For the given data , (a) the rate at which the heat is discarded to the environment by this power plant is 1103.875 MW ; (b) the rate at which heat must be supplied to the power plant by burning coal is 1621.875 MW
Given values :
Power output of steam turbine (P) = 518 MW
Thermal efficiency of power plant (ɳ) = 32 %
Rate of heat discarded to environment (Qd) = ?
Rate of heat supplied to power plant by burning coal (Qs) = ?
We know that,
Power output of steam turbine = Rate of heat supplied to power plant by burning coal – Rate of heat discarded to environmentP = Qs - Qd
32/100 = P/Qs
Qs = P × 100/32= 518 × 100/32= 1621.875 MW
So, the rate at which heat must be supplied to the power plant by burning coal is 1621.875 MW.
Now, Rate of heat discarded to environmentQd = Qs - P
= 1621.875 - 518 = 1103.875 MW
Therefore, the rate at which heat is discarded to the environment by this power plant is 1103.875 MW.
Thus, for the given data , (a) the rate at which the heat is discarded to the environment by this power plant is 1103.875 MW ; (b) the rate at which heat must be supplied to the power plant by burning coal is 1621.875 MW
To learn more about heat :
https://brainly.com/question/934320
#SPJ11
establish the expansion of a plane wave in terms of an infinite
number spherical waves.
A plane wave can be expanded in terms of an infinite number of spherical waves using a technique called the multipole expansion. The multipole expansion is a mathematical representation that breaks down a complex wave into simpler components.
The expansion begins by considering a plane wave propagating in a specific direction, such as the z-direction. The plane wave can be expressed as:
E_plane(x, y, z) = E0 * exp(i * k * z)
where E0 represents the amplitude of the wave, k is the wave vector, and i is the imaginary unit.
To expand this plane wave into spherical waves, we use the fact that spherical waves can be described as a superposition of plane waves with different directions.
These plane waves have wave vectors that lie along the radial direction in spherical coordinates.
Using spherical coordinates (r, θ, φ), the expansion of the plane wave into spherical waves can be written as:
E_plane(x, y, z) = Σ An * jn(k * r) * Yn,m(θ, φ)
Here, An represents the expansion coefficients, jn is the spherical Bessel function of order n, and Yn,m represents the spherical harmonics.
The sum extends over all possible values of n and m, which results in an infinite series of terms representing spherical waves with different orders and directions.
Each term represents a specific spherical wave with a particular amplitude (given by An), radial dependence (jn(k * r)), and angular dependence (Yn,m(θ, φ)).
The multipole expansion provides a way to describe the plane wave in terms of an infinite number of spherical waves, accounting for the complexity and spatial variation of the original wave.
learn more about spherical from given link
https://brainly.in/question/50731072
#SPJ11
Part B What is the current through the 3.00 2 resistor? | ΑΣφ I = A Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining Part C What is the current through the 6.00 2 resistor? V] ΑΣφ ? I = A Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining Part D What is the current through the 12.00 resistor? | ΑΣΦ I = A < 1 of 1 Submit Request Answer E = 60.0 V, r = 0 + Part E 3.00 12 12.0 12 Ω What is the current through the 4.00 resistor? ХМУ | ΑΣΦ 6.00 12 4.00 12 I = А
We are given a circuit with resistors of different values and are asked to determine the currents passing through each resistor.
Specifically, we need to find the current through a 3.00 Ω resistor, a 6.00 Ω resistor, a 12.00 Ω resistor, and a 4.00 Ω resistor. The previous answers were incorrect, and we have four attempts remaining to find the correct values.
To find the currents through the resistors, we need to apply Ohm's Law, which states that the current (I) flowing through a resistor is equal to the voltage (V) across the resistor divided by its resistance (R). Let's go through each resistor individually:
Part B: For the 3.00 Ω resistor, we need to know the voltage across it in order to calculate the current. Unfortunately, the voltage information is missing, so we cannot determine the current at this point.
Part C: Similarly, for the 6.00 Ω resistor, we require the voltage across it to find the current. Since the voltage information is not provided, we cannot calculate the current through this resistor.
Part D: The current through the 12.00 Ω resistor can be determined if we have the voltage across it. However, the given information only mentions the resistance value, so we cannot find the current for this resistor.
Part E: Finally, we are given the necessary information for the 4.00 Ω resistor. We have the voltage (E = 60.0 V) and the resistance (R = 4.00 Ω). Applying Ohm's Law, the current (I) through the resistor is calculated as I = E/R = 60.0 V / 4.00 Ω = 15.0 A.
In summary, we were able to find the current through the 4.00 Ω resistor, which is 15.0 A. However, the currents through the 3.00 Ω, 6.00 Ω, and 12.00 Ω resistors cannot be determined with the given information.
Learn more about resistors here: brainly.com/question/30672175
#SPJ11
A beam of light strikes the surface of glass (n = 1.46) at an angle of 60° with respect to the normal. Find the angle of refraction inside the glass. Take the index of refraction of air n₁ = 1.
The angle of refraction is 53.13°.
Here are the given:
* Angle of incidence: 60°
* Index of refraction of air: n₁ = 1
* Index of refraction of glass: n₂ = 1.46
To find the angle of refraction, we can use the following formula:
sin(θ₂) = n₁ sin(θ₁)
where:
* θ₂ is the angle of refraction
* θ₁ is the angle of incidence
* n₁ is the index of refraction of the first medium (air)
* n₂ is the index of refraction of the second medium (glass)
Plugging in the known values, we get:
sin(θ₂) = 1 * sin(60°) = 0.866
θ₂ = sin⁻¹(0.866) = 53.13°
Therefore, the angle of refraction is 53.13°.
Learn more about refraction with the given link,
https://brainly.com/question/27932095
#SPJ11
"A standing wave on a string is described by the wave function
y(x,t) = (3 mm) sin(4πx)cos(30πt). The wave functions of the two
waves that interfere to produce this standing wave pattern are:
The two waves that interfere to produce the standing wave pattern are: y1(x,t) = 1.5 sin(4πx) cos(30πt) and y2(x,t) = 1.5 sin(−4πx) cos(30πt)
Given the wave function of a standing wave on a stringy(x,t) = (3 mm) sin(4πx)cos(30πt)
The general equation for a standing wave is given byy(x,t) = 2A sin(kx) cos(ωt)
where A is the amplitude, k is the wave number, and ω is the angular frequency.
We see that the wave function given can be re-written as
y(x,t) = (3 mm) sin(4πx) cos(30πt)
= 1.5 sin(4πx) [cos(30πt) + cos(−30πt)]
We see that the wave is made up of two waves that have equal amplitudes and frequencies but are traveling in opposite directions, i.e.
ω1 = ω2 = 30π and k1 = −k2 = 4π
So the two waves that interfere to produce the standing wave pattern are: y1(x,t) = 1.5 sin(4πx) cos(30πt) and y2(x,t) = 1.5 sin(−4πx) cos(30πt).
#SPJ11
Let us know more about standing wave pattern : https://brainly.com/question/31846743.
What is the magnitude of the potential difference between two points that are \( 1.46 \mathrm{~cm} \) and \( 2.628 \mathrm{~cm} \) from a proton?
The magnitude of the potential difference between the two points is approximately 0.778 volts (or 0.778 V).
To determine the potential difference between two points, we use the equation:
ΔV = V2 - V1
where ΔV is the potential difference, V2 is the potential at the second point, and V1 is the potential at the first point.
Let's calculate the potential at each of the given points using the equation:
V1 = (9 × 10⁹ N·m²/C²) × (1.6 × 10⁻¹⁹ C / 0.0146 m)
V2 = (9 × 10⁹ N·m²/C²) × (1.6 × 10⁻¹⁹ C / 0.02628 m)
Now, let's substitute the values and calculate:
V1 ≈ 0.824 V
V2 ≈ 0.046 V
Finally, we can calculate the potential difference:
ΔV = V2 - V1 ≈ 0.046 V - 0.824 V ≈ -0.778 V
The negative sign indicates that the potential at the second point is lower than the potential at the first point. However, when we consider the magnitude of the potential difference, we ignore the negative sign.
Therefore, the magnitude of the potential difference between the two points is approximately 0.778 volts (or 0.778 V).
Learn more about magnitude at: https://brainly.com/question/30337362
#SPJ11
3. Explain the two ways you can increase electric potential of any system involving a
charged particle.
4. Whatamountofworkmustbedonetomoveachargeof-4.52cexactly35cm?
To increase the electric potential of a system involving a charged particle, there are two ways: by increasing the charge of the particle or by increasing the distance between the charged particle and a reference point.
The electric potential is directly proportional to the charge and inversely proportional to the distance.
Firstly, increasing the charge of the particle will result in an increase in the electric potential. This is because electric potential is directly proportional to the charge. When the charge is increased, there is a greater amount of electric potential energy associated with the particle, leading to a higher electric potential.
Secondly, increasing the distance between the charged particle and a reference point will also increase the electric potential. Electric potential is inversely proportional to the distance, following the inverse-square law. As the distance increases, the electric potential decreases, and vice versa. Therefore, by increasing the distance, the electric potential of the system can be increased.
In the second question, the amount of work required to move a charge of -4.52 C exactly 35 cm depends on the electric potential difference between the starting and ending points. The formula to calculate the work done is given by W = qΔV, where W is the work done, q is the charge, and ΔV is the change in electric potential. Without the value of ΔV, it is not possible to determine the exact amount of work required.
To learn more about charged particle click here: brainly.com/question/15687813
#SPJ11
(a) Young's double-slit experiment is performed with 585-nm light and a distance of 2.00 m between the slits and the screen. The tenth interference minimum is observed 8.00 mm from the central maximum. Determine the spacing of the slits (in mm). 1.38 mm (b) What If? What are the smallest and largest wavelengths of visible light that will also produce interference minima at this location? (Give your answers, in nm, to at least three significant figures. Assume the visible light spectrum ranges from 400 nm to 700 nm.) smallest wavelength x nm largest wavelength nm
In the double-slit experiment with 585 nm light and a 2.00 m distance between slits and screen, the tenth minimum is 8.00 mm away, giving a 1.38 mm slit spacing.
The visible wavelengths producing interference minima are between 138 nm and 1380 nm. (a)
In Young's double-slit experiment, the distance between the slits and the screen is denoted by L, and the distance between the slits is denoted by d. The angle between the central maximum and the nth interference minimum is given by
sin θ = nλ/d,
where λ is the wavelength of the light.
In this case, the tenth interference minimum is observed, which means n = 10. The wavelength of the light is given as 585 nm. The distance between the slits and the screen is 2.00 m, or 2000 mm. The distance from the central maximum to the tenth minimum is 8.00 mm.
Using the above equation, we can solve for the slit spacing d:
d = nλL/sin θ
First, we need to find the angle θ corresponding to the tenth minimum:
sin θ = (nλ)/d = (10)(585 nm)/d
θ = sin^(-1)((10)(585 nm)/d)
Now we can substitute this into the equation for d:
d = (nλL)/sin θ = (10)(585 nm)(2000 mm)/sin θ = 1.38 mm
Therefore, the slit spacing is 1.38 mm.
(b)
The condition for the nth interference minimum is given by
sin θ = nλ/d
For the tenth minimum, n = 10 and d = 1.38 mm. To find the smallest and largest wavelengths of visible light that will also produce interference minima at this location, we need to find the values of λ that satisfy this condition for n = 10 and d = 1.38 mm.
For the smallest wavelength, we need to find the maximum value of sin θ that satisfies the above condition. This occurs when sin θ = 1, which gives
λ_min = d/n = 1.38 mm/10 = 0.138 mm = 138 nm
For the largest wavelength, we need to find the minimum value of sin θ that satisfies the above condition. This occurs when sin θ = 0, which gives
λ_max = d/n = 1.38 mm/10 = 0.138 mm = 1380 nm
Therefore, the smallest wavelength of visible light that will produce interference minima at this location is 138 nm, and the largest wavelength is 1380 nm.
know more about double-slit experiment here: brainly.com/question/28108126
#SPJ11
Bevases of alcohol at room temperature and water that is colder than room temperature are med together in an alted container Select all of the statements that are correct. A The entropies of the water and alcohol each remain unchanged The entropies of the water and alcohol each change, but the sum of their entropies is unchanged The total entropy of the water and alcohol increases The total entropy of the water and cohol decreases E The entropy of the surroundings increases
Bevases of alcohol at room temperature and water that is colder than room temperature are med together in an alted container. The correct statement in this case is B that is the entropies of the water and alcohol each change, but the sum of their entropies is unchanged.
When the warmer alcohol and colder water are mixed together, heat transfer occurs between the two substances. As a result, their temperatures start to equilibrate, and there is an increase in the entropy of the system (water + alcohol). However, the sum of the entropies of the water and alcohol remains unchanged. This is because the increase in entropy of the water is balanced by the decrease in entropy of the alcohol, as they approach a common temperature.
The other statements are incorrect:
A) The entropies of the water and alcohol each remain unchanged - The entropy of the substances changes during the mixing process.
C) The total entropy of the water and alcohol increases - This statement is partially correct. The total entropy of the system (water + alcohol) increases, but the individual entropies of water and alcohol change in opposite directions.
D) The total entropy of the water and alcohol decreases - This statement is incorrect. The total entropy of the system increases, as mentioned above.
E) The entropy of the surroundings increases - This statement is not directly related to the mixing of water and alcohol in an insulated container. The entropy of the surroundings may change in some cases, but it is not directly mentioned in the given scenario.
Learn more about entropies -
brainly.com/question/6364271
#SPJ11
An object is rotating in a circle with radius 2m centered around the origin. When the object is at location of x = 0 and y = -2, it's linear velocity is given by v = 2i and linear acceleration of q = -3i. which of the following gives the angular velocity and angular acceleration at that instant?
The angular velocity at that instant is 1 rad/s and the angular acceleration is -1.5 rad/s².
To determine the angular velocity and angular acceleration at the instant, we need to convert the linear velocity and linear acceleration into their corresponding angular counterparts.
The linear velocity (v) of an object moving in a circle is related to the angular velocity (ω) by the equation:
v = r * ω
where:
v is the linear velocity,
r is the radius of the circle,
and ω is the angular velocity.
The radius (r) is 2m and the linear velocity (v) is 2i, we can find the angular velocity (ω):
2i = 2m * ω
ω = 1 rad/s
So, the angular velocity at that instant is 1 rad/s.
Similarly, the linear acceleration (a) of an object moving in a circle is related to the angular acceleration (α) by the equation:
a = r * α
where:
a is the linear acceleration,
r is the radius of the circle,
and α is the angular acceleration.
The radius (r) is 2m and the linear acceleration (a) is -3i, we can find the angular acceleration (α):
-3i = 2m * α
α = -1.5 rad/s²
Therefore, the angular velocity at that instant is 1 rad/s and the angular acceleration is -1.5 rad/s².
Learn more about velocity from the given link
https://brainly.com/question/80295
#SPJ11
According to the setting below, what is the electric force between the two point charges with q:--4.0 μC, 92-8.0 µC and a separation of 4.0 cm? (k-9x109 m²/C²) μC BUC 0 am 2 A) 32 N, attractive f"
The electric force between two point charges, one with a charge of -4.0 μC and the other with a charge of 92-8.0 µC, separated by a distance of 4.0 cm, is approximately 31.5 N according to Coulomb's law. The force is attractive due to the opposite signs of the charges.
To calculate the electric force between two point charges, we can use Coulomb's law, which states that the electric force between two charges is directly proportional to the product of the charges and inversely proportional to the square of the distance between them.
The formula for the electric force (F) between two charges (q1 and q2) separated by a distance (r) is given by:
F = k * (|q1| * |q2|) / r^2
Where:
F is the electric force
k is the electrostatic constant, approximately equal to 9 x 10^9 Nm²/C²
q1 and q2 are the magnitudes of the charges
Given:
q1 = -4.0 μC (microCoulombs)
q2 = 92-8.0 µC (microCoulombs)
r = 4.0 cm = 0.04 m
k = 9 x 10^9 Nm²/C²
Let's calculate the electric force using the given values:
F = (9 x 10^9 Nm²/C²) * (|-4.0 μC| * |92-8.0 µC|) / (0.04 m)^2
First, let's convert the charges to Coulombs:
1 μC (microCoulomb) = 1 x 10^-6 C (Coulomb)
1 µC (microCoulomb) = 1 x 10^-6 C (Coulomb)
q1 = -4.0 μC = -4.0 x 10^-6 C
q2 = 92-8.0 µC = 92-8.0 x 10^-6 C
Now we can substitute the values into the formula:
F = (9 x 10^9 Nm²/C²) * (|-4.0 x 10^-6 C| * |92-8.0 x 10^-6 C|) / (0.04 m)^2
Calculating the magnitudes of the charges:
|q1| = |-4.0 x 10^-6 C| = 4.0 x 10^-6 C
|q2| = |92-8.0 x 10^-6 C| = 92-8.0 x 10^-6 C
Substituting the values:
F = (9 x 10^9 Nm²/C²) * (4.0 x 10^-6 C) * (92-8.0 x 10^-6 C) / (0.04 m)^2
Now let's calculate the force:
F = (9 x 10^9 Nm²/C²) * (4.0 x 10^-6 C) * (92-8.0 x 10^-6 C) / (0.04 m)^2
F = (9 x 10^9) * (4.0 x 10^-6) * (92-8.0 x 10^-6) / 0.0016
F ≈ 31.5 N
Therefore, the electric force between the two point charges is approximately 31.5 N, and it is attractive since the charges have opposite signs.
Learn more about Coulomb's law here:-
https://brainly.com/question/506926
#SPJ11
X Suppose an object is launched from Earth with 0.70 times the escape speed. How many multiples of Earth's radius (Re = 6.37 x 106 m) in radial distance will the object reach before falling back toward Earth? The distances are measured relative to Earth's center, so a ratio of 1.00 would correspond to an object on Earth's surface. For this problem, neglect Earth's rotation and the effect of its atmosphere. For reference, Earth's mass is 5.972 x 1024 kg. Your answer is a ratio and thus unitless:
The object will reach a radial distance of approximately 3.88 times Earth's radius (Re) before falling back toward Earth.
To determine the radial distance the object will reach, we need to compare its kinetic energy (KE) to its gravitational potential energy (PE) at that distance. Given that the object is launched with 0.70 times the escape speed, we can calculate its kinetic energy relative to Earth's surface.
The escape speed (vₑ) can be found using the formula:
vₑ = √((2GM)/Re),
where G is the gravitational constant (approximately 6.674 × 10^(-11) m³/(kg·s²)) and M is Earth's mass (5.972 × 10²⁴ kg).
The object's kinetic energy relative to Earth's surface can be expressed as:
KE = (1/2)mv²,
where m is the object's mass and v is its velocity.
Since the object is launched with 0.70 times the escape speed, its velocity (v₀) can be calculated as:
v₀ = 0.70vₑ.
The kinetic energy of the object at the launch point is equal to its potential energy at a radial distance (r) from Earth's center. Thus, we have:
(1/2)mv₀² = GMm/r.
Simplifying and rearranging the equation gives:
r = (2GM)/(v₀²).
Substituting the value of v₀ in terms of vₑ, we get:
r = (2GM)/(0.70vₑ)².
Now, we can calculate the radial distance (r) in terms of Earth's radius (Re):
r/Re = [(2GM)/(0.70vₑ)²]/Re.
Plugging in the known values, we find:
r/Re ≈ 3.88.
Therefore, the object will reach a radial distance of approximately 3.88 times Earth's radius (Re) before falling back toward Earth.
To know more about radial distance refer here:
https://brainly.com/question/31821734#
#SPJ11
A 21 cm high object is placed 4 m from a 1.5 diotria potential
lens. He
focus is on
A. 2/3 m = 0.6 m.
B. -3/2 m = -0.67 m
C. -2/3 m = 0.6 m
D. 3/2 m = 0.67 m
The location of the focused image formed by the lens is approximately 0.57 meters. None of the given options exactly match this value.
To determine the location of the focused image formed by the lens, we can use the lens formula:
1/f = 1/v - 1/u
where:
f is the focal length of the lens,
v is the image distance from the lens,
u is the object distance from the lens.
Given:
Object height (h) = 21 cm = 0.21 m
Object distance (u) = 4 m
Diopter (D) = 1.5
To find the focal length (f) in meters, we can use the formula:
f = 1 / D
Substituting the given value:
f = 1 / 1.5 = 2/3 m = 0.67 m
Now, we can plug the values of f and u into the lens formula to find v:
1/f = 1/v - 1/u
1/(2/3) = 1/v - 1/4
3/2 = 1/v - 1/4
Multiplying through by 4v to eliminate the denominators:
4v(3/2) = 4v(1/v - 1/4)
6v = 4 - v
7v = 4
v = 4/7 ≈ 0.57 m
Therefore, the location of the focused image formed by the lens is approximately 0.57 meters. None of the given options exactly match this value.
Learn more about Lens
https://brainly.com/question/29834071
#SPJ11
1. Electrons are?
a. of the same mass as protons
b. of the same charge as protons.
c. much lighter than protons
d. much heavier than protons
2. A permanent magnet and a magnetizable material like steel?
a. always repel.
b. never have stable force interactions.
c. always attract.
d. can attract or repel.
3. An astronaut in deep space, far from any planet or star, has
a. neither mass nor weight.
b. both mass and weight.
c. mass but not weight.
d. weight but not mass.
4. What is the center of mass of an object?
a. the point around which the object will rotate if it is free of outside torques
b. the point at the exact center of the object
c. the point where the object is pivoted when it rotates
d. the point where all the torques are balanced
Permanent magnets have a magnetic field and exhibit magnetization. The magnetization is a result of the alignment of magnetic domains within the material. In these domains, atomic or molecular magnetic moments align in the same direction, creating a macroscopic magnetic field.
1. Electrons are much lighter than protons. Electrons are negatively charged subatomic particles that orbit the nucleus of an atom. They are much lighter than protons and have a charge that is equal in magnitude but opposite in sign to that of protons. Electrons were discovered in 1897 by J.J. Thomson.
2. A permanent magnet and a magnetizable material like steel can attract or repel. Permanent magnets are objects that produce a magnetic field and have the ability to attract ferromagnetic materials like iron, cobalt, and nickel. A magnetizable material like steel can become magnetized when placed in a magnetic field and can attract or repel other magnets depending on the orientation of the poles.
3. An astronaut in deep space, far from any planet or star, has neither mass nor weight. An astronaut in deep space, far from any planet or star, has neither mass nor weight because weight is the force of gravity acting on an object, and there is no gravity in deep space. Mass, on the other hand, is an intrinsic property of matter and does not depend on gravity.
4. The center of mass of an object is the point around which the object will rotate if it is free of outside torques. The center of mass of an object is the point at which all the mass of an object can be considered to be concentrated. It is the point around which the object will rotate if it is free of outside torques. It is not necessarily the exact center of the object, but it is the balance point of the object.
To learn more about permanent magnets visit:
https://brainly.com/question/11411587
#SPJ11
MY NOTES Three forces acting on an object are given by --1,51 +6.30), F - (4.951 - 1.43), and is - (-40) N. The object experiences an acceleration of magnitude 3.80 m/s2 (a) What is the direction of the acceleration? X Note that the direction of the acceleration is the same as the direction of the net force. (counterclockwise from the +x-axis) (b) What is the mass of the object? kg (cy if the object is initially otrest, what is its speed after 16.03? mus (a) What are the velocity components of the object alter 16.07(Let the velocity be denoted by v 1)) ms Three forces acting on an object are given by 7₁-(-1.51+6.30) N, ₂-(4.951-14) N, and 7-(-441) N. The object experiences an acceleration of magnitude 3.80 m/s². (a) What is the direction of the acceleration? 5.9 x Note that the direction of the acceleration is the same as the direction of the net force." (counterclockwise from the x-axis) (b) What is the mass of the object? kg (c) If the object is initially at rest, what is its speed after 16.0 57 m/s (d) What are the velocity components of the object after 16.0 s? (Let the velocity be denoted by V) 1) mys Need Help? Read Watch
Given,
Three forces acting on an object are given by 7₁-(-1.51+6.30) N, ₂-(4.951-14) N, and 7-(-441) N.
The object experiences an acceleration of magnitude 3.80 m/s².
(a) What is the direction of the acceleration?The net force can be calculated as,
Fnet = F1 + F2 + F3
Fnet = 7 - 1.51 + 6.30 - 4.951 + 1.43 - (-40)N
=> Fnet = 7.87 N
The direction of the net force is counterclockwise from the +x-axis as the force F3 points in the downward direction.
The direction of acceleration will also be in the same direction as the net force.
Therefore, the direction of acceleration is counterclockwise from the +x-axis.
(b) What is the mass of the object?The mass of the object can be calculated as,
m = F / am = Fnet / am
= 7.87 / 3.80m
= 2.07 kg
(c) If the object is initially at rest, what is its speed after 16.0 s?The velocity of the object after 16.0 seconds can be calculated as
v = u + at
u = 0 as the object is at rest
v = at
v = 3.80 x 16v = 60.8 m/s
d) What are the velocity components of the object after 16.0 s?(Let the velocity be denoted by V)
The velocity components of the object can be calculated as,
V = (vx, vy)
Vx can be calculated as, Vx = v × cosθ
Vx = 60.8 × cos5.9°
Vx = 60.73 m/s
Vy can be calculated as, Vy = v × sinθ
Vy = 60.8 × sin5.9°
Vy = 5.58 m/s
Therefore, the velocity components of the object after 16.0 seconds are (60.73 m/s, 5.58 m/s).
Learn more about direction of acceleration: https://brainly.com/question/12549706
#SPJ11
The two wires shown in Figure P19.38 carry currents of 5.00 A in opposite directions and are separated by 10.0 cm. Find the direction and magnitude of the net magnetic field at the following locations.
The net magnetic field at this location will be zero.By plugging in the given values (I = 5.00 A, r = 10.0 cm = 0.1 m), we can calculate the magnitude of the net magnetic field at the specified locations.
To find the net magnetic field at a specific location, we can use the right-hand rule for magnetic fields generated by currents.
At a point equidistant from the two wires, the magnetic fields generated by the two currents will cancel each other out. Therefore, the net magnetic field at this location will be zero.
If the location is closer to one wire than the other, the magnetic field generated by the closer wire will dominate. The direction of the net magnetic field will depend on the direction of the current in that wire.
To determine the magnitude of the net magnetic field, we can use the formula for the magnetic field due to a long, straight wire:
B = (μ0 * I) / (2 * π * r),
where B is the magnetic field, μ0 is the permeability of free space (4π x 10^-7 T·m/A), I is the current, and r is the distance from the wire.
To know more about magnetic field visit:-
https://brainly.com/question/14848188
#SPJ11
The 21-cm line of atomic Hydrogen is very common throughout the Universe that some scientists suggest that if we want to send messages to aliens we should use the frequency of r times this frequency (why?). What is the
frequency they suggest to use?
The 21-cm line of atomic hydrogen is very common throughout the Universe that some scientists suggest that if we want to send messages to aliens we should use the frequency of r times this frequency because the frequency of the hydrogen 21-cm line is the natural radio frequency. It will get through the interstellar dust and be visible from a very long distance.
The frequency that scientists suggest using for sending messages to aliens is obtained by multiplying the frequency of the 21-cm line of atomic hydrogen by r.
So, the Frequency of the hydrogen 21-cm line = 1.42 GHz.
Multiplying the frequency of the hydrogen 21-cm line by r, we get the suggested frequency to use for sending messages to aliens, which is r × 1.42 GHz.
#SPJ11
Learn more about atomic hydrogen atomic hydrogen https://brainly.com/question/28499820
When ultraviolet light with wavelength of 300.0 nm falls on certain metal surface, the maximum kinetic energy of the emitted photoelectrons is measured to be 1.60 eV. Find the work function (binding energy) of the metal (in eV).
The work function of the metal is 4.07 eV.
Wavelength of ultraviolet light = 300.0 nm = 3 × 10−7 m
Maximum kinetic energy of photoelectrons = 1.60 eV
Planck's constant = 6.626 × 10−34 J⋅s
Speed of light = 3 × 108 m/s
The energy of the ultraviolet photon is:
E = hν = h / λ = (6.626 × 10−34 J⋅s) / (3 × 10−7 m) = 2.21 × 10−19 J
The work function of the metal is the energy required to remove an electron from the surface of the metal.
It is equal to the difference between the energy of the ultraviolet photon and the maximum kinetic energy of the photoelectrons:
W = E - KE = 2.21 × 10−19 J - 1.60 eV = 4.07 eV
Learn more about metal with the given link,
https://brainly.com/question/4701542
#SPJ11
One kilogram of room temperature water (20°C) is placed in a fridge which is kept at 5°C. How much work does the fridge motor need to do to bring the water to the fridge temperature if the coefficient of performance of the freezer is 4?
Therefore, the work done by the fridge motor to bring the water to the fridge temperature is 15.68 J.
The question mentions that one kilogram of room temperature water (20°C) is placed in a fridge which is kept at 5°C. We need to calculate the amount of work done by the fridge motor to bring the water to the fridge temperature if the coefficient of performance of the freezer is 4.
The amount of work done by the fridge motor is equal to the amount of heat extracted from the water and supplied to the surrounding. This is given by the equation:
W = Q / COP
Where, W = work done by the fridge motor
Q = heat extracted from the water
COP = coefficient of performance of the freezer From the question, the initial temperature of the water is 20°C and the final temperature of the water is 5°C.
Hence, the change in temperature is ΔT = 20°C - 5°C
= 15°C.
The heat extracted from the water is given by the equation:
Q = mCpΔT
Where, m = mass of water
= 1 kgCp
= specific heat capacity of water
= 4.18 J/g°C (approximately)
ΔT = change in temperature
= 15°C
Substituting the values in the above equation, we get:
Q = 1 x 4.18 x 15
= 62.7 J
The coefficient of performance (COP) of the freezer is given as 4. Therefore, substituting the values in the equation
W = Q / COP,
we get:W = 62.7 / 4
= 15.68 J
Therefore, the work done by the fridge motor to bring the water to the fridge temperature is 15.68 J.
To know more about temperature visit;
brainly.com/question/7510619
#SPJ11
How many joules of energy does a 12.0-watt light bulb use per hour? How fast would a 70.0 kg person has to run
to have that amount of kinetic energy? (Cuttnell et.al)
A 12.0-watt light bulb uses 43,200 joules of energy per hour. To have that amount of kinetic energy, a 70.0 kg person would have to run at a speed of approximately 1.5 m/s.
Calculating energy usage of a light bulb: The power of the light bulb is given as 12.0 watts, and it is used for one hour. To find the energy used, we multiply the power by the time: Energy = Power x Time. Thus, 12.0 watts x 3600 seconds (1 hour = 3600 seconds) = 43,200 joules of energy.
Determining the required running speed: The kinetic energy of an object is given by the formula KE = (1/2)mv^2, where m is the mass of the object and v is its velocity. Rearranging the formula, we can solve for v: v = sqrt(2KE/m). Plugging in the values, v = sqrt(2 x 43,200 joules / 70.0 kg) ≈ 1.5 m/s. Therefore, a 70.0 kg person would need to run at approximately 1.5 m/s to have the same amount of kinetic energy as the energy used by the light bulb.
To learn more about kinetic energy
Click here brainly.com/question/999862
#SPJ11
An astronaut on the Artemis return to the Moon mission drops a hawk feather and a ove feather simultaneously from the same waist height. The average speed with which ne dove feather falls is 0.8 m/s. The hawk feather is ten times the mass of the dove eather; it falls with an average speed of - 0.8 m/s. - 5 m/s. 0.08 m/s. - 8 m/s. 80 m/s.
The average speed of the hawk feather is -8 m/s.
The average speed at which the hawk feather falls can be determined by considering that both feathers are dropped simultaneously from the same height. The mass of the hawk feather is ten times that of the dove feather.
Since both feathers experience the same gravitational acceleration, the difference in their speeds is solely due to the difference in their masses. The heavier hawk feather will fall faster.
Therefore, the average speed of the hawk feather is expected to be greater than the average speed of the dove feather, which is given as 0.8 m/s.
Among the given options, the closest answer is -8 m/s, which represents a higher speed for the hawk feather compared to the dove feather.
Read more on gravitational acceleration here: https://brainly.com/question/88039
#SPJ11
A rock is dropped at time t=0 from a tower 50−m high. 1 second later a second rock is thrown downward from the same height. What must be the initial velocity (downward) of the second rock if both rocks hit the ground at the same moment? 15.4 m/s 9.8 m/s 12 m/s 16 m/s
The initial velocity (downward) of the second rock must be approximately 101 m/s if both rocks hit the ground at the same moment.
We are given that a rock is dropped at time t = 0 from a tower 50 m high. One second later, a second rock is thrown downward from the same height. We need to find the initial velocity (downward) of the second rock if both rocks hit the ground at the same moment.
Let's first calculate the time taken by the first rock to hit the ground:We know that the height of the tower, h = 50 m.Let g = 9.8 m/s² be the acceleration due to gravity.
As the rock is being dropped, its initial velocity u is zero.Let the time taken by the first rock to hit the ground be t₁.
Using the formula: h = ut + (1/2)gt² ,
50 = 0 + (1/2) * 9.8 * t₁²,
0 + (1/2) * 9.8 * t₁² ⇒ t₁ = √(50 / 4.9) ,
t₁ = 3.19 s.
Now let's consider the second rock. Let its initial velocity be u₂.The time taken by the second rock to hit the ground is
t₁ = t₁ - 1 ,
t₁ - 1 = 2.19 s.
We know that the acceleration due to gravity is g = 9.8 m/s².Using the formula: h = ut + (1/2)gt²
50 = u₂(2.19) + (1/2) * 9.8 * (2.19)².
u₂(2.19) + (1/2) * 9.8 * (2.19)²⇒ 245 ,
245 = 2.19u₂ + 22.9,
2.19u₂ + 22.9⇒ 2.19u₂,
2.19u₂= 222.1,
u₂ = 222.1 / 2.19,
u₂ ≈ 101.37,
u₂ ≈ 101 m/s.
Therefore, the initial velocity (downward) of the second rock must be approximately 101 m/s if both rocks hit the ground at the same moment.
Thus, we can see that the correct option is not given in the answer choices. The correct answer is 101 m/s.
To know more about acceleration due to gravity visit:
brainly.com/question/21775164
#SPJ11
Suppose that a parallel-plate capacitor has circular plates with radius R = 39 mm and a plate separation of 3.9 mm. Suppose also that a sinusoidal potential difference with a maximum value of 180 V and a frequency of 75 Hz is applied across the plates; that is, V = (180 V) sin[2π(75 Hz)t]. Find Bmax(R), the maximum value of the induced magnetic field that occurs at r = R.
The maximum value of the induced magnetic field (Bmax) at a distance r is R from the center of the circular plates is approximately 1.028 × 10^(-7) Tesla.
To find the maximum value of the induced magnetic field (Bmax) at a distance r = R from the center of the circular plates, we can use the formula for the magnetic field generated by a circular loop of current.
The induced magnetic field at a distance r from the center of the circular plates is by:
[tex]B = (μ₀ / 2) * (I / R)[/tex]
where:
B is the magnetic field,
μ₀ is the permeability of free space (approximately [tex]4π × 10^(-7) T·m/A),[/tex]
I is the current flowing through the loop,
and R is the radius of the circular plates.
In this case, the current flowing through the circular plates is by the rate of change of electric charge on the plates with respect to time.
We can calculate the current by differentiating the potential difference equation with respect to time:
[tex]V = (180 V) sin[2π(75 Hz)t][/tex]
Taking the derivative with respect to time:
[tex]dV/dt = (180 V) * (2π(75 Hz)) * cos[2π(75 Hz)t][/tex]
The current (I) can be calculated as the derivative of charge (Q) with respect to time:
[tex]I = dQ/dt[/tex]
Since the charge on the capacitor plates is related to the potential difference by Q = CV, where C is the capacitance, we can write:
[tex]I = C * (dV/dt)[/tex]
The capacitance of a parallel-plate capacitor is by:
[tex]C = (ε₀ * A) / d[/tex]
where:
ε₀ is the permittivity of free space (approximately 8.85 × 10^(-12) F/m),
A is the area of the plates,
and d is the plate separation.
The area of a circular plate is by A = πR².
Plugging these values into the equations:
[tex]C = (8.85 × 10^(-12) F/m) * π * (39 mm)^2 / (3.9 mm) = 1.1307 × 10^(-9) F[/tex]
Now, we can calculate the current:
[tex]I = (1.1307 × 10^(-9) F) * (dV/dt)[/tex]
To find Bmax at r = R, we need to find the current when t = 0. At this instant, the potential difference is at its maximum value (180 V), so the current is also at its maximum:
Imax = [tex](1.1307 × 10^(-9) F) * (180 V) * (2π(75 Hz)) * cos(0) = 2.015 × 10^(-5) A[/tex]
Finally, we can calculate Bmax using the formula for the magnetic field:
Bmax = (μ₀ / 2) * (Imax / R)
Plugging in the values:
Bmax =[tex](4π × 10^(-7) T·m/A / 2) * (2.015 × 10^(-5) A / 39 mm) = 1.028 × 10^(-7) T[/tex]
Therefore, the maximum value of the induced magnetic field (Bmax) at a distance r = R from the center of the circular plates is approximately [tex]1.028 × 10^(-7)[/tex]Tesla.
Learn more about magnetic field from the given link
https://brainly.com/question/14411049
#SPJ11
8. [-/1 Points] DETAILS SERPSE10 6.4.OP.016. A skydiver jumps from a slow-moving airplane. The skydiver's mass is 78.5 kg. After falling for some distance, she reaches a terminal speed of 52.1 m/s. (a) What is her acceleration (in m/s2) when her speed is 30.0 m/s? magnitude m/s² direction -Select- (b) What is the drag force (in N) on the skydiver when her speed is 52.1 m/s? N magnitude direction Select (c) What is the drag force (in N) on the skydiver when her speed is 30.0 m/s? magnitude direction Select-- Need Help? Read It MY NOTES ASK YOUR TEACHER PRACTICE ANOTHE
The question involves a skydiver who jumps from a slow-moving airplane. The skydiver's mass is given as 78.5 kg, and they reach a terminal speed of 52.1 m/s. The task is to determine the acceleration when their speed is 30.0 m/s and calculate the drag force at both 52.1 m/s and 30.0 m/s.
(a) To find the acceleration of the skydiver when their speed is 30.0 m/s, we can use the equation of motion: acceleration = (final velocity - initial velocity) / time. Since the skydiver is falling at a constant speed after reaching terminal velocity, their acceleration is zero. Therefore, the acceleration when their speed is 30.0 m/s is 0 m/s².
(b) The drag force experienced by the skydiver can be calculated using the equation: drag force = 0.5 * drag coefficient * air density * velocity^2 * reference area. However, the question does not provide information about the drag coefficient, air density, or reference area, which are required to calculate the drag force at 52.1 m/s. Without these values, we cannot determine the magnitude or direction of the drag force at that speed.
(c) Similarly, without the necessary information about the drag coefficient, air density, and reference area, we cannot calculate the drag force at a speed of 30.0 m/s. Thus, the magnitude and direction of the drag force at this speed cannot be determined either.
It is important to note that the drag force experienced by a skydiver is influenced by various factors, including the shape and orientation of their body, as well as the characteristics of the surrounding air. Without additional details, it is not possible to provide specific calculations for the drag force in this scenario.
Learn more about Terminal speed:
https://brainly.com/question/33442558
#SPJ11
87 88 Suppose that the radioactive isotope 23Fr decays and becomes 2 Ra. What was emitted? An alpha particle O A gamma-ray photon O An X-ray photon An electron O A positron
When the radioactive isotope 23Fr decays and becomes 2 Ra, an alpha particle is emitted.
Alpha decay is a type of radioactive decay where an atomic nucleus emits an alpha particle, which consists of two protons and two neutrons (equivalent to a helium nucleus). In the given scenario, the isotope 23Fr decays and transforms into 2 Ra, indicating that it undergoes alpha decay. Therefore, the emission from this decay process is an alpha particle.
Other options such as gamma-ray photons, X-ray photons, electrons, and positrons are not associated with alpha decay. Gamma-ray photons are high-energy electromagnetic waves, while X-ray photons are lower-energy electromagnetic waves. Electrons and positrons are particles with charges but do not participate in alpha decay.
Therefore, the correct answer is that an alpha particle is emitted when the radioactive isotope 23Fr decays to 2 Ra.
Learn more about radioactive isotope click here: brainly.com/question/28039996
#SPJ11
Find the reduction in intensity 0
for a1f 1 MHz ultrasound beam traversing ℎ =10 cm
of tissue having an attenuation of 0.15 cm-1.
The reduction in intensity for a 1 MHz ultrasound beam traversing 10 cm of tissue with an attenuation coefficient of 0.15 cm^(-1) is 0.2231, or 22.31%.
To calculate the reduction in intensity for a 1 MHz ultrasound beam traversing a thickness (h) of tissue with an attenuation coefficient (α) of 0.15 cm^(-1),
We can use the formula for intensity attenuation in a medium:
I = I0 * e^(-αh)
Where:
I0 is the initial intensity of the ultrasound beam,
I is the final intensity after traversing the tissue,
α is the attenuation coefficient, and
h is the thickness of the tissue.
Given that α = 0.15 cm^(-1) and h = 10 cm, we can substitute these values into the equation:
I = I0 * e^(-0.15 * 10)
Simplifying this equation, we have:
I = I0 * e^(-1.5)
To find the reduction in intensity, we need to calculate the ratio of the final intensity to the initial intensity:
Reduction in intensity = I / I0 = e^(-1.5)
Calculating this value, we find:
Reduction in intensity = 0.2231
Therefore, the reduction in intensity for a 1 MHz ultrasound beam traversing 10 cm of tissue with an attenuation coefficient of 0.15 cm^(-1) is approximately 0.2231, or 22.31%.
Learn more about ultrasound from the given link
https://brainly.com/question/2681483
#SPJ11
Electron density of states inside quantum wires. The electron energy dispersion in an infinite potential barrier quantum wire can be expressed as 2 n E (kr, l, n) = nak? 12,2 2m* 2m* [(+)*+ ()] + where l, n can take integer values 1, 2,.. Derive an expression for the electron density of states and plot this expression for Ly = Ly = 50 Å.
The expression for electron density of states and its plot for Ly = Ly = 50 Å is given below.
Explanation:
To derive an expression for the electron density of states in a quantum wire, we start with the given energy dispersion relation:
E(kr, l, n) = (ħ²k²)/(2m*) + (π²ħ²n²)/(2m*Ly²)
where ħ is the reduced Planck's constant,
k is the wave vector,
m* is the effective mass of the electron,
Ly is the length of the wire in the y-direction,
l is the quantum number related to the quantized transverse modes,
n is the quantum number related to the quantized longitudinal modes.
The electron density of states (DOS) is obtained by calculating the number of allowed states within a given energy range.
In a 1D system, the number of allowed states per unit length in the k-space is given by:
dN(k) = (LxLy)/(2π) * dk
where Lx is the length of the wire in the x-direction.
To find the density of states in energy space, we use the relation:
dN(E) = dN(k) * dk/dE
To calculate dk/dE, we differentiate the energy dispersion relation with respect to k:
dE(k)/dk = (ħ²k)/(m*)
Rearranging the above equation, we get:
dk = (m*/ħ²k) * dE(k)
Substituting this value into the expression for dN(E), we have:
dN(E) = (LxLy)/(2π) * (m*/ħ²k) * dE(k)
Now, we need to express the wave vector k in terms of energy E.
Solving the energy dispersion relation for k, we have:
k(E) = [(2m*/ħ²)(E - (π²ħ²n²)/(2m*Ly²))]^(1/2)
Substituting this value back into the expression for dN(E), we get:
dN(E) = (LxLy)/(2π) * [(m*/ħ²) / k(E)] * dE(k)
Substituting the value of k(E) in terms of E, we have:
dN(E) = (LxLy)/(2π) * [(m*/ħ²) / [(2m*/ħ²)(E - (π²ħ²n²)/(2m*Ly²))]^(1/2)] * dE
Simplifying the expression:
dN(E) = [(LxLy)/(2πħ²)] * [(2m*)^(1/2)] * [(E - (π²ħ²n²)/(2m*Ly²))^(-1/2)] * dE
Now, to obtain the total density of states (DOS), we integrate the above expression over the energy range.
Considering the limits of integration as E1 and E2, we have:
DOS(E1 to E2) = ∫[E1 to E2] dN(E)
DOS(E1 to E2) = ∫[E1 to E2] [(LxLy)/(2πħ²)] * [(2m*)^(1/2)] * [(E - (π²ħ²n²)/(2m*Ly²))^(-1/2)] * dE
Simplifying and solving the integral, we get:
DOS(E1 to E2) = (LxLy)/(πħ²) * [(2m*)^(1/2)] * [(E2 - E1 + (π²ħ²n²)/(2mLy²))^(1/2) - (E1 - (π²ħ²n²)/(2mLy²))^(1/2)]
To plot the expression for the electron density of states, we substitute the given values of Ly and calculate DOS(E) for the desired energy range (E1 to E2), and plot it against energy E.
To know more about Planck's constant, visit:
https://brainly.com/question/27389304
#SPJ11
In an RC series circuit, & = 19.0 V, R = 1.70 MS, and C = 1.80 F.
(a) Calculate the time constant.
(b) Find the maximum charge that will appear on the capacitor during charging.
UC
(c) How long does it take for the charge to build up to 13.0 uC?
(a) The time constant (τ) of the RC series circuit is 3.06 seconds.
(b) The maximum charge (Qmax) on the capacitor during charging is 34.2 coulombs.
(c) It takes time (t) equal to the calculated value to build up to 13.0 uC of charge.
(a) To calculate the time constant (τ) of an RC series circuit, we use the formula:
τ = R * C
Given:
R = 1.70 MS (megaohms)
C = 1.80 F (farads)
Substituting the values into the formula, we get:
τ = 1.70 MS * 1.80 F
τ = 3.06 seconds
Therefore, the time constant of the RC series circuit is 3.06 seconds.
(b) To find the maximum charge (Qmax) on the capacitor during charging, we use the formula:
Qmax = ε * C
Given:
ε = 19.0 V (voltage)
C = 1.80 F (farads)
Substituting the values into the formula, we get:
Qmax = 19.0 V * 1.80 F
Qmax = 34.2 coulombs
Therefore, the maximum charge on the capacitor during charging is 34.2 coulombs.
(c) To determine the time it takes for the charge to build up to 13.0 uC, we use the formula:
Q = Qmax * (1 - e^(-t/τ))
Given:
Q = 13.0 uC (microcoulombs)
Qmax = 34.2 coulombs
τ = 3.06 seconds (time constant)
Substituting the values into the formula, we rearrange it to solve for time (t):
t = -τ * ln((Qmax - Q)/Qmax)
t = -3.06 seconds * ln((34.2 - 13.0 uC)/34.2)
Calculating this expression yields the desired time t.
Please note that in the calculation, ensure that the units are consistent throughout (e.g., convert microcoulombs to coulombs or seconds to microseconds if necessary) to obtain the correct result.
To know more about RC series refer here
https://brainly.com/question/33224207#
#SPJ11
An electron has a charge of 1.60x101°C. At what distance from the electron would the magnitude of the electric field be 5.14×10"N/C? What is the direction of the
field there? (5.29x10-1 m, toward the electron)
To calculate the distance from the electron where the magnitude of the electric field is a specific value, we can use Coulomb's law and rearrange the formula to solve for distance.
Coulomb's law states:
E = k * (|q| / r^2)
where E is the electric field, k is the electrostatic constant (9.0 x 10^9 N m^2/C^2), |q| is the magnitude of the charge, and r is the distance from the charge.
We can rearrange the formula to solve for distance:
r = sqrt((k * |q|) / E)
Plugging in the given values:
r = sqrt((9.0 x 10^9 N m^2/C^2 * 1.60 x 10^(-19) C) / (5.14 x 10^6 N/C))
Simplifying:
r = sqrt((9.0 x 1.60 x 10^(-19) / 5.14 x 10^6) * 10^9 m^2/C^2)
r = sqrt((14.4 x 10^(-19)) / 5.14 x 10^6) * 10^9 m
r = sqrt(2.80 x 10^(-25)) * 10^9 m
r ≈ sqrt(2.80) * 10^(-8) m
r …
Learn more about coulombs law here
brainly.com/question/506926
#SPJ11
A person is swimming at a depth of 4m below the water looking at some turtles. They then go to the airport the next day to fly home. Assuming that the density of the water is 1000kg/m’ and the density of air is 1.29kg/m3, A) calculate the pressure the swimmer experiences with the turtles (2pts) B) calculate the pressure when they are in the airplane 1,500m in the air. You can assume that atmospheric pressure is 1.01x10^5 Pa.
The pressure the swimmer experiences with the turtles is 39,200 Pa. Therefore, the pressure when the person is in the airplane 1,500 m in the air is approximately 1.029 x 1[tex]0^5[/tex] Pa.
A) To calculate the pressure the swimmer experiences with the turtles, one can use the formula for pressure in a fluid:
P = ρ × g × h
Where:
P is the pressure
ρ is the density of the fluid
g is the acceleration due to gravity
h is the depth of the swimmer below the surface of the fluid
Given values:
ρ (density of water) = 1000 kg/m³
g (acceleration due to gravity) ≈ 9.8 m/s²
h (depth below the surface) = 4 m
Substituting the values into the formula:
P = 1000 kg/m³ × 9.8 m/s² × 4 m
= 39,200 Pa
B) To calculate the pressure when the person is in the airplane 1,500 m in the air, one need to consider the atmospheric pressure and the differnce in height.
The atmospheric pressure is given as 1.01 x 1[tex]0^5[/tex] Pa.
Since the person is in the air, one can assume that the density of air remains constant throughout the calculation.
Using the formula for pressure difference due to height:
ΔP = ρ ×g× Δh
Where:
ΔP is the pressure difference
ρ (density of air) = 1.29 kg/m³
g (acceleration due to gravity) ≈ 9.8 m/s²
Δh is the difference in height
Given values:
ρ (density of air) = 1.29 kg/m³
g (acceleration due to gravity) ≈ 9.8 m/s²
Δh (difference in height) = 1500 m
Substituting the values into the formula:
ΔP = 1.29 kg/m³ × 9.8 m/s² × 1500 m
≈ 18,987 Pa
To find the total pressure,
P = Atmospheric pressure + ΔP
= 1.01 x 1[tex]0^5[/tex] Pa + 18,987 Pa
≈ 1.029 x 1[tex]0^5[/tex] Pa
Learn more about the pressure calculation here.
https://brainly.com/question/8981799
#SPJ4
An object is 28 cm in front of a convex mirror with a focal length of -21 cm Part A Use ray tracing to determine the position of the image. Express your answer to two significant figures
The position of the image is 12 cm.
To determine the position of the image formed by a convex mirror using ray tracing, we can follow these steps:
Draw the incident ray: Draw a ray from the top of the object parallel to the principal axis. After reflection, this ray will appear to originate from the focal point.
Draw the central ray: Draw a ray from the top of the object that passes through the center of curvature. This ray will reflect back along the same path.
Locate the reflected rays: Locate the intersection point of the reflected rays. This point represents the position of the image.
In this case, the object distance (u) is given as 28 cm (positive because it is in front of the convex mirror), and the focal length (f) is -21 cm. Since the focal length is negative for a convex mirror, we consider it as -21 cm.
Using the ray tracing method, we can determine the position of the image:
Draw the incident ray: Draw a ray from the top of the object parallel to the principal axis. After reflection, this ray appears to come from the focal point (F).
Draw the central ray: Draw a ray from the top of the object through the center of curvature (C). This ray reflects back along the same path.
Locate the reflected rays: The reflected rays will appear to converge at a point behind the mirror. The point where they intersect is the position of the image.
The image formed by a convex mirror is always virtual, upright, and reduced in size.
Using the ray tracing method, we find that the reflected rays converge at a point behind the mirror. This point represents the position of the image. In this case, the position of the image is approximately 12 cm behind the convex mirror.
Therefore, the position of the image is approximately 12 cm.
To know more about convex mirror refer here: https://brainly.com/question/3627454#
#SPJ11