a) The rms values of load and primary current are approximately 0.314 A and 0.081 A, respectively. b) VL(ac) is approximately 5.966 V. c) V(ac) at the transformer primary is approximately 23.08 V. d) P(ac) across the transformer primary is approximately 1.87 W. e) The efficiency of the circuit, considering a bias current of 150 mA, is approximately 68.6%.
a) The rms values of load and primary current.
To calculate the rms values of load and primary current, we need to use the power equation:
P = I^2 * R
where P is the power, I is the current, and R is the resistance.
Given that the power delivered to the load is 2 W and the load impedance is 16-22 Ω, we can use the average value of the impedance (19 Ω) for calculation purposes.
For the load current:
P = I_load^2 * R_load
2 = I_load^2 * 19
I_load^2 = 2/19
I_load = sqrt(2/19)
I_load ≈ 0.314 A
For the primary current, we need to consider the turns ratio of the transformer. The turns ratio is given as 3.87:1, which means the primary current will be scaled down by the same ratio.
I_primary = I_load / turns ratio
I_primary = 0.314 A / 3.87
I_primary ≈ 0.081 A
b) VL(ac)
To calculate VL(ac), we can use Ohm's law:
VL(ac) = I_load * R_load
VL(ac) = 0.314 A * 19 Ω
VL(ac) ≈ 5.966 V
c) V(ac) at transformer primary.
V(ac) at the transformer primary is calculated using the turns ratio:
V(ac)_primary = V(ac)_load * turns ratio
V(ac)_primary = 5.966 V * 3.87
V(ac)_primary ≈ 23.08 V
d) P(ac) across transformer primary.
To calculate P(ac) across the transformer primary, we can use the power equation:
P(ac)_primary = V(ac)_primary * I_primary
P(ac)_primary ≈ 23.08 V * 0.081 A
P(ac)_primary ≈ 1.87 W
e) Calculate the efficiency of the circuit if the bias current is Ico = 150 mA.
The efficiency of the circuit is given by the ratio of output power to input power.
Efficiency = P(out) / P(in) * 100%
The bias current does not affect the efficiency directly, so we can ignore it in this calculation.
P(in) = Vcc * I_primary
P(in) = 36 V * 0.081 A
P(in) ≈ 2.916 W
Efficiency = 2 W / 2.916 W * 100%
Efficiency ≈ 68.6%
To know more about Transformer, visit
https://brainly.com/question/24249197
#SPJ11
Draw the single slop ADC b. explain its operation c. state its disadvantages.
Single Slope ADC is the simplest kind of Analog to Digital Converter. It works by charging a capacitor for a known period of time and then discharging the same capacitor into a counter.
The number of clock cycles needed to completely discharge the capacitor is counted. It is a type of integrator type ADC.A circuit diagram of Single Slope ADC,The operation of Single Slope ADC is as follows:In the starting of conversion, the switch is closed for a short time.
During this period, the capacitor is charged by the input analog signal.The switch is then opened and capacitor starts discharging at a linear rate. The rate of discharge of the capacitor is constant and is equal to the rate of clock pulses applied to the counter.The output of the counter is then transferred to a digital display.
To know more about Analog visit:
https://brainly.com/question/576869
#SPJ11
Let X1=[1,0,2,-1] , X2=[-1,1,0,1] , and X3=[2,0,0,-2] and let W=
Span{X1, X2 , X3}.
Find an orthonormal basis for W.
Answer:
To find an orthonormal basis for W = Span{X1, X2, X3}, we can use the Gram-Schmidt process. This involves taking the first vector and normalizing it to obtain the first basis vector, and then subtracting the projection of the second vector onto the first basis vector from the second vector to obtain the second basis vector, and so on.
First, we normalize the first vector X1:
v1 = X1 / ||X1|| = [1/3, 0, 2/3, -1/3]
where ||X1|| is the norm of X1.
Next, we compute the projection of X2 onto v1, and subtract it from X2:
proj_v1(X2) = (X2 · v1) * v1 = [(2/3) / (1/3)] * v1 = [2, 0, 4/3, -2/3]
v2 = X2 - proj_v1(X2) = [-5/3, 1, -4/3, 4/3]
where · denotes the dot product.
Then, we compute the projection of X3 onto v1 and v2, and subtract these from X3:
proj_v1(X3) = (X3 · v1) * v1 = [(2/3) / (1/3)] * v1 = [2, 0, 4/3, -2/3]
proj_v2(X3) = (X3 · v2) * v2 = [-1/3, 2/3, -1/3, 1/3]
v3 = X3 - proj_v1(X3) - proj_v2(X3) = [-1/3, -2/3, 2/3, -1/3]
Finally, we normalize v2 and v3 to obtain the orthonormal basis vectors:
u2 = v2 / ||v2|| = [-sqrt(5)/5, sqrt(5)/5, -2/sqrt(5), 2/sqrt(5)]
u3 = v3 / ||v3|| = [-1/3sqrt(2), -2/3sqrt(2), sqrt(2)/3, -1/3sqrt(2)]
Therefore, an orthonormal basis for W = Span{X
Explanation:
A discrete LTI system is characterised by the following Transfer Function: H(z) = 1 + z-1 a) Find the Impulse Response of the system stating its Region of Convergence. b) Sketch the pole-zero representation of the system in the 2-plane, paying particular attention to the Region of Convergence obtained in part a) above. c) Find the Magnitude Response of the system and plot it against the angular frequency. Comment on the periodicity of the obtained spectrum. d) Find the Phase Response of the system and determine its value for w="rad/s.
We must perform the inverse Z-transform of the transfer function H(z) in order to get the system's impulse response. [tex]H(z) = 1 + z^{(-1)[/tex] can be used to rewrite the transfer function provided as H(z) = 1 + z(-1).
We obtain h[n] = δ[n] + δ[n-1], by taking the inverse Z-transform of H(z), where δ[n] is the discrete-time impulse function. Two unit impulses at n = 0 and n = 1 make up the impulse response.
The entire z-plane other than z = 0 is the region of convergence (ROC) for this system.
The transfer function H(z) = (z + 1)/z can be factored to produce the system's pole-zero representation. There is a pole at z = 0, and the zero is at z = -1.
When drawing the pole-zero diagram, we show the pole at z = 0 as a small circle and the zero at z = -1 as a circle with a cross within. The area outside the unit circle centred at the origin is where the ROC obtained in section a) is located.
The magnitude response of the system can be obtained by substituting z = e^(jω) into the transfer function H(z) and evaluating its magnitude. H(z) = 1 + e^(-jω).
The magnitude response |H(ω)| can be calculated as |H(ω)| = sqrt(1 + cos(ω))^2 + sin(ω)^2 = sqrt(2 + 2cos(ω)).
The phase response of the system can be obtained by evaluating the argument of H(z) at z = e^(jω). The phase response ϕ(ω) = arg(H(ω)) can be calculated as ϕ(ω) = arctan(sin(ω)/(1 + cos(ω))).
Thus, to determine the phase response at a specific value of ω, substitute the value into the phase response equation.
For more details regarding Transfer Function, visit:
https://brainly.com/question/28881525
#SPJ4
Verrazano bridge has four suspension cables of 36 inches in diameter each.
Compute the number of Verrazano suspension cable equivalents needed for the DC transmission.
The given information is as follows:Verrazano bridge has four suspension cables of 36 inches in diameter each.Formula used to calculate the number of suspension cables are given below:Equivalent number of conductors= Current capacity (in Amperes) × Length (in miles) / (Voltage (in kilovolts) × Power factor × √3 × Conductivity (in mho/ohm))Where;Current capacity is the maximum current that a conductor can carry safely under normal operating conditions.Power factor refers to the ratio of actual power to apparent power.
Conductivity refers to the ability of a material to conduct electricity. Voltage is the electrical potential difference, which is measured in volts.√3 is the square root of three.
Let's calculate the equivalent number of conductors: Equivalent number of conductors= 3435 A × 2500 mi / (1000 kV × 0.95 × √3 × 234 × 10-7 mho/ohm)Equivalent number of conductors = 38.4 conductorsTherefore, 38 suspension cable equivalents needed for the DC transmission.
To know more about Verrazano bridge here"
brainly.com/question/5031615
#SPJ11
A chemical reactor process has the following transfer function, G₁ (s) = (3s +1)(4s +1) P . Internal Model Control (IMC) scheme is to be applied to achieve set-point tracking and disturbance rejection. a) Draw a block diagram to show the configuration of the IMC control system, The
In order to achieve set-point tracking and disturbance rejection, we will apply Internal Model Control (IMC) scheme to the chemical reactor process that has the following transfer function G₁ (s) = (3s + 1)(4s + 1) P. We are asked to draw a block diagram showing the configuration of the IMC control system.
We can solve this problem as follows:
Solution:
Block diagram of Internal Model Control (IMC) scheme for the given chemical reactor process:
Explanation:
From the given information, we have the transfer function of the process as G₁ (s) = (3s + 1)(4s + 1) P. The IMC controller is given by the transfer function, CIMC(s) = 1/G₁(s) = 1/[(3s + 1)(4s + 1) P].
The block diagram of the IMC control system is shown above. It consists of two blocks: the process block and the IMC controller block.
The set-point (SP) is the desired output that we want the system to achieve. It is compared with the output of the process (Y) to generate the error signal (E).
The error signal (E) is then fed to the IMC controller block. The IMC controller consists of two parts: the proportional controller (Kp) and the filter (F). The proportional controller (Kp) scales the error signal (E) and sends it to the filter (F).
The filter (F) is designed to mimic the process dynamics and is given by the transfer function, F(s) = (3s + 1)(4s + 1). The output of the filter is fed back to the proportional controller (Kp) and subtracted from the output of the proportional controller (KpE). This gives the control signal (U) which is then fed to the process block.
The process block consists of the process (G) and the disturbance (D). The disturbance (D) is any external factor that affects the process output (Y) and is added to the process output (Y) to give the plant output (Y+D).
The plant output (Y+D) is then fed back to the IMC controller block. The plant output (Y+D) is also the output of the overall control system.
Know more about Internal Model Control here:
https://brainly.com/question/13770859
#SPJ11
How many transistors are used in a 4-input CMOS AND gate? How many of each type are used? Draw the circuit diagram.
A 4-input CMOS AND gate typically uses 28 transistors: 14 PMOS (p-channel metal-oxide-semiconductor) transistors and 14 NMOS (n-channel metal-oxide-semiconductor) transistors.
A CMOS AND gate consists of a network of transistors that implement the logical AND operation. In a 4-input CMOS AND gate, the inputs are connected to the gates of the NMOS transistors, and their complements (inverted inputs) are connected to the gates of the PMOS transistors. The drain terminals of the NMOS transistors are connected to the output, and the source terminals of the PMOS transistors are also connected to the output.
For each input, you need one PMOS and one NMOS transistor. Therefore, for a 4-input CMOS AND gate, you will need a total of 4 PMOS and 4 NMOS transistors. Additionally, you need two pull-up PMOS transistors and two pull-down NMOS transistors to ensure proper logic levels at the output. So, in total, you will need 4 + 4 + 2 + 2 = 12 transistors.
However, CMOS gates are typically implemented as complementary pairs to achieve symmetrical rise and fall times. Therefore, the number of transistors is doubled. Hence, a 4-input CMOS AND gate uses 2 * 12 = 24 transistors.
A 4-input CMOS AND gate uses a total of 24 transistors: 12 PMOS transistors and 12 NMOS transistors
To know more about transistors visit :
https://brainly.com/question/31675242
#SPJ11
Consider the differential equation: y(t)+2y(t)=u(t) a. If u(t) is constant then y(t)≈0 when time goes to infinity. What value will y(t) approach as t→[infinity] if u(t)=5?(11pts) b. Determine the transfer function relating Y(s) and Y(s) for the differential equation above. (10 pts)
a. In order to solve the differential equation, we need to find its homogeneous and particular solutions. The homogeneous solution is given by y_h(t) = C*e^(-2t), where C is a constant. The particular solution is given by y_p(t) = K, where K is a constant, since u(t) is a constant.
Substituting y_p(t) and u(t) into the differential equation, we get:
K + 2K = 5
Solving for K, we get K = 5/3.
Therefore, the general solution of the differential equation is:
y(t) = y_h(t) + y_p(t) = C*e^(-2t) + 5/3
As t goes to infinity, the term C*e^(-2t) approaches zero, since e^(-2t) approaches zero much faster than t approaches infinity. Therefore, y(t) approaches 5/3 as t goes to infinity, when u(t) is constant and equal to 5.
b. Taking the Laplace transform of the differential equation, and solving for Y(s)/U(s), we get:
Y(s)/U(s) = 1/(s+2)
Therefore, the transfer function relating Y(s) and U(s) is:
H(s) = Y(s)/U(s) = 1/(s+2)
In conclusion, for a constant value of u(t) equal to 5, y(t) approaches 5/3 as t goes to infinity for the given differential equation. The transfer function relating Y(s) and U(s) is H(s) = 1/(s+2).
To know more about differential equation, visit:
https://brainly.com/question/1164377
#SPJ11
A given 6-dB directional coupler has a specified directivity of 20-dB. How much power is delivered to the coupled port if the input power is 20 mW and all ports are matched? Enter your answer in mW without including the unit.
The power delivered to the coupled port is approximately 19.8 mW.
To determine the power delivered to the coupled port of a directional coupler, we can use the directivity and input power values. Directivity is defined as the ratio of the power coupled to the output port compared to the power coupled to the coupled port.
Given:
Input power (Pᵢ) = 20 mWDirectivity (D) = 20 dB = 10^(20/10) = 100The power delivered to the coupled port (P_c) can be calculated using the formula:
P_c = (D / (D + 1)) * Pᵢ
Substituting the values:
P_c = (100 / (100 + 1)) * 20 mW
Simplifying the equation:
P_c = (100 / 101) * 20 mW
Calculating:
P_c ≈ 19.8 mW
Therefore, approximately 19.8 mW of power is delivered to the coupled port
To learn more about power, Visit:
https://brainly.com/question/11569624
#SPJ11
Select the asymptotic worst-case time complexity of the following algorithm:
Algorithm Input: a1, a2, ..., an,a sequence of numbers n,the length of the sequence y, a number
Output: ?? For k = 1 to n-1 For j = k+1 to n If (|ak - aj| > 0) Return( "True" ) End-for End-for Return( "False" )
a. Θ(1)
b. Θ(n)
c. Θ(n^2)
d. Θ(n^3)
The correct answer is c. Θ[tex](n^2)[/tex]. The algorithm has a time complexity of Θ[tex](n^2)[/tex] because the number of iterations is proportional to [tex]n^2[/tex].
Select the asymptotic worst-case time complexity of the algorithm: "For k = 1 to n-1, For j = k+1 to n, If (|ak - aj| > 0), Return("True"), End-for, End-for, Return("False")" a. Θ(1), b. Θ(n), c. Θ(n^2), d. Θ(n^3)?The given algorithm has two nested loops: an outer loop from k = 1 to n-1, and an inner loop from j = k+1 to n. The inner loop performs a constant-time operation |ak - aj| > 0.
The worst-case time complexity of the algorithm can be determined by considering the maximum number of iterations the loops can perform. In the worst case, both loops will run their maximum number of iterations.
The outer loop iterates n-1 times (from k = 1 to n-1), and the inner loop iterates n-k times (from j = k+1 to n). Therefore, the total number of iterations is given by the sum of these two loops:
(n-1) + (n-2) + (n-3) + ... + 2 + 1 = n(n-1)/2
This means that the algorithm's running time grows quadratically with the size of the input.
The correct answer is c. Θ[tex](n^2)[/tex].
Learn more about proportional
brainly.com/question/32890782
#SPJ11
for full wave equations. 1² (i) What is meant by the term optimum number of stages as applied in Cascaded Voltage Multiplier Circuit? [2 marks] SECTION B (40 marks) ANY FOUR (AY quoptions Ioach question
A cascaded voltage multiplier circuit is an electrical circuit used to multiply the voltage of an input signal. It contains a series of diodes and capacitors connected in a ladder-like arrangement. The term "optimum number of stages" refers to the number of stages in the voltage multiplier circuit that results in the highest output voltage with the least amount of distortion and loss in power.
An ideal voltage multiplier circuit would produce a high output voltage with minimal distortion and power loss. However, in practice, every stage of the voltage multiplier circuit introduces some level of distortion and power loss. Therefore, the optimum number of stages for a given circuit is the number of stages that maximizes the output voltage while minimizing the distortion and power loss.
In general, the optimum number of stages will depend on the specific parameters of the voltage multiplier circuit, such as the capacitance and resistance values of the components used. In most cases, the optimum number of stages is determined through a trial-and-error process or through simulation using circuit analysis software.
know more about cascaded voltage
https://brainly.com/question/30830876
#SPJ11
MATLAB: Mechanical Systems Assuming the harmonic force F(t)=Asin(wt) is the disturbance applied to the mass M, derive the equations of motion of the system. F(t) M Script M b B y(t) Store your answer in mxdot and Mydot 1 format compact 2 % for symbolic declaration K x(t) y(t) A B wt 3 Save C Reset My Solutions > Dy = 8 Ft = 9 Fs = 10 Fd = 11 % Use equations Fs, Fd, and to rewrite the equation in terms of the linear model for a spring and viscous damper. 12 mxdot= 13 Mydot= MATLAB Documentation 4 % Use Newton's law of motion, concepts of action and reaction, and friction to derive the equation of motion from the free body diagram for the ma 5 % Use the free body diagram to write the equation of motion for the top mass, m, in terms of m, x, fs, and fd. 6 Dx =
The problem asks to derive the equations of motion for the given mechanical system under the influence of the harmonic force F(t) = Asin(wt) acting on the mass M. We need to derive the equation of motion for this system Thus, option (b) is the correct answer.
We will use Newton's law of motion to derive the equation of motion for mass M and the free-body diagram to write the equation of motion for the top mass m in terms of m, x, fs, and fd. The symbolic declaration for MATLAB is as follows:
1 format compact 2 % for symbolic declaration K x(t) y(t) A B wt 3 Save C Reset My Solutions > Dy = 8 Ft = 9 Fs = 10 Fd = 11 % Equations Fs, Fd, and 8 can be used to rewrite the equation in terms of the linear model for a spring and viscous damper.
12 mxdot= 13 Mydot= MATLAB Documentation Applying Newton's law of motion for the mass M, we get: Fnet = ma ... (1)where, Fnet = F(t) - b(v-Mv1) - k1(x-Mx1) - k2(y-x) ... (2)
(3)where Fnet = fs - fd... (4) Using equations (3) and (4), we get: fs - fd = ma... (5)
Therefore, the equations of motion for the given mechanical system are as follows:mxdot = x1 ... (6)Mydot = (1/M)*(Asin(wt) - b(v-Mv1) - k1(x-Mx1) - k2(y-x)) ... (7)
where v is the velocity of mass M, and x1 and v1 are the initial positions and velocities of masses m and M, respectively. Thus, option (b) is the correct answer.
To learn more about motion, visit:
https://brainly.com/question/2748259
#SPJ11
could uou please answer
7. What happens to Vcand V. in a series RC circuit when the frequency is increased?
When the frequency is increased in a series RC circuit, the voltage across the capacitor (Vc) decreases, while the voltage across the resistor (Vr) increases.
In a series RC circuit, the impedance (Z) is given by the equation Z = R + 1/(jωC), where R is the resistance, C is the capacitance, ω is the angular frequency (2πf), and j is the imaginary unit.
As the frequency increases, the angular frequency ω increases as well. Since the impedance of the capacitor is inversely proportional to the frequency (Zc = 1/(jωC)), the impedance of the capacitor decreases as the frequency increases.
According to Ohm's law, V = IZ, where V is the voltage and I is the current. In a series circuit, the current is the same throughout. Therefore, as the impedance of the capacitor decreases, more voltage drops across the resistor (Vr) compared to the capacitor (Vc).
In summary, when the frequency is increased in a series RC circuit, the voltage across the capacitor decreases, and the voltage across the resistor increases due to the changing impedance of the capacitor with frequency.
To know more about Capacitor, visit : brainly.com/question/31627158
#SPJ11
A single face transistorized bridge inverter has a resistive load off 3 ohms and the DC input voltage of 37 Volt. Determine
a) transistor ratings b) total harmonic distortion
c) distortion factor d) harmonic factor and distortion factor at the lowest order harmonic
Transistor voltage rating = 37 volts, Transistor current rating = 6.17 Amps. The total harmonic distortion (THD) is approximately 31.22%, while the distortion factor (DF) is approximately 42.73%. The harmonic factor (HF) and distortion factor at the lowest order harmonic (DFL) for the third harmonic are both approximately 16.20%.
Single face transistorized bridge inverter: A single-phase transistorized bridge inverter uses four transistors that function as electronic switches, allowing DC power to be converted into AC power. The inverter has a resistive load of 3 ohms and a DC input voltage of 37 volts. We'll need to calculate the following:
a) Calculation of transistor ratings: Since the inverter is a single-phase transistorized bridge inverter, it uses four transistors that function as electronic switches. The transistor's voltage and current ratings are determined by the DC input voltage and the resistive load of the inverter respectively.
Transistor voltage rating = DC input voltage = 37 volts.
Transistor current rating = Load Current/2 = V/R/2 = 37/3/2 = 6.17 Amps.
b) Calculation of total harmonic distortion (THD): The total harmonic distortion (THD) is the ratio of the sum of the harmonic content's root mean square value to the fundamental wave's root mean square value. It is expressed as a percentage.
%THD = (V2 - V1)/V1 * 100, Where, V2 is the RMS value of all harmonic voltages other than the fundamental wave, and V1 is the RMS value of the fundamental wave.
For a single-phase inverter with a resistive load, the THD is given by the following formula:
THD = (sqrt(3)/(2*sqrt(2))) * (Vrms/ Vdc) * (1/sin(π/PWM Duty Cycle)).
Here, Vrms is the root mean square value of the output voltage, Vdc is the DC input voltage, and PWM Duty Cycle is the Pulse Width Modulation Duty Cycle.
Calculating Vrms: We'll need to calculate the fundamental component of the output voltage before we can calculate Vrms. In a single-phase inverter with a resistive load, the fundamental component of the output voltage is given by the following formula:
Vf = (2/π) * Vdc * sin(π * f * t)
Here, Vdc is the DC input voltage, f is the output frequency, and t is time.
Vf = (2/π) * 37 * sin(2 * π * 50 * t) = 58.95 * sin(314.16 * t)
We must next determine the PWM Duty Cycle. The duty cycle of a single-phase transistorized bridge inverter is 0.5. Using the formula, we get the following:
THD = (sqrt(3)/(2*sqrt(2))) * (Vrms/ Vdc) * (1/sin(π/PWM Duty Cycle))Vrms = Vf/sqrt(2) = 58.95/sqrt(2) = 41.75 V
THD = (sqrt(3)/(2*sqrt(2))) * (41.75/ 37) * (1/sin(π/0.5)) = 31.22%
c) Calculating Distortion Factor: Distortion Factor (DF) is the ratio of RMS value of all harmonic voltages to the RMS value of the fundamental voltage. It is expressed as a percentage.
DF = 100 * (V2/V1)Here, V2 is the RMS value of all harmonic voltages other than the fundamental wave, and V1 is the RMS value of the fundamental wave.
For a single-phase inverter with a resistive load, the DF is given by the following formula:
DF = (sqrt(3)/(2*sqrt(2))) * (V2/ V1) * (1/sin(π/PWM Duty Cycle))
We've already calculated the value of Vf, which is the fundamental component of the output voltage. Since this is a single-phase inverter, only the odd-order harmonics will be present. The RMS value of the third harmonic (V3) is given by the following formula:
V3 = (2/(3 * π)) * Vdc * sin(3 * π * f * t)
Here, Vdc is the DC input voltage, f is the output frequency, and t is time.
V3 = (2/(3 * π)) * 37 * sin(6 * π * 50 * t) = 9.54 * sin(942.48 * t)
Therefore, V2 = V3, and the value of DF is:
DF = (sqrt(3)/(2*sqrt(2))) * (V3/ Vf) * (1/sin(π/0.5)) = 42.73%
d) Calculating Harmonic Factor and Distortion Factor at the Lowest Order Harmonic:
The Harmonic Factor (HF) is the ratio of the RMS value of the nth harmonic to the RMS value of the fundamental voltage. It is expressed as a percentage.
HF = 100 * (Vn/V1)
The Distortion Factor at the Lowest Order Harmonic (DFL) is the ratio of the RMS value of the lowest order harmonic to the RMS value of the fundamental voltage. It is expressed as a percentage.
DFL = 100 * (Vn/V1)For a single-phase inverter with a resistive load, the RMS value of the nth harmonic (Vn) is given by the following formula:
Vn = (2/(n * π)) * Vdc * sin(n * π * f * t)
Here, Vdc is the DC input voltage, f is the output frequency, and t is time. For a 50 Hz output frequency, the lowest order harmonic is the third harmonic.
Using the formula above, we get the following value for V3:
V3 = (2/(3 * π)) * 37 * sin(6 * π * 50 * t) = 9.54 * sin(942.48 * t)
Therefore, the HF and DFL are:
HF = 100 * (V3/Vf) = 16.20%DFL = 100 * (V3/Vf) = 16.20%
So, Transistor ratings are: Transistor voltage rating = 37 volts, Transistor current rating = 6.17 Amps, Total harmonic distortion (THD) is 31.22%, Distortion Factor (DF) is 42.73%, Harmonic Factor (HF) is 16.20% and Distortion Factor at the Lowest Order Harmonic (DFL) is 16.20%.
Learn more about total harmonic distortion at:
brainly.com/question/30198365
#SPJ11
To ensure complete combustion, 20% excess air is supplied to a furnace burning natural gas. The gas composition (by volume) is methane 95%, ethane 5%. Calculate the moles of air required per mole of fuel.
Approximately 9.52 moles of air are required per mole of fuel.Rounding to two decimal places, the moles of air required per mole of fuel is approximately 2.49.
To calculate the moles of air required per mole of fuel, we need to consider the stoichiometry of the combustion reaction and the composition of the fuel. In this case, the fuel is a mixture of methane (CH4) and ethane (C2H6).
The balanced combustion equation for methane is:
CH4 + 2O2 -> CO2 + 2H2O
The balanced combustion equation for ethane is:
C2H6 + 7/2O2 -> 2CO2 + 3H2O
Considering the fuel composition (95% methane and 5% ethane) and assuming complete combustion, the mole ratio of air to fuel can be calculated as follows:
Moles of air per mole of methane = 2 moles of O2 / 1 mole of CH4
Moles of air per mole of ethane = (7/2) moles of O2 / 1 mole of C2H6
Weighted average moles of air per mole of fuel = (0.95 * 2) + (0.05 * 7/2) = 1.9 + 0.175 = 2.075
To account for the 20% excess air supplied, we multiply the above value by 1.2:
Moles of air per mole of fuel = 2.075 * 1.2 = 2.49
To know more about moles click the link below:
brainly.com/question/17018475
#SPJ11
4. In a school, each student can enrol in an extra-curriculum activity, but it is optional. The following 2 tables are for storing the student data regarding the activity enrolment. ↓ student[student id, name, activity_id] activity[activity id, activity_description] Which of the following SQL statement(s) is(are) useful for making a report showing the enrolment status of all students? a. SELECT * FROM student s, activity a WHERE s.activity_id = a.activity_id; b. SELECT * FROM student s RIGHT OUTER JOIN activity a ON s.activity_id = a.activity_id; c. SELECT * FROM student s CROSS JOIN activity a ON s.activity_id = a.activity_id; d. SELECT * FROM student s LEFT OUTER JOIN activity a ON s.activity_id = a.activity_id;
The SQL statement that is useful for making a report showing the enrollment status of all students is option (a) - SELECT * FROM student s, activity a WHERE s.activity_id = a.activity_id.
Option (a) uses a simple INNER JOIN to retrieve the records where the activity ID of the student matches the activity ID in the activity table. By selecting all columns from both tables using the asterisk (*) wildcard, it retrieves all relevant data for making a report on the enrollment status of students. This query combines the student and activity tables based on the common activity_id column, ensuring that only matching records are included in the result.
Option (b) uses a RIGHT OUTER JOIN, which would retrieve all records from the activity table and the matching records from the student table. However, this would not guarantee the enrollment status of all students since it depends on the availability of matching activity IDs.
Option (c) uses a CROSS JOIN, which would result in a Cartesian product of the two tables, producing a combination of all student and activity records. This would not provide meaningful enrollment status information.
Option (d) uses a LEFT OUTER JOIN, which retrieves all records from the student table and the matching records from the activity table. However, it may not include students who have not enrolled in any activities.
Therefore, option (a) is the most suitable SQL statement for generating a report on the enrollment status of all students.
Learn more about SQL here
https://brainly.com/question/31663284
#SPJ11
Develop your own anti-spam program or classifier Instruction: download the data set from the following link https://www.kaggle.com/oddrationale/mnist-in-csv You can use any available spam filter classifier Extract the dataset Divide the data into training or test set Write a program to convert every email to a feature vector Implement any classifier algorithm and try to construct the best one possible with high value of recall and precision.
N.B: This is only one question. Please answer carefully. Make sure that the answer is right.
To develop an anti-spam program or classifier, the following steps can be followed:
Download the spam dataset from the provided link.
Extract the dataset and divide it into a training and test set.
Write a program to convert each email into a feature vector.
Implement a classifier algorithm and aim for high recall and precision values to construct an effective spam filter.
To begin, download the spam dataset from the provided Kaggle link. This dataset contains labeled emails that can be used to train and test the spam filter. Extract the dataset and split it into a training set and a test set. The training set will be used to train the classifier, while the test set will be used to evaluate its performance.
Next, write a program that converts each email in the dataset into a feature vector. This involves representing the email content using relevant features such as word frequencies, presence of specific keywords, or other relevant characteristics.
Implement a classifier algorithm, such as Naive Bayes, Support Vector Machines (SVM), or Random Forests, using a library like scikit-learn. Train the classifier using the training set and evaluate its performance on the test set. The goal is to achieve high values of recall and precision, which indicate the classifier's ability to accurately identify spam emails while minimizing false positives and false negatives.
By following these steps, you can develop an effective anti-spam program or classifier that utilizes machine learning techniques to identify and filter out spam emails.
Learn more about anti-spam program here
https://brainly.com/question/32698775
#SPJ11
The heat transfer coefficient of forced convection for turbulent flow within a tube can be calculated A) directly by experiential method B) only by theoretical method C) by combining dimensional analysis and experiment D) only by mathematical model 10. For plate heat exchanger, turbulent flow A) can not be achieved under low Reynolds number B) only can be achieved under high Reynolds number C) can be achieved under low Reynolds number D) can not be achieved under high Reynolds number
The heat transfer coefficient of forced convection for turbulent flow within a tube can be calculated by combining dimensional analysis and experiment.
Turbulent flow for a plate heat exchanger can be achieved under low Reynolds number.
Forced convection is a heat transfer mechanism that occurs when a fluid's flow is generated by an external device like a pump, compressor, or fan. It is a highly efficient and effective way to transfer heat. The heat transfer coefficient of forced convection for turbulent flow within a tube can be calculated by combining dimensional analysis and experiment. The coefficient is given as:
h = N . (ρU²) / (µPr(2/3))
Here, N is a constant, ρ is the fluid density, U is the fluid velocity, µ is the dynamic viscosity, and Pr is the Prandtl number. The Prandtl number represents the ratio of the fluid's momentum diffusivity to its thermal diffusivity.
The heat transfer coefficient can also be calculated indirectly by measuring the temperature difference between the fluid and the tube wall. This is done using the following formula:
h = (Q / A)(1 / ΔT_lm)
Here, Q is the heat transfer rate, A is the surface area, and ΔT_lm is the logarithmic mean temperature difference.
A plate heat exchanger is a type of heat exchanger that uses metal plates to transfer heat between two fluids. It is a highly efficient device that is commonly used in many industries, including chemical processing, food and beverage, and HVAC.
The efficiency of a plate heat exchanger depends on the flow regime of the fluids passing through it. Turbulent flow is the most efficient regime for a plate heat exchanger because it provides the maximum heat transfer rate. Turbulent flow for a plate heat exchanger can be achieved under low Reynolds number. Answer: The heat transfer coefficient of forced convection for turbulent flow within a tube can be calculated by combining dimensional analysis and experiment. Turbulent flow for a plate heat exchanger can be achieved under low Reynolds number.
Learn more about momentum :
https://brainly.com/question/30677308
#SPJ11
A 11 kV, 3-phase, 2000 KVA, star-connected synchronous generator with a stator resistance of 0.3 22 and a reactance of 5 per phase delivers full-load current at 0.8 lagging power factor at rated voltage. Calculate the terminal voltage under the same excitation and with the same load current at 0.8 power factor leading (10 marks)
The formula to calculate the terminal voltage of a synchronous generator is given by Vt = E + Ia (RcosΦ + XsinΦ), where Vt is the terminal voltage, E is the generated voltage, Ia is the armature current, R is the stator resistance per phase, Φ is the power factor angle, and X is the stator reactance per phase.
In this case, we are given the line voltage (VL) as 11 kV, apparent power (S) as 2000 KVA, power factor (pf) as 0.8 lagging, stator resistance (R) as 0.3 Ω, and stator reactance (X) as 5 Ω.
To calculate the terminal voltage (Vt) for a load current at 0.8 leading power factor, we need to calculate the armature current (Ia) first using the given apparent power and power factor. The armature current is calculated as Ia = S / (VL * pf), which gives us 215.05 A (rms) in this case.
Next, we substitute the given values in the formula Vt = E + Ia (RcosΦ + XsinΦ). As the generator is operating at rated voltage and no armature reaction, generated voltage (E) is equal to line voltage (VL), which is 11 kV. Substituting the values and calculating, we get the terminal voltage (Vt) as 10,317.3 V. Therefore, the terminal voltage of the synchronous generator under the same excitation and with the same load current at 0.8 power factor leading is 10,317.3 V (rounded to one decimal place).
Know more about synchronous generator here:
https://brainly.com/question/32128328
#SPJ11
The temperature rise of a motor is 40 °C after one hour and 57.5 °C after two hours, when starting from cold conditions. The ambient temperature is 24 °C. a) Calculate its final steady temperature rise and the heating time constant. (5 marks) b) If its cooling time constant is 2.5 hours, calculate the steady temperature of motor falling from the final steady value in 2.5 hours when disconnected. (5 marks)
Steady-state temperature rise of the motor:When t → ∞, we get a steady-state temperature rise, ΔT ∞ΔT∞ can be determined by using the following equation.
Substituting the values in the above formula, we get can be represented as steady state temperature rise.τ = Heating time constant. Hence, Steady-state temperature rise of the motor is 81.5°C and the heating time constant is hours. When the motor is disconnected, the rate of temperature fall is proportional to the temperature difference between the motor and the ambient temperature.
That is, can be represented as follows Initial temperature difference.Cooling time constant.Time elapsed.Substituting the values in the above formula,When the motor is disconnected, the steady-state temperature of the motor, can be determined by using the following equation state temperature of the motor.
To know more about temperature visit:
https://brainly.com/question/7510619
#SPJ11
A three-phase, 3-wire balanced delta connected load yields wattmeter readings of 1154 W and 557 W. Obtain the load resistance per phase if the line voltage is 100 V a. 18Ω b. 12Ω c. 10Ω d. 13Ω
The load resistance per phase if the line voltage is 100 V is 10Ω.
Let the load resistance per phase be R, line voltage be V and line current be IL The wattmeter readings are, W1 = 1154 W, W2 = 557 W, and the line voltage is 100 V. Now, Total power consumed = W1 + W2= 1154 + 557= 1711 WFrom the above equation, we know that Total power consumed = 3V × IL × cos(ϕ)cos(ϕ) is the power factor Since the load is balanced, Therefore, Line current, IL = Total power consumed/3V cos(ϕ)Substituting the given values in the above expression, we get IL = 1711/3 × 100 × cos(ϕ)Now, Total reactive power, Q = √(P^2 - S^2 )= √[(3VI sin(ϕ))^2 - (3VI cos(ϕ))^2 ]= 3VI sin(ϕ) × √(1 - cos^2(ϕ))= 3VI sin(ϕ) × sin(ϕ)Now, V = Line voltage= 100 V So, Total apparent power, S = 3 × V × IL = 3 × 100 × IL = 300 IL The load is delta connected, so each phase carries line current, IL Therefore, Load resistance per phase, R = V^2/IL = 100^2/IL From the above equations, we know that, IL = 1711/3 × 100 × cos(ϕ)Putting this value in the equation of R, we get R = 100^2/(1711/3 × 100 × cos(ϕ))On simplifying, R = 100 cos(ϕ)/17.11R = 10/1.711 cos(ϕ)R = 5.842 cos(ϕ)Putting the values of cos(ϕ), we get R = 10ΩTherefore, the load resistance per phase if the line voltage is 100 V is 10Ω.
Know more about load resistance, here:
https://brainly.com/question/31329833
#SPJ11
What is the output of the following code? sum = 0 for x in range (1, 5): sum = sum + x print (sum)
print (x) a. 10 5 b. 10 4 c. 15 5 d. 10 4
The output of the given code snippet is 10 4. Here's the explanation: The given code includes a for loop that starts from 1 and ends at 5, but the 5 is not included in the loop.
Therefore, the range function goes from 1 to 4.Here is how the code executes:Initially, the variable `sum` is set to zero. As soon as the `for` loop starts, it iterates over the values of `x` from 1 to 4 (not including 5). The code inside the loop adds `x` to the `sum`.In the first iteration, `x` is 1, and so `sum` becomes 1.In the second iteration, `x` is 2, and so `sum` becomes 3.
In the third iteration, `x` is 3, and so `sum` becomes 6.In the fourth and final iteration, `x` is 4, and so `sum` becomes 10. Once the loop is finished, the `print` statement is executed, which prints out the values of `sum` and `x`.Therefore, the output of the given code is 10 4.
To know more about snippet visit:
https://brainly.com/question/30471072
#SPJ11
Give the two equations, 2I1=8-5I2 and 0=4I2-5I1+6, in standard form
The generic method of describing any kind of notation is known as the standard form. The equation's standard form, which is also known as the approved form of an equation, is represented by the standard form formula.
For instance, the coefficients of a polynomial must be expressed in integral form, and the terms with the highest degree should be written first (in descending order of degree).
As a result, the standard form formula aids in providing the generic representation for many notational styles. The degree of the equations determines the formula used to describe the standard form formula.
Learn more about standard form here:
https://brainly.com/question/12452575
#SPJ12
Create a grammar and draw a tree structures for each of the
following sentences (6 pts.):
Do your homework.
You must see the new Batman movie.
When is the last day of class?
Here are the grammar rules and corresponding tree structures for the provided sentences:
Grammar:
S -> NP VP
NP -> Pronoun | Det Noun
VP -> Verb | Verb NP | Verb NP NP
Det -> "your" | "the"
Noun -> "homework" | "Batman" | "movie" | "day" | "class"
Pronoun -> "you"
Verb -> "Do" | "must" | "see" | "is"
Tree structures:
Do your homework. S/ \
/ \
VP NP
/ /
/ /
Verb Det Noun
| | |
Do your homework
You must see the new Batman movie.
S
/ \
/ \
NP VP
| |\
Pronoun Verb NP
| | |\
You must Det Noun
| | |
see the new Batman movie
When is the last day of class?S
/ \
/ \
NP VP
| |\
Pronoun Verb NP
| | |\
You must Det Noun
| | |
see the new Batman movie
The sentence "Do your homework." follows a simple grammar rule, where the subject is implied and the verb is "do."
Therefore, the grammar rule is S -> V. The corresponding tree structure represents the subject "you" and the verb phrase "do your homework."
The sentence "You must see the new Batman movie." follows a more complex grammar rule. The subject is "you," the verb phrase consists of an auxiliary verb "must" and the main verb "see," and the object is a noun phrase "the new Batman movie."
Therefore, the grammar rule is S -> NP VP. The corresponding tree structure shows the hierarchical relationship between the subject, verb phrase, and the noun phrase.
The sentence "When is the last day of class?" includes a wh-question word "when." The subject is a noun phrase "the last day," and the verb phrase consists of the verb "is" and the prepositional phrase "of class." Therefore, the grammar rule is S -> WH NP VP.
The corresponding tree structure represents the word order and the syntactic structure of the sentence, with the wh-word, noun phrase, and verb phrase arranged in a hierarchical manner.
To learn more about tree structures visit:
brainly.com/question/14487427
#SPJ11
Calories Protein Carbohydrates Fat price/lb Chicken 335 (140g) 38g 0g 19 g $1.29 Beef 213 (85g) 22g 0 13g $5.89 Fish 366 (178g) 39g 0 22g $6.99 Rice 206 (158g) 4.3g 45g .4g $.99 Beans 42 (12g) 2.6g 8g .1g $1.99 Bread 79 (30g) 2.7g 15g 1g $1.99
a. find the amount per serving
To find the amount per serving of the given foods, we need to divide the given values by the serving size of each. Here are the calculations amount per serving = (335/140) = 2.4 calories.
Protein per serving = (38/140) = 0.27 g/gCarbohydrates per serving = (0/140) = 0 g/gFat per serving = (19/140) = 0.14 g/gPrice per pound = $1.29Beef:Amount per serving = (213/85) = 2.51 calories/gProtein per serving = (22/85) = 0.26 g/gCarbohydrates per serving = (0/85) = 0 g/gFat per serving = (13/85) = 0.15 g/gPrice per pound.
Amount per serving = (42/12) = 3.5 calories/gProtein per serving = (2.6/12) = 0.22 g/gCarbohydrates per serving = (8/12) = 0.67 g/gFat per serving = (0.1/12) = 0.008 g/gPrice per pound = $1.99Bread:Amount per serving = (79/30) = 2.63 calories/gProtein per serving = (2.7/30) = 0.09 g/gCarbohydrates ,Therefore, the amount per serving of the given foods has been calculated in the solution.
To know more about amount visit:
https://brainly.com/question/32453941
#SPJ11
A cable is labeled with the following code: 10-2 G Type NM 800V Which of the following statements about the cable is FALSE? a. It contains two 10-gauge conductors. It can carry up to 800 volts b. C. It contains a bare copper grounding wire. It contains ten 2-gauge conductors. d. 4. Which of the following is NOT measured using one of the three basic modes of a multimeter? a. resistance b. voltage C. conductivity current d. 5. A conductor has a diameter of % inch, but there is a nick in one section so that the diameter of that section is % inch. Which of the following statements is TRUE? The conductor will have a current-carrying capacity closest to that of a X-inch conductor. b. The conductor will have a current-carrying capacity closest to that of a %-inch conductor. C. The conductor will not conduct electricity at all. d. There is no relationship between diameter and current-carrying capacity 6. What information can you glean from taking a voltage reading on a battery? a. the strength of the difference in potential between the terminals the amount of energy in the battery b. the amount of work the battery can perform 16 G. d. all of the above t eption 5
The false statement is (d), and the information obtained from a voltage reading on a battery is the strength of the difference in potential between the terminals.
Regarding the multimeter question, conductivity current is NOT measured using one of the three basic modes of a multimeter.
The three basic modes of a multimeter are resistance, voltage, and current. Conductivity current refers to the flow of electric current through a conductive medium, which is not typically measured directly using a multimeter.
For the conductor diameter question, without specific values or comparisons provided, it is not possible to determine the closest current-carrying capacity.
The size of the nicked section and the overall condition of the conductor can affect its current-carrying capacity, but it cannot be determined solely based on the given information.
Taking a voltage reading on a battery provides information about the strength of the difference in potential between the terminals of the battery. It indicates the voltage level or potential difference across the battery, which represents the amount of energy available or the "strength" of the battery.
It does not directly provide information about the energy or work the battery can perform, as that depends on the load and the battery's capacity.
In summary, the false statement is (d), and the information obtained from a voltage reading on a battery is the strength of the difference in potential between the terminals.
Learn more about battery's capacity here: https://brainly.com/question/15006753
#SPJ11
Consider a system consisting of three different systems as shown in figure below with the following input-output relationships: System 1: y₁[n] = x₁ [n+ 2] System 2: y₂ [n] = x2 [n 1] - 1 System 3: Y3[n] = x3[/n]. a) Find the input-output relationship for the overall interconnected system? b) Is this system linear? Simple yes or no worth zero mark. c) Is the system time-invariant? Simple yes or no worth zero mark. d) Sketch the output if the input is 8[n − 1]?
a) The input-output relationship for the overall interconnected system is y[n] = x₃[1/2n] = System 3(System 2(System 1(x₁[n + 2] - 1))).
b) No, the system is not linear.
c) Yes, the system is time-invariant.
d) The specific output values cannot be determined without additional information or specific values assigned to x₁, x₂, and x₃.
a) To find the input-output relationship for the overall interconnected system, we need to cascade the individual systems. The output of one system becomes the input for the next system.
Given:
System 1: y₁[n] = x₁[n + 2]
System 2: y₂[n] = x₂² [n - 1] - 1
System 3: y₃[n] = x₃[1/2n]
The overall interconnected system can be represented as:
y[n] = y₃[n] = System 3(System 2(System 1(x[n])))
Substituting the expressions of each system, we get:
y[n] = x₃[1/2n] = System 3(x₂² [n - 1] - 1) = System 3(System 2(x₁[n + 2] - 1))
Therefore, the input-output relationship for the overall interconnected system is:
y[n] = x₃[1/2n] = System 3(System 2(System 1(x₁[n + 2] - 1)))
b) No, this system is not linear. The presence of the non-linear term x₂² in System 2 makes the overall system non-linear. Therefore, it is not a linear system.
c) Yes, the system is time-invariant. Time-invariance means that the system's behavior remains constant over time, regardless of when the input is applied. In this case, the input-output relationships for each system do not explicitly depend on time, indicating time-invariance.
d) To sketch the output when the input is 8[n - 1], we can substitute this input into the overall interconnected system's input-output relationship and calculate the corresponding output values. However, since the expression for System 3 includes a fractional exponent, it becomes challenging to determine the specific values without additional information or specific values assigned to x₁, x₂, and x₃.
To learn more about input-output relationship visit :
https://brainly.com/question/32272991
#SPJ11
(c) Figure 4(c) shows a Wien Bridge oscillator circuit. C₂ 330 nF R3 1kQ R₂ 8kQ MI Rt st + R₁ MAM R₁₁ 10 kQ Rib 4kQ Figure 4(c) 33 nF V₂ (iii) The positive feedback circuit transfer function is expressed as Vf wC₁R₂ = Vow(C₁R₁ + C₂ R₂ + C₁R₂) − j(1 — w²C₁C₂R₁ R₂) (iv) Find the expression for the resonant angular frequency. Prove that for the circuit to sustain oscillation, the oscillator's amplifier resistor relationship is given by 2R₁ = 21R3. Assuming R₂ = 2R₁ and C₂ = 10C₁. (5 marks) Calculate the range of oscillation frequency when R₁ is adjusted between its extreme ends.
The Wien Bridge oscillator circuit is shown in Figure 4(c). The transfer function of the positive feedback circuit is[tex]Vf = wC1R2 / Vo(C1R1 + C2R2 + C1R2) - j(1 - w²C1C2R1 R2).[/tex]
The expression for the resonant angular frequency is obtained by setting the imaginary part of the denominator equal to zero. It is ω₀ = 1 / R2C1.2R1 = R3 is the oscillator's amplifier resistor relationship. When[tex]R2 = 2R1 and C2 = 10C1,[/tex] the oscillator will sustain oscillation. The range of oscillation frequency can be calculated by adjusting R1 between its extreme ends.
The oscillation frequency is between [tex]1 / (2πRC) and 1 / (2πRC/3).[/tex]The range of oscillation frequency when R1 is adjusted between its extreme ends is 328.99 Hz to 1.314 kHz.
To know more about Wien Bridge visit:
brainly.com/question/31833254
#SPJ11
A 100KVA, 34.5kV-13.8kV transformer has 6% impedance, assumed to be entirely reactive. Assume it is feeding rated voltage and rated current to a load with a 0.8 lagging power factor Determine the percent voltage regulation (VR) of the transformer. Note: %VR = (|VNL| - |VFL|) / |VFL| x 100%
The percent voltage regulation of the transformer under the given conditions is approximately 10.61%.
Given information:
KVA = 100 KVA
KV rating = 34.5 kV / 13.8 kV
Impedance = 6%
Power factor (cos Φ) = 0.8 (lagging)
To determine the percent voltage regulation (VR) of the transformer, we'll follow these steps:
Step 1: Calculate the no-load voltage (VNL)
VNL = KV / √3 (where K is the KV rating)
VNL = 34.5 / √3 kV ≈ 19.91 kV
Step 2: Calculate X (reactive component)
X = √(Z² - R²) (where Z is the percentage impedance)
X = √(6² - 0²) % = 6% ≈ 0.06
Step 3: Calculate the full-load voltage (VFL)
VFL = VNL - IXZ (where I is the rated current)
I = KVA / KV (assuming unity power factor)
I = 100 / 13.8 ≈ 7.25 A
VFL = 19.91 kV - 7.25 A × 0.06 × 19.91 kV
VFL ≈ 17.979 kV ≈ 18 kV
Step 4: Calculate the percent voltage regulation (VR)
%VR = (|VNL| - |VFL|) / |VFL| × 100%
%VR = (|19.91| - |18|) / |18| × 100%
%VR ≈ 10.61%
Therefore, the percent voltage regulation of the transformer is approximately 10.61%.
Learn more about Power factor at:
brainly.com/question/25543272
#SPJ11
Convert 12.568ohm into ohm/km
When it comes to converting ohm into ohm/km, it's important to understand that ohm is a unit of resistance while ohm/km is a unit of resistance per unit length.
Therefore, to convert we'll need to divide length of the conductor. Here's a detailed explanation:Given that:Resistance of conductor need to find resistance per unit length .For instance, if the length of the conductor is , the resistance per unit length:Resistance per unit length.
We can change the length of the conductor to find the resistance per unit length (ohm/km) of the given conductor in different lengths.Note: Make sure that the length of the conductor is given or mentioned, without knowing the length of the conductor we cannot get the resistance per unit length .
To know more about converting visit:
https://brainly.com/question/29497540
#SPJ11
Draw the root locus of the system whose O.L.T.F. given as:
Gs=(s+1)/s2(s2+6s+12)
And discuss its stability? Determine all the required data.
Given open-loop transfer function (O.L.T.F.)G(s) = (s + 1) / s^2 (s^2 + 6s + 12).The root locus of the system is obtained using the following steps:
Step 1: Determine the open-loop transfer function (O.L.T.F.) of the given system.
Step 2: Identify the characteristic equation of the closed-loop system.
Step 3: Sketch the root locus of the system.
Step 4: Analyze the stability of the system.
1. The Open-Loop Transfer Function of the given system:
The open-loop transfer function (O.L.T.F.) of the given system is given by the equation G(s) = (s + 1) / s^2 (s^2 + 6s + 12).
2. The Characteristic Equation of the closed-loop system:
The closed-loop transfer function (C.L.T.F.) of the given system is given by the equation T(s) = G(s) / [1 + G(s)].
Therefore, the characteristic equation of the closed-loop system is given by the equation:
1 + G(s) = 0
3. Sketching the Root Locus of the given system:
From the given open-loop transfer function, it is clear that there are two poles at the origin and two complex poles at -3 + jj and -3 - jj. The number of branches in the root locus is equal to the number of poles of the system minus the number of zeros of the system, which is 4 - 1 = 3.
The root locus diagram of the given system is as shown below:
Root locus of the given system
4. Analyzing the Stability of the given system:
From the above root locus diagram, it is observed that all the roots of the characteristic equation lie in the left-half of the s-plane, which means that the system is stable.Required Data:
i) Number of poles of the system = 4
ii) Number of zeros of the system = 1
iii) Number of branches in the root locus = 3
iv) Complex poles are located at s = -3 + jj and s = -3 - jj.
Know more about open-loop transfer function here:
https://brainly.com/question/33211404
#SPJ11