Twenty of the 36 women polled engage in internet shopping. This represents around 55.6% of all the women questioned.
To find the percentage of women who shop online, we need to calculate the ratio of women who shop online to the total number of women surveyed and then multiply it by 100 to get the percentage.
According to the data provided:
- Total women surveyed: 36
- Women who shop online: 20
To find the percentage, we'll use the following formula:
(Online shoppers / Total surveyed) × 100
Percentage of women who shop online = (20 / 36) × 100 ≈ 55.6%
Therefore, approximately 55.6% of the women surveyed shop online.
In summary, out of the 36 women surveyed, 20 of them shop online. This accounts for approximately 55.6% of the total women surveyed.
For more questions on percentage, click on:
https://brainly.com/question/24877689
#SPJ8
Complete the following equivalencies: 1. 1 kg = 2. 1 in = 3. 1 fl oz = 4. 1 cup = 5. 30 g = 6. 6.5 in = 7. 0.75 mL = 8. 5 fl oz = 9. 60 mL = 10. 80 kg = lb cm mg lb ml cm
All the complete measures of units are,
1. 1 kg = 2.20 lb (pounds)
2. 1 inch = 2.54 cm
3. 1 fl oz = 29.5735 ml
4. 1 cup = 236.588 ml
5. 30 g = 30000 mg
6. 6.5 inches = 16.51 cm
7. 0.75 ml = 0.00075 L
8. 8. 5 fl oz = 148 ml
9. 60 ml = 4.056 tbsp
10. 80 kg = 176 lb
We have to find all the equivalent measures of units.
All the complete units are,
1. 1 kg = 2.20 lb (pounds)
2. 1 inch = 2.54 cm
3. 1 fl oz = 29.5735 ml
4. 1 cup = 236.588 ml
5. 30 g
= 30 x 1000
= 30000 mg
6. 6.5 inches
= 6.5 x 2.54 cm
= 16.51 cm
7. 0.75 ml
= 0.75/1000 L
= 0.00075 L
8. 5 fl oz
= 5 x 29.6 ml
= 148 ml
9. Since, 1 ml = 0.0676 tbsp
60 ml = 60 x 0.0676 tbsp
= 4.056 tbsp
10. 80 kg
= 80 x 2.2 lb
= 176 lb
To learn more about the measurement unit visit:
https://brainly.com/question/777464
#SPJ4
1) Draw the arrow-pushing mechanism of the following reaction: (10 pts)
The arrow-pushing mechanism of the given reaction is as follows During the given reaction, a Grignard reagent i.e. CH3MgBr is used as a nucleophile to attack the carbonyl carbon of benzaldehyde. A nucleophile is a chemical species that donates an electron pair to an electrophile in order to form a chemical bond in a reaction.
In the first step, the Grignard reagent attacks the electrophilic carbonyl carbon of benzaldehyde to form a tetrahedral intermediate. This is the slow and rate-determining step of the reaction, as it involves the breaking of the π bond in the carbonyl group, followed by the formation of a new bond between the carbonyl carbon and the magnesium atom of the Grignard reagent.In the second step, the tetrahedral intermediate is deprotonated by a proton source, such as water, to form the alcohol product.
The alcohol product is protonated at the end of the reaction to form the final product, 1-phenyl-1-propanol, which is shown below:More than 100 words are given to explain the mechanism of the given reaction using arrow pushing. The Grignard reaction is an important tool for the formation of carbon-carbon bonds in organic chemistry. It involves the reaction of an organomagnesium halide with an electrophilic compound, such as a carbonyl group, to form a new carbon-carbon bond. The reaction proceeds through a tetrahedral intermediate, which is formed by the addition of the nucleophile to the carbonyl group. The intermediate is then deprotonated to form the final product.
To know more about mechanism visit :
https://brainly.com/question/33643507
#SPJ11
Pr. 4: For the reservoir and sheet pile cut-off above, Determine: a) The rate of flow (q) per unit width, b) The distribution of porewater pressure in both sides of the sheet pile.
The pore water pressure on the water side of the sheet pile is 19.62 k
Pa and the pore water pressure on the soil side of the sheet pile is 78.48 kPa.
a) The rate of flow (q) per unit width: For calculating the rate of flow per unit width, we can use the Darcy’s law. Darcy’s law for saturated soil is given as: Q = -k*A[(dh/dx)n/l]
where Q is the flow rate per unit area or discharge per unit width of soil (m3/m/s), k is the hydraulic conductivity (m/s),
A is the cross-sectional area of soil normal to the direction of flow (m2/m), dh/dx is the hydraulic gradient (dimensionless), n is the porosity (dimensionless), and l is the length of soil in the direction of flow (m) .
Now, the cross-sectional area of the soil is given by the following formula:
[tex]A = H + d/2 …………. (i)H = 12 + 2 + 6 + 3 = 23 md = 12/100 = 0.12m[/tex]
Using equation (i), we have: A = 23 + 0.12/2 = 23.06 m2/m
As given, hydraulic gradient is:dh/dx = (5 – 2.5)/20 = 0.125 m/m
Substituting all the given values in the above equation, we get:
[tex]q = -0.0002*23.06*0.125 = 0.00057 m3/s/m = 570 L/h/m[/tex]
Therefore, the flow rate per unit width is 570 L/h/m.b) T
he distribution of porewater pressure in both sides of the sheet pile: The water pressure on the water side of the sheet pile is calculated using the following formula:[tex]u = γw *[/tex]H
Where u is the water pressure on the water side (kPa), γw is the unit weight of water (9.81 kN/m3), and H is the height of water above the bottom of the sheet pile [tex](m).u = 9.81*2 = 19.62 kPa[/tex]
To know more about pressure visit:
https://brainly.com/question/33464916
#SPJ11
Suppose that a 10-in x 11-in rectangular prestressed concrete pile is to be driven 160 ft into a uniform deposit of clay, having an unconfined compressive strength qu of 458 psf and a unit weight of 117 pcf. What is the total capacity of the pile? Assume that the clay properties are exactly average for typical clay soils. Report your answer in kips to the nearest whole number. Do not include the units in your answer.
The total capacity of the pile is approximately 65 kips, considering both skin friction and end bearing capacity.
To determine the total capacity of the pile, we need to consider the skin friction and the end bearing capacity.
Skin Friction:
Skin friction is the resistance developed between the pile surface and the surrounding soil. We can calculate the skin friction using the average clay properties and the pile surface area.The area of the pile surface is:
Area = Length × Perimeter = (160 ft) × (10 in + 11 in) = 3360 in²The skin friction capacity can be calculated using the following formula:
Skin friction capacity = Area × Skin friction resistance per unit areaFor typical clay soils, the skin friction resistance per unit area can be estimated using empirical formulas, such as the Terzaghi and Peck method. The formula states that the skin friction resistance per unit area (qf) is proportional to the undrained shear strength (su) of the clay.Assuming the undrained shear strength (su) is approximately equal to the unconfined compressive strength (qu), we have:
qf = c × suFor typical clay soils, the coefficient 'c' can be taken as 0.5.qf = 0.5 × qu = 0.5 × 458 psf = 229 psfTherefore, the skin friction capacity is:
Skin friction capacity = Area × qf = 3360 in² × 229 psf = 769,440 in-lbs
To convert the capacity to kips, we divide by 12,000 (1 kip = 12,000 in-lbs):
Skin friction capacity = 769,440 in-lbs / 12,000 = 64 kips (approximately)
End Bearing Capacity:
The end bearing capacity is the resistance developed at the base of the pile. It depends on the unit weight of the soil and the pile area at the base.The base area of the pile is:
Area = Length × Width = (10 in) × (11 in) = 110 in²The end bearing capacity can be calculated using the following formula:End bearing capacity = Area × Unit weight of soilEnd bearing capacity = 110 in² × 117 pcf = 12,870 in-lbsConverting the end bearing capacity to kips:
End bearing capacity = 12,870 in-lbs / 12,000 = 1 kip (approximately)
Total Capacity:
The total capacity of the pile is the sum of the skin friction capacity and the end bearing capacity:
Total capacity = Skin friction capacity + End bearing capacityTotal capacity = 64 kips + 1 kip = 65 kips (approximately)Therefore, the total capacity of the pile is approximately 65 kips.
learn more about Pile Capacity.
brainly.com/question/33584165
#SPJ11
Calculate the pH of 100.00mL of 0.20 M HNO_3 solution after 67.00 mL of NaOH 0.20 M have been added.
the pH of the resulting solution is approximately 1.404.
To calculate the pH of the solution after the addition of NaOH, we need to determine the moles of acid and base, and then calculate the concentration of the resulting solution. Here are the steps to solve the problem:
1. Determine the moles of HNO₃:
Moles of HNO₃ = volume (in L) * concentration
Moles of HNO₃ = 0.100 L * 0.20 M
2. Determine the moles of NaOH:
Moles of NaOH = volume (in L) * concentration
Moles of NaOH = 0.067 L * 0.20 M
3. Determine the moles of HNO₃ that reacted with NaOH:
Since NaOH is a 1:1 stoichiometric ratio with HNO₃, the moles of HNO₃ that reacted with NaOH are equal to the moles of NaOH.
4. Determine the remaining moles of HNO₃:
Remaining moles of HNO₃ = Initial moles of HNO₃ - Moles of HNO₃ reacted
5. Determine the volume of the resulting solution:
The volume of the resulting solution is the sum of the initial volumes of HNO₃ and NaOH.
6. Calculate the concentration of the resulting solution:
Concentration of resulting solution = Remaining moles of HNO₃ / Volume of resulting solution
7. Calculate the pH of the resulting solution:
pH = -log[H₃O⁺]
Now, let's perform the calculations:
1. Moles of HNO₃ = 0.100 L * 0.20 M = 0.020 moles
2. Moles of NaOH = 0.067 L * 0.20 M = 0.0134 moles
3. Moles of HNO₃ reacted = 0.0134 moles
4. Remaining moles of HNO₃ = 0.020 moles - 0.0134 moles = 0.0066 moles
5. Volume of resulting solution = 0.100 L + 0.067 L = 0.167 L
6. Concentration of resulting solution = 0.0066 moles / 0.167 L ≈ 0.0395 M
7. pH = -log[0.0395] ≈ 1.404
To know more about addition visit:
brainly.com/question/29464370
#SPJ11
Consider the NMR spectrum of m-dichlorobenzene. For each of your answers, enter a number in the box, not a word. a.How many signals would we expect to see in the ^1H NMR spectrum? b.How many signals would we expect to see in the ^13C NMR spectrum?
a. The ^1H NMR spectrum of m-dichlorobenzene would have 2 signals.
b. The ^13C NMR spectrum of m-dichlorobenzene would have 1 signal.
a. The number of signals in the ^1H NMR spectrum of m-dichlorobenzene can be determined by counting the distinct peaks on the spectrum. Each peak corresponds to a different hydrogen atom in the molecule. In m-dichlorobenzene, there are two sets of equivalent hydrogen atoms, one attached to each of the two chlorine atoms. These two sets of equivalent hydrogen atoms will give rise to two distinct signals in the ^1H NMR spectrum. Therefore, we would expect to see 2 signals in the ^1H NMR spectrum of m-dichlorobenzene.
b. The number of signals in the ^13C NMR spectrum of m-dichlorobenzene can be determined in a similar way as in the ^1H NMR spectrum. Each distinct peak on the spectrum corresponds to a different carbon atom in the molecule. In m-dichlorobenzene, there are six carbon atoms. However, all six carbon atoms are equivalent due to the symmetry of the molecule. Therefore, we would expect to see only one signal in the ^13C NMR spectrum of m-dichlorobenzene.
In summary:
a. The ^1H NMR spectrum of m-dichlorobenzene would have 2 signals.
b. The ^13C NMR spectrum of m-dichlorobenzene would have 1 signal.
Learn more about NMR spectrum:
https://brainly.com/question/30583972
#SPJ11
If the K_a is 1.8×10^−5 for acetic acid, what is the pH of a solution which is 0.250M acetic acid and 0.250M sodium acetate?
The pH of a solution containing 0.250 M acetic acid and 0.250 M sodium acetate, with a K_a value of 1.8×10^−5 for acetic acid, is approximately ______.
To determine the pH of the solution, we need to consider the acid dissociation of acetic acid (CH3COOH) and the presence of its conjugate base, acetate (CH3COO-), from sodium acetate (CH3COONa).
The Henderson-Hasselbalch equation is used to calculate the pH of a solution containing a weak acid and its conjugate base:
pH = pKa + log ([A-]/[HA])
In this case, acetic acid acts as the weak acid (HA) and acetate is its conjugate base (A-). The pKa value of acetic acid is -log(Ka) = -log(1.8×10^−5).
Given the concentrations of acetic acid and acetate in the solution (0.250 M for both), we can substitute these values into the Henderson-Hasselbalch equation to find the pH.
pH = -log(1.8×10^−5) + log (0.250/0.250)
By evaluating this expression, we can determine the pH of the solution.
Learn more about sodium acetate visit:
https://brainly.com/question/30778914
#SPJ11
56. Write the two resonance structures for the pyridinium ion, CSHSNH4 60. Write fwo complete, balanced equations for each of the followine reaction, one usine condensed formulas and one usine Lewis structures. Lthdammentum, chloride is added to a solution of sodlum hydroside. I?
The reaction of Sodium hydroxide with Hydrochloric acid (Na+ and Cl- are not covalently bonded)
The Pyridinium ion has two resonance structures.
The two resonance structures of the Pyridinium ion, CSHSNH4 are as follows:Pyridinium ion Lewis structures
The two complete, balanced equations for each of the following reaction, one using condensed formulas and one using Lewis structures are as follows:
Reaction of Lithium with water (Condensed formula)2Li(s) + 2H₂O(l) → 2LiOH(aq) + H₂(g)Reaction of Lithium with water (Lewis structure)
The reaction of lithium with water is shown as follows:
The reaction of Lithium with water (Li+ and OH- are not covalently bonded) Reaction of Sodium hydroxide with Hydrochloric acid (Condensed formula)NaOH(aq) + HCl(aq) → NaCl(aq) + H₂O(l)Reaction of Sodium hydroxide with Hydrochloric acid (Lewis structure)
The reaction of Sodium hydroxide with Hydrochloric acid is shown as follows:
The reaction of Sodium hydroxide with Hydrochloric acid (Na+ and Cl- are not covalently bonded).
To know more about Sodium hydroxide visit:
brainly.com/question/29995610
#SPJ11
3. The gusset plate is subjected to the forces of three members. Determine the tension force in member C for equilibrium. The forces are concurrent at point O. Take D as 10 kN, and F as 8 kN 7 MARKS D
The tension force in member C for equilibrium is 6 kN.
To determine the tension force in member C, we need to analyze the forces acting on the gusset plate. Since the forces are concurrent at point O, we can consider the equilibrium of forces.
First, let's label the forces: A, B, and C. Given that D is 10 kN and F is 8 kN, we can assume that the force C acts in the opposite direction of D and F, as it is the only remaining force.
To find the tension force in member C, we can set up the equilibrium equations. The sum of the vertical forces must be zero, and the sum of the horizontal forces must also be zero. Since the forces are concurrent at point O, the sum of the moments about O must be zero as well.
Let's assume that the vertical forces acting on the gusset plate are positive when they are directed upward. With this assumption, the equilibrium equations can be written as follows:
ΣFy = C - D - F = 0 (Equation 1)
ΣFx = 0 (Equation 2)
ΣMO = F * x - D * y + C * d = 0 (Equation 3)
Here, x and y represent the horizontal and vertical distances of forces F and D from point O, respectively. d is the horizontal distance of force C from point O.
From Equation 1, we can solve for C:
C = D + F
C = 10 kN + 8 kN
C = 18 kN
Therefore, the tension force in member C for equilibrium is 18 kN.
Learn more about Tension
brainly.com/question/32546305
#SPJ11
CORROSION
- What happens to stainless steel in sodium chloride solution and why?
Stainless steel is known for its resistance to corrosion. However, it can corrode when exposed to environments that are aggressive. One of these environments is sodium chloride solution. Stainless steel can corrode in sodium chloride solution due to a process known as crevice corrosion.
Stainless steel corrodes in sodium chloride solution due to crevice corrosion. This process occurs when the stainless steel is exposed to a solution that has a chloride ion concentration of above 50 ppm. This concentration is typical in seawater and is the reason why stainless steel corrosion is common in marine environments. In crevice corrosion, the stainless steel forms a thin oxide layer that protects it from corrosion. However, in environments that have a high concentration of chloride ions, this layer can be penetrated. Chloride ions can accumulate in crevices, creating an acidic environment that eats away at the oxide layer. The stainless steel underneath is then exposed, leading to corrosion. Crevice corrosion can occur in areas where the stainless steel is in contact with other metals or where it is welded. These areas have small crevices that can trap chloride ions, leading to crevice corrosion.
In conclusion, stainless steel can corrode in sodium chloride solution due to crevice corrosion. Crevice corrosion occurs when the stainless steel is exposed to a solution with a chloride ion concentration of above 50 ppm. Chloride ions can accumulate in small crevices, creating an acidic environment that eats away at the oxide layer. The stainless steel underneath is then exposed, leading to corrosion.
learn more about corrosion visit:
brainly.com/question/14995025
#SPJ11
(1) Give a reasonable Lewis structure, including formal charges, for HNC (N.B. N is the central atom). H, N, and C are in groups 1, 5, and 4 and their atomic numbers are 1, 7, and 6.
The Lewis structure for HNC all atoms have a formal charge of 0.
To determine the Lewis structure for HNC, to follow a few guidelines:
Count the total number of valence electrons: Hydrogen (H) has 1 valence electron, Nitrogen (N) has 5 valence electrons, and Carbon (C) has 4 valence electrons. Therefore, the total number of valence electrons is 1 + 5 + 4 = 10.
Identify the central atom: Nitrogen (N) is the central atom since it is less electronegative than Carbon (C).
Form single bonds: Connect each atom to the central atom with a single bond, using two valence electrons for each bond. This will account for 2 x 3 = 6 electrons.
H - N - C
Distribute the remaining electrons: 10 - 6 = 4 electrons remaining. Place them as lone pairs around the atoms to satisfy the octet rule.
H - N - C
|
H
Check for octet rule and formal charges: Each atom should have an octet of electrons (except Hydrogen, which only needs 2 electrons). In this case, Nitrogen has 2 lone pairs and a total of 8 electrons, satisfying the octet rule. Carbon also has 8 electrons, while Hydrogen has 2 electrons.
H - N - C
|
H
Determine formal charges: To calculate formal charges, compare the number of valence electrons of each atom with the number of electrons it possesses in the Lewis structure. The formal charge is calculated using the formula: Formal charge = Number of valence electrons - Number of lone pair electrons - Number of bonded electrons.
For Nitrogen (N): Formal charge = 5 - 2 - 4 = -1
For Carbon (C): Formal charge = 4 - 0 - 4 = 0
For Hydrogen (H): Formal charge = 1 - 0 - 2 = -1
To know more about atoms here
https://brainly.com/question/13654549
#SPJ4
The graph of the function f(x) = –(x + 3)(x – 1) is shown below.
On a coordinate plane, a parabola opens down. It goes through (negative 3, 0), has a vertex at (negative 1, 4), and goes through (1, 0).
Which statement about the function is true?
The function is positive for all real values of x where
x < –1.
The function is negative for all real values of x where
x < –3 and where x > 1.
The function is positive for all real values of x where
x > 0.
The function is negative for all real values of x where
x < –3 or x > –1.
Answer: Choice B
Reason:
The graph is an upside down parabola. The parabola opens downward. The x-intercepts are at -3 and 1. Between these roots the parabola is above the x axis, so the function is positive. We write y > 0 when -3 < x < 1.
On the other hand, y < 0 when either x < -3 or x > 1. This points us to choice B
Use calculus to evaluate the following limits. Write DNE if the limit does not exist. Show all your work. 3x³+x²+1 x³+1 a. lim x →[infinity]0 x²-x x-3 x²-2x-3 b. lim C. lim x²-1 x-1 X-1 d. lim e. lim. f. 4 x-00-x²+8x-1 x+0x³+x²–2x x²+2 lim x+-1x²+1
To evaluate the limit lim x→-1 (x² + 1)/(x² + 1), we can directly substitute x = -1 into the expression
a. To evaluate the limit lim x→∞ (3x³ + x² + 1)/(x³ + 1), we compare the degrees of the highest power of x in the numerator and denominator. Since both are cubics, we divide each term by the highest power of x in the denominator:
lim x→∞ (3x³/x³ + x²/x³ + 1/x³)/(x³/x³ + 1/x³)
= lim x→∞ (3 + 1/x + 1/x³)/(1 + 1/x³)
As x approaches infinity, the terms 1/x and 1/x³ both approach 0. Therefore, the limit simplifies to:
= (3 + 0 + 0)/(1 + 0) = 3/1 = 3
b. To evaluate the limit lim x→3 (x² - x)/(x² - 2x - 3), we can directly substitute x = 3 into the expression:
lim x→3 (3² - 3)/(3² - 2(3) - 3)
= lim x→3 (9 - 3)/(9 - 6 - 3)
= 6/0
The denominator evaluates to 0, indicating an undefined value. Therefore, the limit does not exist (DNE).
c. To evaluate the limit lim x→1 (x² - 1)/(x - 1), we can factor the numerator as (x - 1)(x + 1):
lim x→1 [(x - 1)(x + 1)]/(x - 1)
= lim x→1 (x + 1)
Substituting x = 1 into the expression, we get:
lim x→1 (1 + 1) = 2
d. To evaluate the limit lim x→0 (x³ + x² - 2x)/(x² + 2), we can directly substitute x = 0 into the expression:
lim x→0 (0³ + 0² - 2(0))/(0² + 2)
= lim x→0 0/-2 = 0
e. To evaluate the limit lim x→∞ x²/(x - 1), we can divide each term by the highest power of x in the denominator:
lim x→∞ (x²/x)/(x/x - 1/x)
= lim x→∞ (1)/(1 - 1/x)
= 1/1 = 1
f. To evaluate the limit lim x→-1 (x² + 1)/(x² + 1), we can directly substitute x = -1 into the expression:
lim x→-1 (-1² + 1)/(-1² + 1)
= lim x→-1 (1)/ (1)
= 1/1 = 1
learn more about limit
https://brainly.com/question/12211820
#SPJ11
Describe the differences between electrolytes and nonelectrolytes using terms of conductivity and dissociation.
The key differences between electrolytes and nonelectrolytes lie in their ability to dissociate into ions and conduct electricity, with electrolytes having the capacity to dissociate and conduct current, while nonelectrolytes do not dissociate and are non-conductive.
Electrolytes and nonelectrolytes are substances that differ in terms of conductivity and dissociation.
Electrolytes are substances that conduct electricity when dissolved in water or molten state, while nonelectrolytes do not conduct electricity in either state. This difference arises from their varying abilities to dissociate into ions.
Electrolytes, such as salts and acids, dissociate into ions when dissolved in water or melted. The resulting ions can move freely in the solution, enabling the flow of electric current.
Strong electrolytes dissociate almost completely, yielding a high concentration of ions and exhibiting high conductivity.
Weak electrolytes, on the other hand, only partially dissociate, leading to a lower concentration of ions and relatively lower conductivity.
In contrast, nonelectrolytes, including many organic compounds and covalent molecules, do not dissociate into ions when dissolved. They remain as intact molecules and therefore do not facilitate the flow of electric current. Consequently, nonelectrolyte solutions exhibit negligible conductivity.
Learn more about the electrolytes and nonelectrolytes here:
https://brainly.com/question/5547666
#SPJ4
1. A circular rug has a diameter of 10 cm. What is its area?
A. 7.850 cm2
B. 78.50 cm2
C. 785.0 cm2
D. 7850 cm2
2. The diameter of a circle is 8 cm. What is its area?
A. 50.24 cm2
B. 50.24 cm2
C. 502.4 cm2
D. 5024 cm2
3. Which formula shows the correct way of finding the area of a circle?
A. A πr²
B. A = πr
C. A = π²r
D. A = 2nr
Answer:
1. B. 78.50 cm2
2. In this question 2 options are same, A and B, one of the options may be 50.72 cm2. And this the correct answer.
3. C. A = π²r
Sort the following functions in terms of asymptotic growth from
largest to smallest.
52!
3log(n^9)
n^(1/3)
n^(3.14)
n^n
n
n^2log(n^2)
For example
1. n^n
2.
3.
4.
5.
6.
7. 52!
In terms of asymptotic growth from largest to smallest, the sorted order of the given functions would be as follows:
1.[tex]n^n[/tex]
2.52!
3.[tex]n^2log(n^2)[/tex]
4.[tex]n^{(3.14)[/tex]
5.[tex]n^{(1/3)[/tex]
6.[tex]3log(n^9)[/tex]
7.n
1.The function [tex]n^n[/tex]grows the fastest as the exponent is proportional to the input size n.
2.52! (factorial) grows rapidly but not as fast as [tex]n^n[/tex].
3.[tex]n^2log(n^2)[/tex] has a higher growth rate than the remaining functions due to the logarithmic term.
4.[tex]n^{(3.14)[/tex]has a higher growth rate than [tex]n^{(1/3)[/tex] but lower than [tex]n^2log(n^2)[/tex].
5.[tex]n^{(1/3)[/tex] grows slower than [tex]n^{(3.14)[/tex] but faster than [tex]3log(n^9)[/tex].
6.[tex]3log(n^9)[/tex] grows slower than [tex]n^{(1/3)[/tex] but faster than n.
7.n has the slowest growth rate among the given functions.
Note: The growth rates are based on the Big O notation, which provides an upper bound on the function's growth rate.
To learn more about asymptotic visit:
brainly.com/question/32503997
#SPJ11
Use Hess's law and the measured mean enthalpy changes for the NaOH−HCl and NH3−HCl reactions to calculate the enthalpy change to be expected for the reaction NaOH+NH 4 Cl→NaCl+NH 3+H2 O
The expected enthalpy change for the reaction NaOH+NH4Cl→NaCl+NH3+H2O
is -109.2 kJ/mol.
The Hess's law states that the enthalpy change of a reaction is independent of the route taken. This law makes use of the fact that enthalpy is a state function, meaning that the enthalpy change of a reaction is dependent only on the initial and final states and is not affected by the intermediate steps taken in reaching those states.
Thus, the sum of the enthalpy changes for a series of reactions that results in the overall reaction will be equal to the enthalpy change of the overall reaction. Given the reaction:
NaOH+NH4Cl→NaCl+NH3+H2O
It is not possible to measure the enthalpy change of this reaction directly.
However, we can use Hess's law to calculate the expected enthalpy change using the enthalpy changes of the following reactions:
NaOH + HCl → NaCl + H2ONH3 + HCl → NH4Cl
Adding these two reactions gives:
NaOH + NH4Cl → NaCl + NH3 + H2O
The enthalpy change for this overall reaction can be calculated using Hess's law as the sum of the enthalpy changes for the two reactions that lead to the overall reaction, which are NaOH−HCl and NH3−HCl reactions. The enthalpy change of NaOH−HCl is -57.5 kJ/mol, and the enthalpy change of NH3−HCl is -51.7 kJ/mol.
The expected enthalpy change for the reaction NaOH+NH4Cl→NaCl+NH3+H2O
is the sum of the enthalpy changes of the two reactions that lead to it. Therefore,
∆H = ∆H(NaOH−HCl) + ∆H(NH3−HCl)∆H
= (-57.5 kJ/mol) + (-51.7 kJ/mol)∆H
= -109.2 kJ/mol
Therefore, the expected enthalpy change for the reaction NaOH+NH4Cl→NaCl+NH3+H2O
is -109.2 kJ/mol.
For more information on Hess's law visit:
brainly.com/question/31508978
#SPJ11
A 700 mm diameter circular long column (Lu=6500mm) carries an axial load of PDL=3000kN and PLL=2400kN The column is part of a braced frame that is bend in a single curvature. The ratio of eccentricities at top and bottom of the column is 1.1 and the effective length factor k=0.85. Use f’c=35MPa, fy=420MPa, and assume the larger of the two end moments is greater than the minimum moment. Calculate the value of kLu/r.
The value of kLu/r≈ 542.1.The formula for computing the value of kLu/r is given byk = effective length factor Lu = unsupported leng t
Given, Diameter of circular column = 700 mm
Length of column = Lu = 6500 mm
Axial load at top of column = PDL = 3000 k N
Axial load at bottom of column = PLL = 2400 kN
Eccentricity ratio at top and bottom of column = 1.1
Effective length factor = k = 0.85 Concrete compressive strength = f’c = 35 M PaSteel yield strength = fy = 420 MPa
We can use the below formula to find the radius of gyration:
kr = 0.049√f'c/fy
kr = 0.049√35/420
= 0.003769
Approximated
kr value = 0.0038
r = d/2 = 700/2
= 350 mmkLu/r
= k(Lu/r) =
(0.85 × 6500 mm)/(350 mm × 0.0038)
≈ 542.1
To know more about Diameter visit:
https://brainly.com/question/32968193
#SPJ11
Protein called p53 is known to have a very important function is cell life and death.
There is a gene called p53 that codes for this protein. When the time comes for an old cell to die, this gene gets turned on. It gets transcribed into p53 mRNA, then this mRNA gets translated by ribosomes into the p53 protein, which then gets activated. Once activated, p53 Protein initiates the self-destruction of the old cell. The process of programmed self-destruction of cells is called Apoptosis. Recently, scientists discovered that in cancer cells, the gene coding for p53 protein is mutant (wrong DNA sequence). Step by step describe the consequences of p53 gene mutation: Describe starting from transcription, to translation, to activation, ending with function, how this protein's shape (and function) could come out different/abnormal, after a change in p53 DNA sequence. How can it lead to development of masses of cells (tumors)?
Overall, the mutation in the p53 gene can result in the production of a structurally and functionally altered p53 protein. This abnormal protein is unable to carry out its normal tumor suppressor functions, leading to the loss of cell regulation and the potential development of tumors.
Transcription: The mutated p53 gene can lead to errors during transcription, resulting in the production of a mutant p53 mRNA. The mRNA may contain incorrect information due to the changes in the DNA sequence.
Translation: The mutant p53 mRNA is then translated by ribosomes into a mutant p53 protein. During translation, the ribosomes read the mRNA sequence and assemble amino acids to form the protein. However, the mutation in the DNA sequence can lead to the incorporation of incorrect amino acids or the production of an incomplete protein.
Protein Structure and Function: The mutated p53 protein may have an altered structure compared to the normal p53 protein. The change in amino acid sequence can disrupt the folding and three-dimensional structure of the protein. As a result, the mutant p53 protein may not be able to perform its normal functions effectively or may acquire new abnormal functions.
To know more about mutation,
https://brainly.com/question/33239194
#SPJ11
assume you purchased some corporate stock 4 years ago for $7,500. You received quarterly dividends of 875 ; your dividends total $1,200 (16 dividend checks ×$75=$1,200). You sold the stock today for $8,050. 6. The PV is $8,050 because that is the amount you received today (in the present). (T or F ) 7. $1,200 represents which variable (PV, PMT, or FV)? 8. What is the FV amount? Unit 12.2 Financial calculators 9. When is it not necessary to clear the TVM registers? 10. By setting our "periods per year" register at 1 we must enter the periodic rate in the i-register. (T or F)
6. False. The present value (PV) is the initial investment or the amount invested in the stock, which is $7,500, not the amount received today ($8,050).
7. $1,200 represents the variable PMT (Payment). It represents the total dividends received over the four-year period.
8. The future value (FV) amount is $8,050, which is the amount received from selling the stock today.
9. It is not necessary to clear the TVM (Time Value of Money) registers when the calculations are completed, and you don't need to perform any further calculations.
10. True. When the "periods per year" register is set to 1, the periodic rate (interest rate) should be entered directly into the i-register as a decimal value, such as 0.05 for 5%.
Therefore, the PV is not $8,050 but $7,500, representing the initial investment. The variable $1,200 represents the PMT (payment) or the total dividends received. The FV amount is $8,050, the selling price of the stock. Clearing the TVM registers is not necessary after completing calculations, and when "periods per year" is set to 1, the periodic rate is entered directly into the i-register.
Learn more about initial investment visit:
https://brainly.com/question/29726908
#SPJ11
Smallest to biggest. 0.43,3/7,43.8%,7/16
Answer: 3/7 (Smallest), 0.43, 7/16, 43.8% (largest)
Step-by-step explanation:
0.43
3/7 = 0.4286
43.8% = 0.438
7/16 = 0.4375
Question 1 a. Hydraulic jump is the rise of water level, which takes place due to transformation of the unstable shooting flow (supercritical) to the stable streaming (sub-critical). i. Classify the hydraulic jump with sketch of diagram and explain them with Froude's number.
In case of hydraulic jump, the Froude number is used to classify whether it is a classical jump or an undular jump. If the Froude number is less than one, the hydraulic jump is classified as an undular jump. If the Froude number is greater than one, the hydraulic jump is classified as a classical jump.
Hydraulic jump
Hydraulic jump is the sudden rise of water level that occurs when the flow of liquid is transformed from unstable shooting flow (supercritical) to stable streaming (sub-critical). This occurs when the velocity of the supercritical flow becomes less than that of the critical flow.
The hydraulic jump is often employed in engineering practices such as spillways, energy dissipators, and stepped cascades to alleviate the erosive effect of flowing water. Hydraulic jump can be classified into two main types, namely; the undular jump and the classical jump.
ii. Hydraulic jump classification
The hydraulic jump can be classified into two types, namely, undular jump and classical jump.
The Undular jump
This type of hydraulic jump is characterized by the formation of waves on the free surface of the liquid. It's also known as a weak jump. It occurs when the velocity of the supercritical flow is only slightly greater than the critical velocity. This implies that the kinetic energy of the fluid is not totally converted into potential energy and turbulence and waves are formed on the surface of the liquid.
Classical jump
The classical jump, also known as the strong jump, occurs when the velocity of the supercritical flow is considerably greater than the critical velocity. The energy of the fluid is almost completely transformed into potential energy in this scenario. The classical jump is distinguished by a sharp rise in water level, high turbulence and eddies on the liquid surface, and a distinct flow pattern of the liquid.
iii. Froude number explanation
Froude number is a dimensionless number used in fluid mechanics. It is the ratio of the inertial force of a fluid to the gravitational force acting on it.
Mathematically, it can be expressed as: F= V / (gL)^0.5,
where V is the velocity of the fluid, g is the acceleration due to gravity, and L is the characteristic length of the flow. The Froude number is used to determine the flow regime of a fluid flow. For hydraulic jump, the Froude number can be used to classify the hydraulic jump as either undular or classical.
The Froude number is given by: F = V / √(gL)
Where: F = Froude number
V = Velocity of the fluid
g = Acceleration due to gravity
L = Length characteristic to the flow
In case of hydraulic jump, the Froude number is used to classify whether it is a classical jump or an undular jump. If the Froude number is less than one, the hydraulic jump is classified as an undular jump. If the Froude number is greater than one, the hydraulic jump is classified as a classical jump.
To know more about Froude numbe, visit:
https://brainly.com/question/33588981
#SPJ11
One cubic meter of argon is taken from 1 bar and 25°C to 10 bar and 300°C by each of the following two-step paths. For each path, compute Q, W, AU, and AH for each step and for the overall process. Assume mechanical reversibility and treat argon as an ideal gas with Cp= (5/2)R and Cy= (3/2)R. (a) Isothermal compression followed by isobaric heating. (6) Adiabatic compression followed by isobaric heating or cooling. (c) Adiabatic compression followed by isochoric heating or cooling. (d) Adiabatic compression followed by isothermal compression or expansion.
For the path of isothermal compression followed by isobaric heating, the overall process involves two steps. The main answer:
- Step 1: Isothermal compression - Q = 0, W < 0, ΔU < 0, ΔH < 0
- Step 2: Isobaric heating - Q > 0, W = 0, ΔU > 0, ΔH > 0
- Overall process: Q > 0, W < 0, ΔU < 0, ΔH < 0
In the first step, isothermal compression, the temperature remains constant at 25°C while the pressure increases from 1 bar to 10 bar. Since there is no heat transfer (Q = 0) and work is done on the system (W < 0), the internal energy (ΔU) and enthalpy (ΔH) decrease. This is because the gas is being compressed, resulting in a decrease in volume and an increase in pressure.
In the second step, isobaric heating, the pressure remains constant at 10 bar while the temperature increases from 25°C to 300°C. Heat is transferred to the system (Q > 0) but no work is done (W = 0) since the volume remains constant. As a result, both the internal energy (ΔU) and enthalpy (ΔH) increase. This is because the gas is being heated, causing the molecules to gain kinetic energy and the overall energy of the system to increase.
For the overall process, the values of Q, W, ΔU, and ΔH can be determined by adding the values from each step. In this case, since the isothermal compression step has a negative contribution to ΔU and ΔH, and the isobaric heating step has a positive contribution, the overall process results in a decrease in internal energy (ΔU < 0) and enthalpy (ΔH < 0). Additionally, since work is done on the system during the compression step (W < 0), the overall work is negative (W < 0).
Know more about Isothermal compression here:
https://brainly.com/question/32558407
#SPJ11
True / False Directions: On the line beside each statement, write T/TRUE if the statement is correct, or F/FALSE if the statement is incorrect. 8. Smallest dimension should be placed furthest from obj
The statement "Smallest dimension should be placed furthest from obj" is false because the smallest dimension should be placed closest to the object.
When arranging objects, it is important to consider the perspective and depth perception. Placing the smallest dimension closest to the object helps create a sense of depth and makes the object appear more three-dimensional. This technique is often used in art and design to enhance the visual impact of an object or composition.
For example, when drawing a cube, the smaller sides should be placed towards the front to create the illusion of depth. Therefore, it is incorrect to place the smallest dimension furthest from the object.
Learn more about dimension https://brainly.com/question/32980926
#SPJ11
Use Cramer's rule to solve the following linear system of equations: x + 2y = 2 2xy + 3z = 0 x+y=0
The solution to the linear system of equations using Cramer's rule is x = 1, y = -1, and z = 0.
Cramer's rule is a method used to solve systems of linear equations by using determinants. In this case, we have three equations with three variables: x, y, and z. To solve the system using Cramer's rule, we need to calculate three determinants.
The first step is to find the determinant of the coefficient matrix, which is the matrix formed by the coefficients of the variables. In this case, the coefficient matrix is:
| 1 2 0 |
| 2 0 3 |
| 1 1 0 |
To find the determinant of this matrix, we can use the formula:
det(A) = a11(a22a33 - a23a32) - a12(a21a33 - a23a31) + a13(a21a32 - a22a31),
where aij represents the elements of the matrix. By substituting the values from our coefficient matrix into the formula, we can calculate the determinant.
The second step is to find the determinants of the matrices obtained by replacing the first column of the coefficient matrix with the constants from the right-hand side of the equations. In this case, we have three determinants to find: Dx, Dy, and Dz.
Dx =
| 2 2 0 |
| 0 0 3 |
| 0 1 0 |
Dy =
| 1 2 0 |
| 2 0 3 |
| 1 0 0 |
Dz =
| 1 2 0 |
| 2 0 0 |
| 1 1 0 |
By calculating these determinants using the same formula as before, we can obtain the values of Dx, Dy, and Dz.
The final step is to find the values of x, y, and z by dividing each determinant (Dx, Dy, Dz) by the determinant of the coefficient matrix (det(A)). This gives us the solutions for the system of equations.
Learn more about : Equations
brainly.com/question/14123439
#SPJ11
14 pts Question 9 A sedimentation tank is designed to settle 85% of particles with the settling velocity of 1 m/min. The retention time in the tank will be 12 min. If the flow rate is 15 m³/min, what should be the depth of this tank in m?
The depth of the tank should be 12 meters to allow for the settling of 85% of particles within the given retention time.
To calculate the depth of the sedimentation tank, we need to determine the settling distance required for particles to settle within the given retention time. The settling distance can be calculated using the settling velocity and retention time.
The settling distance (S) can be calculated using the formula:
S = V × t
Where:
S = Settling distance
V = Settling velocity
t = Retention time
In this case, the settling velocity (V) is given as 1 m/min and the retention time (t) is given as 12 min. Using these values, we can calculate the settling distance:
S = 1 m/min × 12 min = 12 meters
The settling distance represents the depth of the sedimentation tank. Therefore, to allow for the settling of 85% of particles within the allotted retention time, the tank's depth should be 12 metres.
Learn more about distance on:
https://brainly.com/question/12356021
#SPJ11
PARTIAL DIFFERENTIAL EQUATIONS
Answer:
Solve u, u for 0≤x≤, given u(0,t)=0, u(x,t) = 0, u(x,0) = 10 sin.x. =
2. u(x,t) = 10e¹sin x
Partial differential equations (PDEs) are mathematical expressions used to describe various physical phenomena such as waves, heat, or electrostatics.
To solve the given problem, we'll use the method of separation of variables.
Let's assume that u(x, t) can be expressed as the product of two functions: X(x) and T(t).
Substituting this into the PDE, we obtain two separate equations: one involving X(x) and the other involving T(t).
Solving the equation for X(x), we find X(x) = 0, which implies that X(x) is identically zero.
Solving the equation for T(t), we find T(t) = Ce^(-λ^2t), where C is a constant and λ^2 is a separation constant.
Applying the given boundary condition u(x, 0) = 10sin(x), we can determine the value of λ^2 and find that T(t) = e^(t) is the solution for T(t).
Combining X(x) = 0 and T(t) = e^(t), we get u(x, t) = 0 as the general solution.
However, there seems to be an error in the second part of the problem statement. It states that u(x, t) = 10e^(1)sin(x), which contradicts the initial condition u(x, 0) = 10sin(x).
Thus, the correct general solution is u(x, t) = 0.
To know more about mathematical visit:
https://brainly.com/question/27235369
#SPJ11
Exercise #2: If 12 Kg of fluid/min passes through a reversible steady state process. The inlet properties of the fluid are: P₁ = 1.8 bar, p₁ = 30 Kg/m³, C₁ = 120 m/s, and U₁ = 1100 Kj/Kg. Fur
The steady-state work for the given reversible steady-state process, is found to be 2.304 W.
Given information: 12 Kg of fluid/min passes through a reversible steady-state process, and the inlet properties of the fluid are P₁ = 1.8 bar, p₁ = 30 Kg/m³, C₁ = 120 m/s, and U₁ = 1100 Kj/Kg.
The formula for steady-state flow energy is given by:-
ΔH = W + Q
For reversible steady state flow, ΔH = 0. Thus,
W = -Q
The formula for steady-state work is given by:-
W = mṁ(h₂ - h₁)
where mṁ is the mass flow rate,h₁ and h₂ are the specific enthalpy at the inlet and exit, respectively,To find out h₂ we need to use the following formula:-
h₂ = h₁ + (V₂² - V₁²)/2 + (u₂ - u₁)
where V₁ and V₂ are the specific volumes, respectively, and u₁ and u₂ are the internal energies at the inlet and exit, respectively.To get V₂ we use the formula given below:-
V₂ = V₁ * (P₂/P₁) * (T₁/T₂)
where P₂ is the pressure at the exit, T₁ is the temperature at the inlet, and T₂ is the temperature at the exit,For a reversible adiabatic process, Q = 0. Thus,
W = -ΔH = -mṁ * (h₂ - h₁)
= mṁ * (h₁ - h₂)
The final formula for steady-state work can be given by:-
W = mṁ * [(V₂² - V₁²)/2 + (u₂ - u₁)]
W = (12 kg/min) * [((0.016102 m³/kg)² - (0.033333 m³/kg)²)/2 + (2900 J/kg - 1100 J/kg)]
W = 12(11.52)
W = 138.24 J/min
= 2.304 W
Know more about the steady-state process,
https://brainly.com/question/15726481
#SPJ11
6. Simplify: (3√5-5√2)(4√5 + 3√2).
Answer:
30 - 11√10----------------------------
Simplify by distribution:
(3√5 - 5√2)(4√5 + 3√2) = (3√5)(4√5) + (3√5)(3√2) - (5√2)(4√5) - (5√2)(3√2) = 12*5 + 9√10 - 20√10 - 15*2 = 60 - 30 - 11√10 = 30 - 11√10You are a production technician at "Proteins 'R Us' and have just run out of HIC chromatography equilibration buffer. Describe in detail how you would prepare the following buffer. 10 points (please show calculation and description how would you make this buffer?) You need 100 mL of. 20mM Sodium Phosphate, 2M ammonium sulfate, pH 7.0 You have the following reagents to make this buffer: 1. 100mM sodium phosphate dibasic 2. 100mM sodium phosphate monobasic 3. Ammonium sulfate powder stock (132.14 g/mol)
Answer:
To prepare the 100 mL of 20 mM Sodium Phosphate, 2 M ammonium sulfate buffer with a pH of 7.0, we will need to calculate the amounts of the reagents required and then proceed with the preparation.
Here's a step-by-step guide (Explanation):
Step 1: Calculate the amount of 100 mM sodium phosphate dibasic required. The molar mass of Na2HPO4 is 141.96 g/mol.
The molecular weight of this substance is calculated as follows:
100 mM Na2HPO4 = 0.1 L × 100 mmol/L × 141.96 g/mol= 1.4196 g of Na2HPO4 is required.
Step 2: Calculate the amount of 100 mM sodium phosphate monobasic required. The molar mass of NaH2PO4 is 119.98 g/mol.
The molecular weight of this substance is calculated as follows:
100 mM NaH2PO4 = 0.1 L × 100 mmol/L × 119.98 g/mol= 1.1998 g of NaH2PO4 is required.
Step 3: Dissolve 1.4196 g of Na2HPO4 and 1.1998 g of NaH2PO4 in 70 mL of deionized water in a beaker. Stir the solution until the solutes have dissolved entirely. Make sure that the pH is 7.0.
Step 4: Using a calculator, calculate the mass of ammonium sulfate required to make a 2 M solution of ammonium sulfate. The molar mass of (NH4)2SO4 is 132.14 g/mol.
The molecular weight of this substance is calculated as follows:
2 M (NH4)2SO4 = 2 mol/L × 132.14 g/mol= 264.28 g is the mass of (NH4)2SO4 required to prepare a 2 M solution.
Step 5: To the beaker containing the sodium phosphate solution, add 30 mL of deionized water and mix well. Add 2 M ammonium sulfate in increments until the solution is homogeneous. Make sure that the final volume of the solution is 100 mL. Check the pH to ensure that it is still 7.0. If necessary, make small adjustments to the ph.
Notes:
The calculation of the molecular weight of the Na2HPO4 and NaH2PO4 is as follows:
Na2HPO4 = (22.99 + 22.99 + 30.97 + 64.00 + 64.00) g/mol
Na2HPO4 = 141.96 g/mol
NaH2PO4 = (22.99 + 1.01 + 30.97 + 64.00 + 64.00) g/mol
NaH2PO4 = 119.98 g/mol
To know more about molecular weight visit:
https://brainly.com/question/20380323
#SPJ11