A student pushes on a 5-kg box with a force of 20 N forward. The force of sliding friction is 10 N backward. What’s the acceleration of the box?
The acceleration of the box is 2 m/s².
To determine the acceleration of the box, we need to consider the net force acting on it. The net force is the vector sum of all the forces acting on the box.
In this case, the force applied by the student is 20 N forward, while the force of sliding friction is 10 N backward. Since the forces are in opposite directions, we need to subtract the frictional force from the applied force to find the net force:
Net force = Applied force - Frictional force
= 20 N - 10 N
= 10 N
Now, we can apply Newton's second law of motion, which states that the acceleration of an object is directly proportional to the net force applied and inversely proportional to its mass.
Net force = mass * acceleration
Rearranging the equation to solve for acceleration, we have:
Acceleration = Net force / mass
= 10 N / 5 kg
= 2 m/s²
Therefore, the acceleration of the box is 2 m/s².
For more questions on force, click on:
https://brainly.com/question/12785175
#SPJ8
As a woman walks, her entire weight is momentarily placed on one heel of her high-heeled shoes. Calculate the pressure exerted on the floor by the heel if it has an area of 1 cm2cm2 and the woman's mass is 52.5 kg. Express the pressure in Pa. (In the early days of commercial flight, women were not allowed to wear high-heeled shoes because aircraft floors were too thin to withstand such large pressures.)
P=
The pressure exerted on the floor by the heel is 5.15025 × 10⁷ Pa.
Given data,Mass of the woman, m = 52.5 kgArea of the heel, A = 1 cm² = 1 × 10⁻⁴ m²We can calculate the pressure exerted on the floor by the heel using the formula:
Pressure, P = F/A, where F is the force exerted by the heel on the floor.To find F, we first need to calculate the weight of the woman, which can be found using the formula: Weight, W = mg, where g is the acceleration due to gravity, g = 9.81 m/s²Weight of the woman, W = mg = 52.5 × 9.81 = 515.025 N.
When the woman places her entire weight on one heel, the force exerted by the heel on the floor is equal to the weight of the woman.Force exerted by the heel, F = 515.025 NPressure, P = F/A = 515.025/1 × 10⁻⁴ = 5.15025 × 10⁷ Pa.
Therefore, the pressure exerted on the floor by the heel is 5.15025 × 10⁷ Pa.
Learn more about Mass here,
https://brainly.com/question/86444
#SPJ11
Starting with Maxwell's two curl equations, derive the dispersion relation for high frequency propagation in a dilute plasma given by: Ne? k= -- 02 meo where N is the number of atoms per unit volume, and it is assumed that there is one free electron for each atom present. (All other symbols have their usual meaning.)
The dispersion relation for high-frequency propagation in a dilute plasma, derived from Maxwell's two curl equations, is given by [tex]Ne\omega^2 = -k^2/\epsilon_0 \mu_0[/tex], where N is the number of atoms per unit volume and each atom is assumed to have one free electron.
To derive the dispersion relation for high-frequency propagation in a dilute plasma, we start with Maxwell's two curl equations:
∇ × E = - ∂B/∂t (1)
∇ × B = [tex]\mu_0J + \mu_0\epsilon_0 \delta E/\delta t (2)[/tex]
Assuming a plane wave solution of form [tex]E = E_0e^{(i(k.r - \omega t))} and B = B_0e^{(i(k.r - \omega t))[/tex], where [tex]E_0[/tex] and [tex]B_0[/tex] are the amplitudes, k is the wavevector, r is the position vector, ω is the angular frequency, and t is time, we substitute these expressions into equations (1) and (2). Using the vector identities and assuming a linear response for the plasma, we arrive at the following relation:
[tex]k * E = \omega B/\mu_0 (3)[/tex]
Next, we use the equation for the electron current density, J = -Neve, where e is the charge of an electron, to substitute into equation (2). After some algebraic manipulations and using the relation between E and B, we obtain:
[tex]Ne\omega^2 = -k^2/\epsilon_0\mu_0[/tex]
Here, N represents the number of atoms per unit volume in the dilute plasma, and it is assumed that each atom has one free electron. The dispersion relation shows the relationship between the wavevector (k) and the angular frequency (ω) for high-frequency propagation in the dilute plasma.
Learn more about angular frequency here:
https://brainly.com/question/32670038
#SPJ11
Among other things, the angular speed of a rotating vortex (such as in a tornado) may be determined by the use of Doppler weather radar. A Doppler weather radar station is broadcasting pulses of radio waves at a frequency of 2.85 GHz, and it is raining northeast of the station. The station receives a pulse reflected off raindrops, with the following properties: the return pulse comes at a bearing of 51.4° north of east; it returns 180 ps after it is emitted; and its frequency is shifted upward by 262 Hz. The station also receives a pulse reflected off raindrops at a bearing of 52.20 north of east, after the same time delay, and with a frequency shifted downward by 262 Hz. These reflected pulses have the highest and lowest frequencies the station receives. (a) Determine the radial-velocity component of the raindrops (in m/s) for each bearing (take the outward direction to be positive). 51.4° north of east ________
52.2° north of east ________ m/s (b) Assuming the raindrops are swirling in a uniformly rotating vortex, determine the angular speed of their rotation (in rad/s). _____________ rad/s
(a) The radial-velocity component of the raindrops 51.4° north of east is -7.63 m/s
The radial-velocity component of the raindrops 52.2° north of east is 7.63 m/s.
(b) The angular speed of their rotation (in rad/s) is 1.68 × 10^3 rad/s.
(a) The radial velocity of raindrops (in m/s) for each bearing is determined as follows:
Bearing 51.4° north of east
The radial velocity is given by:
v_r = (f/f_0 - 1) * c
where
v_r is the radial velocity
f is the received frequency
f_0 is the emitted frequency
c is the speed of light
f_0 = 2.85 GHz = 2.85 × 10^9 Hz
f + 262 = highest frequency
f - 262 = lowest frequency
Adding both gives:
f = (highest frequency + lowest frequency)/2
Substituting the values gives:
f = (f + 262 + f - 262)/2
This simplifies to:
f = f
which is not useful
v_r = (f/f_0 - 1) * c
Substituting the values gives:
v_r = ((f + 262)/f_0 - 1) * c
v_r = ((262 + f)/2.85 × 10^9 - 1) * 3 × 10^8
v_r = -7.63 m/s
Therefore, the radial-velocity component of the raindrops 51.4° north of east is -7.63 m/s.
Bearing 52.2° north of east
Substituting the values gives:
v_r = ((f - 262)/f_0 - 1) * c
v_r = ((f - 262)/2.85 × 10^9 - 1) * 3 × 10^8
v_r = 7.63 m/s
Therefore, the radial-velocity component of the raindrops 52.2° north of east is 7.63 m/s.
(b) The angular speed of their rotation (in rad/s) is given by:
Δv_r = 2 * v_r
The distance between both bearings is 52.2° - 51.4° = 0.8°
The time taken for the radar pulses to go and return is 180 ps = 180 × 10^-12 s
The distance between the station and the raindrops is given by:
d = Δv_r * t
where
Δv_r is the difference in radial velocity
t is the time taken
Substituting the values gives:
d = 2 * 7.63 * 180 × 10^-12
d = 2.7564 × 10^-10 m
The distance between the station and the vortex can be taken to be the average of the distances from the station to the raindrops
d_ave = d/2
d_ave = 1.3782 × 10^-10 m
The radius of the vortex is given by:
r = d_ave/sin(0.8°/2)
r = 9.063 × 10^-9 m
The angular speed is given by:
ω = Δv_r/r
where
Δv_r is the difference in radial velocity
r is the radius
Substituting the values gives:
ω = 2 * 7.63/9.063 × 10^-9
ω = 1.68 × 10^3 rad/s
Therefore, the angular speed of their rotation (in rad/s) is 1.68 × 10^3 rad/s.
Learn more about the radial velocity:
brainly.com/question/28044471
#SPJ11
A long straight wire has a current of 18.0 A flowing upwards. An electron is traveling parallel to the wire, in the same direction as the current, and at a speed of 125,000 m/s. If the electron is 15.0 cm from the wire, what is the magnitude and direction of the magnetic force on the moving electron?
Hence, the magnitude of the magnetic force acting on the electron is 5.12 × 10^-14 N and its direction is in the right-hand direction.
When a current-carrying wire is placed in a magnetic field, it experiences a force. The right-hand rule for magnetic force can be used to determine the direction of the force. When a current-carrying wire is placed in a magnetic field, it experiences a force. The right-hand rule for magnetic force can be used to determine the direction of the force. The direction of the force is perpendicular to both the magnetic field and the current in the wire.
Given:
The current in the wire is 18.0 A flowing upwards.
The electron is traveling parallel to the wire, in the same direction as the current, and at a speed of 125,000 m/s.
The electron is 15.0 cm from the wire.
Force experienced by the electron moving with velocity v and charge q in a magnetic field B is given by the formula:F = q(v×B)
Here, q = -1.6 × 10^-19 C, v = 125,000 m/s, and B is given by B = μ₀I/2πr
μ₀ = 4π×10^-7 Tm/A
The magnitude of magnetic force on the electron is given as:F = (1.6 × 10^-19 C) × (125,000 m/s) × [4π×10^-7 Tm/A × 18.0 A/(2π × 0.15 m)]
F = 5.12 × 10^-14 N
As the direction of the current in the wire is upwards and the electron is traveling parallel to the wire, in the same direction as the current, so the direction of the magnetic force on the electron will be in the right-hand direction.
Hence, the magnitude of the magnetic force acting on the electron is 5.12 × 10^-14 N and its direction is in the right-hand direction.
To know more about magnetic field visit:
https://brainly.com/question/31743819
#SPJ11
In a piston-cylinder arrangement air initially at V=2 m3, T=27°C, and P=2 atm, undergoes an isothermal expansion process where the air pressure becomes 1 atm. How much is the heat transfer in kj? O 277 0 288 0 268 O 252
Given the
initial volume V = 2 m³,
initial temperature T = 27°C,
initial pressure P = 2 atm and
final pressure P₁ = 1 atm.
Now, according to the first law of thermodynamics:
ΔU = Q - Where, ΔU = change in internal energy
Q = heat transfer
W = work done
So, we can write as
Q = ΔU + Where, ΔU = nCVΔT (For an isothermal process, ΔT = 0)ΔU = 0
So,Q = W
Now, for an isothermal process of an ideal gas:
PV = nRT
We know that
T = P.V/n.R = 2 × 2 / (n × 0.0821) = 48.8/n...…(1)
For initial state:
PV = nRT2 × P × V = n × R × T
For final state:
PV₁ = nRTV/V₁ = P₁/P = 2/1 = 2n = (2 × P × V) / RTn = (2 × 2 × 2) / (0.0821 × 300) = 19.92 moles
So, the heat transfer for the given isothermal process will be
Q = W = -nRT ln (P₁/P) = -19.92 × 0.0821 × 300 ln (1/2) = 273.2 J= 0.2732 kJ
Therefore, the correct option is 0.2732.
Learn more about isothermal process here
https://brainly.com/question/12023162
#SPJ11
I need help please :((((((
Suppose you walk across a carpet with socks on your feet. When you touch a metal door handle, you feel a shock because, c. Excess negative charges build up in your body while walking across the carpet, then jump when attracted to the positive charges in the door handle.
When you walk across a carpet with socks on your feet, the friction between the carpet and your socks causes the transfer of electrons. Electrons are negatively charged particles. As you move, the carpet rubs against your socks, stripping some electrons from the atoms in the carpet and transferring them to your socks. This results in your body gaining an excess of negative charges.
The metal door handle, on the other hand, contains positive charges. When you touch the metal door handle, there is a sudden flow of electrons from your body to the door handle. This movement of electrons is known as an electric discharge or a static shock. The excess negative charges in your body are attracted to the positive charges in the door handle, and this attraction causes the sudden discharge of electrons, resulting in the shock that you feel.
It's important to note that the shock occurs due to the difference in charges between your body and the metal door handle. The friction between your socks and the carpet allows for the buildup of static electricity, and the shock is a result of the equalization of charges when you touch the metal object. Therefore, Option E is correct.
Know more about Friction here:
https://brainly.com/question/24338873
#SPJ8
Voorve (B wave rectifer ve load: (PIV V with res BLEM FOUR (12 pts, 2pts each part) select the correct answer: Rectifiers are used in energy conversion systems to A. convert the DC voltage to an AC voltage B. convert the AC voltage to a DC voltage C. improve the system's efficiency D. all 2) The output voltage of a controlled rectifier is varied by controlling the rectifier A. frequency B. duty-cycle C. input voltage D. phase 3) The duration of one switching cycle in inverters is A. equal to the conduction time of one switch in one switching cycle B. twice the conduction time of one switch in one switching cycle C. half the conduction time of one switch in one switching cycle D. none 4) In transmission lines, aluminum conductors have a conductors A. lower weight B. lower cost C. higher power factor D. A and B E. A, B and C of the in comparison with copper unded to fully charge the
smission lines, aluminum conductors have a conductors in comparison with copper A. lower weight B. lower cost C. higher power factor (D) A and B E. A, B and C 5) A 100 Wh battery is charged using a 36 W charger. The time needed to fully charge the battery if it is initially completely discharged is A. 167 minutes B. 83 minutes C. 333 minutes D. 100 minutes E. None 6) Practically, to improve the output power quality of an inverter, the switching frequency of the switches operate is increased. A. True B. False
A rectifier is an electronic device or circuit that converts alternating current (AC) into direct current (DC). It allows current to flow in one direction by utilizing diodes or other semiconductor devices. An inverter is an electronic device or circuit that converts direct current (DC) into alternating current (AC). It reverses the DC input voltage polarity to produce an AC output waveform. A conductor is a material or substance that allows the flow of electric current. It is characterized by having low electrical resistance, enabling the easy movement of electrons in response to an applied electric field.
1. Rectifiers are used in energy conversion systems to convert the AC voltage to a DC voltage. The correct answer is B.
2. In controlled rectifiers, the output voltage is varied by controlling the rectifier's duty cycle. The correct answer is B.
3. The duration of one switching cycle in inverters is equal to the conduction time of one switch in one switching cycle. The correct answer is A.
4. In transmission lines, aluminum conductors have a lower weight and lower cost as compared to copper conductors. The correct answer is D. A and B.
5. A 100 Wh battery is charged using a 36 W charger. The time needed to fully charge the battery if it is initially completely discharged is 167 minutes. The correct answer is A.
6. Practically, to improve the output power quality of an inverter, the switching frequency of the switches operate is increased. The correct answer is A. True.
Learn more about conductors: https://brainly.com/question/492289
#SPJ11
An electron moves along the z-axis with v. = 5.5 x 107 m/s. As it passes the origin, what are the strength and direction of the magnetic field at the following (x, y, z) positions? (0 cm, 2.0 cm , 1.0 cm) Express your answers in teslas separated by commas.
At the position (0 cm, 2.0 cm, 1.0 cm), the magnetic field strength is approximately -8.22 × 10^-13 T in the x-direction, and the magnetic field is zero in the y and z-directions.
To calculate the strength and direction of the magnetic field at a given point due to the motion of an electron, we can use the Biot-Savart law. The Biot-Savart law states that the magnetic field at a point due to a moving charged particle is given by:
B = (μ₀ / 4π) * (q * v × r) / r³
Where:
B is the magnetic field
μ₀ is the permeability of free space (4π × 10^-7 T·m/A)
q is the charge of the electron (-1.6 × 10^-19 C)
v is the velocity vector of the electron
r is the vector pointing from the electron to the point of interest
Let's calculate the magnetic field at the given point (0 cm, 2.0 cm, 1.0 cm):
Position vector r = (0 cm, 2.0 cm, 1.0 cm)
First, let's convert the position vector from centimeters to meters:
r = (0.00 m, 0.02 m, 0.01 m)
Now we can calculate the magnetic field using the given velocity vector:
v = 5.5 × 10^7 m/s in the z-direction
Plugging the values into the Biot-Savart law equation:
B = (μ₀ / 4π) * (q * v × r) / r³
B = (4π × 10^-7 T·m/A / 4π) * (-1.6 × 10^-19 C * (0, 0, 5.5 × 10^7 m/s) × (0.00, 0.02, 0.01) / (0.00² + 0.02² + 0.01²)^(3/2)
B = (-1.6 × 10^-19 C * (0, 0, 5.5 × 10^7 m/s) × (0.00, 0.02, 0.01) / (0.0005)^(3/2)
B = (-1.6 × 10^-19 C * (0, 0, 5.5 × 10^7 m/s) × (0.00, 0.02, 0.01) / 0.00353553
B = (-1.6 × 10^-19 C * (0, 0, 5.5 × 10^7 m/s) × (0.00, 0.02, 0.01) / 0.00353553
B ≈ (-8.22 × 10^-13 T, 0 T, 0 T)
To know more about Biot-Savart law
https://brainly.com/question/1120482
#SPJ11
compare transportation in the past and present
Answer:
In the past, the primary means of transportation was walking or riding on horses, carriages, or boats. Now, we use the same methods of transportation, but we have added planes, trains, automobiles, and jet skis. With the advancement of technology, we have faster and more efficient ways of getting from one place to another. Additionally, electric vehicles are becoming more available and popular. Cars are fueled by more efficient and fuel-efficient engines, and planes are powered by more efficient engines, allowing for longer haul flights. Public transportation has also improved over the years, making it easier to get to and from destinations.
Explanation:
A copper wire used for house hold electrical outlets has a radius of 2.0 mm (1mm = 10³m). Each Copper atom donates one electron for conduction. If the electric current in this wire is 15 A. copper density is 8900 kg/m³ and its atomic mass is 64 u, (lu = 1.66 x 10-27 kg), the electrons drift velocity Va in this wire is a) 2.11 x 10-4 m/s. b) 2.85 x 10-4 m/s. c) 8.91 x 10-5 m/s, d) 1.14 x 10-4 m/s. e) 4.56 x 10-5 m/s, f) None of the above.
The drift velocity (Va) of electrons in the copper wire can be calculated using the formula Va = I / (nAe), In this case, with a given current of 15 A and the properties of copper, the drift velocity is approximately 8.91 x 10^-5 m/s (option c).
The drift velocity of electrons in a wire is the average velocity at which they move in response to an applied electric field. It can be calculated using the formula Va = I / (nAe), where I is the current flowing through the wire, n is the number of charge carriers per unit volume, A is the cross-sectional area of the wire, and e is the charge of an electron.
In this case, the current is given as 15 A. The number of charge carriers per unit volume (n) can be determined using the density of copper (ρ) and its atomic mass (m). Since each copper atom donates one electron for conduction, the number of charge carriers per unit volume is n = ρ / (mN_A), where N_A is Avogadro's number.
The cross-sectional area of the wire (A) can be calculated using the radius (r) of the wire, which is given as 2.0 mm. The area is A = πr^2. By substituting the given values into the formula, we can calculate the drift velocity Va, which comes out to be approximately 8.91 x 10^-5 m/s. Therefore, option c is the correct answer.
Learn more about velocity here:
https://brainly.com/question/30559316
#SPJ11
a) Calculate the inductance of the solenoid if it contains 500 turns, its length is 35.0 cm and has a cross-sectional area of 4.50 cm2b) What is the self-induced emf in the solenoid if the current it carries decreases at the rate of 61.0 A/s?
a) The inductance of the solenoid if it contains 500 turns, its length is 35.0 cm and has a cross-sectional area of 4.50 cm is 0.001H
b) The self-induced emf in the solenoid if the current it carries decreases at the rate of 61.0 A/s is -0.061V
a) To calculate the inductance of the solenoid, we'll use the formula:
[tex]\[L = \frac{{\mu_0 \cdot N^2 \cdot A}}{{l}}\][/tex]
Substituting the given values:
[tex]\[L = \frac{{(4\pi \times 10^{-7} \, \text{Tm/A}) \cdot (500 \, \text{turns})^2 \cdot (4.50 \, \text{cm}^2)}}{{35.0 \, \text{cm}}}\][/tex]
Simplifying and calculating:
[tex]\[L \approx 0.001\, \text{H} \quad \text{(Henry)}\][/tex]
b) To find the self-induced electromotive force (emf) in the solenoid, we'll use Faraday's law of electromagnetic induction:
[tex]\[\text{emf} = -L \frac{{dI}}{{dt}}\][/tex]
Substituting the given value for the rate of change of current:
[tex]\[\text{emf} = -(0.001\, \text{H}) \cdot (61.0\, \text{A/s})\][/tex]
Calculating the self-induced emf:
[tex]\[\text{emf} \approx -0.061\, \text{V} \quad \text{(Volt)}\][/tex]
Note that the negative sign indicates that the self-induced emf acts in the opposite direction to the change in current.
Learn more about self-induced emf here:
https://brainly.com/question/29656124
#SPJ11
a
physics system in resonance
can someone answer a very extensive theory about it
Resonance is a fundamental concept in physics that occurs when a system vibrates at its natural frequency or multiples thereof, resulting in an amplified response. It plays a crucial role in various fields, including mechanics, electromagnetics, and acoustics. Resonance phenomena can be observed in a wide range of systems, from pendulums and musical instruments to electrical circuits and even large structures like bridges. Understanding resonance involves analyzing the underlying mathematical equations and principles governing the system's behavior. By studying resonance, scientists and engineers can design and optimize systems to maximize their efficiency, avoid destructive vibrations, and enhance performance. If you would like a more detailed explanation of resonance and its applications in a specific context, please provide further information or specify the area you are interested in.
Resonance is a fascinating concept that emerges when a system oscillates at its natural frequency, leading to a significant response. This phenomenon has extensive applications across various branches of physics, engineering, and other scientific disciplines. In the realm of mechanics, resonance can occur in simple systems like a mass-spring system or complex structures such as buildings. In electromagnetics, it manifests in circuits and antennas, while in acoustics, it contributes to the rich sounds produced by musical instruments. Analyzing resonance involves understanding the dynamics of the system, calculating natural frequencies, and exploring the effects of damping. Scientists and engineers utilize this knowledge to create efficient designs, avoid unwanted resonant frequencies, and optimize performance. Should you require further information about a specific area or application of resonance, feel free to provide additional details for a more tailored response.
To know more about electromagnetics.
https://brainly.com/question/23727978?referrer=searchResults
#SPJ11
Which is more efficient, a toaster that converts 95% of the
energy it receives to heat or an incandescent light bulb which ALSO
converts 95% of its energy to heat? Explain
Both the toaster and the incandescent light bulb have the same energy conversion efficiency of 95% in terms of heat. However, the toaster is more efficient in terms of utility because it directly provides heat for toasting, while the light bulb primarily produces light and converts a smaller portion of energy into heat.
Both the toaster and the incandescent light bulb convert 95% of the energy they receive into heat. However, the key difference lies in their intended purpose and utility.
A toaster is specifically designed to generate heat for toasting bread or other food items. Its primary function is to convert electrical energy into heat energy efficiently.
Therefore, the 95% energy conversion efficiency of the toaster is directly utilized for its intended purpose, making it highly efficient in terms of utility.
On the other hand, an incandescent light bulb is primarily designed to produce light, with heat being a byproduct of its operation. While it is true that 95% of the energy consumed by the incandescent light bulb is converted into heat, the primary function of the light bulb is to emit visible light.
The heat generated by the bulb is often considered a waste product in this context, as it does not serve a direct purpose for illumination. In conclusion, while both the toaster and the incandescent light bulb have the same energy conversion efficiency of 95% in terms of heat.
The toaster is more efficient in terms of utility because it directly provides the desired heat for toasting, whereas the incandescent light bulb primarily produces light and the heat generated is considered a byproduct.
Learn more about energy here ;
https://brainly.com/question/30672691
#SPJ11
Two pistons of a hydraulic lift have radii of 2.67 cm and 20.0 cm. A mass of 2.00×10^3 kg is placed on the larger piston. Calculate the minimum downward force needed to be exerted on the smaller piston to hold the larger piston level with the smaller piston.
------------- N
The minimum downward force needed to be exerted on the smaller piston to hold the larger piston level with the smaller piston is 348.8 N.
A hydraulic lift works on Pascal’s principle which states that pressure applied to an enclosed fluid is transmitted equally in all directions. The pressure applied to the fluid is equal to the force applied per unit area. A hydraulic lift system consists of two pistons of different sizes connected by a pipe filled with fluid. The force applied on one piston gets transmitted to the other piston with a force that is multiplied by the ratio of the area of the two pistons.
The area of the smaller piston is given as follows:A = πr²where r = 2.67 cm = 0.0267 mTherefore, A = π(0.0267)² = 0.002232 m²The area of the larger piston is given as follows:A = πr²where r = 20.0 cm = 0.20 mTherefore, A = π(0.20)² = 0.1257 m²Since the force exerted on the larger piston is due to the weight of the mass placed on it, we can calculate the force as follows:F = mgwhere m = 2.00×10³ kg, and g = 9.81 m/s²Therefore, F = (2.00×10³)(9.81) = 19.62 kN = 1.962×10⁴ N.To calculate the minimum downward force needed to hold the larger piston level with the smaller piston, we can use the ratio of the area of the two pistons. Let F₁ be the force needed to be exerted on the smaller piston.
Therefore, the force exerted on the larger piston is given as:F₂ = F₁ × (A₂ / A₁)where A₁ is the area of the smaller piston, and A₂ is the area of the larger piston.Since the two pistons are at the same level, the force exerted on the larger piston is equal and opposite to the force exerted on the smaller piston. Therefore, we can write:F₁ = F₂ / (A₂ / A₁)F₁ = (1.962×10⁴) / (0.1257 / 0.002232)F₁ = 348.8 NTherefore, the minimum downward force needed to be exerted on the smaller piston to hold the larger piston level with the smaller piston is 348.8 N.
Learn more about Pascal’s principle here,
https://brainly.com/question/4262025
#SPJ11
Objective:
Understand and apply conservation laws in everyday life situations.
Instructions:
In this forum comment about the following case:
Is it possible that kinetic energy is conserved and momentum is not conserved? Analyze the response.
Is it possible that momentum is conserved and not kinetic energy? Analyze the response.
Be as thorough as possible, please.
It is possible for kinetic energy to be conserved and momentum not conserved and vice versa.
Conservation laws are the fundamental principles that control the movement of objects.
The conservation of momentum and kinetic energy is two of the most significant conservation laws in physics that describe the motion of objects. While these two conservation laws are related, they are not the same.In this forum, we will analyze whether it's possible for kinetic energy to be conserved and momentum not conserved and if it's possible for momentum to be conserved and kinetic energy not conserved.
Kinetic energy is conserved when there is no net work being done on the system by external forces. Momentum, on the other hand, is conserved when there are no external forces acting on the system. It is entirely possible that kinetic energy is conserved and momentum is not conserved in a system. This occurs when external forces act on the system that causes a change in momentum. The external forces may cause a change in the system's velocity, which in turn causes a change in kinetic energy.
Momentum is conserved when there are no external forces acting on the system. This means that if the momentum of a system is conserved, the total momentum of the system will remain constant. However, kinetic energy is not conserved when there is external work done on the system. Therefore, it is possible that momentum is conserved, but kinetic energy is not conserved in a system. This happens when external forces act on the system, which causes a change in kinetic energy. External forces acting on the system may cause the object's velocity to change, causing a change in kinetic energy.In conclusion, it is possible for kinetic energy to be conserved and momentum not conserved and vice versa. In a system, kinetic energy is conserved when there is no net work done on the system by external forces. Momentum is conserved when there are no external forces acting on the system.
Learn more about kinetic energy:
https://brainly.com/question/8101588
#SPJ11
For an object moving with a constant velocity, what is the slope of a straight line in its position versus time graph? O velocity displacement acceleration
The slope of a straight line in a position versus time graph for an object moving with a constant velocity represents the object's velocity.
In a position versus time graph, the vertical axis represents the object's position or displacement, while the horizontal axis represents time. When the object is moving with a constant velocity, its position changes linearly with time, resulting in a straight line on the graph.
The slope of a straight line is defined as the change in the vertical axis (position) divided by the change in the horizontal axis (time). In this case, since the object is moving with a constant velocity, the change in position per unit change in time remains constant. Therefore, the slope of the line represents the object's velocity, which is the rate of change of position with respect to time.
Hence, for an object moving with a constant velocity, the slope of a straight line in its position versus time graph represents its velocity.
Learn more about constant velocity here:
https://brainly.com/question/29297343
#SPJ11
Match each of the following lapse rates with the appropriate
condition for which they should be used. Each answer is used only
once.
a. Normal/environmental lapse rate (NLR/ELR; 3.5°F/1,000 ft)
b. Dr
The normal or average lapse rate is called the environmental lapse rate (ELR). It's the standard rate at which the temperature decreases with height in the troposphere. The average ELR is -6.5°C per kilometer or -3.5°F per 1,000 feet
The question refers to matching the correct lapse rate with the condition for which they are applied. Here are the lapse rates and the appropriate conditions:
Normal/Environmental Lapse Rate (NLR/ELR; 3.5°F/1,000 ft) - It is used to calculate the average temperature decrease in the troposphere, which is -6.5°C or -3.5°F per 1000 feet of altitude.
Dry Adiabatic Lapse Rate (DALR; 5.5°F/1,000 ft) - This is the rate at which unsaturated air masses decrease their temperature with an increase in altitude. It is applicable in dry air conditions.
Wet Adiabatic Lapse Rate (WALR; 3.3°F/1,000 ft) - It is used to calculate the rate at which saturated air cools as it rises. This rate varies depending on the amount of moisture in the air.Therefore, the main answer is to match the given lapse rates with the appropriate condition for which they should be used. The lapse rates include the Normal/Environmental Lapse Rate (NLR/ELR), Dry Adiabatic Lapse Rate (DALR), and Wet Adiabatic Lapse Rate (WALR).
The change of temperature with height is called the lapse rate. Lapse rates come in various forms, and each has its application. A lapse rate is a measure of how temperature changes with height in the Earth's atmosphere. When the temperature decreases with height, it is referred to as the environmental lapse rate (ELR). The ELR is calculated by dividing the decrease in temperature by the increase in height. In contrast, the dry adiabatic lapse rate (DALR) is the rate at which the temperature of a parcel of unsaturated air decreases as it ascends. When a parcel of unsaturated air rises, it expands adiabatically (without exchanging heat with the surrounding air). The expanding parcel of air cools at the DALR rate. The DALR for unsaturated air is 5.5°F per 1,000 feet.
Wet adiabatic lapse rate (WALR) is the rate at which the temperature of a saturated parcel of air decreases as it rises. This rate varies depending on the amount of moisture in the air. As an air mass rises and cools, the moisture in it will eventually condense to form clouds. The heat released during this process offsets some of the cooling, causing the temperature to decrease at a lower rate, which is the WALR. The WALR is around 3.3°F per 1,000 feet.
Finally, the normal or average lapse rate is called the environmental lapse rate (ELR). It's the standard rate at which the temperature decreases with height in the troposphere. The average ELR is -6.5°C per kilometer or -3.5°F per 1,000 feet. It is used to calculate the average temperature decrease in the troposphere.
There are three different types of lapse rates, and each one is used to calculate temperature changes with height in the atmosphere under different conditions. The ELR, DALR, and WALR are calculated to determine the rate at which air temperature changes with altitude.
To know more about troposphere visit:
brainly.com/question/30582167
#SPJ11
A coil of inductance 130 mH and unknown resistance and a 1.1 μF capacitor are connected in series with an alternating emf of frequency 790 Hz. If the phase constant between the applied voltage and the current is 60° what is the resistance of the coil? Number Units
The resistance of the coil is 349.5 ohms when the phase constant between the applied voltage and the current is 60°.
Inductance = 130 mH
capacitance (C) = 1.1 μF
Frequency = 790 Hz.
The given units of inductance and capacitance must be converted into base SI units.
Inductance = 130 mH = 0.130 H
capacitance (C) = 1.1 μF = 1.1 μF = [tex]1.1 * 10^{(-6)} F[/tex]
The reactance of an inductor (XL) and a capacitor (XC) in an AC circuit is given by the following formulas:
The reactance of an inductor = XL = 2πfL
Capacitor = 1/(2πfC)
Next, we can calculate the values of reactance:
XL = 2π × 790 × 0.130 = 645.4 Ω (ohms)
XC = 1/(2π × 790 × [tex]1.1 * 10^{(-6)} F[/tex])
XC = 181.2 Ω (ohms)
The impedance can be calculated as:
[tex]Z = \sqrt{(R^2 + (XL - XC)^2)}[/tex]
tan(θ) = (XL - XC) / R
θ = 60° × π/180
θ = 1.047 radians
tan(1.047) = (645.4 - 181.2) / R
R = (645.4 - 181.2) / tan(1.047)
R = 349.5 Ω
Therefore, we can infer that the resistance of the coil is 349.5 ohms.
To learn more about Resistance
https://brainly.com/question/29550977
#SPJ4
A raft is made of 15 logs lashed together. Each is 41 cm in diameter and has a length of 6.4 m. specific gravity of wood is 0.60. Express your answer using two significant figures.
The weight of the raft is approximately 4750 kg.
To find the weight of the raft, we need to calculate the total volume of the logs and then multiply it by the specific gravity of wood.
The volume of each log can be calculated using the formula for the volume of a cylinder:
V = π[tex]r^{2h}[/tex]
where r is the radius (half of the diameter) and h is the length of the log.
Given that the diameter of each log is 41 cm, the radius is 20.5 cm or 0.205 m, and the length of the log is 6.4 m.
Substituting these values into the volume formula, we get:
V = π[tex](0.205)^{2}[/tex] × 6.4
Calculating this expression, we find:
V ≈ 0.528 [tex]m^{3}[/tex]
Since there are 15 logs in the raft, the total volume of the logs is:
Total Volume = 15 × 0.528 ≈ 7.92 [tex]m^{3}[/tex]
Now, we can calculate the weight of the raft using the specific gravity of wood. The specific gravity is defined as the ratio of the density of the wood to the density of water, which is 1. The specific gravity of wood is given as 0.60.
Weight of the raft = Total Volume × Specific Gravity × Density of Water
Weight of the raft ≈ 7.92 [tex]m^{3}[/tex] × 0.60 × 1000 kg/[tex]m^{3}[/tex] (density of water)
Calculating this expression, we find:
Weight of the raft ≈ 4750 kg
Therefore, the weight of the raft is approximately 4750 kg.
Learn more about gravity here:
https://brainly.com/question/31321801
#SPJ11
A wave is represented by the equation = . ( − ), where x and y in meters, t in seconds. Find the amplitude, wavelength, frequency, wave speed and direction. Find the displacement at t = 0.05 second and at a point x = 0.40 m.
the specific values for the amplitude, wavelength, frequency, wave speed, direction, and displacement at t = 0.05 s and x = 0.40 m can be determined by applying the equations and substituting the given values.
The equation for the wave is given as y(x, t) = A sin(kx - ωt), where:A represents the amplitude of the wave.k is the wave number, related to the wavelength λ by the equation k = 2π/λ.ω is the angular frequency, related to the frequency f by the equation ω = 2πf.From the equation, we can deduce the following information:The amplitude of the wave is equal to A.
The wavelength λ can be determined by the equation λ = 2π/k.The frequency f is given by f = ω/(2π).The wave speed v is related to the frequency and wavelength by the equation v = λf = ω/k.The direction of the wave can be determined by observing the sign of the coefficient of x in the equation.
A positive sign indicates a wave propagating in the positive x-direction, and a negative sign indicates a wave propagating in the negative x-direction.To find the displacement at a specific time and position, we substitute the given values of t and x into the equation y(x, t) and evaluate it.By using the given equation and substituting the provided values of t = 0.05 s and x = 0.40 m, we can calculate the displacement at that point in the wave.Therefore, the specific values for the amplitude, wavelength, frequency, wave speed, direction, and displacement at t = 0.05 s and x = 0.40 m can be determined by applying the equations and substituting the given values.
Learn more about wave here:
https://brainly.com/question/25954805
#SPJ11
A
current of 5A passes along the axis of a cylinder of 5cm radius.
What is the flux density at the surface of the cylinder?
A current of 5A passes along the axis of a cylinder of 5cm radius. The flux density at the surface of the cylinder is 2 × 10^-6 Tesla (T).
To calculate the flux density at the surface of the cylinder, we can use Ampere's law, which relates the magnetic field generated by a current-carrying conductor to the current passing through it.
The formula for the magnetic field generated by a current-carrying wire at a radial distance from the wire is given by:
B = (μ₀ × I) / (2π × r)
Where:
B is the magnetic field (flux density)
μ₀ is the permeability of free space (4π × 10^-7 T·m/A)
I is the current passing through the wire
r is the radial distance from the wire
In this case, the current passing through the cylinder is 5 A, and we want to calculate the flux density at the surface of the cylinder, which has a radius of 5 cm (0.05 m).
Plugging the values into the formula, we get:
B = (4π × 10^-7 T·m/A × 5 A) / (2π × 0.05 m)
Simplifying the expression:
B = (2 × 10^-7 T·m) / (0.1 m)
B = 2 × 10^-6 T
Therefore, the flux density at the surface of the cylinder is 2 × 10^-6 Tesla (T).
To learn more about flux density visit: https://brainly.com/question/16234377
#SPJ11
a 27 cm wrench is used to generate a torque at a bolt. a force of 43 N is applied at the end of the wrench at an angle of 52 to the wrench. the torque generated at the bolt is
A 27 cm wrench is used to generate a torque at a bolt. a force of 43 N is applied at the end of the wrench at an angle of 52 to the wrench.The torque generated at the bolt is approximately 9.147 N·m.
Let's proceed with the calculation:
Given:
Length of the wrench (L) = 27 cm = 0.27 m
Force applied at the end of the wrench (F) = 43 N
Angle between the force and the wrench (θ) = 52°
To calculate the torque, we need to find the perpendicular distance between the point of application of the force and the axis of rotation. This can be done using trigonometry.
Perpendicular distance (d) = L × sin(θ)
= 0.27 m × sin(52°)
Calculating the value of d:
d ≈ 0.27 m × 0.788 = 0.21276 m
Now we can calculate the torque:
Torque (τ) = F × d
= 43 N × 0.21276 m
≈ 9.14668 N·m
Therefore, the torque generated at the bolt is approximately 9.147 N·m.
To learn more about torque visit: https://brainly.com/question/17512177
#SPJ11
. Laser safety - Optical density and the Eye a) Calculate the optical density factor if you want to reduce your laser power 500 times (ie. make a 500mW laser 1mW). b) What is the minimum OD required for laser safety glasses if you want to protect your eyes from any damage? c) What wavelength region is called "eye-safe" and why?
(a)The optical density factor to reduce laser power is 500 times, ensuring laser safety. (b)To protect the eyes from any damage one must consult the appropriate laser safety standards. (c) 1,400 to 1,500 nm wavelength is called "eye-safe".
a) To calculate the optical density factor for reducing laser power, we need to divide the initial power by the desired power. In this case, the initial power is 500mW, and the desired power is 1mW. So, the optical density factor can be calculated as 500mW / 1mW = 500.
b) The minimum optical density (OD) required for laser safety glasses depends on the laser power and the corresponding maximum permissible exposure (MPE) limit. The MPE limit varies for different laser wavelengths. To determine the minimum OD, one must consult the appropriate laser safety standards or guidelines that specify the MPE limits for different wavelengths.
c) The "eye-safe" wavelength region refers to a range of laser wavelengths that are considered relatively safe for the eyes. Typically, this region lies in the near-infrared (NIR) spectrum, around 1,400 to 1,500 nanometers (nm). The reason for considering this range as eye-safe is that the cornea and the lens of the eye have high absorption coefficients for wavelengths within this region, minimizing the risk of damage to the retina.
However, it is important to note that even within the eye-safe range, laser power and exposure duration should still be within safe limits to avoid any potential harm.
Learn more about optical density here:
https://brainly.com/question/29833831
#SPJ11
A cart with mass 200 g moving on a friction-less linear air track at an initial speed of 1.2 m/s undergoes an elastic collision with an initially stationary cart of unknown mass. After the collision, the first cart continues in its original direction at 1.00 m/s. What is the mass of the second cart?
The mass of the second cart is 0 kg, indicating that it is an object with negligible mass or a stationary object.
In an elastic collision, the total momentum before and after the collision remains constant. We can express this principle using the equation:
(m1 * v1) + (m2 * v2) = (m1 * u1) + (m2 * u2)
Where m1 and m2 are the masses of the first and second carts, v1 and v2 are their initial velocities, and u1 and u2 are their velocities after the collision.
In this scenario, the initial velocity of the first cart is given as 1.2 m/s, and its velocity after the collision is 1.00 m/s. The mass of the first cart is 200 g, which is equivalent to 0.2 kg.
We can rearrange the equation and solve for the mass of the second cart:
(m1 * v1) + (m2 * v2) = (m1 * u1) + (m2 * u2)
(0.2 * 1.2) + (m2 * 0) = (0.2 * 1.2) + (m2 * 1.00)
0.24 = 0.24 + m2
By subtracting 0.24 from both sides, we find that m2 = 0 kg.
Learn more about velocity here:
https://brainly.com/question/30559316
#SPJ11
A vertical spring (ignore its mass), whose spring stiffness constant is 3n/m is attached to a table and is compressed down 3.2 m. (a) What maximum upward speed can it give to a 0.30−kg ball when released? ( Note you need to find the equilibrium point)(b) How high above its original position (spring compressed) will the ball fly?
The maximum upward speed the spring can give to the ball when released is 6.48 m/s, and the ball will fly approximately 0.331 m above its original position.
(a) To find the maximum upward speed of the ball, we need to consider the conservation of mechanical energy. At the maximum height, the ball will have zero kinetic energy. Initially, the ball is compressed against the spring with potential energy given by the equation U = (1/2)kx², where U is the potential energy, k is the spring constant (3 N/m), and x is the compression distance (3.2 m).
Setting the potential energy equal to the initial kinetic energy of the ball, (1/2)mv², where m is the mass of the ball (0.30 kg) and v is the maximum upward speed we want to find. Therefore, we have (1/2)kx² = (1/2)mv². Rearranging the equation and solving for v, we get v = √((kx²)/m). Substituting the given values, we find v = √((3(3.2)²)/0.30) ≈ 6.48 m/s.
(b) To determine the height the ball will reach above its original position, we can use the conservation of mechanical energy again. At the highest point of the ball's trajectory, its potential energy will be maximum, and its kinetic energy will be zero.
The potential energy at this point is given by mgh, where m is the mass of the ball, g is the acceleration due to gravity (approximately 9.8 m/s²), and h is the maximum height above the original position. Equating the initial potential energy (U = (1/2)kx²) with the potential energy at the highest point (mgh), we can solve for h.
Therefore, (1/2)kx² = mgh. Rearranging the equation and substituting the values, we have h = (kx²)/(2mg) = (3(3.2)²)/(2(0.30)(9.8)) ≈ 0.331 m.
Thus, the ball will reach approximately 0.331 m above its original position.
Learn more about conservation of mechanical energy:
https://brainly.com/question/32426649
#SPJ11
Assume all junction capacitances are equal and each has a capacitance of (1/250 p. If the emitter resistance of transistor i bye by a capacitance C1pf, determine the upper cutoff frequency fy for the amplifier? O A 5.00 GHz OB. 48.00 MHz OC 480.0 kHz VC. OD. 12.50 MHz
Assume all junction capacitances are equal and each has a capacitance of (1/250 p. If the emitter resistance of transistor i bye by a capacitance C1pf, determine the upper cutoff frequency fy for the amplifier? O A 5.00 GHz OB. 48.00 MHz OC 480.0 kHz VC. OD. 12.50 MHz
The upper cutoff frequency fy for the amplifier is 12.50 MHz.
Option D is the correct answer.
Capacitance of each junction = (1/250)p
Capacitance at emitter resistance = C1 = 1p
The upper cutoff frequency of the amplifier is given by the following formula:
fmax = 1/2πRoutC
where,
Rout = output resistance = emitter resistance = R1 = R2 = R3 = ... = Rn
fmax = Upper cutoff frequency
C = junction capacitance
The capacitance at the emitter resistance is in series with the junction capacitance to give a new capacitance.
So the equivalent capacitance = Ceq is given by:
Ceq = C1 + C
The equivalent capacitance is in parallel with all the junction capacitances.
Hence the equivalent capacitance of all the junctions and emitter resistance is given by the following formula:
Ceq = 1/(1/250 n + 1/1)
= (1/250 × 10⁹ + 1) n
= 0.996n
Now we can calculate the upper cutoff frequency using the formula:
fmax = 1/2πRoutCeq
Rout = R1||R2||R3||...||Rn= R/n
i.e.,Rout = R/n = R1/n = R2/n = R3/n = ... = Rn/n
where,R = 2kΩ (given)
Therefore, the upper cutoff frequency is given by the formula:
fmax = 1/2πRoutCeq = 1/2π(R/n)(0.996 n)
= 1/2πR(0.996/n)
= (0.996/2πn) × 10⁶
= 0.996/2π × 10⁶/4
= 12.50 MHz
Hence, the upper cutoff frequency fy for the amplifier is 12.50 MHz.
Option D is the correct answer.
Learn more about the cutoff frequency:
brainly.com/question/30092924
#SPJ11
Engineers and science fiction writers have proposed designing space stations in the shape of a rotating wheel or ring, which would allow astronauts to experience a sort of artificial gravity when walking along the inner wall of the station's outer rim. (a) Imagine one such station with a diameter of 110 m, where the apparent gravity is 2.80 m/s² at the outer rim. How fast is the station rotating in revolutions per minute? ____________ rev/min (b) What If? How fast would the space station have to rotate, in revolutions per minute, for the artificial gravity that is produced to equal that at the surface of the Earth, 9.80 m/s² ? ____________ rev/min
Answer: (a) The speed of the space station in revolutions per minute is 1.47 rev/min.
(b) The space station has to rotate at a speed of 3.52 rev/min
(a) The formula for finding the speed of the space station in revolutions per minute is given by:
v = (gR / 2π)1/2
Where,v = speed of the space station in revolutions per minute (rev/min)g = acceleration due to gravity, R = radius of the space stationπ = 3.14Given that the diameter of the space station is 110 m. So, the radius of the space station, R is given by:R = diameter / 2= 110 / 2= 55 m. And, the apparent gravity at the outer rim, g is 2.80 m/s².Now, substituting the values in the above formula,
v = (gR / 2π)1/2
= [(2.80) × 55 / 2 × 3.14]1/2
= 1.47 rev/min. Therefore, the speed of the space station in revolutions per minute is 1.47 rev/min.
(b) The speed of the space station in revolutions per minute is given by:
v = (gR / 2π)1/2
Where, v = speed of the space station in revolutions per minute (rev/min)g = acceleration due to gravity, R = radius of the space stationπ = 3.14
Here, the artificial gravity that is produced needs to be equal to that at the surface of the Earth, g = 9.80 m/s².
Given that the diameter of the space station is 110 m.
So, the radius of the space station, R is given by: R = diameter / 2= 110 / 2= 55 m.
Now, substituting the values in the above formula, we have:
v = (gR / 2π)1/2
= [(9.80) × 55 / 2 × 3.14]1/2
= 3.52 rev/min.
Therefore, the space station has to rotate at a speed of 3.52 rev/min, for the artificial gravity that is produced to equal that at the surface of the Earth, 9.80 m/s².
Learn more about speed: https://brainly.com/question/13943409
#SPJ11
(a) A 0.552 kg particle has a speed of 2.17 m/s at point A and kinetic energy of 7.64 ) at point B. What is its kinetic energy at A? Submit Answer Tries 0/10 (b) What is its speed at point B? Submit Answer Tries 0/10 (c) What is the total work done on the particle as it moves from A to B?
The total work done on the particle as it moves from A to B is 11.32 J.
(a) A 0.552 kg particle has a speed of 2.17 m/s at point A and kinetic energy of 7.64 J at point B. What is its kinetic energy at A?The kinetic energy of an object is given by the formula KE = (1/2)mv², where m is the mass of the object and v is its velocity.Therefore, at point A,KE = (1/2)mv²= (1/2)(0.552 kg)(2.17 m/s)²= 1.44 J(b) What is its speed at point B?Given that, the particle has kinetic energy of 7.64 J at point B. KE = (1/2)mv², where m is the mass of the object and v is its velocity.Therefore, at point B, 7.64 J = (1/2)(0.552 kg)v²Therefore, v² = (2 x 7.64 J) / (0.552 kg) v² = 27.71
The speed of the object at point B is given by the formula, v = √(27.71) = 5.26 m/s(c) What is the total work done on the particle as it moves from A to B?
The work done on the particle as it moves from A to B is given by the difference in kinetic energy, W = ΔKEKE(B) - KE(A) = (1/2)mv(B)² - (1/2)mv(A)²= (1/2)m(v(B)² - v(A)²) = (1/2)(0.552 kg)(5.26 m/s)² - (1/2)(0.552 kg)(2.17 m/s)²= 11.32 JTherefore, the total work done on the particle as it moves from A to B is 11.32 J.
Learn more about Speed here,
https://brainly.com/question/13943409
#SPJ11
How much energy, in joules, is released when 70.00 {~kg} of hydrogen is converted into helium by nuclear fusion?
Therefore, 5.95 × 10²⁰ J of energy is released when 70.00 kg of hydrogen is converted into helium by nuclear fusion.
The nuclear fusion of 70 kg of hydrogen to helium releases 5.95 × 10²⁰ J of energy. In order to determine how much energy is released when 70.00 kg of hydrogen is converted into helium through nuclear fusion, one can use the equationE=mc².
Here, E is the energy released, m is the mass lost during the fusion reaction, and c is the speed of light squared (9 × 10¹⁶ m²/s²).The amount of mass lost during the reaction can be calculated using the equation:Δm = (m_initial - m_final)Δm = (70 kg - 69.96 kg) = 0.04 kg.
Substituting the values in the first equation:
E = (0.04 kg) × (3 × 10⁸ m/s)²E = 3.6 × 10¹⁷ J, This is the amount of energy released by the fusion of 1 kg of hydrogen.
Therefore, to find the total energy released by the fusion of 70.00 kg of hydrogen, we must multiply the amount of energy released by the fusion of 1 kg of hydrogen by 70.00 kg of hydrogen:E_total = (3.6 × 10¹⁷ J/kg) × (70.00 kg)E_total = 2.5 × 10²⁰ J. Therefore, 5.95 × 10²⁰ J of energy is released when 70.00 kg of hydrogen is converted into helium by nuclear fusion.
Learn more about nuclear fusion
https://brainly.com/question/14019172
#SPJ11