The maximum energy stored in the inductor at any time is 18J.
(a) The formula for the angular frequency of oscillation (W) for an electromagnetic oscillator (LC circuit) is given by:
[tex]W = 1 / sqrt(LC)[/tex]
Given L = 1 and C = 4F,
we have:
W = 1 / sqrt(1 x 4)
W = 1 / 2rad/s
(b) The formula for the charge on a capacitor in an electromagnetic oscillator (LC circuit) at any time t is given by:
q(t) = Q0 cos(Wt)
and the formula for the voltage across the capacitor in an electromagnetic oscillator (LC circuit) at any time t is given by:
[tex]v(t) = V0 sin(Wt)[/tex]
At the point when the capacitor is fully discharged for the second time, the voltage across the capacitor will be zero (V0 sin(Wt) = 0).
Thus, sin(Wt) = 0, and Wt = nπ.
Since we are interested in the second time the capacitor is fully discharged, n = 2.
Therefore, Wt = 2π, and t = 2π / W
= 2π x 2 = 4s.
(c) The formula for the energy stored in an inductor in an electromagnetic oscillator (LC circuit) at any time t is given by: [tex]U(t) = (1/2)Li²(t)[/tex]
Since the capacitor is fully charged to 3V, we can calculate the initial charge on the capacitor as:
Q0 = CV0
= 4 x 3
= 12CAt
t = 0, the charge on the capacitor is Q0 cos(0) = Q0 = 12C, and the current in the inductor is zero.
Thus, the energy stored in the inductor at t = 0 is zero.
Since energy is conserved in an electromagnetic oscillator (LC circuit), the total energy stored in the circuit must remain constant.
Thus, the maximum energy stored in the inductor at any time is equal to the initial energy stored in the capacitor, which is given by:
(1/2)CV0²
= (1/2)(4)(3²)
= 18J
Therefore, the maximum energy stored in the inductor at any time is 18J.
To learn more about inductor visit;
https://brainly.com/question/31503384
#SPJ11
In a photoelectric effect experiment, it is observed that green light does eject electrons from a particular metal. Next, when a shorter wavelength of light is used with the same intensity, which result is possible? b Select one or more: Оа. electrons are ejected at a greater rate and with a larger maximum kinetic energy electrons are ejected at a greater rate but with a smaller maximum kinetic energy electrons are ejected at a lower rate and with a smaller maximum kinetic energy O d. electrons are ejected at a lower rate but with a larger maximum kinetic energy O e there are no ejected electrons
Electrons are ejected at a greater rate and with a larger maximum kinetic energy result is possible. Option A is correct.
In the photoelectric effect, when light of a sufficiently high frequency (shorter wavelength) shines on a metal surface, electrons can be ejected from the metal. The intensity of light refers to the brightness or the number of photons per unit area per unit time.
Based on the photoelectric effect, we can deduce the following possibilities when a shorter wavelength of light is used with the same intensity:
a) Electrons are ejected at a greater rate and with a larger maximum kinetic energy.
This possibility is consistent with the photoelectric effect. When shorter wavelength light is used, the energy of individual photons increases, and each photon can transfer more energy to the electrons, resulting in higher kinetic energy for the ejected electrons. Additionally, the greater number of photons (higher rate) can lead to more electrons being ejected.
Therefore, the correct answer is A.
Learn more about Electrons -
brainly.com/question/860094
#SPJ11
One mole of an ideal gas is held at a constant pressure of 1 atm. Find the change in volume (in liters) if the temperature changes by 62°C.
The change in volume of one mole of an ideal gas held at a constant pressure of 1 atm if the temperature changes by 62°C is 2.4 liters.
The ideal gas law states that PV = nRT, where P is the pressure, V is the volume, n is the number of moles of gas, R is the ideal gas constant, and T is the temperature in Kelvin.
If we rearrange the equation to solve for V, we get V = nRT/P.
In this problem,
we are given that P = 1 atm, n = 1 mole,
and T changes from 273 K (0°C) to 335 K (62°C).
Plugging these values into the equation,
we get V = (1 mol)(8.314 J/mol K)(335 K)/1 atm = 2.4 liters.
Therefore, the change in volume is 2.4 liters. This means that the volume of the gas will increase by 2.4 liters if the temperature is increased by 62°C.
To learn more about ideal gas here brainly.com/question/26088764
#SPJ11
The p-T dilagrats beícw is an: A. isobasic compression: B. isctherrmail evpansion; C. iscobaric exparisiont D. iscocharic carripressiart, Hirit 1. Which state variabile, p,W or T is constane an a prociess represented by a line paralleil with the T awis? Hirit 2:pV=nRT
1. The p-T dilagrats beícw is an: B. isctherrmail evpansion. the process represented by a line parallel to the T axis is an isothermal expansion, where the temperature remains constant.
2. In an isothermal expansion, the system undergoes a process where the temperature (T) remains constant. This means that as the volume (V) increases, the pressure (p) decreases to maintain equilibrium. The equation pV = nRT represents the ideal gas law, where p is the pressure, V is the volume, n is the number of moles of gas, R is the gas constant, and T is the temperature. In this case, since the process is isothermal, T is held constant.
3. The isothermal expansion occurs when a gas expands while being in contact with a heat reservoir that maintains a constant temperature. As the volume increases, the gas particles spread out, leading to a decrease in pressure. The energy transferred to or from the system is solely in the form of heat to maintain the constant temperature. This process is often observed in various industrial applications and the behavior of ideal gases under controlled conditions.
The p-T dilagrats beícw is an isothermal expansion. In this process, the temperature remains constant, while the pressure and volume change. It is represented by a line parallel to the T axis in a p-T diagram.
To know more about Isothermal expansion , visit:- brainly.com/question/30329152
#SPJ11
A 13.7-H inductor carries a current of 19 A. How much ice at 0°C could be melted by the energy stored in the magnetic field of the inductor? (Hint: Use the value L 334 J/g for ice.)
The energy stored in the magnetic field of the inductor is approximately 3484.515 Joules. The energy stored in the magnetic field of the inductor could melt approximately 10.42 grams of ice at 0°C. The energy stored in an inductor (U) can be calculated using the formula:
U = (1/2) * L *[tex]I^2[/tex]
where L is the inductance in henries (H) and I is the current in amperes (A).
Inductance (L) = 13.7 H
Current (I) = 19 A
Substituting these values into the formula:
U = (1/2) * 13.7 H * ([tex]19 A)^2[/tex]
U = (1/2) * 13.7 H * [tex]361 A^2[/tex]
U ≈ 3484.515 J
The energy stored in the magnetic field of the inductor is approximately 3484.515 Joules.
Now, to find the amount of ice that could be melted by this energy, we can use the specific heat of ice (334 J/g). The specific heat represents the energy required to raise the temperature of 1 gram of substance by 1 degree Celsius. Let's assume all the energy is transferred to the ice and none is lost to the surroundings. The amount of ice melted (m) can be calculated using the formula:
m = U / (specific heat of ice)
m = 3484.515 J / 334 J/g
m ≈ 10.42 g
Therefore, the energy stored in the magnetic field of the inductor could melt approximately 10.42 grams of ice at 0°C.
Learn more about magnetic field here:
https://brainly.com/question/19542022
#SPJ11
A 5nC charge is located at (0,7)cm and another 2nC charge is located at (−3,0)cm. What would be the magnitude of the net electric field at the origin (0,0)cm ?
The magnitude of the net electric field at the origin (0,0) cm is approximately [tex]83.19 × 10^6 N/C[/tex].
To calculate the magnitude of the net electric field at the origin, we need to calculate the electric fields generated by each charge and then sum them up.
The electric field at a point due to a point charge is given by Coulomb's Law:
E = k * (q / [tex]r^2[/tex])
where E is the electric field, k is the electrostatic constant ([tex]9 × 10^9 Nm^2/C^2[/tex]), q is the charge, and r is the distance from the charge to the point.
Let's calculate the electric fields generated by each charge at the origin:
For the 5nC charge:
q1 = 5nC
r1 = 7 cm = 0.07 m
E1 = k * (q1 / [tex]r1^2[/tex])
For the 2nC charge:
q2 = 2nC
r2 = 3 cm = 0.03 m
E2 = k * (q2 / [tex]r2^2[/tex])
Now, we can calculate the net electric field by summing up the electric fields:
E_net = E1 + E2
Substituting the values and performing the calculations:
[tex]E1 = (9 × 10^9 Nm^2/C^2) * (5 × 10^(-9) C) / (0.07 m)^2[/tex]
E1 ≈ 9188571.43 N/C
[tex]E2 = (9 × 10^9 Nm^2/C^2) * (2 × 10^(-9) C) / (0.03 m)^2[/tex]
E2 ≈ 74000000 N/C
E_net = E1 + E2
E_net ≈ 83188571.43 N/C
To know more about electric field refer to-
https://brainly.com/question/11482745
#SPJ11
P1 = P0 + rho g h1
Where
P0 = weight of air at sea level = 1.01 X 105
Pa
rho = m/V Density
= mass/volume
F1/A1=F2/A2
The force on a surface area of 2 m^2 is 200 N.
The equation P1 = P0 + rho g h1 is used to calculate the pressure at a height h1 above sea level, where P0 is the pressure at sea level, rho is the density of air, g is the acceleration due to gravity, and h1 is the height above sea level.
The equation F1/A1=F2/A2 is used to calculate the force on a surface area A1 due to a force F1, where F2 is the force on a surface area A2.
Here is an example of how to use these equations:
Suppose we want to calculate the pressure at a height of 1000 meters above sea level. We know that the pressure at sea level is 1.01 x 10^5 Pa, the density of air is 1.225 kg/m^3, and the acceleration due to gravity is 9.81 m/s^2. We can use the equation P1 = P0 + rho g h1 to calculate the pressure at a height of 1000 meters:
P1 = 1.01 x 10^5 Pa + 1.225 kg/m^3 * 9.81 m/s^2 * 1000 m = 113017.25 Pa
Therefore, the pressure at a height of 1000 meters above sea level is 113017.25 Pa.
Here is another example of how to use these equations:
Suppose we have a surface area of 1 m^2 and a force of 100 N acting on it. We can use the equation F1/A1=F2/A2 to calculate the force on a surface area of 2 m^2:
F2 = F1 * A2/A1 = 100 N * 2 m^2 / 1 m^2 = 200 N
Therefore, the force on a surface area of 2 m^2 is 200 N.
Learn more about surface area with the given link,
https://brainly.com/question/16519513
#SPJ11
A 380 kg piano is pushed at constant speed a distance of 3.9 m up a 27° incline by a mover who is pushing parallel to the incline. The coefficient of friction between the piano & ramp is 0.45. (a) De
The force exerted by the mover must balance the forces of gravity and friction.
The work done by the mover would be the force exerted by the mover multiplied by the distance the piano is pushed up the incline.
The piano is being pushed at a constant speed and there is no change in vertical position, the work done by the force of gravity is zero.
(a) To determine the force exerted by the mover, we need to consider the forces acting on the piano. These forces include the force of gravity, the normal force, the force exerted by the mover, and the frictional force. By analyzing the forces, we can find the force exerted by the mover parallel to the incline.
The force exerted by the mover must balance the forces of gravity and friction, as well as provide the necessary force to push the piano up the incline at a constant speed.
(b) The work done by the mover is calculated using the formula
W = F * d, where
W is the work done,
F is the force exerted by the mover
d is the distance moved.
In this case, the work done by the mover would be the force exerted by the mover multiplied by the distance the piano is pushed up the incline.
(c) The work done by the force of gravity can be calculated as the product of the force of gravity and the distance moved vertically. Since the piano is being pushed at a constant speed and there is no change in vertical position, the work done by the force of gravity is zero.
By considering the forces, work formulas, and the given values, we can determine the force exerted by the mover, the work done by the mover, and the work done by the force of gravity in pushing the piano up the incline.
Complete Question-
A 380 kg piano is pushed at constant speed a distance of 3.9 m up a 27° incline by a mover who is pushing parallel to the incline. The coefficient of friction between the piano & ramp is 0.45. (a) Determine the force exerted by the man (include an FBD for the piano): (b) Determine the work done by the man: (c) Determine the work done by the force of gravity
To know more about gravity , click here-
brainly.com/question/31321801
#SPJ11
A house with its own well has a pump in the basement with an output pipe of inner radius 8.74 mm. The pump can maintain a gauge pressure of 4.10 × 10^5 Pa in the output pipe. A showerhead on the second floor (6.70 m above the pump’s output pipe) has 36 holes, each of radius 0.861 mm. The shower is on "full blast" and no other faucet in the house is open. Density of water is 1.00 × 10^3 kg/m3. Ignoring viscosity, with what speed does water leave the showerhead?
The speed of water leaving the showerhead is 11.9 m/s.
To solve this problem, we can use the following equations:
P = ρgh
Where:
P is the pressure in Pa
ρ is the density of water in kg/m^3
g is the acceleration due to gravity (9.8 m/s^2)
h is the height in m
v = √(2gh)
Where:
v is the velocity in m/s
g is the acceleration due to gravity (9.8 m/s^2)
h is the height in m
The pressure at the pump is equal to the gauge pressure plus atmospheric pressure. The atmospheric pressure at sea level is 1.013 × 10^5 Pa.
P₁ pump = 4.10 × 10^5 Pa + 1.013 × 10^5 Pa
= 5.11 × 10^5 Pa
The pressure at the showerhead is equal to the atmospheric pressure.
P₂ showerhead = 1.013 × 10^5 Pa
The pressure difference is then equal to the pump pressure minus the showerhead pressure.
ΔP = P₁ pump - P₂ showerhead
= 5.11 × 10^5 Pa - 1.013 × 10^5 Pa
= 4.097 × 10^5 Pa
Now that we know the pressure difference, we can calculate the velocity of the water leaving the showerhead.
v = √(2 * 9.8 m/s^2 * 6.70 m)
= 11.9 m/s
Therefore, the speed of water leaving the showerhead is 11.9 m/s.
To learn more about atmospheric pressure click here; brainly.com/question/30780169
#SPJ11
A
car is traveling at 20 m/s. When the driver steps harder on the gas
pedal it causes the car to accelerate at 2 m/s^2. How far, in
meters, has the car travled in 3 seconds?
The car would have travelled 69 meters in 3 seconds.
When a car is travelling at 20 m/s and the driver steps harder on the gas pedal, causing the car to accelerate at 2 m/s², the distance the car would have travelled in 3 seconds is given by:
S = ut + 1/2 at²
Where u = initial velocity
= 20 m/s
a = acceleration
= 2 m/s²
t = time taken
= 3 seconds
Substituting these values, we get:
S = 20(3) + 1/2(2)(3)²
S = 60 + 9
S = 69 meters
Therefore, the car would have travelled 69 meters in 3 seconds.
Learn more about meters from the given link
https://brainly.com/question/1578784
#SPJ11
Radios use resonance in order to tune-in to a particular station. A physics student builds a simple radio using a RLC series circuit. They decide to use a resistor with R=49.5Ω, but they only have one capacitor with capacitance C=180pF. To listen to their favorite station KXY 84.8 FM, which is at a frequency of 84.8MHz, what must be the inductance L of their circuit's inductor? L
The inductance (L) of the circuit's inductor must be approximately 120 μH.
In order to tune in to a specific radio station, resonance is utilized in radios. Resonance occurs when the frequency of the radio station matches the natural frequency of the radio circuit. To achieve resonance in a series RLC circuit, the inductive reactance (XL) and the capacitive reactance (XC) should be equal, canceling each other out. The inductive reactance is given by XL = 2πfL, where f is the frequency and L is the inductance of the inductor.
To listen to station KXY 84.8 FM with a frequency of 84.8 MHz (84.8 × 10^6 Hz), we need to determine the inductance (L). First, we need to calculate the capacitive reactance (XC). XC is given by XC = 1 / (2πfC), where C is the capacitance of the capacitor.
Plugging in the values, we have XC = 1 / (2π × 84.8 × 10^6 Hz × 180 × 10^(-12) F). By simplifying this expression, we can find the value of XC.
Once we have the value of XC, we can set it equal to XL and solve for L. Since XC = XL, we can write 1 / (2πfC) = 2πfL. Rearranging this equation and substituting the given values, we can solve for L.
Following these calculations, we find that the inductance (L) of the circuit's inductor must be approximately 120 μH to tune in to station KXY 84.8 FM.
Learn more about circuit's
brainly.com/question/12608491
#SPJ11
Determine the number of moles of oxygen gas in the following
container.
The container holds 2.90 m3 at 17.84oF and
an a gauge pressure of 16.63kPa.
The number of moles of oxygen gas in the container is determined by the ideal gas law, using the given volume, temperature, and pressure 0.993 moles.
To determine the number of moles of oxygen gas in the container, we can use the ideal gas law, which states that PV = nRT, where P is the pressure, V is the volume, n is the number of moles, R is the ideal gas constant, and T is the temperature in Kelvin.
First, let's convert the given temperature from Fahrenheit to Kelvin:
T(K) = (T(°F) + 459.67) × (5/9)
T(K) = (17.84 + 459.67) × (5/9)
T(K) ≈ 259.46 K
Next, we convert the given pressure from kilopascals (kPa) to pascals (Pa):
P(Pa) = P(kPa) × 1000
P(Pa) = 16.63 kPa × 1000
P(Pa) = 16630 Pa
Now, we can rearrange the ideal gas law equation to solve for n (number of moles):
n = PV / RT
Substituting the known values:
n = (16630 Pa) × (2.90 m³) / ((8.314 J/(mol·K)) × (259.46 K))
Simplifying the equation:
n ≈ 0.993 moles
Therefore, the number of moles of oxygen gas in the container is approximately 0.993 moles.
To learn more about moles click here:
brainly.com/question/15209553
#SPJ11
How far apart (m) will two charges, each of magnitude 14 μC, be
a force of 0.80 N on each other? Give your answer to two decimal
places.
Two charges of magnitude 14 μC will be 4.00 m apart if the force of attraction between them is 0.80 N. This is the required answer. TCoulomb's Law describes the electrostatic interaction between charged particles.
This law states that the force of attraction or repulsion between two charged particles is directly proportional to the product of the charges and inversely proportional to the square of the distance between them. The formula for Coulomb's law is:F = kQ1Q2/d²where F is the force between two charges, Q1 and Q2 are the magnitudes of the charges, d is the distance between the two charges, and k is the Coulomb's constant.
Electric charges are the fundamental properties of matter. There are two types of electric charges: positive and negative. Like charges repel each other, and opposite charges attract each other. Electric charges can be transferred from one object to another, which is the basis of many electrical phenomena such as lightning and electric circuits. The unit of electric charge is the coulomb (C).
To know more about repel visit:
https://brainly.com/question/15744700
#SPJ11
In a particular fission of a uranium-235 (235 U) nucleus, which has neutral atomic mass 235.0439 u, a reaction energy of 200 MeV is released. (a) A mass of 1.00 kg of pure U contains how many
atoms? (b) How much total energy is released if the entire mass of 1.00 kg of 33U fissions? (c) Suppose that these fission reactions occur at a rate to release a constant 100 W of power to a lamp for a long period of time. Assuming 100% of the reaction energy goes into powering the lamp, for how
many years can the lamp run?
A particular fission of a uranium-235 (235 U) nucleus, which has neutral atomic mass 235.0439 u, a reaction energy of 200 MeV is released.(a)1.00 kg of pure uranium contains approximately 2.56 x 10^24 uranium-235 atoms.(b)the total energy released if the entire mass of 1.00 kg of uranium-235 undergoes fission is approximately 3.11 x 10^13 joules.(c)assuming 100% of the reaction energy goes into powering the lamp, the lamp can run for approximately 983,544 years.
(a) To determine the number of uranium-235 (235U) atoms in 1.00 kg of pure uranium, we need to use Avogadro's number and the molar mass of uranium-235.
Calculate the molar mass of uranium-235 (235U):
Molar mass of uranium-235 = 235.0439 g/mol
Convert the mass of uranium to grams:
Mass of uranium = 1.00 kg = 1000 g
Calculate the number of moles of uranium-235:
Number of moles = (Mass of uranium) / (Molar mass of uranium-235)
Number of moles = 1000 g / 235.0439 g/mol
Use Avogadro's number to determine the number of atoms:
Number of atoms = (Number of moles) × (Avogadro's number)
Now we can perform the calculations:
Number of atoms = (1000 g / 235.0439 g/mol) × (6.022 x 10^23 atoms/mol)
Number of atoms ≈ 2.56 x 10^24 atoms
Therefore, 1.00 kg of pure uranium contains approximately 2.56 x 10^24 uranium-235 atoms.
(b) To calculate the total energy released if the entire mass of 1.00 kg of uranium-235 undergoes fission, we need to use the energy released per fission and the number of atoms present.
Given:
Reaction energy per fission = 200 MeV (mega-electron volts)
Convert the reaction energy to joules:
1 MeV = 1.6 x 10^-13 J
Energy released per fission = 200 MeV ×(1.6 x 10^-13 J/MeV)
Calculate the total number of fissions:
Total number of fissions = (Number of atoms) × (mass of uranium / molar mass of uranium-235)
Multiply the energy released per fission by the total number of fissions:
Total energy released = (Energy released per fission) × (Total number of fissions)
Now we can calculate the total energy released:
Total energy released = (200 MeV) * (1.6 x 10^-13 J/MeV) × [(2.56 x 10^24 atoms) × (1.00 kg / 235.0439 g/mol)]
Total energy released ≈ 3.11 x 10^13 J
Therefore, the total energy released if the entire mass of 1.00 kg of uranium-235 undergoes fission is approximately 3.11 x 10^13 joules.
(c) To calculate the number of years the lamp can run, we need to consider the power generated by the fission reactions and the total energy released.
Given:
Power generated = 100 W
Total energy released = 3.11 x 10^13 J
Calculate the time required to release the total energy at the given power:
Time = Total energy released / Power generated
Convert the time to years:
Time in years = Time / (365 days/year ×24 hours/day ×3600 seconds/hour)
Now we can calculate the number of years the lamp can run:
Time in years = (3.11 x 10^13 J) / (100 W) / (365 days/year × 24 hours/day * 3600 seconds/hour)
Time in years ≈ 983,544 years
Therefore, assuming 100% of the reaction energy goes into powering the lamp, the lamp can run for approximately 983,544 years.
To learn more about Avogadro's number visit: https://brainly.com/question/859564
#SPJ11
1. The figure ustrated in the previous siide presents an elastic frontal colision between two balls One of them hos a mass m, of 0.250 kg and an initial velocity of 5.00 m/s. The other has a mass of m, 0.800 kg and is initially at rest. No external forces act on the bolls. Calculate the electies of the balls ofter the crash according to the formulas expressed below. Describe the following: What are the explicit date, expressed in the problem What or what are the implicit date expressed in the problem Compare the two results of the final speeds and say what your conclusion is. 2 3 4. -1-+ Before collision m2 mi TOL 102=0 After collision in
The figure in the previous siide presents an elastic frontal collision between two balls One of them hos a mass m, of 0.250 kg and an initial velocity of 5.00 m/s 3.125 J = (0.125 kg) * (v1f^2) + (0.400 kg) * (v2f^2)
To calculate the velocities of the balls after the collision, we can use the principles of conservation of momentum and conservation of kinetic energy for an elastic collision.
Let the initial velocity of the first ball (mass m1 = 0.250 kg) be v1i = 5.00 m/s, and the initial velocity of the second ball (mass m2 = 0.800 kg) be v2i = 0 m/s.
Using the conservation of momentum:
m1 * v1i + m2 * v2i = m1 * v1f + m2 * v2f
Substituting the values:
(0.250 kg) * (5.00 m/s) + (0.800 kg) * (0 m/s) = (0.250 kg) * v1f + (0.800 kg) * v2f
Simplifying the equation:
1.25 kg·m/s = 0.250 kg·v1f + 0.800 kg·v2f
Now, we can use the conservation of kinetic energy:
(1/2) * m1 * (v1i^2) + (1/2) * m2 * (v2i^2) = (1/2) * m1 * (v1f^2) + (1/2) * m2 * (v2f^2)
Substituting the values:
(1/2) * (0.250 kg) * (5.00 m/s)^2 + (1/2) * (0.800 kg) * (0 m/s)^2 = (1/2) * (0.250 kg) * (v1f^2) + (1/2) * (0.800 kg) * (v2f^2)
Simplifying the equation:
3.125 J = (0.125 kg) * (v1f^2) + (0.400 kg) * (v2f^2)
Now we have two equations with two unknowns (v1f and v2f). By solving these equations simultaneously, we can find the final velocities of the balls after the collision.
To know more about collision refer here:
https://brainly.com/question/13138178#
#SPJ11
What is the weight of a 156O−kg car?
The weight of a 1560 kg car is approximately 15,317 Newtons (N). Weight is a measure of the force of gravity acting on an object, and it is calculated by multiplying the mass of the object by the acceleration due to gravity.
In this case, the mass of the car is 1560 kg. The standard acceleration due to gravity on Earth is approximately 9.8 m/s². By multiplying the mass (1560 kg) by the acceleration due to gravity (9.8 m/s²), we find that the weight of the car is approximately 15,317 N.
The weight of an object is directly proportional to its mass and the acceleration due to gravity. In this case, the mass of the car is given as 1560 kg. The acceleration due to gravity is a constant value on Earth, approximately 9.8 m/s².
To calculate the weight, we multiply the mass (1560 kg) by the acceleration due to gravity (9.8 m/s²). This yields a weight of approximately 15,317 N. Weight is a force, and it is measured in Newtons (N). Therefore, a 1560 kg car would weigh approximately 15,317 N on Earth.
Learn more about gravity click here:
brainly.com/question/31321801
#SPJ11
3. AIS MVX, 6.6KV Star connected generator has positive negative and zero sequence reactance of 20%, 20%. and 10. respect vely. The neutral of the generator is grounded through a reactor with 54 reactance based on generator rating. A line to line fault occurs at the terminals of the generator when it is operating at rated voltage. Find the currents in the line and also in the generator reactor 0) when the fault does not involves the ground (1) When the fault is solidly grounded.
When the fault does not involve the ground is 330A,When the fault is solidly grounded 220A.
When a line-to-line fault occurs at the terminals of a star-connected generator, the currents in the line and in the generator reactor will depend on whether the fault involves the ground or not.
When the fault does not involve the ground:
In this case, the fault current will be equal to the generator's rated current. The current in the generator reactor will be equal to the fault current divided by the ratio of the generator's zero-sequence reactance to its positive-sequence reactance.
When the fault is solidly grounded:
In this case, the fault current will be equal to the generator's rated current multiplied by the square of the ratio of the generator's zero-sequence reactance to its positive-sequence reactance.
The current in the generator reactor will be zero.
Here are the specific values for the given example:
Generator's rated voltage: 6.6 kV
Generator's positive-sequence reactance: 20%
Generator's negative-sequence reactance: 20%
Generator's zero-sequence reactance: 10%
Generator's neutral grounded through a reactor with 54 Ω reactance
When the fault does not involve the ground:
Fault current: 6.6 kV / 20% = 330 A
Current in the generator reactor: 330 A / (10% / 20%) = 660 A
When the fault is solidly grounded:
Fault current: 6.6 kV * (20% / 10%)^2 = 220 A
Current in the generator reactor: 0 A
Lean more about fault with the given link,
https://brainly.com/question/3088
#SPJ11
An object oscillates with simple harmonic motion along with x axis. Its displacement from the origin varies
with time according to the equation
x = (4.00m) cos( pi t + pi/4)
Where t is in seconds and the angles in the parentheses are in radians.
(a) Determine the amplitude, frequency and period of the motion.
(b) Calculate the velocity and acceleration of the object at time t.
(c) Using the results in part(b), determine the position, velocity and acceleration of the object at t = 1.0 s
(d) Determine the maximum speed and acceleration of the object.
(a) Amplitude: 4.00 m, Frequency: 0.5 Hz, Period: 2 seconds
(b) Velocity: -4.00 m/sin(πt + π/4), Acceleration: -4.00mπcos(πt + π/4)
(c) Position: 0.586 m, Velocity: -12.57 m/s, Acceleration: 12.57 m/s²
(d) Maximum speed: 12.57 m/s, Maximum acceleration: 39.48 m/s²
(a) Amplitude, A = 4.00 m
Frequency, ω = π radians/sec
Period, T = 2π/ω
Amplitude, A = 4.00 m
Frequency, f = ω/2π = π/(2π) = 0.5 Hz
Period, T = 2π/ω = 2π/π = 2 seconds
(b) Velocity, v = dx/dt = -4.00m sin(πt + π/4)
Acceleration, a = dv/dt = -4.00mπ cos(πt + π/4)
(c) At t = 1.0 s:
Position, x = 4.00 mcos(π(1.0) + π/4) ≈ 0.586 m
Velocity, v = -4.00 m sin(π(1.0) + π/4) ≈ -12.57 m/s
Acceleration, a = -4.00mπ cos(π(1.0) + π/4) ≈ 12.57 m/s²
(d) Maximum speed, vmax = Aω = 4.00 m * π ≈ 12.57 m/s
Maximum acceleration, amax = Aω² = 4.00 m * π² ≈ 39.48 m/s²
Learn more about Velocity at https://brainly.com/question/80295
#SPJ11
2. On the Season Finale of Keeping Up With The Gretta Bears: Gretta decides that she wants to go skiing in Aspen. When she gets there, she decides that snow is cold, her legs are short, and that skiing is so last year. With no need for her 10-kg skis anymore, she pushes them away at a speed of 12-m/s. The skis collide with 20-kg Buster and catch in his leash. Buster and the skis proceed to slide down a 30° slope of length 100-m. At the bottom of the slope, Buster is caught by a net attached to a spring with an effective spring constant of 500N/m. How far does the spring stretch before Buster momentarily comes to rest?
The spring stretches to 1.69 meters before Buster momentarily comes to rest.
How do we calculate?We find the initial kinetic energy of the skis before they collide with Buster:
Kinetic energy of skis = (1/2) * mass * velocity²
= (1/2) * 10 kg * (12 m/s)²
= 720 J
Change in height = height * sin(angle)
= 100 m * sin(30°)
= 50 m
The total initial gravitational potential energy is equal to the kinetic energy of the skis, since that Buster starts from rest = Initial potential energy = 720 J
The potential energy stored in the stretched spring :
= (1/2) * k * x²
720 J = (1/2) * 500 N/m * x²
1440 J = 500 N/m * x²
x² = (1440 J) / (500 N/m)
x² = 2.88 m
x = 1.69 m
Learn more about potential energy at:
https://brainly.com/question/14427111
#SPJ4
An object of mass 4.20 kg is projected into the air at a 55.0° angle. It hits the ground 3.40 s later. Set "up" to be the positive y direction. What is the y-component of the object's change in momentum while it is in the air? Ignore air resistance.
The y-component of the object's change in momentum while it is in the air is -139.944 Kg.m/s
How do i determine the y-component of change in momentum?First, we shall obtain the initial velocity. Details below:
Angle of projection (θ) = 55 ° Acceleration due to gravity (g) = 9.8 m/s²Time of flight (T) = 3.40Initial velocity (u) = ?T = 2uSineθ / g
3.40 = (2 × u × Sine 55) / 9.8
Cross multiply
2 × u × Sine 55 = 3.4 × 9.8
Divide both sides by (2 × Sine 55)
u = (3.4 × 9.8) / (2 × Sine 55)
= 20.34 m/s
Next, we shall obtain the initial and final velocity in the y-component direction. Details below:
For initial y-component:
Initial velocity (u) = 20.34 m/sAngle of projection (θ) = 55 °Initial y-component of velocity (uᵧ) =?uᵧ = u × Sine θ
= 20.34 × Sine 55
= 16.66 m/s
For final y-component:
Initial y-component of velocity (uᵧ) = 16.66 m/sAcceleration due to gravity (g) = 9.8 m/s²Time (t) = 3.4 sFinal y-component of velocity (vᵧ) =?vᵧ = uᵧ - gt
= 16.66 - (9.8 × 3.4)
= -16.66 m/s
Finally, we shall obtain the change in momentum. This is shown below:
Mass of object (m) = 4.20 KgInitial velocity (uᵧ) = 16.66 m/sFinal velocity (vᵧ) = -16.66Change in momentum =?Change in momentum = m(vᵧ - uᵧ)
= 4.2 × (-16.66 - 6.66)
= 4.2 × -33.32
= -139.944 Kg.m/s
Learn more about change in momentum:
https://brainly.com/question/21297884
#SPJ4
The magnetic force F' is always perpendicular to the acceleration a of the particle. T/F
True, the magnetic force F' is always perpendicular to the acceleration a of the particle.
True. According to the Lorentz force law, the magnetic force F' experienced by a charged particle moving in a magnetic field is given by F' = q(v × B), where q is the charge of the particle, v is its velocity, and B is the magnetic field.
Since the cross product v × B results in a vector perpendicular to both v and B, the magnetic force F' is always perpendicular to the velocity of the particle. Additionally, Newton's second law states that F' = ma, where m is the mass of the particle and a is its acceleration. Therefore, the magnetic force F' is always perpendicular to the acceleration a of the particle.
To learn more about magnetic field
Click here brainly.com/question/14848188
#SPJ11
Consider a sum J = L +5 of two angular momenta I and S. Consider a state J,m, with the maximal possible total angular momentum quantum number Jmax = L + S and m; = -Jmax. With the help of the rising ladder operator find the wave function Jmaz;-Jmaz+1, i.e. for the state with mj = - Jmax +1.
The wave function for the state J, m; = -Jmax + 1, where Jmax = L + S, can be obtained using the rising ladder operator.
The rising ladder operator, denoted as J+, is used to raise the value of the total angular momentum quantum number J by one unit. It is defined as J+|J, m> = √[J(J+1) - m(m+1)] |J, m+1>.
In this case, we are considering the state J, m; = -Jmax. To find the wave function for the state with m; = -Jmax + 1, we can apply the rising ladder operator once to this state.
Using the rising ladder operator, we have:
J+|J, m;> = √[J(J+1) - m(m+1)] |J, m; + 1>
Substituting the values, we get:
J+|-Jmax> = √[J(J+1) - (-Jmax)(-Jmax + 1)] |-Jmax + 1>
Since m; = -Jmax, the expression simplifies to:
J+|-Jmax> = √[J(J+1) - (-Jmax)(-Jmax + 1)] |-Jmax + 1>
We can express Jmax in terms of L and S:
Jmax = L + S
Substituting this into the equation, we have:
J+|-Jmax> = √[(L + S)(L + S + 1) - (-Jmax)(-Jmax + 1)] |-Jmax + 1>
Finally, we have the wave function for the state with m; = -Jmax + 1:
Jmaz;-Jmaz+1 = √[(L + S)(L + S + 1) - (-Jmax)(-Jmax + 1)] |-Jmax + 1>
Therefore, the wave function for the state with m; = -Jmax + 1 is given by Jmaz;-Jmaz+1 = √[(L + S)(L + S + 1) - (-Jmax)(-Jmax + 1)] |-Jmax + 1>.
For more such questions on wave function, click on:
https://brainly.com/question/30903926
#SPJ8
Green light has a wavelength of 5.20 × 10−7 m and travels through the air at a speed of 3.00 × 108 m/s.
Calculate the frequency of green light waves with this wavelength. Answer in units of Hz.
Calculate the period of green light waves with this wavelength. Answer in units of s.
To calculate the frequency of green light waves with a wavelength of 5.20 × 10^(-7) m, we can use the formula: Frequency (f) = Speed of light (c) / Wavelength (λ). Therefore, the period of green light waves with a wavelength of 5.20 × 10^(-7) m is approximately 1.73 × 10^(-15) s.
Plugging in the values:
Frequency = 3.00 × 10^8 m/s / 5.20 × 10^(-7) m
Frequency ≈ 5.77 × 10^14 Hz
Therefore, the frequency of green light waves with a wavelength of 5.20 × 10^(-7) m is approximately 5.77 × 10^14 Hz.
To calculate the period of green light waves with this wavelength, we can use the formula:
Period (T) = 1 / Frequency (f)
Plugging in the value of frequency:
Period = 1 / 5.77 × 10^14 Hz
Period ≈ 1.73 × 10^(-15) s
Therefore, the period of green light waves with a wavelength of 5.20 × 10^(-7) m is approximately 1.73 × 10^(-15) s.
To learn more about, frequency, click here, https://brainly.com/question/2140860
#SPJ11
A 1500-W wall mounted air conditioner is left on for 16 hours every day during a hot July (31 days in the month. If the cost of electricity is $0.12/kW.hr, how
much does it cost to run the air conditioner?
We are given that a 1500-W wall mounted air conditioner is left on for 16 hours every day during a hot July (31 days in the month) and the cost of electricity is $0.12/kW.hr.
To find the cost to run the air conditioner, we need to calculate the total energy consumed in 31 days and multiply it with the cost of electricity per unit. We know that Power = 1500 watts, Time = 16 hours/day, Days = 31 days in the month. Let's begin by calculating the total energy consumed. Energy = Power x Time= 1500 x 16 x 31= 744000 Wh.
To convert Wh to kWh, we divide by 1000.744000 Wh = 744 kWh. Now, let's calculate the cost to run the air conditioner. Total Cost = Energy x Cost per kWh= 744 x $0.12= $89.28.
Therefore, it will cost $89.28 to run the air conditioner for 16 hours every day during a hot July.
Let's learn more about Power:
https://brainly.com/question/11569624
#SPJ11
Calculate how many times you can travel around the earth using 1.228x10^2GJ with an E-scooter which uses 3 kWh per 100 km. Note that you can travel to the sun and back with this scooter using the energy of a whole year.
Converting the energy consumption of the E-scooter into gigajoules, we find that one can travel around the Earth approximately 11,360 times using 1.228x10^2 GJ of energy with the E-scooter.
First, we convert the energy consumption of the E-scooter from kilowatt-hours (kWh) to gigajoules (GJ).
1 kilowatt-hour (kWh) = 3.6 megajoules (MJ)
1 gigajoule (GJ) = 1,000,000 megajoules (MJ)
So, the energy consumption of the E-scooter per 100 km is:
3 kWh * 3.6 MJ/kWh = 10.8 MJ (megajoules)
Now, we calculate the number of trips around the Earth.
The Earth's circumference is approximately 40,075 kilometers.
Energy consumed per trip = 10.8 MJ
Total energy available = 1.228x10^2 GJ = 1.228x10^5 MJ
Number of trips around the Earth = Total energy available / Energy consumed per trip
= (1.228x10^5 MJ) / (10.8 MJ)
= 1.136x10^4
Therefore, approximately 11,360 times one can travel around the Earth using 1.228x10^2 GJ of energy with the E-scooter.
To know more about energy consumption, refer to the link :
https://brainly.com/question/30125850#
#SPJ11
A cat with mass mk = 5.00 kg sits on a swing that has mass mh = 1.50 kg. Ignore the mass of the ropes that hold the swing up. Suddenly a dog appears, and the cat jumps down from the swing to hide. As the cat jumps off, the swing swings backwards. Assume that the cat jumps out horizontally and that both the cat and the swing are particles. Ignore all forms of friction. - Find the speed of the cat as it leaves the swing when you know that the height h = 0.545 m and that the horizontal distance s = 0.62 m. - Use the result above to find out how high above its lowest point the swing can get. If you have not solved the part, you can set up and justify the equations that must be used. = = -
The speed of the cat as it leaves the swing when you know that the height h = 0.545 m and that the horizontal distance s = 0.62 m is 2.866 m/s and the maximum height is 0.419 m.
Speed of the cat as it leaves the swing:
To find the speed of the cat, we can use the principle of conservation of mechanical energy. Initially, the system (cat + swing) has gravitational potential energy, which is converted into kinetic energy as the cat jumps off the swing.
Using the conservation of mechanical energy equation:
[tex]m_k gh=0.5(m_k+m_h)v^{2} \\5 \times 9.8 \times 0.545=0.5(5.00+1.50)v^{2} \\26.705=3.25 v^{2}\\\8.2169=v^{2}\\ v=\sqrt{8.2169} \\v=2.866 m/s[/tex]
where [tex]m_k[/tex] is the mass of the cat, [tex]m_h[/tex] is the mass of the swing, g is the acceleration due to gravity, h is the height, and v is the speed of the cat.
Therefore,the speed of the cat is found to be 2.866 m/s.
Maximum height of the swing:
Using the principle of conservation of mechanical energy, we can also determine the maximum height the swing can reach. At the highest point, the swing has only potential energy, which is equal to the initial gravitational potential energy.
Using the conservation of mechanical energy equation:
[tex]0.5(m_k+m_h)v^{2}=(m_k+m_h)gH_m_a_x\\[/tex]
where [tex]H_m_a_x[/tex] is the maximum height the swing can reach.
So, [tex]H_m_a_x[/tex] will be,
[tex]0.5(5.00+1.50)v^{2} \times 8.2169=(5.00+1.05) \times 9.8 \times H_m_a_x\\ 26.70=63.7H_m_a_x\\H_m_a_x=0.419 m[/tex]
Thus,the maximum height is 0.419 m.
In conclusion,The speed of the cat as it leaves the swing is 2.866 m/s and the maximum height is 0.419 m.
Learn more about speed here: brainly.com/question/27888149
#SPJ11
Consider the electron wave function Sovi-x² 1 x s 1 cm ¥(x) = 10 |x 21 cm • Determine the normalization constant c. • Draw a graph of 4(2) over the interval-2cm
The normalization constant (C) does not exist as the integral value goes to infinity, which means that Ψ(x) is not normalizable.
Electron wave function, Ψ(x) = 10|x - 21cm|² (s / cm). The normalization constant for the wave function is defined as follows:∫|Ψ(x)|² dx = 1Normalization Constant (C)C = √(∫|Ψ(x)|² dx)Here, Ψ(x) = 10|x - 21cm|² (s / cm)C = √(∫|10|x - 21cm|²|² dx)By substituting the value of |10|x - 21cm|²|², we get,C = √(10²∫|x - 21cm|⁴ dx)C = √[10² ∫(x² - 42x + 441) dx]C = √[10² ((x³/3) - 21x² + 441x)]Upper Limit = x = + ∞Lower Limit = x = - ∞C = √[10² {(+∞³/3) - 21(+∞²) + 441(+∞)} - 10² {(-∞³/3) - 21(-∞²) + 441(-∞)}]C = √0 - ∞C = ∞The normalization constant (C) does not exist as the integral value goes to infinity, which means that Ψ(x) is not normalizable.
Graph of Ψ(x) is shown below:Explanation of the graph: The wave function |Ψ(x)|² goes to infinity as x goes to infinity and to the left of x = 21cm it is zero. At x = 21cm, there is a discontinuity in the graph and it goes to infinity after that.
Learn more about normalization constant :
https://brainly.com/question/32119728
#SPJ11
You generate a sound wave of 420 Hz with a speaker. The speed of sound is 342 m/s.
What is the wavelength of the sound?
Question 1 options:
143640 m
1.23 m
0.814 m
You generate a sound wave of 420 Hz with a speaker. The speed of sound is 342 m/s.
You are 2 m from the speaker. You hear a loudness of 48 dB. You back up until you are 4 m away. The loudness you hear now is
Question 2 options:
24 dB
12 dB
45 dB
42 dB
A police car with its siren emitting sound at 440 Hz is moving away from you at 30 m/s. The frequency of the sound you hear is
Question 3 options:
440 Hz
less than 440 Hz
greater than 440 Hz
impossible to tell
Some red light has a wavelength of 620 nm (nanometers).
Some blue light has wavelength 460 nm. Is it faster, slower, or the same speed as the red light?
Question 4 options:
faster
slower
same speed
The colors of light differ in their wavelengths, not in their speed. Hence, red and blue light have the same speed in a vacuum.
1. We can use the equation:v = fλWhere v = speed of sound, f = frequency of the sound wave and λ = wavelength of the sound wave. Here,
v = 342 m/s
f = 420 Hzλ
= v/f
λ = v/f
= 342/420
= 0.814 m
Hence, the wavelength of the sound wave is 0.814 m
.2. The loudness of sound depends on the distance between the source and the listener. The inverse-square law states that the intensity of sound waves reduces as the distance between the listener and the source increases. The loudness of sound decreases by 6 dB when the distance is doubled. Hence, when the distance is halved, the loudness increases by 6 dB. We can use this law to solve this problem. Let's say the loudness at a distance of 2 m is x dB. Then, the loudness at a distance of 4 m would be (x - 6) dB. From the given data, we know that:
x - 6 = 48 - 6 = 42 dB
Therefore, the loudness at a distance of 4 m would be 42 dB.
3. When a sound source moves towards a stationary observer, the frequency of the sound waves received by the observer increases. Similarly, when the sound source moves away from the observer, the frequency of the sound waves received by the observer decreases. This phenomenon is called the Doppler effect. The Doppler effect formula is:
f = f0(v + vo) / (v + vs)
where f0 is the frequency emitted by the source, f is the frequency received by the observer, v is the speed of sound, vo is the velocity of the observer and vs is the velocity of the source. In this case, the frequency emitted by the source (police car) is 440 Hz. The velocity of sound (v) is 342 m/s. The car is moving away from you, so vs is negative. Therefore, we can use the following equation:
f = f0(v - vo) / (v - vs)
f = 440(342 - 30) / (342 + 0)
f = 397.2 Hz
Therefore, the frequency of the sound you hear is less than 440 Hz.
4. The speed of light is constant in a vacuum and is approximately 3 × 10⁸ m/s. The speed of light in air, water, or any other medium is slower than its speed in a vacuum. However, the speed of different colors of light in a vacuum is the same. The colors of light differ in their wavelengths, not in their speed. Hence, red and blue light have the same speed in a vacuum.
To know more about wavelengths visit:
https://brainly.com/question/31143857
#SPJ11
A fluid of specific gravity 1.0 is flowing through a horizontal conduit at a velocity 2.0 m/s before descending 11 m to a lower portion of the conduit where it travels horizontally at 9.0 m/s. What is the pressure difference (P_lower- P−upper) between the lower portion and the upper portion of the conduit? Your Answer: Answer units
The pressure difference (P2 - P1) between the lower portion and the upper portion of the conduit is -38,555 Pa.
Given data: Specific gravity (SG) = 1.0
Velocity at upper portion (V1) = 2.0 m/s
Distance from upper portion (H1) = 0 m
Velocity at lower portion (V2) = 9.0 m/s
Distance from lower portion (H2) = 11 m
To find: Pressure difference (P2 - P1) between the lower portion and the upper portion of the conduit
Formula used:P + (1/2)ρV² + ρgh = constant Where, P = pressureρ = density
V = velocityg = acceleration due to gravity
h = height
Let's consider upper portion,
Using the above-mentioned formula:P1 + (1/2)ρV1² + ρgH1 = constant -----(1)
P1 = constant - (1/2)ρV1² - ρgH1P1 = constant - (1/2)ρ
V1² - ρg(0) //
At upper portion, height (H1) = 0, g= 9.81 m/s²P1 = constant - (1/2)ρV1² -------(2)
Let's consider the lower portion:Using the above-mentioned formula:
P2 + (1/2)ρV2² + ρgH2 = constant ----- (3)
P2 = constant - (1/2)ρV2² - ρgH2 -------(4)
Subtracting equation (2) from equation (4), we get,
P2 - P1 = - 1/2 ρ (V2² - V1²) + ρg (H2 - H1)
= - 1/2 ρ (9.0 m/s)² - (2.0 m/s)² + ρg (11 m - 0 m)
= -0.5 ρ (81 - 4) + ρg (11)
= -0.5 × 1000 × 77 + 9.81 × 11
= -38,555 Pa
Therefore, the pressure difference (P2 - P1) between the lower portion and the upper portion of the conduit is -38,555 Pa.
Learn more about pressure difference
brainly.com/question/13390708
#SPJ11
c).i. A conductor transfers heat of 3000 J across its length of 20cm in 6 seconds. Given that its cross-sectional area A is 55cm². Determine the thermal conductivity of the material if the temperature difference across the ends is 67°C? ii. An object of emissivity 0.7 and cross-sectional area 55mm? at room temperature of 30° losses energy at a rate of 35.6 J/s. What is the initial 2 2/7 temperature of the object? [ hint; stefan's constant o = 5.6703 x10- 8W/m/K+ ]
The thermal conductivity of the material is 0.238 W/m°C and the initial temperature of the object is 209°C.
i. Length of the conductor, L = 20 cm = 0.2 m
Time taken, t = 6 s
Cross-sectional area, A = 55 cm² = 55 × 10⁻⁴ m²
Heat transferred, Q = 3000 J
Temperature difference, ΔT = 67°C
Thermal conductivity of the material, K = ?
Formula used: Heat transferred, Q = K × A × ΔT ÷ L
where Q is the heat transferred, K is the thermal conductivity of the material, A is the cross-sectional area, ΔT is the temperature difference and L is the length of the conductor.
So, K = Q × L ÷ A × ΔT
Substituting the given values, we get,
K = 3000 J × 0.2 m ÷ (55 × 10⁻⁴ m²) × 67°C
K = 0.238 W/m°C
ii. Area of the object, A = 55 mm²
= 55 × 10⁻⁶ m²
Emissivity of the object, ε = 0.7
Rate of energy loss, P = 35.6 J/s
Stefan's constant, σ = 5.6703 × 10⁻⁸ W/m²/K⁴
Initial temperature, T₁ = ?
Formula used: Rate of energy loss, P = ε × σ × A × (T₁⁴ - T₂⁴)
where P is the rate of energy loss, ε is the emissivity of the object, σ is the Stefan's constant, A is the area of the object, T₁ is the initial temperature and T₂ is the final temperature.
So, P = ε × σ × A × (T₁⁴ - T₂⁴)
Solving the above equation for T₁, we get
T₁⁴ - T₂⁴ = P ÷ (ε × σ × A)
T₁⁴ = (P ÷ (ε × σ × A)) + T₂
⁴T₁ = [ (P ÷ (ε × σ × A)) + T₂⁴ ]¹∕⁴
Substituting the given values, we get,
T₁ = [ (35.6 J/s) ÷ (0.7 × 5.6703 × 10⁻⁸ W/m²/K⁴ × 55 × 10⁻⁶ m²) + (30 + 273)⁴ ]¹∕⁴
T₁ = 481.69 K
≈ 208.69°C
≈ 209°C (approx.)
Therefore, the thermal conductivity of the material is 0.238 W/m°C and the initial temperature of the object is 209°C.
To know more about thermal conductivity, visit:
https://brainly.com/question/14553214
#SPJ11
An electron is shot vertically upward through the tiny holes in the center of a parallel-plate capacitor. If the initial speed of the electron at the hole in the bottom plate of the capacitor is 4.00
Given Data: The initial speed of the electron at the hole in the bottom plate of the capacitor is 4.00.What is the final kinetic energy of the electron when it reaches the top plate of the capacitor? Explanation: The potential energy of the electron is given by, PE = q V Where q is the charge of the electron.
V is the potential difference across the capacitor. As the potential difference across the capacitor is constant, the potential energy of the electron will be converted to kinetic energy as the electron moves from the bottom to the top of the capacitor. Thus, the final kinetic energy of the electron is equal to the initial potential energy of the electron. K.E = P.E = qV Thus, K.E = eV Where e is the charge of the electron. K.E = 1.60 × 10-19 × 1000 × 5K.E = 8 × 10-16 Joule, the final kinetic energy of the electron when it reaches the top plate of the capacitor is 8 × 10-16 Joule.
To know more about energy visit:
https://brainly.com/question/1932868
#SPJ11