The answers to the given questions are as follows:
a) The magnetic field 2 mm away from the centre of the capacitor 1 minute after the initial connection of the battery is 0.5 × 10⁻⁷ T·m/A.
b) The magnetic field 10 mm away from the centre of the capacitor 1 minute after the initial connection of the battery is 0.1 × 10⁻⁷ T·m/A.
To find the magnetic field inside the capacitor, we need to calculate the current flowing through the circuit first. Then, we can use Ampere's law to determine the magnetic field at specific distances.
Calculate the current:
The current in the circuit can be found using Ohm's law:
I = V / R,
where
I is the current,
V is the voltage, and
R is the resistance.
Given:
V = 10 volts,
R = 20 MQ (megaohms)
R = 20 × 10⁶ Ω.
Substituting the given values into the formula, we get:
I = 10 V / 20 × 10⁶ Ω
I = 0.5 × 10⁶ A
I = 0.5 μA.
Therefore, the current in the circuit 0.5 μA.
a) Calculate the magnetic field 2 mm away from the center:We can use Ampere's law to find the magnetic field at a distance of 2 mm away from the centre of the capacitor.
Ampere's law states that the line integral of the magnetic field around a closed loop is proportional to the current passing through the loop.
The equation for Ampere's law is:
∮B · dl = μ₀ × [tex]I_{enc}[/tex],
where
∮B · dl represents the line integral of the magnetic field B along a closed loop,
μ₀ is the permeability of free space = 4π × 10⁻⁷ T·m/A), and
[tex]I_{enc}[/tex] is the current enclosed by the loop.
In the case of a parallel plate capacitor, the magnetic field between the plates is zero. Therefore, we consider a circular loop of radius r inside the capacitor, and the current enclosed by the loop is I.
For a circular loop of radius r, the line integral of the magnetic field B along the loop can be expressed as:
∮B · dl = B × 2πr,
where B is the magnetic field at a distance r from the center.
Using Ampere's law, we have:
B × 2πr = μ₀ × I.
Substituting the given values:
B × 2π(2 mm) = 4π × 10⁻⁷ T·m/A × 0.5 μA.
Simplifying:
B × 4π mm = 2π × 10⁻⁷ T·m/A.
B = (2π × 10⁻⁷ T·m/A) / (4π mm)
B = 0.5 × 10⁻⁷ T·m/A.
Therefore, the magnetic field 2 mm away from the centre of the capacitor 1 minute after the initial connection of the battery is 0.5 × 10⁻⁷ T·m/A.
b) Calculate the magnetic field 10 mm away from the center:Using the same approach as above, we can find the magnetic field at a distance of 10 mm away from the centre of the capacitor.
B × 2π(10 mm) = 4π × 10⁻⁷ T·m/A × 0.5 μA.
Simplifying:
B × 20π mm = 2π × 10⁻⁷ T·m/A.
B = (2π × 10⁻⁷ T·m/A) / (20π mm)
B = 0.1 × 10⁻⁷ T·m/A.
Therefore, the magnetic field 10 mm away from the centre of the capacitor 1 minute after the initial connection of the battery is 0.1 × 10⁻⁷ T·m/A.
Learn more about Magnetic Field from the given link:
https://brainly.com/question/3033179
#SPJ11
An AC generator supplies an rms voltage of 240 V at 50.0 Hz. It is connected in series with a 0.250 H inductor, a 5.80 μF capacitor and a 286 Ω resistor.
What is the impedance of the circuit?
Tries 0/12 What is the rms current through the resistor?
Tries 0/12 What is the average power dissipated in the circuit?
Tries 0/12 What is the peak current through the resistor?
Tries 0/12 What is the peak voltage across the inductor?
Tries 0/12 What is the peak voltage across the capacitor?
Tries 0/12 The generator frequency is now changed so that the circuit is in resonance. What is that new (resonance) frequency?
The impedance of the circuit is approximately 287.6 Ω. The rms current through the resistor is approximately 0.836 A. The average power dissipated in the circuit is approximately 142.2 W. The peak current through the resistor is approximately 1.18 A. The peak voltage across the inductor is approximately 286.2 V. The peak voltage across the capacitor is approximately 286.2 V. The new resonance frequency of the circuit is 50.0 Hz.
To solve these problems, we'll use the formulas and concepts related to AC circuits.
1. Impedance (Z) of the circuit:
The impedance of the circuit is given by the formula:
Z = √(R^2 + (Xl - Xc)^2)
where R is the resistance, Xl is the inductive reactance, and Xc is the capacitive reactance.
Given:
R = 286 Ω
Xl = 2πfL = 2π(50.0 Hz)(0.250 H) ≈ 78.54 Ω
Xc = 1 / (2πfC) = 1 / (2π(50.0 Hz)(5.80 × 10^-6 F)) ≈ 54.42 Ω
Substituting the values into the formula, we get:
Z = √(286^2 + (78.54 - 54.42)^2)
≈ 287.6 Ω
Therefore, the impedance of the circuit is approximately 287.6 Ω.
2. RMS current through the resistor:
The rms current through the resistor can be calculated using Ohm's Law:
I = V / Z
where V is the rms voltage and Z is the impedance.
Given:
V = 240 V
Z = 287.6 Ω
Substituting the values into the formula, we have:
I = 240 V / 287.6 Ω
≈ 0.836 A
Therefore, the rms current through the resistor is approximately 0.836 A.
3. Average power dissipated in the circuit:
The average power dissipated in the circuit can be calculated using the formula:
P = I^2 * R
where I is the rms current and R is the resistance.
Given:
I = 0.836 A
R = 286 Ω
Substituting the values into the formula, we get:
P = (0.836 A)^2 * 286 Ω
≈ 142.2 W
Therefore, the average power dissipated in the circuit is approximately 142.2 W.
4. Peak current through the resistor:
The peak current through the resistor is equal to the rms current multiplied by √2:
Peak current = I * √2
Given:
I = 0.836 A
Substituting the value into the formula, we have:
Peak current = 0.836 A * √2
≈ 1.18 A
Therefore, the peak current through the resistor is approximately 1.18 A.
5. Peak voltage across the inductor and capacitor:
The peak voltage across the inductor and capacitor is equal to the rms voltage:
Peak voltage = V
Given:
V = 240 V
Substituting the value into the formula, we have:
Peak voltage = 240 V
≈ 240 V
Therefore, the peak voltage across the inductor and capacitor is approximately 240 V.
6. New resonance frequency:
In a resonant circuit, the inductive reactance (Xl) is equal to the capacitive reactance (Xc
To know more about impedance click here:
https://brainly.com/question/30887212
#SPJ11
In a region of space, a quantum particle with zero total energy has a wave functionψ(x) = Axe⁻ˣ²/L²
(b) Make a sketch of U(x) versus x .
To sketch U(x) versus x, we can plot the potential energy as a function of x using this equation. Keep in mind that the shape of the potential energy curve will depend on the values of the constants A, ħ, L, and m. The graph will show how the potential energy changes as the particle moves in the region of space.
The potential energy, U(x), of a quantum particle can be determined from its wave function, ψ(x). In this case, the wave function is given as ψ(x) = Axe⁻ˣ²/L², where A, x, and L are constants.
To sketch U(x) versus x, we need to find the expression for the potential energy. The potential energy is given by the equation U(x) = -ħ²(d²ψ/dx²)/2m, where ħ is the reduced Planck constant and m is the mass of the particle.
First, we need to find the second derivative of ψ(x). Taking the derivative of ψ(x) with respect to x, we get dψ/dx = A(e⁻ˣ²/L²)(-2x/L²). Taking the derivative again, we get [tex]d²ψ/dx² = A(e⁻ˣ²/L²)(4x²/L⁴ - 2/L²).[/tex]
Now, we can substitute the expression for the second derivative into the equation for the potential energy.
U(x) = -ħ²(d²ψ/dx²)/2m
= -ħ²A(e⁻ˣ²/L²)(4x²/L⁴ - 2/L²)/2m.
Remember to label the axes of your graph and include a key or legend if necessary.
To know more about potential energy visit:
https://brainly.com/question/24284560
#SPJ11
A battery of 15 volts is connected to a capacitor that stores 2 Coulomb of charge. What is the capacitance of the capacitor? (a) 7.5 F (b) 30 F (c) 0.13 F (d) not enough information
The capacitance of the capacitor is calculated to be approximately 0.13 Farads (F). This is determined based on a charge stored in the capacitor of 2 Coulombs (C) and a potential difference of 15 volts (V) applied across the capacitor (option c).
The capacitance of the capacitor can be calculated using the formula;
C = Q/V
Equation to calculate capacitance: The capacitance of the capacitor is directly proportional to the amount of charge stored per unit potential difference.
Capacitance of a capacitor can be defined as the ability of a capacitor to store electric charge. The unit of capacitance is Farad. One Farad is defined as the capacitance of a capacitor that stores one Coulomb of charge on applying one volt of potential difference. A battery of 15 volts is connected to a capacitor that stores 2 Coulomb of charge. We can calculate the capacitance of the capacitor using the formula above. C = Q/VC = 2/15 = 0.1333 F ≈ 0.13 F
The correct option is (c).
To know more about capacitance:
https://brainly.com/question/31871398
#SPJ11
1. Two lenses are placed along the x axis, with a diverging lens of focal length −7.70
cm on the left and a converging lens of focal length 17.0 cm on the right. When an object is placed 12.0 cm to the left of the diverging lens, what should the separation s of the two lenses be if the final image is to be focused at
x = [infinity]?
cm
2) An object has a height of 0.052 m and is held 0.230 m in front of a converging lens with a focal length of 0.140 m. (Include the sign of the value in your answers.)
(a) What is the magnification?
(b) What is the image height?
m
The magnification is 0.61. The image height is 0.0317 m, indicating that the image is smaller than the object's height.
To determine the separation s between the lenses, we can use the lens formula:
1/f_total = 1/f1 - 1/f2
where f_total is the effective focal length of the combination of lenses, f1 is the focal length of the diverging lens, and f2 is the focal length of the converging lens.
Plugging in the values, we have:
1/f_total = 1/-7.70 - 1/17.0
Solving for f_total, we get:
f_total = -26.7 cm
Since the final image is to be focused at x = infinity, the lenses need to be positioned such that the combined focal length is -26.7 cm. Therefore, the separation s between the lenses should also be 26.7 cm.
(a) The magnification (m) of an image formed by a lens is given by the formula:
m = -i/o
where i is the image distance and o is the object distance. The negative sign indicates that the image is inverted.
Plugging in the values, we have:
m = -(-0.140 m)/(0.230 m) = 0.61
Therefore, the magnification is 0.61, indicating that the image is reduced in size.
(b) The image height (h') can be calculated using the magnification formula:
h' = m * h
where h is the object height.
Plugging in the values, we have:
h' = 0.61 * 0.052 m = 0.0317 m
Therefore, the image height is 0.0317 m, indicating that the image is smaller than the object's height.
To learn more about focal length click here:
brainly.com/question/2194024
#SPJ11
A particle of mass 7.28 g moves at 3.68 km/s in an xy plane, in a region with a uniform magnetic field given by 6.43 i mT. At one instant, when the particle's velocity is directed 30.6 ° counterclockwise from the positive direction of the x axis, the magnetic force on the
particle is 0.458 € N. What is the particle's charge?
The particle's charge is approximately 19.35 milli-Coulombs (mC).
To find the particle's charge, we can use the equation for the magnetic force on a charged particle:
F = q * v * B * sin(theta)
Where:
F is the magnetic force,
q is the charge of the particle,
v is the velocity of the particle,
B is the magnetic field,
and theta is the angle between the velocity and the magnetic field.
We are given:
F = 0.458 € N,
v = 3.68 km/s = 3.68 * 10^3 m/s,
B = 6.43 * 10^(-3) T (since 1 mT = 10^(-3) T),
and theta = 30.6°.
Let's solve the equation for q:
q = F / (v * B * sin(theta))
Substituting the given values:
q = 0.458 € N / (3.68 * 10^3 m/s * 6.43 * 10^(-3) T * sin(30.6°))
Calculating:
q = 0.458 € N / (3.68 * 6.43 * sin(30.6°)) * 10^3 C
q ≈ 0.458 € N / (23.686) * 10^3 C
q ≈ 19.35 * 10^(-3) C
Therefore, the particle's charge is approximately 19.35 milliCoulombs (mC).
Learn more about magnetic force
https://brainly.com/question/10353944
#SPJ11
BIO Predict/Calculate A Tongue’s Acceleration When a cha-meleon captures an insect, its tongue can extend 16 cm in 0.10 s. (a) Find the magnitude of the tongue’s acceleration, assuming it to be constant. (b) In the first 0.050 s, does the tongue extend 8.0 cm, more than 8.0 cm, or less than 8.0 cm? (c) Find the extension of the tongue in the first 5s.
To determine the magnitude of a chameleon's tongue acceleration, as well as the extension of the tongue over a given time interval, we can utilize kinematic equations. Given that the tongue extends 16 cm in 0.10 s, we can calculate its acceleration using the equation of motion:
(a) To find the magnitude of the tongue's acceleration, we can use the equation of motion: Δx = v0t + (1/2)at^2, where Δx is the displacement, v0 is the initial velocity (assumed to be zero in this case), t is the time, and a is the acceleration. Rearranging the equation, we have a = 2(Δx) / t^2. Substituting the given values, we get a = 2(16 cm) / (0.10 s)^2. By performing the calculations, we can determine the magnitude of the tongue's acceleration.
(b) To determine if the tongue extends more than, less than, or exactly 8.0 cm in the first 0.050 s, we can use the equation of motion mentioned earlier. We plug in Δx = v0t + (1/2)at^2 and the given values of v0, t, and a. By calculating Δx, we can compare it to 8.0 cm to determine the tongue's extension during that time interval.
(c) To find the extension of the tongue in the first 5 s, we can use the equation of motion again. By substituting v0 = 0, t = 5 s, and the previously calculated value of a, we can calculate the tongue's extension over the given time period.
In summary, we can use the equations of motion to determine the magnitude of a chameleon's tongue acceleration when it captures an insect. Additionally, we can calculate the extension of the tongue during specified time intervals.
Learn more about magnitude here :
brainly.com/question/28173919
#SPJ11
A 20.0 kg object starts from rest and slides down an inclined plane. The change in its elevation is 3.0 m and its final speed is 6 m/sec. How much energy did the object lose due to friction as it slid down the plane?
The object lost 228 J of energy due to friction as it slid down the inclined plane.
To find the energy lost due to friction as the object slides down the inclined plane, we need to calculate the initial mechanical energy and the final mechanical energy of the object.
The initial mechanical energy (Ei) is given by the potential energy at the initial height, which is equal to the product of the mass (m), acceleration due to gravity (g), and the initial height (h):
Ei = m * g * h
The final mechanical energy (Ef) is given by the sum of the kinetic energy at the final speed (KEf) and the potential energy at the final height (PEf):
Ef = KEf + PEf
The kinetic energy (KE) is given by the formula:
KE = (1/2) * m * v^2
where m is the mass and v is the velocity.
The potential energy (PE) is given by the formula:
PE = m * g * h
Given:
Mass of the object (m) = 20.0 kg
Change in elevation (h) = 3.0 m
Final speed (v) = 6 m/s
[tex]\\ΔE = Ei - Ef\\ΔE = 588 J - 360 J\\ΔE = 228 J[/tex]
Next, let's calculate the final mechanical energy (Ef):
The energy lost due to friction (ΔE) can be calculated as the difference between the initial mechanical energy and the final mechanical energy:
[tex]ΔE = Ei - Ef\\ΔE = 588 J - 360 J\\ΔE = 228 J[/tex]
Therefore, the object lost 228 J of energy due to friction as it slid down the inclined plane.
Learn more about friction
https://brainly.com/question/28356847
#SPJ11
Two blocks with masses 0.325 kg (A) and 0.884 kg (B) sit on a frictionless surface. Between them is a spring with spring constant 28.5 N/m, which is not attached to either block The two blocks are pushed together, compressing the spring by 0.273 meter, after which the system is released from rest. What is the final speed of the block A? (Hint: you will need to use both conservation of energy and conservation of momentum to solve this problem).
The final speed of block A is approximately 1.48 m/s. To determine the final speed of block A, we can apply the principles of conservation of mechanical energy.
First, let's calculate the potential energy stored in the compressed spring:
Potential energy (PE) = 0.5 * k * x^2
Where k is the spring constant and x is the compression of the spring. Substituting the given values:
PE = 0.5 * 28.5 N/m * (0.273 m)^2 = 0.534 J
Since the system is released from rest, the initial kinetic energy is zero. Therefore, the total mechanical energy of the system remains constant throughout.
Total mechanical energy (E) = PE
Now, let's calculate the final kinetic energy of block A:
Final kinetic energy (KE) = E - PE
Since the total mechanical energy remains constant, the final kinetic energy of block A is equal to the potential energy stored in the spring:
Final kinetic energy (KE) = 0.534 J
Finally, using the kinetic energy formula:
KE = 0.5 * m * v^2
Where m is the mass of block A and v is its final speed. Rearranging the formula:
v = sqrt(2 * KE / m)
Substituting the values for KE and m:
v = sqrt(2 * 0.534 J / 0.325 kg) ≈ 1.48 m/s
Therefore, the final speed of block A is approximately 1.48 m/s.
Learn more about spring constant here:
brainly.com/question/3148447
#SPJ11
A superconducting solenoid with 2000 turns/m is meant to generate a magnetic field of 12.0 T. Calculate the current required. KA (+ 0.02 kA)
The current required to generate a magnetic field of 12.0 T in a superconducting solenoid with 2000 turns/m is approximately 6.0 kA.
To calculate the current, we can use Ampere's Law, which states that the magnetic field (B) inside a solenoid is directly proportional to the product of the current (I) and the number of turns per unit length (N).
B = μ₀ * N * I
where μ₀ is the permeability of free space (4π × 10⁻⁷ T·m/A).
Rearranging the equation to solve for current (I):
I = B / (μ₀ * N)
Plugging in the given values:
I = 12.0 T / (4π × 10⁻⁷ T·m/A * 2000 turns/m)
I ≈ 6.0 kA
learn more about Ampere's Law, here:
https://brainly.com/question/32676356
#SPJ11
Consider two different media, one water and the other unknown. With them, it is determined that the critical angle is 55° What is the refractive index of this unknown medium?
The refractive index of the unknown medium is approximately 1.758. The answer is arrived at using the formula n2 = sin (critical angle) x n1.
The critical angle is determined by the equation:sin (critical angle) = n2/n1, where n1 and n2 are the refractive indices of the media.Therefore, the refractive index of the unknown medium is given by the equation:n2 = sin (critical angle) x n1. Given that the critical angle is 55° and n1 is the refractive index of water, which is 1.33, we can determine the refractive index of the unknown medium as follows:n2 = sin (critical angle) x n1 = sin (55°) x 1.33 ≈ 1.758 (to three significant figures). Therefore, the refractive index of the unknown medium is approximately 1.758.
The refractive index of the unknown medium can be determined when the critical angle and refractive index of another medium (in this case, water) is known.
To know more about refractive index visit:
brainly.com/question/30761100
#SPJ11
How much power is necessary to produce a sound wave with an
intensity of 0.693 W/m2 when the wave front is vibrating
an area of 2.16 m2?
1.47 W
3.12 W
0.321 W
1.50 W
The power required to produce a sound wave with an intensity of 0.693 W/m2 when the wave front is vibrating an area of 2.16 m2 is 1.50 W.Given,Intensity of the sound wave = I = 0.693 W/m2Vibration area of the wave front = A = 2.16 m2The formula to calculate the power of sound wave isP = I * A
Where,P = Power of sound waveI = Intensity of sound waveA = Vibration area of the wave frontBy putting the given values in the above formula, we getP = 0.693 W/m2 * 2.16 m2P = 1.50 W
Therefore, the power required to produce a sound wave with an intensity of 0.693 W/m2 when the wave front is vibrating an area of 2.16 m2 is 1.50 W.
For more questions like Intensity click the link below:
brainly.com/question/28448844
#SPJ11
An automobile traveling 76.0 km/h has tires of 70.0 cm diameter. (a) What is the angular speed of the tires about their axles? (b) If the car is brought to a stop uniformly in 39.0 complete turns of the tires, what is the magnitude of the angular acceleration of the wheels? (c) How far does the car move during the braking? (
(a) Angular speed: 60.3 rad/s
(b) Angular acceleration: 0.244 rad/s²
(c) Distance moved: 5182.4 meters
(a) To find the angular speed of the tires about their axles, we can use the formula:
Angular speed (ω) = Linear speed (v) / Radius (r)
First, let's convert the speed from km/h to m/s:
76.0 km/h = (76.0 km/h) * (1000 m/km) * (1/3600 h/s) ≈ 21.1 m/s
The radius of the tire is half of its diameter:
Radius (r) = 70.0 cm / 2 = 0.35 m
Now we can calculate the angular speed:
Angular speed (ω) = 21.1 m/s / 0.35 m ≈ 60.3 rad/s
Therefore, the angular speed of the tires about their axles is approximately 60.3 rad/s.
(b) To find the magnitude of the angular acceleration of the wheels, we can use the formula:
Angular acceleration (α) = Change in angular velocity (Δω) / Time (t)
The change in angular velocity can be found by subtracting the initial angular velocity (ω_i = 60.3 rad/s) from the final angular velocity (ω_f = 0 rad/s), as the car is brought to a stop:
Δω = ω_f - ω_i = 0 rad/s - 60.3 rad/s = -60.3 rad/s
The time (t) is given as 39.0 complete turns of the tires. One complete turn corresponds to a full circle, or 2π radians. Therefore:
Time (t) = 39.0 turns * 2π radians/turn = 39.0 * 2π rad
Now we can calculate the magnitude of the angular acceleration:
Angular acceleration (α) = (-60.3 rad/s) / (39.0 * 2π rad) ≈ -0.244 rad/s²
The magnitude of the angular acceleration of the wheels is approximately 0.244 rad/s².
(c) To find the distance the car moves during the braking, we can use the formula:
Distance (d) = Linear speed (v) * Time (t)
The linear speed is given as 21.1 m/s, and the time is the same as calculated before:
Time (t) = 39.0 turns * 2π radians/turn = 39.0 * 2π rad
Now we can calculate the distance:
Distance (d) = 21.1 m/s * (39.0 * 2π rad) ≈ 5182.4 m
Therefore, the car moves approximately 5182.4 meters during the braking.
To learn more about angular acceleration, Visit:
https://brainly.com/question/13014974
#SPJ11
A certain freely falling object, released from rest, requires 1.35 s to travel the last 40.0 m before it hits the ground. (a) Find the velocity of the object when it is 40.0 m above the ground. (Indicate the direction with the sign of your answer. Let the positive direction be upward.) m/s (b) Find the total distance the object travels during the fall.
The velocity of the object when it is 40.0 m above the ground is approximately -29.6 m/s, with the negative sign indicating downward direction.
To find the velocity of the object when it is 40.0 m above the ground, we can use the kinematic equation:
v^2 = u^2 + 2as
where v is the final velocity, u is the initial velocity (which is 0 m/s as the object is released from rest), a is the acceleration due to gravity (-9.8 m/s^2), and s is the displacement (40.0 m).
Plugging in the values, we have:
v^2 = 0^2 + 2 * (-9.8) * 40.0
v^2 = -2 * 9.8 * 40.0
v^2 = -784
v ≈ ± √(-784)
Since the velocity cannot be imaginary, we take the negative square root:
v ≈ -√784
v ≈ -28 m/s
Therefore, the velocity of the object when it is 40.0 m above the ground is approximately -28 m/s, indicating a downward direction.
(b) The total distance the object travels during the fall can be calculated by finding the sum of the distances traveled during different time intervals. In this case, we have the distance traveled during the last 1.35 seconds before hitting the ground.
The distance traveled during the last 1.35 seconds can be calculated using the equation:
s = ut + (1/2)at^2
where s is the distance, u is the initial velocity (0 m/s), a is the acceleration due to gravity (-9.8 m/s^2), and t is the time (1.35 s).
Plugging in the values, we have:
s = 0 * 1.35 + (1/2) * (-9.8) * (1.35)^2
s = -6.618 m
Since the distance is negative, it indicates a downward displacement.
The total distance traveled during the fall is the sum of the distances traveled during the last 40.0 m and the distance calculated above:
Total distance = 40.0 m + (-6.618 m)
Total distance ≈ 33.382 m
Therefore, the total distance the object travels during the fall is approximately 33.382 meters.
To learn more about velocity
brainly.com/question/30559316
#SPJ11
12 A car travels in a straight line at speed v along a horizontal road. The car moves
against a resistive force F given by the equation
F = 400+kv²
where F is in newtons, v in ms-1 and k is a constant.
At speed v = 15ms-1, the resistive force F is 1100 N.
a
Calculate, for this car:
i the power necessary to maintain the speed of 15ms-¹,
ii the total resistive force at a speed of 30 ms-¹,
iii the power required to maintain the speed of 30ms-¹.
Answer:
i) Power = Force * Velocity = 1100 * 15 = 16500 W = 16.5 kW(ii) Find the value of k first: F = 400 + k(15^2) k = 28/9 F = 400 +(28/9)(30^2) = 320
Explanation:
One of the fundamental forces of nature is the strong nuclear force. This force is responsible for a) Keeping electrons from falling into the nucleus b) Keeping the particles in the nucleus together c) Transforming particles via radioactive decay d) Sticking atoms together to form molecules
The strong nuclear force is responsible for keeping the particles in the nucleus together. So the answer is b. The strong nuclear force is the strongest of the four fundamental forces of nature.
The strong nuclear force is the strongest of the four fundamental forces of nature. It is responsible for holding the protons and neutrons in the nucleus of an atom together. The strong nuclear force is much stronger than the electromagnetic force, which is responsible for holding electrons in orbit around the nucleus.
The strong nuclear force is a short-range force, which means that it only works over very small distances. This is why the protons and neutrons in the nucleus are able to stay together, even though they are positively charged and repel each other.
The strong nuclear force is also a very attractive force, which means that it pulls the protons and neutrons together very strongly. This is why the nucleus is so stable.
The other three fundamental forces of nature are the electromagnetic force, the weak nuclear force, and gravity. The electromagnetic force is responsible for holding electrons in orbit around the nucleus, as well as for many other phenomena, such as magnetism and light. The weak nuclear force is responsible for radioactive decay, and gravity is responsible for the attraction between objects with mass.
To learn more about nuclear force click here
https://brainly.com/question/19271485
#SPJ11
What is the critical angle for light going from ethanol to air? Submit Answer Incorrect. Tries 1/40 Previous Tries
The critical angle for light going from ethanol to air the critical angle for light going from ethanol to air is approximately 48.6 degrees.
To calculate the critical angle for light going from ethanol to air, we need to use Snell's law, which relates the angles of incidence and refraction for light traveling between two different media. Snell's law is given by:
n₁ * sin(θ₁) = n₂ * sin(θ₂)
Where:
n₁ is the refractive index of the initial medium (ethanol)
n₂ is the refractive index of the final medium (air)
θ₁ is the angle of incidence
θ₂ is the angle of refraction
The critical angle occurs when the angle of refraction is 90 degrees (light travels along the boundary). So we can rewrite Snell's law as:
n₁ * sin(θ_c) = n₂ * sin(90)
Since sin(90) = 1, the equation simplifies to:
n₁ * sin(θ_c) = n₂
To find the critical angle (θ_c), we need to know the refractive indices of ethanol and air. The refractive index of ethanol (n₁) is approximately 1.36, and the refractive index of air (n₂) is approximately 1.
Plugging in the values, we get:
1.36 * sin(θ_c) = 1
Now, we can solve for the critical angle:
sin(θ_c) = 1 / 1.36
θ_c = arcsin(1 / 1.36)
Using a calculator, we find:
θ_c ≈ 48.6 degrees
Therefore, the critical angle for light going from ethanol to air is approximately 48.6 degrees.
To know more about ethanol refer here:
https://brainly.com/question/29294678#
#SPJ11
3. What would happen if you put an object at the focal point of the lens? 4. What would happen if you put an object at the focal point of the mirror? 5. What would happen if you put an object between the focal point and the lens? 6. What would happen if you put an object between the focal point and the mirror?
The specific placement of an object relative to the focal point of a lens or mirror determines the characteristics of the resulting image, such as its nature (real or virtual), size, and orientation.
Let's provide a more detailed explanation for each scenario:
3. Placing an object at the focal point of a lens:
When an object is placed exactly at the focal point of a lens, the incident rays from the object become parallel to each other after passing through the lens. This occurs because the lens refracts (bends) the incoming rays in such a way that they converge at the focal point on the opposite side. However, when the object is positioned precisely at the focal point, the refracted rays become parallel and do not converge to form a real image. Therefore, in this case, no real image is formed on the other side of the lens.
4. Placing an object at the focal point of a mirror:
If an object is positioned at the focal point of a mirror, the reflected rays will appear to be parallel to each other. This happens because the light rays striking the mirror surface are reflected in a way that they diverge as if they were coming from the focal point behind the mirror. Due to this divergence, the rays never converge to form a real image. Instead, the reflected rays appear to originate from a virtual image located at infinity. Consequently, no real image can be projected onto a screen or surface.
5. Placing an object between the focal point and the lens:
When an object is situated between the focal point and a converging lens, a virtual image is formed on the same side as the object. The image appears magnified and upright. The lens refracts the incoming rays in such a way that they diverge after passing through the lens. The diverging rays extend backward to intersect at a point where the virtual image is formed. This image is virtual because the rays do not actually converge at that point. The virtual image is larger in size than the object, making it appear magnified.
6. Placing an object between the focal point and the mirror:
Similarly, when an object is placed between the focal point and a concave mirror, a virtual image is formed on the same side as the object. The virtual image is magnified and upright. The mirror reflects the incoming rays in such a way that they diverge after reflection. The diverging rays appear to originate from a point behind the mirror, where the virtual image is formed. Again, the virtual image is larger than the object and is not a real convergence point of light rays.
In summary, the placement of an object relative to the focal point of a lens or mirror determines the behavior of the light rays and the characteristics of the resulting image. These characteristics include the nature of the image (real or virtual), its size, and its orientation (upright or inverted).
Note: In both cases (5 and 6), the images formed are virtual because the light rays do not actually converge or intersect at a point.
To learn more about focal point, Visit:
https://brainly.com/question/30761313
#SPJ11
1. (5 pts.) A 25 g cylinder of metal at a temperature of 120°C is dropped into 200 g of water at 10°C. The container is a perfect insulator, so no energy is lost to the environment. The specific heat of the cylinder is 280 J/kg/K. a. What is the equilibrium temperature of the system? b. What is the change in entropy of the system?
a. The equilibrium temperature of the system is approximately 34.8°C.
b. The change in entropy of the system is positive.
a. To find the equilibrium temperature of the system, we can use the principle of energy conservation. The heat lost by the metal cylinder is equal to the heat gained by the water. The heat transfer can be calculated using the equation:
Q = m1 * c1 * (T f - Ti)
where Q is the heat transferred, m1 is the mass of the metal cylinder, c1 is the specific heat of the cylinder, T f is the final temperature (equilibrium temperature), and Ti is the initial temperature.
The heat gained by the water can be calculated using the equation:
Q = m2 * c2 * (T f - Ti)
where m2 is the mass of the water, c2 is the specific heat of water, T f is the final temperature (equilibrium temperature), and Ti is the initial temperature.
Setting these two equations equal to each other and solving for T f:
m1 * c1 * (T f - Ti1) = m2 * c2 * (T f - Ti2)
(25 g) * (280 J/kg/K) * (T f - 120°C) = (200 g) * (4.18 J/g/K) * (T f - 10°C)
Simplifying the equation:
(7 T f - 8400) = (836 T f - 8360)
Solving for T f:
836 T f - 7 T f = 8360 - 8400
829 T f = -40
T f ≈ -0.048°C ≈ 34.8°C
Therefore, the equilibrium temperature of the system is approximately 34.8°C.
b. The change in entropy of the system can be calculated using the equation:
ΔS = Q / T
where ΔS is the change in entropy, Q is the heat transferred, and T is the temperature.
Since the container is a perfect insulator and no energy is lost to the environment, the total heat transferred in the system is zero. Therefore, the change in entropy of the system is also zero.
a. The equilibrium temperature of the system is approximately 34.8°C.
b. The change in entropy of the system is zero.
To know more about entropy ,visit:
https://brainly.com/question/419265
#SPJ11
Pressure is the force applied perpendicular to the surface of an object per unit area over which that force distributed. So is the ratio of a vector quantity to scalar quantity. Why it is not vector quantity
**Pressure is not a vector quantity** because it does not have both magnitude and direction. While pressure involves the application of a force on a surface, the resulting pressure itself is solely determined by the magnitude of the force and the area over which it is distributed.
Pressure is defined as the force per unit area, and it is represented by a scalar value. Scalars only have magnitude and no direction. In contrast, vector quantities, such as force and velocity, have both magnitude and direction. Thus, pressure lacks a directional component and is considered a scalar quantity.
Learn more about pressure here:-
brainly.com/question/30351725
#SPJ11
Two positive charges \( \mathrm{Q} 1 \) and \( \mathrm{Q} 2 \) are separated by a distance \( r \). The charges repel each other with a force \( F \). If the magnitude of each charge is doubled and th
If the magnitude of each charge is doubled and the distance between them is halved, the new force between them will be four times the original force.
Let's denote the original charges as Q1 and Q2, and the original force as F. The electric force between two charges is given by Coulomb's law:
F = k * (Q1 * Q2) / r^2, where k is the Coulomb's constant and r is the distance between the charges.
If the magnitude of each charge is doubled (2Q1 and 2Q2) and the distance between them is halved (r/2), the new force (F') can be calculated as:
F' = k * (2Q1 * 2Q2) / (r/2)^2.
Simplifying the equation:
F' = k * (4Q1 * 4Q2) / (r/2)^2,
F' = k * (16Q1 * Q2) / (r^2/4),
F' = k * (16Q1 * Q2) * (4/r^2),
F' = 64 * k * (Q1 * Q2) / r^2.
Therefore, the new force between the charges is four times the original force: F' = 4F.
To learn more about magnitude click here.
brainly.com/question/30033702
#SPJ11
Arescue helicopter is lifting a man (weight - 705.717994328948 N) from a capsized boat by means of a cable and harness. (a) What is the tension in the cable when the man is given an initial upward acceleration of 2.01 m/s?? (b) What is the tension during the remainder of the rescue when he is pulled upward at a constant velocity?
The tension during the remainder of the rescue when he is pulled upward at a constant velocity is 705.717994328948 N
The tension in the cable during this phase is equal to the weight of the man:
Tension = Weight
= 705.717994328948 N
(a) To determine the tension in the cable when the man is given an initial upward acceleration of 2.01 m/s², we need to consider the forces acting on the man.
When the man is initially accelerated upward, the net force acting on him is given by Newton's second law:
Net force = mass * acceleration
The weight of the man is acting downward, opposing the upward force applied by the helicopter. So, the equation becomes:
Tension - Weight = mass * acceleration
where Tension is the tension in the cable, Weight is the weight of the man, mass is the mass of the man (Weight divided by gravitational acceleration), and acceleration is the given upward acceleration.
Weight = 705.717994328948 N
acceleration = 2.01 m/s²
gravitational acceleration (g) ≈ 9.8 m/s²
First, let's calculate the mass of the man:
mass = Weight / g
= 705.717994328948 N / 9.8 m/s²
Now we can substitute the values into the equation:
Tension - Weight = mass * acceleration
Tension - 705.717994328948 N = (705.717994328948 N / 9.8 m/s²) * 2.01 m/s²
Simplifying and solving for Tension:
Tension = (705.717994328948 N / 9.8 m/s²) * 2.01 m/s² + 705.717994328948 N
(b) During the remainder of the rescue when the man is pulled upward at a constant velocity, the net force acting on the man is zero. This means the upward force applied by the helicopter (tension) equals the weight of the man.
Therefore,
During this stage, the cable's tension is equivalent to the man's weight:
Weight x Tension = c
Please note that due to rounding errors, the final values may vary slightly.
learn more about velocity from given link
https://brainly.com/question/21729272
#SPJ11
The diameter of an oxygen (02) molecule is approximately 0.300 nm.
For an oxygen molecule in air at atmospheric pressure and 18.3°C, estimate the total distance traveled during a 1.00-s time interval.
The actual distance traveled by the molecule in a straight line will be much smaller than 484 meters.
The mean free path of a gas molecule is the average distance it travels between collisions with other molecules. At atmospheric pressure and 18.3°C, the mean free path of an oxygen molecule is approximately 6.7 nm.
During a 1.00-s time interval, an oxygen molecule will travel a distance equal to the product of its speed and the time interval. The speed of an oxygen molecule at atmospheric pressure and 18.3°C can be estimated using the root-mean-square speed equation:
[tex]v_{rms}[/tex] = √(3kT/m)
where k is Boltzmann's constant, T is the temperature in Kelvin, and m is the mass of the molecule.
For an oxygen molecule, [tex]k = 1.38 * 10^{-23}[/tex] J/K, T = 291.45 K (18.3°C + 273.15), and [tex]m = 5.31 * 10^{-26}[/tex] kg.
Plugging in the values, we get:
[tex]v_{rms} = \sqrt {(3 * 1.38 * 10^{-23} J/K * 291.45 K / 5.31 * 10^{-26} kg)} = 484 m/s[/tex]
Therefore, during a 1.00-s time interval, an oxygen molecule will travel approximately:
distance = speed * time = 484 m/s * 1.00 s ≈ 484 meters
However, we need to take into account that the oxygen molecule will collide with other molecules in the air, and its direction will change randomly after each collision. The actual distance traveled by the molecule in a straight line will be much smaller than 484 meters, and will depend on the number of collisions it experiences during the time interval. Therefore, the estimate of the total distance traveled by an oxygen molecule in air during a 1.00-s time interval should be considered a very rough approximation.
Learn more about "Distance travelled by the molecule" : https://brainly.com/question/29409777
#SPJ11
Question 1 of 7 > 0% What is the cylinder's speed u at the bottom of the ramp? 0 U= Resources Hint A uniform, solid cylinder of radius 7.00 cm and mass 5.00 kg starts from rest at the top of an inclined plane that is 2.00 m long and tilted at an angle of 25.0" with the horizontal. The cylinder rolls without slipping down the ramp.
The cylinder's speed at the bottom of the ramp is 3.08 m/s.
The gravitational potential energy of the cylinder is given by mgh, where m is the mass of the cylinder, g is the acceleration due to gravity, and h is the height of the cylinder above the ground. The rotational kinetic energy of the cylinder is given by 1/2Iω^2, where I is the moment of inertia of the cylinder and ω is the angular velocity of the cylinder.
The moment of inertia of a solid cylinder about its axis of rotation is given by I = 1/2MR^2, where M is the mass of the cylinder and R is the radius of the cylinder. The angular velocity of the cylinder is given by ω = v/R, where v is the linear velocity of the center of mass of the cylinder.
Substituting these equations into the conservation of energy equation, we get:
[tex]mgh = 1/2I\omega ^2[/tex]
[tex]mgh = 1/2(1/2MR^2)(v/R)^2[/tex]
[tex]mgh = 1/4MR^2v^2[/tex]
Solving for v, we get:
[tex]v = \sqrt{ (2gh/R)}[/tex]
In this case, we have:
m = 5.00 kg
g = 9.80 m/s^2
h = 2.00 m
R = 7.00 cm = 0.0700 m
Substituting these values into the equation for v, we get:
[tex]v = \sqrt{(2(9.80 m/s^2)(2.00 m)/(0.0700 m))} = 3.08 m/s[/tex]
Therefore, the cylinder's speed at the bottom of the ramp is 3.08 m/s.
To learn more about conservation of energy here brainly.com/question/29220242
#SPJ11
On a marimba (Fig. P18.63), the wooden bar that sounds a tone when struck vibrates in a transverse standing wave having three antinodes and two nodes. The lowest frequency note is 87.0 Hz , produced by a bar 40.0cm long.(a) Find the speed of transverse waves on the bar.
The speed of transverse waves on the bar is 696 cm/s.
The speed of transverse waves on the bar can be found using the formula v = [tex]fλ[/tex], where v is the velocity, f is the frequency, and [tex]λ[/tex]is the wavelength.
To find the wavelength, we can use the relationship between the number of antinodes and nodes in a standing wave. In this case, we have three antinodes and two nodes.
In a transverse standing wave, the number of nodes and antinodes is related to the number of half-wavelengths that fit on the length of the bar. Since we have two nodes and three antinodes, there are five half-wavelengths on the bar.
Knowing that the bar length is 40.0 cm, we can calculate the wavelength by dividing the length by the number of half-wavelengths:
[tex]λ[/tex]= (40.0 cm) / (5 half-wavelengths)
= 8.0 cm.
Now we can substitute the values into the formula:
v = (87.0 Hz) * (8.0 cm)
= 696 cm/s.
Therefore, the speed of transverse waves on the bar is 696 cm/s.
To know more about velocity visit:
https://brainly.com/question/18084516
#SPJ11
A car moving at 38 km/h negotiates a 160 m -radius banked turn
designed for 60 km/h. What coefficient of friction is needed to
keep the car on the road?
we need to find the value of What coefficient of friction is needed to keep the car on the road. The concepts we can use are centripetal force, gravity etc.
Given data:
The speed of the car v = 38 km/h
Radius of the turn r = 160 m
The turn is designed for the speed of the car v' = 60 km/h
The coefficient of friction between the tires and the road = μ
First, we convert the speed of the car into m/s.1 km/h = 0.27778 m/s
Therefore, 38 km/h = 38 × 0.27778 m/s = 10.56 m/s
Similarly, we convert the speed designed for the turn into m/s
60 km/h = 60 × 0.27778 m/s
60 km/h = 16.67 m/s
To keep the car on the road, the required centripetal force must be provided by the frictional force acting on the car. The maximum frictional force is given by μN, where N is the normal force acting on the car. To find N, we use the weight of the car, which is given by mg where m is the mass of the car and g is the acceleration due to gravity, which is 9.81 m/s². We assume that the car is traveling on a level road. So, N = mg. We can find the mass of the car from the centripetal force equation. The centripetal force acting on the car is given by F = mv²/r where m is the mass of the car, v is the velocity of the car, and r is the radius of the turn. We know that the required centripetal force is equal to the maximum frictional force that can be provided by the tires. Therefore,
F = μN
F = μmg
So,
mv²/r = μmg
m = μgr/v²
Now we can substitute the values in the above formula to calculate the required coefficient of friction.
μ = mv²/(gr)
μ = v²/(gr) × m = (10.56)²/(160 × 9.81)
μ = 0.205
So, the required coefficient of friction to keep the car on the road is μ = 0.205.
to know more about coefficient of friction visit:
brainly.com/question/29281540
#SPJ11
A group of astronauts wish to know the gravitational acceleration of a newly discovered planet. On the surface of the planet, they construct a simple pendulum of length 21.0 m. The pendulum yields a 18.7 s period of oscillation. Part 1 Find the gravitational acceleration of the planet. Part 2 How much stronger is earth's gravitational acceleration compared to this planet?
The gravitational acceleration on Earth is 4.56 times stronger than the newly discovered planet and 2) the gravitational acceleration of the newly discovered planet is 2.15 m/s².
Part 1- The time period of a simple pendulum is given by the following formula:
T=2π√(L/g) where T is the time period, L is the length of the pendulum and g is the gravitational acceleration.
Let g1 be the gravitational acceleration of the newly discovered planet.
We know that the length of the pendulum is L= 21.0 m and the time period of oscillation of the pendulum is T= 18.7s.
Substituting these values in the formula, we get:
18.7=2π√(21.0/g1)
Squaring both sides of the equation, we get:
g1=(4π²×21.0)/18.7² = 2.15 m/s²
Therefore, the gravitational acceleration of the newly discovered planet is 2.15 m/s².
Part 2- Let g2 be the gravitational acceleration of Earth.
The acceleration due to gravity on the surface of the Earth is g2 = 9.81 m/s².
Comparing the gravitational acceleration of Earth to that of the newly discovered planet, we have:
The ratio of the gravitational acceleration of Earth to that of the newly discovered planet = g2/g1
= 9.81 m/s²/2.15 m/s² = 4.56
Therefore, the gravitational acceleration on Earth is 4.56 times stronger than the newly discovered planet.
know more about gravitational
https://brainly.com/question/3009841
#SPJ11
You lean against a table such that your weight exerts a force F on the edge of the table that is directed at an angle 0 of 17.0° below a line drawn parallel to the table's surface. The table has a mass of 35.0 kg and the coefficient of static friction between its feet and the ground is 0.550. What is the maximum force Fmax with which you can lean against the tab
The maximum force (Fmax) with which one can lean against a table, considering a table mass of 35.0 kg and a coefficient of static friction of 0.550 between its feet and the ground, is approximately 321.5 Newtons. This force is exerted at an angle of 17.0° below a line parallel to the table's surface.
To determine the maximum force Fmax with which you can lean against the table, we need to consider the equilibrium conditions and the maximum static friction force.
First, let's analyze the forces acting on the table. The weight of the table (mg) acts vertically downward, where m is the mass of the table and g is the acceleration due to gravity.
The normal force exerted by the ground on the table (N) acts vertically upward, perpendicular to the table's surface.
When you lean against the table, you exert a force F at an angle θ of 17.0° below the line parallel to the table's surface.
This force has a vertical component Fv = F × sin(θ) and a horizontal component Fh = F × cos(θ).
For the table to remain in equilibrium, the vertical forces must balance: N - mg - Fv = 0. Solving for N, we get N = mg + Fv.
The maximum static friction force between the table's feet and the ground is given by f_s = μ_s × N, where μ_s is the coefficient of static friction.
To find the maximum force Fmax, we need to determine the value of N and substitute it into the expression for f_s:
N = mg + Fv = mg + F × sin(θ)
f_s = μ_s × (mg + F × sin(θ))
For maximum Fmax, the static friction force must be at its maximum, which occurs just before sliding or when f_s = μ_s × N.
Therefore, Fmax = (μ_s × (mg + F × sin(θ))) / cos(θ).
We can now substitute the given values: m = 35.0 kg, θ = 17.0°, μ_s = 0.550, and g = 9.8 m/s² into the equation to find Fmax.
Fmax = (0.550 × (35.0 × 9.8 + F × sin(17.0°))) / cos(17.0°)
Now, let's calculate the value of Fmax using this equation.
Using a numerical calculation, the value of Fmax comes out to be approximately 321.5 Newtons.
Therefore, the maximum force (Fmax) with which you can lean against the table is approximately 321.5 Newtons.
To know more about force refer here:
https://brainly.com/question/30000060#
#SPJ11
How much work is done on the gas in the process as shown, in Joules? Vf = 94 cm3.(1.00 cm3 = 1.00×10-6 m3, 1.00 kPa = 1.00×103 Pa.)
Your answer needs to have 2 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement.
The work done on the gas in the process shown is approximately -3.5 × 10⁻³ Joules.
Given: Vi = 40.0 cm³ = 40.0 × 10⁻⁶ m³
Vf = 94 cm³ = 94 × 10⁻⁶ m³
P = 101 k
Pa ΔV = Vf - Vi
= 94 × 10⁻⁶ - 40.0 × 10⁻⁶
= 54.0 × 10⁻⁶ m³
By the ideal gas law,
PV = nRTHere, n, R, T are constantn = number of moles of the gas R = gas constant
T = temperature of the gas in kelvin
Assuming that the temperature of the gas remains constant during the process, we get,
P₁V₁ = P₂V₂or, P₁V₁ = P₂(V₁ + ΔV)or, P₂ = P₁V₁ / (V₁ + ΔV)
= 101 × 40.0 × 10 / (40.0 + 54.0) × 10⁻⁶
= 65.1 kPa
Work done on the gas, w = -PΔV= -65.1 × 54.0 × 10⁻⁶
= -3.52 × 10⁻³ ≈ -3.5 × 10⁻³
The work done on the gas in the process shown is approximately -3.5 × 10⁻³ Joules.
Learn more about ideal gas law,
brainly.com/question/30458409
#SPJ11
The position of a body is given by x(t) = t2-4t+9. What is the body's acceleration at t = 0?
The speed of a body is given by v(t) = 2t. How far has the body moved from t = 0 to t = 1?
We drop a rock from a height of 3.0 meters above the ground. At what speed does the stone hit the ground?
We throw a stone straight up, the stone comes 12m up. How long did the stone take up?
The body's acceleration at t = 0, we substitute t = 0 into the expression for acceleration: a(0) = 2. And The distance traveled by the body from t = 0 to t = 1, we need to integrate the speed function over the given time interval. Also, The speed at which the rock hits the ground when dropped from a height of 3.0 meters, is 1.566 seconds to reach a height of 12 m.
To find the body's acceleration at t = 0, we need to differentiate the position function x(t) with respect to time: x(t) = t^2 - 4t + 9
Differentiating x(t) with respect to t, we get:
v(t) = 2t
Differentiating v(t) with respect to t again, we find the acceleration function:
a(t) = 2
Therefore, the body's acceleration at t = 0 is 2.
To find how far the body has moved from t = 0 to t = 1, we need to integrate the speed function v(t) over the interval [0, 1]:
v(t) = 2t
Integrating v(t) with respect to t, we get the displacement function:
s(t) = t^2
To find the distance traveled from t = 0 to t = 1, we evaluate the displacement function at t = 1 and subtract the displacement at t = 0:
s(1) - s(0) = 1^2 - 0^2 = 1 - 0 = 1
Therefore, the body has moved 1 unit of distance from t = 0 to t = 1.
When a rock is dropped from a height of 3.0 meters above the ground, its initial velocity is 0 m/s. Using the equation of motion:
v^2 = u^2 + 2as
where v is the final velocity, u is the initial velocity, a is the acceleration due to gravity (-9.8 m/s^2), and s is the displacement.
We have:
v = ?
u = 0 m/s
a = -9.8 m/s^2
s = -3.0 m (negative because the displacement is downward)
Plugging in the values, we can solve for the final velocity:
v^2 = (0 m/s)^2 + 2(-9.8 m/s^2)(-3.0 m)
v^2 = 0 + 58.8
v = √58.8 ≈ 7.67 m/s
Therefore, the stone hits the ground with a speed of approximately 7.67 m/s.
To determine the time it takes for the stone to reach a height of 12 m, we can use the equation of motion:
s = ut + (1/2)at^2
where s is the displacement, u is the initial velocity, a is the acceleration due to gravity (-9.8 m/s^2), and t is the time.
We have:
s = 12 m
u = ?
a = -9.8 m/s^2
t = ?
At the highest point, the velocity is 0 m/s, so u = 0 m/s.
Plugging in the values, we can solve for the time:
12 m = 0 m/s * t + (1/2)(-9.8 m/s^2)(t^2)
12 m = -4.9 m/s^2 * t^2
t^2 = -12 m / -4.9 m/s^2
t^2 ≈ 2.449 s^2
t ≈ √2.449 ≈ 1.566 s
Therefore, the stone takes approximately 1.566 seconds to reach a height of 12 m.
To learn more about, velocity, click here, https://brainly.com/question/30559316
#SPJ11
a 190-lb man carries a 20-lb can of paint up a helical staircase that encircles a silo with radius 15 ft. if the silo is 80 ft high and the man makes exactly four complete revolutions, how much work is done by the man against gravity in climbing to the top?
The work done by the man against gravity in climbing to the top is 9,480 foot-pounds.
To calculate the work done by the man, we need to determine the total change in potential energy as he climbs up the helical staircase that encircles the silo. The potential energy can be calculated using the formula PE = mgh, where m represents the mass, g represents the acceleration due to gravity, and h represents the height.
In this case, the mass of the man is 190 lb, and the height of the silo is 80 ft. Since the man makes exactly four complete revolutions around the silo, we can calculate the circumference of the helical staircase. The circumference of a circle is given by the formula C = 2πr, where r represents the radius. In this case, the radius of the silo is 15 ft.
To find the work done against gravity, we need to multiply the change in potential energy by the number of revolutions. The change in potential energy is obtained by multiplying the mass, the acceleration due to gravity (32.2 ft/s²), and the height. The number of revolutions is four.
Therefore, the work done by the man against gravity in climbing to the top can be calculated as follows:
Work = 4 * m * g * h
= 4 * 190 lb * 32.2 ft/s² * 80 ft
= 9,480 foot-pounds.
Learn more about Work
brainly.com/question/18094932
#SPJ11