A scuba diver shines a flashlight from beneath the water's surface. The correct answer is b. 65°. Selena uses a converging lens (f=0.12 m) to read a map located 0.08 m from the lens The correct answer is c. +3.0.The correct answer is c. total internal reflection. the minimum angle of incidence is b. 32.46°
1. The correct answer is b. 65°. When light travels from one medium to another, it undergoes refraction. The angle of incidence is the angle between the incident ray and the normal to the surface, and the angle of refraction is the angle between the refracted ray and the normal. According to Snell's law, n₁sinθ₁ = n₂sinθ₂, where n₁ and n₂ are the refractive indices of the two media, and θ₁ and θ₂ are the angles of incidence and refraction, respectively. In this case, the incident medium is water (n = 1.33) and the refracted medium is air (n = 1.00). Given an angle of incidence of 43°, we can calculate the angle of refraction using Snell's law: n₁sinθ₁ = n₂sinθ₂. Plugging in the values, we find sinθ₂ = (n₁ / n₂) * sinθ₁ = (1.33 / 1.00) * sin(43°) ≈ 1.77. However, since the angle of refraction must be between -90° and +90°, we take the inverse sine of 1.77, which gives us approximately 65°.
2. The correct answer is c. +3.0. The magnification of a lens is given by the formula: magnification = - (image distance / object distance). In this case, the object distance (u) is 0.08 m and the focal length (f) of the lens is 0.12 m. Plugging these values into the formula, we get: magnification = - (0.12 / 0.08) = -1.5. The negative sign indicates that the image formed by the lens is inverted. Therefore, the magnification of the lens is +3.0 (positive because the image is upright).
3. The correct answer is c. total internal reflection. Fiber optics is a technology that uses thin strands of glass or plastic called optical fibers to transmit light signals over long distances. The main principle behind fiber optics is total internal reflection. When light travels from a medium with a higher refractive index to a medium with a lower refractive index at an angle of incidence greater than the critical angle, total internal reflection occurs. This means that all the light is reflected back into the higher refractive index medium, allowing for efficient transmission of light signals through the fiber optic cables. Refraction and polarization also play a role in fiber optics, but total internal reflection is the main contribution
4. The correct answer is b. 32.46°. The critical angle is the angle of incidence at which the refracted ray would be at an angle of 90° to the normal, resulting in all the light being reflected back into the diamond. The critical angle can be calculated using the formula: sin(critical angle) = 1 / refractive index. In this case, the refractive index of diamond (n) is 2.419. Plugging this value into the formula, we get sin(critical angle) = 1 / 2.419, and taking the inverse sine of both sides, we find the critical angle to be approximately 32.46°. Therefore, any angle of incidence greater than 32.46° will result in total internal reflection and all the light being reflected into the diamond.
Learn more about refraction here:
https://brainly.com/question/14760207
#SPJ11
A parallel plate capacitor, in which the space between the plates is filled with a dielectric material with dielectric constant k = 10.1, has a capacitor of C= 6.2μF and it is connected to a battery whose voltage is V = 5.9V and fully charged. Once it is fully charged, it is disconnected from the battery and without affecting the charge on the plates, dielectric material is removed from the capacitor. How much change occurs in the energy of the capacitor (final energy minus initial energy)? Express your answer in units of mJ (mili joules) using two decimal places
The change in energy of the capacitor (final energy minus initial energy) is 2.11 mJ.
When the dielectric material is removed from the capacitor, the capacitance decreases, and the voltage across the plates increases to keep the charge constant. Let's calculate the initial energy stored in the capacitor as well as the final energy stored in the capacitor.Energy stored by a capacitor is given by:U = 1/2 CV²Initial energy,U1 = 1/2 × 6.2 × (5.9)² U1 = 102.43 mJWhen the dielectric material is removed from the capacitor, the capacitance changes.
Capacitance without the dielectric material,C2 = C / k C2 = 6.2 μF / 10.1 C2 = 0.613 μFThe voltage across the plates increases.V2 = V × k V2 = 5.9 V × 10.1 V2 = 59.59 VFinal energy,U2 = 1/2 × 0.613 × (59.59)² U2 = 104.54 mJChange in energy,ΔU = U2 - U1 ΔU = 104.54 - 102.43 ΔU = 2.11 mJTherefore, the change in energy of the capacitor (final energy minus initial energy) is 2.11 mJ.
Learn more about Energy here,
https://brainly.com/question/2003548
#SPJ11
In this scenario, there is a uniform electric and magnetic field in a xy system. A small particle with mass=8.5e-3kg and q=-8.5microC moves in the positive direction at a velocity v= 7.2e6 m/s. E field is given E=5.3e3 j N/C and B field is 8.1e-3 i T. As the particle enters the fields, please calculate acceleration in m/s² in the hundredth place.
The acceleration experienced by the particle is in a uniform electric and magnetic field is 587.30 m/s².
Mass of the particle, m = 8.5 × 10⁻³ kg
Charge on the particle, q = - 8.5 µC
Velocity of the particle, v = 7.2 × 10⁶ m/s
Electric field, E = 5.3 × 10³ N/C
And magnetic field, B = 8.1 × 10⁻³ T
Now, the force experienced by the particle due to electric field,
E = F/Q or F = QE... (1)
Where, F is the force experienced by the particle due to electric field, Q is the charge on the particle, and E is the electric field.
As the particle has a charge of -8.5 µC, so substituting all the given values in equation (1),
F = -8.5 × 10⁻⁶ × 5.3 × 10³= - 45.05 × 10⁻³ N = - 45.05 mN
Now, the force experienced by the particle due to magnetic field,
F = BQv... (2)
Where, F is the force experienced by the particle due to magnetic field, B is the magnetic field, Q is the charge on the particle, and v is the velocity of the particle.
Substituting all the given values in equation (2),
F = 8.1 × 10⁻³ × 8.5 × 10⁻⁶ × 7.2 × 10⁶F = 4.986 N
Now, the acceleration experienced by the particle,
a = F/m... (3)
Where, a is the acceleration experienced by the particle, F is the net force acting on the particle, and m is the mass of the particle.
Substituting all the above values in equation (3), we get
a = 4.986/8.5 × 10⁻³a = 587.29 m/s² ≈ 587.30 m/s²
Therefore, the acceleration experienced by the particle is 587.30 m/s².
Learn more about electric and magnetic field https://brainly.com/question/1594186
#SPJ11
A 100-W light bulb radiates energy at a rate of 115 J/s, (The watt is defined as 1l/s. If all the light is emitted has a wavelength of 545 nm, how many photons are emitted per a second? Explanation:
The number of photons emitted per second is 3.63 × 10⁻²¹ photons/s.
The number of photons emitted per second when a 100-W light bulb radiates energy at a rate of 115 J/s with all the light emitted having a wavelength of 545 nm can be calculated as follows:
Firstly, we will calculate the energy per photon:E = hc/λwhere, E = Energy of a photonh = Planck's constant = 6.626 × 10⁻³⁴ Js (joule-second)λ = wavelength of light = 545 nm = 545 × 10⁻⁹ m (meter)c = speed of light = 3 × 10⁸ m/sE = (6.626 × 10⁻³⁴ J s)(3 × 10⁸ m/s)/(545 × 10⁻⁹ m)= 3.63 × 10⁻¹⁹ JE = 3.63 × 10⁻¹⁹ J.
Now, we can calculate the number of photons per second emitted by the light bulb:Power of light = Energy per second/Number of photons per secondP = E/tN = E/PWhere, P = Power of light = 100 W = 100 J/st = Time = 1sE = Energy per photon = 3.63 × 10⁻¹⁹ JN = Number of photons per second= E/P= (3.63 × 10⁻¹⁹ J)/(100 J/s)= 3.63 × 10⁻²¹/s.
Therefore, the number of photons emitted per second is 3.63 × 10⁻²¹ photons/s.
Learn more about photons here,
https://brainly.com/question/31379966
#SPJ11
shows a circuit with an area of 0.070 m 2
containing a R=1.0Ω resistor and a C=210μF uncharged capacitor. Pointing into the plane of the circuit is a uniform magnetic field of magnitude 0.20 T. In 1.0×10 −2
s the magnetic field strengthens at a constant rate to become 0.80 T pointing into the plane. Figure 1 of 1 Part A What maximum charge (sign and magnitude) accumulates on the upper plate of the capacitor in the diagram? Express your answer to two significant figures and include appropriate units. A 4.00μF and an 9.00μF capacitor are connected in parallel to a 65.0 Hz generator operating with an rms voltage of 120 V. Part A What is the rms current supplied by the generator?
The maximum charge on the upper plate of the capacitor in the circuit is approximately 8.82 × 10^(-5) C (coulombs).
To determine the maximum charge on the upper plate of the capacitor, we need to calculate the change in magnetic flux through the circuit. The change in magnetic flux induces an electromotive force (emf) in the circuit, which causes the accumulation of charge on the capacitor plates.
The maximum charge on the capacitor can be calculated using Faraday's law of electromagnetic induction:
[tex]\[ \Delta \Phi = -\frac{{d\Phi}}{{dt}} \][/tex]
where ΔΦ is the change in magnetic flux, and dt is the change in time.
The change in magnetic flux can be calculated by multiplying the change in magnetic field (ΔB) by the area of the circuit (A). In this case, ΔB = 0.80 T - 0.20 T = 0.60 T.
[tex]\[ \Delta \Phi = \Delta B \cdot A \][/tex]
Substituting the values, we find:
[tex]\[ \Delta \Phi = 0.60 \, \text{T} \cdot 0.070 \, \text{m}^2 \][/tex]
Next, we need to calculate the charge accumulated on the capacitor plates. The charge (Q) is related to the change in magnetic flux by the equation:
[tex]\[ Q = C \cdot \Delta \Phi \][/tex]
where C is the capacitance of the capacitor.
Substituting the given capacitance value (C = 210 μF = 210 × 10^(-6) F) and the calculated change in magnetic flux, we can find the maximum charge on the upper plate of the capacitor.
[tex]\[ Q = (210 * 10^{-6} \, \text{F}) \cdot (0.60 \, \text{T} \cdot 0.070 \, \text{m}^2) \][/tex]
Calculating this expression will give us the maximum charge on the upper plate of the capacitor.
Learn more about magnetic flux here:
https://brainly.com/question/1596988
#SPJ11
Consider the following figure. (a) A conducting laop in the shape of a square of edge length t=0.420 m carries a current t=9.60 A as in the figure above. Calculate the magnitude and direction of the magnetie field at the center of the square. mognitude गT direction (b) If this conductor in reshaped to form a cicular loop and carries the same current, what is the value of the magnetic field at the center? magnitude HT direction Meed Hatp?
The direction of magnetic field is vertical upwards.
(a) Calculation of magnitude and direction of magnetic field at the center of a square shaped conducting loop:
The magnetic field can be calculated by using Ampere's Law for a closed path around the current carrying wire which is given by;∮ B·dl=μ₀I,where B is the magnetic field strength, dl is the differential length element, I is the current, and μ₀ is the permeability of free space. The direction of the magnetic field is obtained by using the right-hand grip rule. A square shaped conducting loop of edge length t=0.420 m and carrying current I=9.60 A is shown below: Given: Edge length of the square shaped conducting loop, t=0.420 m Current, I=9.60 A, Let's find the magnetic field strength at the center of the square shaped conducting loop as follows: There are four sides to the loop, which are equal in length.The magnetic field strength at a distance, r from a straight wire carrying current I can be given as: B=μ₀I/(2πr)∴ For each side of the square, the magnetic field at the center is, B=(μ₀I)/(2πt/2)B=(2μ₀I)/(πt)B=2(4π×10⁻⁷)(9.60)/(π×0.420)B=4.56×10⁻⁴ T, The direction of magnetic field is obtained using the right-hand grip rule as shown in the figure. Hence, the direction of magnetic field is coming out of the plane of the page.(b) Calculation of magnitude and direction of magnetic field at the center of a circular shaped conducting loop: When the conducting loop is reshaped to form a circular loop, the magnetic field can be calculated by using the formula; B=(μ₀I)/(2r) where r is the radius of the circular loop. Given: Current, I=9.60 A.
The radius of the circular loop can be obtained as t/2=0.420/2=0.210 m. Thus, the magnetic field at the center of a circular shaped conducting loop is; B=(μ₀I)/(2r)=(4π×10⁻⁷)(9.60)/(2×0.210)B=0.091 T. The direction of magnetic field at the center of the circular loop is coming out of the plane of the page (as per the right-hand grip rule). Hence, the direction of magnetic field is vertical upwards.
To know more about perpendicular visit:
https://brainly.com/question/14988741
#SPJ11
A small drop of water is suspended motionless in air by a uniform electric field that is directed upward and has a magnitude of 7590 N/C. The mass of the water drop is 5.22 x 10 kg. How many excess electrons or protons reside on the drop?
A small water drop suspended in air by an upward-directed electric field of 7590 N/C can be analyzed to determine the number of excess electron or protons residing on the drop's surface.
The electric force on a charged object in an electric field: F = qE,
In this case, the electric force on the water drop is balanced by the gravitational force, so we have: mg = qE,
Rearranging the equation, we can solve for the charge q: q = mg/E.
q = (5.22 x 10^(-10) kg)(9.8 m/s²) / 7590 N/C.
Calculating this expression, we find the charge q to be approximately 6.86 x 10^(-14) C.
Since the elementary charge is e = 1.6 x 10^(-19) C.
Number of excess electron or protons = q / e = (6.86 x 10^(-14) C) / (1.6 x 10^(-19) C).
Evaluating this expression, we find that approximately 4.29 x 10^5 excess electrons or protons reside on the water drop.
Learn more about electron here;
https://brainly.com/question/860094
#SPJ11
A sled with mass m experiences a total force of strength F, resulting in an acceleration a. Find F (in N), if m = 6.3 kg and a = 18.0 m/s.
When a sled with a mass of 6.3 kg experiences an acceleration of 18.0 m/s, the total force exerted on it is calculated to be 113.4 N using Newton's second law of motion.
According to Newton's second law of motion, the force F exerted on an object is equal to the product of its mass and acceleration. Mathematically, this can be represented as F = m * a, where F is the force, m is the mass, and a is the acceleration.
Given that the mass of the sled is 6.3 kg and the acceleration is 18.0 m/s, we can substitute these values into the equation. Multiplying the mass and acceleration together, we have F = 6.3 kg * 18.0 m/s.
Calculating the product, we find that F = 113.4 N. Therefore, the force exerted on the sled is 113.4 Newtons.
Learn more about acceleration here:
https://brainly.com/question/2303856
#SPJ11
Problem/Question: Megan and Jade are two of Saturn's satellites. The distance from Megan to the center of Saturn is approximately 4.0 times farther than the distance from Jade to the center of Saturn. How does Megan's orbital period, TM, compare to that of Jade, TJ?
Potential Answer: *Would this just be "4TJ"?*
Megan's orbital period (TM) is four times longer than that of Jade (TJ).
The orbital period of a satellite is the time it takes for the satellite to complete one full orbit around its primary body. In this scenario, Megan and Jade are two of Saturn's satellites, and the distance from Megan to the center of Saturn is approximately 4.0 times greater than the distance from Jade to the center of Saturn.
According to Kepler's Third Law of Planetary Motion, the orbital period of a satellite is directly proportional to the cube root of its average distance from the center of the primary body. Since Megan's distance from Saturn is 4.0 times greater than Jade's distance, the cube root of the distances ratio would be 4.0^(1/3) = 1.587.
Therefore, Megan's orbital period (TM) would be approximately 4 times longer than that of Jade (TJ), or TM = 4TJ. This implies that Megan takes four times as long as Jade to complete one orbit around Saturn.
Learn more about orbital period here:
https://brainly.com/question/3077562
#SPJ11
K=2,C=1) Describe, in your own words, how you would determine the acceleration of an object from a Velocity-time graph.
The acceleration of an object can be determined from a Velocity-time graph by analyzing the slope of the graph, either by calculating the average acceleration between two points or by determining the instantaneous acceleration at a specific point on the graph.
To determine the acceleration of an object from a Velocity-time graph, you would need to look at the slope or the steepness of the graph at a particular point.
Acceleration is defined as the rate of change of velocity over time. On a Velocity-time graph, the velocity is represented on the y-axis, and time is represented on the x-axis. The slope of the graph represents the change in velocity divided by the change in time, which is essentially the definition of acceleration.
If the slope of the graph is a straight line, the acceleration is constant. In this case, you can calculate the acceleration by dividing the change in velocity by the change in time between two points on the graph.
If the graph is curved, the acceleration is not constant but changing. In this case, you would need to calculate the instantaneous acceleration at a specific point. To do this, you can draw a tangent line to the curve at that point and determine the slope of that tangent line. The slope of the tangent line represents the instantaneous acceleration at that particular moment.
Learn more about Velocity-time graph here:
https://brainly.com/question/32254104
#SPJ11
QUSTION 2 Describe the following on Optical wave guides; a) The theory of operation, structure and characteristics b) Modes of operation c) Application [10marks] [5marks] [5marks]
Optical Wave Guides are fibers or cables used to transmit light. The light waves travel through the core while the cladding reflects the waves back to the core, thereby reducing attenuation. The following are the descriptions of optical waveguides:
a) The theory of operation, structure and characteristics, Theory of operation: In optical waveguides, the light is guided along the length of the cable with the help of reflection. Structure: The basic structure of an optical waveguide consists of a core that is surrounded by a cladding. The core has a higher refractive index compared to the cladding. Characteristics: Optical waveguides have low attenuation, high bandwidth, and they are immune to electromagnetic interference.
b) Modes of operation: The modes of operation for optical waveguides include single-mode and multimode. The single-mode is for low attenuation and it can support only one mode of light propagation while the multimode can support multiple modes of light propagation.
c) Application: Optical waveguides are used in a variety of applications such as telecommunications, medical equipment, military equipment, and industrial applications. They are used for data transmission and imaging applications. They are also used in laser systems, medical instruments such as endoscopes, and fiber optic sensors for environmental monitoring.
let's learn more about Optical Wave Guides:
https://brainly.com/question/32646762
#SPJ11
A 230 V DC shunt motor has an armature current of 3 33 A at the rated voltage and at a no-load speed of 1000 rpm The field and armature resistance are 160 and 0 3 0 respectively The supply current at full load and rated voltage is 40 A Draw the equivalent circuit of the motor with the power supply Calculate the full load speed if armature reaction weakens the no load flux by 6% 31 Equivalent circuit with variables and values (4) 32 No load emf (4) 33 Full load emf (2) 34 Full load speed (3)
The No load is given as 220V
The full load is 218V
The full-load speed of the motor is therefore approximately 1060rpm.
How to solve for the loads32) No load emf:
The armature current at no-load is 33A. Therefore, we can calculate the no-load emf using the formula provided above:
= 230V - 33A * 0.30Ω
= 220V
33) Full load emf:
The supply current at full load is 40A.:
= 230V - 40A * 0.30Ω
= 218V
34) Full load speed:
The speed ratio is increased by 6%.
Speed ratio = 220V / 218V * 1.06
= 1.06
Full load speed = 1000rpm * 1.06
= 1060rpm
The full-load speed of the motor is therefore approximately 1060rpm.
Read more on full load here https://brainly.com/question/26064065
#SPJ4
Specify the coordinate system (Cartesian, cylindrical, spherical) you would use, along with any relevant assumptions, when modeling transport processes in each of the following scenarios: a. Energy loss through a flat double-pane window b. Produced fluid motion when coffee is stirred in a typical mug c. evaporation of beads of water from waterproof surfaces d. The transfer of dissolved oxygen from a culture medium into sphere-shaped cells e. Energy dissipation from the skin of a tall and skinny human f. Water evaporation of beads of water from waterproof surfaces g. heating of a cold bottle of alcoholic cider by a warm hand
a. Cartesian coordinate system would be appropriate to model energy loss through a flat double-pane window.
b. Cartesian coordinate system can be used to model the produced fluid motion when coffee is stirred in a typical mug.
c. Cartesian coordinate system would be suitable to model the evaporation of beads of water from waterproof surfaces.
d. Spherical coordinate system is appropriate to model the transfer of dissolved oxygen from a culture medium into sphere-shaped cells.
e. Cylindrical coordinate system would be suitable to model energy dissipation from the skin of a tall and skinny human.
f. Cartesian coordinate system can be used to model water evaporation of beads of water from waterproof surfaces.
g. Cartesian coordinate system would be appropriate to model the heating of a cold bottle of alcoholic cider by a warm hand.
a. For energy loss through a flat double-pane window, the Cartesian coordinate system is appropriate as it allows modeling in a 2D plane, where the window can be represented by a rectangular shape with x and y coordinates.
b. The produced fluid motion when coffee is stirred in a typical mug can also be modeled using the Cartesian coordinate system, as it allows capturing the 2D motion of the fluid within the mug.
c. The evaporation of beads of water from waterproof surfaces can be modeled using the Cartesian coordinate system, where the surface can be represented by a 2D plane, and the evaporation process can be analyzed in that plane.
d. The transfer of dissolved oxygen from a culture medium into sphere-shaped cells can be modeled using the spherical coordinate system, as it allows capturing the radial distance and angles associated with the transfer process.
e. Energy dissipation from the skin of a tall and skinny human can be modeled using the cylindrical coordinate system, as it allows analyzing the heat transfer in a cylindrical-shaped body, considering radial and height coordinates.
f. Water evaporation of beads of water from waterproof surfaces can be modeled using the Cartesian coordinate system, similar to scenario c, where the evaporation process is analyzed on a 2D plane.
g. The heating of a cold bottle of alcoholic cider by a warm hand can be modeled using the Cartesian coordinate system, as it allows analyzing the heat transfer in a 3D space, considering x, y, and z coordinates.
To know more about the Cartesian coordinate system click here:
https://brainly.com/question/4726772
#SPJ11
A solenoid 3.36E-2m in diameter and 0.317m long has 348 turns and carries 12.0A.
a) Calculate the flux through the surface of a disk of radius 5.00E-2m that is positioned perpendicular to and centred on the axis of the solenoid.
b) Figure b) shows an enlarged end view of the same solenoid as in the last question. Calculate the flux through the blue area, which is defined by an annulus that has an inner radius of 0.366cm and an outer radius of 0.732cm.
a) The flux through the surface of the disk is 0.0364 T·m².
b) The flux through the blue area is 0.121 T·m².
a) To calculate the flux through the surface of the disk, we can use the formula for the magnetic field inside a solenoid: B = μ₀nI, where B is the magnetic field, μ₀ is the permeability of free space (4π × 10⁻⁷ T·m/A), n is the number of turns per unit length, and I is the current. The magnetic field inside the solenoid is uniform, and since the disk is positioned perpendicular to the axis of the solenoid, the magnetic field passing through it is also uniform.
The magnetic flux (Φ) through the surface of the disk is given by Φ = BA, where A is the area of the disk. The area of the disk can be calculated using the formula A = πr², where r is the radius of the disk. Substituting the given values into the equations, we get B = (4π × 10⁻⁷ T·m/A) × (348 turns/0.317 m) × (12.0 A) ≈ 0.436 T. The area of the disk is A = π(5.00 × 10⁻² m)² ≈ 0.7854 × 10⁻³ m². Finally, the flux is Φ = (0.436 T) × (0.7854 × 10⁻³ m²) ≈ 0.0364 T·m².
b) To calculate the flux through the blue area, we need to find the magnetic field passing through the annulus defined by the inner and outer radii. Since the solenoid is perpendicular to the plane of the annulus, the magnetic field passing through it is uniform. The flux through the annulus is given by Φ = BA, where B is the magnetic field and A is the area of the annulus. The area of the annulus can be calculated using the formula A = π(r_outer² - r_inner²), where r_outer and r_inner are the outer and inner radii, respectively.
The magnetic field B is the same as calculated in part a). Substituting the given values, we have B ≈ 0.436 T, r_outer = 0.732 cm = 0.00732 m, and r_inner = 0.366 cm = 0.00366 m. The area of the annulus is A = π((0.00732 m)² - (0.00366 m)²) ≈ 0.121 m². Therefore, the flux through the blue area is Φ = (0.436 T) × (0.121 m²) ≈ 0.121 T·m².
Learn more about magnetic field here:
https://brainly.com/question/19542022
#SPJ11
A 110g mass on a spring oscillates on a frictionless horizontal surface with a period of 0.60s and an amplitude of 18.0cm. Determine the:
a) Spring constant
b) Maximum spring potential energy of the system
c) Maximum speed of the mass
a)The spring constant of the system is 12.16 N/m. b).The maximum potential energy stored in the spring is 0.198 J. c)The maximum speed of the mass is 1.89 m/s.
a) Spring Constant k is given by the formula;k= 4π²m/T²where;T is the time periodm is the massk is the spring constantSubstitute the given values;m = 110g = 0.110kgT = 0.60 sTherefore;k = (4 x 3.14² x 0.110)/(0.60)² = 12.16 N/mTherefore, the spring constant of the system is 12.16 N/m.
b) Maximum spring potential energy of the systemThe maximum potential energy stored in the spring during its oscillations is given by the formula;U = (1/2) kx²where; x is the amplitude of the oscillationSubstitute the given values;k = 12.16 N/mx = 18.0 cm = 0.18 mTherefore;U = (1/2) x k x² = 0.5 x 12.16 x (0.18)² = 0.198 JTherefore, the maximum potential energy stored in the spring is 0.198 J.
c) Maximum speed of the massThe maximum speed of the mass can be obtained using the formula;vmax= Aωwhere;A is the amplitude ω is the angular velocity.Substitute the given values;A = 18.0 cm = 0.18 mω = 2π/T = 2 x 3.14/0.60Therefore;vmax = Aω = 0.18 x 2 x 3.14/0.60vmax = 1.89 m/sTherefore, the maximum speed of the mass is 1.89 m/s.
Learn more about amplitude here,
https://brainly.com/question/3613222
#SPJ11
A force sensor was designed using a cantilever load cell and four active strain gauges. Show that the bridge output voltage (eo1) when the strain gauges are connected in a full bridge configuration will be four times greater than the bridge output voltage (eo2) when connected in a quarter bridge configuration (Assumptions can be made as required)
To understand why the bridge output voltage (eo1) is four times greater than the bridge output voltage (eo2) when the strain gauges are connected in a full bridge configuration compared to a quarter bridge configuration, let's examine the working principles of both configurations.
1. Full Bridge Configuration:
In a full bridge configuration, all four strain gauges are active and connected to form a Wheatstone bridge. The bridge is typically composed of two pairs of strain gauges, with each pair being connected to opposite arms of the bridge. When a force is applied to the cantilever load cell, it causes strain on the strain gauges, resulting in a change in their resistance. This change in resistance leads to an imbalance in the bridge circuit, and an output voltage, eo1, is generated across the bridge terminals.
2. Quarter Bridge Configuration:
In a quarter bridge configuration, only one of the four strain gauges is active and connected to the bridge. The other three strain gauges are inactive and serve as dummy or compensation elements. The active strain gauge experiences a change in resistance due to the applied force, resulting in an output voltage, eo2, across the bridge terminals.
Now, let's compare the output voltages of both configurations:
In the full bridge configuration:
eo1 = ΔR/R * V_excitation
In the quarter bridge configuration:
eo2 = ΔR/R * V_excitation
The ΔR/R term represents the fractional change in resistance of the strain gauge due to the applied force. Since the strain gauges in both configurations experience the same strain due to the same applied force, the ΔR/R term is identical.
However, in the full bridge configuration, the bridge circuit includes all four strain gauges, while in the quarter bridge configuration, it includes only one strain gauge. As a result, the full bridge configuration offers a larger overall change in resistance compared to the quarter bridge configuration.
Since the output voltage is directly proportional to the change in resistance, we can conclude that eo1 will be four times greater than eo2 in a full bridge configuration compared to a quarter bridge configuration.
Therefore, the bridge output voltage (eo1) will be four times greater than the bridge output voltage (eo2) when the strain gauges are connected in a full bridge configuration compared to a quarter bridge configuration.
To learn more about Bridge configuration, visit:
https://brainly.com/question/31756326
#SPJ11
A pulley has an IMA of 13 and an AMA of 6. If the input of the pulley is pulled 13.9 m, how far will the output move?
______ m If the input of the pulley is pulled with a force of 2300 N, how much force will act at the output end of the pulley? ______N Calculate the % efficiency of the pulley.
If the input of the pulley is pulled with a force of 2300 N, the force will act at the output end of the pulley is 180.7 m .
The force acting at the output end of the pulley is 13800 N.
The % efficiency of the pulley is approximately 46.15%.
To solve this problem, we can use the formulas for the Ideal Mechanical Advantage (IMA), Actual Mechanical Advantage (AMA), and efficiency of a pulley system.
Given:
IMA = 13
AMA = 6
Input distance = 13.9 m
Input force = 2300 N
(a) To find the output distance, we can use the formula:
IMA = Output distance / Input distance
Rearranging the formula, we get:
Output distance = IMA * Input distance
Substituting the given values, we have:
Output distance = 13 * 13.9 = 180.7 m
Therefore, the output will move 180.7 m.
(b) To find the force at the output end, we can use the formula:
AMA = Output force / Input force
Rearranging the formula, we get:
Output force = AMA * Input force
Substituting the given values, we have:
Output force = 6 * 2300 = 13800 N
Therefore, the force acting at the output end of the pulley is 13800 N.
(c) To calculate the efficiency of the pulley, we can use the formula:
Efficiency = (AMA / IMA) * 100%
Substituting the given values, we have:
Efficiency = (6 / 13) * 100% ≈ 46.15%
Therefore, the % efficiency of the pulley is approximately 46.15%.
TO know more about Ideal Mechanical Advantage (IMA)
https://brainly.com/question/17457168
#SPJ11
A copper wire of length 10 ft, with a cross sectional area of 1.0 mm², and a Young’s modulus 10x10¹⁰ N/m² has a weight load hung on it. If its increase in length is 1/8 of inch, what is the value of the weight approximately? a. 200 kg b. 400 kg c. 600 kg d. 800 kg e. 1000 kg
A copper wire of length 10 ft, with a cross sectional area of 1.0 mm², and a Young’s modulus 10x10¹⁰ N/m² has a weight load hung on it. If its increase in length is 1/8 of inch, the value of the weight is approximately:
d. 800 kg.
To calculate the approximate value of the weight hung on the copper wire, we can use Hooke's Law, which states that the elongation of a material is directly proportional to the applied force.
Hooke's Law formula: F = k * ΔL
Where:
F = Force (weight)
k = Spring constant (Young's modulus)
ΔL = Change in length
Given:
Length of wire (L) = 10 ft = 120 inches
Cross-sectional area (A) = 1.0 mm² = 1.0 × 10⁻⁶ m²
Young's modulus (Y) = 10 × 10¹⁰ N/m²
Change in length (ΔL) = 1/8 inch = 1/8 × 1/12 = 1/96 feet
To find the spring constant (k), we can use the formula:
k = (Y * A) / L
k = (10 × 10¹⁰ N/m²) * (1.0 × 10⁻⁶ m²) / (120 inches)
Now, let's calculate the value of k:
k = (10 × 10¹⁰ N/m²) * (1.0 × 10⁻⁶ m²) / (120 inches)
= 8.33 × 10⁻⁶ N/inch
Now, we can substitute the values into Hooke's Law formula to find the approximate weight:
F = (8.33 × 10⁻⁶ N/inch) * (1/96 feet)
F = 8.33 × 10⁻⁶ N/inch * 96 inches/1 foot
= 8.33 × 10⁻⁶ N/inch * 96
= 0.799 N
To convert the force from Newtons to kilograms, we can divide it by the acceleration due to gravity (g ≈ 9.8 m/s²):
Weight (W) = F / g
W = 0.799 N / 9.8 m/s²
W ≈ 800 kg
Approximately, the value of the weight is 800 kg.
To know more about weight here
https://brainly.com/question/10069252
#SPJ4
3. Determine the complex power for the following cases: (i) P = P1W, Q = Q1 VAR (capacitive) (ii) Q = Q2 VAR, pf = 0.8 (leading) (iii) S = S1 VA, Q = Q2 VAR (inductive)
The complex power was determined for three cases: (i) P = P1 W, Q = Q1 VAR (capacitive), resulting in (P1 + jQ1) W; (ii) Q = Q2 VAR, pf = 0.8 (leading), resulting in 1.25Q ∠ 53.13°; and (iii) S = S1 VA, Q = Q2 VAR (inductive), resulting in (S1 + jQ2) VA.
(i) P = P1 W, Q = Q1 VAR (capacitive)
We have:
Q = |Vrms||Irms|sin(θ) < 0
which implies
Irms = |Irms| ∠ θ = -j|Irms|sin(θ)
Using the formula for complex power, we have:
P + jQ = VrmsIrms* = |Vrms||Irms|∠θ
Substituting the given values, we get:
P + jQ = (P1 + jQ1) W
Therefore, the complex power is (P1 + jQ1) W.
(ii) Q = Q2 VAR, pf = 0.8 (leading)
We can calculate the real power as follows:
cos(θ) = pf = 0.8
sin(θ) = -√(1 - cos^2(θ)) = -0.6
|Vrms||Irms| = S = Q/cos(θ) = Q/0.8 = 1.25Q
Using the formula for complex power, we have:
P + jQ = VrmsIrms* = |Vrms||Irms|∠θ
Substituting the calculated values, we get:
P + jQ = 1.25Q ∠ -θ = 1.25Q ∠ 53.13°
The complex power is 1.25Q ∠ 53.13°.
(iii) S = S1 VA, Q = Q2 VAR (inductive)
We can calculate the real power using the formula for apparent power:
|Vrms||Irms| = S/|cos(θ)| = S/1 = S
Using the formula for complex power, we have:
P + jQ = VrmsIrms* = |Vrms||Irms|∠θ
Substituting the given values, we get:
P + jQ = (S1 + jQ2) VA
Therefore, the complex power is (S1 + jQ2) VA.
To know more about complex power, visit:
brainly.com/question/32089539
#SPJ11
A marble with a mass of 0.04 kg and a volume of 1.00×10⁻⁵ m³ is dropped in a glass of dimethyl sulfoxide, which sinks to the bottom of the glass. If dimethyl sulfoxide has a density of 1100 kg/m³, what is the magnitude of the buoyant force in newtons? Round to the nearest hundredth (0.01)
The magnitude of the buoyant force is approximately 0.11 N.
To find the magnitude of the buoyant force, we will use the following formula:
B = ρ × g × V
where
B is the magnitude of the buoyant force,
ρ is the density of the liquid,
g is the acceleration due to gravity and
V is the volume of the object displaced.
We are given the following:
mass of the marble, m = 0.04 kg
volume of the marble, V = 1.00 × 10⁻⁵ m³
density of the liquid, ρ = 1100 kg/m³
acceleration due to gravity, g = 9.81 m/s²
To find the volume of liquid displaced, we use the following formula:
V_displaced = V_object = 1.00 × 10⁻⁵ m³
The magnitude of the buoyant force is given by:
B = ρ × g × V_displaced
B = 1100 kg/m³ × 9.81 m/s² × 1.00 × 10⁻⁵ m³
B = 0.10779 N ≈ 0.11 N
Therefore, the magnitude of the buoyant force is approximately 0.11 N.
Learn more about the buoyant force:
brainly.com/question/11884584
#SPJ11
vires B and C. Find the force per unit length exerted on the following. (Express your answers in vector form.) (a) wire A f
A
= 1/m (b) wire B f
B
= N/m
The required force per unit length exerted on the wires are as follows: fA = (0 N/m, 5.03 × 10^-5 N/m, 0 N/m). fB = (0 N/m, 3.02 × 10^-4 N/m, 0 N/m)
Given, Charge per unit length on wire A = λA
Current in wire B = IB
Charge per unit length on wire C = λC
Finding the force per unit length exerted on the wires, A. Force per unit length on wire ABy using the formula for the force per unit length between two parallel wires, Force per unit length on wire A is given as, fA = μ₀/4π * (λA * IB) / dB.
Force per unit length on wire BBy using the formula for the force per unit length between two parallel wires, Force per unit length on wire B is given as,fB = μ₀/4π * (IB * λC) / dB.
Thus, the force per unit length exerted on wire A and wire B is given by the following expression.
fA = μ₀/4π * (λA * IB) / dB
fA = 4π × 10^-7 * (1 A/m * 2 A/m) / 0.05 m
fA = 5.03 × 10^-5 N/m
fA = (0 N/m, 5.03 × 10^-5 N/m, 0 N/m)
fB = μ₀/4π * (IB * λC) / d B
fB = 4π × 10^-7 * (2 A/m * 3 A/m) / 0.05 m
fB = 3.02 × 10^-4 N/m
fB = (0 N/m, 3.02 × 10^-4 N/m, 0 N/m)
Hence, the required force per unit length exerted on the wires are as follows: fA = (0 N/m, 5.03 × 10^-5 N/m, 0 N/m). fB = (0 N/m, 3.02 × 10^-4 N/m, 0 N/m)
Question: Wires B and C. Find the force per unit length exerted on the following. (Express your answers in vector form.)
(a) wire A [tex]f_{A}[/tex] = 1/m
(b) wire B [tex]f_{B}[/tex] = N/m
To learn about force here:
https://brainly.com/question/12785175
#SPJ11
The acceleration of a block attached to a spring is given by - (0.346m/s²) cos ([2.29rad/s]t). Part A What is the frequency of the block's motion? f = ________ Hz
Part B What is the maximum speed of the block? vmax = _____________ m/s
Answer: Therefore, the frequency of the block's motion is f = 0.834 Hz and the maximum speed of the block is vmax = 0.793 m/s.
The acceleration of a block attached to a spring is given by - (0.346m/s²) cos ([2.29rad/s]t)
Part A: The frequency of the block's motion:
Frequency is defined as the number of cycles per second. The equation of motion of an oscillating block attached to a spring is given as:
a = -ω²x
where, ω = 2πf ;a = acceleration of the oscillating block attached to a spring, ω = angular frequency, f = frequency, x = displacement.
Thus,ω² = (2.29 rad/s)²
= 5.2441 rad²/s²
ω = 2πf
= 5.2441f
= 0.834 Hz
Part B: The maximum speed of the block vmax =
vmax = (1/ω) * maximum value of a(1/ω) = 1/ (2.29 rad/s) = 0.4365 s.
Thus, vmax = (0.346 m/s²)/ 0.4365 s
= 0.793 m/s
Therefore, the frequency of the block's motion is f = 0.834 Hz and the maximum speed of the block is vmax = 0.793 m/s.
Learn more about frequency: https://brainly.com/question/254161
#SPJ11
for a serial RLC circuit, let C = 50.0 pF, L = 25 mH and R = 8.0k Calculate the angular frequency of the circuit once the capacitor has been charged and connected to the other two elements of the circuit.
The angular frequency of the circuit, once the capacitor has been charged and connected to the other two elements, is approximately 892.47 rad/s.
The angular frequency (ω) of the serial RLC circuit, once the capacitor has been charged and connected to the other two elements of the circuit, can be calculated using the values of capacitance (C), inductance (L), and resistance (R).
The angular frequency (ω) of a serial RLC circuit is given by the formula:
ω = [tex]\frac{1}{\sqrt{LC} }[/tex]
In this case, the given values are:
C = 50.0 pF (picoFarads) = 50.0 × [tex]10^{-12}[/tex] F (Farads)
L = 25 mH (milliHenries) = 25 × [tex]10^{-3}[/tex] H (Henries)
Plugging these values into the formula, we can calculate the angular frequency as follows:
ω = 1 / √(50.0 × [tex]10^{-12}[/tex] F × 25 × [tex]10^{-3}[/tex] H)
= 1 / √(1250 × [tex]10^{-15}[/tex] F × H)
= 1 / √(1250 × [tex]10^{-15}[/tex] F × H)
= 1 / √(1.25 × [tex]10^{-12}[/tex] F × H)
= 1 / (1.118 × [tex]10^{-6}[/tex] F × H)
≈ 892.47 rad/s
Therefore, the angular frequency of the circuit, once the capacitor has been charged and connected to the other two elements, is approximately 892.47 rad/s.
Learn more about frequency here:
https://brainly.com/question/2140860
#SPJ11
Rectangulars In a piston-cylinder arrangement air initially at V=2 m3, T=27°C, and P=2 atm, undergoes an isothermal expansion process where the air pressure becomes 1 atm. How much is the heat transfer in kJ? 0277 O 252 288 O 268
Given:
Initial volume V1 = 2 m³
Initial temperature T1 = 27 °C = 27 + 273 = 300 K
Initial pressure P1 = 2 atm = 2.03 bar
Final pressure P2 = 1 atm = 1.01325 bar
Process: Isothermal expansion
Work done by the gas, W = nRT ln (P1/P2)where n is the number of moles of air
R is the universal gas constant = 8.314 JK⁻¹mol⁻¹
T is the absolute temperature of the system ln is the natural logarithm
Heat transferred, q = -W
This is because the system loses energy, thus heat transferred is negative.
W = nRT ln (P1/P2)
= (P1V1/RT)RT ln (P1/P2)
= P1V1 ln (P1/P2)P1
= 2.03 bar
= 203 kPaP2
= 1.01325 bar
= 101.325 kPaW
= P1V1 ln (P1/P2)/RTW
= 203 × 2 ln (203/101.325)/(8.314 × 300)
W = -1.263 kJ
Heat transferred, q = -Wq = 1.263 kJ (approx)
Therefore, the heat transfer in kJ is 1.263 kJ.
Learn more about Isothermal expansion here
https://brainly.com/question/31570849
#SPJ11
3 Ficks First Law EXAMPLE PROBLEM 6.1 Diffusion Flux Computation A plate of iron is exposed to a carburizing (carbon-rich) atmosphere on one side and a decarbur- izing (carbon-deficient) atmosphere on
Therefore, the flux of carbon through the plate is 3.75 × 10–11 kg/m2-s (kilograms per meter square per second).
Fick’s First Law provides a mathematical description of the diffusion of a solute through a semi-permeable barrier in order to determine the flux of solute. In terms of chemical engineering, the principle is applied to determine the rate of mass transport through a solid material. Fick’s First Law is given by J = -D(∂C/∂x) where J is the diffusion flux of the solute, C is the concentration of the solute, x is the spatial coordinate, and D is the diffusion coefficient. EXAMPLE PROBLEM 6.1: Diffusion Flux Computation. A plate of iron is exposed to a carburizing (carbon-rich) atmosphere on one side and a decarbur-izing (carbon-deficient) atmosphere on the other side. If the diffusion coefficient of carbon in iron is 2.5 × 10–11 m2/s and the concentration difference of carbon across the plate is 1.5 kg/m3, determine the flux of carbon through the plate.The diffusion flux J can be calculated by using the Fick's First Law equation as follows;J = -D(∂C/∂x)J = - 2.5 × 10–11 m2/s(1.5 kg/m3)J = -3.75 × 10–11 kg/m2-s. Therefore, the flux of carbon through the plate is 3.75 × 10–11 kg/m2-s (kilograms per meter square per second).
To know more about plate visit:
https://brainly.com/question/32793163
#SPJ11
The resistance of a wire, made of a homogenous material with a uniform diameter, is proportional to its length. Select one: True False
False. The resistance of a wire made of a homogeneous material with a uniform diameter is not proportional to its length.
According to Ohm's law, the resistance (R) of a wire is determined by its resistivity (ρ), length (L), and cross-sectional area (A). The relationship is given by the equation R = ρ * (L/A). From this equation, we can see that the resistance depends on both the length and the cross-sectional area of the wire.
When the length of the wire increases, the resistance also increases. This is because the longer wire provides more obstacles for the flow of electric current, resulting in higher resistance. However, the relationship between resistance and length is not directly proportional but rather linear.
In a wire with a uniform diameter, the cross-sectional area remains constant throughout its length. Therefore, the resistance is directly proportional to the length of the wire, assuming the resistivity of the material remains constant.
Learn more about resistance here:
https://brainly.com/question/29427458
#SPJ11
Find solutions for your homework
science
earth sciences
earth sciences questions and answers
no need explanation, just give me the answer pls 12. what is the origin of the moon? a. the moon was once a part of earth and was ejected from earth in the early solar system. b. the moon formed from debris following a major impact between earth and another astronomical body. c. the moon was captured by
Question: No Need Explanation, Just Give Me The Answer Pls 12. What Is The Origin Of The Moon? A. The Moon Was Once A Part Of Earth And Was Ejected From Earth In The Early Solar System. B. The Moon Formed From Debris Following A Major Impact Between Earth And Another Astronomical Body. C. The Moon Was Captured By
No need explanation, just give me the answer pls
12. What is the origin of the moon?
A.The moon was once a part of Earth and was ejected from Earth in the early solar system.B.The moon formed from debris following a major impact between Earth and another astronomical body.C.The moon was captured by Earth's gravity but formed elsewhere.D.The moon formed with Earth near where it is today.E.The correct answer is not given.
The answer to the question, "What is the origin of the moon?" is B. The moon formed from debris following a major impact between Earth and another astronomical body.
This theory, known as the giant impact hypothesis or the impactor theory, proposes that early in the history of the solar system, a Mars-sized object, often referred to as "Theia," collided with a young Earth. The impact was so powerful that it ejected a significant amount of debris into space. Over time, this debris coalesced to form the moon.
According to this hypothesis, the collision occurred approximately 4.5 billion years ago. The ejected material eventually formed a disk of debris around Earth, which then accreted to form the moon. The moon's composition is similar to Earth's outer layers, supporting the idea that it originated from Earth's own materials.
The giant impact hypothesis provides an explanation for various characteristics of the moon, such as its size, composition, and its orbit around Earth. It is currently the most widely accepted theory for the moon's origin, although further research and analysis continue to refine our understanding of this fascinating event in our solar system's history.
Learn more about astronomical
https://brainly.com/question/1764951
#SPJ11
What is the wavelength of a wave traveling with a speed of 3.0 m/s and the period of 6.0 s?
The wavelength of a wave with a 3.0 m/s speed and a 6.0 s period is 18.0 m.
To calculate the wavelength of a wave, we can use the wave equation:
v = λ / T
where v is the speed of the wave,
λ is the wavelength, and
T is the period.
Speed of the wave (v) = 3.0 m/s
Period (T) = 6.0 s
Substituting the given values into the wave equation:
3.0 m/s = λ / 6.0 s
To find the wavelength (λ), we can rearrange the equation:
λ = v * T
Substituting the given values:
λ = 3.0 m/s * 6.0 s
λ = 18.0 m
Therefore, the wavelength of the wave is 18.0 meters.
Learn more about wavelength here
https://brainly.com/question/16051869
#SPJ11
An old fashioned computer monitor accelerates electrons and directs them to the screen in order to create an image.
If the accelerating plates are 0.958 cmcm apart, and have a potential difference of 2.60×104 VV , what is the magnitude of the uniform electric field between them?
The magnitude of the uniform electric field between the accelerating plates is approximately 2.71 × [tex]10^6[/tex] V/m.
The magnitude of the uniform electric field between the accelerating plates can be determined using the formula E = V/d, where E is the electric field, V is the potential difference, and d is the distance between the plates.
In this case, the electric field magnitude is obtained by dividing the potential difference of 2.60×104 V by the plate separation distance of 0.958 cm.
The magnitude of the electric field (E) between the accelerating plates can be found using the formula E = V/d, where V is the potential difference between the plates and d is the distance between the plates.
In this case, the given potential difference is 2.60×104 V and the plate separation distance is 0.958 cm.
However, it is important to note that the distance should be converted to meters to ensure consistency with the SI units used for electric field.
Converting 0.958 cm to meters, we have:
d = 0.958 cm = 0.958 × 10^(-2) m
Now, we can substitute the values into the formula:
E = V/d = (2.60×104 V) / (0.958 × 10^(-2) m)
Simplifying the expression, we divide the numerator by the denominator:
E ≈ 2.71 × [tex]10^6[/tex] V/m
Therefore, the magnitude of the uniform electric field between the accelerating plates is approximately 2.71 × [tex]10^6[/tex] V/m.
Learn more about electric field here:
https://brainly.com/question/30544719
#SPJ11
A proton (rest mass 1.67 x 10-27kg) has total energy that is 7.2 times its rest energy. What is a) the kinetic energy of the proton? 9.3186(10^-10) J b) the magnitude of the momentum of the proton? x10-18kg. m/s. c) the speed of the proton?
a) Kinetic energy of the proton The kinetic energy of the proton can be calculated by the formula shown below: Kinetic energy (K.E.) = Total energy - Rest energy K.E. = 7.2 × rest energy For a proton with rest mass of 1.67 × 10⁻²⁷ kg, the rest energy can be calculated as: Rest energy (E₀) = m₀c²where m₀ = 1.67 × 10⁻²⁷ kg and c = 3 × 10⁸ m/s E₀ = (1.67 × 10⁻²⁷) × (3 × 10⁸)²= 1.505 × 10⁻¹⁰ J.
The kinetic energy of the proton is therefore given by: K.E. = 7.2 × E₀= 7.2 × 1.505 × 10⁻¹⁰= 1.0836 × 10⁻⁹ J= 9.3186 × 10⁻¹⁰ J
b) Magnitude of the momentum of the proton The magnitude of the momentum of the proton can be obtained by using the formula: Total energy = √(p²c² + (m₀c²)²)where p is the momentum of the proton and m₀c² is its rest energy. Rearranging the equation to solve for p gives: p = √((Total energy)² - (m₀c²)²)/cc = 3 × 10⁸ m/s Total energy = 7.2 × E₀= 7.2 × 1.505 × 10⁻¹⁰= 1.0836 × 10⁻⁹ J Thus, the magnitude of the momentum of the proton is given by: p = √((1.0836 × 10⁻⁹)² - (1.505 × 10⁻¹⁰)²)/3 × 10⁸= 2.148 × 10⁻¹⁸ kg m/s
c) Speed of the proton The speed of the proton can be calculated using the formula: v = p/m where p is the momentum and m is the mass of the proton. v = p/m= (2.148 × 10⁻¹⁸)/(1.67 × 10⁻²⁷)= 1.285 × 10⁹ m/s= 1.285 × 10⁹/3 × 10⁸= 4.283 × 10⁰ m/s= 4.28 × 10⁰ m/s. Therefore, the speed of the proton is 4.28 × 10⁰ m/s.
To know more about momentum visit:
https://brainly.com/question/14082501
#SPJ11
choose the correct answer For this system The heater is off when O Comparator Reference value Te • TaTd • Ta=0 • Td=0 True Emor Heater signal False Temperature measuring device Room Any values for dynamic characteristics are indicated in instrument data sheets and only apply when the instrument is used underspecified environmental conditions. Room temperature . true or false?
The statement "The heater is off when O Comparator Reference value Te • TaTd • Ta=0 • Td=0" is true and The second statement "Any values for dynamic characteristics are indicated in instrument data sheets and only apply when the instrument is used under specified environmental conditions. Room temperature." is false.
The statement is false because instrument data sheets provide detailed information about the dynamic characteristics of instruments, such as response time, accuracy, or frequency response. However, these characteristics are specified under specific environmental conditions, which may include temperature ranges, humidity levels, or other factors. Merely assuming "room temperature" is not sufficient to accurately apply the specified values.
Instrument performance can be significantly influenced by environmental factors, and variations in temperature can affect the instrument's behavior and measurements. Different materials used in instrument construction can exhibit varying thermal expansion properties, leading to potential changes in calibration and accuracy.
To ensure the instrument operates as intended and provides accurate results, it is crucial to consult the instrument data sheet and consider the specified environmental conditions. Adhering to the recommended operating conditions will help maintain the instrument's performance, reliability, and accuracy in real-world applications.
To know more about Heater click here:
https://brainly.com/question/29547273
#SPJ11