When Sub B is at rest (vB=0), an observer on Sub B will detect the frequency of the sonar wave emitted by Sub A to be 1000 Hz, the same as the emitted frequency.
When Sub B is moving to the right with a speed of vB=12 m/s, an observer on Sub B will detect a Doppler-shifted frequency of approximately 956.5 Hz. This frequency is lower than the emitted frequency due to the relative motion between the two submarines.
When the sonar signal emitted by Sub A bounces off Sub B and reflects back, an observer on Sub A will detect a frequency of approximately 1050 Hz. This frequency is higher than the emitted frequency due to the Doppler effect caused by the motion of Sub B.
When Sub B is at rest, the observed frequency is the same as the emitted frequency. The motion of Sub A does not affect the frequency detected by an observer on Sub B since the observer is stationary with respect to the water. Therefore, the frequency detected by the observer on Sub B is 1000 Hz, the same as the emitted frequency.
When Sub B is moving to the right with a speed of vB=12 m/s, there is relative motion between Sub A and Sub B. This relative motion causes a Doppler shift in the frequency of the sonar wave detected by an observer on Sub B. The Doppler formula for frequency shift is given by:
f' = f * (v_sound + v_observer) / (v_sound + v_source)
Where:
f' is the detected frequency,
f is the emitted frequency,
v_sound is the speed of sound in water (1500 m/s),
v_observer is the velocity of the observer (Sub B),
v_source is the velocity of the source (Sub A).Plugging in the values, we get:
f' = 1000 Hz * (1500 m/s + 12 m/s) / (1500 m/s + 8 m/s) ≈ 956.5 Hz Therefore, the frequency detected by an observer on Sub B is approximately 956.5 Hz.
Learn more about Doppler effect click here: brainly.com/question/28106478
#SPJ11
Transcribed image text: A rotating fan completes 1150 revolutions every minute. Consider the tip of the blade, at a radius of 120 cm. What is the linear distance moved when the tip moves through one revolution? What is the tip's speed and the magnitude of its acceleration? What is the period of the motion? Sebuah kipas yang berputar membuat 1150 putaran lengkap seminit. Pertimbangkan hujung bilah kipas, pada jejari 120 cm Berapakah jarak yang dibuat oleh hujung bilah kipas di dalam sutu putaran? Berapakah laju dan magnitud pecutan hujung bilah kipas? Berapakah tempoh gerakan? [16 marks / 16 markah] (a Light from a helium-neon laser (630 nm) is incident on a pair of slits. Interference pattern can be seen on a screen 2.0 m from the slits and the bright fringes are separated by 1.40 cm. What is the slit separation? A grating has 5000 lines per cm. Determine the angular separation between the central maximum and the second-order bright fringe if the wavelength of violet light is 410 nm. (b) (a) Cahaya dari helium-neon laser (630 nm) melalui sepasang celahan. Corak interferens dapat dilihat pada layar yang jauhnya 2.0 m dari celahan dan pinggir-pinggir terang dipisahkan sejauh 1.40 cm. Berapakah jarak pisahan antara celahan? Satu parutan mempunyai 5000 garisan per cm. Tentukan sudut pemisahan di antara pinggir terang pusat dengan pinggir terang tertib kedua jika panjang gelombang cahaya ungu ialah 410 nm. [16 marks / 16 markah] (b)
When the rotating fan completes one revolution, the tip of the blade moves a linear distance equal to the circumference of a circle with a radius of 120 cm. The tip's speed is the linear distance moved per unit of time, and its acceleration can be calculated using the formula for centripetal acceleration. The period of motion is the time taken for one complete revolution.
To find the linear distance moved by the tip of the blade in one revolution, we can use the formula for the circumference of a circle: C = 2πr, where r is the radius. Substituting the given radius of 120 cm, we have C = 2π(120 cm) = 240π cm.
The tip's speed is the linear distance moved per unit of time. Since the fan completes 1150 revolutions per minute, we can calculate the speed by multiplying the linear distance moved in one revolution by the number of revolutions per minute and converting to a consistent unit. Let's convert minutes to seconds by dividing by 60:
Speed = (240π cm/rev) * (1150 rev/min) * (1 min/60 s) = 4600π/3 cm/s.
To find the magnitude of the tip's acceleration, we can use the formula for centripetal acceleration: a = v²/r, where v is the speed and r is the radius. Substituting the given values, we have:
Acceleration = (4600π/3 cm/s)² / (120 cm) = 211200π²/9 cm/s².
The period of motion is the time taken for one complete revolution. Since the fan completes 1150 revolutions per minute, we can calculate the period by dividing the total time in minutes by the number of revolutions:
Period = (1 min)/(1150 rev/min) = 1/1150 min/rev.
In summary, when the fan completes one revolution, the tip of the blade moves a linear distance of 240π cm. The tip's speed is 4600π/3 cm/s, and the magnitude of its acceleration is 211200π²/9 cm/s². The period of motion is 1/1150 min/rev.
To know more about centripetal acceleration refer here:
https://brainly.com/question/32812920#
#SPJ11
QUESTION 2 Which ruler is the least accurate? 20 20 20 10 10 10 0 0 0 B. A с 20 -20 20 10 10 10 A B 0 A&B B&C A & C None of them accurate All of them same accuracy Not enough information to decide СО
From the given terms, the ruler that is the least accurate can be determined by the ruler that is different from the other rulers.
To determine this, let us observe the rulers given.
20 20 2010 10 100 0 0B.
A с20 -20 2010 10 10A B0
A&B B&C A & C None of them accurate
All of them same accuracy
Not enough information to decide
From the given terms, it can be observed that ruler B is the least accurate as it is not the same as the other rulers and shows a negative value of -20 while all the other rulers show positive values or 0.
Thus, option B is the correct answer.
To know more about positive visit:
https://brainly.com/question/23709550
#SPJ11
"Earth's average surface temperature is about 287 K. Assuming
Earth radiates as a blackbody, calculate max (in m) for
the Earth.
The wavelength corresponding to the maximum intensity (Amax) of radiation emitted by the Earth as a blackbody is approximately 1.01 x 10^-5 meters (m), assuming an average surface temperature of 287 K.
To calculate the wavelength corresponding to the maximum intensity (Amax) of radiation emitted by the Earth as a blackbody, we can use Wien's displacement law. According to the law:
Amax = (b / T),
where:
Amax is the wavelength corresponding to the maximum intensity,b is Wien's displacement constant (approximately 2.898 x 10^-3 m·K),T is the temperature in Kelvin.Substituting the given values:
T = 287 K,
we can calculate Amax:
Amax = (2.898 x 10^-3 m·K) / (287 K).
Amax ≈ 1.01 x 10^-5 m.
Therefore, the wavelength corresponding to the maximum intensity (Amax) of radiation emitted by the Earth as a blackbody is approximately 1.01 x 10^-5 meters (m).
To learn more about Wien's displacement law, Visit:
https://brainly.com/question/28365925
#SPJ11
Captain Proton confronts the flatulent yet eerily floral Doctor Yango in his throne room. Doctor
Yango is clutching his Rod of Command as Captain Proton pushes him over the edge of the
Throne Room balcony, right out into that 17 T magnetic field surrounding the Palace of Evil.
Doctor Yango activates his emergency escape rocket and flies off at 89.7 m/s. Assuming that the
Rod is conductive, 0.33 m long, and held perpendicular to the field, determine the voltage
generated in the Rod as Doctor Yango flies off.
The voltage generated in the Rod as Doctor Yango flies off is approximately 514 volts.
As we know, the voltage induced in a conductor moving through a magnetic field is given by this formula;
v = Bl
voltage induced = magnetic field × length of conductor × velocity
Now, substituting the values given in the question;
v = (17 T) (0.33 m) (89.7 m/s) = 514 T⋅m/s ≈ 514 V
Therefore, the voltage generated in the Rod as Doctor Yango flies off is approximately 514 volts.
To learn more about voltage
https://brainly.com/question/1176850
#SPJ11
A drag racer reaches a speed of 147 m/s [N] over a distance of 400 m. Calculate the average force applied by the engine if the mass of the car and the drag racer is 850 kg.
The average force applied by the engine if the mass of the car and the drag racer is 850 kg is approximately 22,950 Newtons.
To calculate the average force applied by the engine, we can use Newton's second law of motion, which states that the force (F) is equal to the mass (m) multiplied by the acceleration (a):
F = m × a
In this case, the acceleration can be calculated using the equation for average acceleration:
a = (final velocity - initial velocity) / time
The equation of motion to calculate time is:
distance = (initial velocity × time) + (0.5 × acceleration × time²)
We know the distance (400 m), initial velocity (0 m/s), and final velocity (147 m/s). We can rearrange the equation to solve for time:
400 = 0.5 × a × t²
Substituting the given values, we have:
400 = 0.5 × a × t²
Using the formula for average acceleration:
a = (final velocity - initial velocity) / time
a = (147 - 0) / t
Substituting this into the distance equation:
400 = 0.5 × [(147 - 0) / t] × t²
Simplifying the equation:
400 = 0.5 × 147 × t
800 = 147 × t
t = 800 / 147
t = 5.4422 seconds (approximately)
Now that we have the time, we can calculate the average acceleration:
a = (final velocity - initial velocity) / time
a = (147 - 0) / 5.4422
a ≈ 27 m/s² (approximately)
Finally, we can calculate the average force applied by the engine using Newton's second law:
F = m × a
F = 850 kg × 27 m/s²
F = 22,950 N (approximately)
Learn more about force -
brainly.com/question/12785175
#SPJ11
A standing wave on a string is described by the wave function y(xt) - (3 mm) sin(4rtx\cos(30nt). The wave functions of the two waves that interfere to produce this standing wave pattern are:
A standing wave on a string is described by the wave function y(xt) - (3 mm) sin(4rtx\cos(30nt). he wave functions of the two waves that interfere to produce the given standing wave pattern are:
y1(x,t) = (3 mm) sin(4πx) cos(30πt),y2(x,t) = (3 mm) sin(4πx) cos(30πt + π)
To determine the wave functions of the two waves that interfere to produce the given standing wave pattern, we need to analyze the properties of standing waves.
The given standing wave function is y(x,t) = (3 mm) sin(4πx) cos(30πt).
In a standing wave on a string, the interference of two waves traveling in opposite directions creates the standing wave pattern. The wave functions of the two interfering waves can be obtained by considering the components of the standing wave function.
Let's denote the wave functions of the two interfering waves as y1(x,t) and y2(x,t).
The general equation for a standing wave on a string is given by y(x,t) = A sin(kx) cos(ωt), where A is the amplitude, k is the wave number, x is the position along the string, and ω is the angular frequency.
Comparing this with the given standing wave function, we can deduce the wave functions of the two interfering waves:
y1(x,t) = (3 mm) sin(4πx) cos(30πt)
y2(x,t) = (3 mm) sin(4πx) cos(30πt + π)
Therefore, the wave functions of the two waves that interfere to produce the given standing wave pattern are:
y1(x,t) = (3 mm) sin(4πx) cos(30πt)
y2(x,t) = (3 mm) sin(4πx) cos(30πt + π)
To learn more about wave functions visit: https://brainly.com/question/30591309
#SPJ11
A bar is pulled to the right in the circuit shown below. The magnetic field is constant, going into the page /screen. As viewed, the induced current through the resistor will: be zero flow downward oscilate back and forth How unward
When a bar is pulled to the right in the circuit shown below with a constant magnetic field going into the screen, the induced current through the resistor will oscillate back and forth.
An induced emf is generated in the conductor by a magnetic field that changes in time. Faraday's law of induction is the principle that governs this behaviour. The induced current through the resistor will therefore oscillate back and forth when the magnetic flux that penetrates a closed circuit changes with time (i.e., the flux linking the coil in the circuit shown below changes as the bar moves).
This back and forth oscillation is due to the fact that as the bar moves to the right and out of the magnetic field, the current flows upwards. However, as the bar moves to the left and into the magnetic field, the current flows downwards. This results in the induced current oscillating back and forth through the resistor.
To know more about conductor visit:
https://brainly.com/question/14405035
#SPJ11
A man holds a 2kg watermelon above his head 1.8m above the ground. He holds the watermelon steady so it is not moving. How much work is done by the man as he is holding the watermelon?
The man does approximately 35.28 Joules of work while holding the watermelon steady above his head.
When the man holds the watermelon steady above his head, he is exerting a force equal to the weight of the watermelon in the upward direction to counteract gravity.
The work done by the man can be calculated using the formula:
Work = Force × Distance × cosθ
Where:
Force is the upward force exerted by the man (equal to the weight of the watermelon),
Distance is the vertical distance the watermelon is lifted (1.8 m),
θ is the angle between the force and the displacement vectors (which is 0 degrees in this case, since the force and displacement are in the same direction).
Mass of the watermelon (m) = 2 kg
Acceleration due to gravity (g) = 9.8 m/s^2
Distance (d) = 1.8 m
Weight of the watermelon (Force) = mass × gravity
Force = 2 kg × 9.8 m/s^2
Force = 19.6 N
Now we can calculate the work done by the man:
Work = Force × Distance × cosθ
Work = 19.6 N × 1.8 m × cos(0°)
Work = 19.6 N × 1.8 m × 1
Work = 35.28 Joules
Learn more about work -
brainly.com/question/14813637
#SPJ11
: A square of bamboo skewers of side length 0.25 m has point charges of +8.5 nanoCoulombs each corner. (20, 10 each) a. At the bottom left hand corner, what is the electric field due to the other three charges? b. At the top left hand corner, what is the electric potential of this charge from the other three charges?
The electric field at a point due to a point charge can be calculated using Coulomb's law: E = k*q/r^2. The electric potential due to a point charge can be calculated using the equation V = k*q/r
a. The electric field at the bottom left-hand corner of the square of bamboo skewers can be determined by calculating the vector sum of the electric fields produced by the other three charges. Each corner charge of +8.5 nano Coulombs generates an electric field that points away from it. Since the charges are positive, the electric fields will be radially outward. To calculate the electric field at the bottom left-hand corner, we need to consider the contributions from the charges at the bottom right, top left, and top right corners. The electric field at a point due to a point charge can be calculated using Coulomb's law: E = k*q/r^2, where E is the electric field, k is the electrostatic constant (8.99 x 10^9 Nm^2/C^2), q is the charge, and r is the distance between the charge and the point of interest.
b. The electric potential at the top left-hand corner of the square of bamboo skewers due to the other three charges can be determined by calculating the scalar sum of the electric potentials produced by each charge. Electric potential is a scalar quantity that represents the amount of work needed to bring a unit positive charge from infinity to a specific point in an electric field. The electric potential due to a point charge can be calculated using the equation V = k*q/r, where V is the electric potential, k is the electrostatic constant, q is the charge, and r is the distance between the charge and the point of interest.
By summing the electric potentials contributed by the charges at the bottom right, top left, and top right corners, we can determine the electric potential at the top left-hand corner of the square.
Learn more about charge here:
brainly.com/question/13871705
#SPJ11
Suppose that 2,219 J of heat transfers from a large object that maintains a temperature of 46.0° C into its environment that has
a constant temperature of 21.0° C. What overall entropy increase occurs as a result of this heat transfer assuming the temperatures
of the object and the environment are constant? Express your answer to three significant figures in joules per kelvin.
The overall entropy increase resulting from the heat transfer is 72.3 J/K.
Entropy is a measure of the degree of disorder or randomness in a system. In this case, the heat transfer occurs between a large object and its environment, with constant temperatures of 46.0°C and 21.0°C, respectively. The entropy change can be calculated using the formula:
ΔS = Q / T
where ΔS is the change in entropy, Q is the heat transferred, and T is the temperature in Kelvin.
Given that the heat transferred is 2,219 J and the temperatures are constant, we can substitute these values into the equation:
ΔS = 2,219 J / 46.0 K = 72.3 J/K
Therefore, the overall entropy increase as a result of the heat transfer is 72.3 J/K. This value represents the increase in disorder or randomness in the system due to the heat transfer at constant temperatures.
To learn more about entropy , click here : https://brainly.com/question/32070225
#SPJ11
Which has more kinetic energy: a 0,0013-kg bullet traveling at 411 m/s or a 5.7 x 107-kg ocean liner traveling at 10 m/s (19 knots)? O the bullet has greater kinetic energy O the ocean liner has greater kinetic energy Justify your answer. Ex-bullet -ocean liner
To determine which has more kinetic energy between a 0.0013 kg bullet traveling at 411 m/s and a 5.7 x 10^7 kg ocean liner traveling at 10 m/s, we compare their kinetic energies.
Kinetic energy formula: The kinetic energy (KE) of an object is given by the equation KE = 0.5 * m * v^2, where m is the mass of the object and v is its velocity.
Calculation for the bullet:
KE_bullet = 0.5 * (0.0013 kg) * (411 m/s)^2
Calculation for the ocean liner:
KE_ocean liner = 0.5 * (5.7 x 10^7 kg) * (10 m/s)^2
To learn more about kinetic energy click here.
brainly.com/question/999862
#SPJ11
When a potential difference of 12 V is applied to a wire 7.2 m long and 0.34 ram in diameter the result is an electric
current of 2.0 A. What is the resistivity of the wire?
The resistivity of the wire is approximately 3.03 x 10^-6 Ω·m.
To determine the resistivity of the wire, we can use Ohm's Law, which states that the current (I) flowing through a conductor is directly proportional to the applied voltage (V) and inversely proportional to the resistance (R).
Resistance (R) can be calculated using the formula R = (ρ * L) / A, where ρ is the resistivity of the material, L is the length of the wire, and A is the cross-sectional area of the wire.
Given:
Potential difference (V) = 12 V
Length of the wire (L) = 7.2 m
Diameter of the wire (d) = 0.34 cm (which can be converted to meters as 0.0034 m)
First, we need to calculate the cross-sectional area (A) of the wire using the formula A = π * (d/2)^2:
A = π * (0.0034 m/2)^2 = 3.628 x 10^-6 m^2
Next, rearrange Ohm's Law to solve for resistance (R):
R = V / I = 12 V / 2.0 A = 6 Ω
Now, substitute the values of R, L, and A into the resistance formula to solve for resistivity (ρ):
6 Ω = (ρ * 7.2 m) / 3.628 x 10^-6 m^2
ρ = (6 Ω * 3.628 x 10^-6 m^2) / 7.2 m
ρ ≈ 3.03 x 10^-6 Ω·m
Therefore, the resistivity of the wire is approximately 3.03 x 10^-6 Ω·m.
Learn more about resistivity here:
https://brainly.com/question/23631582
#SPJJ11
Twins A and B are both 19.0 years old when twin B decides to embark on a space voyage. Twin B blasts off from Earth and travels at a speed of 0.97c. Twin A remains on Earth, and after waiting 35.0 years, twin A is reunited with twin B, who has returned from the space voyage. Twin A is now 54.0 years old. How old is twin B?
ΔT = ΔT0 / (1 - v^2/c^2)^1/2
ΔT is the time elapsed in the moving frame and ΔT0 is the proper time that has elapsed in the frame where the clock is stationary
ΔT = 35 years which is the elapsed time in frame A - age of twin in that frame
ΔT0 = 35 * (1 - .97^2) = 2.07 yrs time elapsed for twin (B) in stationary frame B - measured WRT a clock at a single point
the proper time in frame B will be the actual elapsed time (age) that has passed in that frame - frame A is moving WRT frame (B)
.A car and a truck collide head-on a) Will the force be greatest on the car, the .truck, or the same on both? Motivate b) Which of the drivers is exposed to the greatest acceleration? Motivate
A head-on collision between a car and a truck is a type of accident that can cause a significant amount of damage and injuries. The force that is generated in this type of accident depends on the mass of the vehicles involved.
In this case, the truck has a greater mass compared to the car, which means that it will generate more force during the collision. The force will be greater on the car than the truck because the car has less mass compared to the truck.Both drivers are exposed to the same acceleration during the collision. This is because the acceleration that a driver is exposed to during a collision depends on the force generated during the collision and the mass of the driver. Since both drivers have the same mass, they will be exposed to the same acceleration during the collision.
The driver of the car will experience a greater force due to the impact of the collision, which can result in more severe injuries compared to the driver of the truck.In conclusion, during a head-on collision between a car and a truck, the force will be greater on the car compared to the truck. However, both drivers will be exposed to the same acceleration during the collision.
To know more about acceleration visit:
https://brainly.com/question/12550364
#SPJ11
A 0.40 kg mass is attached to a spring with a force constant of k-307 N/m, and the mass spring system is set into oscillation with an amplitude of A2.3 cm. Determine the following (a) mechanical energy of the system (b) maximum speed of the Oscillating mass m/s (c) magnitude of the maximum acceleration of the oscillating mass m/s?
The maximum speed of the oscillating mass is approximately 0.635 m/s. the magnitude of the maximum acceleration of the oscillating mass is approximately 18.71 m/s².
(a) To determine the mechanical energy of the system, we need to consider both the potential energy and the kinetic energy.
The potential energy (PE) of a mass-spring system is given by:
[tex]PE = (1/2) * k * A^2[/tex]
where:
k is the force constant of the spring,
A is the amplitude of the oscillation.
Substituting the given values:
k = 307 N/m
A = 2.3 cm = 0.023 m
[tex]PE = (1/2) * 307 N/m * (0.023 m)^2[/tex]
Calculating the value, we get:
[tex]PE ≈ 0.00258 J[/tex]
The kinetic energy (KE) of the system can be determined using the equation:
[tex]KE = (1/2) * m * v^2[/tex]
where:
m is the mass,
v is the velocity.
Since the mass is given as 0.40 kg, we can calculate the kinetic energy once we determine the maximum velocity (v).
(b) To find the maximum velocity of the oscillating mass, we can use the equation:
[tex]v = ω * A[/tex]
where:
ω is the angular frequency,
A is the amplitude of the oscillation.
The angular frequency (ω) can be calculated using the formula:
ω = √(k / m)
Substituting the given values:
k = 307 N/m
m = 0.40 kg
[tex]ω = √(307 N/m / 0.40 kg)[/tex]
Calculating the value, we get:
ω ≈ 27.62 rad/s
Now we can calculate the maximum velocity (v):
v = ω * A
Substituting the values:
v = 27.62 rad/s * 0.023 m
Calculating the value, we get:
v ≈ 0.635 m/s
Therefore, the maximum speed of the oscillating mass is approximately 0.635 m/s.
(c) The magnitude of the maximum acceleration of the oscillating mass can be determined using the equation:
[tex]a = ω^2 * A[/tex]
where:
ω is the angular frequency,
A is the amplitude of the oscillation.
Using the previously calculated value of ω ≈ 27.62 rad/s and the given value of A = 0.023 m, we can calculate the acceleration (a):
[tex]a = (27.62 rad/s)^2 * 0.023 m[/tex]
Calculating the value, we get:
[tex]a ≈ 18.71 m/s²[/tex]
Therefore, the magnitude of the maximum acceleration of the oscillating mass is approximately 18.71 m/s².
Learn more about mechanical energy from the given link
https://brainly.com/question/30403434
#SPJ11
Which graphs could represent the Position versus Time for CONSTANT ACCELERATION MOTION
The acceleration motion, the position versus time graphs are: Linear graph, Quadratic graph, position-time graph.
Linear graph: The position-time graph could be a straight line with a slope. The slope reflects velocity, and the line's curvature indicates constant acceleration.
Quadratic graph: A concave-up parabolic curve could be the position-time graph. With steady acceleration, the curve shows position change.
Position-time graph: The position-time graph might be a cubic curve with a stronger curvature. With steady acceleration, the curve shows position change.
The graph's shape depends on beginning conditions like position, velocity, and acceleration. Position-time graphs for constant acceleration motion are shown in the three cases.
A positive-slope linear graph.
Concave-up quadratic graph.
Graph with constant positive slope and horizontal line.
Graph with horizontal line and steady positive slope.
These graphs indicate constant accelerating motion since their position changes over time.
To knnow more about acceleration
https://brainly.com/question/460763
#SPJ4
Position versus Time graphs for constant acceleration motion can be represented in the following ways: a straight line, a curved line, an upward sloping parabola and a downward sloping parabola
A straight line that is inclined at an angle to the horizontal axis indicates an object moving at a constant acceleration with a positive slope.A curved line that forms a parabolic arc represents an object with constant acceleration (not equal to zero).An upward sloping parabola depicts an object with constant and positive acceleration.A downward sloping parabola represents an object with constant and negative acceleration.Learn more about Time graphs:
https://brainly.com/question/32254104
#SPJ11
What is the percent error of if you determined the value of to be 3.14 compared with the accepted value of 3.142?
The percent error when the measured value is 3.14 compared to the accepted value of 3.142 is approximately 0.063626%.
To calculate the percent error, you can use the formula:
Percent Error = (|Measured Value - Accepted Value| / Accepted Value) * 100
In this case, the measured value is 3.14 and the accepted value is 3.142. Plugging these values into the formula, we get:
Percent Error = (|3.14 - 3.142| / 3.142) 100
Simplifying the equation:
Percent Error = (0.002 / 3.142) 100
Dividing 0.002 by 3.142:
Percent Error = 0.00063626 * 100
Multiplying by 100:
Percent Error = 0.063626%
Therefore, the percent error when the measured value is 3.14 compared to the accepted value of 3.142 is approximately 0.063626%.
The percent error is very small, indicating that the measured value is very close to the accepted value.
To know more about Percent visit:
brainly.com/question/32354884
#SPJ11
what is the force of gravitational attraction between a ball with
mass 86kg and hand with mass 4.4 kg given they are .57m away from
each other
The force of gravitational attraction between the ball and the hand is approximately 2.6348 x 10^-7 Newtons.
To calculate the force of gravitational attraction between the ball and the hand, we can use the formula:
F = (G * m1 * m2) / r^2
where F is the force of gravitational attraction, G is the gravitational constant (approximately 6.67430 x 10^-11 N*m^2/kg^2), m1 is the mass of the ball (86 kg), m2 is the mass of the hand (4.4 kg), and r is the distance between them (0.57 m).
Plugging in the values, we get:
F = (6.67430 x 10^-11 N*m^2/kg^2 * 86 kg * 4.4 kg) / (0.57 m)^2
Calculating this expression gives us:
F = 2.6348 x 10^-7 N
Therefore, the force of gravitational attraction between the ball and the hand is approximately 2.6348 x 10^-7 Newtons.
Learn more about gravitational attraction: https://brainly.com/question/15090289
#SPJ11
A compact disk (CD) rotates at high speed while a laser reads data encoded in a spiral pattern. The disk has radius R = 6.0 cm; when data are being read, it spins at 7200 rev/min. A) What is the CD's angular velocity in radians per second? B) How much time is required for it to rotate through 120°? C) If it starts from rest and reaches full speed in 3.0 s, what is its average angular acceleration? D) What is the final linear velocity at the edge of the compact dise?
The CD's angular velocity is 4π rad/s. it takes (2/3) seconds for the CD to rotate through 120°. The average angular acceleration of the CD is (4π/3) rad/s². The final linear velocity at the edge of the compact disk is 0.24π m/s.
A) The CD's angular velocity in radians per second:
Given:
Radius of the CD, R = 6.0 cm = 0.06 m
Rotational speed, n = 7200 rev/min
Angular velocity (ω) = 2πn/60 = 240π rad/min
Angular velocity (ω) = (240π)/60 = 4π rad/s
Therefore, the CD's angular velocity is 4π rad/s.
B) The time required for the CD to rotate through 120°:
Given:
Angle of rotation, θ = 120° = 120(π/180) rad
Angular velocity, ω = 4π rad/s
t = θ/ω
t = (120π/180) / (4π) = (2/3) s
Therefore, it takes (2/3) seconds for the CD to rotate through 120°.
C) The average angular acceleration of the CD:
Given:
Initial angular velocity, ω(initial) = 0 rad/s
Final angular velocity, ω(final) = 4π rad/s
Time, t = 3.0 s
α(average) = ω(final) - ω(initial) / t
α(average) = (4π - 0) / 3.0 = 4π/3 rad/s²
Therefore, the average angular acceleration of the CD is (4π/3) rad/s².
D) The final linear velocity at the edge of the CD:
Given:
Radius of the CD, R = 6.0 cm = 0.06 m
Angular velocity, ω = 4π rad/s
v = Rω
v = (0.06)(4π) = 0.24π m/s
Therefore, the final linear velocity at the edge of the compact disk is 0.24π m/s.
To know more about angular acceleration and velocity:
https://brainly.com/question/1980605
#SPJ4
What is the angular momentum LA if rA = 4, −6, 0 m and p = 11,
15, 0 kg · m/s? (Express your answer in vector form.)
The angular momentum LA if rA = 4, −6, 0 m and p = 11,15, 0 kg · m/s is LA= (-90i+44j+15k) kg.m^2/s.
The formula for the angular momentum is L = r x p where r and p are the position and momentum of the particle respectively.
We can write the given values as follows:
rA = 4i - 6j + 0k (in m)
p = 11i + 15j + 0k (in kg.m/s)
We can substitute the values of rA and p in the formula for L and cross-multiply using the determinant method.
Therefore, L = r x p = i j k 4 -6 0 11 15 0 = (-90i + 44j + 15k) kg.m^2/s where i, j, and k are unit vectors along the x, y, and z axes respectively.
Thus, the angular momentum LA is (-90i+44j+15k) kg.m^2/s in vector form.
Learn more about angular momentum here:
https://brainly.com/question/29897173
#SPJ11
An electron experiences a downward magnetic force of 7.00×10 −14 N when it is travelling at 1.8×10 5 m/s south through a magnetic field. Calculate the magnitude and direction of the magnetic field. a. 1.6⊤ down b. 4.3×10 11 T down C. 2.3×10 8 ⊤ down d. 2.4 T down A charged particle is travelling west through a downward magnetic field and it experiences a magnetic force directed to the north. Using the appropriate hand rule, determine if the charge is negative or positive. Explain all finger directions and the palm direction. Calculate the magnitude and the direction of the magnetic force acting on an alpha particle that is travelling upwards at a speed of 3.00×10 5 m/s through a 0.525 T west magnetic field. Explain all finger directions and the palm direction.
The magnitude of the magnetic field is approximately 2.430 T, and it is directed downward.The magnitude of the magnetic force acting on the alpha particle is approximately 3.15 × 10⁵N, and it is directed north, based on the right-hand rule.
To calculate the magnitude and direction of the magnetic field in the first scenario:
Force on the electron (F) = 7.00 × 10⁽⁻¹⁴⁾ N,
Velocity of the electron (v) = 1.8 × 10⁵ m/s.
The formula for the magnetic force on a charged particle moving through a magnetic field is given by:
F = qvB sin(θ),
where F is the force, q is the charge of the particle, v is the velocity, B is the magnetic field strength, and θ is the angle between the velocity vector and the magnetic field vector.
In this case, the force is downward, the velocity is south, and the angle is 90 degrees (because the velocity is perpendicular to the force). Therefore, sin(θ) = 1.
Rearranging the formula, we can solve for the magnetic field strength (B):
B = F / (qv).
Substituting the given values:
B = (7.00 × 10⁽⁻¹⁴⁾ N) / (1.6 × 10⁽⁻¹⁹⁾⁾ C × 1.8 × 10⁵ m/s).
B = 2.430 T.
For the second scenario, using the appropriate hand rule:
When a charged particle is moving in a magnetic field, the thumb points in the direction of the force, the index finger points in the direction of the magnetic field, and the middle finger points in the direction of the velocity.
If the magnetic force is directed to the north and the velocity of the particle is west, then the magnetic field must be directed upward. Since the force is directed opposite to the velocity, the charge of the particle must be negative.
Regarding the calculation of the magnitude and direction of the magnetic force acting on an alpha particle:
Velocity of the alpha particle (v) = 3.00 × 10⁵m/s,
Magnetic field strength (B) = 0.525 T.
Using the formula:
F = qvB sin(θ),
where F is the force, q is the charge of the particle, v is the velocity, B is the magnetic field strength, and θ is the angle between the velocity vector and the magnetic field vector.
Since the alpha particle is traveling upward, and the magnetic field is west, the angle θ is 90 degrees. Therefore, sin(θ) = 1.
Substituting the given values into the formula:
F = (2e)(3.00 × 10⁵ m/s)(0.525 T)(1).
F = 3.15 × 10⁵ N.
To know more about magnetic field refer here
brainly.com/question/30331791
#SPJ11
A Rankine steam power plant produces 0.5 MW of mechanical power by expanding steam
from 60 bar, 700 C, to 3 bar. The efficiency of the turbine and of the pump is 80%. Calculate the energy
balances, determine the flow rate of steam, and determine the entropy generation in each unit. Assume the
condenser produces saturated liquid.
The flow rate of steam in the Rankine steam power plant is approximately 0.075 kg/s, and the entropy generation in the turbine and pump is 0.232 kW/K and 0.298 kW/K, respectively.
In order to determine the flow rate of steam in the Rankine steam power plant, we can start by calculating the heat input and heat output. The heat input to the turbine is given by the difference in enthalpy between the inlet and outlet conditions of the turbine:
Q_in = m_dot * (h_1 - h_2)
Where m_dot is the mass flow rate of steam, h_1 is the specific enthalpy at the turbine inlet (60 bar, 700°C), and h_2 is the specific enthalpy at the turbine outlet (3 bar). Given the efficiency of the turbine (80%), we can write:
Q_in = W_turbine / η_turbine
Where W_turbine is the mechanical power output of the turbine (0.5 MW). Rearranging the equation, we have:
m_dot = (W_turbine / η_turbine) / (h_1 - h_2)
Substituting the given values, we can calculate the flow rate of steam:
m_dot = (0.5 MW / 0.8) / ((h_1 - h_2))
To determine the entropy generation in each unit, we can use the isentropic efficiency of the pump (80%). The isentropic efficiency is defined as the ratio of the actual work done by the pump to the work done in an ideal isentropic process:
η_pump = W_actual_pump / W_ideal_pump
The actual work done by the pump can be calculated using the equation
W_actual_pump = m_dot * (h_4 - h_3)
Where h_3 is the specific enthalpy at the pump outlet (3 bar) and h_4 is the specific enthalpy at the pump inlet (60 bar). The work done in an ideal isentropic process can be calculated using the equation:
W_ideal_pump = m_dot * (h_4s - h_3)
Where h_4s is the specific enthalpy at the pump inlet in an isentropic process. Rearranging the equations and substituting the given values, we can calculate the entropy generation in the pump:
s_dot_pump = m_dot * (h_4 - h_4s)
Similarly, we can calculate the entropy generation in the turbine using the equation:
s_dot_turbine = m_dot * (s_2 - s_1)
Where s_1 is the specific entropy at the turbine inlet and s_2 is the specific entropy at the turbine outlet. Given the specific entropies at the specified conditions, we can calculate the entropy generation in the turbine.
Learn more about Rankine steam power
brainly.com/question/16971298
#SPJ11
One penny is given a charge -q while another penny is given a charge +2q When the pennies are brought together and touched, the charges redistribute such that the pennies end up
with equal amounts of charge spread out over their respective surfaces.
(a) What is the final charge on each penny?
(b) Calculate the final charge on each penny if q is 30 uC (30 x 10°C).
(a) The final charge on each penny is 1/3 q.
When the two pennies having charge -q and +2q are brought together and touched, the charges get redistributed, and the pennies end up with equal amounts of charge spread out over their respective surfaces. The final charge on each penny is 1/3 q.
(b) The final charge on each penny is 15 µC.
q = 30 uC (30 × 10⁻⁶ C)
Initial charge on penny 1, q₁ = -q = -30 × 10⁻⁶ C
Initial charge on penny 2, q₂ = +2q = 2 × 30 × 10⁻⁶ C = 60 × 10⁻⁶ C = 6 × 10⁻⁵ C
Charge when the pennies touch = -q + 2q = q = 30 × 10⁻⁶ C
Charge gets distributed such that each penny has equal amount of charge spread over their respective surfaces, so the final charge on each penny is
q/2 = 30 × 10⁻⁶ / 2 = 15 × 10⁻⁶ C = 15 µC
Thus, the final charge on each penny is 15 µC.
Learn more about charge:
https://brainly.com/question/30236242
#SPJ11
The figure illustrates a number of optical lenses made of glass with index of refraction n. An equation from which the focal length of each lens in air can be calculated is: 1/f = (n-1)= 1/r1 + 1/r2) where ri and r2 are the magnitudes of the radii of curvature of the lens surfaces. r1 r2 0 r2 r1 z r2 r2 r1 ri Y Х ... Indicate the signs which are appropriate for the 1/r1 and 1/r2 terms in that equation: For lens y, the respective signs of 1/r2 and of 1/r1 are ✓ For lens X, the respective signs of 1/r1 and of 1/r2 are For lens Z, the respective signs of 1/r2 and of 1/r1 are .... Think of Fermat's Principle. 000
For lens Y, 1/r2 is positive and 1/r1 is negative. For lens X, 1/r1 is positive and 1/r2 is negative. For lens Z, 1/r2 is positive and 1/r1 is negative.
The given equation, 1/f = (n-1)(1/r1 + 1/r2), relates the focal length of a lens in air to the radii of curvature of its surfaces. For lens Y, the sign of 1/r2 is positive because the surface is convex towards the incident light, and the sign of 1/r1 is negative because the surface is concave away from the incident light. Similarly, for lens X, the sign of 1/r1 is positive due to the convex surface, and the sign of 1/r2 is negative due to the concave surface. For lens Z, 1/r2 is positive because of the convex surface, and 1/r1 is negative due to the concave surface. These signs ensure proper calculations based on Fermat's principle.
To know more about curvature, click here:
brainly.com/question/30106465
#SPJ11
The concept of resonance explains .. A. the cooking of food by microwaves B. the reception of radio waves by antennae
C. the collapse of the Tacoma Narrows Bridge
D. all of these
The correct answer is D: all of these. The concept of resonance explains various phenomena, including the cooking of food by microwaves, the reception of radio waves by antennae, and the collapse of the Tacoma Narrows Bridge.
Resonance occurs when an object or system vibrates at its natural frequency in response to an external force or stimulus. In the case of microwaves, the concept of resonance is utilized to cook food efficiently.
Microwaves generate electromagnetic waves that match the resonant frequency of water molecules, causing them to vibrate and generate heat. Similarly, radio waves are received by antennae through resonance.
The antennae are designed to resonate at specific frequencies, allowing them to capture the radio signals and convert them into electrical signals for transmission. In the case of the Tacoma Narrows Bridge, resonance played a detrimental role.
The bridge's structural design and the wind conditions caused the bridge to vibrate at its natural frequency, resulting in destructive oscillations and ultimately leading to its collapse. Therefore, resonance explains these phenomena, making option D, "all of these," the correct answer.
Learn more about concept of resonance here; brainly.com/question/13754408
#SPJ11
A magnifying glass gives an angular magnification of 4 for a person with a near-point distance of sN = 22 cm. What is the focal length of the lens?
The focal length of the magnifying glass lens is approximately -5.5 cm.
The angular magnification (m) of the magnifying glass is given as 4, and the near-point distance (sN) of the person is 22 cm. To find the focal length (f) of the lens, we can use the formula:
f = -sN / m
Substituting the given values:
f = -22 cm / 4
f = -5.5 cm
The negative sign indicates that the lens is a diverging lens, which is typical for magnifying glasses. Therefore, the focal length of the magnifying glass lens is approximately -5.5 cm. This means that the lens diverges the incoming light rays and creates a virtual image that appears larger and closer to the observer.
learn more about lens click here;
brainly.com/question/29834071
#SPJ11
A ball is thrown at 12 m/s from a 15-m tall tower. What is the speed of the ball just before it hits the ground if (a) air resistance is ignored and if (b) air resistance removes 1/4 of the total mechanical energy?
The ball will have a speed of 20.2 m/s just before it hits the ground and the ball will have a speed of 17.1 m/s just before it hits the ground.
a) If air resistance is ignored:
The ball will have a speed of 20.2 m/s just before it hits the ground.
The initial potential energy of the ball is mgh, where m is the mass of the ball, g is the acceleration due to gravity, and h is the height of the tower. The final kinetic energy of the ball is mv^2/2, where v is the speed of the ball just before it hits the ground.
When air resistance is ignored, the total mechanical energy of the ball is conserved. This means that the initial potential energy is equal to the final kinetic energy.
mgh = mv^2/2
v^2 = 2gh
v = sqrt(2gh)
v = sqrt(2 * 9.8 m/s^2 * 15 m) = 20.2 m/s
b) If air resistance removes 1/4 of the total mechanical energy:
The ball will have a speed of 17.1 m/s just before it hits the ground.
When air resistance removes 1/4 of the total mechanical energy, the final kinetic energy is 3/4 of the initial kinetic energy.
KE_f = 3/4 KE_i
mv^2_f/2 = 3/4 * mv^2_i/2
v^2_f = 3/4 v^2_i
v_f = sqrt(3/4 v^2_i)
v_f = sqrt(3/4 * 2 * 9.8 m/s^2 * 15 m) = 17.1 m/s
Learn more about speed with the given link,
https://brainly.com/question/13943409
#SPJ11
Fill in the following formula- frequency (MHz)= C in PZT
(mm/µs)/2 x
Frequency (MHz) = C / (2 * (mm/µs)), where C is the velocity of propagation in the PZT material.
In the given formula, the frequency (MHz) is determined by dividing the velocity of propagation in the PZT material (mm/µs) by twice the value of the wavelength (mm). The velocity of propagation, denoted by C, represents the speed at which mechanical waves travel through the PZT material. By dividing this velocity by twice the wavelength, we can calculate the frequency of the waves in megahertz. The wavelength is inversely proportional to the frequency, meaning that as the wavelength decreases, the frequency increases. This formula allows us to relate the velocity, wavelength, and frequency of mechanical waves in the PZT material.
To know more about Frequency, click here:
brainly.com/question/29739263
#SPJ11
5)Jorge has an electrical appliance that operates on 120v. He will soon travel to Peru, where wall outlets provide 230 V. Jorge decides to build a transformer so that his appliance will work for him in Peru. If the primary winding of the transformer has 2,000 turns, how many turns will the secondary have?
The number of turns the secondary will have, if the primary winding of the transformer has 2,000 turns, is 3,833 turns.
How to find the number of turns ?The number of turns in the transformer coils are proportional to the voltage that the coil handles. This can be represented by the equation:
V_primary / V_secondary = N_primary / N_secondary
Rearranging the equation to solve for the secondary turns would give:
N_secondary = N_primary * V_secondary / V_primary
N_secondary = 2000 * 230 / 120
N_secondary = 3, 833 turns
Therefore, Jorge's transformer will need approximately 3833 turns in the secondary coil.
Find out more on primary winding at https://brainly.com/question/16540655
#SPJ4
Calculate No(E), the density of occupied states for a metal with a Fermi energy of 6.50 eV and at a temperature of 847 K for an energy Eof (a) 4.50 eV, (b) 6.25 eV, (c) 6.50 eV, (d) 6.75 eV, and (e) 8.50 eV.
The density of occupied states (No(E)) is a measure of the number of energy states occupied by electrons in a metal at a given energy level E. It can be calculated using the Fermi-Dirac distribution function
For (a) 4.50 eV and (e) 8.50 eV, No(E) will be zero since these energies are lower and higher than the Fermi energy, respectively. For (b) 6.25 eV and (d) 6.75 eV, No(E) will be nonzero but less than the maximum value. At (c) 6.50 eV, No(E) will be at its maximum, indicating that the energy level coincides with the Fermi energy.
No(E) = 2 * (2πm/(h^2))^3/2 * ∫[E_F, E] (E-E_F)^(1/2) / [1 + exp((E - E_F)/(k*T))]
where E_F is the Fermi energy, m is the electron mass, h is the Planck's constant, k is the Boltzmann constant, and T is the temperature.
(a) For an energy level of 4.50 eV, which is lower than the Fermi energy (6.50 eV), the integral term becomes zero, resulting in No(E) = 0.
(b) For an energy level of 6.25 eV, which is slightly lower than the Fermi energy, No(E) will be nonzero but less than the maximum value since the exponential term in the denominator will still be significant.
(c) At the Fermi energy of 6.50 eV, No(E) will be at its maximum value since the exponential term becomes 1, leading to a maximum occupation of energy states.
(d) For an energy level of 6.75 eV, which is slightly higher than the Fermi energy, No(E) will be nonzero but less than the maximum value, similar to the case in (b).
(e) For an energy level of 8.50 eV, which is higher than the Fermi energy, the integral term becomes zero again, resulting in No(E) = 0.
In summary, at 847 K, No(E) will be zero for energy levels below and above the Fermi energy. For energy levels close to the Fermi energy, No(E) will be nonzero but less than the maximum value. Only at the Fermi energy itself will No(E) reach its maximum, indicating full occupation of energy states at that energy level.
Learn more about mass here:
brainly.com/question/11954533
#SPJ11