The angle of rotation in the shaft, in the positive direction, is approximately 0.000149 radians
The angle of rotation in the shaft can be calculated using the formula: θ = T * L / (G * π * r^4)
where:
θ is the angle of rotation in radians,
T is the torque applied to one end of the shaft (6 Nm),
L is the length of the shaft (1.3 m),
G is the shear modulus of the metal (16,174 MPa), and
r is the radius of the shaft (half of the diameter, which is 26 mm / 2 = 13 mm = 0.013 m).
First, let's convert the units of the torque from Nm to Nmm since the shear modulus is given in MPa.
6 Nm * 1000 = 6000 Nmm
Now, let's calculate the radius: r = 0.013 m
Next, let's substitute the values into the formula: θ = (6000 Nmm) * (1.3 m) / (16174 MPa * π * (0.013 m)^4)
Calculating this expression gives: θ ≈ 0.000149 radians
Learn more about shear modulus:
https://brainly.com/question/14020225
#SPJ11
An unidentified compound contains 29.84g of sodium, 67.49g of chromium, and 72.67g of oxygen. What is the empirical formula of the compound?
The empirical formula of the compound is Na₂Cr₂O₇.
We must identify the simplest whole-number ratio of the components in order to obtain the empirical formula of the compound. Finding the moles of each element and dividing them by the least mole value will enable us to do this.
Mass sodium (Na) = 29.84 g
Mass chromium (Cr) = 67.49 g
Mass oxygen (O) = 72.67 g
Utilizing the molar masses of each element, calculate its moles.
Molar mass Na = 22.99 g/mol
Molar mass Cr = 52.00 g/mol
Molar mass O = 16.00 g/mol
Moles Na = Mass of Na / Molar mass of Na
= 29.84 g / 22.99 g/mol
≈ 1.298 mol
Moles Cr = Mass fCr / Molar mass Cr
= 67.49 g / 52.00 g/mol
≈ 1.296 mol
Moles O = Mass O / Molar mass O
= 72.67 g / 16.00 g/mol
≈ 4.542 mol
By the smallest mole value, divide the moles. By dividing all moles by the smallest mole value, 1.296, we arrive at roughly:
Na: 1.298 / 1.296 ≈ 1
Cr: 1.296 / 1.296 = 1
O: 4.542 / 1.296 ≈ 3.5
The ratios are approximately 1:1:3.5. To obtain whole numbers, we multiply all values by 2:
Na: 2
Cr: 2
O: 7
so it's gonna be Na₂Cr₂O₇
To know more about empirical formula, visit:
brainly.com/question/32125056
#SPJ11
A small cylinder of hellum gas used for filling balloons has a volume of 2.50 L and a pressure of 1920 atm at 25∘C. Part A How many balloons can you fill if each one has a volume of 1.40 L and a pressure of 1.30 atm at 25 ∘C ?
3,606 balloons can be filled. A small cylinder of hellum gas used for filling balloons has a volume of 2.50 L and a pressure of 1920 atm at 25∘C. 3,606 balloons can be fill if each one has a volume of 1.40 L and a pressure of 1.30 atm at 25 ∘C.
Given data: Volume of helium gas = 2.50 L Pressure of helium gas = 1920 atm
Temperature of helium gas = 25 degree C Volume of each balloon = 1.40 L Pressure of each balloon = 1.30 atm Temperature of each balloon = 25 degree C
First of all, we will calculate the number of moles of helium gas using the ideal gas law
PV = nRT1920 atm × 2.50 L = n × 0.0821 L atm/(mol K) × (25 + 273) Kn = (1920 atm × 2.50 L)/(0.0821 L atm/(mol K) × 298 K)≈ 204.78 mol
Now, we will calculate the number of balloons that can be filled using the ideal gas lawPV = nRT
For one balloon, the volume and pressure are given. We need to find the number of moles of helium gas present in one balloon using the ideal gas law 1.30 atm × 1.40 L = n × 0.0821 L atm/(mol K) × (25 + 273) Kn = (1.30 atm × 1.40 L)/(0.0821 L atm/(mol K) × 298 K)≈ 0.0568 mol
Number of balloons = Number of moles of helium gas present in the cylinder/Number of moles of helium gas present in each balloon= 204.78 mol/0.0568 mol≈ 3,606 balloons
Therefore, 3,606 balloons can be filled.
To know more about small cylinder visit:
brainly.com/question/19756733
#SPJ11
In the accompanying diagram, what is sin E?
Please see image below (math)
Answer:
[tex]\sin E=\dfrac{4}{5}[/tex]
Step-by-step explanation:
To find the value of sin E we can use the sine trigonometric ratio.
[tex]\boxed{\begin{minipage}{9 cm}\underline{Sine trigonometric ratio} \\\\$\sf \sin(\theta)=\dfrac{O}{H}$\\\\where:\\ \phantom{ww}$\bullet$ $\theta$ is the angle. \\ \phantom{ww}$\bullet$ $\sf O$ is the side opposite the angle. \\\phantom{ww}$\bullet$ $\sf H$ is the hypotenuse (the side opposite the right angle). \\\end{minipage}}[/tex]
From inspection of the given right triangle:
The angle is E, so θ = E.The side opposite angle E is FG, so O = 4.The hypotenuse of the triangle is EF, so H = 5.Substitute these values into the sine ratio:
[tex]\sin E=\dfrac{4}{5}[/tex]
A wine-dispensing system uses argon canisters to pressurize and preserve wine in the bottle. An argon canister for the system has a volume of 55.0 mL and contains 26.0 g of argon. Assuming ideal gas behavior, what is the pressure (in atm) in the canister at 22.0°C ? Pressure of canister: When the argon is released from the canister, it expands to fill the wine bottle. How many 750.0−mL wine bottles can be purged with the argon in the canister at a pressure of 1.20 atm and a temperature of 22.0°C ? Wine bottle count:
According to the ideal gas law, PV = nRT, pressure, volume, number of moles, and temperature are related to each other by the ideal gas constant (R). P = nRT/V, where n is the number of moles, R is the ideal gas constant, T is the temperature in Kelvin, and V is the volume. Let us first convert the volume of the canister from milliliters (mL) to liters (L):55.0 mL × (1 L/1000 mL) = 0.0550 L
Next, we need to calculate the number of moles of argon in the canister. We can use the molar mass of argon to convert from grams to moles:26.0 g Ar × (1 mol Ar/39.95 g Ar)
= 0.651 mol Ar Now we can use the ideal gas law to solve for pressure:P
= nRT/V
= (0.651 mol)(0.0821 L atm/mol K)(295 K)/(0.0550 L)
≈ 2.81 atm
Let's first convert the volume of a wine bottle from milliliters (mL) to liters (L):750.0 mL × (1 L/1000 mL) = 0.7500 LNext, let's convert the temperature to Kelvin:22.0°C + 273
= 295 KNow we can solve for the number of moles of argon required to fill a wine bottle at 1.20 atm and 295 K:P
= nRT/Vn
= PV/RT
= (1.20 atm)(0.7500 L)/(0.0821 L atm/mol K)(295 K)
≈ 0.0368 mol Ar Finally, we can use the number of moles in the canister to determine the maximum number of bottles that can be purged:n
= 0.651 mol Ar × (1 bottle/0.0368 mol Ar)
≈ 17.7 bottles (rounded down to the nearest whole number) Pressure of canister:
≈ 2.81 atm; Wine bottle count: 17
To know more about temperature, visit:
https://brainly.com/question/7510619
#SPJ11
A 9 ft slide will be installed on a playground. The top of the slide will be 7 ft above the ground. What angle does the slide make with the ground? Enter your answer in the box. Round your final answer to the nearest degree.
The angle that the slide makes with the ground is approximately 40.6 degrees when rounded to the nearest degree.
To find the angle that the slide makes with the ground, we can use basic trigonometric principles.
In this case, we have a right triangle formed by the slide, the ground, and a vertical line connecting the top of the slide to the ground.
The height of the slide is given as 7 ft, and the length of the slide is given as 9 ft.
We can use the trigonometric function tangent (tan) to calculate the angle.
The tangent of an angle is defined as the ratio of the opposite side to the adjacent side in a right triangle.
In this case, the opposite side is the height of the slide (7 ft), and the adjacent side is the length of the slide (9 ft).
Using the formula for tangent, we can calculate the angle:
tan(angle) = opposite/adjacent
tan(angle) = 7/9
To find the angle, we need to take the inverse tangent (arctan) of this ratio:
angle = arctan(7/9)
Using a calculator or a trigonometric table, we can find the angle to be approximately 40.6 degrees.
For similar question on right triangle.
https://brainly.com/question/2217700
#SPJ8
Answer the below Question: What is the nature of the bonding in C_3H_2Cl2, Is it polar? A. Submit your drawing with dipole moments B. Identify the molecules polarity c. Identify the molecules geometries
The given compound is C3H2Cl2, which is known as Dichloroacetylene. The nature of the bonding in C3H2Cl2 is polar bonding. The nature of the bond is polar because there is an unequal distribution of electrons among the atoms due to the electronegativity difference between Carbon (2.55), Chlorine (3.16), and Hydrogen (2.2).
It has a triple bond between the carbon atoms and has chlorine atoms on both sides. Therefore, the geometry of the molecule is linear. A linear molecule has a bond angle of 180 degrees. In the molecule, the difference in electronegativity between carbon and hydrogen causes a bond polarity that exists between carbon and chlorine. A polar bond is formed when there is an electronegativity difference between the two atoms, resulting in the unequal sharing of electrons, which causes a partial positive charge on one end and a partial negative charge on the other end.
The molecule is polar and has a dipole moment. The dipole moment of a molecule is a vector quantity that measures the separation of charges in a molecule. Polarity: As stated earlier, the molecule is polar. In general, the polarity of a molecule is determined by the electronegativity difference between the atoms and the molecular geometry. Geometry: The geometry of the molecule is linear. It has a triple bond between the carbon atoms and has chlorine atoms on both sides. Therefore, the geometry of the molecule is linear. A linear molecule has a bond angle of 180 degrees.
To know more about unequal visit:
https://brainly.com/question/15577133
#SPJ11
Declaring variables - Declare two integer variables x and y, - Assign them any values. - Print addition/subtraction/multiplication and division of these two variables on to the screen
Submission Task (- Grade 1%) Follow the same steps asin Exercise 2, but change the step 2 to ask the user for input forthese values by using Scanner class.
Two integer variables x and y, prompts the user to enter values for them using the Scanner class, and performs addition, subtraction, multiplication, and division operations on those variables:
import java.util.Scanner;
public class VariableOperations {
public static void main(String[] args) {
Scanner scanner = new Scanner(System.in);
System.out.print("Enter the value for x: ");
int x = scanner.nextInt();
System.out.print("Enter the value for y: ");
int y = scanner.nextInt();
// Addition
int addition = x + y;
System.out.println("Addition: " + addition);
// Subtraction
int subtraction = x - y;
System.out.println("Subtraction: " + subtraction);
// Multiplication
int multiplication = x * y;
System.out.println("Multiplication: " + multiplication);
// Division
if (y != 0) {
double division = (double) x / y;
System.out.println("Division: " + division);
} else {
System.out.println("Cannot divide by zero.");
}
}
}
This code prompts the user to enter values for x and y, performs the four basic arithmetic operations, and displays the results on the screen.
Learn more about variables here:
https://brainly.com/question/29696241
#SPJ11
Each molecule listed contains an expanded octet (10 or 12
electrons) around the central atom. Write the Lewis structure for
each molecule.
(a) ClF5
(b) SF6
(c) IF5
The Lewis structures for the molecules are:
(a) ClF5: F-Cl-F-F-F
(b) SF6: F-S-F-F-F-F
(c) IF5: F-I-F-F-F
To write the Lewis structure for each molecule with an expanded octet, we need to determine the number of valence electrons for each atom and distribute them around the central atom, following the octet rule.
(a) ClF5:
- Chlorine (Cl) has 7 valence electrons, and fluorine (F) has 7 valence electrons.
- Since there are 5 fluorine atoms bonded to the central chlorine atom, we have a total of 5 × 7 = 35 valence electrons from the fluorine atoms.
- Adding the 7 valence electrons from the chlorine atom, we have a total of 42 valence electrons.
- To distribute the electrons, we place the chlorine atom in the center and surround it with the five fluorine atoms.
- Initially, we place one electron pair (two electrons) between each bonded atom.
- This leaves us with 42 - 10 = 32 valence electrons remaining.
- To complete the octets for each atom, we place 3 lone pairs (6 electrons) on the central chlorine atom and 1 lone pair (2 electrons) on each fluorine atom.
- The Lewis structure for ClF5 is:
F
|
F - Cl - F
|
F
(b) SF6:
- Sulfur (S) has 6 valence electrons, and each fluorine (F) atom has 7 valence electrons.
- Since there are 6 fluorine atoms bonded to the central sulfur atom, we have a total of 6 × 7 = 42 valence electrons from the fluorine atoms.
- Adding the 6 valence electrons from the sulfur atom, we have a total of 48 valence electrons.
- To distribute the electrons, we place the sulfur atom in the center and surround it with the six fluorine atoms.
- Initially, we place one electron pair (two electrons) between each bonded atom.
- This leaves us with 48 - 12 = 36 valence electrons remaining.
- To complete the octets for each atom, we place 3 lone pairs (6 electrons) on the central sulfur atom and 1 lone pair (2 electrons) on each fluorine atom.
- The Lewis structure for SF6 is:
F
|
F - S - F
|
F
(c) IF5:
- Iodine (I) has 7 valence electrons, and each fluorine (F) atom has 7 valence electrons.
- Since there are 5 fluorine atoms bonded to the central iodine atom, we have a total of 5 × 7 = 35 valence electrons from the fluorine atoms.
- Adding the 7 valence electrons from the iodine atom, we have a total of 42 valence electrons.
- To distribute the electrons, we place the iodine atom in the center and surround it with the five fluorine atoms.
- Initially, we place one electron pair (two electrons) between each bonded atom.
- This leaves us with 42 - 10 = 32 valence electrons remaining.
- To complete the octets for each atom, we place 3 lone pairs (6 electrons) on the central iodine atom and 1 lone pair (2 electrons) on each fluorine atom.
- The Lewis structure for IF5 is:
F
|
F - I - F
|
F
Remember that Lewis structures are a simplified representation of molecular bonding and electron distribution. They provide a useful visual tool for understanding the arrangement of atoms and electrons in a molecule.
To learn more about Lewis structures visit : https://brainly.com/question/20300458
#SPJ11
Question : 13 What is a feature found in all ortho-para directing groups? A. The atom attached to the aromatic ring possesses an unshared pair of electrons. VB. The group has the ability to delocalize the positive charge of the arenium ion. C. The atom directly attached to the aromatic ring is more electronegative than carbon.
In all ortho-para directing groups, the atom attached to the aromatic ring possesses an unshared pair of electrons. The ortho-para directing groups in organic chemistry refer to a group of functional groups that have the ability to direct substitution reactions towards either ortho or para positions in the aromatic ring.
The mechanism behind this behavior is attributed to the resonance or inductive effects of the substituent functional group.The ortho-para directing groups, unlike meta-directing groups, don't block the substitution reaction of the aromatic ring. They favor substitution at ortho and para positions of the ring. The feature common to all ortho-para directing groups is that the atom directly attached to the aromatic ring has a lone pair of electrons. This property allows them to stabilize positive charges generated on the aromatic ring during substitution reactions.
Hence, they direct the substitution reaction towards the ortho- or para-position. For instance, in nitrobenzene, the nitro group directs the incoming electrophile towards the ortho and para position as the nitrogen atom attached to the aromatic ring has a lone pair of electrons.
To know more about aromatic ring visit:-
https://brainly.com/question/31554111
#SPJ11
Answer:
C. The atom directly attached to the aromatic ring is more electronegative than carbon.
Step-by-step explanation:
In ortho-para directing groups, the atom directly attached to the aromatic ring is more electronegative than carbon. This electronegativity difference creates a polar bond, which allows for efficient delocalization of the positive charge in the arenium ion. This polarization facilitates the stabilization of positive charge and makes the ortho and para positions more favorable for electrophilic aromatic substitution reactions.
To know more about Polar Bond
https://brainly.in/question/56891399
#SPJ11
Problem 1 Any vertical curve with G2>G1 is a sag curve. TRUE or FALSE Problem 2 The selection of minimum length for a crest vertical curve is controlled by 4 criteria: SSD, Comfort, General appearance and Drainage control. TRUE or FALSE
Any vertical curve with G2>G1 is a sag curve. The given statement is TRUE. he selection of minimum length for a crest vertical curve is controlled by 4 criteria: SSD, Comfort, General appearance and Drainage control. The given statement is FALSE
Problem 1: Any vertical curve with G2>G1 is a sag curve. The given statement is TRUE. This statement states that any vertical curve with G2 > G1 is a sag curve. It is because a sag curve is a vertical curve where the curve's tangent angle is greater than the grade or slope of the curve.
Problem 2: The selection of minimum length for a crest vertical curve is controlled by 4 criteria: SSD, Comfort, General appearance and Drainage control. The given statement is FALSE. The selection of the minimum length for a crest vertical curve is not controlled by four criteria; instead, it is controlled by three criteria. The three criteria are sight distance, headlight sight distance, and stopping sight distance.
The stopping sight distance is the most crucial criteria that must be met when selecting the minimum length of the crest vertical curve.The stopping sight distance is the minimum length of the crest vertical curve. It is calculated by using the following formula:s = (V²/2gf) + (V/2a) + dwhere, V is the design speed of the vehicleg is the gravitational constantf is the friction factor of the roada is the deceleration rate of the vehicled is the height difference between the driver's eye and the road. The answer is FALSE.
Learn more about vertical curve
https://brainly.com/question/15274197
#SPJ11
10
be
=1
90 cm
b
Save answer
=1
el
54 cm
el
=1
19
20
1
What is the length of the missing leg? 1cessary, round to the nearest tenth.
centimeters
o
G
6
22 23
4
24
25
26
The length of the missing leg is approximately 72 centimeters.
To find the length of the missing leg, we can use the Pythagorean theorem.
According to the given information, we have a right triangle with two known sides:
One leg: 90 cm
Hypotenuse: 54 cm
Let's denote the missing leg as "x" cm.
The Pythagorean theorem states that the square of the hypotenuse is equal to the sum of the squares of the other two sides.
Therefore, we can set up the following equation:
[tex]90^2 + x^2 = 54^2[/tex]
Simplifying the equation, we have:
[tex]8100 + x^2 = 2916[/tex]
Subtracting 2916 from both sides:
[tex]x^2 = 8100 - 2916[/tex]
[tex]x^2 = 5184[/tex]
Taking the square root of both sides:
x = √5184
x ≈ 72 cm (rounded to the nearest tenth)
For similar question on length.
https://brainly.com/question/31511655
#SPJ8
Part A) Draw the shear diagram for the beam. Follow the sign
convention.
Part B) Draw the moment diagram for the beam. Follow the sign
convention.
We draw Part A) the shear diagram for the beam following the sign convention. Part B) the moment diagram for the beam following the sign convention.
Part A) To draw the shear diagram for the beam, we need to follow the sign convention. The sign convention for shear forces is positive when they cause clockwise rotation and negative when they cause counterclockwise rotation.
1. Start by locating the support reactions. If the beam is simply supported, there will be an upward reaction at one end and a downward reaction at the other end.
2. Begin plotting the shear diagram from left to right. At the left end of the beam, the shear force will be equal to the reaction at that end.
3. Move along the beam and consider the forces acting on it. If there are concentrated loads or moments, make sure to include their effects on the shear force.
4. At each point where there is a concentrated load or moment, make a jump in the shear force equal to the magnitude of that load or moment.
5. Continue this process until you reach the other end of the beam, and plot the final shear force there.
Part B) The moment diagram for the beam can be drawn by following the same sign convention. The sign convention for moments is positive when they cause sagging (concave up) and negative when they cause hogging (concave down).
1. Start plotting the moment diagram from left to right. At the left end of the beam, the moment will be zero.
2. Move along the beam and consider the forces acting on it. If there are concentrated loads or moments, make sure to include their effects on the moment.
3. At each point where there is a concentrated load or moment, make a jump in the moment equal to the magnitude of that load or moment.
4. If there are distributed loads, calculate the area under the shear diagram within that segment of the beam. This area represents the change in moment.
5. Continue this process until you reach the other end of the beam, and plot the final moment there.
By following these steps and considering the sign convention, you can accurately draw the shear diagram and moment diagram for a beam.
Learn more about the shear diagram from the given link-
https://brainly.com/question/30355350
#SPJ11
Calculate the amount of current need to deposit 2.4g of copper onto the cathode of a Cu/CuSO4 half-cell if the process is to be completed in 1 hr. What is this process called?
To deposit 2.4g of copper in 1 hour onto the cathode, approximately 2.032 A of current (I) is required in the electrolysis process known as electrodeposition of copper.
To calculate the amount of current needed to deposit 2.4g of copper onto the cathode in 1 hour, we can use Faraday's law of electrolysis.
1. Determine the molar mass of copper (Cu). It is 63.55 g/mol.
2. Convert the mass of copper (2.4g) to moles by dividing it by the molar mass: 2.4g / 63.55 g/mol = 0.0378 mol.
3. Since the reaction is Cu²⁺(aq) + 2e⁻ -> Cu(s), we can see that 2 moles of electrons are required to produce 1 mole of copper. Therefore, 0.0378 mol of copper will require 0.0378 x 2 = 0.0756 moles of electrons.
4. Calculate the charge (Q) required to deposit this amount of copper by multiplying the number of moles of electrons (0.0756) by Faraday's constant (F = 96,485 C/mol): Q = 0.0756 mol x 96,485 C/mol = 7,317.1 C.
5. Finally, calculate the current (I) by dividing the charge (Q) by the time (t) in seconds (1 hour = 3600 seconds): I = Q / t = 7,317.1 C / 3600 s ≈ 2.032 A.
The process is called electrolysis, specifically the electrodeposition of copper.
Learn more About electrodeposition from the given link
https://brainly.com/question/14778783
#SPJ11
Positive term series (don't need solution to 7)
A positive term series is a sequence of numbers where each term is greater than zero. They are widely used to represent growth and positive change, enabling us to comprehend and analyze various phenomena.
A positive term series refers to a sequence of numbers where each term is greater than zero. Such a series exhibits a consistent pattern of positive increments or growth. The terms in a positive term series can represent various phenomena, such as population growth, financial investments, or mathematical progressions.
Typically, a positive term series can be defined using a recursive formula or by specifying the relationship between consecutive terms. For instance, the Fibonacci sequence is a well-known positive term series where each term is the sum of the two preceding terms (e.g., 1, 1, 2, 3, 5, 8, 13, ...).
Positive term series are of great interest in mathematics and real-world applications. They allow us to model and understand processes that exhibit growth or positive change over time. By studying the patterns and properties of these series, we can make predictions, analyze trends, and derive valuable insights.
Learn more about series
https://brainly.com/question/26263191
#SPJ11
conventional, rectangular flocculation basin is 38 ft. wide, 90 ft. long and 16 ft. deep. The flow through the basin is 24 MGD and the water horsepower input by the reel type paddles is 15 hp. The dynamic viscosity of water is 2.73 E -5 lb/sec/ft2 at 50 degrees Fahrenheit.
a. What is the nominal detention time?
b. What velocity gradient is induced by the reel paddles?
c. What is the GT value?
The nominal detention time is the time needed for a small particle of water in the system to flow from the inlet of the system to the outlet. The nominal detention time is 24.6 min. The velocity gradient is 7.5. The GT value is 184.5.
(a) The nominal detention time is the time needed for a small particle of water in the system to flow from the inlet of the system to the outlet. The formula for the nominal detention time is as follows;
Nominal detention time = Volume of basin / Flow rate
The volume of the basin is given by; V = L x W x DV
= 90 ft. x 38 ft. x 16 ft.
= 54,720 cubic feet
Note: 1 cubic foot = 7.48 gallons (US) Therefore, the volume of the basin in gallons is;
V = 54,720 cubic feet x 7.48 gallons/cubic feet = 409,369 gallons
Flow rate = 24 MGD = 24 x 1,000,000 / 1440 = 16,667 gallons/min
Nominal detention time = Volume of basin / Flow rate
Nominal detention time = 409,369 gallons / 16,667 gallons/min
Nominal detention time = 24.6 min
Therefore, the nominal detention time is 24.6 min.
(b) Velocity gradient is given by the formula; Velocity gradient, G = 8U / D
Where; U = water horsepower input by the reel type paddles
D = depth of the tank in ft
Velocity gradient, G = (8 x 15) / 16G
= 7.5
Therefore, the velocity gradient is 7.5.
(c) GT value is given by the formula; GT = G x t
Where; G = Velocity gradient
t = nominal detention time
GT = 7.5 x 24.6GT
= 184.5
Therefore, the GT value is 184.5.
To know more about velocity visit :
https://brainly.com/question/18084516
#SPJ11
Catchment has a total area of 50,000 ha. The annual rainfall of the catchment is 1260 mm)and the average discharge at the outlet of the catchment is 10 m³/s. In a six-month period, the total surface water storage in the catchment is found to decrease by 24 Mm3. During the same period, the average monthly evapotranspiration is estimated to be 25 mm. Determine the average infiltration rate in mm/day. Ignore other losses.
The catchment has a 50,000 ha area, 1260 mm annual rainfall, and 10 m³/s discharge. Over six months, surface water storage decreases by 24 Mm3, and evapotranspiration increases by 25 mm. The average infiltration rate is 3.21 mm/day.
Given information; Catchment has a total area of 50,000 ha. The annual rainfall of the catchment is 1260 mm)and the average discharge at the outlet of the catchment is 10 m³/s. In a six-month period, the total surface water storage in the catchment is found to decrease by 24 Mm3.
During the same period, the average monthly evapotranspiration is estimated to be 25 mm. We have to find the average infiltration rate in mm/day.There are various methods to determine the average infiltration rate in mm/day. The following method will be used to determine the average infiltration rate in mm/day.
Infiltration = Rainfall - Runoff - Evapotranspiration - Change in Storage Infiltration
= (1260 mm/yr)/365 days/yr
Infiltration = 3.45 mm/day
Change in storage = (-24 Mm3 * 1E6 m3/Mm3)/(50,000 ha * 10,000 m2/ha)
Change in storage = -48 mm
Total loss = 25 mm + 48 mm
Total loss = 73 mm
Infiltration = 1260 mm/yr - 10 m³/s * 86,400 s/day/ha * 50,000 ha/yr - 73 mm/yr
Infiltration = 1173 mm/yr = 3.21 mm/day
Therefore, the average infiltration rate in mm/day is 3.21 mm/day.
To know more about Infiltration Visit:
https://brainly.com/question/30639661
#SPJ11
The average infiltration of Catchment which has a total area of 50,000 ha. is approximately 6.16 mm/day.
Given:
Catchment area = 50,000 ha
Rainfall = 1260 mm
Discharge = 10 m³/s
Decrease in storage = 24 Mm³
Evapotranspiration = 25 mm (monthly)
conversion of the catchment area from hectares to square meters:
Catchment area =[tex]{50,000 ha\times 10,000 m^2}{ha}[/tex]
= 500,000,000 m²
Next, we need to calculate the total volume of water that enters the catchment through rainfall in cubic meters:
Total rainfall volume = [tex]Catchment area \times rainfall[/tex]
[tex]= 500,000,000 m^2 \times 1260 mm[/tex]
= 630,000,000,000 m³
Since the average monthly evapotranspiration is given as 25 mm, the total loss due to evapotranspiration over the six-month period is:
Total evapotranspiration loss =[tex]\dfrac{25 mm}{month} \times 6 months[/tex]
= 150 mm
Now, let's convert the decrease in storage from Mm³ to cubic meters:
Decrease in storage =[tex]\dfrac{24 Mm^3 \times 1,000,000 m^3}{Mm^3}[/tex]
= 24,000,000 m³
To find the net volume of water available for infiltration, we subtract the evapotranspiration loss and the decrease in storage from the total rainfall volume:
Net volume for infiltration = Total rainfall volume - Total evapotranspiration loss - Decrease in storage
= [tex]630,000,000,000 m^3\times - 150 mm \times 500,000,000 m^2 - 24,000,000 m^3\\= 629,250,000,000 m^3 - 75,000,000,000 m^3 - 24,000,000 m^3\\= 554,250,000,000 m^3[/tex]
Next, we need to convert the net volume to millimeters:
Net volume for infiltration = [tex]\dfrac{554,250,000,000 m^3} {500,000,000 m^2}[/tex]
= 1108.5 mm
Finally, we divide the net volume by the number of days in the six-month period to find the average infiltration rate in mm/day:
Average infiltration rate =[tex]\dfrac{ Net volume for infiltration }{(\dfrac{6 months \times 30 days}{month})}[/tex]
= [tex]\dfrac{1108.5 mm} {(180 days)}[/tex]
≈ 6.16 mm/day
Therefore, the average infiltration rate in mm/day is approximately 6.16 mm/day.
Learn more about average infiltration here :
https://brainly.com/question/33214992
#SPJ4
Sodium sulfate, Na_2SO_4 , and barium chloride, BaCl_2 , are soluble compounds that form clear solutions. However, when aqueous solutions of sodium sulfate and barium chloride are mixed together, a white solid (a precipitate) forms.
Sodium sulfate and barium chloride are soluble compounds that form clear solutions. However, when aqueous solutions of sodium sulfate and barium chloride are mixed together, a white solid (a precipitate) forms.
This is because sodium sulfate and barium chloride react to form barium sulfate, which is a white, insoluble solid. The chemical reaction is as follows:
Na_2SO_4 (aq) + BaCl_2 (aq) → BaSO_4 (s) + 2NaCl (aq)
The barium sulfate precipitates out of solution because it is less soluble than the sodium sulfate and barium chloride solutions. The sodium chloride solution remains in solution because it is more soluble than the barium sulfate.
The formation of the white precipitate is a classic example of a double displacement reaction. In a double displacement reaction, two ionic compounds exchange ions to form two new compounds. In this case, the sodium ions from the sodium sulfate solution exchange with the barium ions from the barium chloride solution to form barium sulfate. The chloride ions from the sodium chloride solution exchange with the sodium ions from the sodium sulfate solution to form sodium chloride.
The formation of the white precipitate can be used as a qualitative test for barium ions. If a clear solution of barium chloride is added to a solution that contains sulfate ions, a white precipitate will form if sulfate ions are present. This is because the barium sulfate precipitate is insoluble and will form a solid.
You can learn more about sodium sulfate at
https://brainly.com/question/3047839
#SPJ11
1. Calculate the compressive strength of cylinders at the age of testing Compressive Strength (f) Ultimate Load(P) Cross Sectional Area(A) where: fc is in MPa Pis in N A is in mm2 Compare the calculated compressive strength with those obtained from the Schmidt hammer
Compressive strength of the cylinders at the age of testing can be calculated as shown below;
[tex]f = \frac {P}{A}[/tex]
Where: f is the compressive strength in MPa
P is the ultimate load in NA is the cross-sectional area in mm²
Now let us calculate the compressive strength of cylinders at the age of testing.
We can start by filling in the values in the equation above;
[tex]f = \frac{P}{A}\\f = \frac {2390}{7854}\\f = 0.3046 MPa[/tex]
Compare the calculated compressive strength with those obtained from the Schmidt hammer The values obtained from the Schmidt hammer at the age of testing were as follows:
27.8 MPa, 30.1 MPa, and 28.9 MPa.
Therefore, the calculated compressive strength of 0.3046 MPa is significantly lower than the values obtained from the Schmidt hammer. This could be as a result of several factors such as poor workmanship or inaccurate testing procedures.
The most accurate method of testing compressive strength is through destructive testing. This involves testing the cylinders in a controlled environment and breaking them to determine the maximum compressive strength that they can handle.
However, this is not always practical as it is time-consuming and expensive.
To know more about cylinders, visit:
https://brainly.com/question/12248187
#SPJ11
If a particle is moving, it has kinetic energy. Kinetic energy is the energy of motion, and it depends on the speed and mass of the particle. It is given by the formula E_k=1/2 mv^2. where E_k
is the kinetic energy, m is the mass, and v is the speed of the particle. The formula for kinetic energy has some important features to keep in mind. to the vector quantity momentum, which you might have already studied.) squaring it would always lead to a positive result.) This means that doubling a particle's speed will quadruple its kinetic energy. energy. A student with a mass of 63.0 kg is walking at a leisurely pace of 2.30 m/s. What is the student's kinetic energy (in J)? at this speed?
The student's kinetic energy at a speed of 2.30 m/s is 167.82 Joules (J).
The kinetic energy of a particle is given by the formula E_k = 1/2 mv², where
E_k is the kinetic energy,
m is the mass, and
v is the speed of the particle.
To find the student's kinetic energy, we need to substitute the given values into the formula. The mass of the student is given as 63.0 kg, and the speed is given as 2.30 m/s.
1. Substitute the values into the formula:
E_k = 1/2 * 63.0 kg * (2.30 m/s)²
2. Calculate the square of the speed:
(2.30 m/s)^2 = 5.29 m²/s²
3. Multiply the mass and the square of the speed:
1/2 * 63.0 kg * 5.29 m²/s² = 167.82 kg m²/s²
4. Simplify the units to Joules (J):
167.82 kg m²/s² = 167.82 J
Learn more about kinetic energy :
https://brainly.com/question/1135367
#SPJ11
Describe the expected relationship given the following pairs of variables. You explanation should discuss how the fwo variables could be compared to each other. 3] a) A player's distance from a dartboard and their score. b) The height of a student and the number of minutes of TV they spend watching each nigh
A player's distance from a dartboard and their score: It can be observed that there is an inverse relationship between a player's distance from a dartboard and their score. As a player moves closer to the dartboard, their score would increase.
Similarly, as a player moves further away from the dartboard, their score would decrease. Therefore, it can be said that the closer a player is to the dartboard, the higher their score will be.b) The height of a student and the number of minutes of TV they spend watching each night:It cannot be said that there is a clear expected relationship between the height of a student and the number of minutes of TV they spend watching each night.
The two variables cannot be compared to each other because they are not related to each other. They do not have any direct or indirect relationship between them. Therefore, it is not possible to predict how a student's height would affect the number of minutes of TV they watch each night.
To know more about dartboard visit:
https://brainly.com/question/30368759
#SPJ11
A 20.0-mL sample of 0.25M HCl is reacted with 0.15M NaOH. What is the pH of the solution after 50.0 mL of NaOH have been added to the acid? Show all work
The pH of the solution is 12.55.
The chemical equation for the reaction between HCl (acid) and NaOH (base) is:
HCl (aq) + NaOH (aq) → NaCl (aq) + H2O (l)
Step-by-step explanation:
First, let's calculate the number of moles of HCl in the 20.0-mL sample using the given molarity:
Molarity = moles of solute / liters of solution
0.25 M = moles of HCl / 0.0200 L
moles of HCl = 0.25 M x 0.0200 L = 0.00500 mol
Next, we calculate the number of moles of NaOH in the 50.0-mL sample using the given molarity:
Molarity = moles of solute / liters of solution
0.15 M = moles of NaOH / 0.0500 L
moles of NaOH = 0.15 M x 0.0500 L = 0.00750 mol
Since HCl and NaOH react in a 1:1 molar ratio, we know that 0.00500 mol of NaOH will react with all of the HCl.
That leaves 0.00750 - 0.00500 = 0.00250 mol of NaOH remaining in solution.
The total volume of the solution is 20.0 mL + 50.0 mL = 70.0 mL = 0.0700 L.
So, the concentration of NaOH after the reaction is complete is:
Molarity = moles of solute / liters of solution
Molarity = 0.00250 mol / 0.0700 L
Molarity = 0.0357 M
To find the pH of the solution, we first need to find the pOH:
pOH = -log[OH-]
We can find [OH-] using the concentration of NaOH:
pOH = -log(0.0357)
pOH = 1.45
pH + pOH = 14
pH + 1.45 = 14
pH = 12.55
Learn more about pH from the given link:
https://brainly.com/question/12609985
#SPJ11
AutoCAD questions
12. Extension for a template file: A. .dwg C. plt B. shut D. sth 13. When typing text, typing in % %D will give you the symbol. A. Diameter B. Plus C. Minus D. Degree 14. An extension line begins the
The extension for a template file in AutoCAD is .dwg.
When typing text, typing in %%D will give you the symbol for Diameter.
A template file in AutoCAD is a preformatted drawing file that contains the settings, layers, styles, and other elements needed for creating new drawings. The extension for these template files is .dwg, which stands for drawing. By using a template file, users can start new drawings with the predefined settings and layout, saving time and ensuring consistency in their work.
When typing text in AutoCAD, you can use special characters and symbols by using escape codes. Typing in %%D will give you the symbol for Diameter. This is useful when annotating drawings or adding dimensions that require the diameter symbol to represent circular features.
.dwg extension and template files in AutoCAD to understand how they can streamline your workflow and enhance productivity. Using escape codes to access special symbols like the diameter symbol can help improve the clarity and accuracy of your annotations and dimensions.
Learn more about extension
brainly.com/question/32421418
#SPJ11
1 im (√√+1+√√√+2+ + √√n+n). ... 818 Evaluate lim
To evaluate the limit of the given expression, lim (n → ∞) ∑√√k+k, where the summation runs from k = 1 to n, we can rewrite the expression as a Riemann sum and then take the limit as the number of terms approaches infinity. By applying the limit properties, we find that the limit of the given expression is ∞.
The given expression can be rewritten as a Riemann sum of the function f(k) = √√k+k, where the summation runs from k = 1 to n. The Riemann sum approximates the area under the curve of the function f(k) over the interval [1, n] using subintervals.
As n approaches infinity, the number of subintervals increases indefinitely, and each subinterval's width approaches zero. Consequently, the Riemann sum approaches the integral of f(k) over the interval [1, ∞).
To evaluate the limit, we need to examine the behavior of the function f(k) as k approaches infinity. Since the function f(k) contains nested square roots, it grows without bound as k increases. As a result, the integral of f(k) over the interval [1, ∞) diverges to infinity.
Therefore, the limit of the given expression, lim (n → ∞) ∑√√k+k, is ∞, indicating that the sum diverges to infinity as the number of terms increases.
Learn more about limit here : brainly.com/question/12383180
#SPJ11
How will you prioritise water allocation of a dam, when the
demand is for
I. Irrigation
II. Domestic
III. Eskom and Industries
IV. International obligation
V. Environmental flow
VI. Explain Reserve
When prioritizing water allocation for a dam, several factors need to be considered to ensure efficient and fair distribution. Here is a step-by-step approach to prioritize water allocation for different demands:
1. Start with the highest priority demand, which is often irrigation. Irrigation is crucial for agriculture and food production. Allocate a sufficient amount of water for irrigation to support crop growth and maintain agricultural productivity.
2. Move on to domestic water supply. People need water for drinking, cooking, and daily household activities. Allocate an appropriate amount of water for domestic use, considering the population served by the dam and their basic needs.
3. Next, consider Eskom and industries. Eskom refers to the energy provider, and industries encompass various sectors like manufacturing and mining. These sectors play a significant role in economic development and job creation. Allocate a portion of water to ensure the smooth functioning of Eskom and industries, but without compromising other demands.
4. International obligations may arise if the dam is part of a transboundary water agreement. If there are treaties or agreements in place, allocate the required water to fulfill international commitments.
5. Environmental flow is crucial for maintaining the health of ecosystems and biodiversity. Allocate a portion of water to ensure the minimum required flow downstream, allowing for the survival of aquatic life, water quality maintenance, and ecosystem sustainability.
6. Lastly, the "Explain Reserve" refers to a reserved amount of water that is kept for emergency situations or unforeseen circumstances. This reserve ensures there is a buffer available to address any sudden water shortage or unexpected events.
It is important to note that the specific allocation percentages or volumes for each demand will depend on various factors, such as local regulations, water availability, and the dam's capacity. Prioritizing water allocation in a dam requires balancing different needs to ensure sustainable and equitable distribution.
Learn more about biodiversity from the link:
https://brainly.com/question/26110061
#SPJ11
A packed countercurrent water-cooling tower is to cool water from 55 °C to 35 °C using entering air at 35 °C with wet bulb temperature of 27 °C. The water flow is 160 kg water/s. The diameter of the packed tower is 12 m. The heat capacity CL is 4.187 x 103 J/kg•K. The gas- phase volumetric mass-transfer coefficient koa is estimated as 1.207 x 107 kg mol/som.Pa and liquid-phase volumetric heat transfer coefficient ha is 1.485 x 104 W/m3.K. The tower operates at atmospheric pressure. The enthalpies of saturated air and water vapor mixtures for equilibrium line is exhibited in the Table E1. (a) Calculate the minimum air flow rate. (10 points) (b) Calculate the tower height needed if the air flow is 1.5 times minimum air flow rate using graphical or numerical integration.
a) The minimum air flow rate can be calculated by determining the heat transfer required to cool the water from 55 °C to 35 °C and dividing it by the difference in enthalpy between the incoming and outgoing air streams.
b) To calculate the tower height needed for an air flow rate of 1.5 times the minimum, integration can be used to determine the mass transfer and heat transfer as a function of height in the tower. By integrating these values, the tower height required can be obtained.
Explanation:
a) The minimum air flow rate can be calculated by first determining the heat transfer required to cool the water. This is done by multiplying the water flow rate (160 kg/s) by the specific heat capacity of water (4.187 x 10^3 J/kg•K) and the temperature difference (55 °C - 35 °C). The resulting heat transfer rate is then divided by the difference in enthalpy between the incoming and outgoing air streams, which can be obtained from the enthalpy table.
b) To calculate the tower height needed for an air flow rate of 1.5 times the minimum, the mass transfer and heat transfer as a function of height in the tower need to be determined. This can be done using graphical or numerical integration techniques. By integrating these values and considering the increased air flow rate, the tower height required can be obtained.
To know more about enthalpies of saturated air and water visit:
https://brainly.com/question/10881958
#SPJ11
Find the arc length of the curve x=3sinθ−sin3θ ,y=3cosθ−cos3θ,
0≤θ≤π/2
The arc length of the curve is (3/2)sqrt[2] + (3/4)πsqrt[2], or approximately 6.368 units.
To find the arc length of the curve, we can use the formula:
L = ∫(a to b) sqrt[dx/dθ)^2 + (dy/dθ)^2] dθ
where a and b are the limits of integration.
First, we need to find dx/dθ and dy/dθ.
dx/dθ = 3cosθ - 3cos(3θ)
dy/dθ = -3sinθ + 3sin(3θ)
Next, we substitute these into the formula for arc length and evaluate the integral:
L = ∫(0 to π/2) sqrt[(3cosθ - 3cos(3θ))^2 + (-3sinθ + 3sin(3θ))^2] dθ
= ∫(0 to π/2) sqrt[9cos^2θ - 18cosθcos(3θ) + 9cos^2(3θ) + 9sin^2θ - 18sinθsin(3θ) + 9sin^2(3θ)] dθ
= ∫(0 to π/2) sqrt[18 - 18(cos^2θcos(3θ) + sin^2θsin(3θ))] dθ
= ∫(0 to π/2) sqrt[18 - 18sin(θ)cos(θ)(cos^2(2θ) + sin^2(2θ))] dθ
= ∫(0 to π/2) sqrt[18 - 18sin(θ)cos(θ)] dθ
= ∫(0 to π/2) 3sqrt[2]sqrt[2 - 2sin(2θ)] dθ (using the trig identity sin(θ)cos(θ) = (1/2)sin(2θ))
We can then use the substitution u = 2θ, du = 2dθ to simplify the integral:
L = (3sqrt[2]/2) ∫(0 to π) sqrt[2 - 2sin(u)] du
= (3sqrt[2]/2) ∫(0 to π/2) sqrt[2 - 2sin(u)] du + (3sqrt[2]/2) ∫(π/2 to π) sqrt[2 - 2sin(u)] du (since sqrt[2 - 2sin(u)] is an even function)
Using the substitution v = cos(u), dv = -sin(u)du, we can simplify further:
L = (3sqrt[2]/2) ∫(0 to 1) sqrt[2 - 2v^2] dv + (3sqrt[2]/2) ∫(0 to 1) sqrt[2 - 2v^2] dv
= 3sqrt[2] ∫(0 to 1) sqrt[2 - 2v^2] dv
We can now use the trig substitution v = sin(t) to complete the integral:
L = 3sqrt[2] ∫(0 to π/2) sqrt[2 - 2sin^2(t)] cos(t) dt (since dv = cos(t)dt)
= 3sqrt[2] ∫(0 to π/2) sqrt[2cos^2(t)] cos(t) dt (using the identity sin^2(t) + cos^2(t) = 1)
= 3sqrt[2] ∫(0 to π/2) 2cos^2(t) dt
= 3sqrt[2] [sin(t)cos(t) + (1/2)t] |_0^(π/2)
= 3sqrt[2] [(1/2)(1) + (1/4)π]
= (3/2)sqrt[2] + (3/4)πsqrt[2]
Therefore, the arc length of the curve is (3/2)sqrt[2] + (3/4)πsqrt[2], or approximately 6.368 units.
Learn more about length from
https://brainly.com/question/2217700
#SPJ11
Calculate the change in vapor pressure of 1 kg boiling water T = 373.15 K if you add 1 mole of NaCl!
Solution = p = 0,96525⋅10^5 Pa
Please show me how to get to the solution!
The change in vapor pressure of 1 kg boiling water (T = 373.15 K) if you add 1 mole of NaCl is -49181.4 Pa.
Given:
T = 373.15 K
P1° = 101325 Pa (atm) = 1
P2 = 0.96525 × [tex]10^5[/tex] Pa (atm) = 0.95
Kf = 0.512
Using Raoult's Law:
Δp = -X2 × P1° × Kf
Where:
Δp is the change in vapor pressure
X2 is the mole fraction of the solute
P1° is the vapor pressure of the solvent when pure
Kf is the freezing point depression constant
To find X2, we rearrange the equation:
X2 = P2 / P1° = 0.95 / 1 = 0.95
Substituting the values:
Δp = -X2 × P1° × Kf
Δp = -0.95 × 101325 × 0.512
Δp = -49181.4 Pa (or N/[tex]m^2[/tex])
Learn more about vapor pressure from the given link:
https://brainly.com/question/2693029
#SPJ11
The set B={1+t^2,−2t−t^2,1+t+t^2} is a basis for P2. Find the coordinate vector of p(t)=−5−7t−8t^2 relative to B. (Simplify your answers.)
The coordinate vector of p(t) = -5 - 7t - 8t^2 relative to the basis B = {1 + t^2, -2t - t^2, 1 + t + t^2} is [3, -7, -6].
To find the coordinate vector of p(t) relative to the basis B, we need to express p(t) as a linear combination of the basis vectors and find the coefficients.
We start by writing p(t) as a linear combination of the basis vectors:
p(t) = c1(1 + t^2) + c2(-2t - t^2) + c3(1 + t + t^2)
Expanding and collecting like terms, we have:
p(t) = (c1 - c2 + c3) + (c1 - 2c2 + c3)t + (c1 - c2 + c3)t^2
Comparing the coefficients of the polynomial terms on both sides, we get the following system of equations:
c1 - c2 + c3 = -5
c1 - 2c2 + c3 = -7
c1 - c2 + c3 = -8
Simplifying the system, we can see that the third equation is redundant as it is the same as the first equation. Thus, we have:
c1 - c2 + c3 = -5
c1 - 2c2 + c3 = -7
Solving this system of equations, we find that c1 = 3, c2 = -7, and c3 = -6.
Therefore, the coordinate vector of p(t) relative to the basis B is [3, -7, -6].
Learn more about Coordinate vector
brainly.com/question/32768567
#SPJ11
Calculate the oxygen balance of an ANFO having 96% AN and 4% FO.
please show full workings
ANFO having 96% AN and 4% FO has an oxygen balance of 2.08%.
ANFO is a mixture of ammonium nitrate and fuel oil in the ratio of 96:4.
To calculate the oxygen balance of ANFO, follow the steps given below:
Calculate the molecular weight of AN and FO
Ammonium Nitrate (AN)
Molecular weight of nitrogen = 14 g/mol
Molecular weight of oxygen = 16 g/mol
Molecular weight of nitrogen in AN = 28 g/mol
Molecular weight of oxygen in AN = 48 g/mol
Molecular weight of AN = 28 + 48 = 76 g/mol
Fuel Oil (FO)
Molecular weight of carbon = 12 g/mol
Molecular weight of hydrogen = 1 g/mol
Molecular weight of FO = 12(14) + 1(24) = 168 g/mol
Calculate the weight of oxygen in AN and FO
ANFO has 96% AN and 4% FO
By weight, AN = 96% of 100g = 96 g
FO = 4% of 100g = 4 g
Oxygen in AN
Weight of oxygen in AN = 48 g/mol × 0.96 g/g mol = 46.08 g
Oxygen in FO
Weight of carbon in FO = 12 × 0.04 g/g mol = 0.48 g
Weight of hydrogen in FO = 1 × 0.04 g/g mol = 0.04 g
Weight of oxygen in FO = (0.48 + 0.04) × (16/18) g/g mol = 0.48 g
Oxygen Balance
Oxygen balance = weight of oxygen released/theoretical amount of oxygen released× 100%
Theoretical amount of oxygen released = weight of AN × (3/2) = 96 g × (3/2) = 144 g
Weight of oxygen released = weight of fuel × 0.75 = 4 g × 0.75 = 3 g
Oxygen balance = 3/144 × 100% = 2.08%
Therefore, ANFO having 96% AN and 4% FO has an oxygen balance of 2.08%.
To know more about oxygen balance, click here
https://brainly.com/question/16320338
#SPJ11
A vending machine is designed to dispense a mean of 7.7 oz of coffee into an 8−0z cup. If the standard deviation of the amount of coffee dispensed is 0.50oz and the amount is normally distributed, determine the percent of times the machine will dispense more than 7.1oz ________%o of the time the machine will dispense more than 7.1 oz:
To find the percentage of times the vending machine dispenses more than 7.1 oz of coffee, we can use the standard normal distribution since the amount dispensed is normally distributed.
We can start by finding the z-score associated with 7.1 oz of coffee's = (x - μ) / σwhere
x = 7.1 oz,
μ = 7.7 oz, and
σ = 0.5
ozz
= (7.1 - 7.7) / 0.5
= -1.2
Now, we need to find the percentage of times the machine will dispense more than 7.1
The cumulative distribution function gives the area to the left of a given z-score, so we need to subtract this area from 1 to get the area to the right.
P(z > -1.2)
= 1 - P(z ≤ -1.2)
= 1 - 0.11507
= 0.88493
The percentage of times the machine will dispense more than 7.1 oz is 88.493%, or approximately 88.5%.
Answer: 88.5%.
To know more about dispenses visit:
https://brainly.com/question/30206530
#SPJ11