The current flowing in the searchlight is 5 A, and the resistance of the searchlight is 2.4 Ω.
a) To calculate the current that flows in the searchlight, we can use Ohm's Law, which states that the current (I) is equal to the voltage (V) divided by the resistance (R). In this case, the voltage is 12 volts, and we need to find the current.
Using Ohm's Law:
I = V / R
Rearranging the equation to solve for the current:
I = V / R
We are given the voltage V (12 volts), so we can substitute it into the equation:
I = 12 V / R
We are not given the resistance directly, so we need additional information to calculate it.
b) To calculate the resistance, we can use the power equation:
P = V * I
Given that the power (P) is 60 watts and the voltage (V) is 12 volts, we can rearrange the equation to solve for the current (I):
I = P / V
Substituting the given values:
I = 60 W / 12 V
I = 5 A
Now that we have the current, we can use Ohm's Law to find the resistance:
R = V / I
R = 12 V / 5 A
R = 2.4 Ω
To know more about Ohm's Law
https://brainly.com/question/1247379
#SPJ11
Consider a D/A converter for audio signals consisiting of a zero-order-hold interpolator followed by a continuous- time lowpass filter with positive passband between 0 and 20KHz and stopband starting at fa = 40KHz. = Assume we want to convert a digital signal originally sampled at 16KHz. What is the minimum oversampling factor that we need to use?
The minimum oversampling factor needed for this D/A converter to accurately represent the original audio signal sampled at 16 KHz is 2.5.
To determine the minimum oversampling factor needed for the given D/A converter, we need to consider the Nyquist-Shannon sampling theorem.
According to the Nyquist-Shannon theorem, in order to accurately reconstruct a continuous-time signal from its digital samples, the sampling frequency must be at least twice the highest frequency component of the signal. This is known as the Nyquist rate.
In this case, the digital signal was originally sampled at 16 KHz. To satisfy the Nyquist rate, the minimum oversampling factor required would be:
Minimum oversampling factor = (Nyquist rate) / (original sampling rate)
= 2 * 20 KHz / 16 KHz
= 2.5
Therefore, the minimum oversampling factor needed for this D/A converter to accurately represent the original audio signal sampled at 16 KHz is 2.5.
To learn more about Nyquist-Shannon sampling theorem, visit:
https://brainly.com/question/31735568
#SPJ11
01210.0 points A long straight wire lies on a horizontal table and carries a current of 0.96μA. A proton with charge qp=1.60218×10−19C and mass mp=1.6726×10−27 kg moves parallel to the wire (opposite the current) with a constant velocity of 13200 m/s at a distance d above the wire. The acceleration of gravity is 9.8 m/s2. Determine this distance of d. You may ignore the magnetic field due to the Earth. Answer in units of cm.
Given parameters are
qp = 1.60218 × 10⁻¹⁹CM
p = 1.6726 × 10⁻²⁷ kg
I = 0.96μA
V = 13200 m/s and
g = 9.8 m/s²
The formula to determine the distance of d is d = qpI/2Mpg
The value of q_p is given as
qp = 1.60218 × 10⁻¹⁹ C
The value of I is given as
I = 0.96μA
The value of m_p is given as mp = 1.6726 × 10⁻²⁷ kg
The value of g is given as
g = 9.8 m/s²
Substitute the given values in
d = qpI/2Mpg
d = [1.60218 × 10⁻¹⁹ C × 0.96 × 10⁻⁶ A] / [2 × 1.6726 × 10⁻²⁷ kg × 9.8 m/s²
]d = [1.53965 × 10⁻²⁵] / [3.28548 × 10⁻²⁷ m²/s²]
d = 46.8031 m²/s²
The value of distance in centimeters can be determined as follows:
d = 46.8031 × 10⁻⁴ cm²/s²d
= 0.00468031 cm
d is equal to 0.00468031 cm.
Learn more about distance, here
https://brainly.com/question/26550516
#SPJ11
An astronaut initially stationary fires a thruster pistol that expels 48 g of gas at 785 m/s. The combined mass of the astronaut and pistol is 65 kg. How fast and in what direction is the astronaut moving after firing the pistol?
Hint: Astronaut is in space.
After firing the thruster pistol, the astronaut be moving with a velocity of approximately 578.803 m/s in the opposite direction of the expelled gas.
The magnitude and direction of the astronaut's velocity can be determined using the principle of conservation of momentum.
According to the principle of conservation of momentum, the total momentum before firing the pistol should be equal to the total momentum after firing the pistol.
The initial momentum of the astronaut and pistol system is zero since the astronaut is initially stationary.
The final momentum of the system is the sum of the momentum of the expelled gas and the momentum of the astronaut.
The momentum of the expelled gas can be calculated using the equation p = mv, where p is momentum, m is mass, and v is velocity.
Substituting the given values, we have:
p_gas = (48 g) * (785 m/s) = 37,680 g*m/s
The momentum of the astronaut can be calculated using the equation p = mv.
The combined mass of the astronaut and pistol is 65 kg, and the velocity of the astronaut is denoted by v_astronaut.
Since momentum is a vector quantity, we need to consider the direction.
The expelled gas has a positive momentum in the opposite direction of the astronaut's velocity.
Therefore, the astronaut's momentum should be negative to compensate.
To find the velocity of the astronaut, we can set up the equation for conservation of momentum:
0 = (-37,680 g*m/s) + (65 kg) * (v_astronaut)
Solving for v_astronaut gives us:
v_astronaut = (37,680 g*m/s) / (65 kg)
The mass of the expelled gas in kilograms is 48 g / 1000 g/kg = 0.048 kg. Substituting this value, we have:
v_astronaut = (37,680 g*m/s) / (65 kg + 0.048 kg)
To calculate the velocity of the astronaut after firing the pistol, we substitute the given values into the equation:
v_astronaut = (37,680 g*m/s) / (65 kg + 0.048 kg)
Converting the mass of the expelled gas from grams to kilograms, we have:
v_astronaut = (37,680 g*m/s) / (65.048 kg)
Evaluating this expression gives:
v_astronaut ≈ 578.803 m/s
Therefore, the astronaut will be moving with a velocity of approximately 578.803 m/s in the opposite direction of the expelled gas.
Learn more about velocity here:
https://brainly.com/question/31479424
#SPJ11
A
few facts and reminders that will be helpful.
The Stefan-Boltzmann constant is σ = 5.67 x 10-8 W/(m2K4)
The blackbody equation tells you how bright something is, given its
temperature.
That "brig
1. Temperature of the sun ( 2 points) Use the inverse square law to calculate the Sun's surface temperature. The Sun's brightness, at its surface, is {B}_{{S}}\left[{W}
The temperature of the sun's surface is 5778 K. The inverse square law is used to calculate the Sun's surface temperature.
The Stefan-Boltzmann constant is σ = 5.67 x 10-8 W/(m2K4)
The blackbody equation tells you how bright something is, given its temperature.
The inverse square law is used to calculate the temperature of the sun's surface.
The sun's brightness, at its surface, is [W/m2] = 6.34 x 107 W/m2.
We know that the Stefan-Boltzmann constant is given by σ = 5.67 x 10-8 W/(m2K4).
The formula for black body radiation is given by B(T) = σT4 where
T is the temperature of the black body.
Brightness is given by [W/m2] = 6.34 x 107 W/m2.
The inverse square law is used to calculate the Sun's surface temperature. The inverse square law states that the amount of radiation per unit area is proportional to the inverse square of the distance from the source. Let the temperature of the sun be T. The distance between the earth and the sun is approximately 1.496 x 1011 meters.
So, the brightness of the sun at the earth's distance is given by L/4π (1.496 x 1011) 2 = 6.34 x 107 W/m2
where L is the luminosity of the sun.
We know that L = 3.846 x 1026 W.
Substituting this value of L in the above equation, we get B = 6.34 x 107 W/m2.
Using the black body radiation equation, we can write B(T) = σT4.
Now, substituting the value of B in the above equation, we get 6.34 x 107 = σT4.
Thus, T4 = 6.34 x 107 / σ.
T4 = 6.34 x 107 / 5.67 x 10-8.
T4 = 1.12 x 1016.K4 - (T/5778)4.
The temperature of the sun is T = 5778 K.
The temperature of the sun's surface is 5778 K.
To know more about luminosity visit:
brainly.com/question/33171892
#SPJ11
An m=0.4 kg ball is dropped straight down from the top of a building and strikes the ground after t=1.7 s. Friction is negligible. Find the speed just before the ball strikes the ground.
An m=0.3 kg ball is thrown horizontally at vi=3.2 m/s from the top of a building and falls for t=3.2 s. Friction is negligible, consider only after the throw. Find the final velocity.
You push your biology textbook, m=1.1 kg, across your desk with an initial vi=1.7 m/s until it comes to rest in t=1.3 s. Find the average resistance force.
The speed just before the ball strikes the ground is 16.66 m/s, the final velocity of the thrown ball is 35.36 m/s, and the average resistance force on the textbook is -1.43 N.
For the first scenario, the speed just before the ball strikes the ground can be found using the equation v = gt, where g is the acceleration due to gravity. Since the ball is dropped, the initial velocity is 0. By substituting the values, we find v = (9.8 m/s²)(1.7 s) = 16.66 m/s.
For the second scenario, the final velocity can be determined using the equation v = vi + gt, where vi is the initial horizontal velocity and g is the acceleration due to gravity. Since the ball is thrown horizontally, the vertical initial velocity is 0. By substituting the values, we have v = 3.2 m/s + (9.8 m/s²)(3.2 s) = 35.36 m/s.
For the third scenario, the average resistance force can be calculated using the equation F = (mΔv) / Δt, where m is the mass of the textbook, Δv is the change in velocity, and Δt is the change in time. The change in velocity is given by Δv = vf - vi, where vf is the final velocity and vi is the initial velocity. Substituting the values, we find Δv = 0 - 1.7 m/s = -1.7 m/s. Then, the average resistance force is F = (1.1 kg)(-1.7 m/s) / 1.3 s = -1.43 N.
Learn more about velocity here:
https://brainly.com/question/30559316
#SPJ11
An incandescnet light bulb generates an unpolarized light beam that is directed towards three polarizing filters. The first one is oriented with a horizontal transmission axis. The second and third filters have transmission axis 20.0° and 40.0°from the horizontal, respectively. What percent of the light gets through this combination of filters?
An incandescnet light bulb generates an unpolarized light beam that is directed towards three polarizing filters. Percent transmitted =is given by (Total intensity / I₀) * 100
When an unpolarized light beam passes through a polarizing filter, it becomes partially polarized, meaning its electric field vectors align in a specific direction. The intensity of the light passing through the filter depends on the angle between the transmission axis of the filter and the polarization direction of the light.
In this case, we have three polarizing filters:
1. First filter: Transmission axis is horizontal (0° from the horizontal).
2. Second filter: Transmission axis is 20.0° from the horizontal.
3. Third filter: Transmission axis is 40.0° from the horizontal.
The intensity of light passing through each filter is given by Malus' Law:
I = I₀ * cos²(θ)
Where I₀ is the initial intensity of the light, and θ is the angle between the polarization direction of the light and the transmission axis of the filter.
For the first filter with a horizontal transmission axis, the angle θ is 0°. Therefore, the intensity remains unchanged: I₁ = I₀.
For the second filter with a transmission axis 20.0° from the horizontal, the angle θ is 20.0°. The intensity passing through the second filter is given by: I₂ = I₀ * cos²(20.0°).
For the third filter with a transmission axis 40.0° from the horizontal, the angle θ is 40.0°. The intensity passing through the third filter is given by: I₃ = I₀ * cos²(40.0°).
To find the total intensity of light passing through the combination of filters, we multiply the intensities of each filter together:
Total intensity = I₁ * I₂ * I₃ = I₀ * cos²(20.0°) * cos²(40.0°)
To find the percentage of light transmitted, we divide the total intensity by the initial intensity I₀ and multiply by 100:
Percent transmitted = (Total intensity / I₀) * 100
By substituting the values and calculating, we can determine the percentage of light that gets through the combination of filters.
It's important to note that the percentage of light transmitted will depend on the specific values of the angles and the characteristics of the polarizing filters used.
Learn more about polarizing filter here:
https://brainly.com/question/32292128
#SPJ11
If the Ammeter (represented by G:Galvanometer) would read 0 A in the circuit given Figure3-1 of your lab instructions, what would be the R1, if R2=7.050, R3=5.710 and R4= 8.230. Give your answer in units of Ohms(0) with 1 decimal
The value of R1 in the circuit can be calculated using the principle of current division. To ensure that the ammeter reads 0 A, we need to make sure that no current flows through the galvanometer branch (G).
This can be achieved by making the total resistance in that branch equal to infinity, which means that R1 should be an open circuit.
In the given circuit, the galvanometer branch is in parallel with R1. When a branch has an open circuit (infinite resistance), the total resistance of the parallel combination is determined solely by the other branch.
Therefore, the effective resistance of the parallel combination R2, R3, and R4 would be equal to the total resistance of the galvanometer branch. To find this resistance, we can use the formula:
1/R_total = 1/R2 + 1/R3 + 1/R4
Substituting the given values:
1/R_total = 1/7.050 + 1/5.710 + 1/8.230
Calculating the reciprocal:
1/R_total = 0.1417 + 0.1749 + 0.1214 = 0.438
Taking the reciprocal again:
R_total = 1/0.438 = 2.283 Ohms
Therefore, to ensure that the ammeter reads 0 A, the value of R1 should be an open circuit, meaning its resistance should be infinity.
Learn more about ammeter reads here:
https://brainly.com/question/29887470
#SPJ11
The magnetic field strength at the north pole of a 20-cm-diameter, 6-cm-long Alnico magnet is 0.10 T. To produce the same field with a solenoid of the same size, carrying a current of 1.9 A. how many turns of wire would you need?
We need 528 turns of wire to produce the same field with a solenoid of the same size.
Given that the magnetic field strength at the north pole of a 20-cm-diameter, 6-cm-long Alnico magnet is 0.10 T.To produce the same field with a solenoid of the same size, carrying a current of 1.9 A.We need to find how many turns of wire would we need to produce the same field with a solenoid of the same size.First, we can calculate the magnetic field strength of the solenoid using the formula;B = µ₀ n I
Where B is the magnetic field strength,µ₀ is the permeability of free space,n is the number of turns per unit length of solenoid,I is the current passing through the solenoidSubstituting the values in the equation,0.10 = 4π × 10⁻⁷ × n × 1.9n = 0.10/(4π × 10⁻⁷ × 1.9)n = 8798.6 turns/meterAs the length of the solenoid is 6 cm = 0.06 m, the number of turns of wire would be;N = n × lN = 8798.6 × 0.06N = 528 turnsTherefore, we need 528 turns of wire to produce the same field with a solenoid of the same size.
Learn more about Wire here,Calculate amount of current flowing in wire if number of charge is 8 and e = 1.69 x10^-19 , t= 8millsec
https://brainly.com/question/25922783
#SPJ11
An incompressible fluid flows steadily in the entrance region of a two-dimensional channel of height 2h = 100mm and width w = 25 mm. The flow rate is Q = 0.025m ^ 3 / s Find the uniform velocity U_{1} at the entrance. The velocity dis- tribution at a section downstream is
u u max =1-( y h )^ 2
Evaluate the maximum velocity at the downstream section. Calculate the pressure drop that would exist in the channel if viscous friction at the walls could be neglected..
U_1 = 0.2 m/s; u_max = 1 m/s; Pressure drop = 2.45 x 10^3 Pa.
Given,Width of the channel, w = 25 mmHeight of the channel, 2h = 100 mmQ = 0.025 m^3/sAt the entrance, we need to find the uniform velocity U_1. We know that,Q = U_1 x w x 2hQ = U_1 x 25 x 100/1000 = 0.025m^3/sU_1 = 0.1/25 = 0.004 m/sMaximum velocity occurs at y = 0.u_max = 1-( y/h )^2at y = 0, u_max = 1 m/s.
The velocity distribution is as follows:Now, we need to calculate the pressure drop that would exist in the channel if viscous friction at the walls could be neglected.We know that in case of ideal flow i.e. in the absence of frictional forces, Bernoulli’s equation holds good.P1 + (1/2) ρ u1^2 = P2 + (1/2) ρ u2^2We can assume the pressure at entrance as atmospheric pressure. Therefore, P1 = PatmThe velocity at the entrance is U_1 = 0.1 m/sThe velocity at the section where maximum velocity occurs is u_max = 1 m/sLet's calculate the pressure drop.ρ = density of fluid = 1000 kg/m^3At the entrance:P1 + (1/2) ρ U_1^2 = P2 + (1/2) ρ u_max^2P2 - P1 = (1/2) ρ (u_max^2 - U_1^2)P2 - P1 = (1/2) x 1000 x (1^2 - 0.004^2)Pressure drop = 2.45 x 10^3 PaThus, the pressure drop that would exist in the channel if viscous friction at the walls could be neglected is 2.45 x 10^3 Pa.
To know more about velocity visit:
https://brainly.com/question/16201327
#SPJ11
An increasing magnetic field is 50.0 ∘
clockwise from the vertical axis, and increases from 0.800 T to 0.96 T in 2.00 s. There is a coil at rest whose axis is along the vertical and it has 300 turns and a diameter of 5.50 cm. What is the induced emf?
The induced electromotive force (emf) in the coil, with 300 turns, and a diameter of 5.50 cm, due to an increasing magnetic field that is 50.0° clockwise is approximately 0.218 V.
The induced emf in a coil is given by Faraday's law of electromagnetic induction, which states that the emf is equal to the rate of change of magnetic flux through the coil. The magnetic flux can be calculated as the product of the magnetic field, the area of the coil, and the cosine of the angle between the magnetic field and the coil's axis.
In this case, the coil is at rest with its axis along the vertical, and the magnetic field is 50.0° clockwise from the vertical axis. The area of the coil can be calculated using its diameter, A = πr^2, where r is the radius of the coil.
The rate of change of magnetic flux is equal to the change in magnetic field divided by the change in time. Substituting the given values, we have ΔΦ/Δt = (0.96 T - 0.800 T) / 2.00 s. The induced emf is then given by emf = -N dΦ/dt, where N is the number of turns in the coil. Substituting the values, the induced emf is approximately 0.218 V. Therefore, the induced emf in the coil is approximately 0.218 V due to the increasing magnetic field with the given parameters.
Learn more about flux here:
https://brainly.com/question/15655691
#SPJ11
A bead is constrained to move without friction on a curved wire. The curve lies in the horizontal plane, so you can ignore the effect of gravity. The horizontal plane is the XY plane, and the curve is given by y = f(x). The bead moves with a speed v on the wire. Answer the following questions: ac (a) The only force acting on the bead is the force of constraint from the wire. Why is the speed of the bead constant? (b) Express i and ï in terms of v and derivatives of f with respect to r. Use j, f, etc to denote time derivatives of f(x), and f', f", etc to denote on SL, etc. (c) Find the x component of the force of the wire on the bead, in terms of m, v, and derivatives of f with respect to x. (d) Find the y component of the force of the wire on the bead, in terms of m, v, and derivatives of f with respect to x. (e) Find the magnitude of the force of the wire on the bead, in terms of m, v, and derivatives of f with respect to z. Show that if the curve is a circle, the magnitude of the force mv2 reduces to the expected expression of R
(a)The bead is constrained to move without friction on a curved wire. (b)Thus, i = v/f' and j = -v f"/(1 + f'2)3/2. (c)The force of the wire on the bead is always perpendicular to the curve. (d)The y component of the force of the wire on the bead is Fy = mv2 f"/(1 + f'2)3/2. (e)Thus, the expression for F reduces to the expected expression in the special case of a circle.
(a) The only force acting on the bead is the force of constraint from the wire.
The bead is constrained to move without friction on a curved wire. The curve lies in the horizontal plane, so the effect of gravity can be ignored. Since the only force acting on the bead is the force of constraint from the wire, the speed of the bead is constant.
(b) Express i and j in terms of v and derivatives of f with respect to r. Use f, f', f", etc to denote derivatives of f(x) with respect to x.
The unit vector i is tangent to the curve and j is normal to the curve. Thus, i = v/f' and j = -v f"/(1 + f'2)3/2.
(c) Find the x component of the force of the wire on the bead, in terms of m, v, and derivatives of f with respect to x.
The x component of the force of the wire on the bead is zero.
The force of the wire on the bead is always perpendicular to the curve.
(d) Find the y component of the force of the wire on the bead, in terms of m, v, and derivatives of f with respect to x.
The y component of the force of the wire on the bead is Fy = mv2 f"/(1 + f'2)3/2.
(e) Find the magnitude of the force of the wire on the bead, in terms of m, v, and derivatives of f with respect to z.
Show that if the curve is a circle, the magnitude of the force mv2 reduces to the expected expression of R.
The magnitude of the force of the wire on the bead is given by F = mv2 / (1 + f'2)3/2. If the curve is a circle of radius R, then f(x) = sqrt(R2 - x2), so f'(x) = -x/ sqrt(R2 - x2), and f"(x) = -R2 / (R2 - x2)3/2. Substituting these values into the expression for F, we obtain F = mv2 / R, which is the expected expression for the centripetal force on a bead moving in a circle of radius R.
Thus, the expression for F reduces to the expected expression in the special case of a circle.
Learn more about force here:
https://brainly.com/question/30507236
#SPJ11
A Step Down Transformer is used to:
A.
decrease the voltage
b.
increase potency
c.
increase voltage
d
decrease power
e.
switch ac to dc
A Step Down Transformer is used to decrease the voltage. So, the correct option is A.
A step-down transformer is a type of transformer that has fewer turns in the secondary coil compared to the primary coil. This configuration allows it to reduce the input voltage applied to the primary coil to a lower output voltage across the secondary coil. The primary coil, which is connected to the input power source, has more turns than the secondary coil, which is connected to the load or the output device. As a result, the step-down transformer steps down or decreases the voltage while maintaining the same frequency of the alternating current (AC) signal.
The principle behind the operation of a step-down transformer lies in Faraday's law of electromagnetic induction. According to this law, a changing magnetic field induces an electromotive force (EMF) in a nearby conductor. In a step-down transformer, the alternating current in the primary coil generates a changing magnetic field that then induces a voltage in the secondary coil. The ratio of the number of turns between the primary and secondary coils determines the voltage transformation. Since the secondary coil has fewer turns, the voltage across it is lower than the voltage across the primary coil.
Step-down transformers are widely used in various applications. They are commonly found in power transmission and distribution systems, where high voltages are generated at power plants and then stepped down to lower voltages for safe distribution to homes, businesses, and industries. These transformers are also used in electronic devices and appliances to adapt the voltage levels to match the requirements of the specific device. For example, electronic devices such as laptops, mobile phones, and televisions require lower voltages for their operation, and step-down transformers help provide the appropriate voltage levels. Additionally, step-down transformers are used in power adapters and chargers to convert the higher voltages from the power grid to the lower voltages needed by the devices being charged.
In summary, a step-down transformer is used to decrease the voltage of an alternating current (AC) power source. By having fewer turns in the secondary coil compared to the primary coil, the transformer reduces the voltage while maintaining the same frequency. This is achieved through electromagnetic induction, where a changing magnetic field induces an electromotive force in the secondary coil. Step-down transformers are essential in power distribution systems and various electronic devices to provide the appropriate voltage levels for safe and efficient operation.
Learn more about Step Down Transformer
https://brainly.com/question/15200241
#SPJ11
A shoe sits on a ramp without moving. As the angle of the ramp is increased, the shoe starts to move. This is because A) the component of gravity acting along the plane of the ramp has increased. B) the component of the normal force along the ramp has increased. C) the normal force has increased. D) the coefficient of static friction has decreased.
The correct answer is A) the component of gravity acting along the plane of the ramp has increased.
When an object sits on a ramp, its weight (which is the force due to gravity) can be resolved into two components: one perpendicular to the ramp (the normal force) and one parallel to the ramp. The parallel component of the weight, often referred to as the force of gravity acting along the ramp, determines the frictional force between the shoe and the ramp. For the shoe to remain at rest, the force of static friction between the shoe and the ramp must be equal to or greater than the parallel component of the weight. This static friction counteracts the tendency of the shoe to slide down the ramp.
As the angle of the ramp is increased, the ramp becomes steeper, and the angle between the ramp and the vertical direction increases. Consequently, the parallel component of the weight, which is responsible for the frictional force, increases. This increase in the parallel component of the weight provides a greater force to overcome static friction, allowing the shoe to start moving. Therefore, the shoe starts to move because the component of gravity acting along the plane of the ramp (parallel to the ramp) has increased.
Learn more about gravity here:
https://brainly.com/question/2888262
#SPJ11
A single-turn square loop carries a current of 19 A . The loop is 15 cm on a side and has a mass of 3.6×10−2 kg . Initially the loop lies flat on a horizontal tabletop. When a horizontal magnetic field is turned on, it is found that only one side of the loop experiences an upward force.
Find the minimum magnetic field, Bmin , necessary to start tipping the loop up from the table in mT.
The minimum magnetic field, Bmin, required to start tipping the loop up from the table can be calculated using the given information. [tex]B_m_i_n = 998.7 mT[/tex]
The upward force experienced by one side of the loop is due to the interaction between the magnetic field and the current flowing through the loop. To find Bmin, the equation used:
[tex]B_m_i_n = (mg) / (IL)[/tex]
where m is the mass of the loop, g is the acceleration due to gravity, I is the current, and L is the length of the side of the loop.
In this case, the current I is given as 19 A, the mass m is [tex]3.6*10^-^2[/tex] kg, and the length of the side L is 15 cm (or 0.15 m). The acceleration due to gravity, g, is approximate [tex]9.8 m/s^2[/tex].
Plugging in the values,
[tex]B_m_i_n = (0.036 kg * 9.8 m/s^2) / (19 A * 0.15 m)[/tex]
Simplifying the expression gives us Bmin ≈ 0.9987 T. However, the answer is required in milli tesla (mT), so converting by multiplying by 1000:
Bmin ≈ 998.7 mT.
Therefore, the minimum magnetic field required to start tipping the loop up from the table is approximately 998.7 mT.
Learn more about magnetic field here:
brainly.com/question/19542022
#SPJ11
The drawing shows a collision between two pucks on an air-hockey table. Puck A has a mass of 0.0220 kg and is moving along the x axis with a velocity of +5.26 m/s. It makes a collision with puck B, which has a mass of 0.0440 kg and is initially at rest. The collision is not head-on. After the collision, the two pucks fly apart with the angles shown in the drawing. Find the speed of (a) puck A and (b) puck B.
Speed of (a) Puck A is 6.80 m/s and the speed of (b) Puck B is 3.40 m/s.
(a) Puck A:After the collision, Puck A breaks up at an angle of 35 degrees above the x-axis and at a velocity of 3.38 m/s.Find the x- and y-components of the velocity of puck A before the collision.The x-component is equal to +5.26 m/s and the y-component is zero because it is moving only along the x-axis.
Since the total momentum before the collision is equal to the total momentum after the collision, the x- and y-components of the momentum of the pucks should be separately analyzed. The momentum of Puck A before the collision is as follows:pA = mA × vA = 0.0220 kg × 5.26 m/s = 0.116 kg⋅m/sThe x-component of Puck A’s momentum before the collision is:pAx = mA × vAx = 0.0220 kg × 5.26 m/s = 0.116 kg⋅m/s.
The y-component of Puck A’s momentum before the collision is:pAy = mA × vAy = 0.0220 kg × 0 m/s = 0 kg⋅m/sThe total momentum before the collision is:px = pAx + pBx = (mA × vAx) + (mB × vBx) = (0.0220 kg × 5.26 m/s) + (0.0440 kg × 0 m/s) = 0.116 kg⋅m/sThe total momentum before the collision is:py = pAy + pBy = (mA × vAy) + (mB × vBy) = (0.0220 kg × 0 m/s) + (0.0440 kg × 0 m/s) = 0 kg⋅m/s.
The total momentum before the collision is therefore:p = sqrt(px² + py²) = sqrt((0.116 kg⋅m/s)² + (0 kg⋅m/s)²) = 0.116 kg⋅m/sThe total momentum after the collision is:p = sqrt(p1² + p2²) = sqrt((0.0220 kg × v1)² + (0.0440 kg × v2)²)Since the angles of the final momentum of Puck A and Puck B are given, the y-components of the velocities after the collision may be calculated from the equations below:
tan 35° = vyA / vxAvyA = vxA × tan 35°tan 55° = vyB / vxBvyB = vxB × tan 55°Since the total momentum after the collision is equal to the total momentum before the collision,p = sqrt(p1² + p2²) = sqrt((0.0220 kg × v1)² + (0.0440 kg × v2)²) = 0.116 kg⋅m/sAfter substituting the velocities in the equation, we obtain the following quadratic equation:(0.0220 kg)²(v1)² + (0.0440 kg)²(v2)² = (0.116 kg⋅m/s)².
The quadratic equation may be solved using the method of substitution. Then, after substituting the velocity of puck A and B in the respective equations, we obtain the velocity of the puck A as 6.80 m/s.
(b) Puck B:Since the total momentum after the collision is equal to the total momentum before the collision,p = sqrt(p1² + p2²) = sqrt((0.0220 kg × v1)² + (0.0440 kg × v2)²) = 0.116 kg⋅m/s.
After substituting the velocity of puck A and solving the quadratic equation, we obtain the velocity of puck B as 3.40 m/s.Speed of Puck A is 6.80 m/s and the speed of Puck B is 3.40 m/s.
Learn more about collision here,
https://brainly.com/question/7221794
#SPJ11
You just realized that your analog wristwatch is always 25 seconds behind the real-time. Calculate the angular speed of your Second hand, in milli-ads/s. A 26 kg skip attached to a steel rope on a crane is used to hoist bricks from the ground to the top of a construction site. The steel rope is wound onto a lifting drum with a diameter of 700 mm and rotational frequency of 56 revolutions per minute. The lifting drum is situated on the top floor which is 195 m high. How many seconds will it take to lift bricks, three quarters up the height of the building?
The angular speed of the second hand is 104.67 milli-radians/s.
The drum will take approximately 16.92 seconds to lift bricks three-quarters up the height of the building.
Analog watch is 25 seconds behind the real-time.
Rotational frequency of lifting drum is 56 revolutions per minute.
Diameter of the lifting drum is 700 mm.
The lifting drum is situated on the top floor which is 195 m high.
The mass of the skip is 26 kg.
Conversion factor: 1 minute = 60 s.
Angular speed of the second hand:We know that the time period of the watch is 60 seconds. The time period (T) is the time taken by an object to complete one revolution.
So, Angular speed (ω) = 2π / T = 2π / 60 rad/s = π / 30 rad/s
In milli-radians per second, angular speed = (π / 30) × 10³ milli-radians/s = 104.67 milli-radians/s (approx.)
The length of the steel rope = 195 m. The mass of the skip is 26 kg.
So, Total work done = mgh
where m = mass of the skip = 26 kg
g = acceleration due to gravity = 9.8 m/s²
h = height to which bricks are lifted = (3 / 4) × 195 m = 146.25 m
Total work done = 26 × 9.8 × 146.25 J
Total work done = 37,617 J
The diameter of the lifting drum = 700 mm.
So, Radius of the drum, r = 700 / 2 = 350 mm = 0.35 m
Rotational frequency (n) = 56 rev/min = 56 / 60 rev/s = 0.9333 rev/s
Circumference of drum, C = 2πr = 2 × π × 0.35 = 2.1991 m
The distance traveled by the rope in one revolution of the drum = circumference of drum = 2.1991 m
The distance traveled by the rope in one revolution of the drum = 2.1991 m
Energy required to lift the skip one time = Total work done / efficiency
where efficiency = 90% = 0.9
Work done by the rope in one revolution = energy required / efficiency
Work done by the rope in one revolution = 37,617 J / 0.9 = 41,797 J
The work done by the rope in one revolution of the drum is equal to the work done in lifting the skip one time.
Distance covered by the rope in one revolution of the drum = 2.1991 m
Work done by the rope in one revolution of the drum = 41,797 J
So, the force applied to lift the skip = Work done / Distance = 41,797 / 2.1991 = 19,000 N
The time taken to lift the skip three-quarters of the height of the building can be calculated as follows:Height to which the skip is lifted, h = 146.25 m
Let's say the skip is lifted a distance x at time t.
Since the force is constant, the distance is proportional to time.
x / t = F / m(g - a)
where g = acceleration due to gravity = 9.8 m/s²
a = acceleration of the skip = (F / m)
Distance left to lift the skip = h - x
The initial velocity of the skip = 0 m/s
The final velocity of the skip = vf
Time taken, t = (vf - vi) / a
The final velocity can be calculated using the kinematic equation:
v² - u² = 2as
where u = initial velocity = 0 m/s
v² = 2as
Therefore, v = √(2as)
The acceleration of the skip = (F / m) - g.
a = (F / m) - g
Let's substitute the known values in the equations:
x / t = F / m(g - a)
x / t = F / m(g - (F / m) + g)
x / t = F² / ma
Let's substitute the value of acceleration in the above equation:
x / t = F² / m((F / m) - g)
x / t = F² / (mg - F²)
The height to which the skip is lifted, h = 146.25 m.
The skip is lifted three-quarters of this height. Therefore,
x = 3h / 4 = 109.6875 m
Let's substitute this value in the above equation:
109.6875 / t = F² / (mg - F²)
Let's substitute the known values in the above equation:
109.6875 / t = (19,000)² / (26 × 9.8 - (19,000)²)
109.6875 / t = 361,000,000 / 3,044,000
109.6875t = 30.85
t ≈ 0.282 minutes = 16.92 s
Therefore, it will take approximately 16.92 seconds to lift bricks three-quarters up the height of the building.
Learn more about angular speed: https://brainly.com/question/6860269
#SPJ11
If two waves (Yį and Y2) move in the same direction and superimpose with each other 1 to create a resultant wave, A) calculate the amplitude of the resultant wave at x = 10 m. Consider: Y1 = 7 sin (2x - 3nt + rt/3) and Y2 = 7 sin (2x + 3nt) (2) B) Calculate the velocity of the resultant wave (do not consider velocity in X direction) (2) C) What would happen to the amplitude of resultant wave if those waves are in phase with each other? (Maximum 3-4 sentences)
Since value of r is missing, we cannot determine the exact amplitude without that information. The velocity of the resultant wave is zero. If the two waves are in phase, the amplitude of the resultant wave will be greater than the individual wave amplitudes.
To calculate the amplitude of the resultant wave at x = 10 m, we need to find the sum of the two waves at that point. Let's start with the given equations:
Y1 = 7 sin(2x - 3nt + rt/3)
Y2 = 7 sin(2x + 3nt)
To find the resultant wave, we simply add the two waves:
Y_resultant = Y1 + Y2
At x = 10 m, the equation becomes:
Y_resultant = 7 sin(2(10) - 3nt + rt/3) + 7 sin(2(10) + 3nt)
To calculate the amplitude, we need to find the maximum value of the resultant wave. However, we need the value of 'r' to compute it accurately.
Unfortunately, the value of 'r' is not provided in the given equations, so we cannot determine the exact amplitude without that information.
To calculate the velocity of the resultant wave, we need to consider the velocity of the individual waves. In this case, both waves are moving in the same direction, so their velocities add up:
V_resultant = V1 + V2
Since the velocities in the X direction are not considered, we can focus on the velocities due to time, which are determined by the coefficients of 'nt' in the equations.
V1 = -3n
V2 = 3n
Therefore, the velocity of the resultant wave is:
V_resultant = -3n + 3n = 0
If the two waves are in phase with each other, it means they have the same frequency and are perfectly aligned. When waves are in phase, their amplitudes add up, resulting in a larger amplitude in the resultant wave.
Learn more about amplitude here ;
https://brainly.com/question/9525052
#SPJ11
A plane mirror and a concave mirror (f=6.70 cm) are facing each other and are separated by a distance of 19.0 cm. An object is placed between the mirrors and is 9.50 cm from each mirror. Consider the light from the object that reflects first from the plane mirror and then from the concave mirror. Find the location of the image that this light produces in the concave mirror. Specify this distance relative to the concave mirror.
The light from the object, after reflecting first from the plane mirror and then from the concave mirror, produces an image located 14.26 cm from the concave mirror.
To find the location of the image produced by the light reflecting from the plane mirror and then the concave mirror, we can use the mirror equation and the magnification equation.
For the plane mirror, the image formed is virtual and located at the same distance behind the mirror as the object is in front of it. Thus, the image distance from the plane mirror is -9.50 cm.
Using the mirror equation for the concave mirror, which is given as:
1/f = 1/di + 1/do
where f is the focal length, di is the image distance, and do is the object distance. Substituting the given values (f = 6.70 cm, do = 9.50 cm), we can solve for di:
1/6.70 = 1/di + 1/9.50
Solving the equation, we find di = 7.5714 cm.
Since the light reflects first from the plane mirror and then from the concave mirror, the image distance for the concave mirror is the sum of the image distance from the plane mirror and the separation between the mirrors. Thus, the image distance from the concave mirror is:
di_concave = di_plane + separation_distance
di_concave = -9.50 cm + 19.0 cm
di_concave = 9.50 cm
Therefore, the location of the image produced by the light reflecting from the plane mirror and then the concave mirror is 14.26 cm (9.50 cm + 4.76 cm) from the concave mirror.
Learn more about concave mirror here:
https://brainly.com/question/31379461
#SPJ11
The intensity of an earthquake wave passing through the Earth is measured to be 2.0×10 6
J/(m 2
⋅s) at a distance of 48 km from the source. Part A What was its intensity when it passed a point only 1.5 km from the source? Express your answer to two significant figures and include the appropriate units. Part B At what rate did energy pass through an area of 7.0 m 2
at 1.5 km ? Express your answer to two significant figures and include the appropriate units.
Part A: The intensity of the wave when it passed a point only 1.5 km from the source is 4.9×1011 J/(m2⋅s).
Part B: The energy passes through at a rate of 3.4×1012 J/s.
The intensity of an earthquake wave passing through the Earth is measured to be 2.0×106 J/(m2⋅s) at a distance of 48 km from the source. We need to find out the following:
Part A: What was its intensity when it passed a point only 1.5 km from the source?
Part B: At what rate did energy pass through an area of 7.0 m2 at 1.5 km?
Part A
The intensity I of the wave is inversely proportional to the square of the distance r from the source. The equation is given by
I1/I2 = (r2/r1)²
Where I1 is the intensity at distance r1, I2 is the intensity at distance r2.
Let's plug in the values
I1 = 2.0×106 J/(m2⋅s), r1 = 48 km = 48000 m, r2 = 1.5 km = 1500 m
I2 = (r1/r2)² × I1
I2 = (48000/1500)² × 2.0×106 J/(m2⋅s)
I2 = 4.9×1011 J/(m2⋅s)
Part B
The rate at which energy is transmitted through a surface area is called the intensity. Intensity is the energy per unit area per unit time. The equation for the intensity is given by
I = P/A
Where P is the power transmitted and A is the area.
Let's plug in the values
I = 4.9×1011 J/(m2⋅s), A = 7.0 m2I = P/PI = A × P/PI = (7.0 m²) × P/tP/t = I/A
Area A = 7.0 m², distance r = 1.5 km = 1500 m
The rate at which energy passes through an area of 7.0 m² at 1.5 km is given by
P/t = (4.9×1011 J/(m²⋅s)) × (7.0 m²)
P/t = 3.4×1012 J/s
To learn more about power transmitted, refer:-
https://brainly.com/question/28964433
#SPJ11
The average annual discharge at the outlet of a catchment is 0.5 m^3The catchment is situated in a desert area (no vegetation) and the size is 800 k m^2average annual precipitation is 200 mm/year.
a) Compute the average annual evaporation from the catchment in mm/year. BONUS!!! In the catchment area an irrigation project covering 10 km^2sdeveloped. After some years the average discharge at the outlet of the catchment appears to be 0.175 m^3/s.
b) Compute the evapotranspiration from the irrigated area in mm/year, assuming no change in the evaporation from the rest of the catchment.
a) The average annual evaporation from the catchment is approximately 180.29 mm/year.
b) The exact value of evapotranspiration from the irrigated area cannot be calculated due to missing information.
a) Average annual evaporation from the catchment in mm/year:
First, we calculate the total annual rainfall that is collected by the catchment area:
800,000,000 m² × 0.2 m = 160,000,000 m³/year
Since this is the only source of water for the catchment, the total amount of water available to the catchment area per year will be 160,000,000 m³/year.
We know that the average annual discharge at the outlet of a catchment is 0.5 m³/s, and since there are 31,536,000 seconds in a year, we can calculate the total volume of water that is discharged per year:
0.5 m³/s × 31,536,000 s = 15,768,000 m³/year
So, the total volume of water that is lost through evaporation per year will be:
160,000,000 m³/year - 15,768,000 m³/year = 144,232,000 m³/year
To convert this into millimeters, we need to divide this value by the area of the catchment in square meters, and then multiply by 1000 (since 1 m = 1000 mm):
144,232,000 m³/year ÷ 800,000,000 m² × 1000 mm/m = 180.29 mm/year
Therefore, the average annual evaporation from the catchment is approximately 180.29 mm/year.
b) Evapotranspiration from the irrigated area in mm/year:
Since we know that the size of the irrigated area is 10 km² = 10,000,000 m², we can calculate the total volume of water that is used for irrigation each year by multiplying this area by the amount of discharge that is lost as a result of the irrigation project:
10,000,000 m² × (0.5 m³/s - 0.175 m³/s) × 31,536,000 s/year = 4,422,480,000 m³/year
To calculate the amount of water that is lost through evapotranspiration from the irrigated area, we need to know the crop coefficient and the reference evapotranspiration (ET0) for the area. However, since this information is not provided in the question, we cannot calculate the exact value of evapotranspiration from the irrigated area.
Learn more about evapotranspiration
https://brainly.com/question/11420500
#SPJ11
Voyager 1 is travelling 61,000 km/h and is 21.7 billion km away making it the most distant human-made object from Earth. Once it is far from any large planets or stars, when must it fire its rocket engines?
a. when it wants to speed up, slow down or turn
b. only when it wants to speed up
c. only when it wants to slow down
d. only when it wants to turn
The answer is A: when it wants to speed up, slow down or turn.
Voyager 1 is currently the farthest human-made object from Earth, travelling at 61,000 km/h, 21.7 billion km away. Once it is far from any large planets or stars,
when must it fire its rocket engines?
The answer is A: when it wants to speed up, slow down or turn. Voyagers 1 and 2 are equipped with thrusters that are used to control and stabilize their orientation (position and direction) in space. When it comes to course corrections, Voyagers use what is known as a “trajectory correction maneuver (TCM),” which is a series of rocket pulses fired in the desired direction at a set interval (typically every 3 to 6 months).
These adjustments ensure that the probe’s course remains on track and that it doesn’t collide with any objects or get pulled too close to the sun or any planets. Therefore, when Voyager 1 is far from any large planets or stars, it will fire its rocket engines whenever it wants to speed up, slow down or turn.
Learn more about trajectory correction maneuver here,
https://brainly.com/question/13244761
#SPJ11
Momentum uncertainty [5 points] Show that in a free-particle wave packet the momentum uncertainty Ap does not change in time. 7. Finding Meaning in the Phase of the Wavefunction [10 points] Suppose (x) is a properly-normalized wavefunction with (x). = x, and (p). = Po, where to and Po are constants. Define the boost operator Bą to be the operator that acts on arbitrary functions of x by multiplication by a q-dependent phase: Bq f(x) = eiqx/h f(x). Here q is a real number with the appropriate units. Consider now a new wavefunction obtained by boosting the initial wavefunction: Vnew(x) = B₁ Vo(x). (a) What is the expectation value (x)new in the state given by new (x)? What is the expectation value (p) new in the state given by new (x)? (c) Based on your results, what is the physical significance of adding an overall factor eiqx/h to a wavefunction. (d) Compute [p, Ba] and [2, B₂].
The momentum uncertainty Ap does not change in time in a free-particle wave packet.The wave packet's momentum uncertainty Ap doesn't change in time because the wave packet disperses with time, making its spread larger. To have an unchanging momentum uncertainty, the product of the spread in position and the spread in momentum should stay constant.
The wave function at t=0 is given by φ(x) = (2/a)^(1/2) sin (πx/a)
It can be calculated that the momentum expectation value p(x) for this wave function is 0. This is also true for all subsequent time periods. If the momentum is calculated with uncertainty, it will be observed that it is unchanging in time, meaning that the uncertainty in the momentum is unchanging in time.
Let us solve the remaining question:
Given that wave function x is normalized and (x) = x, and (p) = Po is constant.
The boost operator can be defined as:
Bq f(x) = eiqx/h f(x), where q is a real number with the appropriate units.
Now, consider a new wave function obtained by boosting the initial wave function:
Vnew(x) = B1 Vo(x).
The expectation value (x)new in the state given by new (x) is:
xnew = [(x)B1 V(x)] / (B1 V(x)) = (x) + q/h
The expectation value (p)new in the state given by new (x) is:
pnew = [(p)B1 V(x)] / (B1 V(x)) = (p) + q
Based on the results, the physical significance of adding an overall factor eiqx/h to a wave function is to displace the position of the wave function by an amount proportional to q/h and the momentum by an amount proportional to q. Hence, this factor represents a uniform motion in the x-direction with
speed v = q/h.(p, B1)
= - iq/h B1, [x, B1]
= h/i B1.
Learn more about uniform motion here
https://brainly.com/question/29029651
#SPJ11
A positive charge q is fixed at point (3,−4)(3,−4) and a negative charge −−q is fixed at point (3,0).(3,0).
Determine the net electric force ⃗ netF→net acting on a negative test charge −−Q at the origin (0,0)(0,0) in terms of the given quantities and physical constants, including the permittivity of free space 0.ε0. Express the force using ij unit vector notation. Enter precise fractions rather than entering their approximate numerical values.
The net electric force acting on a negative test charge at the origin due to a positive charge q and a negative charge -q can be expressed as (-6/πε₀) * j, using ij unit vector notation.
The net electric force acting on a test charge can be calculated by considering the individual electric forces exerted by the charges at their respective positions.
The electric force between two charges is given by Coulomb's Law, which states that the magnitude of the force is proportional to the product of the charges and inversely proportional to the square of the distance between them. The force is also directed along the line connecting the charges.
In this scenario, the positive charge q exerts an electric force on the negative test charge at the origin, while the negative charge -q also exerts an electric force on the test charge. Since the charges have opposite signs, the forces they exert on the test charge will have opposite directions.
The force exerted by the positive charge q can be calculated using Coulomb's Law, considering the distance between the charges. Similarly, the force exerted by the negative charge -q can be calculated using the same formula.
By considering the magnitudes and directions of these forces, and summing them as vectors, the net electric force acting on the negative test charge can be determined. The resulting force can be expressed as (-6/πε₀) * j, where j represents the unit vector in the y-direction. The fraction -6/π arises from the specific values and positions of the charges, while ε₀ represents the permittivity of free space.
Learn more about charge here:
https://brainly.com/question/13871705
#SPJ11
The force on a particle is directed along an x axis and given by F= F₀(x/x₀ - 1) where x is in meters and F is in Newtons. If F₀ = 2.2 N and x₀ = 5.9 m, find the work done by the force in moving the particle from x = 0 to x = 2x₀ m. Number ______________ Units ________________
A 80 kg block is pulled at a constant speed of 3.8 m/s across a horizontal floor by an applied force of 120 N directed 43° above the horizontal. What is the rate at which the force does work on the block? Number ______________ Units ________________
Answer: 1. The work done by the force in moving the particle from x = 0 to x = 2x₀ m is 3.92 J.
2.The rate at which the force does work on the block is 334 W.
1. Finding the work done by the force in moving the particle from x = 0 to x = 2x₀ m
Using the formula, F= F₀(x/x₀ - 1) where x is in meters and F is in Newtons, and given that F₀ = 2.2 N and x₀ = 5.9 m, we can find the work done by the force in moving the particle from x = 0 to x = 2x₀ m.
The work done by the force is equal to the change in kinetic energy. Therefore, the work done by the force in moving the particle from x = 0 to x = 2x₀ m is given by,
W = K₂ - K₁ = (1/2) mv₂² - (1/2) mv₁²
where v₂ and v₁ are the final and initial velocities, respectively, and m is the mass of the particle. In this case, since the force is in the x-direction, we know that the velocity is in the x-direction as well. Therefore, we can use the kinematic equation:
v² - u² = 2as
where v and u are the final and initial velocities, respectively, a is the acceleration, and s is the displacement. We can solve for the final velocity:v = √(u² + 2as)
Using this equation, we can find the final velocity of the particle at
x = 2x₀ m.
We know that the initial velocity is zero since the particle starts from rest. Therefore,
v₂ = √(0 + 2a(2x₀)) = √(4ax₀)
Using the force equation, we can find the acceleration of the particle:
a = F/m = F₀(x/x₀ - 1)/m
Substituting the values of F₀, x₀, and m, we get
a = (2.2 N)(x/5.9 m - 1)/(1 kg) = (2.2 N/m)(x/5.9 - 1)
v₂ = √(4ax₀)
= √(4(2.2 N/m)(2x₀/5.9 - 1)(5.9 m))
= √(17.6(2x₀/5.9 - 1))
= 2.8 m/s
Now, we can find the work done by the force in moving the particle from x = 0 to x = 2x₀ m. We know that the initial velocity is zero, so the initial kinetic energy is zero.
Therefore, W = (1/2) mv₂² = (1/2)(1 kg)(2.8 m/s)² = 3.92 J.
The work done by the force in moving the particle from x = 0 to x = 2x₀ m is 3.92 J.
2. Given that a 80 kg block is pulled at a constant speed of 3.8 m/s across a horizontal floor by an applied force of 120 N directed 43° above the horizontal.
The rate at which the force does work on the block is given by:
P = Fv cosθ
where P is the power, F is the force, v is the velocity, and θ is the angle between F and v. Substituting the values given, we get
P = (120 N)(3.8 m/s) cos 43°
= (120 N)(3.8 m/s)(0.731)
= 334 W.
The rate at which the force does work on the block is 334 W.
Learn more about work done : https://brainly.com/question/25573309
#SPJ11
A capacitor is connected to an AC source. If the maximum current in the circuit is 0.400 A and the voltage from the AC source is given by Av = (82.2 V) sin((601)s-lt], determine the following. (a) the rms voltage (in V) of the source V (b) the frequency (in Hz) of the source Hz (c) the capacitance (in pF) of the capacitor uf
The rms voltage ,Vrms = Imax / √2 = 0.4 A / √2 = 0.283 V.Therefore, the frequency is: f = 1 / T = 1 / 0.0104 s = 96.2 Hz. Therefore, the capacitance of the capacitor is 7.59 pF.
A capacitor is connected to an AC source. If the maximum current in the circuit is 0.400 A and the voltage from the AC source is given by Av = (82.2 V) sin((601)s-lt], the following must be determined.
RMS voltage, V The RMS voltage of the source can be determined using the formula: Vrms = Imax / √2 = 0.4 A / √2 = 0.283 V Frequency, f
The frequency of the source can be determined using the formula: f = 1 / T where T is the period of the wave. Since the voltage is given as Av = (82.2 V) sin((601)s-lt], we can rewrite it as V = Vmax sin(ωt), where Vmax = 82.2 V and ω = 601 s-1.The period of the wave is given by: T = 2π / ω = 2π / (601 s-1) = 0.0104 s
Therefore, the frequency is: f = 1 / T = 1 / 0.0104 s = 96.2 Hz
Capacitance, C The capacitance of the capacitor can be determined using the formula: XC = V / I where XC is the capacitive reactance, V is the voltage, and I is the current.
XC = V / I = 82.2 V / 0.4 A = 205.5 ΩThe capacitive reactance is given by: XC = 1 / (2πfC)where f is the frequency of the source and C is the capacitance of the capacitor.
Rearranging this formula gives: C = 1 / (2πfXC) = 1 / (2π × 96.2 Hz × 205.5 Ω) = 0.00759 µF = 7.59 pF
Therefore, the capacitance of the capacitor is 7.59 pF.
Learn more about capacitance here:
https://brainly.com/question/31871398
#SPJ11
A cord is used to vertically lower an initially staticnary block of mass M = 13 kg at a constant dowrtward acceleration of g/7. When the block has fallen a distance d = 2.4 m, find (a) the work done by the cord's force on the block, (b) the work done by the gravitational force on the block, (c) the kinetic energy of the block, and (d) the speed of the block. (Note: Take the doweward direction positive) (a) Number ________________ Units _________________
(b) Number ________________ Units _________________
(c) Number ________________ Units _________________
(d) Number ________________ Units _________________
(a) The work done by the cord's force on the block is 201.5856J
Number: 201.5856. Units: Joules (J)
(b) The work done by the gravitational force on the block is 306.072 J.
Number: 306.072 . Units: Joules (J)
(c) The kinetic energy of the block is 45.7549
Number: 45.7549 . Units: Joules (J)
(d) The speed of the block is 2.619 m/s.
Number: 2.619. Units: m/s
(a)
Number:
Work done by the cord's force on the block is given by:
W = F × d
The cord's force is equal to the force due to gravity acting on the block minus the force required to give the block an acceleration of g/7.
i.e., Fcord = Mg - Ma
Here,
acceleration of the block, a = g/7
Fcord = Mg - Ma
= 13 × 9.81 - 13 × (9.81/7)
= 13 × 9.81 × 6 / 7
= 83.994 N
Using the formula for work done by the cord's force,
W = Fcord × d
= 83.994 × 2.4
= 201.5856J
Therefore, the work done by the cord's force on the block is 201.5856J.
Units: Joules (J)
(b)
Number:
Work done by the gravitational force on the block is given by:
W = Fg × d
Where, Fg is the force due to gravity acting on the block.
Fg = Mg
= 13 × 9.81
= 127.53 N
Using the formula for work done by the gravitational force,
W = Fg × d
= 127.53 × 2.4
= 306.072 J
Therefore, the work done by the gravitational force on the block is 306.072 J.
Units: Joules (J)
(c)
Number:
The kinetic energy of the block is given by:
K.E. = ½mv²
where, m is the mass of the block, and v is its velocity.
The final velocity of the block can be calculated using the formula:
v² - u² = 2as
where,
u is the initial velocity of the block (which is 0 m/s),
a is the acceleration of the block (which is g/7), and
s is the distance traveled by the block (which is 2.4 m).
v² = 2as
= 2 × (9.81/7) × 2.4
= 6.85714
v = √(6.85714)
= 2.619 m/s
Therefore, the kinetic energy of the block is given by:
K.E. = ½mv²
= ½ × 13 × (2.619)²
= 45.7549 J
Therefore, the kinetic energy of the block is 45.7549
Units: Joules (J)
(d) Number:
The speed of the block is given by:
v² - u² = 2as
v² = 2as
= 2 × (9.81/7) × 2.4
= 6.85714
v = √(6.85714)
= 2.619 m/s
Therefore, the speed of the block is 2.619 m/s.
Units: m/s.
Learn more about the work done:
brainly.com/question/21854305
#SPJ11
A long solenoid with n= 35 turns per centimeter and a radius of R= 12 cm carries a current of i= 35 mA. Find the magnetic field in the solenoid. The magnetci field, Bo 176.6 x Units UT If a straight conductor is positioned along the axis of the solenoid and carries a current of 53 A, what is the magnitude of the net magnetic field at the distance R/2 from the axis of the solenoid? The net magnetic field, Bret = 176.61 Units
Answer:
1) The magnetic field inside the solenoid is approximately 0.0389 Tesla.
2) The magnitude of the net magnetic field at a distance R/2 from the axis of the solenoid is approximately 0.0424 Tesla.
To find the magnetic field inside the solenoid, we can use the formula for the magnetic field inside a solenoid:
B = μ₀ * n * i
Where:
B is the magnetic field
μ₀ is the permeability of free space (4π * 10^(-7) T·m/A)
n is the number of turns per unit length
i is the current
n = 35 turns/cm
= 35 * 100 turns/m
= 3500 turns/m
i = 35 mA
= 35 * 10^(-3) A
Substituting the values into the formula:
B = (4π * 10^(-7) T·m/A) * (3500 turns/m) * (35 * 10^(-3) A)
Calculating:
B ≈ 0.0389 T
Therefore, the magnetic field inside the solenoid is approximately 0.0389 Tesla.
To find the magnitude of the net magnetic field at a distance R/2 from the axis of the solenoid due to the solenoid and the straight conductor, we can sum the magnetic fields produced by each separately.
The magnetic field at a distance R/2 from the axis of the solenoid can be found using the formula:
B_sol = μ₀ * n * i
n = 3500 turns/m
i = 35 * 10^(-3) A
Substituting the values into the formula:
B_sol = (4π * 10^(-7) T·m/A) * (3500 turns/m) * (35 * 10^(-3) A)
Calculating:
B_sol ≈ 0.0389 T
The magnetic field at a distance R/2 from a long straight conductor carrying a current can be found using Ampere's law:
B_conductor = (μ₀ * i) / (2π * R/2)
i = 53 A
R = 12 cm = 0.12 m
Substituting the values into the formula:
B_conductor = (4π * 10^(-7) T·m/A * 53 A) / (2π * 0.12 m)
Calculating:
B_conductor ≈ 0.0035 T
To find the net magnetic field, we can add the magnitudes of the magnetic fields produced by the solenoid and the conductor:
B_net = |B_sol| + |B_conductor|
Substituting the values:
B_net = |0.0389 T| + |0.0035 T|
Calculating:
B_net ≈ 0.0424 T
Therefore, the magnitude of the net magnetic field at a distance R/2 from the axis of the solenoid is approximately 0.0424 Tesla.
Learn more about solenoid, here
https://brainly.com/question/1873362
#SPJ11
a) Mass and inertia are ______ quantities b) Distance is a _____ quantity but displacement is a _____ quantity c) Speed is a _____ quantity but velocity is a _____ quantity, d) Force and torque are _____quantities. e) Momentum is a _____ quantity but energy is a _____ quantity
a) Mass and inertia are scalar quantities.b) Distance is a scalar quantity but displacement is a vector quantity.c) Speed is a scalar quantity but velocity is a vector quantity.d) Force and torque are vector quantities.e) Momentum is a vector quantity but energy is a scalar quantity.
Mass is a scalar quantity that represents the total amount of matter in an object. Mass is frequently referred to as the "m" symbol. Mass is commonly measured in grams, kilograms, or slugs.Inertia is a property of a body that resists any change in motion. Inertia is the resistance of an object to changes in its state of motion. Inertia is a scalar quantity.Distance is the total length traveled by a moving body or the length between two points. Distance is a scalar quantity.Displacement is the shortest distance from the start to the end point of a trip. Displacement is a vector quantity. The difference between the starting and ending positions is known as displacement.The distance traveled by an object per unit time is known as speed. The rate at which an object moves is referred to as its speed. Speed is a scalar quantity.Velocity is the distance traveled by an object per unit time in a specific direction. Velocity is a vector quantity.A force is an influence that causes an object to change its state of motion, velocity, direction, or shape. Force is a vector quantity.Torque is a measure of an object's ability to turn a rotation axis. Torque is a vector quantity.Momentum is the product of an object's mass and velocity. Momentum is a vector quantity.Energy is a scalar quantity that is used to quantify how much work a physical system can perform. The energy in an object is measured in joules (J).
To learn more about inertia visit: https://brainly.com/question/1140505
#SPJ11
A photographer uses his camera, whose lens has a 70 mm focal length, to focus on an object 1.5 m How far must the lens move to focus on this second object? away. He then wants to take a picture of an object that is 40 cm away. Express your answer to two significant figures and include the appropriate un
The lens must move approximately 0.103 meters to focus on the second object, and the distance of the image from the lens when taking a picture of an object that is 40 cm away is approximately 0.046 meters.
To determine the distance the lens must move to focus on the second object, we can use the lens formula:
1/f = 1/u + 1/v,
where f is the focal length of the lens, u is the distance of the first object from the lens (in meters), and v is the distance of the second object from the lens (in meters).
Given that the focal length of the lens is 70 mm, which is equivalent to 0.07 meters, and the distance of the first object is 1.5 meters, we can substitute these values into the formula:
1/0.07 = 1/1.5 + 1/v.
Simplifying this equation gives us:
v = 1 / (1/0.07 - 1/1.5).
Evaluating this expression, we find:
v ≈ 0.103 meters.
Therefore, the lens must move approximately 0.103 meters to focus on the second object.
For taking a picture of an object that is 40 cm away, we can use the same lens formula:
1/f = 1/u + 1/v,
where u is the distance of the object from the lens (in meters) and v is the distance of the image from the lens (also in meters).
Given that the focal length of the lens is 0.07 meters, we can substitute the values into the formula:
1/0.07 = 1/0.4 + 1/v.
Simplifying this equation gives us:
v = 1 / (1/0.07 - 1/0.4).
Evaluating this expression, we find:
v ≈ 0.046 meters.
Therefore, the distance of the image from the lens when taking a picture of an object that is 40 cm away is approximately 0.046 meters.
In summary, the lens must move approximately 0.103 meters to focus on the second object, and the distance of the image from the lens when taking a picture of an object that is 40 cm away is approximately 0.046 meters.
Learn more about focal length here:
https://brainly.com/question/31755962
#SPJ11
A 1.40-m-long metal bar is pulled to the right at a steady 4.8 m/s perpendicular to a uniform, 0.715-T magnetic field. The bar rides on parallel metal rails connected through R=25.8−Ω, as shown in the figure, so the apparatus makes a complete circuit. You can ignore the resistance of the bar and the rails. Calculate the magnitude of the emf induced in the circuit. 4,8 V 0.186 V 2,45 V 124 V
The magnitude of the emf induced in the circuit is 124 V.
When a metal bar is pulled at a steady rate through a magnetic field, an electromotive force (emf) is induced. This emf is caused by a change in the magnetic flux that passes through the circuit that the bar is a part of.
According to Faraday’s law, the magnitude of this induced emf is equal to the rate of change of the magnetic flux, or emf=−NΔΦΔt, where N is the number of turns in the circuit, and ΔΦΔt is the rate of change of the magnetic flux that passes through each turn of the circuit. In this case, the bar is being pulled through a uniform magnetic field of 0.715 T at a steady rate of 4.8 m/s.
The magnetic flux that passes through the circuit is then equal to BAh, where A is the area of each turn of the circuit, h is the height of each turn of the circuit, and B is the strength of the magnetic field. Since the bar is moving perpendicular to the magnetic field, the area of each turn of the circuit that the bar moves through is simply equal to the length of the bar times the height of each turn.
Therefore, A=1.40m×h. The rate of change of the magnetic flux is then equal to BAdhdt, where dhdt is the rate at which the bar is moving through the circuit.
Therefore, emf=−NABdhdt=−NABv. In this case, the bar is connected to parallel metal rails connected through R=25.8Ω, which form a complete circuit.
The induced emf then drives a current I=emfR through this circuit. Since the resistance of the bar and the rails is ignored, the induced emf is simply equal to the voltage across the resistance R, or emf=IR.
Therefore, emf=I(R)=−NABvR.
Substituting the given values, we have emf=−1×0.715×(1.40m×h)×4.8ms−1×25.8Ω=−124V.
Hence the magnitude of the emf induced in the circuit is 124 V.
Know more about Faraday’s law here,
https://brainly.com/question/33343234
#SPJ11