(I) The heat transfer coefficient, = 0.033
Heat balance = 20.66
(II) Temperature of cooling water at the outlet: = 29.82°C.
(III) Heat transfer rate: 28.8 MW.
How to sol;ve for the valuesE = 1 - exp(-NTU)
= [tex]1 - e^{0.0335}[/tex]
= 0.033
Heat balance
[tex]\frac{t_{2} -20 }{40-20}=0.033[/tex]
20.66
The heat transfer
= 700 x 4.18 x 1000 x (20.66 - 20)
= 1931.16 kW
The mass flow of steam
= 1931.16 kW / 2406
= 0.80 kg / s
(II) Temperature of cooling water at the outlet:
= 20 + 0.491 * (40 - 20)
= 29.82°C.
(III) Heat transfer rate:
= 700 * 4180 * (29.82 - 20)
= 2.88 * 10⁷ W
= 28.8 MW.
Read more on mass flow rate here https://brainly.com/question/31070366
#SPJ4
Calculate the perimeter of this right-angled triangle.
Give your answer in metres (m) to 1 d.p.
7m
19 m
Answer:
The perimeter is 37.4 meters.
Step-by-step explanation:
Here's the plan:
use Pythagorean Theorem to calculate the unmarked side, then add up all three sides.
First, use Pythagorean Theorem.
7^2 + x^2 = 16^2
49 + x^2 = 256
subtract 49
x^2 = 207
square root both sides.
x = 14.3874945699
Add up all three sides, because the perimeter is the distance all the way around the outside of the shape.
Perimeter =
14.387494 + 7 + 16
= 37.387494
round to the nearest tenth (one d.p. means one decimal place)
Perimeter = 37.4
The perimeter is 37.4 meters.
3. What is the diameter change of a 50-ft spherical tank made of ½" steel plate due to internal pressure of 100 psi? Assume that the tank may be considered as "thin-walled" and that the steel remains elastic and has the properties Elastic modulus Poisson's ratio Internal pressure Thickness steel Diameter = = 11 30,000,000 psi 0.3 100 psi ½" 50 ft
The diameter change of the 50-ft spherical tank due to internal pressure of 100 psi is approximately 0.0214 inches.
To calculate the diameter change of the spherical tank, we can use the formula for the change in diameter due to internal pressure in a thin-walled sphere:
ΔD = (4 * E * ΔP * D) / (3 * (1 - ν^2) * t)
where:
ΔD is the change in diameter
E is the elastic modulus of the steel (30,000,000 psi)
ΔP is the internal pressure (100 psi)
D is the original diameter of the tank (50 ft)
ν is the Poisson's ratio of the steel (0.3)
t is the thickness of the steel plate (0.5 inches)
Plugging in the given values into the formula, we have:
ΔD = (4 * 30,000,000 * 100 * 50) / (3 * (1 - 0.3^2) * 0.5)
Simplifying the equation, we get:
ΔD = 0.0214 inches
Therefore, the diameter change of the 50-ft spherical tank due to the internal pressure of 100 psi is approximately 0.0214 inches.
Learn more about diameter
brainly.com/question/32968193
#SPJ11
A school purchased sand to fill a sandbox on its playground. The dimensions of the sandbox in meters and the total cost of the sand in dollars are known. Which units would be most appropriate to describe the cost of the sand?
The most appropriate units to describe the cost of the sandbox would indeed be dollars.
When describing the cost of an item or service, it is essential to use the unit that represents the currency being used for the transaction. In this case, the total cost of the sand for the school's sandbox is given in dollars. To maintain consistency and clarity, it is best to express the cost in the same unit it was provided.
Using dollars as the unit for the cost allows for clear communication and understanding among individuals involved in the transaction or discussion. Dollars are widely recognized as the standard unit of currency in many countries, including the United States, where the dollar sign ($) is commonly used to denote monetary values.
Using meters, the unit for measuring the dimensions of the sandbox, to describe the cost would be inappropriate and could lead to confusion or misunderstandings. Mixing units can cause ambiguity and hinder effective communication.
Therefore, it is most appropriate to describe the cost of the sand in dollars, aligning with the unit of currency provided and commonly used in financial transactions. This ensures clarity and facilitates accurate comprehension of the cost associated with the sand purchase for the school's sandbox.
for similar questions on sandbox.
https://brainly.com/question/31290675
#SPJ8
Create a word problem with a topic Matheson Formula and
Double Decllining Balance
Show your solution and provide
illustrations/diagrams
One method of calculating depreciation is known as the double-declining balance method. In this technique, an asset's value is decreased by twice the straight-line depreciation rate in the initial year.
Let's consider an example to understand the calculation with the help of Matheson Formula.Ms. Lee has a photocopier that cost her $10,000. She wants to keep the machine for five years before selling it. Calculate the depreciation for each year by using the double-declining balance method. If the Matheson Formula is applied for the first year. Assuming that the machine has no salvage value at the end of its useful life.
Using the Matheson formula:
Depreciation rate = 1 - (salvage value / cost of asset) ^ (1/ useful life)
Depreciation rate = 1 - (0 / 10,000) ^ (1/5)
Depreciation rate = 1 - (0)
Depreciation rate = 1
Depreciation for the first year = Depreciation rate * 2 * straight-line depreciation percentage
Depreciation percentage for straight-line = 100% / useful life
Depreciation percentage for straight-line = 100% / 5
Depreciation percentage for straight-line = 20%
Depreciation for the first year = 1 * 2 * 20%
Depreciation for the first year = 40% * $10,000
Depreciation for the first year = $4,000
After the first year, we must compute the remaining asset's value.
The asset's worth is decreased by 40% for the first year ($4,000) and has a remaining value of $6,000.
As a result, we can use the same method to calculate the next year's depreciation. We multiply the remaining value of $6,000 by 40% to get a $2,400 depreciation in the second year, leaving us with $3,600 of the asset's worth to be depreciated in the following year.
This technique is repeated for the remainder of the asset's useful life until the scrap value is reached or until the end of the asset's useful life.
The word problem with a topic Matheson Formula and double declining balance and solution is provided and also provided illustrations /diagrams
Word Problem: Let's consider a scenario where a company purchases a delivery truck for $40,000. The truck has a useful life of 8 years and a salvage value of $5,000. The company decides to use the Matheson Formula and Double Declining Balance method to calculate the depreciation expense each year.
Solution:
Step 1: Determine the depreciable cost of the truck.
The depreciable cost is the initial cost minus the salvage value.
Depreciable cost = $40,000 - $5,000
= $35,000.
Step 2: Calculate the annual depreciation rate.
The annual depreciation rate using the Double Declining Balance method is twice the straight-line rate.
Straight-line rate = 1 / Useful life
= 1 / 8
= 0.125
Double Declining Balance rate = 2 * 0.125
= 0.25 or 25%.
Step 3: Calculate the annual depreciation expense for each year.
Year 1: Depreciation expense = Depreciable cost * Depreciation rate
= $35,000 * 25%
= $8,750.
Year 2: Depreciation expense
= (Depreciable cost - Year 1 depreciation) * Depreciation rate
= ($35,000 - $8,750) * 25%
= $6,562.50.
Year 3: Depreciation expense = (Depreciable cost - Year 1 depreciation - Year 2 depreciation) * Depreciation rate
= ($35,000 - $8,750 - $6,562.50) * 25%
= $4,921.88.
And so on for the remaining years.
Illustration:
Here is a diagram illustrating the depreciation expense for each year using the Double Declining Balance method:
Year 1: $8,750Year 2: $6,562.50Year 3: $4,921.88Year 4: $3,691.41Year 5: $2,768.56Year 6: $2,076.42Year 7: $1,557.31Year 8: $1,167.98By following the steps and calculations explained above, we can determine the annual depreciation expense using the Matheson Formula and Double Declining Balance method for the given scenario.
Learn more about depreciation methods here:
https://brainly.com/question/27971176
#SPJ4
What is the volume of this cylinder?
Use ≈ 3.14 and round your answer to the nearest hundredth.
The top of the cylinder is 14 meters
The side of the cylinder is 9 meters.
Give the answer in cubic meters and round to the nearest hundredth.
Answer:
1384.74
Step-by-step explanation:
The formula for finding volume is πr²h
π = 3.14
Diameter is 14 m. But r stands for radius.
Radius is 1/2 of diameter
Therefore; radius is 1/2 of 14 = 7
r = 7
Side of cylinder is equal to height(h)
Therefore h is 9m.
V = πr²h
V= 3.14 x7²x9
V=1384.74 meters.
A proposed mechanism for the decomposition of N₂O is given below: Which species is the catalyst? NO + N₂O-> N₂ + NO₂ 10₂ NO₂ -> NO + O NO ON₂ O NO₂ ON₂0 Page 7 of 35 Activate Windows 841 PM.
A proposed mechanism for the decomposition of N₂O is given below: NO + N₂O -> N₂ + NO₂10₂ NO₂ -> NO + O NO ON₂ O NO₂ ON₂0
The species that acts as a catalyst in the proposed mechanism for the decomposition of N₂O is NO. NO is the catalyst in this reaction.
The proposed mechanism for the decomposition of N₂O can be explained as follows:
Step 1: N₂O is oxidized by NO to form N₂ and
NO₂.NO + N₂O → N₂ + NO₂
Step 2: The NO₂ produced in step 1 is broken down to NO and O.10₂
NO₂ → NO + O NO
Step 3: The O produced in step 2 reacts with N₂ to form NO and N₂O. ON₂ O + NO → NO₂ + N₂O
Step 4: In step 3, N₂O is recycled and goes back to step 1.
NO is the catalyst in this reaction because it is consumed in step 2 but produced again in step 3, allowing the reaction to continue.
For more information on catalyst visit:
brainly.com/question/24430084
#SPJ11
In the proposed mechanism for the decomposition of N₂O, NO acts as the catalyst by facilitating the reaction between N₂O and N₂, and it is regenerated in the process.
The proposed mechanism for the decomposition of N₂O is given as follows:
1. NO + N₂O -> N₂ + NO₂
2. 10₂ NO₂ -> NO + O
3. NO + N₂O -> N₂ + NO₂
In this mechanism, the species that acts as the catalyst is NO. A catalyst is a substance that speeds up a chemical reaction without being consumed in the process. It lowers the activation energy required for the reaction to occur, allowing the reaction to proceed at a faster rate.
In the given mechanism, NO appears in the first and third steps. It reacts with N₂O to form N₂ and NO₂, and then it is regenerated in the third step by reacting with N₂O again. This shows that NO is not consumed in the overall reaction and plays a role in facilitating the reaction between N₂O and N₂.
Learn more about decomposition
https://brainly.com/question/14843689
#SPJ11
A steel that has 0.151% C is subjected to a carburizing treatment. Under operating conditions, the carbon content on the surface reaches 1.1% C. The temperature at which the process is carried out is 996 °C, where the material is FCC, (D0 = 0.23 cm2/s, Q = 32900 Cal/mol°K, R =1.987 cal/mol).
Estimate the carbon content at a depth of 57 microns from the surface, (1mm=1000 microns), after 7 hours of treatment.
Suppose that the function erf(Z) can be approximately evaluated by the following equation: erf (2) = -0.3965Z2 + 1.24952 -0.0063
The estimated carbon content at a depth of 57 microns from the surface after 7 hours of treatment is approximately 0.00436949 or 0.437% C.
To estimate the carbon content at a depth of 57 microns from the surface after 7 hours of carburizing treatment, we can use the diffusion equation.
The diffusion equation is given by:
C = Co + (Cs - Co) * [1 - erf((D * t)/(2 * sqrt(Q * t)))]
Where:
C = Carbon content at a certain depth after a given time
Co = Initial carbon content
Cs = Carbon content on the surface
D = Diffusion coefficient
t = Time
Given:
Initial carbon content (Co) = 0.151% = 0.00151
Carbon content on the surface (Cs) = 1.1% = 0.011
Diffusion coefficient (D) = D0 * exp(-Q/RT)
D0 = 0.23 cm^2/s
Q = 32900 Cal/mol*K
R = 1.987 cal/mol*K
T = 996 °C = 996 + 273 = 1269 K
We can calculate the diffusion coefficient (D):
D = D0 * exp(-Q/RT)
D = 0.23 * exp(-32900/(1.987 * 1269))
D ≈ 0.23 * exp(-25.897)
D ≈ 0.23 * 2.748e-12
D ≈ 6.317e-13 cm^2/s
Now, let's calculate the carbon content at a depth of 57 microns (0.057 mm) after 7 hours (t = 7 * 3600 seconds):
C = 0.00151 + (0.011 - 0.00151) * [1 - erf((6.317e-13 * (7 * 3600))/(2 * sqrt(32900 * (7 * 3600))))]
Using the given approximation equation:
erf(2) = -0.3965Z^2 + 1.24952 - 0.0063
Substituting the values:
erf((6.317e-13 * (7 * 3600))/(2 * sqrt(32900 * (7 * 3600)))) = -0.3965 * ((6.317e-13 * (7 * 3600))/(2 * sqrt(32900 * (7 * 3600))))^2 + 1.24952 - 0.0063
Simplifying the equation:
erf((6.317e-13 * (7 * 3600))/(2 * sqrt(32900 * (7 * 3600)))) ≈ 0.699
Substituting this value back into the diffusion equation:
C ≈ 0.00151 + (0.011 - 0.00151) * [1 - 0.699]
C ≈ 0.00151 + (0.011 - 0.00151) * 0.301
C ≈ 0.00151 + 0.00949 * 0.301
C ≈ 0.00151 + 0.00285949
C ≈ 0.00436949
Therefore, the estimated carbon content at a depth of 57 microns from the surface after 7 hours of treatment is approximately 0.00436949 or 0.437% C.
Know more about estimated carbon here:
https://brainly.com/question/24233481
#SPJ11
Construct a proof for the following argument.
~(∃x)(Ax • Bx)
~((x)(Bx ⊃ Cx)
(x) ((~Ax • Dx) ⊃ ~Bx)
/Δ ~(x) (Bx ⊃ Dx)
The argument to be proven is Δ: ~(x)(Bx ⊃ Dx). This can be demonstrated using a proof by contradiction, assuming the negation of Δ and deriving a contradiction.
To prove Δ: ~(x)(Bx ⊃ Dx), we will use a proof by contradiction. We assume the negation of Δ, which is ((x)(Bx ⊃ Dx)). By double negation, this can be simplified to (x)(Bx ⊃ Dx).
Next, we will introduce a new assumption, let's call it γ, which states (∃x)(Bx • ~Dx). We will aim to derive a contradiction from this assumption.
By using the existential elimination (∃E) rule, we can introduce a specific variable, say c, such that (Bc • ~Dc) holds.
Now, we can apply the universal elimination (∀E) rule to the assumption (x)(Bx ⊃ Dx) using the variable c, which gives us Bc ⊃ Dc.
Using modus ponens, we can combine Bc ⊃ Dc with Bc • ~Dc to derive a contradiction, which negates the assumption γ.
Having derived a contradiction, we can conclude that the negation of Δ: ~(x)(Bx ⊃ Dx) is true, leading to the validity of Δ itself: ~(x)(Bx ⊃ Dx).
Learn more about Contradiction proof: brainly.com/question/30459584
#SPJ11
The argument to be proven is Δ: ~(x)(Bx ⊃ Dx). This can be demonstrated using a proof by contradiction, assuming the negation of Δ and deriving a contradiction.
To prove Δ: ~(x)(Bx ⊃ Dx), we will use a proof by contradiction. We assume the negation of Δ, which is ((x)(Bx ⊃ Dx)). By double negation, this can be simplified to (x)(Bx ⊃ Dx).
Next, we will introduce a new assumption, let's call it γ, which states (∃x)(Bx • ~Dx). We will aim to derive a contradiction from this assumption.
By using the existential elimination (∃E) rule, we can introduce a specific variable, say c, such that (Bc • ~Dc) holds.
Now, we can apply the universal elimination (∀E) rule to the assumption (x)(Bx ⊃ Dx) using the variable c, which gives us Bc ⊃ Dc.
Using modus ponens, we can combine Bc ⊃ Dc with Bc • ~Dc to derive a contradiction, which negates the assumption γ.
Having derived a contradiction, we can conclude that the negation of Δ: ~(x)(Bx ⊃ Dx) is true, leading to the validity of Δ itself: ~(x)(Bx ⊃ Dx).
Learn more about Contradiction proof: brainly.com/question/30459584
#SPJ11
In the Lewis structure of the iodite ion,
IO2-, that satisfies the
octet rule, the formal charge on the central iodine atom is:
The formal charge on the central iodine atom in the Lewis structure of the iodite ion (IO₂⁻) that satisfies the octet rule is 0.
Formal charge can be defined as the electric charge on an atom if the electrons were distributed equally between the atoms in a compound. It can be calculated using the following formula:
FC = Valence electrons - Lone pair electrons - 1/2 Bonding electrons
In the Lewis structure of IO₂⁻, there are two oxygen atoms that each contain six valence electrons, and the central iodine atom has seven valence electrons. There are two single bonds between each oxygen atom and the central iodine atom, which account for four bonding electrons.
In the Lewis structure, there are also two lone pairs of electrons around each oxygen atom. Thus, by using the above formula, we can calculate the formal charge of the central iodine atom.
FC = 7 valence electrons - 0 lone pair electrons - 1/2 (4 bonding electrons)
FC = 7 - 0 - 2 = 5.
Thus, the formal charge on the central iodine atom is 0 since it owns the same number of valence electrons that it has in an isolated atom.
Learn more about formal charge here:
https://brainly.com/question/30459289
#SPJ11
A stack 130 m tall (physical stack height) emits 910 g of pollutant per minute. It is a clear night. The wind speed measured at a height of 10 m is 3.1 m/sec. Plume rise is 50 m. Estimate the pollutant concentration at ground-level at a distance of 800 m downwind, 80 m away from the centerline. Terrain is urban. Provide the answer in ug/m3. Please show all calculations
Physical Stack height = 130m Pollutant emitted per minute = 910 gWind Speed at height of 10m = 3.1 m/sec Plume rise = 50m Distance downwind (x) = 800m Distance away from centerline (y)
= 80mFormula used to calculate pollutant concentration is C = Q/(2πw * u * h) * e ^[-y * (1 + h/w)]
Effective stack width (W) = (1.57 * h) + (0.5 * Wp)
= 195mW
= (1.57 * 130) + (0.5 * 195)
= 301.55
= 11.84 m/s
Exponent = -y * (1 + h/w)
= -80 * (1 + 130/301.55)
= -58.32 Finally, calculate the concentration using the formula mentioned above.μg/m³C = Q/(2πw * u * h) * e^[Exponent] = 15.16/(2 * 3.14 * 301.55 * 11.84 * 130) * e^-58.32
= 0.200 μg/m³ (approx) Hence, the answer is 0.200 μg/m³
To know more about Distance , visit:
https://brainly.com/question/32043377
#SPJ11
The pollutant concentration at ground-level at a distance of 800 m downwind, 80 m away from the centerline is 0.200 μg/m³
Physical Stack height = 130m
Pollutant emitted per minute = 910 g
Wind Speed at height of 10m = 3.1 m/sec
Plume rise = 50m
Distance downwind (x) = 800m
Distance away from centerline (y)
= 80m
Formula used to calculate pollutant concentration is
C = Q/(2πw * u * h) * e ^[-y * (1 + h/w)]
Effective stack width (W) = (1.57 * h) + (0.5 * Wp)
= 195mW
= (1.57 * 130) + (0.5 * 195)
= 301.55
= 11.84 m/s
Exponent = -y * (1 + h/w)
= -80 * (1 + 130/301.55)
= -58.32
Finally, calculate the concentration using the formula mentioned above.
μg/m³C = Q/(2πw * u * h) * e^[Exponent]
= 15.16/(2 * 3.14 * 301.55 * 11.84 * 130) * e^-58.32
= 0.200 μg/m³ (approx)
Hence, the answer is 0.200 μg/m³
To know more about Distance , visit:
brainly.com/question/32043377
#SPJ11
A large block of aluminium is loaded to a stress of 405 MPa. If the fracture toughness KIc is 39 MPa√m, determine
(i) the critical length of a crack at 35° angle and
(ii) the critical radius of a buried penny-shaped crack
i). The critical length of a crack at 35° angle is approximately equal to 312m.
ii). The critical radius of a buried penny-shaped crack is approximately equal to 3.3m.
Given data:
Stress (σ) = 405 MPa
Fracture toughness (KIC) = 39 MPa √m
Crack angle (θ) = 35°
(i) The critical length of a crack at 35° angle
From the formula,
we know that the critical crack length is given by:
KIc = σ √(πa) × f (θ) …… (1)
where f (θ) is a geometry factor,
which is a function of the crack angle (θ).
Assuming f (θ) = 1.12 (for 35° angle)
KIc = 39 MPa √mσ
= 405 MPa
Putting these values in equation (1),
39 × 10⁶
= 405 × √(πa) × 1.1239 × 10⁶/(405 × 1.12) = √(πa)
31284.82 = √(πa)
πa = (31284.82)²
πa = 980,870,794.19
a = 311.99 m≈ 312m
Therefore, the critical length of a crack at 35° angle is approximately equal to 312m.
(ii) The critical radius of a buried penny-shaped crack
From the formula, we know that the critical radius is given by:
KIc = (2σ)²/(πa)
KIc = 39 MPa √mσ
= 405 MPa
Putting these values in the above equation,
39 × 10⁶ = (2 × 405)²/πa39 × 10⁶
= (2 × 405)²/πr²
(πr²) = (2 × 405)²/39 × 10⁶
πr² = 33.264
r² = 33.264/π
r² = 10.59
r = √10.59
r = 3.26 m≈ 3.3m
Therefore, the critical radius of a buried penny-shaped crack is approximately equal to 3.3m.
To know more about critical radius, visit:
https://brainly.com/question/33176751
#SPJ11
What is the % dissociation of an acid, HA 0.10 M, if
the solution has a pH = 3.50? a) 0.0032 b) 35 C) 0.32 d) 5.0 e) 2.9
The percentage dissociation of an acid HA 0.10 M, when the solution has a pH = 3.50 is 2.9%.Option (e) 2.9 is correct.
According to the Arrhenius concept, an acid is a compound that releases H+ ions in an aqueous solution. According to the Bronsted-Lowry theory, an acid is a substance that donates a proton. The equilibrium constant expression of an acid HA can be expressed as follows:
HA ⇌ H+ + A
Dissociation constant:
Ka = ([H+][A-])/[HA]pH = -log[H+]pH + pOH = 14[H+] = 10-pH
The dissociation of an acid can be calculated using the following formula:
α = ( [H+]/Ka + 1) × 100%Hence, the dissociation constant of an acid is calculated using the following formula:
Ka = [H+][A-]/[HA]
= (α2×[HA])/ (100-α)
α = ( [H+]/Ka + 1) × 100%10-pH/Ka
= ([H+][A-])/[HA]0.00406
= ([H+][A-])/[HA]
Let α be the percentage dissociation of the acid α, [H+]
= [A-], [HA]
= 0.10-α/100.
Hence,0.00406 = (α/100)2×0.10-α/100/ (1-α/100)On solving, α = 2.9%.
To know more about dissociation visit:-
https://brainly.com/question/32501023
#SPJ11
Which among the following statements is true? Every differential equation has at least one solution. A single differential equation can serve as a mathematical model for many different phenomena. Every differential equation has a unique solution. None of the mentioned
Every differential equation has a unique solution.
What is the nature of solutions for a given differential equation?Differential equations describe the relationships between a function and its derivatives. The nature of solutions for a given differential equation depends on the specific equation and its initial or boundary conditions.
The statement "Every differential equation has a unique solution" is true. According to the existence and uniqueness theorem for ordinary differential equations, if a differential equation is well-posed, meaning it satisfies certain conditions, then there exists a unique solution that satisfies the equation and the given initial or boundary conditions.
While it is true that a single differential equation can serve as a mathematical model for many different phenomena, this does not imply that every differential equation has multiple solutions. Each differential equation has its own set of solutions, and the uniqueness of these solutions is determined by the initial or boundary conditions imposed.
Learn more about: solution
brainly.com/question/1616939
#SPJ11
A refrigerator is powered by a 4.90-horsepower motor.
(1 hp=746 watts). You want to keep the inside of the fridge at
2.43◦C and the room temperature is 34.15◦C. determine the value
of qc to watts. Assume that ηr is 50% of the maximum value.
A refrigerator is powered by a 4.90- horse power motor. (1 hp=746 watts). You want to keep the inside of the fridge at 2.43◦C and the room temperature is 34.15◦C. determine the value of qc to watts. Assume that ηr is 50% of the maximum value
One horsepower is equal to 746 watts and the motor used is 4.90 horsepower. Room temperature is 34.15◦C, and fridge temperature should be maintained at 2.43◦C. Efficiency ηr is 50% of the maximum value. To determine the value of qc to watts, we can use the formula: qc = W/m. Where W = power consumed by the refrigerator and m = mass of the refrigerant. For air conditioning or refrigeration systems, the following formula can be used to calculate the required refrigeration capacity (W):W = Q / h we. Where Q = heat load or cooling capacity in watts,h we = enthalpy of the refrigerant flowing through the evaporator. T he heat load can be calculated as follows: Q = mc ΔtWhere m = mass of the refrigerant, c = specific heat of the refrigerant, Δt = temperature difference or degree of cooling required. Now, to calculate qc, we need to calculate W and m. Here, we are given the power consumed by the motor, which is 4.90 horsepower or 3653.4 watts. Since the efficiency ηr is 50% of the maximum value, the power consumed by the refrigerator would be half of the motor power, which is: W = (1/2) x 3653.4 = 1826.7 watts. To calculate the mass of the refrigerant, we can use the following formula: m = Q / (c Δt)Here, c = specific heat of air, which is approximately 1 kJ/kg °C, and Δt = (34.15 - 2.43) = 31.72°C. Substituting the values, we get: m = Q / (c Δt) = (1826.7) / (1 x 31.72) = 57.54 kg. Now that we have both W and m, we can calculate qc as follows: qc = W/m = 1826.7 / 57.54 = 31.73 watts/kg. Therefore, the value of qc to watts is 31.73 watts/kg.
In this question, we were required to calculate the value of qc to watts for a refrigerator powered by a 4.90-horsepower motor. We used the formulas for refrigeration capacity, heat load, and mass of the refrigerant to arrive at the answer. We found that the value of qc to watts is 31.73 watts/kg, which represents the cooling capacity of the refrigerator per unit mass of the refrigerant.
learn more about temperature visit:
brainly.com/question/7510619
#SPJ11
please tell which option and explain
If 27 % of an isotope's original activity remains after 4.0 years, what is the half-life of this isotope? 1.2 years 0.47 years 1.5 years 3.2 years 2.1 years
Rounding to the nearest significant digit, the half-life of this isotope is approximately 3.2 years. Therefore, the correct option is 3.2 years.
The remaining activity of an isotope after a certain period of time can be used to determine its half-life. In this case, if 27% of the original activity remains after 4.0 years, it means that the isotope has undergone one half-life. The formula for calculating the remaining activity after a certain number of half-lives is given by:
Remaining activity = (Initial activity) * (1/2)*(number of half-lives)
Since 27% is equivalent to 0.27, we can set up the equation as:
0.27 = (1/2)^(number of half-lives)
To solve for the number of half-lives, we take the logarithm of both sides:
log(0.27) = log((1/2)*(number of half-lives))
Using logarithm properties, we can bring down the exponent:
log(0.27) = (number of half-lives) * log(1/2)
Now we can solve for the number of half-lives:
number of half-lives = log(0.27) / log(1/2) ≈ 2.069
Since we are given that the time period is 4.0 years, and each half-life is equal to the half-life of the isotope, we can divide the total time by the number of half-lives:
Half-life ≈ 4.0 years / 2.069 ≈ 1.93 years
To know more about isotope,
https://brainly.com/question/1269618
#SPJ11
(a) Show that y= Ae²+ Be, where A and B are constants, is the general solution of the differential equation y"+y'-6y=0. Hence, find the solution when y(1)=2e²-e and y(0) = 1.
Consider the differential equation y'' + y' - 6y = 0. Let us assume the solution as y = e^(mx), where m is a constant. Differentiating the equation with respect to x, we get: [tex]y' = me^(mx),[/tex] [tex]y'' = m²e^(mx).[/tex]
Substituting these values into equation (1),
we get: [tex]m²e^(mx) + me^(mx) - 6e^(mx) = 0[/tex]
Simplifying further, we have:
[tex](m² + m - 6)e^(mx) = 0[/tex]
This equation can be factored as:
[tex](m + 3)(m - 2)e^(mx) = 0[/tex]
Setting each factor equal to zero, we find two possible values for m:
[tex]m = -3 and m = 2.[/tex]
The general solution of the differential equation [tex]y'' + y' - 6y = 0 is:y = Ae^(2x) + Be^(-3x) ...(2)[/tex]
where A and B are constants.
To find the solution when [tex]y(1) = 2e² - e and y(0) = 1[/tex], we substitute x = 1 into equation (2) and equate it to 2e² - e. We also substitute x = 0 into equation (2) and equate it to 1.
Solving these equations, we can determine the values of A and B.
Finally, substituting the values of A and B back into equation (2), we obtain the required solution:[tex]y = (7e^(2x) + 2e^(-3x))/5[/tex].
To know more about differential equation visit:
https://brainly.com/question/29657983
#SPJ11
It is necessary to determine the area of a basin (in m?) On a map with a scale of 1:10,000. The average reading in the Planimeter is 6.43 revolutions for the basin. To calibrate the planimeter, a rectangle is drawn with Dimensions of 5 cm×5 cm, it is traced with the planimeter and the reading in it is 0.568 revolutions.
we can use the average reading of 6.43 revolutions for the basin to calculate its area.
Area of basin = (Planimeter reading x K) / Map scal
Area of basin = (6.43 revolutions x 44.01 cm²/rev) / 10,000 cm²/m²
Area of basin = 0.0282 m²
Yes, it is necessary to determine the area of a basin on a map with a scale of 1:10,000. The scale 1:10,000 implies that one unit of measurement on the map is equal to 10,000 units of measurement in the real world.
Therefore, the area of the basin is 0.0282 square meters.
In order to determine the area of the basin in square meters, we need to use the reading from the planimeter.
First, we need to calibrate the planimeter. To do this, a rectangle with dimensions of 5 cm x 5 cm is drawn and traced with the planimeter. The reading in it is 0.568 revolutions. We can use this reading to determine the planimeter constant (K) as follows:
K = Area of calibration rectangle / Planimeter reading
[tex]K = (5 cm x 5 cm) / 0.568[/tex] revolutions
[tex]K = 44.01 cm²/rev[/tex]
Now
To know more about determine visit:
https://brainly.com/question/29898039
#SPJ11
The Ash and Moisture Free analysis of coal used as fuel in a power plant is as follows:
Sulfur = 3.24% Hydrogen = 6.21% Oxygen = 4.87%
Carbon = 83.51% Nitrogen = 2.17%
Calculate the Volume Flow Rate of the Wet Gas in m3/s considering a 15.4% excess air, the mass of coal is 8788 kg/hr, the Rwg = 0.2792 kJ/kg-K, the ambient pressure is 100 kPa, and the temperature of the Wet Gas is 303 0C.
Note: Use four (4) decimal places in your solution and answer.
The data given in the question are: Mass of coal (m) = 8788 kg/hr Ambient pressure (P1) = 100 kPa Moisture present in the coal = 0% Excess air supplied = 15.4% Oxygen (O) in flue gas = 4.87% Carbon dioxide (CO2) in flue gas = 15.25% Nitrogen (N2) in flue gas = 79.58%
The volume flow rate of the wet gas is given as, Q = V x ? Where, V = Volume of the wet gas, and ? = Density of the wet gas. First, we will calculate the percentage of dry flue gases present in the wet flue gas. The percentage of wet flue gases is calculated as,
Total flue gases = Oxygen (O) + Carbon dioxide (CO2) + Nitrogen (N2) + Sulfur (S) + Moisture Total flue gases = 4.87 + 15.25 + 79.58 + 3.24 + 0 = 103.94%
Dry flue gases = Total flue gases - Moisture Dry flue gases = 103.94 - 0 = 103.94%The percentage of excess air supplied is given as 15.4%. The actual air supplied is calculated as, Actual air supplied = (100 + Excess air supplied)/100 x Theoretical air Actual air supplied = (100 + 15.4)/100 x 6.21/2.67Actual air supplied = 3.4654 kg/kg of coal Theoretical air = 6.21/2.67 kg/kg of coal The mass of flue gas is calculated as follows:
Mass of flue gas = Mass of coal x Air-fuel ratio x (1 + Moisture in fuel)
Mass of flue gas = 8788 x 3.4654 x (1 + 0)
Mass of flue gas = 106780.57 kg/hr
The volume flow rate of the wet gas is calculated as follows: Q = V x ?V = Q / ?Where the density of the wet gas is given by,
? = 0.3568 [(P1 x Mw) / (Rwg x (Tg + 273.15))]
The molecular weight of flue gas (Mw) = 28.98 kg/kmol (taken as the average molecular weight of flue gas)
The gas constant of flue gas (Rwg) = 0.2792 kJ/kg-K
The temperature of flue gas (Tg) = 303 + 273.15 = 576.15 K
The density of the wet gas,
? = 0.3568 [(100 x 28.98) / (0.2792 x 576.15)]? = 2.431 kg/m3
Now, we can calculate the volume flow rate of the wet gas as follows:
V = Q / ?106780.57 / (2.431)
= 43967.53 m3/hrQ
= 12.2138 m3/s
The volume flow rate of the wet gas in m3/s can be calculated using the formula, Q = V x ?, where V is the volume of the wet gas and ? is the density of the wet gas. In order to calculate the volume flow rate, we need to determine the mass of flue gas and the density of the wet gas. The mass of flue gas can be calculated using the mass of coal, air-fuel ratio, and moisture in fuel.
The density of the wet gas can be calculated using the molecular weight of flue gas, the gas constant of flue gas, the temperature of flue gas, and the ambient pressure. Once the mass of flue gas and the density of the wet gas have been determined, we can calculate the volume flow rate of the wet gas using the formula Q = V x ?.
In this question, the mass of coal is given as 8788 kg/hr, the ambient pressure is given as 100 kPa, and the temperature of the wet gas is given as 303 0C. The excess air supplied is given as 15.4%, and the Rwg is given as 0.2792 kJ/kg-K.
The moisture present in the coal is given as 0%. Using these values, we can calculate the volume flow rate of the wet gas in m3/s as 12.2138 m3/s. Therefore, the answer is 12.2138 m3/s.
Thus, we can conclude that the volume flow rate of the wet gas in m3/s is 12.2138 m3/s.
To learn more about Ambient pressure visit:
brainly.com/question/33544108
#SPJ11
The specific gravity of the liquid passing through the 1 cm diameter pipe shown in the figure is (y) = 10 K/N3 and the dynamic viscosity (mu) is 3*10^-3Pa.s.
Calculate whether the liquid will be stationary, upstream or downstream, within the framework of the conservation of energy principles.
Also find the average velocity (V) of the liquid in the pipe.
I couldn't upload the shape unfortunately, but its features are as follows
elevation=0m , p=200 KpA elevation=10m p=110 kpA
The liquid will be flowing downstream in the pipe and the average velocity of the liquid in the pipe is 11.54 m/s.
As we know that the flow of the liquid is driven by the difference in pressure and it always flows from higher pressure to lower pressure.
The specific gravity of the liquid passing through the 1 cm diameter pipe is given as y = 10 kN/m³ and the dynamic viscosity is given as μ = 3 × 10⁻³ Pa·s.
Calculation:The pressure difference between the two points is given byΔp = 200 - 110 = 90 kPaNow, the Reynolds number can be calculated by using the formula below:Re = (ρVD)/μWhere;V is the velocity of the fluid,D is the diameter of the pipeρ is the density of the fluid.
The formula for Bernoulli's principle for incompressible fluids is given by:P1 + 1/2 ρV1^2 + ρgy1 = P2 + 1/2 ρV2^2 + ρgy2Let us consider the two points, one at the top and another at the bottom of the tube.
Let point 1 be at the top, and point 2 be at the bottomPoint 1: P1 = 200 kPa, V1 = 0, y1 = 0Point 2: P2 = 110 kPa, y2 = 10 m, V2 = ?.
Substitute the given values into Bernoulli's equation, we get:
P1 + 1/2ρV₁² + ρgy1 = P2 + 1/2ρV₂² + ρgy2.
By substituting the values given in the problem, we get:
200 × 103 + 1/2 × 10 × V₁² + 0 = 110 × 103 + 1/2 × 10 × V₂² + 10 × 10 × 10 × 10.
As V1 is equal to zero, we can solve the above equation for V2 and we get:
V2 = 11.54 m/sBy using the formula of Re, we get;Re = (ρVD)/μ,
Where;
V = 11.54 m/s,
D = 0.01 mμ,
0.01 mμ = 3 × 10⁻³ Pa.s,
ρ = 10 kN/m3
10 kN/m3 = 10000 kg/m3,
Re = (10000 × 11.54 × 0.01)/ (3 × 10^-3),
Re = 3.85 × 10⁵.
As the Reynolds number is greater than 4000, the flow is turbulent.As the Reynolds number is greater than 4000, the flow is turbulent.
Hence, the liquid will be flowing downstream in the pipe.As per the conclusion we can say that the liquid will be flowing downstream in the pipe and the average velocity of the liquid in the pipe is 11.54 m/s.
From the above analysis, we can conclude that the liquid will be flowing downstream in the pipe and the average velocity of the liquid in the pipe is 11.54 m/s. This can be explained using Bernoulli's principle and Reynolds number.
To know more about Bernoulli's principle visit:
brainly.com/question/13098748
#SPJ11
10. Which of the following will react slowest in Sא2 reaction? 3 pts a. 2.Bromooctane b. 3-Bromo-3-methy hexane c. 1-Bromopentane d 2lodohexane
Therefore, option d) 2-Iodohexane will react slowest in an S2 reaction due to the significant steric hindrance caused by the large iodine atom.
In an S2 reaction, the nucleophile attacks the carbon atom while the leaving group (bromine) is being expelled. Steric hindrance occurs when there are bulky groups surrounding the carbon atom, making it more difficult for the nucleophile to approach and react.
a) 2-Bromooctane: This compound has a long carbon chain, but it does not have significant steric hindrance around the carbon atom attached to the bromine.
b) 3-Bromo-3-methylhexane: This compound has a methyl group (CH3) attached to the carbon atom adjacent to the bromine. The methyl group adds some steric hindrance, making the reaction slower than in option a).
c) 1-Bromopentane: This compound has a shorter carbon chain compared to the previous two options. It has less steric hindrance around the carbon atom attached to the bromine, resulting in a faster reaction than in options a) and b).
d) 2-Iodohexane: This compound has a larger iodine atom instead of bromine. Iodine is larger and bulkier than bromine, leading to increased steric hindrance. Therefore, this compound will react the slowest among the given options.
To know more about steric hindrance,
https://brainly.com/question/29817589
#SPJ11
[5 marks] Determine the splitting field E of the polynomail x^3+2 over Q. (a) Write down the Galois group Gal(E/Q). (b) Write down all the subgroups of Gal(E/Q). (c) Down all the subfields L of E and their corresponding subgroups Gal(E/L) in Gal(E/Q).
(a) The Galois group Gal(E/Q) is isomorphic to the group of permutations of the three roots of the polynomial x^3+2.
(b) The subgroups of Gal(E/Q) are the identity subgroup, the subgroups generated by single transpositions, the subgroup generated by cyclic permutations, and the entire Galois group Gal(E/Q).
(c) The subfields L of E correspond to the fixed fields of the subgroups of Gal(E/Q), with Gal(E/E) = {identity}, Gal(E/L) corresponding to the subfield fixed by the corresponding subgroup.
To determine the splitting field E of the polynomial x^3+2 over Q, we need to find the field extension that contains all the roots of the polynomial.
To find the roots, we set the polynomial equal to zero and solve for x:
x^3 + 2 = 0
By factoring out a 2, we can rewrite the equation as:
x^3 = -2
Taking the cube root of both sides, we get:
x = -2^(1/3)
So, the roots of the polynomial are -2^(1/3), ω(-2)^(1/3), and ω^2(-2)^(1/3), where ω is a complex cube root of unity.
The splitting field E of the polynomial x^3+2 over Q is the smallest field extension of Q that contains all the roots of the polynomial. In this case, we can see that the roots of the polynomial are complex numbers, so the splitting field E is the field extension of Q that contains the complex numbers -2^(1/3), ω(-2)^(1/3), and ω^2(-2)^(1/3).
The Galois group Gal(E/Q) is the group of automorphisms of the splitting field E that fix the field Q. In this case, since E is a field extension of Q that contains complex numbers, the Galois group Gal(E/Q) is isomorphic to the group of permutations of the three roots of the polynomial x^3+2.
The subgroups of Gal(E/Q) can be obtained by considering the possible permutations of the three roots of the polynomial x^3+2. The subgroups of Gal(E/Q) are:
- The identity subgroup, which contains only the identity permutation.
- The subgroup generated by a single transposition, which switches two of the roots.
- The subgroup generated by a cyclic permutation, which cyclically permutes the three roots.
- The entire Galois group Gal(E/Q).
The subfields L of E can be obtained by considering the fixed fields of the subgroups of Gal(E/Q). The corresponding subgroups Gal(E/L) in Gal(E/Q) are:
- The fixed field of the identity subgroup is E itself, so Gal(E/E) = {identity}.
- The fixed field of the subgroup generated by a single transposition is the subfield of E that is fixed by that transposition.
- The fixed field of the subgroup generated by a cyclic permutation is the subfield of E that is fixed by that cyclic permutation.
- The fixed field of the entire Galois group Gal(E/Q) is Q itself.
To learn more about polynomial visit : https://brainly.com/question/1496352
#SPJ11
Consider the function z = sin(xy), where x=2t+1 and y = 2t-1. Use the chain rule for multivariable functions to calculate Express your final answers in terms of t. dz dt Note: It is possible answer this problem without using the chain rule for multivariable functions. You are welcome to check your answer using other methods, but to receive full credit for the problem you must use the chain rule that you were taught in the videos for this course.
The expression for dz/dt in terms of t is 2cos(4t^2 - 1) * (2t - 1 + (4t^2 - 1)).
To find dz/dt, we can apply the chain rule for multivariable functions. The chain rule states that when we have a composition of functions, z = f(g(x)), the derivative dz/dx is given by dz/dx = (dz/dg) * (dg/dx).
In this case, we have z = sin(xy), where x = 2t + 1 and y = 2t - 1. By finding the partial derivatives dz/dx and dz/dy, we determine that dz/dx = cos(xy) * y and dz/dy = cos(xy) * (4t^2 - 1).
To obtain dz/dt, we apply the chain rule again: dz/dt = (dz/dx) * (dx/dt) + (dz/dy) * (dy/dt). After substituting the expressions for dz/dx, dz/dy, dx/dt, and dy/dt, we simplify to dz/dt = 2cos(4t^2 - 1) * (2t - 1 + (4t^2 - 1)).
Therefore, the expression for dz/dt in terms of t is 2cos(4t^2 - 1) * (2t - 1 + (4t^2 - 1)).
This formula allows us to calculate the rate of change of z with respect to t for the given function sin(xy) and the variables x and y dependent on t.
To learn more about chain rule click here
brainly.com/question/30764359
#SPJ11
Water is flowing in a pipeline 600 cm above datum level has a velocity of 10 m/s and is at a gauge pressure of 30 KN/m2. If the mass density of water is 1000 kg/m3, what is the total energy per unit weight of the water at this point? Assume acceleration due to Gravity to be 9.81 m/s2.
The total energy per unit weight of the water at the specified point is determined by adding the kinetic energy per unit weight and the potential energy per unit weight of the fluid. According to the principle of conservation of energy, the total energy per unit weight of the fluid in a flow system is constant and is known as Bernoulli's equation.
The following formula can be used to determine the total energy per unit weight of the water at the specified point: T.E./w = P/w + V^2/2g + Z. Where, T.E./w = Total energy per unit weightP/w = Pressure energy per unit weightV = Velocity of the water, g = Acceleration due to gravity Z = Potential energy per unit weight of the water in the pipeline. Thus, putting all the given values into the equation, we get:T.E./w = 30 × 103/1000 + (10)2/(2 × 9.81) + 600/1000= 30 + 5.092 + 0.6= 35.692 m. Therefore, the total energy per unit weight of water at the given point is 35.692 m. Water flows through pipelines due to the pressure difference between two points, and the velocity of the fluid inside the pipeline is determined by the pressure and other factors, such as the diameter of the pipe, the roughness of the surface of the pipe, and the viscosity of the fluid. Bernoulli's equation is a fundamental principle of fluid mechanics that explains how the energy of a fluid changes as it flows along a pipeline or around a curve. It is the basic principle used to describe the behavior of fluids in motion. Bernoulli's equation can be used to calculate the total energy per unit weight of a fluid at a given point in the pipeline by adding the kinetic energy per unit weight and the potential energy per unit weight of the fluid. In this problem, water is flowing through a pipeline 600 cm above datum level, with a velocity of 10 m/s and a gauge pressure of 30 KN/m2, and the mass density of water is 1000 kg/m3. We have to calculate the total energy per unit weight of water at this point. Using Bernoulli's equation, we can obtain the following expression: T.E./w = P/w + V^2/2g + Z, Where, T.E./w = Total energy per unit weight P/w = Pressure energy per unit weight, V = Velocity of the water, g = Acceleration due to gravity, Z = Potential energy per unit weight of the water in the pipe line. Putting the given values into the equation, we get: T.E./w = 30 × 103/1000 + (10)2/(2 × 9.81) + 600/1000= 30 + 5.092 + 0.6= 35.692 m, Thus, the total energy per unit weight of water at the given point is 35.692 m.
In conclusion, the total energy per unit weight of water at a point 600 cm above datum level in a pipeline with a velocity of 10 m/s and a gauge pressure of 30 KN/m2, with a mass density of 1000 kg/m3, is 35.692 m.
Learn more about Bernoulli's equation visit:
brainly.com/question/29865910
#SPJ11
Your family is considering investing $10,000 in a stock and made this graph to track Its growth over time. It is estimated it will grow 7% per year. Write the function that represents the exponential growth of the investment.
The function representing the exponential growth of the investment is:
A(t) = $10,000 * (1 + 0.07)^t
To represent the exponential growth of the investment, we can use the formula for compound interest:
A = P(1 + r/n)^(nt)
Where:
A = the final amount after time t
P = the principal amount (initial investment)
r = annual interest rate (as a decimal)
n = number of times interest is compounded per year
t = time in years
In this case, the initial investment is $10,000, and the growth rate is 7% per year (0.07 as a decimal). We'll assume the interest is compounded annually, so n = 1.
The investment's exponential growth function is represented by the:
A(t) = 10000(1 + 0.07)^t
Simplifying further:
A(t) = 10000(1.07)^t
This function shows how the investment will grow over time, with the value of t representing the number of years.
for such more question on exponential growth
https://brainly.com/question/19961531
#SPJ8
Which of the following matches the answers you put for product on each of the word problems (check all that is correct) (equilibrium)
(Economics)
Automobiles
Televisions
Crude oil
Oranges
Pepsi
We can fill up the result of each of the events as follows:
If the local union in an automobile market negotiates a 20% pay raise in the market, the supply of cars might reduce because of an increase in production costs but the productivity of employees might increase and cause improved production If the president signs a bill to have the IRS send a refund in taxes to all Americans, the television market will experience a boom. If OPEC passes an agreement to restrict crude oil production, there will be a sharp spike in the gasoline market.If an unexpected winter storm damages the Florida orange crop, the market for orange juice will experience a decline and a lack of patronage.If Coca-Cola decides to drop the price of its can from 50 to 30 cents then the market will experience an increase in sales volume.How to fill up the chartTo fill up the chart, you have to carefully consider the events happening and determine whether they would impact the organization positively or negatively.
In the first instance, we are told that the automobile market increases the wages of its workers. First, this might cause an increase in their cost of production, thus reducing the revenue made. Also, the employees might experience more satisfaction and improve their productivity.
Also, if Coca-Cola drops the price of its can from 50 to 30 cents, then it might experience an increase in sales volume.
Learn more about economics here:
https://brainly.com/question/17996535
#SPJ1
A 1.44-g sample of an unknown gas has a volume of 573 mL and a pressure of 809mmHg at 44.8∘C. Calculate the molar mass of this compound. g/m0l
The molar mass of the unknown compound is 73.8 g/mol.
Given: Mass (m) = 1.44 g
Volume (V) = 573 mL
Pressure (P) = 809 mmHg
Temperature (T) = 44.8 ∘C
The Ideal Gas Law is defined as
PV = nRT where P = pressure V = volume R = gas constant T = temperature n = moles of gas.
The first step is to convert the given volume into liters because the value of R used in the ideal gas law has units of
L•atm/mol•K.1 m
L = 0.001 L573 m
L = 0.573 L
Let's convert the temperature from degrees Celsius to Kelvin by adding 273.150.15 K = 318.95 K
Now the Ideal Gas Law can be written as:
PV = nRTn = (PV)/(RT)
Substitute the given values: n = (0.809 atm x 0.573 L)/((0.0821 L•atm/mol•K) x 318.15 K)
n = 0.0195 mol
Let's use the formula of molar mass.
Molar mass = mass/moles
Substitute the given values. molar mass = 1.44 g/0.0195 mol
molar mass = 73.8 g/mol
Therefore, the molar mass of the unknown compound is 73.8 g/mol. This is the required answer.
Learn more about Ideal Gas Law
brainly.com/question/30458409
#SPJ11
What is the equilibrium constant for a reaction at temperature 56.1 °C if the equilibrium constant at 22.7 °C is 46.3?
Express your answer to at least two significant figures.
For this reaction, ΔrH° = -0.5 kJ mol-1 .
Remember: if you want to express an answer in scientific notation, use the letter "E". For example "4.32 x 104" should be entered as "4.32E4".
The equilibrium constant for a reaction at temperature 56.1 °C can be calculated using the equation:
K2 = K1 * e^(-ΔrH°/R * (1/T2 - 1/T1))
where K2 is the equilibrium constant at 56.1 °C, K1 is the equilibrium constant at 22.7 °C (given as 46.3), ΔrH° is the enthalpy change of the reaction (-0.5 kJ mol-1), R is the gas constant (8.314 J mol-1 K-1), T2 is the temperature in Kelvin (56.1 + 273.15), and T1 is the temperature in Kelvin (22.7 + 273.15).
Plugging in the values, we get:
K2 = 46.3 * e^(-0.5/(8.314) * (1/(56.1 + 273.15) - 1/(22.7 + 273.15)))
Simplifying the equation, we find that the equilibrium constant at 56.1 °C is approximately 19.32.
Know more about equilibrium constant here:
https://brainly.com/question/28559466
#SPJ11
Do you see a scenario where the FDA merges with other authority bodies such as the USDA and in turn have better oversight and control over issues within the dietary supplement industry?
In the realm of regulatory possibilities, it is conceivable that the FDA could potentially collaborate or merge with other authority bodies such as the USDA to enhance oversight and control over issues within the dietary supplement industry.
Such a scenario could lead to improved coordination and enforcement efforts. However, the feasibility and desirability of such a merger would depend on various factors, including legal considerations, administrative challenges, and policy objectives. It is important to note that any potential changes in the organizational structure and authority of regulatory bodies would require careful evaluation and consideration of their potential impact on public health and safety.
To know more about dietary supplement industry,
https://brainly.com/question/29800602
#SPJ11
Nylon is prepared by polymerization of a diamine and a diacid chloride. Draw the structural formulas for the monomers that - You do not have to consider stereochemistry. - Draw one structure per sketcher. Add additional sketchers using the drop-down menu in the bottom right corner. - Separate multiple reactants using the + sign from the drop-down menu.
Nylon is a synthetic polymer made from the polymerization of a diamine and a diacid chloride. The structural formulas for the monomers that form nylon 6,6 are as follows:
Hexamethylenediamine (HMD) reacts with Adipic acid [tex](HOOC - (CH_2)_4 - COOH) to form Nylon 6,6. Hexamethylenediamine has two amine functional groups and Adipic acid has two acid functional groups. They react together to form amide functional groups:
NH_2 -(CH_2)_6-NH_2 and HOOC-(CH_2)_4-COOH, respectively:
2HOOC-(CH_2)_4-COOH + H_2N-(CH_2)_6-NH_2 \ HOOC-(CH_2)_4-(CO)-(NH)-(CH_2)_6-NH-(CO)-(CH_2)_4-COOH
Water is removed from the reaction mixture to form Nylon 6,6: [tex]HOOC-(CH_2)_4-(CO)-(NH)-(CH_2)_6-NH-(CO)-(CH_2)_4-COOH \r HOOC-(CH_2)_4-(CO)-(NH)-(CH_2)_6-(NH)-(CO)-(CH_2)_4-COOH
Hence, the structural formulas for the monomers that form nylon 6,6 are HOOC-(CH_2)_4-(CO)-(NH)-(CH_2)_6-NH-(CO)-(CH_2)_4-COOH.
To know more about formulas visit:
https://brainly.com/question/28537638
#SPJ11
The structural formulas for the monomers used in the preparation of nylon are hexamethylenediamine (HMDA) and adipoyl chloride. These monomers react together to form a repeating unit that can further polymerize to create the nylon polymer.
Nylon is a synthetic polymer that is prepared through the polymerization of a diamine and a diacid chloride. The diamine and diacid chloride react together to form a repeating unit called a monomer, which then links together to form the nylon polymer.
To draw the structural formulas for the monomers, we need to identify the diamine and diacid chloride used in the polymerization process.
One example of a diamine that can be used is hexamethylenediamine (HMDA). Its structural formula is:
H2N(CH2)6NH2
Another example of a diacid chloride is adipoyl chloride. Its structural formula is:
ClC(O)C(O)Cl
When these two monomers react together, they form a repeating unit with the following structure:
HOOC(CH2)4COHN(CH2)6NHCO(CH2)4COOH
This repeating unit can then link together with other units through amide bonds, resulting in the formation of the nylon polymer.
Learn more about monomers
https://brainly.com/question/30278775
#SPJ11
Ethylene is produced by the dehydrogenation of ethane. If the feed includes 0.5 mole of steam (an inert diluent) per mole of ethane at 323 K, 1 bar and if the reaction reaches and equilibrium at 1100 K and 1 bar, determine the amount of heating needed or generated by assuming the complete dehydrogenation of ethane. Use the whole expansion of heat capacity values
The amount of heating needed or generated by assuming the complete dehydrogenation of ethane is 40%
Ethylene is produced by the dehydrogenation of ethane.
If the feed includes 0.5 mole of steam (an inert diluent) per mole of ethane at 323 K, 1 bar and if the reaction reaches and equilibrium at 1100 K and 1 bar,
Consider dehydrogenation r × n of ethane.
C₂H₆ ⇒ C₂H₄ + H₂
To determine the amount of heating needed or generated by assuming the complete dehydrogenation of ethane.
From the r × n 1 mol gm ethane gives 1 mol of ethane & 1 mol fuel includes 0.5 mole of steam (an inert diluent) per mole of ethane.
Therefore, total number of moles on side = 2.5 moles.
Total = 2.5 moles
% composition of ethane
= ethane/n total * 100
= 1/2.5 * 100 = 40%
Therefore, 40% the amount of heating generated complete dehydrogenation of ethane.
Learn more about dehydrogenation of ethane here;
https://brainly.com/question/33409739
#SPJ4