier.
Learn more about proton at: https://brainly.com/question/1481324
#SPJ11
Three charges are arranged in a straight line. In which case does the electric field at the location shown by the dot have the largest magnitude? All the positive (+) or negative (-) charges in the figure have the same magnitude. The dot is not a charge, just a location marker. Assume the charges are separated by the same distance d or multiples of d, i.e. 2d or 3d. A. (-) (+) ⋅ (+) B. (-) ⋅ (+) (-)
C. (-) (-) ⋅ (+) D. (+) ⋅ (-) (+)
E. (-) (-) ⋅ (+)
Answer: Option A is the correct answer.
The electric field is the physical phenomenon that is produced when an electric charge is placed in space. It can be viewed as the influence on a test charge that is in proximity to the charge producing the field. The direction of the field is determined by the charge that is producing it and the magnitude of the field is proportional to the strength of the charge producing it.
It is a vector quantity. The electric field due to a point charge is given by
E = kQ/r²
where E is the electric field, k is Coulomb's constant (9 x 10⁹ Nm²/C²), Q is the charge of the point charge, and r is the distance between the point charge and the test charge. Three charges are arranged in a straight line. In which case does the electric field at the location shown by the dot have the largest magnitude?We can solve this problem using the principle of superposition.
The electric field at the location of the dot is the sum of the electric fields produced by each of the charges.Q1 is negative, Q2 is positive, and Q3 is positive.
The electric field due to Q1 is directed toward the charge, while the electric field due to Q2 and Q3 is directed away from the charges.
Thus, the electric field due to Q1 is stronger than the electric field due to Q2 and Q3. Therefore, the configuration that produces the largest electric field at the location of the dot is (-) (+) ⋅ (+).
Option A is the correct answer.
Learn more about electric field : https://brainly.com/question/19878202
#SPJ11
A mixture of ice and water with total volume 1 litre (and weight 1kg) is placed in a kettle which has a heat capacity of 2900 J/K and which delivers 2kW to the ice/water mixture. If the mixture is 82.4% ice, how long does it take for the kettle to boil? O a. 491 s O b. 566 s O c. 519 s O d. 547 s O e. 584 s
A mixture of ice and water with total volume 1 litre (and weight 1kg) is placed in a kettle. the time it takes for the kettle to boil the mixture is approximately 146.312 seconds.
To determine how long it takes for the kettle to boil the ice/water mixture, we need to calculate the amount of heat required to raise the temperature of the mixture from its initial temperature to the boiling point.
Given:
Total volume of the mixture = 1 liter
Weight of the mixture = 1 kg
Heat capacity of the kettle, C = 2900 J/K
Power delivered to the mixture = 2 kW = 2000 J/s
Percentage of ice in the mixture = 82.4%
First, we can calculate the mass of ice in the mixture:
Mass of ice = 82.4% * 1 kg = 0.824 kg
Next, we can calculate the heat required to raise the temperature of the ice to its melting point, which is 0°C:
Heat required = mass of ice * specific heat of ice * temperature change
Heat required = 0.824 kg * 2100 J/kg°C * (0 - (-10°C)) = 17208 J
Now, we need to calculate the heat required to convert the ice at 0°C to water at 0°C (latent heat of fusion):
Heat required = mass of ice * latent heat of fusion of ice
Heat required = 0.824 kg * 334000 J/kg = 275416 J
Total heat required = Heat required to raise the temperature + Heat required for phase change
Total heat required = 17208 J + 275416 J = 292624 J
Finally, we can calculate the time required using the formula:
Time = Total heat required / Power delivered
Time = 292624 J / 2000 J/s ≈ 146.312 s
Therefore, the time it takes for the kettle to boil the mixture is approximately 146.312 seconds.
Learn more about Heat capacity here:
https://brainly.com/question/28302909
#SPJ11
The wavelength and frequency of an electromagnetic wave are related to each other through the following equation c = λv where c is the speed of light, is the wavelength, and v is the frequency. Rearrange the equation to solve for v. v = _____________________ An electromagnetic wave has a wavelength of 6.09 × 10−7 m. What is the frequency of the electromagnetic wave? v = _____________________Hz
The frequency of the electromagnetic wave is 4.93 × 10^14 Hz` (to two significant figures),
The given equation is `c = λv` where `c` is the speed of light, `λ` is the wavelength, and `v` is the frequency.
To solve for `v`, we need to isolate `v`.
So, first, we will divide both sides by λ:
`c/λ = v` or
v = c/λ`
Now, let's calculate the frequency of the electromagnetic wave whose wavelength is 6.09 × 10^−7 m using the above equation.
`v = c/λ``
v = 3 × 10^8 m/s / (6.09 × 10^−7 m)`
Frequency `v` is given by the formula:
v = c / λ where `c` is the speed of light and `λ` is the wavelength.
Rearranging the formula to solve for `v`:
v = c / λ
Therefore, the frequency of the electromagnetic wave is:` v = 4.93 × 10^14 Hz` (to two significant figures)
Learn more about electromagnetic wave https://brainly.com/question/13874687
#SPJ11