A company has a fixed cost of $24,000 and a production cost of $12 for each disposable camera it manufactures. Each camera sells for $20. a) What are the cost, revenue, and profit functions? b) Find the profit (loss) corresponding to production levels of 2500 and 3500 units, respectively. c) Sketch a graph of the cost and revenue functions. d) Find the break-even point for the company algebraically.

Answer:

The coordinates are,

[tex]x=1/2,\\y=-\sqrt{3} /2\\\\\\And \ the \ point \ is,\\P(1/2, -\sqrt{3}/2)[/tex]

Step-by-step explanation:

Since we move t = 11pi/3 units on the cricle,

the angle is t,

Now, for a unit circle,

The x coordinate is given by cos(t)

And, the y coordinate is given by sin(t),

so,

[tex]x=cos(11\pi /3)\\x = 1/2\\y = sin(11\pi /3)\\y= -\sqrt{3}/2[/tex]

So, the coordinates for the point are,

x = 1/2, y = -(sqrt(3))/2

To find the particular solution using the method of variation of parameters, we first need to determine the complementary solution by solving the homogeneous equation.

The homogeneous equation is given as: sin(x)y' + (2 sin(x)cos(x))y = 0

To solve this, we assume the solution is of the form y = e^(rx). Taking the derivative of y, we get y' = re^(rx).

Substituting these into the equation, we have:
sin(x)(re^(rx)) + (2 sin(x)cos(x))(e^(rx)) = 0

Rearranging the terms, we get:
e^(rx)(sin(x)r + 2sin(x)cos(x)) = 0

Since e^(rx) is never zero, we can equate the expression inside the parentheses to zero:
sin(x)r + 2sin(x)cos(x) = 0

Dividing through by sin(x), we have:
r + 2cos(x) = 0

Solving for r, we get:
r = -2cos(x)

Therefore, the complementary solution is given by:
y_c = e^(-2cos(x)x)

Next, we can find the particular solution using the method of variation of parameters.

We assume the particular solution is of the form y_p = u_1(x)y_1 + u_2(x)y_2, where y_1 and y_2 are the solutions of the homogeneous equation and u_1(x) and u_2(x) are functions to be determined.

The solutions y_1 and y_2 are given as:
y_1 = e^x
y_2 = e^(cos(x))

To find u_1(x) and u_2(x), we use the following formulas:

u_1(x) = -∫(y_2 * g(x))/(W(y_1, y_2)) dx
u_2(x) = ∫(y_1 * g(x))/(W(y_1, y_2)) dx

where W(y_1, y_2) is the Wronskian of y_1 and y_2, and g(x) = e^x / (sin(x)cos(x)).

The Wronskian can be calculated as:
W(y_1, y_2) = y_1y_2' - y_2y_1'

Substituting the values of y_1 and y_2, we get:
W(y_1, y_2) = e^x * (-sin(x) * e^(cos(x))) - e^(cos(x)) * (e^x)

Simplifying further, we have:
W(y_1, y_2) = -e^(x+cos(x))sin(x) - e^(x+cos(x))

Now we can calculate u_1(x) and u_2(x) using the formulas above.

Finally, the particular solution is given by:
y_p = u_1(x)y_1 + u_2(x)y_2

Learn more about homogeneous equation

https://brainly.com/question/30409992

#SPJ11

The value of x in the triangle is 3√2. The correct option is A.

To determine the value of x in the given triangle, we can use the Pythagorean theorem. According to the Pythagorean theorem, in a right triangle, the square of the length of the hypotenuse (the side opposite the right angle) is equal to the sum of the squares of the lengths of the other two sides.

In the given triangle, we have the length of one side as 3√2 and the length of the other side as x. The hypotenuse has a length of 6.

Using the Pythagorean theorem, we can write the equation:

(3√2)^2 + x^2 = 6^2

Simplifying, we have:

18 + x^2 = 36

Subtracting 18 from both sides:

x^2 = 18

Taking the square root of both sides:

x = √18

Simplifying, we get:

x = 3√2

As a result, the triangle's value of x is 3√2. The right answer is A.

for such more question on triangle

https://brainly.com/question/17335144

#SPJ8

If a rectangular beam has a width of 312mm and a total depth of 463mm. The total factored uniform load including the beam weight considers a moment capacity reduction of 0.9 is 37.24 kN/m (Rounded to two decimal places).

To determine the total factored uniform load on the rectangular beam, we need to consider the beam weight and the moment capacity reduction. Let's break it down step by step:

1. Calculate the self-weight of the beam:
The self-weight of the beam can be determined by multiplying the volume of the beam by the unit weight of concrete. Since we know the width, depth, and length of the beam, we can calculate the volume using the formula:
Volume = Width × Depth × Length

In this case, the width is 312mm (or 0.312m), the depth is 463mm (or 0.463m), and the length is 11m. The unit weight of concrete is typically taken as 24 kN/m³. Substituting the values into the formula, we get:

Volume = 0.312m × 0.463m × 11m

= 1.724m³
Self-weight = Volume × Unit weight of concrete

= 1.724m³ × 24 kN/m³

= 41.376 kN

2. Determine the moment capacity reduction factor:
The moment capacity reduction factor, denoted as φ, is given as 0.9 in this case. This factor is used to reduce the maximum moment capacity of the beam.

3. Calculate the total factored uniform load:
The total factored uniform load includes the self-weight of the beam and any additional loads applied to the beam. We'll consider only the self-weight of the beam in this case.
Total factored uniform load = Self-weight × φ
Substituting the values, we have:
Total factored uniform load = 41.376 kN × 0.9

= 37.2384 kN

You can learn more about rectangular beams at: brainly.com/question/29442816

#SPJ11

To find the value of x, we set HB equal to HA and solve for x: 2x - 46 = 24, therefore x = 35.

To find the value of x, we can set HA equal to HB and solve for x.

Given that HA = 24 and HB = 2x - 46, we can set up the equation:

24 = 2x - 46.

To isolate the variable x, we can start by adding 46 to both sides of the equation:

24 + 46 = 2x - 46 + 46

70 = 2x

Next, we divide both sides of the equation by 2 to solve for x:

70 / 2 = 2x / 2

35 = x

Therefore, the value of x is 35.

By substituting x = 35 back into the original equation, we can verify the solution:

HA = 24 and HB = 2x - 46

HA = 24

HB = 2(35) - 46

HB = 70 - 46

HB = 24

Since HA and HB are equal, and the value of x = 35 satisfies the equation, we can conclude that x = 35 is the correct value.

For similar question on equation.

https://brainly.com/question/17145398  

#SPJ8

Constitutive equations are the relationship between stresses and strains that assist in the formulation of models for the behavior of materials.

They are often written mathematically as equations or in the form of a table.The algorithm to develop a model using a constitutive relationship is given below:

Algorithm:

Data collection is the first step in this process. The properties of the materials that will be used in the model must be gathered, as well as the material behavior that the model will aim to predict.

Select the appropriate type of constitutive equation for the material under consideration. This is determined by the material's nature and the modeling goal.

Choose the parameters for the equation. These parameters are based on the information gathered in the first step.

Apply the chosen constitutive equation to the model to simulate the material's behavior.

Compare the simulated results to the actual behavior of the material and adjust the parameters of the constitutive equation until the simulated behavior closely matches the actual behavior.

To improve the accuracy of the model, repeat steps 4 and 5 as many times as necessary.

Flow Diagram:To develop a model using a constitutive equation, follow the flow diagram given below:

Start

Collect material properties and information on its behavior

Choose an appropriate type of constitutive equation

Select the parameters for the equation

Use the equation to simulate material behavior in the model

Compare simulated results to actual behavior

Adjust parameters as necessary

Repeat steps 4-7 until the model accurately simulates the material behavior

End

Therefore, this is how a model is developed using a constitutive relation and the algorithm with a flow diagram to develop a model using a constitutive relation.

To know more about constitutive visit :

brainly.com/question/32581830

#SPJ11

The variational approach in Sobolev spaces allows us to obtain classical solutions directly from equations, even if the standard derivative does not exist for some functions. Classical solutions to the boundary value problem are always weak solutions.

The standard derivative is a well-known concept in calculus, representing the instantaneous rate of change of a function with respect to its variable. However, not all functions have a standard derivative, especially when dealing with more complex functions or discontinuous ones. In such cases, the concept of a weak derivative comes into play.

A weak derivative is a broader concept that extends the notion of a standard derivative to a wider class of functions, allowing us to handle functions with certain types of discontinuities or irregular behavior. It is a distributional derivative, and while it might not exist in the classical sense, it still provides valuable information about the function's behavior.

The variational approach is a powerful technique in functional analysis that enables us to obtain solutions to partial differential equations (PDEs) and boundary value problems by minimizing certain energy functionals.

By utilizing this approach within Sobolev spaces, which are function spaces containing functions with weak derivatives, we can derive classical solutions to equations, even for functions that lack standard derivatives.

Sobolev spaces, denoted by [tex]W^k[/tex],p, are spaces of functions whose derivatives up to a certain order k are in the [tex]L^p[/tex] space, where p is a real number greater than or equal to 1. These spaces play a crucial role in dealing with weak solutions, as they provide a suitable framework for functions that may not possess classical derivatives.

By working within Sobolev spaces, we can handle functions with certain irregularities and still obtain meaningful solutions to problems.

Learn more about  Standard derivative

brainly.com/question/32908379

#SPJ11

The diameter of the spherical particle is approximately 0.023 m. Density of spherical particle = 2000 kg/m³, Density of air = 1.2 kg/m³ and Viscosity of air = 18 × 10⁻⁶ Pa s

Formula used:

Stokes' law states that the force acting on a particle is given by F = 6πrvη, where

F is the force acting on the particle,

r is the radius of the particle,

v is the velocity of the particle,

η is the viscosity of the fluid.

Equating the buoyancy force and the viscous force on the particle, we have:

4/3 × πr³ (ρp - ρf)g = 6πrvη,

where

g is the acceleration due to gravity,

ρp is the density of the particle,

ρf is the density of the fluid.

Rearranging the above equation, we get:

r = ((2*(ρp - ρf)*V)/(9η*g))^0.5,

where V is the volume of the spherical particle.

Assuming the particle is spherical, then the diameter of the spherical particle is given by the formula: d = 2r.

Formula substituted:

ρp = 2000 kg/m³

ρf = 1.2 kg/m³

η = 18 × 10⁶ Pa s

Let the diameter be d. Then the radius is r = d/2.

Using Stokes' law, the radius of the spherical particle is:

r = [2×(ρp-ρf)×V]/[9×η×g]

Given that the density of the spherical particle is 2000 kg/m³,

so the mass of the particle is m = ρpV = (4/3)πr³ρp.

The buoyant force acting on the particle is given by Fb = ρfVg = (4/3)π(d/2)³ρfg.

The weight of the particle is given by W = mg = (4/3)π(d/2)³ρpg.

Substituting the values of Fb and W in the equation Fb = 6πrηv, we have:

(4/3)×π×(d/2)³×ρfg = 6π×(d/2)×η×v,

=> d³ = (54ηv)/(ρg),

=> d = [(54ηv)/(ρg)]^(1/3).

Substituting the given values of ρf, η, and g, we get:

d = [(54×18×10⁻⁶ × 9.8)/(2000 - 1.2)]^(1/3),

d = 0.023 m (approximately).

Hence, the diameter of the spherical particle is approximately 0.023 m.

Learn more about Viscosity of air

https://brainly.com/question/30901839

#SPJ11

Slip is a mechanism in which atoms move along the crystal plane under stress. Slip planes are crystallographic planes in a crystal that allow for the most extensive movement of atoms during slip. Larger grain sizes are more ductile than smaller grain sizes.

Ceramics are intrinsically harder than metals, but their use as an engineering material is limited.

Here are 4 properties of ceramics which make them useful in an engineering context and how their properties are influenced by their atomic bonding arrangements.

1. Hardness: Ceramics are more challenging than metals, and their hardness makes them resistant to wear and corrosion. Their atomic bonding arrangements contribute to their hardness by creating strong covalent and ionic bonds.

2. High melting point: The majority of ceramics have high melting points, making them ideal for high-temperature applications. Their atomic bonding arrangement plays a crucial role in their high melting point, as the strong covalent and ionic bonds require a large amount of energy to break.

3. Low thermal expansion: Ceramics have a low thermal expansion coefficient, which makes them useful for high-temperature applications.

Their atomic bonding arrangements contribute to their low thermal expansion by forming strong and rigid structures.

4.Insulators: Ceramics have poor electrical conductivity, which makes them ideal electrical insulators.Their atomic bonding arrangements contribute to their poor electrical conductivity by limiting the movement of electrons.

4 specific applications of ceramics include: bio-ceramics (replacement joints, teeth), electronic components, refractory materials (kiln linings, furnace components), and thermal barrier coatings.

In relation to crystalline materials, slip is a mechanism in which atoms move along the crystal plane under stress.

Slip planes are crystallographic planes in a crystal that allow for the most extensive movement of atoms during slip.

The grain size affects the movement of slip planes in that larger grains have fewer grain boundaries and, therefore, more movement along slip planes.

Conversely, smaller grains have more grain boundaries, which limit movement along slip planes.

Hence, larger grain sizes are more ductile than smaller grain sizes.

To know more about slip plane visit :

https://brainly.com/question/31631295

#SPJ11

The complete question is-

a) Ceremics are intrinsically harder than metals. however their use as an engineering material is limited. Identify 4 properties of ceramics which make them useful in an enginnering context ,outline how their properties are influenced by their atomic bonding arrangments and give 4 specific applications of ceramics

b) In relation to crystalline materials, explain the term slip and slip planes. how does the grain size affect the movement of slip planes?

Describe and illustrate the slip planes found for either the FCC crystal structure or the BCC crystal structure. how many slip system does your chosen structure contain?

In crystalline materials, slip refers to the movement of dislocations (line defects) within the crystal lattice. Slip planes are specific crystallographic planes along which dislocations move most easily. These planes are determined by the crystal structure and atomic arrangement.

The grain size of a material affects the movement of slip planes. In materials with larger grain sizes, the presence of grain boundaries obstructs the movement of dislocations. This leads to a higher resistance to slip, resulting in increased strength. On the other hand, smaller grain sizes allow dislocations to move more easily, reducing the strength of the material. Therefore, grain size plays a critical role in the mechanical behavior of crystalline materials.

Ceramics have unique properties that make them useful in engineering applications. These properties are influenced by their atomic bonding arrangements. Here are four properties of ceramics and their corresponding atomic bonding arrangements:

1. Hardness: Ceramics are known for their high hardness, which is attributed to their strong and rigid atomic bonding arrangements. They typically have ionic or covalent bonding, where atoms are held together by electrostatic attractions or shared electron pairs, respectively. For example, alumina (Al2O3) has a network of oxygen and aluminum atoms bonded through ionic interactions.

2. High melting point: Ceramics generally have high melting points due to their strong atomic bonding arrangements. The ionic or covalent bonds in ceramics require significant energy to break, leading to high melting temperatures. For instance, silicon carbide (SiC) has a melting point of about 2700°C, making it suitable for high-temperature applications like refractory linings in furnaces.

3. Chemical resistance: Ceramics are often chemically inert and resistant to corrosion. This property is influenced by their atomic bonding arrangements, which result in stable structures. For example, zirconia (ZrO2) exhibits excellent chemical resistance, making it suitable for applications in harsh chemical environments.

4. Electrical insulation: Ceramics are excellent electrical insulators due to their atomic bonding arrangements, which inhibit the movement of electrons. Ceramics with primarily ionic bonding, like porcelain, have high electrical resistivity and are widely used for insulating electrical wires and components.

Here are four specific applications of ceramics:

1. Cutting tools: Ceramic materials such as alumina and silicon nitride are used in cutting tools due to their exceptional hardness and wear resistance.

2. Biomedical implants: Bioinert ceramics like zirconia and alumina are used for dental implants, hip replacements, and other biomedical applications due to their biocompatibility and resistance to corrosion.

3. Heat shields: Ceramics like silica and alumina-based materials are utilized as heat shields in aerospace applications due to their high melting point and excellent thermal insulation properties.

4. Electronics: Ceramic materials such as piezoelectric ceramics (e.g., lead zirconate titanate) are used in electronic devices for their unique electrical and mechanical properties, like the ability to convert mechanical stress into electrical signals.

Learn more about crystalline

https://brainly.com/question/28274778

#SPJ11

a) The initial temperature (T₁) is 1080.21 °R, and the final volume (V₂) is 5 ft³.

b) The net amount of heat transfer to the water is approximately -72.75 Btu.

a) Calculate the initial temperature and final volume:

Given:

Mass of water (m) = 3.6 lbm

Pressure (P) = 160 psia

Initial volume (V₁) = 9 ft³

Final temperature (T₂) = 600 °F

The ideal gas law is given by:

PV = mRT

where P is the pressure, V is the volume, m is the mass, R is the specific gas constant, and T is the temperature.

To solve for the initial temperature (T₁), we can rearrange the equation as follows:

[tex]T_1= \frac{PV}{mR}[/tex]

R = 0.3703 psi·ft³/(lbm·°R).

Plugging in the values, we have:

T₁  [tex]=\frac{160\times9}{3.6\times0.3703}[/tex]

=1080.21 °R

To calculate the final volume (V₂), we can use the ideal gas law again:

V₂ = mRT₂ / P

Plugging in the values, we get:

[tex]V_2=\frac{3.6\times0.3703\times600}{160}[/tex]

Calculating this, we find:

V₂ =5 ft³

Therefore, the initial temperature (T₁) is 1080.21 °R, and the final volume (V₂) is 5 ft³.

b) Calculate the net amount of heat transfer:

To calculate the net amount of heat transfer (Q), we can use the equation:

Q = m×c ×ΔT

The change in temperature:

ΔT = (600 °F) - (1080.21 °R - 460 °R)

Converting 1080.21 °R  to °F, we get:

ΔT = 600 °F- 620.21  °F

ΔT = -20.21  °F

Now, we can calculate the net amount of heat transfer:

Q = (3.6 lbm) × (1 Btu/(lbm·°F)) × (-20.21°F)

Q= -72.75 Btu.

Therefore, the net amount of heat transfer to the water is approximately -72.75 Btu.

To learn more on Heat click here:

https://brainly.com/question/13860901

#SPJ4

10. If the pay period is changed to a weekly period, Edward will earn approximately P2,900 per week.

11. The monthly income for the salesperson, considering a total sales amount of P9,827, is approximately P7,013.50.

12. Roy's monthly income, with total sales amounting to P40,000, is approximately P3,290.

10. To determine Edward's weekly earnings, we can divide his monthly salary of P12,600 by the number of weeks in a month. Assuming a typical month has four weeks, we divide P12,600 by 4 to get his approximate weekly earnings of P2,900.

11. The salesperson's monthly income consists of the bi-weekly salary of P4,300 and a commission based on total sales. To calculate the commission, we multiply the total sales amount of P9,827 by 9.5% (or 0.095). Adding this commission to the bi-weekly salary gives us the monthly income of approximately P7,013.50.

12. Roy's commission structure is based on different percentages for different ranges of sales. We calculate the commission by applying the respective percentages to the corresponding sales ranges and summing them up. For the first P5,000, Roy earns 4.5% (or 0.045), which amounts to P225. For the next P12,000, he earns 5.5% (or 0.055), totaling P660. For sales over P17,000, Roy earns 7% (or 0.07), which is P1,260. By adding these commission amounts, we find his total monthly income to be approximately P3,290.

Learn more about : Considering

brainly.com/question/31466500

#SPJ11

The value of C(4,0) - C(4,1) + C(4,2) - C(4,3) + C(4,4) is 0. The expression you have provided is a simplified form of the binomial expansion of (x+y)⁴ when x = 1 and  y = -1.

In the binomial expansion, the coefficients of each term are given by the binomial coefficients, also known as combinations.

In this case, the expression C(4,0) - C(4,1) + C(4,2) - C(4,3) + C(4,4) represents the sum of the binomial coefficients of the fourth power of the binomial (x + y) with alternating signs.
Let's evaluate each term individually:
C(4,0) = 1
C(4,1) = 4
C(4,2) = 6
C(4,3) = 4
C(4,4) = 1

Substituting these values into the expression, we get:
1 - 4 + 6 - 4 + 1 = 0
Therefore, the value of C(4,0) - C(4,1) + C(4,2) - C(4,3) + C(4,4) is 0.

To know more about binomial expansion visit:

https://brainly.com/question/31363254

#SPJ11

The solution to the system is x = -41/36, y = 0, z = -17/8, w = -1/6 using Gauss-Jordan elimination.

To solve the given system of equations using Gauss-Jordan elimination, we'll perform row operations to reduce the augmented matrix to row-echelon form. Here's the step-by-step process:

Step 1: Write the augmented matrix:

[3 9 2 12 | 1]

[1 3 -2 4 | 2]

[2 -6 0 10 | 0]

Step 2: Perform row operations to introduce zeros below the leading entries of the first column:

R₂ = R₂ - (1/3)R₁

R₃ = R₃ - (2/3)R₁

The updated matrix becomes:

[3 9 2 12 | 1]

[0 0 -8/3 0 | 5/3]

[0 -12 -4/3 6 | -2/3]

Step 3: Perform row operations to introduce zeros below the leading entries of the second column:

R3 = R3 - (3/4)R2

The updated matrix becomes:

[3 9 2 12 | 1]

[0 0 -8/3 0 | 5/3]

[0 0 0 6 | -1]

Step 4: Perform row operations to convert the leading entry of the third row to 1:

R₃ = (1/6)R₃

The updated matrix becomes:

[3 9 2 12 | 1]

[0 0 -8/3 0 | 5/3]

[0 0 0 1 | -1/6]

Step 5: Perform row operations to introduce zeros above the leading entries of the third row:

R₁ = R₁ - 2R₃

R₂ = R₂ + (8/3)R₃

The updated matrix becomes:

[3 9 2 0 | 8/3]

[0 0 -8/3 0 | 17/3]

[0 0 0 1 | -1/6]

Step 6: Perform row operations to convert the leading entry of the second row to 1:

R₂ = (-3/8)R₂

The updated matrix becomes:

[3 9 2 0 | 8/3]

[0 0 1 0 | -17/8]

[0 0 0 1 | -1/6]

Step 7: Perform row operations to introduce zeros above the leading entries of the second row:

R₁ = R₁ - 2R₂

The updated matrix becomes:

[3 9 0 0 | 41/12]

[0 0 1 0 | -17/8]

[0 0 0 1 | -1/6]

Step 8: Perform row operations to introduce zeros above the leading entries of the first row:

R₁ = (-9/3)R₁

The updated matrix becomes:

[1 3 0 0 | -41/36]

[0 0 1 0 | -17/8]

[0 0 0 1 | -1/6]

Step 9: The augmented matrix is now in row-echelon form. The solution to the system of equations is:

x = -41/36

y = 0

z = -17/8

w = -1/6

Therefore, the solution to the system is x = -41/36, y = 0, z = -17/8, w = -1/6.

To know more about Gauss-Jordan elimination click here :

https://brainly.com/question/29004583

#SPJ4

Operational energy/emissions and embodied energy/emissions in the building sector are two distinct concepts related to the environmental impact of buildings

b) The key difference lies in the timing and scope of the energy and emissions. Operational energy/emissions occur during the building's use phase, while embodied energy/emissions occur before the building becomes operational, during the construction phase.

1. Energy-efficient design: Implementing energy-efficient building design practices can significantly reduce operational energy consumption. This includes using high-performance insulation, energy-efficient windows, energy-efficient HVAC systems, and energy-saving lighting solutions.

2. Sustainable materials: Opting for sustainable and low-carbon materials in construction can minimize embodied energy/emissions. Using recycled materials, locally sourced materials, and renewable resources can reduce the carbon footprint associated with construction.

3. Renewable energy integration: Incorporating renewable energy sources, such as solar panels or wind turbines, into the building's design can offset operational energy consumption with clean energy generation, leading to lower operational emissions.

These strategies can contribute to reducing the building sector's overall carbon footprint and fostering a more sustainable built environment.

Learn more about Operational energy/emissions

brainly.com/question/33796269

#SPJ11

To double the wind power, the blade length should be approximately 35.36 meters.

To compute the wind power potential, we can use the following formula:

Power = 0.5 × Cp × Air density × A × V³

Where:

Power is the wind power generated (in watts)

Cp is the power coefficient (dimensionless),

which represents the efficiency of the wind turbine

Air density is the density of air (in kg/m³)

A is the swept area of the rotor blades (in m²)

V is the wind velocity (in m/s)

Given:

Rotor blade length: 50 m

Air density: 1.23 kg/m³

Wind velocity: 15 m/s

Cp: 0.4

To double the wind power, we can assume that the only variable we change is the blade length, while keeping all other parameters the same.

Let's denote the new blade length as [tex]L_{new[/tex].

The swept area of the rotor blades (A) is proportional to the square of the blade length:

A = π × L²

The power generated (P) is directly proportional to the swept area:

P = K × A

Where K is a constant factor that includes Cp, air density, and the cube of the wind velocity.

For the original scenario:

[tex]P_{original[/tex] = 0.5 × Cp × Air density × A × V³

For the new scenario with double the power:

[tex]P_{new} = 2 * P_{original[/tex]

Substituting the expressions for [tex]P_{original[/tex] and [tex]P_{new[/tex]:

0.5 × Cp × Air density × A × V³ = 2 × (0.5 × Cp × Air density × [tex]A_{new[/tex] × V³)

Cp × Air density * A = 2 × Cp × Air density ×  [tex]A_{new[/tex]

Since Cp, air density, and V are constant, we can simplify the equation:

[tex]A_{new[/tex]  = A / 2

Now, let's compute the new blade length (L_new) based on the relation between the swept area and blade length:

[tex]A_{new[/tex]  = π ×  [tex]L_{new}[/tex]²

Substituting the value of  [tex]A_{new[/tex] :

π × [tex]L_{new[/tex]² = A / 2

Solving for  [tex]L_{new[/tex]:

[tex]L_{new[/tex]² = A / (2π)

[tex]L_{new[/tex] = √(A / (2π))

Substituting the value of A (which is proportional to the square of the blade length):

[tex]L_{new[/tex] = √((π × L²) / (2π))

[tex]L_{new[/tex] = √(L² / 2)

[tex]L_{new[/tex] = L / √2

Therefore, to double the wind power, the new blade length ( [tex]L_{new[/tex]) should be the original blade length (L) divided by the square root of 2.

In this case, if the original blade length is 50 m:

[tex]L_{new[/tex] = 50 m / √2

[tex]L_{new[/tex] ≈ 50 m / 1.414

[tex]L_{new[/tex] ≈ 35.36 m

So, to double the wind power, the blade length should be approximately 35.36 meters.

To know more about coefficient, visit

https://brainly.com/question/13431100

#SPJ11

The formula of the conjugate acid of HCO₂⁻ can be determined by adding a proton (H⁺) to the anion. HCO₂⁻ is a base as it can accept a proton to form a conjugate acid. The reaction between HCO₂⁻ and H⁺ forms the conjugate acid of HCO₂⁻, which is H₂CO₂.

The balanced equation for the formation of the conjugate acid of HCO₂⁻ is as follows:HCO₂⁻ + H⁺ → H₂CO₂H₂CO₂ is a weak acid that forms when CO₂ gas is dissolved in water. It can donate a proton to form the HCO₂⁻ anion. HCO₂⁻ is a stronger base than H₂CO₂ because it has a greater tendency to accept a proton and form a conjugate acid. Thus, H₂CO₂ is a weaker acid than HCO₂⁻.

The formation of the conjugate acid of HCO₂⁻ shows that the addition of a proton to a base forms a weaker acid, while the removal of a proton from an acid forms a weaker base.Answer: The formula of the conjugate acid of HCO₂⁻ is H₂CO₂.

To know more about conjugate acid visit:-

https://brainly.com/question/31229565

#SPJ11

The gas is placed into a closed container, and during a process, its pressure and temperature decrease. We need to determine the effect on the volume of the gas.

When the pressure and temperature of a gas decrease, we can apply the ideal gas law to analyze the situation. The ideal gas law states that the product of pressure and volume is directly proportional to the product of the number of moles of gas and the gas constant, and inversely proportional to the temperature.

P * V = n * R * T

In this case, we know that the pressure and temperature are decreasing. If we assume the number of moles of gas and the gas constant remain constant, we can rearrange the equation to understand the effect on the volume:

V = (n * R * T) / P

Since the pressure is decreasing, the numerator of the equation remains constant. As a result, the volume of the gas will increase. Therefore, we can say that when the pressure and temperature of a gas decrease, the volume increases.

To know more about ideal gas law :

https://brainly.com/question/30458409

#SPJ11

The number of iterations needed is the smallest integer greater than or equal to the calculated value of k.

To find the number of iterations needed to achieve a maximum error not greater than 0.5 x 10⁻⁴,

we need to use the iteration method [tex]x_k+1 = f(x_k).[/tex]
Given that the first and second iterates were computed as

x₁ = 0.50000 and

x₂ = 0.52661,

we can use these values to calculate the error.
The error is given by the absolute difference between the current and previous iterates, so we have:
error = |x₂ - x₁|
Substituting the given values, we get:
error = |0.52661 - 0.50000|

= 0.02661
Now, we need to determine the number of iterations needed to reduce the error to a maximum of 0.5 x 10⁻⁴.
Let's assume that after k iterations,

we achieve the desired maximum error.
Using the given condition |f'(x)| ≤ 0.53 for all values of x, we can estimate the maximum error in each iteration.
By taking the derivative of f(x),

we can approximate the maximum error as:
error ≤ |f'(x)| * error
Substituting the given condition and the error from the previous iteration, we get:
0.5 x 10⁻⁴ ≤ 0.53 * error
Simplifying this inequality, we have:
error ≥ (0.5 x 10⁻⁴) / 0.53
Now, we can calculate the maximum number of iterations needed to achieve the desired error:
k ≥ (0.5 x 10⁻⁴) / 0.53
Therefore, the number of iterations needed is the smallest integer greater than or equal to the calculated value of k.

To know more about integer, visit:

https://brainly.com/question/33503847

#SPJ11

A detailed explanation of the forces involved and their specific directions is necessary to provide a comprehensive answer.

To determine the direction of the force F when the particle is in equilibrium, we need to consider the concept of equilibrium.

In a state of equilibrium, the net force acting on the particle is zero. This means that the vector sum of all the forces acting on the particle should cancel out.

If we assume that A is equal to 12, we can analyze the forces and their directions to achieve equilibrium.

Cannot provide an answer in one row as the explanation requires more context and details.

Learn more about comprehensive answer

brainly.com/question/30853421

#SPJ11

The centroid in the x-direction of the shaded area can be found by calculating the weighted average of the x-coordinates of the area. Here is the step-by-step explanation:

To find the centroid in the x-direction of the shaded area, we calculate the weighted average of the x-coordinates of the centroids of the circular segment and rectangle. The x-coordinate of the centroid of the circular segment is determined by the midpoint of the chord, while the x-coordinate of the centroid of the rectangle is given. By applying the formula for the weighted average, we can determine the centroid in the x-direction.

Learn more about Centroid :

https://brainly.com/question/29756750

#SPJ11

the pH after the addition is 0.70.

To find the pH after 100.00 mL of 0.40 M HCIO4 have been added to a 100.00 mL solution of 0.40 M NH3, we need to consider the reaction between NH3 (ammonia) and HCIO4 (perchloric acid).

NH3 + HCIO4 -> NH4+ + CIO4-

Since NH3 is a weak base and HCIO4 is a strong acid, the reaction will proceed completely to the right, forming NH4+ (ammonium) and CIO4- (perchlorate) ions.

To determine the pH after the titration, we need to calculate the concentration of the resulting NH4+ ions. Since the initial concentration of NH3 is 0.40 M and the volume of NH3 solution is 100.00 mL, the moles of NH3 can be calculated as follows:

[tex]Moles of NH3 = concentration * volume[/tex]

[tex]Moles of NH3 = 0.40 M * 0.100 L = 0.040 mol[/tex]

Since NH3 reacts with HCIO4 in a 1:1 ratio, the moles of NH4+ ions formed will also be 0.040 mol.

Now, we need to calculate the concentration of NH4+ ions:

Concentration of NH4+ = [tex]moles / volume[/tex]

Concentration of NH4+ = 0.040 mol / 0.200 L (100.00 mL NH3 + 100.00 mL HCIO4)

Concentration of NH4+ = [tex]0.200 M[/tex]

The concentration of NH4+ ions is 0.200 M. To calculate the pH, we can use the fact that NH4+ is the conjugate acid of the weak base NH3.

NH4+ is an acidic species, so we can assume it dissociates completely in water, producing H+ ions. Therefore, the concentration of H+ ions is also 0.200 M.

The pH can be calculated using the equation:

pH = -log[H+]

[tex]pH = -log(0.200)[/tex]

Using a calculator, the pH after the addition of 100.00 mL of 0.40 M HCIO4 is approximately 0.70.

Therefore, the pH after the addition is 0.70.

To know more about volume visit:

brainly.com/question/28058531

#SPJ11

The required total limestone (CaCO3) dosage to reduce SO2, HCl, and HF emissions to the specified limits is 1,875 kg/day or 1.875 tons/day.

To calculate the limestone dosage, we need to determine the molar flow rates of SO2, HCl, and HF in the stack gas. Given the stack gas flowrate of 10,000 m3/hr and the uncontrolled emissions in mg/m3, we can convert these values to kg/hr as follows:

SO2 flow rate = 10,000 m3/hr * 1000 mg/m3 * 1 g/1000 mg * 1 kg/1000 g = 10 kg/hr

HCl flow rate = 10,000 m3/hr * 300 mg/m3 * 1 g/1000 mg * 1 kg/1000 g = 3 kg/hr

HF flow rate = 10,000 m3/hr * 100 mg/m3 * 1 g/1000 mg * 1 kg/1000 g = 1 kg/hr

Next, we calculate the moles of each pollutant using their molecular weights:

Moles of SO2 = 10 kg/hr / 64 kg/kmol = 0.15625 kmol/hr

Moles of HCl = 3 kg/hr / 36.5 kg/kmol = 0.08219 kmol/hr

Moles of HF = 1 kg/hr / 20 kg/kmol = 0.05 kmol/hr

The stoichiometric ratio for CaCO3 is 1.2, which means 1.2 moles of CaCO3 react with 1 mole of each pollutant. Therefore, the total moles of CaCO3 required can be calculated as follows:

Total moles of CaCO3 = 1.2 * (moles of SO2 + moles of HCl + moles of HF)

= 1.2 * (0.15625 + 0.08219 + 0.05) kmol/hr

= 0.375 kmol/hr

Finally, we convert the moles of CaCO3 to kg/day and tons/day:

Total CaCO3 dosage = 0.375 kmol/hr * 100 kg/kmol * 24 hr/day = 900 kg/day

Total CaCO3 dosage in tons/day = 900 kg/day / 1000 kg/ton = 0.9 tons/day

Therefore, the required total limestone (CaCO3) dosage to reduce SO2, HCl, and HF emissions to the specified limits is 1,875 kg/day or 1.875 tons/day.

In this calculation, we determined the limestone dosage required to reduce the emissions of SO2, HCl, and HF in a power plant stack gas to meet regulatory limits. The first step was to convert the uncontrolled emissions from mg/m3 to kg/hr based on the stack gas flowrate.

Then, we calculated the moles of each pollutant using their molecular weights. Considering the stoichiometric ratio between CaCO3 and each pollutant, we determined the total moles of CaCO3 required. Finally, we converted the moles of CaCO3 to kg/day and tons/day to obtain the limestone dosage.

This calculation ensures compliance with the specified emission limits and helps mitigate the environmental impact of the power plant.

Learn more about emissions

brainly.com/question/33156294

#SPJ11

A) False. Cubical aggregates have higher shear resistance as compared to rounded aggregates. B) True. The ratio of length to thickness is considered in determining elongated aggregate.

In general, the shape of the aggregate affects the shear resistance of concrete. Cubical aggregates provide more resistance to shear as compared to rounded aggregates due to their angular shape and larger surface area.

Elongated aggregates are those that have a high length to thickness ratio. These aggregates are not desirable in concrete as they can create voids and spaces in the concrete and reduce its strength. To determine the elongation of an aggregate, its length is divided by its thickness. If this ratio exceeds a certain limit (typically 3 or 4), the aggregate is considered elongated and should be avoided in concrete.

To know more about ratio visit:

https://brainly.com/question/13419413

#SPJ11

Igneous and bedded sedimentary rocks weather in different ways. This is because bedded sedimentary rocks are formed through the deposition of sediment, which is a loose collection of small particles, and igneous rocks are formed from cooling lava.

The weathering process of these rocks can be understood in terms of the subsurface profile of these rocks.Subsurface profile of igneous rockWeathering profiles of igneous rocks depend on factors such as the type of rock, mineralogy, texture, and the environment. The weathering process of igneous rock is a result of the chemical and physical reactions between the rock and the environment.

There are two types of weathering: mechanical and chemical. Mechanical weathering occurs when the rock is broken down physically, while chemical weathering occurs when the rock is altered chemically by water, oxygen, or other agents.The subsurface profile of an igneous rock will show the effects of weathering on the rock. Weathering occurs in layers, with the top layer showing the most weathering.

The top layer of an igneous rock is usually the most weathered, with the underlying rock being less weathered. The depth of the weathered layer depends on the rate of weathering and the age of the rock. As the rock weathers, it becomes more porous and less dense, which can lead to instability.

Subsurface profile of bedded sedimentary rockWeathering profiles of bedded sedimentary rocks depend on factors such as the type of rock, mineralogy, texture, and the environment. The weathering process of bedded sedimentary rock is a result of the chemical and physical reactions between the rock and the environment.

There are two types of weathering: mechanical and chemical. Mechanical weathering occurs when the rock is broken down physically, while chemical weathering occurs when the rock is altered chemically by water, oxygen, or other agents.The subsurface profile of a bedded sedimentary rock will show the effects of weathering on the rock. Weathering occurs in layers, with the top layer showing the most weathering.

The top layer of a bedded sedimentary rock is usually the most weathered, with the underlying rock being less weathered. The depth of the weathered layer depends on the rate of weathering and the age of the rock. As the rock weathers, it becomes more porous and less dense, which can lead to instability.

bsurface profile of rocks provides valuable information about the weathering process and can help predict problems that may arise during deep foundation works. Weathering occurs in layers, with the top layer showing the most weathering. The depth of the weathered layer can be determined by drilling a hole into the rock and examining the core. The subsurface profile of rocks can also provide information about the stability of the rock, which is important for deep foundation works. If deep foundation works are carried out on a subsurface profile that is unstable, it can lead to serious problems such as foundation settlement, slope instability, and landslides.

To know more about Mechanical weathering visit:

brainly.com/question/29616569

#SPJ11

tangent plane  z = (1/e² - (1/1 - 2e^(-e))(x - e) - ln(e)(y - 1))

(a) To find the directional derivative of f(x, y) in the direction of the vector (2, 3) at the point (e, 1), we can use the gradient operator. The gradient of f(x, y) is given by:

∇f(x, y) = (∂f/∂x, ∂f/∂y) = (y/x - 2xe^(-x), ln(x))

To find the directional derivative in the direction of (2, 3), we normalize the vector to get the unit vector:

u = (2/√(2^2 + 3^2), 3/√(2^2 + 3^2)) = (2/√13, 3/√13)

Now, we take the dot product of the gradient with the unit vector:

Def = ∇f(e, 1) ⋅ u

    = ((1/1 - 2e^(-e)), ln(e)) ⋅ (2/√13, 3/√13)

    = (2/√13 - 2e^(-e)/√13 + 3ln(e)/√13)

(b) To find the equation of the tangent plane to the graph of f(x, y) at the point (e, 1, 1/e²), we can use the formula for the equation of a plane:

z - z₀ = ∇f(x₀, y₀) ⋅ (x - x₀, y - y₀)

Plugging in the values (e, 1, 1/e²) for (x₀, y₀, z₀), and the corresponding values for ∇f(e, 1):

z - 1/e² = ((1/1 - 2e^(-e)), ln(e)) ⋅ (x - e, y - 1)

Simplifying, we get the equation of the tangent plane as:

z = (1/e² - (1/1 - 2e^(-e))(x - e) - ln(e)(y - 1))

This equation represents the tangent plane to the graph of f(x, y) at the point (e, 1, 1/e²).

learn more about tangent plane

brainly.com/question/31433124

#SPJ11

The second ionization energy of a helium atom is [tex]8.716 * 10^-18 J[/tex] and the wavelength of the photon emitted is [tex]7.239 * 10^-8 m.[/tex]

The Rydberg equation is suitable for hydrogen-like atoms with a proton nuclear charge and a single electron. It is given as follows:

[tex]\(\frac{1}{\lambda} = RZ^2 \left(\frac{1}{n_1^2} - \frac{1}{n_2^2}\right)\)[/tex]

where:

[tex]\(\lambda\)[/tex]is the wavelength of the photon

R is the Rydberg constant

Z is the atomic number of the element

[tex]\(n_1\)[/tex]is the initial energy level

[tex]\(n_2\)[/tex] is the final energy level

Using this equation and the given first ionization energy of a hydrogen atom, we can calculate the Rydberg constant (R). The first ionization energy of hydrogen (H) is 13.527 eV. We can convert this to joules (J) using the conversion factor 1 eV = [tex]1.602 x 10^-19 J.[/tex] So:

[tex]\(E = 13.527 \text{ eV} \times \frac{1.602 \times 10^{-19} \text{ J}}{1 \text{ eV}} = 2.179 \times 10^{-18} \text{ J}\)[/tex]

We can use this energy to calculate R:

[tex]\(\frac{1}{\lambda} = RZ^2 \left(\frac{1}{n_1^2} - \frac{1}{n_2^2}\right)\)\(R =\\ \frac{E}{Z^2 \left(\frac{1}{n_1^2} - \frac{1}{n_2^2}\right)} = \\\frac{2.179 \times 10^{-18} \text{ J}}{1^2 \left(\frac{1}{1^2} - \frac{1}{\infty^2}\right)} = 2.179 \times 10^{-18} \text{ J}\)[/tex]

Now we can use this value of R to calculate the second ionization energy of a helium (He) atom. Helium has an atomic number of 2, so Z = 2. We need to calculate the energy required to remove the second electron from a helium atom, so[tex]\(n_1 = 1\)[/tex](since the first electron has already been removed) and [tex]\(n_2 = \infty\)[/tex](since the electron is being removed from the atom completely). Plugging these values into the equation gives:

[tex]\(\frac{1}{\lambda} = RZ^2 \left(\frac{1}{n_1^2} - \frac{1}{n_2^2}\right)\)\(\frac{1}{\lambda} =\\ (2.179 \times 10^{-18} \text{ J}) \times (2^2) \left(\frac{1}{1^2} - \frac{1}{\infty^2}\right)\)\(\frac{1}{\lambda} =\\ (2.179 \times 10^{-18} \text{ J}) \times 4 \left(1 - 0\right)\)\(\frac{1}{\lambda} = \\8.716 \times 10^{-18} \text{ J}\)[/tex]

[tex]\(\lambda = \frac{hc}{E} = \frac{(6.626 \times 10^{-34} \text{ J s}) \times (3 \times 10^8 \text{ m/s})}{8.716 \times 10^{-18} \text{ J}} = 7.239 \times 10^{-8} \text{ m}\)[/tex]

Therefore, the second ionization energy of a helium atom is [tex]8.716 * 10^-18 J[/tex] and the wavelength of the photon emitted is[tex]7.239 * 10^-8 m.[/tex]

Know more about Rydberg equation

https://brainly.com/question/32679031

#SPJ11

The second ionization energy of a helium atom is 0 eV, meaning that it does not require any additional energy to remove the second electron since the atom is already fully ionized.

The Rydberg equation can be used to calculate the ionization energy of hydrogen-like atoms. The second ionization energy refers to the energy required to remove the second electron from an atom.

To calculate the second ionization energy of a helium atom, we can start by considering the electron configuration of helium. Helium has two electrons in total, so the first ionization energy refers to the energy required to remove one of these electrons.

Given that the first ionization energy of a hydrogen atom is 13.527 eV, we can use this information to calculate the first ionization energy of helium. Since helium has two electrons, the total ionization energy required to remove both electrons is twice the ionization energy of hydrogen.

First ionization energy of helium = 2 * (first ionization energy of hydrogen)
First ionization energy of helium = 2 * 13.527 eV
First ionization energy of helium = 27.054 eV

Now, let's move on to calculating the second ionization energy of helium. Since the first electron has already been removed, the second ionization energy refers to the energy required to remove the remaining electron.

To calculate the second ionization energy of helium, we need to subtract the first ionization energy from the total energy required to remove both electrons.

Second ionization energy of helium = Total ionization energy - First ionization energy
Second ionization energy of helium = (2 * 13.527 eV) - 27.054 eV
Second ionization energy of helium = 27.054 eV - 27.054 eV
Second ionization energy of helium = 0 eV

Therefore, the second ionization energy of a helium atom is 0 eV, meaning that it does not require any additional energy to remove the second electron since the atom is already fully ionized.

Know more about Rydberg equation

https://brainly.com/question/32679031

#SPJ11

The design features intended to improve access to public transport for people with mobility impairments are:

E. A, B, and C

These include:

A. Tactile Ground Surface Indicators (TGSI): These are textured surfaces on the ground that provide tactile cues to assist individuals with visual impairments in navigating their way to and within public transport stations.

B. Ramps and/or lifts to station platforms: These features provide accessibility for individuals using wheelchairs or other mobility devices by eliminating barriers such as stairs and providing a smooth transition between the platform and the vehicle.

C. "Kneeling buses" that allow for level bus boarding: Kneeling buses have the ability to lower the vehicle closer to curb level, making it easier for individuals with mobility impairments to board and disembark from buses.

These design features aim to create inclusive and accessible public transportation systems, ensuring that individuals with mobility impairments can independently and safely use public transport services.

To know more about surfaces visit:

brainly.com/question/33429527

#SPJ11

The conclusion "(x)(A(x) ∨ B(x))" is false since there exist elements (e.g., 1) that satisfy B(x) but not A(x).

To show that the argument is invalid using the model universe method, we need to find a counterexample where the premises are true, but the conclusion is false.

Let's consider the following interpretation:

Domain of discourse: {1, 2}

A(x): x is even

B(x): x is odd

Under this interpretation, the premises "(x)(A(x) ∧ B(x))" and "(∃x)A(x)" are true because all elements in the domain satisfy A(x) ∧ B(x), and there exists at least one element (e.g., 2) that satisfies A(x).

However, the conclusion "(x)(A(x) ∨ B(x))" is false since there exist elements (e.g., 1) that satisfy B(x) but not A(x).

In this counterexample, the premises are true, but the conclusion is false, demonstrating that the argument is invalid using the model universe method.

Learn more about domain here:

https://brainly.com/question/28135761

#SPJ11

The transfer function for a closed-loop control system is shown below. Because Km=1, the transfer function can be expressed as GcGvGp =KcGcGvGp= Kc/(ts+1).

Now, using the above formula, the offset of a set point change of 1 with the approximate transfer function GvGpGm = K/(ts+1) and Km = 1 in a close loop with a proportional controller with gain Kc is 1 – KKc/(1+KKc).

The transfer function for a closed-loop control system is shown below. Because Km=1, the transfer function can be expressed as GcGvGp =KcGcGvGp= Kc/(ts+1)

.We can apply a step change to the setpoint to see how well the closed-loop system is functioning. Assume that a step change in the setpoint from 0 to 1 is introduced into the system.

The input to the closed-loop system is the step change, and the output is the response to the step change. Since the closed-loop system is in equilibrium, the controller output is given by Yp = Ysp = 1.

The response of the system to the step change is shown in the following diagram.In steady-state, the response of the closed-loop system to the step change is given by the formula below, where Kc is the controller gain, and KKc is the product of the transfer function and the controller gain.

Ksp = GcGvGpGm/(1+GcGvGpGm) × Ysp

= Kc/(ts+1) /(1+Kc/(ts+1)) × 1

= Kc/(Kc+ts+1)

Therefore, the steady-state offset of the closed-loop system can be calculated as follows:

Δ = Ksp – Ysp

= Kc/(Kc+ts+1) – 1

= - ts/(Kc+ts+1)

Thus, the steady-state offset of the closed-loop system is -ts/(Kc+ts+1).Using the above formula, the offset of a set point change of 1 with the approximate transfer function GvGpGm = K/(ts+1) and Km = 1 in a close loop with a proportional controller with gain Kc is 1 – KKc/(1+KKc). The correct answer is option (c) 1 – KKc/(1+KKc).

To know more about equilibrium visit:

brainly.com/question/30694482

#SPJ11

It is given that PG grading requirement is met if the values of S(t) are between -3.2 and +3.2. As all the calculated values of S(t) lie within this range, the asphalt meets PG grading requirement.

Given data: Bending rheometer: 0.4mm, 0.5mm, 0.65mm, 0.82mm, 0.98mm, and 1.3mm for t = 15s, 30s, 45s, 60s, 75s, and 90s.

We are supposed to calculate the values of S(t) and m to check if the asphalt meets PG grading requirement.

Calculation of m:

Mean wheel track rut depth = (0.4+0.5+0.65+0.82+0.98+1.3)/6

= 0.7933mm

Calculation of S(t)

S(t) = (x - m)/0.3

Where, x = 0.4mm, 0.5mm, 0.65mm, 0.82mm, 0.98mm, and 1.3mm

Given, m = 0.7933mm

Substituting these values into the formula above:

S(15s) = (0.4 - 0.7933)/0.3

= -1.311S(30s)

= (0.5 - 0.7933)/0.3

= -0.9777S(45s)

= (0.65 - 0.7933)/0.3

= -0.4777S(60s)

= (0.82 - 0.7933)/0.3

= 0.128S(75s)

= (0.98 - 0.7933)/0.3

= 0.62S(90s)

= (1.3 - 0.7933)/0.3

= 1.521

It is given that PG grading requirement is met if the values of S(t) are between -3.2 and +3.2. As all the calculated values of S(t) lie within this range, the asphalt meets PG grading requirement.

To know more about range visit

https://brainly.com/question/29463327

#SPJ11