2.1. Exiting humidity: Approximately 22.7%. Amount of water passing through the wicks per hour: Approximately 67.5 kg/h. 2.2. Required rate of heat transfer: Approximately 62.125 kW. Amount of water removed per hour: Approximately 67.5 kg/h.
To calculate the exiting humidity and the amount of water passing through the wicks per hour (2.1), and the required rate of heat transfer and the amount of water removed per hour (2.2), let's go through the steps and calculations.
2.1. Exiting Humidity and Amount of Water Passing Through the Wicks per Hour:
Step 1: Use the steam tables to determine the enthalpies of saturated air at the inlet and outlet temperatures.
Given values from the steam tables:
he1 = 2547.3 kJ/kg
ha2 = 322.8 kJ/kg
hv2 = 2592.2 kJ/kg
Step 2: Use psychometric charts to determine the absolute humidity against the inlet temperature and relative humidity.
Given relative humidity at the exit:
[tex]phi_2 = P_{12} / Pv_2[/tex] = 2.81 kPa / 12.34 kPa ≈ 0.227
This means that the relative humidity at the exit is approximately 22.7%.
Step 3: Calculate the amount of water passing through the wicks per hour.
Given:
Mass flow rate of air (ma) = 2.5 kg/s
Specific humidity (omega) = 0.0075
The amount of water passing through the wicks per hour can be calculated as:
mv = omega * ma = 0.0075 * 2.5 kg/s = 0.01875 kg/s
Converting to per hour:
mv = 0.01875 kg/s * 3600 s/h = 67.5 kg/h
Therefore, the amount of water passing through the wicks per hour is approximately 67.5 kg/h.
2.2. Required Rate of Heat Transfer and Amount of Water Removed per Hour:
Given:
Initial temperature (Ti) = 25°C
Final temperature (T2) = 15°C
Initial humidity (d) = 35%
Initial pressure (P1) = 100 kPa
Mass flow rate of air (m) = 2.5 kg/s
Step 1: Use the steam tables to determine the enthalpies of saturated air at the inlet and outlet temperatures.
Given values from the steam tables:
he1 = 2547.3 kJ/kg
ha1 = 297.68 kJ/kg
Step 2: Use psychometric charts to determine the absolute humidity against the inlet temperature and relative humidity.
Given relative humidity at the exit:
[tex]phi_2[/tex]= 0 (completely dry condition)
Step 3: Calculate the required rate of heat transfer.
The rate of heat transfer can be calculated using the formula:
Q = ma * (ha2 - ha1) + mv * (hv2 - hv1)
Given values:
ma = 2.5 kg/s
mv = omega * ma = 0.0075 * 2.5 kg/s = 0.01875 kg/s
ha2 = 322.8 kJ/kg
ha1 = 297.68 kJ/kg
hv2 = 2592.2 kJ/kg
hv1 = 2547.3 kJ/kg
Q = 2.5 kg/s * (322.8 kJ/kg - 297.68 kJ/kg) + 0.01875 kg/s * (2592.2 kJ/kg - 2547.3 kJ/kg)
Q ≈ 62.125 kJ/s ≈ 62.125 kW
Therefore, the required rate of heat transfer is approximately 62.125 kW.
Step 4: Calculate the amount of water removed per hour.
The amount of water removed per hour can be calculated as:
mv = omega * ma = 0.0075 * 2.5 kg/s = 0.01875 kg/s
Converting to per hour:
mv = 0.01875 kg/s * 3600 s/h = 67.5 kg/h
Therefore, the amount of water removed per hour is approximately 67.5 kg/h.
Learn more about rate of heat transfer here:
https://brainly.com/question/33407501
#SPJ4
The difference between greatest 5-digit number and smallest 6-digit number is
a)0
b)1
c)2
d)10
Non-metals: 18. Ceramics can be crystalline, semi-crystalline, or amorphous. 19. Ceramics generally have a higher tensile strength than compression strength. 20. Tempered glass is stronger than annealed glasses. 21. Ceramics consist of ionic bonds or covalent bonds. 22. Crystallized polyethylene (PE) is denser and stronger than amorphous PE. 23. Polymer stress relaxation is independent of temperature. 24. Elastomers do not have glass transition temperature (T3) 25. Polydispersity index equal to 1 means that all molecular chains in a polymer are equally long.
The statements provided contain various information about non-metals and ceramics. Let's break down each statement and provide a clear explanation for each:
Statement 18: Ceramics can be crystalline, semi-crystalline, or amorphous.
- Ceramics are a type of non-metal material that are known for their high melting points and excellent heat resistance.
- Crystalline ceramics have a regular, ordered arrangement of atoms, which gives them a defined structure.
- Semi-crystalline ceramics have both ordered and disordered regions within their structure.
- Amorphous ceramics lack a well-defined atomic structure and have a more random arrangement of atoms.
Statement 19: Ceramics generally have a higher tensile strength than compression strength.
- Tensile strength refers to a material's ability to resist being pulled apart.
- Compression strength refers to a material's ability to withstand being squeezed together.
- In general, ceramics have stronger resistance to being pulled apart (tensile strength) compared to being squeezed together (compression strength). This is due to the nature of their atomic structure, which allows them to better withstand pulling forces.
Statement 20: Tempered glass is stronger than annealed glasses.
- Tempered glass is a type of glass that undergoes a special heating and cooling process to increase its strength.
- Annealed glass, on the other hand, is the standard form of glass that is cooled slowly to relieve internal stresses.
- Tempered glass is stronger than annealed glass because the heating and cooling process creates surface compression, making it more resistant to breakage.
Statement 21: Ceramics consist of ionic bonds or covalent bonds.
- Ceramics are typically composed of elements with high electronegativity differences, leading to the formation of ionic or covalent bonds.
- Ionic bonds involve the transfer of electrons from one atom to another, creating positive and negative ions that are held together by electrostatic forces.
- Covalent bonds involve the sharing of electrons between atoms, resulting in a strong bond.
Statement 22: Crystallized polyethylene (PE) is denser and stronger than amorphous PE.
- Polyethylene (PE) is a polymer commonly used in various applications.
- Crystallized polyethylene has a more ordered structure with regions of crystallinity, making it denser and stronger compared to amorphous polyethylene, which lacks this ordered structure.
Statement 23: Polymer stress relaxation is independent of temperature.
- Polymer stress relaxation refers to the reduction of stress in a polymer over time when subjected to a constant strain.
- The rate of stress relaxation in polymers is influenced by factors such as temperature, time, and molecular structure.
- However, the statement that polymer stress relaxation is independent of temperature is not accurate. Temperature plays a significant role in polymer behavior, affecting the rate of relaxation and the extent to which stress is relieved.
Statement 24: Elastomers do not have a glass transition temperature (Tg).
- Elastomers are a type of polymer that exhibit large elastic deformation when subjected to stress and return to their original shape when the stress is removed.
- Unlike some other types of polymers, elastomers do not have a distinct glass transition temperature (Tg). The lack of a Tg is due to the flexible nature of the polymer chains, which allows them to move more freely even at low temperatures.
Statement 25: A polydispersity index equal to 1 means that all molecular chains in a polymer are equally long.
- The polydispersity index (PDI) is a measure of the molecular weight distribution in a polymer sample.
- A PDI of 1 indicates a monodisperse polymer sample, where all the molecular chains have the same length.
- In contrast, a higher PDI value indicates a broader distribution of molecular chain lengths in the polymer sample.
Overall, ceramics can have different structures, ceramics generally have higher tensile strength, tempered glass is stronger than annealed glass, ceramics consist of ionic or covalent bonds, crystallized polyethylene is denser and stronger than amorphous polyethylene, polymer stress relaxation is influenced by temperature, elastomers lack a distinct glass transition temperature, and a polydispersity index of 1 means all molecular chains in a polymer are equally long.
To know more about Ceramics :
https://brainly.com/question/30509290
#SPJ11
What products are formed when each peptide is treated with chymotrypsin? Be sure to answer all parts. [1] Ile-Glu-Ile-Trp-Cys-Pro [2] Lys-Arg-Ser-Phe-His-Ala [3] Asp-Lys-Trp-Glu-His-Glu-Ile-Leu-Tyr-Thr-Pro-Cys
When each peptide is treated with chymotrypsin, several products are formed: Asp, Lys, and Trp-Glu-His-Glu-Ile-Leu-Tyr-Thr-Pro-Cys
The process of breaking the peptide bonds into smaller fragments by chymotrypsin is called hydrolysis. The peptide bonds between amino acid residues are broken by chymotrypsin during the hydrolysis process. Two primary proteolytic products are produced when a peptide is hydrolyzed by chymotrypsin. Amino acids and short peptides are among these products, which are produced by the cleavage of the peptide bond.
Thus, the products formed when each peptide is treated with chymotrypsin are given below:
1. Ile-Glu-Ile-Trp-Cys-Pro: When it is treated with chymotrypsin, the peptide bond between the amino acids Ile and Glu is hydrolyzed, resulting in two fragments: Ile-Glu and Ile-Trp-Cys-Pro. Then, the peptide bond between Ile and Glu is hydrolyzed, resulting in three fragments: Ile, Glu, and Ile-Trp-Cys-Pro.
2. Lys-Arg-Ser-Phe-His-Ala: When it is treated with chymotrypsin, the peptide bond between Lys and Arg is hydrolyzed, resulting in two fragments: Lys-Arg and Ser-Phe-His-Ala. Then, the peptide bond between Arg and Ser is hydrolyzed, resulting in three fragments: Lys, Arg, and Ser-Phe-His-Ala.
3. Asp-Lys-Trp-Glu-His-Glu-Ile-Leu-Tyr-Thr-Pro-Cys: When it is treated with chymotrypsin, the peptide bond between the amino acids Lys and Trp is hydrolyzed, resulting in two fragments:
Asp and Lys-Trp-Glu-His-Glu-Ile-Leu-Tyr-Thr-Pro-Cys. Then, the peptide bond between Lys and Trp is hydrolyzed, resulting in three fragments: Asp, Lys, and Trp-Glu-His-Glu-Ile-Leu-Tyr-Thr-Pro-Cys.
Hence, the above-mentioned products are formed when each peptide is treated with chymotrypsin.
Learn more about hydrolysis from the given link:
https://brainly.com/question/30457911
#SPJ11
Determine whether the series In (1) is convergent or divergent by expressing s, as a telescoping k=1 sum. If it is convergent, find its sum. [infinity]0 ln (1) K=1 [.log() = lage (a)-loge (b)] 2 ln (K) == ln (K) - { (K+1) Sn = ln (+) k=1
The series ln(1) is divergent as it approaches negative infinity.
The series ln(1) can be expressed as a telescoping sum using the property ln(a) - ln(b) = ln(a/b).
By applying this property, we rewrite the series as ln(1) = ln(1) - ln(1/2) + ln(2) - ln(2/3) + ln(3) - ln(3/4) + ...
Each term cancels out with the next term, except for the first and last terms.
Simplifying, we get ln(1) - ln(1/∞). As the limit of 1/∞ approaches 0, ln(1/∞) approaches negative infinity. Therefore, the series ln(1) is divergent, meaning it does not converge to a finite value.
The provided explanation explains why the series ln(1) is divergent by expressing it as a telescoping sum and using the property of logarithms.
It clarifies that each term cancels out, except for the first and last terms, and demonstrates how the limit of 1/∞ approaches 0, resulting in negative infinity.
To learn more about logarithms click here
brainly.com/question/30226560
#SPJ11
need help please it's urgent
Answer:
(a) P(Blue) = 0.24
P(Green) = 0.12
(b) 176
Step-by-step explanation:
Part (a)Let x be the probability that the spinner lands on green.
Given the spinner is twice as likely to land on blue than green, the probability of it landing on blue is 2x.
The sum of all probabilities must equal 1, so we can set up the equation:
[tex]0.2 + 2x + x + 0.44 = 1[/tex]
Solve the equation for x:
[tex]\begin{aligned}0.2 + 2x + x + 0.44 &= 1\\3x+0.64&=1\\3x+0.64-0.64&=1-0.64\\3x&=0.36\\3x\div3&=0.36\div3\\x&=0.12\end{aligned}[/tex]
Therefore, the probability of landing on green is 0.12, and the probability of landing on blue is 0.24.
[tex]\begin{array}{|c|c|c|c|c|}\cline{1-5}\vphantom{\dfrac12} \sf Colour& \sf Red& \sf Blue& \sf Green& \sf Yellow\\\cline{1-5}\vphantom{\dfrac12} \sf Probability & 0.2 & 0.24 & 0.12 & 0.44\\\cline{1-5}\end{array}[/tex]
[tex]\hrulefill[/tex]
Part (b)The expected number of times the spinner is expected to land on yellow can be calculated by multiplying the probability of landing on yellow by the total number of spins:
[tex]\begin{aligned}\textsf{Expected number of yellow spins}&=\textsf{Probability of yellow} \times\textsf{Total number of spins}\\&= 0.44 \times 400\\&= 176\end{aligned}[/tex]
Therefore, the spinner is expected to land on yellow 176 times out of 400 spins.
The calculated probabilities of the spinner are:
(a) P(Blue) = 0.24 and P(Green) = 0.12
(b) 176
How to find the probability of the spinner?We are given the probabilities as:
P(Red) = 0.2
P(yellow) = 0.44
Let z be the probability that the spinner lands on green.
We are told that the spinner is twice as likely to land on blue than green, and as such it means that the probability of it landing on blue is 2z
The sum of all probabilities must equal 1, so we can set up the equation:
0.2 + 2z + z + 0.44 = 1
3z + 0.64 = 1
3z = 1 - 0.64
3z = 0.36
z = 0.12
2z = 2 * 0.12 = 0.24
b) If spinner is spun 400 times, then:
N(yellow) = 0.44 * 400 = 176
Read more about Probability of spinner at: https://brainly.com/question/3765462
#SPJ1
The following skeletal oxidation-reduction reaction occurs under basic conditions. Write the balanced REDUCTION half reaction. Enter electrons as e Cu(OH)₂ + F→→ F₂ + Cu Reactants Submit Answer Products Retry Entire Group 9 more group attempts remaining
The balanced reduction half-reaction for the given oxidation-reduction reaction under basic conditions is: Cu(OH)₂ + 2e⁻ → Cu + 2OH⁻, where copper is reduced by gaining two electrons.
To write the balanced reduction half-reaction for the given oxidation-reduction reaction under basic conditions, we need to balance both the atoms and charges. The half-reaction represents the reduction process, where electrons are gained.
The reaction given is:
Cu(OH)₂ + F₂ → Cu + F⁻
First, let's identify the elements that are undergoing oxidation and reduction. In this case, copper (Cu) is being reduced, as it goes from a higher oxidation state of +2 in Cu(OH)₂ to 0 in Cu. Fluorine (F) is being oxidized, as it goes from 0 in F₂ to -1 in F⁻.
To balance the reduction half-reaction, we need to balance the charge by adding electrons (e⁻). The number of electrons should be equal to the change in oxidation state of the element being reduced. In this case, copper is gaining two electrons.
Thus, the balanced reduction half-reaction is:
Cu(OH)₂ + 2e⁻ → Cu + 2OH⁻
This indicates that copper hydroxide (Cu(OH)₂) is reduced to copper (Cu), with the gain of two electrons, and hydroxide ions (OH⁻) are also produced.
To learn more about electrons visit:
https://brainly.com/question/860094
#SPJ11
Poorly-graded gravel or gravel mixed with sand provides............ strength and characteristics while its potential to frost action is........... ......... drainage
a.Good or excellent, excellent, high
b.Poor to fair, poor, very low
c.Good or excellent, excellent, very low
d.Poor to fair, excellent, high
Poorly-graded gravel or gravel mixed with sand provides poor to fair strength and characteristics while its potential to frost action is excellent and drainage is high.
Poorly-graded gravel or gravel mixed with sand typically has a wide range of particle sizes, resulting in a less compacted and stable material. This leads to its poor to fair strength and characteristics. However, when it comes to frost action, poorly-graded gravel or gravel mixed with sand performs excellently. The varying particle sizes allow for better drainage and reduced water accumulation, minimizing the potential for frost heave and damage caused by freezing and thawing cycles. Additionally, the drainage capability of poorly-graded gravel or gravel mixed with sand is very low. The presence of different-sized particles creates void spaces that enhance water movement through the material, promoting effective drainage and preventing waterlogging.
Poorly-graded gravel or gravel mixed with sand exhibits poor to fair strength and characteristics, excellent resistance to frost action, and very low drainage capability.
To know more about gravel visit:
https://brainly.com/question/28855557
#SPJ11
Suppose a hard disk with 3000 tracks, numbered 0 to 2999, is currently serving a request at track 133 and has just finished a request at track 125, and will serve the following sequence of requests: 85, 1470, 913, 1764, 948, 1509, 1022, 1750, 131 Please state the order of processing the requests using the following disk scheduling algorithms and calculate the total movement (number of tracks) for each of them. (1) SSTE (2) SCAN (3) C-SCAN Hints: SSTF: Selects the request with the minimum seek time from the current head position. SCAN: The disk arm starts at one end of the disk, and moves toward the other end, servicing requests until it gets to the other end of the disk, where the head movement is reversed and servicing continues. C-SCAN: The head moves from one end of the disk to the other, servicing requests as it goes. When it reaches the other end, however, it immediately returns to the beginning of the disk, without servicing any requests on the return trip. Treats the cylinders as a circular list that wraps around from the last cylinder to the first one.
The order of processing requests and the total movement for each disk scheduling algorithm are as follows:
(1) SSTE: 133, 131, 85, 125, 1470, 913, 948, 1022, 1509, 1750, 1764. Total movement = 2929 tracks.
(2) SCAN: 133, 1470, 1764, 1750, 1509, 948, 913, 1022, 131, 85, 125. Total movement = 4639 tracks.
(3) C-SCAN: 133, 1764, 1750, 1509, 1022, 948, 913, 85, 131, 125, 1470. Total movement = 5423 tracks.
In the SSTE (Shortest Seek Time First) algorithm, the request with the minimum seek time from the current head position is processed next. Starting from track 133, the order of processing the requests is 85, 133, 125, 1470, 913, 948, 1022, 1509, 1750, 1764, and 131. The total movement is calculated by summing up the absolute differences between consecutive tracks.
In the SCAN algorithm, the disk arm starts at one end of the disk and moves towards the other end, servicing requests along the way. After reaching the other end, the head movement is reversed, and servicing continues. In this case, the order of processing the requests is 85, 133, 1764, 1750, 1509, 948, 913, 131, 125, 1022, and 1470. The total movement is calculated similarly to SSTE.
The C-SCAN (Circular SCAN) algorithm treats the cylinders as a circular list and moves from one end to the other, servicing requests. However, when reaching the other end, it immediately returns to the beginning of the disk without servicing any requests on the return trip. The order of processing the requests using C-SCAN is 85, 133, 913, 948, 1022, 1470, 1509, 1750, 1764, 125, and 131. The total movement is calculated accordingly.
These disk scheduling algorithms aim to minimize the movement of the disk arm and optimize the efficiency of processing requests based on their locations on the disk.
Learn more about algorithm here:
https://brainly.com/question/21172316
#SPJ11
Kuldip's factory manufactures toys that sell for $29.95 each. The variable cost per toy is $11, and the total fixed costs for the month are $45,000. Calculate the unit contribution margin. 1. $17.50 2.$17.95 3.$19.00 4.$18.95
The unit contribution margin is calculated by subtracting the variable cost per unit from the selling price per unit. In this case, the unit contribution margin is $18.95, which represents the amount of revenue available to cover fixed costs and contribute to profit for each toy sold. Thus, the correct answer is option 4.
To calculate the unit contribution margin, we need to first understand the terms "variable cost" and "fixed cost." The variable cost refers to the cost that changes depending on the number of units produced, while the fixed cost remains constant regardless of the number of units produced.
In this case, the variable cost per toy is given as $11, and the total fixed costs for the month are $45,000.
The unit contribution margin can be calculated by subtracting the variable cost per unit from the selling price per unit. In this case, the selling price per toy is $29.95, and the variable cost per toy is $11.
Unit contribution margin = Selling price per toy - Variable cost per toy
Unit contribution margin = $29.95 - $11
Unit contribution margin = $18.95
Therefore, the unit contribution margin is $18.95 (option 4).
Learn more about Selling price at:
https://brainly.com/question/21297845
#SPJ11
Find the solution of the given initial value problem. y (4) - 10y" +25y" = 0; y(1) = 10 +e5, y'(1) = 8 +5e5, y"(1) = 25e5, y" (1) = 125e5. y(t) = How does the solution behave as t- →[infinity]o? Choose one
Given differential equation is y (4) - 10y" +25y" = 0 .The characteristic equation is r⁴ - 10r² + 25 = 0. The above quadratic equation can be factored as (r²-5)²=0.
The roots are r₁
=r₂
=√5 and r₃
=r₄
=-√5.
The solution will behave as t→[infinity] as the exponential function grows at a faster rate than the polynomial expression with respect to time. Hence the solution tends to infinity as t tends to infinity.
To know more about equation, visit:
https://brainly.com/question/29657983
#SPJ11
The solution of the given initial value problem. y (4) - 10y" +25y" = 0; y(1) = 10 +e5, y'(1) = 8 +5e5, y"(1) = 25e5, y" (1) = 125e5. The answer to how the solution behaves as t approaches infinity is indeterminate.
The given initial value problem is y(4) - 10y" + 25y' = 0, with initial conditions y(1) = 10 + e^5, y'(1) = 8 + 5e^5, y"(1) = 25e^5, and y"'(1) = 125e^5.
To solve this problem, we can use the method of solving linear homogeneous differential equations with constant coefficients. We start by finding the characteristic equation, which is r^4 - 10r^2 + 25 = 0.
This equation can be factored as (r^2 - 5)^2 = 0. Therefore, the characteristic equation has a repeated root of r = ±√5.
The general solution of the differential equation is y(t) = (C1 + C2t)e^√5t + (C3 + C4t)te^√5t, where C1, C2, C3, and C4 are constants.
To find the specific solution, we can substitute the initial conditions into the general solution. Using y(1) = 10 + e^5, we find C1 + C2 + C3 + C4 = 10 + e^5.
Using y'(1) = 8 + 5e^5, we find C2 + √5C1 + C4 + √5C3 = 8 + 5e^5.
Using y"(1) = 25e^5, we find C2 + 5C1 + 4√5C3 + 4C4 = 25e^5.
Using y"'(1) = 125e^5, we find C4 + 15C3 + 20√5C1 + 20C2 = 125e^5.
Solving this system of equations will give us the specific solution for y(t).
As t approaches infinity, the behavior of the solution will depend on the values of the constants C1, C2, C3, and C4. Without knowing the specific values, we cannot determine how the solution will behave as t approaches infinity. Therefore, the answer to how the solution behaves as t approaches infinity is indeterminate.
Learn more about solution
https://brainly.com/question/1616939
#SPJ11
How do you find the midpoint of 30 < x ≤ 40
Answer:
To find the endpoint we have to calculate the distance between the known midpoint to the known endpoint. To calculate the midpoint we add two points and divide them by 2.
The formula for midpoint = (x1 + x2)/2, (y1 + y2)/2.
Substituting in the two x-coordinates and two y-coordinates from the endpoints.
Putting it together,
The endpoint formula is:
(x a ,ya)= ((2xm−xb),(2ym−yb))
( x a , y a ) = ( ( 2 x m − x b ) , ( 2 y m − y b ) ).
The end of a line at a point that is equally distant from both ends, a time interval between an event's beginning and end.
The point on a graph or figure where the figure stops might be referred to as the endpoint. It can be the point joining the sides of a polygon (the vertex), the common endpoint of two rays making an angle, the two extreme points of a line segment, the one end of a ray.
To learn more about endpoints and midpoints:
Step-by-step explanation:
this is just an exaple
A reactor contains an amount of hydrogen exploded. i) Estimate this quantity if the blast caused minor damage to house structures (1000 m) from the center of explosion. ii) At what distance the blast will cause partial collapse of walls and roofs of houses if the stored material is 23,324 kg of hydrogen? iii) Using the results of part 'i', calculate the probability of death due to lung hemorrhage, eardrum rupture, glass breakage, and structural damage. Data: The hydrogen heat of combustion = 142×10³ kJ/kg| The energy of TNT = 46,86 kJ/kg Efficiency of explosion = 5%
i. The estimated quantity of hydrogen exploded is [tex]1.39 * 10^7 kg of TNT[/tex]
ii. the blast will cause partial collapse of walls and roofs of houses at a distance of 188 m from the center of explosion.
iii. The estimated probabilities of death due to lung hemorrhage, eardrum rupture, glass breakage, and structural damage are 0.38%, 13.56%, 291.24%, and 3.12%, respectively.
How to estimate quantity of hydrogen explodedWe have been provided with the following values
Stored material = 23,324 kg of hydrogen
Hydrogen heat of combustion = 142×10³ kJ/kg
Energy of TNT = 46.86 kJ/kg
Efficiency of explosion = 5%
Blast causes minor damage to house structures at a distance of 1000 m
(i) Estimate the quantity of hydrogen exploded:
The energy released by the explosion can be estimated using the heat of combustion of hydrogen and the stored quantity of hydrogen as:
Energy released = Stored quantity × Heat of combustion
[tex]= 23,324 kg * 142 * 10^3 kJ/kg\\= 3.31 * 10^9 kJ[/tex]
The energy equivalent of TNT can be calculated as:
Energy of TNT equivalent = Energy released / (Efficiency of explosion × Energy of TNT)
[tex]= 3.31 * 10^9 kJ / (0.05 * 46.86 kJ/kg)\\= 1.39 * 10^7 kg of TNT[/tex]
(ii) Distance for partial collapse of walls and roofs of houses:
This can be calculated using the following equation:
Distance = (Energy released / (Distance factor * Energy of TNT)[tex])^(1/3)[/tex]
where the distance factor depends on the type of structure and ranges from 1.4 to 1.7 for residential structures.
Here, we assume a distance factor of 1.5.
Substitute the values
Distance = [tex](3.31 * 10^9 kJ / (1.5 * 46.86 kJ/kg))^(1/3)[/tex]
= 188 m
Therefore, the blast will cause partial collapse of walls and roofs of houses at a distance of 188 m from the center of explosion.
(iii) Probability of death due to various factors:
The probability of death due to lung hemorrhage, eardrum rupture, glass breakage, and structural damage can be estimated using the following empirical equations:
Probability of lung hemorrhage = 0.00014 * Energy released[tex]^(0.684)[/tex]
Probability of eardrum rupture = 0.063 * Energy released[tex]^(0.385)[/tex]
Probability of glass breakage = 0.005 * Energy released[tex]^(0.5)[/tex]
Probability of structural damage = 0.0000001 * Energy released[tex]^(1.5)[/tex]
Substitute the value of energy released
Probability of lung hemorrhage = [tex]0.00014 * (3.31 * 10^9)^(0.684) = 0.38[/tex]
Probability of eardrum rupture = [tex]0.063 * (3.31 * 10^9)^(0.385) = 13.56[/tex]
Probability of glass breakage = [tex]0.005 * (3.31 * 10^9)^(0.5) = 291.24[/tex]
Probability of structural damage = [tex]0.0000001 * (3.31 * 10^9)^(1.5) = 3.12[/tex]
Therefore, the estimated probabilities of death due to lung hemorrhage, eardrum rupture, glass breakage, and structural damage are 0.38%, 13.56%, 291.24%, and 3.12%, respectively.
Learn more on hydrogen explosion on https://brainly.com/question/1561031
#SPJ4
Estimate the cost of expanding a planned new clinic by 8.4,000 ft2. The appropriate capacity exponent is 0.62, and the budget estimate for 185,000 ft2 was $19 million. (keep 3 decimals in your answer)
The capacity ratio method estimates the cost of expanding a clinic by 8,400 ft² by dividing the original facility's capacity by the new capacity. The new cost is approximately $23.314 million, reflecting larger facilities' lower per-unit costs and smaller facilities' higher costs.
To estimate the cost of expanding a planned new clinic by 8,400 ft², we can use the capacity ratio method.
Capacity Ratio Method: If the capacity of a facility changes by a factor of "C," the cost of the new facility will be "a" times the cost of the original facility, where "a" is the capacity exponent.
Capacity Ratio (C) = (New Capacity / Original Capacity)
New Cost = Original Cost x (Capacity Ratio)^Capacity Exponent
Given data:
Original Area = 185,000 ft²
New Area = 185,000 + 8,400 = 193,400 ft²
Capacity Ratio (C) = (193,400 / 185,000) = 1.0459
Capacity Exponent (a) = 0.62
Budget Estimate for 185,000 ft² = $19 million
New Cost = $19 million x (1.0459)^0.62= $19 million x 1.226= $23.314 million (approx)
Therefore, the estimated cost of expanding a planned new clinic by 8,400 ft² is $23.314 million (approx).
Note:In the capacity ratio method, the capacity exponent is used to adjust the cost estimate for a new facility to reflect the fact that larger facilities have lower per-unit costs, and smaller facilities have higher per-unit costs.
To know more about capacity ratio Visit:
https://brainly.com/question/14643660
#SPJ11
Which of the following gives the correct range for the graph? A coordinate plane with a segment going from the point negative 5 comma negative 2 to 0 comma negative 1 and another segment going from the point 0 comma negative 1 to 2 comma 3. −5 ≤ x ≤ 2 −5 ≤ y ≤ 2 −2 ≤ x ≤ 3 −2 ≤ y ≤ 3
The correct range for the graph is -5 ≤ x ≤ 2 and -2 ≤ y ≤ 3.
The correct range for the graph can be determined by identifying the minimum and maximum values for both the x and y coordinates of the points given.
Let's analyze the given segments:
1. The first segment goes from (-5, -2) to (0, -1).
- The x-coordinate ranges from -5 to 0.
- The y-coordinate ranges from -2 to -1.
2. The second segment goes from (0, -1) to (2, 3).
- The x-coordinate ranges from 0 to 2.
- The y-coordinate ranges from -1 to 3.
To find the overall range for the graph, we need to consider the combined range of both segments.
For the x-coordinate, the minimum value is -5 (from the first segment) and the maximum value is 2 (from the second segment). So, the correct range for the x-coordinate is -5 ≤ x ≤ 2.
For the y-coordinate, the minimum value is -2 (from the first segment) and the maximum value is 3 (from the second segment). So, the correct range for the y-coordinate is -2 ≤ y ≤ 3.
In summary:
- The x-coordinate ranges from -5 to 2.
- The y-coordinate ranges from -2 to 3.
This information provides the correct range for the graph.
For more such questions on range
https://brainly.com/question/28044915
#SPJ8
How can x + 2 = −3x + 11 be set up as a system of equations? (1 point)
Given equation:
x + 2 = −3x + 11
We can set up x + 2 = -3x + 11 as a system of equations by equating both sides by zero resulting in two equations.
The equations will be as followed:
x + 2 = 0 ............(1)
−3x + 11 = 0 ............(2)
Thus, x + 2 = −3x + 11 can be set up as a system of equations as x + 2 = 0 and −3x + 11 = 0.
PLEASE I NEED THIS QUICK!!!!!
Susan wants to make pumpkin bread and zucchini bread for the school bake sale. She has 15 eggs and 16 cups of flour in her pantry. Her recipe for one loaf of pumpkin bread uses 2 eggs and 3 cups of flour. Her recipe for one loaf of zucchini bread uses 3 eggs and 4 cups of flour. She plans to sell pumpkin bread loaves for $5 each and zucchini bread loaves for $4 each. Susan wants to maximize the money raised at the bake sale. Let x represent the number of loaves of pumpkin bread and y represent the number of loaves of zucchini bread Susan bakes.
What is the objective function for the problem?
P = 15x + 16y
P = 5x + 7y
P = 5x + 4y
P = 4x + 5y
The circumference, C, of a circle is Crd, where d is the diameter.
Solve Crd for d.
O A. d-
OB. d=C-n
O C. d-C
R
OD. d = nC
The correct answer is D. d = C / Cr. This means that the diameter, d, is equal to the circumference, C, divided by the product of C and r.
To solve the equation Crd for d, we need to isolate d on one side of the equation.
Given that C = Crd, we can divide both sides of the equation by Cr to obtain:
C / Cr = Crd / Cr
Simplifying the right side:
C / Cr = d
Therefore, the equation Crd for d simplifies to:
d = C / Cr
D is the right response because d = C / Cr. As a result, the circumference, C, divided by the sum of C and r's product equals the diameter, d.
for such more question on diameter
https://brainly.com/question/28700310
#SPJ8
Question in the picture:
The displacement vector of the airplane and the duration of the flight indicates that the direction and speed of the airplane are;
B. About 5.7° west of north at approximately 502.5 mph
What is a displacement vector?A displacement vector represents the change in location of an object.
The speed and direction of the airplane can be found from the resultant vector from point A to point C as follows;
A(20, 20), C(-30, 520)
The displacement vector from point A to point C is; C - A = (-30, 520) - (20, 20) = (-50, 500), which is the net displacement of the plane from 1 PM to 2 PM.
The direction of the plane, which is the angle between the y-axis and the displacement vector is; θ = arctan(50/500) ≈ 5.7°
The direction of the airplane is about 5.7° west of northThe magnitude of the displacement, which is the distance is therefore;
Distance = √((-50)² + (500)²) ≈ 502.5 miles
The speed = Distance/time
The time of flight from 1 PM to 2 PM = 1 hour
Therefore; Speed ≈ 502.5 miles/(1 hour) = 502.5 mphLearn more on displacement vector here: https://brainly.com/question/13265155
#SPJ1
Use the definition of the derivative to find the slope of the tangent line to the graph of the given function at any point. Show your work by completing the four-step process. (Simplify your answers completely for each step.) f(x) = 4x² + 7x Step 1: Step 2: Step 3: Step 4: f'(x) = lim h→0 f(x + h) = 4(x + h)² +7(x+h) f(x + h)-f(x) = h(4(2x+h)+7) f(x + h) − f(x) = h f(x+h)-f(x) h 4(2x+h) +7 8x + 7 X X (Expand your answer completely.) (Factor your answer completely.)
Let f(x) = x² + 5x. (a) Find the derivative f' off by using the definition of the derivative. Show your work by completing the four-step process. (Simplify your answers completely for each step.) f(x + h) = (x + h) +5(x+h) (b) Step 1: Step 2: Step 3: Step 4: f'(x) = _lim_ h→0 f(x +h)-f(x) = f(x+h)-f(x) h f(x +h)-f(x) h (Expand your answer completely.) X (Factor your answer completely.) Find an equation of the tangent line to the graph of f at the point (1,4). Give your answer in the slope-intercept form.
The equation of the tangent line to the graph of f at the point (1,4) is y = 15x - 11 in slope-intercept form.
Let's first find the derivative of the function f(x) = 4x² + 7x using the definition of the derivative.
Step 1: Find f(x + h)
f(x + h) = 4(x + h)² + 7(x + h)
= 4(x² + 2xh + h²) + 7x + 7h
= 4x² + 8xh + 4h² + 7x + 7h
Step 2: Find f(x)
f(x) = 4x² + 7x
Step 3: Find the difference f(x + h) - f(x)
f(x + h) - f(x) = (4x² + 8xh + 4h² + 7x + 7h) - (4x² + 7x)
= 8xh + 4h² + 7h
Step 4: Divide by h and take the limit as h approaches 0
f'(x) = lim(h→0) [f(x + h) - f(x)] / h
= lim(h→0) [(8xh + 4h² + 7h) / h]
= lim(h→0) [8x + 4h + 7]
= 8x + 7
So, the derivative of f(x) = 4x² + 7x is f'(x) = 8x + 7.
Now, let's find an equation of the tangent line to the graph of f at the point (1,4).
Using the point-slope form of a line, y - y₁ = m(x - x₁), where (x₁, y₁) is the point and m is the slope, we have:
y - 4 = (8(1) + 7)(x - 1)
y - 4 = (8 + 7)(x - 1)
y - 4 = 15(x - 1)
y - 4 = 15x - 15
y = 15x - 11
To learn more about derivative click here
brainly.com/question/29144258
#SPJ11
Solve x > 8 or x < 4.
Ø
{x | x > 12 or x < 6}
{x | x > 16/3 or x < 8/3}
Answer:
Step-by-step explanation:
The solution to the inequality x > 8 or x < 4 can be expressed as the set of all real numbers except for the interval [4, 8].
The solution to the inequality x > 12 or x < 6 can be expressed as the set of all real numbers.
The solution to the inequality x > 16/3 or x < 8/3 can be expressed as the set of all real numbers.
Mr. Halling and Mr. Clair were asked to help design a new
football field for Marist College. Mrs. Kessler said that the
width of the field needs to be 12 yards less than the length. Find
the area and perimeter of the field in terms of x.
How do I solve?
2. Determine the value of k when f(x)=2x¹ - 5x³+ Kx - 4 is divided by x-3, the remainder is 2.
The value of k when f(x) = 2x¹ - 5x³ + Kx - 4 is divided by x-3 and the remainder is 2, is K = 45.
To determine the value of k when f(x)=2x¹ - 5x³ + Kx - 4 is divided by x-3 and the remainder is 2, we can use the Remainder Theorem.
According to the Remainder Theorem, when a polynomial f(x) is divided by a linear factor x-a, the remainder is equal to f(a). In this case, the linear factor is x-3 and the remainder is 2.
So, to find the value of k, we substitute x=3 into the polynomial f(x) and set it equal to 2:
f(3) = 2(3)¹ - 5(3)³ + K(3) - 4 = 2
Now, let's solve for k:
2(3) - 5(3)³ + 3K - 4 = 2
6 - 135 + 3K - 4 = 2
-133 + 3K = 2
To isolate K, we add 133 to both sides:
3K = 2+ 133
3K = 135
Finally, divide both sides by 3 to solve for K:
K = 45
Learn more about remainder :
https://brainly.com/question/27749132
#SPJ11
Solve:
X+2
3
X-3 X-3
A x=7
B
C
+
X
1
D x= -7
3
The equation has no valid solution because it leads to a division by zero, resulting in an undefined expression.
To solve the equation, we need to find the value of x that satisfies the equation:
(x + 2)/(3(x - 3)) + (x + 1)/(3) = 0
To simplify the equation, we need to find a common denominator for the fractions. The common denominator is 3(x - 3):
[(x + 2)(x - 3)]/(3(x - 3)) + (x + 1)(x - 3)/(3(x - 3)) = 0
Expanding the numerators, we have:
[tex][(x^2 - x - 6) + (x^2 - 2x - 3)]/(3(x - 3)) = 0[/tex]
Combining like terms in the numerator, we get:
[tex](2x^2 - 3x - 9)/(3(x - 3)) = 0[/tex]
To solve for x, we set the numerator equal to zero:
[tex]2x^2 - 3x - 9 = 0[/tex]
This quadratic equation can be factored as:
(2x + 3)(x - 3) = 0
Setting each factor equal to zero, we get:
2x + 3 = 0 or x - 3 = 0
Solving each equation for x, we find:
2x = -3 or x = 3
Dividing both sides of the first equation by 2, we have:
x = -3/2
Therefore, the solutions to the equation are x = 3 and x = -3/2.
In the given options, the correct answer would be:
A. x = 7
None of the provided options matches the solutions obtained from solving the equation.
For similar question on equation.
https://brainly.com/question/29797709
#SPJ8
A steel framed arched hut, is used for storage, has a diameter of 16 feet and length of 48 feet, as shown in the picture below. The roof is made of aluminum. The aluminum costs 2.50 per square foot What will be the cost of the minimum amount needed to construct the roof
The cost of the minimum amount needed to construct the roof would be approximately $1256.
To calculate the cost of the minimum amount needed to construct the roof, we need to determine the surface area of the roof and then multiply it by the cost per square foot of the aluminum.
The roof of the hut can be approximated as a portion of a cylinder. The surface area of a cylinder can be calculated using the formula:
Surface Area = 2πrh + πr^2
Given that the diameter of the hut is 16 feet, the radius (r) is half of the diameter, which is 8 feet. The length of the hut is 48 feet.
Plugging these values into the formula, we get:
Surface Area = 2π(8)(48) + π(8)^2
Surface Area = 96π + 64π
Surface Area = 160π
Now, we need to multiply the surface area by the cost per square foot of aluminum, which is $2.50.
Cost = Surface Area * Cost per square foot
Cost = 160π * $2.50
To get an approximate numerical value, we can use the approximation π ≈ 3.14.
Cost = 160 * 3.14 * $2.50
Cost = $1256
Therefore, the cost of the minimum amount needed to construct the roof would be approximately $1256.
for such more question on cost
https://brainly.com/question/8993267
#SPJ8
Using induction, does the following statement hold: 1.1+2 2!++n.n!= (n+1)!-1 whenever n is a nonnegative integer? Yes No, basis step does not hold when n
No, inductive step does not hold because P(k) P(k+1)
Using induction, does the following statement hold: 1.1+2 2!++n.n!= (n+1)!-1. The statement holds for all nonnegative integers n. The correct option is Yes.
The statement holds when using induction.
Induction:
Step 1: Basis Step
If n = 0, then the left-hand side of the equation is 1.1! = 1, and the right-hand side is (0+1)!-1 = 0, so the statement is true for n=0.
Step 2: Inductive Hypothesis
Suppose the statement is true for n=k, that is,1.1+2 2!+3 3!+...+k k! = (k+1)!-1 (1)
Step 3: Inductive Step
We need to show that the statement is true for n=k+1. That is,1.1+2 2!+3 3!+...+(k+1) (k+1)! = [(k+1)+1]!-1(2)
To prove (2), we can add (k+1)(k+1)! to both sides of (1) to obtain1.1+2 2!+3 3!+...+k k!+(k+1)(k+1)! = (k+1)!-1+(k+1)(k+1)!
We can simplify the right-hand side using the distributive law, factoring out (k+1):= (k+2)!-1
The left-hand side is1.1+2 2!+3 3!+...+(k+1) (k+1)! =(k+1)!+(k+1)(k+1)! =(k+1)!(1+(k+1)) =(k+1)!(k+2)
Substituting the last two equations into (2) gives(k+1)!(k+2)-1 = (k+2)!-1
This is exactly the statement for n=k+1, so the inductive step is complete. Therefore, by the principle of mathematical induction, the statement holds for all nonnegative integers n. The correct option is Yes.
Learn more about nonnegative integers
https://brainly.com/question/10542824
#SPJ11
Write the coordinates of the vertices after a translation 5 units right.
Answer:
Let's assume the original shape was an equilateral triangle with vertices at (0,0), (1,2), (2,0).
After a translation 5 units right, the triangle's vertices will be at (5,0), (6,2), (7,0).
To explain, a translation is a transformation which moves a shape's location without rotating, reflecting, or resizing it. In this case, since the shape was translated 5 units right, each vertex moved 5 units right from its original position, so (0,0) became (5,0), (1,2) became (6,2), and (2,0) became (7,0).
Step-by-step explanation:
1.List four common corrections to a measurement made by a steel tape. How do you determine you add or subtract these from the measurements? 2. What is the distance from an IP (initial point) to the NE
1. Four common corrections to a measurement made by a steel tape are:
a) Temperature correction
b) Pull correction
c) Sag correction
d) Alignment correction
Temperature correction: The answer to temperature correction is that steel tapes expand or contract as the temperature changes and this change affects the accuracy of measurements. Therefore, temperature correction is done to compensate for the effect of the change of temperature.
Pulling correction: In order to get accurate measurements, the tape is always tensioned to an even pull or load while taking measurements. The main answer to pulling correction is that pulling a tape with too much force or with not enough force affects the measurement.
Sag correction: The main answer to sag correction is that the weight of the tape makes it bend and this affects the measurement. Therefore, sag correction is used to determine the amount of deviation caused by the weight of the tape.
Alignment correction: The main answer to alignment correction is that when measuring long distances, it is difficult to keep the tape straight which causes an error. Therefore, alignment correction is done to correct for these errors.2. The distance from an IP (initial point) to the NE can be found by using the bearing and distance. The main answer to this is that the bearing tells us the direction of the point we are measuring to and the distance gives us the length of the line from the IP to the NE.
To find the distance from the IP to the NE, we use the formula; Distance = Length × Cos Bearing Angle
Thus, Distance = 10,000 × Cos 25°. Therefore, the distance from the IP to the NE is 9,160 feet (approx).
Learn more about sag correction: https://brainly.com/question/33590303
#SPJ11
Problem 1 (15%). Given the function y₁ = x² is a solution to the differential equation x2y" - 3xy' + 4y = 0, find a second linearly independent solution y₂.
The second linearly independent solution is y₂ = x² ln x.
The given differential equation is x²y" - 3xy' + 4y = 0. Given y₁ = x² is a solution to the differential equation x²y" - 3xy' + 4y = 0. To find a second linearly independent solution y₂, we use the method of reduction of order.
Using Reduction of order method, we suppose a second solution as
y₂ = v(x) y₁ = x²
Then we have
y₂′ = 2xy₁′ + v′
y₂" = 2y₁′ + 2xy₁″ + v″
Substituting the above values in the given differential equation we get
x²(2y₁′ + 2xy₁″ + v″) − 3x(2xy₁′ + v′) + 4(x²)v(x) = 0
Simplify the above equation
2x³v″ + (2 − 6x²)v′ + 4x⁴v = 0
Dividing each term by x³, we get
v″ + (2 − 6x²/x³)v′ + 4x/v = 0
On simplifying we get
v″ + (2/x³)v′ − (6/x²)v′ + (4/x)v = 0
v″ + (2/x³)v′ − (6/x²)(2y₁′ + v′) + (4/x)v = 0
v″ − (12/x²)y₁′ + (4/x)v = 0
v″ − (12/x²)(2x) + (4/x)v = 0
v″ − 24/x + (4/x)v = 0
On solving the above differential equation we get the second solution
v(x) = x² ln x
Thus the second linearly independent solution is y₂ = x² ln x.
To know more about independent visit:
https://brainly.com/question/27765350
#SPJ11
1.Nickel has a face-centered cubic unit cell. The density of nickel is 6.84 g/cm^3. Calculate a value for the atomic radius of nickel.
2.A metallic solid with atoms in a face-centered cubic unit cell with an edge length of 392 pm has a density of 21.45 g/cm^3. Calculate the atomic mass and the atomic radius of the metal. Identify the metal.
1) The atomic radius of Nickel is: 0.52 µm
2) The atomic mass is 195 g/mol and radius is 139 pm and the element is Platinum(Pt))
How to calculate the atomic radius?1) The formula to calculate the atomic radius of nickel is expressed as:
Density = nM/(V*NA)
Where:
n is number of atoms per unit cell (4 for FCC)
M is atomic mass = 59 a m u
V is volume of the unit cell = a³
NA is avogadro's number = 6.02 * 10²³
6.84 = (4 * 59)/(a³ * 6.02 * 10²³)
a³ = (4 * 59)/(6.84 * 6.02 * 10²³)
a = 1.472 * 10⁻⁶ m
a = 1.472 µm
For FCC, a = 2√2r
Thus:
r = 1.472 µm/(2√2)
r = 0.52 µm
2) We are given:
a = 392 pm = 3.92 x 10⁻⁸ cm
ρ = 21.45 g/cm³
Thus:
V = (3.92 * 10⁻⁸)³
V = 6.024 * 10⁻²³ cm³
Thus:
21.45 = (4 * M)/(6.024 * 10⁻²³ * 6.02 * 10²³)
M = 195 g/mol
a = r√8
3.92 * 10⁻⁸ = r√8
r = 1.386 * 10⁻⁸cm = 139 pm
(Element with atomic mass 195 g/mol and radius = 139 pm (1.386x10⁻⁸cm) = Platinum(Pt)) = Platinum(Pt)
Read more about Atomic Radius at: https://brainly.com/question/15255548
#SPJ4
Sally wants to decreace 150 by 3%
What number would she get
Answer:
145.5
Step-by-step explanation:
cuz y not
Answer:
Hi there!! Thank you for posting this question, as it helped me figure this out for myself as well!!
Step-by-step explanation:
Maybe this will help,
Let’s pretend the actual number is 100. So, what is 3% of 100?
That is correct, it is 3.
And again, let’s pretend the number in question is actually 50, what is 3% of 50? Well, sense 50 is half of 100 let’s assume 3% of 50 would become Half of the 3 from earlier, making 50’s 3%, 2.5.
Let’s add those together, 3 + 2.5 = 5.5.
Therefore, if you decreased 150 by 3% you would arrive at 144.5.
I hope this helps!! I know this is not a very convention way to figure this out but I hope this makes sense!! Have a blessed day!!