A 97 kg person receives a whole-body radiation dose of 1.9 x 10⁻⁴Gy, delivered by alpha particles for which the RBE factor is 13. Calculate (a) the absorbed energy and the dose equivalent in (b) sieverts and (c) rem.
(a) Number ____________ Units ____________
(b) Number ____________ Units ____________
(c) Number ____________ Units ____________

Answers

Answer 1

(a) The number of absorbed energy is calculated to be 0.24033 J. The units for absorbed energy are joules (J). (b) The dose equivalent is calculated to be 0.00247 Sv. The units for dose equivalent are sieverts (Sv). (c) The dose equivalent in rem is 0.247 rem. The units for dose equivalent in rem is rem.

(a) The absorbed energy can be calculated by multiplying the absorbed dose, RBE factor, and mass of the person. In this case, the absorbed energy is found to be 0.24033 J.

(b) The dose equivalent is obtained by multiplying the absorbed dose and the quality factor. For alpha radiation, the quality factor is 13. Thus, the dose equivalent is calculated as 0.00247 Sv.

(c) The dose equivalent in rem is derived by converting Sv to rem. To convert, the dose equivalent in Sv is multiplied by 100. Therefore, the dose equivalent in rem is found to be 0.247 rem.

In summary, the absorbed energy is 0.24033 J, the dose equivalent is 0.00247 Sv, and the dose equivalent in rem is 0.247 rem.

Learn more about energy at: https://brainly.com/question/2003548

#SPJ11


Related Questions

1. An car’s engine idles at 1200 rpm. Determine the
frequency in hertz. 2. What would be the frequency of a space-station
spinning at 120o per second?

Answers

The car engine idling at 1200 rpm has a frequency of 20 Hz. The space-station spinning at 120 degrees per second has a frequency of approximately 0.333 Hz.

To determine the frequency in hertz, we need to convert the rotations per minute (rpm) to rotations per second. We can use the following formula:

Frequency (in hertz) = RPM / 60

For the car engine idling at 1200 rpm:

Frequency = 1200 / 60 = 20 hertz

For the space-station spinning at 120 degrees per second, we need to convert the degrees to rotations before calculating the frequency. Since one complete rotation is equal to 360 degrees, we can use the following formula:

Frequency (in hertz) = Rotations per second = Degrees per second / 360

For the space-station spinning at 120 degrees per second:

Frequency = 120 / 360 = 1/3 hertz or approximately 0.333 hertz

Therefore, the frequency of the car engine idling at 1200 rpm is 20 hertz, while the frequency of the space-station spinning at 120 degrees per second is approximately 0.333 hertz.

To know more about rotations per minute,

https://brainly.com/question/927364

#SPJ11

A) A positively charged balloon is brought near an originally uncharged conductor. The balloon does not touch the conductor. Does the conductor acquire a net charge? B) A positively charged balloon is brought near an originally uncharged conductor. The balloon does not touch the conductor. Does the conductor begin to cause electric fields at points external to the conductor? Explain

Answers

As the balloon moves closer to the conductor, the electric field strength will increase and charges will continue to be redistributed.

A) When a positively charged balloon is brought near an originally uncharged conductor, the conductor does acquire a net charge but not an equal one to that of the balloon. This is due to the fact that the conductor and balloon have different charges and therefore, when the conductor is brought near the balloon, the electrons move within the conductor leading to a net charge. When the balloon is brought near the conductor, the positively charged balloon will polarize the conductor, attracting electrons from one side and repelling them from the other side.

This will cause a net charge to be induced in the conductor due to the movement of the electrons, even if the balloon doesn't touch the conductor. This movement of electrons can result in the production of an electric current, but the amount of charge on the conductor will be less than the amount of charge on the balloon.

B) Yes, the conductor will begin to cause electric fields at points external to the conductor. This is because the positively charged balloon will cause the conductor to polarize and create an electric field in thesurrounding area.

Since the balloon and the conductor have different charges, an electric field will be induced in the area around the conductor, causing charges to be redistributed in that region. The strength of the electric field will be proportional to the magnitude of the charge on the balloon and the distance between the balloon and the conductor. Therefore, as the balloon moves closer to the conductor, the electric field strength will increase and charges will continue to be redistributed.

Learn more about Electric here,

https://brainly.com/question/776932

#SPJ11

What is the pressure inside a 32.0 L container holding 104.1 kg of argon gas at 20.3°C?

Answers

The pressure inside the 32.0 L container holding 104.1 kg of argon gas at 20.3°C is approximately 67279.93 Pa.

To calculate the pressure inside a container of gas, we can use the ideal gas law equation:

PV = nRT

Where:

P is the pressure of the gas

V is the volume of the container

n is the number of moles of gas

R is the ideal gas constant (8.314 J/(mol·K))

T is the temperature in Kelvin

First, let's convert the given temperature from Celsius to Kelvin:

T = 20.3°C + 273.15 = 293.45 K

Next, we need to determine the number of moles of argon gas using the molar mass of argon (Ar), which is approximately 39.95 g/mol.

n = mass / molar mass

n = 104.1 kg / (39.95 g/mol * 0.001 kg/g)

n = 2604.006 moles

Now, we can substitute the values into the ideal gas law equation to solve for the pressure:

P * 32.0 L = (2604.006 mol) * (8.314 J/(mol·K)) * 293.45 K

P = (2604.006 * 8.314 * 293.45) / 32.0

P ≈ 67279.93 Pa

To know more about ideal gas law

https://brainly.com/question/30458409

#SPJ11

"Charging" the magnetic field of an inductor 60.000 m of wire is wound on a cylinder, tight packed and without any overlap, to a diameter of 2.00 cm (relenoid 0.0100 m ). The wire has a radius of rune −0.00100 m and a total resistance of 0.325Ω. This inductor initially has no current flowing in it. It is suddenly connected to a DC voltage source at time t−0.000sec. V s

=2.00Volts. After 2 time constants, the current across the inductor will be.... Hint: first find the inductor currents I t=[infinity]

I F=[infinity]

Answers

After 2 time constants, the current across the inductor will be approximately 5.320 Amperes. The current across the inductor after 2 time constants, we need to calculate the time constant and then use it to find the current at that time. The time constant (τ) of an RL circuit (resistor-inductor circuit) is given by the formula:

τ = L / R,

where L is the inductance and R is the resistance.

First, let's calculate the inductance of the coil. The inductance of a tightly packed solenoid can be approximated using the formula:

L = (μ₀ * N² * A) / l,

where μ₀ is the permeability of free space (4π x [tex]10^-7[/tex]T·m/A), N is the number of turns, A is the cross-sectional area of the solenoid, and l is the length of the solenoid.

Number of turns, N = 60,000

Cross-sectional area, A = π * ([tex]0.0200 m)^2[/tex]

Length of the solenoid, l = 0.0100 m

Using these values, we can calculate the inductance:

L = (4π x [tex]10^-7[/tex]T·m/A) * ([tex]60,000 turns)^2[/tex] * (π * [tex](0.0200 m)^2[/tex]) / 0.0100 m

≈ 0.301 T·m²/A

Next, we can calculate the time constant:

τ = L / R = 0.301 T·m²/A / 0.325 Ω

≈ 0.926 s

Now, we can determine the current after 2 time constants:

I(t) = I(∞) * (1 - e^(-t/τ)),

where I(t) is the current at time t, I(∞) is the final current (as t approaches infinity), and e is the base of the natural logarithm.

Since t = 2τ, we can substitute this value into the equation:

I(2τ) = I(∞) * (1 - e^(-2))

≈ I(∞) * (1 - 0.1353)

≈ I(∞) * 0.8647

We are given that the voltage source is 2.00 Volts. Using Ohm's law (V = I(∞) * R), we can solve for I(∞):

2.00 V = I(∞) * 0.325 Ω

I(∞) = 2.00 V / 0.325 Ω

≈ 6.153 A

Finally, we can calculate the current after 2 time constants:

I(2τ) ≈ I(∞) * 0.8647

≈ 6.153 A * 0.8647

≈ 5.320 A

Therefore, after 2 time constants, the current across the inductor will be approximately 5.320 Amperes.

Learn more about current here:

https://brainly.com/question/13757528

#SPJ11

LR.pdf R = 200 H, L=5 mH calulate the cut off frequency Fe Consider the following circuit, L m 7₂ To R = 200 £2, How to choose L if of cut off frequency F=3000Hz

Answers

If the cutoff frequency (Fc) is 3000 Hz and the resistance (R) is 200 Ω, the required value of inductance (L) is approximately 1.33 mH.

To calculate the cutoff frequency (Fc) of a circuit with an inductor (L) and a resistor (R), we can use the formula:

Fc = 1 / (2π√(L * R))

Given that R = 200 Ω and Fc = 3000 Hz, we can rearrange the formula to solve for L:

L = (1 / (4π² * Fc² * R))

Substituting the values:

L = (1 / (4π² * (3000 Hz)² * 200 Ω))

L ≈ 1.33 mH

Therefore, if the cutoff frequency (Fc) is 3000 Hz and the resistance (R) is 200 Ω, the required value of inductance (L) is approximately 1.33 mH.

To know more about cutoff frequency (Fc) click here:

https://brainly.com/question/15711500

#SPJ11

How do I derive the formula for the magnetic field at a point
near infinite and semi-infinite long wire using biot savart's
law?

Answers

To derive the formula for the magnetic field at a point near an infinite and semi-infinite long wire using Biot-Savart's law.

Follow these steps:  the variables, Express Biot-Savart's law, the direction of the magnetic field,  an infinite long wire and a semi-infinite long wire.

Define the variables:

I: Current flowing through the wire

dl: Infinitesimally small length element along the wire

r: Distance between the point of interest and the current element dl

θ: Angle between the wire and the line connecting the current element to the point of interest

μ₀: Permeability of free space (constant)

Express Biot-Savart's law:

B = (μ₀ / 4π) * (I * dl × r) / r³

This formula represents the magnetic field generated by an infinitesimal current element dl at a distance r from the wire.

Determine the direction of the magnetic field:

The magnetic field is perpendicular to both dl and r, and follows the right-hand rule. It forms concentric circles around the wire.

Consider an infinite long wire:

In the case of an infinite long wire, the wire extends infinitely in both directions. The current is assumed to be uniform throughout the wire.

The contribution to the magnetic field from different segments of the wire cancels out, except for those elements located at the same distance from the point of interest.

By symmetry, the magnitude of the magnetic field at a point near an infinite long wire is given by:

B = (μ₀ * I) / (2π * r)

This formula represents the magnetic field at a point near an infinite long wire.

Consider a semi-infinite long wire:

In the case of a semi-infinite long wire, we have one end of the wire located at the point of interest, and the wire extends infinitely in one direction.

The contribution to the magnetic field from segments of the wire located beyond the point of interest does not affect the field at the point of interest.

By considering only the current elements along the finite portion of the wire, we can derive the formula for the magnetic field at a point near a semi-infinite long wire.

The magnitude of the magnetic field at a point near a semi-infinite long wire is given by:

B = (μ₀ * I) / (2π * r)

This formula is the same as that for an infinite long wire.

By following these steps, we can derive the formula for the magnetic field at a point near an infinite and semi-infinite long wire using Biot-Savart's law.

To know more about Biot-Savart's law

https://brainly.com/question/1120482

#SPJ11

True or false: A. Hot objects are bluer than cold objects B.The radius of the 3M orbit of Helium is bigger than 10th orbit of Boron (single electron atoms) C. If you raise the temperature of a block body by a factor of 3 is it 9 times brighter D. decay involves a position E. decay shows that there are only some allowed electron orbits in an atom F. decay happens when a proton tums into a neutron G. decay involves a Helium nucleus

Answers

Answer: A. False  B. True  C. True  D. False  E. False  F. False  G. True

Explanation:

A. False: Hot objects are not bluer than cold objects. Hot objects actually glow red, yellow or blue, depending on how hot they are.

B. True: As the radius of an electron orbit in an atom is proportional to n2, the radius of the 3M orbit of Helium (n = 3) is greater than the radius of the 10th orbit of Boron (n = 10).

C. True: If we increase the temperature of a body by a factor of 3, the power of emitted radiation increases by 34 or 81. Therefore, the brightness increases by a factor of 81.

D. False: Decay does not involve a position.

E. False: Decay does not show that there are only some allowed electron orbits in an atom.

F. False: Decay does not happen when a proton turns into a neutron.

G. True: Alpha decay, also known as decay, is the process in which a Helium nucleus is emitted.

Learn more about Decay : https://brainly.com/question/9932896

#SPJ11

A monochromatic source emits a 6.3 mW beam of light of wavelength 600 nm. 1. Calculate the energy of a photon in the beam in eV. 2. Calculate the number of photons emitted by the source in 10 minutes. The beam is now incident on the surface of a metal. The most energetic electron ejected from the metal has an energy of 0.55 eV. 3. Calculate the work function of the metal.

Answers

The power emitted by a monochromatic source is 6.3 m Wavelength of light emitted by the source is 600 nm.

1. Energy of photon, E = hc/λ

where, h = Planck's constant = 6.63 × 10⁻³⁴ Js, c = Speed of light = 3 × 10⁸ m/s, λ = wavelength of light= 600 nm = 600 × 10⁻⁹ m

Substitute the values, E = (6.63 × 10⁻³⁴ J.s × 3 × 10⁸ m/s)/(600 × 10⁻⁹ m) = 3.31 × 10⁻¹⁹ J1 eV = 1.6 × 10⁻¹⁹ J

Hence, Energy of photon in eV, E = (3.31 × 10⁻¹⁹ J)/ (1.6 × 10⁻¹⁹ J/eV) = 2.07 eV (approx.)

2. The power is given by,

P = Energy/Time Energy, E = P × Time Where P = 6.3 mW = 6.3 × 10⁻³ W, Time = 10 minutes = 10 × 60 seconds = 600 seconds

E = (6.3 × 10⁻³ W) × (600 s) = 3.78 J

Number of photons emitted, n = E/Energy of each photon = E/E1 = 3.78 J/3.31 × 10⁻¹⁹ J/photon ≈ 1.14 × 10²¹ photons

3. The work function (ϕ) of a metal is the minimum energy required to eject an electron from the metal surface. It is given by the relation, K max = hv - ϕ where Kmax = Maximum kinetic energy of the ejected electron, v = Frequency of the incident radiation (v = c/λ), and h = Planck's constant.

Using Kmax = 0.55 eV = 0.55 × 1.6 × 10⁻¹⁹ J, h = 6.63 × 10⁻³⁴ Js, λ = 600 nm = 600 × 10⁻⁹ m,v = c/λ = 3 × 10⁸ m/s ÷ 600 × 10⁻⁹ m = 5 × 10¹⁴ s⁻¹.

Substituting all the values in the above formula,ϕ = hv - Kmaxϕ = (6.63 × 10⁻³⁴ Js × 5 × 10¹⁴ s⁻¹) - (0.55 × 1.6 × 10⁻¹⁹ J)ϕ ≈ 4.3 × 10⁻¹⁹ J

Therefore, the work function of the metal is approximately equal to 4.3 × 10⁻¹⁹ J.

Explore another question on work function of metals: https://brainly.com/question/19427469

#SPJ11

Find solutions for your homework
science
earth sciences
earth sciences questions and answers
the ochre sea star (pisaster ochraceus), has radial symmetry with a flat, star shaped body with five spokes radiating from its center place. it is in what class? gastropoda polyplacophora
Question: The Ochre Sea Star (Pisaster Ochraceus), Has Radial Symmetry With A Flat, Star Shaped Body With Five Spokes Radiating From Its Center Place. It Is In What Class? Gastropoda Polyplacophora
The ochre sea star (Pisaster ochraceus), has radial symmetry with a flat, star shaped body with five spokes radiating from its center place. It is in what class?
Gastropoda
Polyplacophora
Asteroidea
Anthozoa
Echinoidea

Answers

The ochre sea star (Pisaster ochraceus) belongs to the Asteroidea class of the phylum Echinodermata. It is characterized by its radial symmetry and has a flat, star-shaped body with five spokes radiating from its center.

Asteroidea is a class within the phylum Echinodermata, which includes starfish or sea stars. Animals in the Asteroidea class have five or more arms that radiate from a central disk. They can be found in various marine habitats across the world's oceans, ranging from the deep sea to intertidal zones.

Apart from Asteroidea, the phylum Echinodermata also includes other classes such as Crinoidea (sea lilies and feather stars), Echinoidea (sea urchins and sand dollars), Holothuroidea (sea cucumbers), and Ophiuroidea (brittle stars and basket stars). Each class within the phylum exhibits unique characteristics and adaptations for their specific habitats and lifestyles.

Learn more about ochre sea star

https://brainly.com/question/30093147

#SPJ11

Which pairs of angles must atways be the same? Select one: a. Angle of incidence and angle of reflection b. Angle of incidence and angle of refraction c. Angle of reflection and angle of refraction d. Angle of incidence and angle of diffraction Two waves cross and result in a wave with a targer amplitude than either of the originat waves, This is called Select one: a. phase exchange b. negative superimposition c. destructive interference d. constructive interference

Answers

The angles that must always be the same are the angle of incidence and the angle of reflection (a). When two waves cross and result in a wave with a larger amplitude than either of the original waves, it is called constructive interference (d).

(a) The angle of incidence and the angle of reflection must always be the same. According to the law of reflection, when a wave reflects off a surface, the angle at which it strikes the surface (angle of incidence) is equal to the angle at which it bounces off (angle of reflection). This holds true for all types of surfaces, whether they are smooth or rough.

(d) When two waves cross and their amplitudes add up to create a wave with a larger amplitude than either of the original waves, it is called constructive interference. In constructive interference, the crests of one wave align with the crests of the other wave, resulting in reinforcement and an increase in amplitude. This occurs when the waves are in phase, meaning their peaks and troughs align.

Therefore, the correct answer is: Angle of incidence and angle of reflection must always be the same (a), and when two waves cross and result in a wave with a larger amplitude, it is called constructive interference (d).

Learn more about reflection here:

https://brainly.com/question/32190023

#SPJ11

A 10-KVA 500/250-V 50 Hz, single-phase transformer has the following parameters R₁ = 042, R₂ = 0 1 0, X₁ = 20 and X₂= 0 5 0. Determine the full load readings on the voltmeter, ammeter and watt-meter for the short circuit test by shorting the low voltage winding. 71 IFL - The primary full load current. 72 7.3 74 Ret - The equivalent resistance, referred to primary side Xe1 The equivalent reactance, referred to primary side Ze1- The equivalent impedance, referred to primary side Vsc (Voltmeter reading) 7.6 Isc (Ammeter reading) 7.7 Psc (Wattmeter reading)

Answers

The full load readings on the voltmeter, ammeter and watt-meter for the short circuit test by shorting the low voltage winding. Vsc (Voltmeter reading)= 250 VISc, Ammeter reading)= 7.6 APsc, (Wattmeter reading)= 440 W is the answer.

In order to determine the full load readings on the voltmeter, ammeter and watt-meter for the short circuit test by shorting the low voltage winding, the given values should be utilized. The values of parameters given are: R₁ = 0.42, R₂ = 1.0, X₁ = 20, and X₂ = 0.50.

The Short circuit test is performed on the low-voltage (secondary) side of the transformer. Due to the short circuit, the secondary voltage drops to zero and hence the entire primary voltage appears across the impedance referred to as the primary. The full load readings on the voltmeter, ammeter and watt-meter for the short circuit test by shorting the low voltage winding can be calculated as follows:

Where Vsc= Voltmeter reading = 250

VIsc= Ammeter reading = 7.6

APsc= Wattmeter reading = 440

WZ= Impedance referred to primary side

= [tex]{{Z}_{1}}+{{Z}_{2}}[/tex]

= 0.42 + j20 + 1.0 + j0.5

= [tex]1.42 + j20.5[tex]I_{FL}[/tex]

=[tex]\frac{{{V}_{1}}}{\sqrt{3}{{Z}_{1}}}\,\,[/tex]

=[tex]\frac{500}{\sqrt{3}\left( 0.42+j20 \right)}[/tex][/tex]

= 7.06 A

The full load readings on the voltmeter, ammeter and watt-meter for the short circuit test by shorting the low voltage winding are as follows: 71 IFL - The primary full load current= 7.06 A72 7.3 74 Ret - The equivalent resistance, referred to as the primary side Xe1= R2= 1 Ω

The equivalent reactance, referred to as the primary side Ze1= X2= 0.5 Ω

The equivalent impedance, referred to the primary side Z = R + jX = 1 + j0.5= 1.118Ω

Vsc (Voltmeter reading)= 250 VISc (Ammeter reading)= 7.6 APsc (Wattmeter reading)= 440 W

know more about equivalent impedance,

https://brainly.com/question/31770436

#SPJ11

High frequency alternating current is passed through a solenoid that contains a solid copper core insulated from the coils of the solenoid. Which statement is correct? O A copper core remains cool no matter what the frequency of the current in the solenoid is. The copper core remains cool because the induced emf is parallel to the solenoid axis and fluctuates rapidly. 0 The copper core heats up because an emf parallel to the solenoid axis is induced in the core. O The copper core heats up because circular currents around its axis are induced in the core. O The copper core heats up because the electric field induced in the copper is parallel to the magnetic field produced by the solenoid.

Answers

The correct statement is that c. the copper core heats up because circular currents around its axis are induced in the core.

What is a solenoid?

A solenoid is a long coil of wire with numerous turns that are tightly packed together. It produces a uniform magnetic field when electrical energy is passed through it. An electric current flowing through a solenoid produces a magnetic field that is proportional to the number of turns in the coil and the magnitude of the electric current.

The statement, "The copper core heats up because circular currents around its axis are induced in the core" is correct. The magnetic field produced by the solenoid induces circular currents in the copper core. These circular currents are referred to as eddy currents. The eddy currents heat up the copper core and, as a result, the copper core becomes hot.

To learn more circular currents, refer:-

https://brainly.com/question/30874979

#SPJ11

Photons of wavelength 450 nm are incident on a metal. The most energetic electrons ejected from the metal are bent into a circular arc of radius 20.0 cm by a magnetic field with a magnitude of 2.00 x 10^-5 T. What is the work function of the metal?

Answers

Photons of wavelength 450 nm are incident on a metal. The most energetic electrons ejected from the metal are bent into a circular arc of radius 20.0 cm by a magnetic field with a magnitude of 2.00 x 10^-5 T.The work function of the metal is approximately 2.45 x 10^-19 J.

To determine the work function of the metal, we can use the relationship between the energy of a photon and the work function of the metal.

The energy of a photon can be calculated using the equation:

E = hc/λ

Where:

E is the energy of the photon,

h is Planck's constant (approximately 6.626 x 10^-34 J·s),

c is the speed of light (approximately 3.00 x 10^8 m/s), and

λ is the wavelength of the photon.

Given that the wavelength of the incident photons is 450 nm (450 x 10^-9 m), we can calculate the energy of each photon.

E = (6.626 x 10^-34 J·s)(3.00 x 10^8 m/s) / (450 x 10^-9 m)

E = 4.42 x 10^-19 J

The energy of each photon is 4.42 x 10^-19 J.

Now, let's consider the electrons being bent into a circular arc by the magnetic field. The centripetal force on the electrons is provided by the magnetic force, given by the equation:

F = q×v×B

Where:

F is the magnetic force,

q is the charge of the electron (approximately -1.60 x 10^-19 C),

v is the velocity of the electrons, and

B is the magnitude of the magnetic field (2.00 x 10^-5 T).

The centripetal force is also given by the equation:

F = mv^2 / r

Where:

m is the mass of the electron (approximately 9.11 x 10^-31 kg), and

r is the radius of the circular arc (20.0 cm or 0.20 m).

Setting these two equations equal to each other and solving for v:

qvB = mv^2 / r

v = qBr / m

Substituting the known values:

v = (-1.60 x 10^-19 C)(2.00 x 10^-5 T)(0.20 m) / (9.11 x 10^-31 kg)

v ≈ -0.704 x 10^6 m/s

The velocity of the electrons is approximately -0.704 x 10^6 m/s.

Now, we can calculate the kinetic energy of the electrons using the equation:

KE = (1/2)mv^2

KE = (1/2)(9.11 x 10^-31 kg)(-0.704 x 10^6 m/s)^2

KE ≈ 2.45 x 10^-19 J

The kinetic energy of the electrons is approximately 2.45 x 10^-19 J.

The work function (Φ) is defined as the minimum energy required to remove an electron from the metal surface. Therefore, the work function is equal to the kinetic energy of the electrons.

Φ = 2.45 x 10^-19 J

Hence, the work function of the metal is approximately 2.45 x 10^-19 J.

To learn more about Photons visit: https://brainly.com/question/30130156

#SPJ11

Applications of Electrostatics The electric field one-fourth of the way from a charge 4: to another charge 92 is zero. What is the ratio of 1 to 4z?

Answers

The electric field is the area around electrically charged particles where the interaction between them creates an electric force. Electrostatics finds applications in a wide range of areas, including in the following fields:

In the industry, electrostatics is used to eliminate dirt and dust from plastic surfaces before painting them to achieve good adhesion. Aerospace engineering uses electrostatics in applications like the electrostatic cleaning of dust from the surface of spacecraft or the charging of space probes and dust detectors.

Medical technology relies on electrostatics in a range of applications, including in electrocardiography, electrophoresis, and in the use of electrostatic precipitators for respiratory protection.The electric field one-fourth of the way from a charge 4 to another charge 92 is zero.

What is the ratio of 1 to 4z?

The distance between charge 4 and charge 92 is 4z. Therefore, we can say that the electric field is zero at a distance of z from charge 4 (since z is 1/4th of the distance between 4 and 92).

Using Coulomb's law, we can calculate the electric field as:

E = (kQq)/r² Where k is the Coulomb constant, Q and q are the magnitudes of the charges, and r is the distance between them.

Since the electric field is zero at a distance of z from charge 4, we can write:

(k*4*Q)/(z²) = 0

Solving for Q, we get:

Q = 0

Therefore, the ratio of 1 to 4z is: 1/4z = 1/(4*z) = (1/4) * (1/z) = 0.25z^-1

Learn more about application of electrostatics here

https://brainly.in/question/17363791

#SPJ11

Consider an electric field perpendicular to a work bench. When a small charged object of mass 4.00 g and charge -19.5 μC is carefully placed in the field, the object is in static equilibrium. What are the magnitude and direction of the electric field? (Give the magnitude in N/C.) magnitude N/C direction

Answers

The magnitude of the electric field is 5.12 × 10^6 N/C, and it is directed upwards.

In order for the charged object to be in static equilibrium, the electric force acting on it must balance the gravitational force. The electric force experienced by the object can be calculated using the equation F = qE, where F is the force, q is the charge of the object, and E is the electric field.

Given that the mass of the object is 4.00 g (or 0.004 kg) and the charge is -19.5 μC (or -1.95 × [tex]10^{-8}[/tex] C), we can calculate the gravitational force acting on the object using the equation F_gravity = mg, where g is the acceleration due to gravity (approximately 9.8 [tex]m/s^2[/tex]).

Since the object is in equilibrium, the electric force and the gravitational force are equal in magnitude but opposite in direction. Therefore, we have F = F_gravity. Substituting the values, we get qE = mg, which can be rearranged to solve for the electric field E.

Plugging in the known values, we have (-1.95 × [tex]10^{-8}[/tex] C)E = (0.004 kg)(9.8 [tex]m/s^2[/tex]). Solving for E gives us E = (0.004 kg)(9.8 [tex]m/s^2[/tex])/(-1.95 × [tex]10^-8[/tex] C) ≈ 5.12 × [tex]10^6[/tex] N/C.

The negative charge on the object indicates that the direction of the electric field is directed upwards, opposite to the direction of the gravitational force.

Learn more about electric field here ;

https://brainly.com/question/30544719

#SPJ11

Question 5 (2 points) Listen Which of the following best describes the image produced by a flat mirror? real, inverted, and magnification less than one virtual, inverted, and magnification greater than one virtual, upright, and magnification equal to one real, upright, and magnification equal to one

Answers

The best description of the image produced by a flat mirror is: virtual, upright, and magnification equal to one. In the case of a flat mirror, the image formed is virtual, which means it cannot be projected onto a screen.

Instead, the image is formed by the apparent intersection of the reflected rays. This virtual image is always located behind the mirror, at the same distance as the object, and it cannot be physically captured or projected.

Furthermore, the image formed by a flat mirror is upright, meaning it has the same orientation as the object. If you raise your right hand in front of a flat mirror, the image in the mirror will also show a raised right hand. The mirror preserves the direction of the light rays, resulting in an upright image.

Lastly, the magnification of a flat mirror is equal to one. Magnification refers to the ratio of the height of the image to the height of the object. Since the image formed by a flat mirror is the same size as the object, the magnification is equal to one.

To summarize, a flat mirror produces a virtual, upright image with a magnification equal to one. It reflects the light rays without altering their orientation or size, allowing us to see ourselves and objects with a preserved reflection.

Learn more about mirror here:

https://brainly.com/question/3627454

#SPJ11

In the above figure you have five charges equally spaced from O. Therefore at the point O a. What is the net vertical electric field? (3) b. What is the net horizontal electric field? (4) c. What is the potential V?(4) d. If I place a 2C charge at O, what is the magnitude and the direction of the force it will experience? (2) e. What will be the potential energy of this 2C charge?

Answers

The potential energy of this 2C charge is equal to the work required to bring it from infinity to the point O. Since the potential at infinity is zero, the potential energy of the 2C charge at O is also zero.

a. The net vertical electric field at the point O is zero. There are two negative and two positive charges, with symmetrical arrangements, and so, the electric fields at O add up to zero.b.

The net horizontal electric field at the point O is zero. There are two negative and two positive charges, with symmetrical arrangements, and so, the electric fields at O add up to zero. c. The potential V at point O is zero. The potential at any point due to these charges is calculated by adding the potentials at that point due to each of the charges.

For symmetrical arrangements like the present one, the potential difference at O due to each charge is equal and opposite, and so, the potential difference due to the charges at O is zero. d. If a 2C charge is placed at O, it will experience a net force due to the charges on either side of O.

The magnitudes of these two forces will be equal and the direction of each of these forces will be towards the other charge. The two forces will add up to give a net force of magnitude F = kqQ/r^2, where k is the Coulomb constant, q is the charge at O, Q is the charge to either side of O, and r is the separation between the two charges.e.

The potential energy of this 2C charge is equal to the work required to bring it from infinity to the point O. Since the potential at infinity is zero, the potential energy of the 2C charge at O is also zero.

to know more about potential energy

https://brainly.com/question/16705765

#SPJ11

15.4 cm. Given this wavelength and frequency, what is the speed of the sound wave? 48.7 cm. Given this wavelength and frequency, what is the speed of the sound wave? speed of sound (in m/s ) under these conditions? Give your answer to the nearest 1 m/s.

Answers

Given this wavelength and frequency.  that the frequency of the first scenario is approximately 3.168 times the frequency of the second scenario.

To calculate the speed of a sound wave, we can use the formula: speed = wavelength × frequency.

For the first scenario with a wavelength of 15.4 cm, we need to convert it to meters by dividing it by 100: 15.4 cm = 0.154 m. Let's assume a frequency of f1. Using the formula, we have speed = 0.154 m × f1.

For the second scenario with a wavelength of 48.7 cm, we again convert it to meters: 48.7 cm = 0.487 m. Let's assume a frequency of f2. Using the formula, we have speed = 0.487 m × f2.

Since the speed of sound in air is generally considered constant (at approximately 343 m/s at room temperature and normal atmospheric conditions), we can equate the two expressions for speed and solve for f1 and f2

0.154 m × f1 = 0.487 m × f2

By canceling out the common factor of 0.154, we get:

f1 = 0.487 m × f2 / 0.154 m

Simplifying further:

f1 ≈ 3.168 × f2

This equation implies that the frequency of the first scenario is approximately 3.168 times the frequency of the second scenario. Therefore, to determine the speed of sound under these conditions, we need more information about either the frequency in one of the scenarios or the specific speed of sound for the given conditions.

Learn more about wave here:

https://brainly.com/question/25954805

#SPJ11

Consider the following system and its P controller transfer functions, G(s) and Ge(s) respectively: C(s) and G)-Kp=7 5s +1 r(t) e(t) u(t) y(t) Ge(s) G(s) 12.10.2011 10/201 y(t) Find the time constant after adding the controller Ges), for a unit step input. (Note: don't include units in your answer and calculate the answer to two decimal places for example 0.44)

Answers

The time constant of the closed-loop system is 1/35, which is approximately equal to 0.03

To find the time constant after adding the controller Ge(s) to the system, we need to determine the transfer function of the closed-loop system. The transfer function of the closed-loop system, T(s), is given by the product of the transfer function of the plant G(s) and the transfer function of the controller Ge(s):

T(s) = G(s) * Ge(s)

In this case, G(s) = 5s + 1 and Ge(s) = Kp = 7.

Substituting these values into the equation, we get:

T(s) = (5s + 1) * 7

= 35s + 7

To find the time constant of the closed-loop system, we need to determine the inverse Laplace transform of T(s).

Taking the inverse Laplace transform of 35s + 7, we obtain:

t(t) = 35 * δ'(t) + 7 * δ(t)

Here, δ(t) is the Dirac delta function, and δ'(t) is its derivative.

The time constant is defined as the reciprocal of the coefficient of the highest derivative term in the expression. In this case, the highest derivative term is δ'(t), and its coefficient is 35. Therefore, the closed-loop system's time constant is 1/35, which is nearly equivalent to 0.03. (rounded to two decimal places).


To know more about the Transfer functions, here

https://brainly.com/question/33247304

#SPJ4

An electrical circuit contains a capacitor of Z picofarads and a resistor of X ohms. If the x=1503 capacitor is fully charged, and then the voltage is interrupted, in how much time will about 95%Z=15.03 m of its charge be transferred to the resistor? Show your calculations.

Answers

The time taken to transfer about 95% of the charge to the resistor is 65.4 s (approx)

The given values in the problem are:X = 1503 ΩZ = 15.03 mF

The time taken to transfer about 95% of its charge to the resistor can be determined using the time constant (τ) of the circuit. The time constant (τ) of the circuit is given by the formula; τ = RC

where R is the resistance of the circuit in ohms and C is the capacitance of the circuit in farads.τ = RC = (1503 Ω)(15.03 × 10⁻³ F) = 22.56849 s ≈ 22.6 s (approx)

After one time constant, the charge on the capacitor is reduced to about 36.8% of its initial charge.

Hence, to transfer about 95% of its charge to the resistor, we need to wait for about 2.9 time constants (95 ÷ 36.8 ≈ 2.9).

The time taken to transfer about 95% of the charge to the resistor is;T = 2.9τ = 2.9 × 22.56849 s = 65.43861 s ≈ 65.4 s (approx)

Therefore, the time taken to transfer about 95% of the charge to the resistor is 65.4 s (approx)

Know more about resistor here,

https://brainly.com/question/30672175

#SPJ11

(a) How many minutes does it take a photon to travel from the Sun to the Earth? imin (b) What is the energy in eV of a photon with a wavelength of 513 nm ? eV (c) What is the wavelength (in m ) of a photon with an energy of 1.58eV ? m

Answers

(a) It takes approximately 8.3 minutes for a photon to travel from the Sun to the Earth.

(b) A photon with a wavelength of 513 nm has an energy of approximately 2.42 eV.

(c) A photon with an energy of 1.58 eV has a wavelength of approximately 7.83 × 10^-7 meters.

(a) Calculation of the time it takes a photon to travel from the Sun to the Earth:

The average distance from the Sun to the Earth is approximately 93 million miles or 150 million kilometers. Convert this distance to meters by multiplying it by 1,000, as there are 1,000 meters in a kilometer. So, the distance is 150,000,000,000 meters.

The speed of light in a vacuum is approximately 299,792 kilometers per second or 299,792,458 meters per second. To find the time it takes for a photon to travel from the Sun to the Earth, divide the distance by the speed of light:

Time = Distance / Speed of Light

Time = 150,000,000,000 meters / 299,792,458 meters per second

This gives  approximately 499.004 seconds. To convert this to minutes, we divide by 60:

Time in minutes = 499.004 seconds / 60 = 8.3167 minutes

Therefore, it takes approximately 8.3 minutes for a photon to travel from the Sun to the Earth.

(b) Calculation of the energy of a photon with a wavelength of 513 nm:

The energy of a photon can be calculated using the equation E = hc/λ, where E is the energy, h is Planck's constant, c is the speed of light, and λ is the wavelength of the photon.

Planck's constant (h) is approximately 4.1357 × 10^-15 eV·s.

The speed of light (c) is approximately 299,792,458 meters per second.

The given wavelength is 513 nm, which can be converted to meters by multiplying by 10^-9 since there are 1 billion nanometers in a meter. So, the wavelength is 513 × 10^-9 meters.

Substituting the values into the equation,

E = (4.1357 × 10^-15 eV·s × 299,792,458 m/s) / (513 × 10^-9 m)

Simplifying the equation, we get:

E = (1.2457 × 10^-6 eV·m) / (513 × 10^-9 m)

By dividing the numerator by the denominator,

E ≈ 2.42 eV

Therefore, a photon with a wavelength of 513 nm has an energy of approximately 2.42 eV.

(c) Calculation of the wavelength of a photon with an energy of 1.58 eV:

To find the wavelength of a photon given its energy, we rearrange the equation E = hc/λ to solve for λ.

We have the given energy as 1.58 eV.

Substituting the values into the equation,

1.58 eV = (4.1357 × 10^-15 eV·s × 299,792,458 m/s) / λ

To isolate λ, we rearrange the equation:

λ = (4.1357 × 10^-15 eV·s × 299,792,458 m/s) / 1.58 eV

By dividing the numerator by the denominator,

λ ≈ 7.83 × 10^-7 meters

Therefore, a photon with an energy of 1.58 eV has a wavelength of approximately 7.83 × 10^-7 meters or 783 nm.

These calculations assume that the photons are traveling in a vacuum.

Learn more about photon here:

https://brainly.com/question/33017722

#SPJ11

A Carnot refrigeration cycle is used to maintain a room at
23 °C by removing heat from groundwater at 15 °C.
Refrigerant R-134a enters the condenser as saturated
vapor at 40 °C and leaves as saturated liquid at the
same temperature. The evaporator pressure is 351 kPa.
a) If the room is to receive 2kW, what is power input to
the compressor?
b) Net power input to cycle?

Answers

a) The power input to the compressor in the Carnot refrigeration cycle, in order to supply 2 kW of cooling to the room, will depend on the efficiency of the cycle and the heat transfer involved.

b) The net power input to the cycle can be determined by considering the work done by the compressor and the work done on the system.

a) To calculate the power input to the compressor, we need to determine the heat transfer from the groundwater to the room. The Carnot refrigeration cycle is an idealized cycle, and its efficiency is given by the equation: Efficiency = 1 - (T_evaporator / T_condenser), where T_evaporator and T_condenser are the temperatures at the evaporator and condenser, respectively. Using this efficiency, we can calculate the heat transfer from the groundwater and convert it to power input.

b) The net power input to the cycle takes into account the work done by the compressor and the work done on the system. It can be calculated by subtracting the work done by the compressor from the heat transfer from the groundwater. The work done by the compressor can be determined using the power input calculated in part a), and the heat transfer from the groundwater can be obtained using the given temperatures and the specific heat properties of the refrigerant.

Overall, the Carnot refrigeration cycle involves several calculations to determine the power input to the compressor and the net power input to the cycle, considering the heat transfer and work done in the system.

To know more about the Carnot refrigeration cycle click here:

https://brainly.com/question/29234662

#SPJ11

A 6 pole induction motor has the ratings: U₁ = 400 V, n = 970 rpm, ƒ№ = 50 Hz, the stator windings are connected as Y, if the parameters are: r₁ = 2.08 №, r₂ = 1.53 N, x₁ = 3.12 №, x₂ = 4.25 N. Find out: (a) rated slip; (b) maximum torque; (c) overload ability Ami (d) the slip when the maximum torque occurs.

Answers

The maximum torque is 1082 Nm, which is achieved at 6.5% slip. The overload capacity is 227%. is the answer.

A 6-pole induction motor has the following specifications: U1 = 400 V, n = 970 rpm, f1 = 50 Hz, and the stator windings are connected in Y. Given the parameters r1 = 2.08 Ω, r2 = 1.53 Ω, x1 = 3.12 Ω, and x2 = 4.25 Ω, we are required to find out the following: rated slip maximum torque overload capacity

The formula for slip (s) is given by: s = (ns - nr) / ns where ns = synchronous speed

nr = rotor speed

Using the given values, we get: s = (ns - nr) / ns= (120 * f1 - nr) / (120 * f1)= (120 * 50 - 970) / (120 * 50)= 0.035 or 3.5%

This is the rated slip.

Maximum torque is achieved at the slip (s) that is 0.1 to 0.15 less than the rated slip (sr).

Hence, maximum torque slip (sm) can be calculated as follows: sm = sr - 0.1sr = rated slip sm = sr - 0.1= 0.035 - 0.1= -0.065or 6.5% (Approx)

The maximum torque is given by: T max = 3V12 / (2πf1) * (r2 / s) * [(s * (r2 / s) + x2) / ((r1 + r2 / s)2 + (x1 + x2)2) + s * (r2 / s) / ((r2 / s)2 + x2)2] where,V1 = 400 Vr1 = 2.08 Ωr2 = 1.53 Ωx1 = 3.12 Ωx2 = 4.25 Ωf1 = 50 Hz s = 0.035 (Rated Slip)

Putting all the values in the formula, we get: T max = 3 * 4002 / (2π * 50) * (1.53 / 0.035) * [(0.035 * (1.53 / 0.035) + 4.25) / ((2.08 + 1.53 / 0.035)2 + (3.12 + 4.25)2) + 0.035 * (1.53 / 0.035) / ((1.53 / 0.035)2 + 4.25)2]= 1082 Nm

Overload capacity is the percentage of the maximum torque that the motor can carry continuously.

This can be calculated using the following formula: Am = Tmax / Tn where T max = 1082 Nm

Tn = (2 * π * f1 * n) / 60 (Torque at rated speed)Putting all the values, we get: Am = Tmax / Tn= 1082 / [(2 * π * 50 * 970) / 60]= 2.27 or 227%

Therefore, the rated slip is 3.5%.

The maximum torque is 1082 Nm, which is achieved at 6.5% slip. The overload capacity is 227%.

know more about  maximum torque

https://brainly.com/question/30337233

#SPJ11

Determine the direction of the magnetic force in the following situations: (a) A negatively charged particle is moving north in a magnetic field which points up. (b) A positively charged particle is moving in the +x direction in a magnetic field that points in the −y direction. (c) A positively charged particle is stationary in a magnetic field that points in the +z direction. (d) A negatively charged particle is moving west in a magnetic field that points east. (e) A negatively charged particle is moving in the −z direction in a magnetic field that points in the −x direction. (f) A negatively charged particle is moving up in a magnetic field that points south.

Answers

The direction of the magnetic force can be determined using the right-hand rule for magnetic force.

According to this rule, if the thumb of the right hand points in the direction of the velocity of the charged particle, and the fingers point in the direction of the magnetic field, then the palm of the hand will indicate the direction of the magnetic force on the particle.

(a) For a negatively charged particle moving north in a magnetic field pointing up, the force would act to the west.(b) For a positively charged particle moving in the +x direction in a magnetic field pointing in the −y direction, the force would act in the +z direction.

(c) For a positively charged particle that is stationary in a magnetic field pointing in the +z direction, there would be no magnetic force since the particle is not in motion.(d) For a negatively charged particle moving west in a magnetic field pointing east, the force would act in the south direction.

(e) For a negatively charged particle moving in the −z direction in a magnetic field pointing in the −x direction, the force would act in the +y direction.(f) For a negatively charged particle moving up in a magnetic field pointing south, the force would act in the west direction.

Learn more about magnetic force here:

https://brainly.com/question/30532541

#SPJ11

Cubic equations of state have proven to be useful for a wide range of compounds and applications in thermodynamics. Explain why we are using cubic equation derived from P vs V data (graph) of liquid and vapor.

Answers

Cubic equations of state are highly beneficial for a wide range of thermodynamic applications because they use measurable quantities and provide critical data for predicting phase equilibrium in chemical engineering.

Cubic equations of state are highly useful for a wide range of compounds and applications in thermodynamics. A cubic equation derived from P vs V data (graph) of liquid and vapor is used for a variety of reasons, including: These equations make use of measurable quantities (pressure, temperature, and volume) and are extremely beneficial in the development of a thermodynamic framework for different compounds. These models may be used to estimate properties such as vapor pressures, fugacity coefficients, and liquid molar volumes, among others. The approach also allows for the calculation of the fugacity and molar volume of an ideal gas for a pure substance.

The data provided by these graphs are critical for predicting phase equilibrium in chemical engineering applications. They can also assist in the calculation of mixing and phase separation behavior for a variety of compounds. By using these equations, thermodynamic experts may evaluate the behavior of a substance and its properties under a variety of conditions, which is critical in the design and development of chemical processes. In conclusion, cubic equations of state are highly beneficial for a wide range of thermodynamic applications because they use measurable quantities and provide critical data for predicting phase equilibrium in chemical engineering.

To know more about equations visit:

https://brainly.com/question/28956380

#SPJ11

The sun's intensity at the distance of the earth is 1370 W/m² 30% of this energy is reflected by water and clouds; 70% is absorbed. What would be the earth's average temperature (in °C) if the earth had no atmosphere? The emissivity of the surface is very close to 1. (The actual average temperature of the earth, about 15 °C, is higher than your calculation because of the greenhouse effect.)

Answers

The question requires the calculation of the Earth's average temperature in °C if the earth had no atmosphere given the following information.

Sun's intensity at the distance of the earth is 1370 W/m².

30% of this energy is reflected by water and clouds;

70% is absorbed.

The emissivity of the surface is very close to 1. The actual average temperature of the earth, about 15 °C, is higher than the calculation because of the greenhouse effect.

Calculation of Earth's temperature:

The formula to determine the temperature is given by P = e σ A T⁴. Here,

P is the power received by the Earth from the Sun.

A is the surface area of the Earth,

T is the temperature in kelvin,

e is the emissivity of the surface,

σ is the Stefan-Boltzmann constant, and the remaining terms have the usual meanings.

Substituting the values in the formula,

P = (1 - 0.30) × 1370 W/m² × 4π (6,371 km)²

= 9.04 × 10¹⁴ Wσ

= 5.67 × 10⁻⁸ W/m² K⁴A

= 4π (6,371 km)²

= 5.10 × 10¹⁴ m²e = 1

Hence, the formula now becomes

9.04 × 10¹⁴ = 1 × 5.67 × 10⁻⁸ × 5.10 × 10¹⁴ × T⁴

⇒ T⁴ = 2.0019 × 10⁴

⇒ T = 231.02

K= -42.13°C

Answer: The Earth's average temperature would be -42.13°C.

Learn more about green house effect here

https://brainly.com/question/17023405

#SPJ11

A modern 1,200 MWe nuclear power station converts thermal energy to electricity via a steam cycle with an efficiency of 33%. Over the year it consumed 25 tonnes of enriched uranium although refuelling and maintenance meant the plant was not generating for a total of 8 weeks. Calculate the average fuel burnup rate in GWd/t.

Answers

The average fuel burnup rate in GWd/t is 6,984.

 

To calculate the average fuel burnup rate in GWd/t, we need to determine the total energy generated by the reactor over the year. The formula for calculating the total energy generated is:

Total energy generated = Annual energy generation / efficiency

Given that the annual energy generation is 1,200 GW and the efficiency is 0.33, we can calculate the total energy generated as follows:

Total energy generated = 1,200 GW x 8,760 hours / 0.33 = 31,891,891 MWh

Next, we need to calculate the mass of uranium consumed by the reactor over a year. The specific energy release for enriched uranium used in a typical modern reactor is approximately 7,000 kWh/kg. Using this value, we can calculate the mass of uranium consumed as follows:

Mass of uranium consumed = Total energy generated / Specific energy release

Mass of uranium consumed = 31,891,891 MWh x 10^6 / (7,000 kWh/kg x 10^3) = 4,560 tonnes

Therefore, the mass of uranium consumed by the reactor over the year is 4,560 tonnes.

The fuel burnup rate is defined as the amount of energy produced per unit mass of fuel consumed. We can calculate the fuel burnup rate as follows:

Fuel burnup rate = Total energy generated / Mass of uranium consumed

Fuel burnup rate = 31,891,891 MWh x 10^6 / (4,560 tonnes x 10^3)

Fuel burnup rate = 6,984 GWd/t

Therefore, the average fuel burnup rate in GWd/t is 6,984.

Learn more about fuel

https://brainly.com/question/33339410

#SPJ11

Three long, parallel wires carry equal currents of I=4.00 A. In a top view, the wires are located at the corners of a square with all currents flowing upward, as shown in the diagram. Determine the magnitude and direction of the magnetic field at a. the empty corner. b. the centre of the square.

Answers

(a) The magnitude of the magnetic field at the empty corner is 3π x 10⁻⁷/d, T.

(b) The magnitude of the magnetic field at the center of the square is 0.

What is the magnitude of the magnetic field?

(a) The magnitude of the magnetic field at the empty corner is calculated as;

B = μ₀I/2πd

where;

μ₀ is permeability of free spaceI is the currentd is the distance of the wires

The resultant magnetic field at the empty corner will be the vector sum of the three wire fields:

B_net =  3B

B_net = 3(4π × 10⁻⁷ × 4 / d)

B_net = 3π x 10⁻⁷/d, T

(b) The magnitude of the magnetic field at the center of the square is calculated as;

each magnetic field in opposite direction will cancel out;

B(net) = 0

Learn more about magnetic field here: https://brainly.com/question/7802337

#SPJ4

Light is incident on two slits separated by 0.20 mm. The observing screen is placed 3.0 m from the slits. If the position of the first order bright fringe is at 4.0 mm above the center line, find the wavelength of the light, in nm.
Find the position of the third order bright fringe, in degrees.
Shine red light of wavelength 700.0 nm through a single slit. The light creates a central diffraction peak 6.00 cm wide on a screen 2.40 m away. To what angle do the first order dark fringes correspond, in degrees?
What is the slit width, in m?
What would be the width of the central diffraction peak if violet light of wavelength 440.0 nm is used instead, in cm?

Answers

The wavelength of the light is 267 nm, the position of the third order bright fringe is approximately 0.76 degrees, the angle of the first order dark fringe for red light is approximately 0.333 degrees, the slit width is approximately 0.060 m and the width of the central diffraction peak for violet light is approximately 3.8 cm.

To find the wavelength of light, we can use the formula for the position of the bright fringe in a double-slit interference pattern:

y = (m * λ * L) / d

where:

y is the distance of the bright fringe from the center line,

m is the order of the bright fringe (1 for the first order),

λ is the wavelength of light,

L is the distance from the slits to the observing screen,

d is the separation between the two slits.

Given that y = 4.0 mm = 0.004 m, m = 1, L = 3.0 m, and d = 0.20 mm = 0.0002 m, we can solve for λ:

0.004 = (1 * λ * 3.0) / 0.0002

λ = (0.004 * 0.0002) / 3.0 = 2.67 × 1[tex]10^{-7}[/tex] m = 267 nm

Therefore, the wavelength of the light is 267 nm.

To find the position of the third order bright fringe, we can use the same formula with m = 3:

y = (3 * λ * L) / d

Substituting the given values, we have:

y = (3 * 267 * [tex]10^{-9}[/tex] * 3.0) / 0.0002 = 0.040 m

To convert this to degrees, we can use the formula:

θ = arctan(y / L)

θ = arctan(0.040 / 3.0) ≈ 0.76 degrees

Therefore, the position of the third order bright fringe is approximately 0.76 degrees.

For the single-slit diffraction pattern, the formula for the angle of the dark fringe can be expressed as:

θ = λ / (2 * w)

where:

θ is the angle of the dark fringe,

λ is the wavelength of light,

w is the slit width.

Given that λ = 700.0 nm = 7.00 × [tex]10^{-7}[/tex] m and the central diffraction peak width is 6.00 cm = 0.06 m, we can solve for θ:

θ = (7.00 × [tex]10^{-7}[/tex]) / (2 * 0.06) ≈ 0.0058 radians

To convert this to degrees, we multiply by 180/π:

θ ≈ 0.0058 * (180/π) ≈ 0.333 degrees

Therefore, the angle of the first order dark fringe for red light is approximately 0.333 degrees.

To find the slit width w, we rearrange the formula:

w = λ / (2 * θ)

Substituting the given values, we have:

w = (7.00 × [tex]10^{-7}[/tex]) / (2 * 0.0058) ≈ 0.060 m

Therefore, the slit width is approximately 0.060 m.

Finally, to find the width of the central diffraction peak for violet light of wavelength 440.0 nm = 4.40 × [tex]10^{-7}[/tex] m, we can use the same formula:

w = λ / (2 * θ)

Substituting λ = 4.40 × [tex]10^{-7}[/tex] m and θ = 0.0058 radians, we have:

w = (4.40 × [tex]10^{-7}[/tex]) / (2 * 0.0058) ≈ 0.038 m = 3.8 cm

Therefore, the width of the central diffraction peak for violet light is approximately 3.8 cm.

Learn more about diffraction here:

https://brainly.com/question/12290582

#SPJ11

A billiard cue ball with a mass of 0.60 kg and an eight ball with a mass of 0.55 kg are rolled toward each other. The cue ball has a velocity of 3.0 m/s heading east and the eight ball has a velocity of 2.0 m/s heading north. After the collision, the cue ball moves off at a velocity of 2.0 m/s 40⁰ north of east.
What is net momentum of the system above before and after the collision?
What north component (y-component) of the momentum of the cue ball after collision?
Using your responses above, determine the final velocity of the eight ball:

Answers

The net momentum of the system before the collision is given by the expression: Momentum before = m1v1 + m2v2where m1 and v1 are the mass and velocity of the cue ball respectively and m2 and v2 are the mass and velocity of the eight ball respectively.

Substituting in the given values, we have:Momentum before = (0.6 kg) (3.0 m/s) + (0.55 kg) (2.0 m/s) = 1.80 kg m/s + 1.10 kg m/s = 2.90 kg m/s. The net momentum of the system after the collision is given by the expression:Momentum after = m1v1' + m2v2'where v1' and v2' are the velocities of the cue ball and eight ball respectively after the collision.

Substituting in the given values, we have: Momentum after = (0.6 kg) (2.0 m/s cos 40°) + (0.55 kg) (v2')Momentum after = 1.20 cos 40° kg m/s + (0.55 kg) (v2')Momentum after = 0.92 kg m/s + 0.55 kg v2'Conservation of momentum principle states that the total momentum before the collision must equal the total momentum after the collision: Momentum before = Momentum after2.90 kg m/s = 0.92 kg m/s + 0.55 kg v2'Solving for v2', we get:v2' = (2.90 kg m/s - 0.92 kg m/s) / 0.55 kgv2' = 4.71 m/s.

The north component (y-component) of the momentum of the cue ball after collision is given by the expression:py = m1v1' sin θSubstituting the given values, we have:py = (0.6 kg) (2.0 m/s sin 40°)py = 0.78 kg m/sTherefore, the final velocity of the eight ball is 4.71 m/s.

Learn more on momentum here:

brainly.in/question/7381860

#SPJ11

Other Questions
The force on a particle is directed along an x axis and given by F= F(x/x - 1) where x is in meters and F is in Newtons. If F = 2.2 N and x = 5.9 m, find the work done by the force in moving the particle from x = 0 to x = 2x m. Number ______________ Units ________________A 80 kg block is pulled at a constant speed of 3.8 m/s across a horizontal floor by an applied force of 120 N directed 43 above the horizontal. What is the rate at which the force does work on the block? Number ______________ Units ________________ What is the % dissociation of an acid, HA 0.10 M, ifthe solution has a pH = 3.50? a) 0.0032 b) 35 C) 0.32 d) 5.0 e) 2.9 A capacitor is connected to an AC source. If the maximum current in the circuit is 0.400 A and the voltage from the AC source is given by Av = (82.2 V) sin((601)s-lt], determine the following. (a) the rms voltage (in V) of the source V (b) the frequency (in Hz) of the source Hz (c) the capacitance (in pF) of the capacitor uf Last week, Linda went to a pet supply boutique to look at a carrier for her cat. She was surprised to find the carrier priced $50 higher than she could order it for direct from the manufacturer online. The boutique owner said that she was discontinuing the items. This is an example of:Select one:A.price elasticityB.price conflictC.logistics expenseD.channel conflict Comparing to regular illuminating light bulbs, all lasers have following characteristics except A. Higher brightness. B. Higher output power. C. Longer coherence length. D. Smaller beam divergent angle. We are making a simple calculator that performs addition, subtraction, multiplication, division, exponential operation, and radical operation based on the user inputs.Ask the user what operation he/she wantsBased on the selected operation, ask the user the operands.Then perform the operation and display the resultThen ask the user if he/she wants to continue, if yes, continue to step 1; if not, exit the program. According to myth, what is one reason the grandmother spider worries aboutraising the sun's child?OA. Because she is herself starvingOB. Because his father is dangerousOC. Because he is humanOD. Because he is a boyIts not C Walter Payton played for the Chicago Bears for 13 seasons.A) QuotableB) FactC) Personal ExperienceD) Not EvidenceWalter Payton's 8 touchdown passes are an NFL record for non-quarterbacks.A) Expert TestimonyB) Personal ExperienceC) StatisticalD) QuotableFact - include names, dates, or specific events.Statistical - facts expressed in numbersExpert Testimony - Experts in the field about which you are writing provide supporting details and evidence for your thesis statement.Quotable - quotable comments provide support for your statement or argument.Personal Experience - descriptive details and impressions. You are provided some data about the market: The expected return of the market portfolio is 11.19%, the market's volatility is 20.3%, and the risk-free rate is 1.3%. If the beta of ROKU is 1.11, according to the CAPM, what is the expected return of ROKU? Determine wether. or not each of the following signals is periodic. a) X (t) = 2e (t+1/4) ULE) ? b) x [n] = u[n]+u[n] c) X [n] = (2) u [n-3] d) X (t) = e(1+5)= e) X5 [n] = 3e j (n + /2) Use the Laplace transform to find the solution of the differential equation y"(t) + 4(t) + 3y(t) = x(t), y(0) = 2, y'(0) = 2. The signal x(t) is given by: 1, t < 3 x(t) = = t t - 3, 3 t 6. 3, t> 6 3. (25 p). Use the Laplace transform to find the solution of the differential equation y'"(t) + y'(t) 2y(t) = 8(t), y(0) = 4, y' (0) = 2, y" (0) = 3. 4. (25 p). Consider a different system function, 4 1 H(s) = Re(s) > s2 + s + 16.25' Find and plot the poles of this system function using pzplot function of MATLAB. 1. Define Grahams law of diffusion of gases.2. What is the hypothesis of Avogadro?3. Give a mathematical equation for Daltons law.4. Define Gay-Lussacs law for volume. As the Public sector Public Sector Public RelationsExecutive, You have been asked by Management to a Norwegian groupwho cannot meet you personally because of COVID 19 protocolsAnswer this Question (Noraannual compounding using a calculator) Roninie Rental plans to invest $2,100 at the end of each 6 -month for 5 years into an account biat pays 7.1 percent corepounded semiannually. He will use this money as a down payment on a new home at the end of the 5 years How large will his down payment be 5 years from today? After 5 years. Ronnie will have (Round to the nearest cent) Sheridan Corporation issued 2,600, 7%, 5-year, $1,000 bonds dated January 1, 2022, at 100. Interest is paid each January 1. (a) Prepare the journal entry to record the sale of these bonds on January 1, 2022. (Credit account titles are automatically indented when amount is entered. Do not indent manually) Date Account Titles and Explanation Debit Credit Janaury 1, 2022 (b) Prepare the adjusting journal entry on December 31, 2022, to record interest expense. (Credit account titles are automatically indented when amount is entered. Do not indent manually.) Date Account Titles and Explanation Debit Credit December I 31, 2022 (c) Prepare the journal entry on January 1, 2023, to record interest paid. (Credit account titles are automatically indented when amount is entered. Do not indent manually.) Date Account Titles and Explanation Debit Credit January 1.2023 Write a couple of paragraphs about a potential earthquake, tsunami or volcano that may cause a future disaster for the United States. Use online sources to justify your selection. Where is the event likely to occur in the United States? What is potential size and cost of such an event? How likely is this event in your lifetime? Explain osmosis in plant and animal cells Verify the truth of the Max-Flow/Min-Cut Theorem for the network flow which you found in (a). Start by finding all the feasible (r, s)-cuts. What would be the maximum flow if the direction of the arrow from a to c were reversed? (Use the Max-Flow Min-Cut Theorem to determine this.) How could a SAYGO tax system help support intergenerational wellbeing?. Please use economic analysis Subject: Visual Programming (Visual Basic/VB)1. What is a syntactic error? When do syntactic errors occur? What happen when a syntactic error is detected?2. What is a logical error? When are logical errors detected? How do logical errors differ from syntactic error?3. What is the difference between a sub procedure and function procedure?4. How are sub procedures named? Does a sub procedure name represent a data item?5. What is the purpose of arguments? Are arguments required in every procedure?6. What is meant by passing an argument by reference?7. What is meant by passing an argument by value?