The amount of heat needed to melt 144 g of solid hexane and bring it to a temperature of -30.5°C is approximately 9.09 kJ.
To calculate the amount of heat needed to melt the solid hexane and bring it to a specific temperature, we need to consider two steps: the heat required for melting (phase change) and the heat required to raise the temperature.
1. Heat required for melting:
The heat of fusion (ΔHfus) represents the amount of heat needed to melt a substance at its melting point without changing its temperature. For hexane, the heat of fusion is typically given as 9.92 kJ/mol.
First, we need to calculate the number of moles of hexane in 144 g:
Molar mass of hexane (C6H14) = 6(12.01 g/mol) + 14(1.01 g/mol) = 86.18 g/mol
Number of moles = mass / molar mass = 144 g / 86.18 g/mol
Now, we can calculate the heat required for melting:
Heat for melting = ΔHfus * number of moles
2. Heat required to raise the temperature:
The specific heat capacity (C) represents the amount of heat needed to raise the temperature of a substance by 1 degree Celsius. For hexane, the specific heat capacity is typically given as 1.74 J/g°C.
Now, we need to calculate the change in temperature:
Change in temperature = final temperature - initial temperature = (-30.5°C) - (0°C)
Finally, we can calculate the heat required to raise the temperature:
Heat for temperature change = mass * specific heat capacity * change in temperature
To obtain the total heat needed, we sum up the heat for melting and the heat for temperature change.
Let's calculate the values:
Number of moles = 144 g / 86.18 g/mol ≈ 1.67 mol
Heat for melting = 9.92 kJ/mol * 1.67 mol = 16.53 kJ
Heat for temperature change = 144 g * 1.74 J/g°C * (-30.5°C - 0°C) = -7435.68 J
Total heat needed = Heat for melting + Heat for temperature change
Total heat needed = 16.53 kJ + (-7435.68 J)
Make sure to convert the units to have a consistent representation. In this case, we'll convert the total heat needed to kilojoules (kJ):
Total heat needed = (16.53 kJ - 7.43568 kJ) ≈ 9.09432 kJ
Therefore, the amount of heat needed to melt 144 g of solid hexane and bring it to a temperature of -30.5°C is approximately 9.09 kJ.
learn more about heat capacity
https://brainly.com/question/28302909
#SPJ11
A truck move across a 25 - m simple span. The wheel loads are P. = 36 kN and P2 = 142 kN separated by 4.3 m, and P2 = 142 kN at 7.6 m from P. Determine (a) the maximum shear in kN, (b) the maximum moment under each load in kN.m, (c) the maximum moment of the group of moving loads in kN.m.
The maximum shear is -142 kN (upwards). The maximum moment under load P1 is 900 kN.m, and the maximum moment under load P2 is 2471.8 kN.m. The maximum moment of the group of moving loads is 3371.8 kN.m.
To determine the maximum shear, maximum moment under each load, and the maximum moment of the group of moving loads, we can use the principles of statics and structural analysis.
Given:
P1 = 36 kN (load 1)
P2 = 142 kN (load 2)
Distance between P1 and P2 = 4.3 m
Distance between P2 and support = 7.6 m
(a) Maximum Shear:
The maximum shear occurs when the truck is positioned to create the largest shear force on the span. Since the loads are concentrated at specific points, the maximum shear will occur directly below each load.
Shear at P1 = -P1 = -36 kN (upwards)
Shear at P2 = -P2 = -142 kN (upwards)
Therefore, the maximum shear is -142 kN (upwards).
(b) Maximum Moment under Each Load:
The maximum moment occurs when the load is positioned to create the largest bending moment at the span's cross-section. The moment at each load can be calculated using the following formula:
Moment at P1 = P1 * a
Moment at P2 = P2 * b
Where:
a = distance from P1 to the support (25 m)
b = distance from P2 to the support (25 - 7.6 = 17.4 m)
Moment at P1 = 36 kN * 25 m = 900 kN.m
Moment at P2 = 142 kN * 17.4 m = 2471.8 kN.m
Therefore, the maximum moment under load P1 is 900 kN.m, and the maximum moment under load P2 is 2471.8 kN.m.
(c) Maximum Moment of the Group of Moving Loads:
To determine the maximum moment of the group of moving loads, we need to consider the combination of moments created by the loads.
Maximum Moment = Moment at P1 + Moment at P2
Maximum Moment = 900 kN.m + 2471.8 kN.m = 3371.8 kN.m
Therefore, the maximum moment of the group of moving loads is 3371.8 kN.m.
To know more about maximum shear visit :
https://brainly.com/question/32765327
#SPJ11
The histogram below shows information about the
temperature at noon in some different cities on one
day.
a) Complete the grouped frequency table by
working out the values that should replace x, y and
2.
b) Calculate an estimate for the mean temperature.
If your answer is a decimal, give it to 1 d.p.
Frequency density
5-
3
N
1-
2
-∞
6
8
Temperature (°C)
10
12
Temperature, t (°C) Frequency
2≤t<4
4≤t<6
6≤ t < 10
x
Y
N
The grouped frequency table is
Temperature Frequency
2 < z < 4 3
4 < z < 6 5
6 < z < 10 4
The estimate for the mean temperature is 5.5
Completing the grouped frequency tableFrom the question, we have the following parameters that can be used in our computation:
The histogram
The values of x, y and z are the frequencies of the temperatures
Working out the values that should replace x, y and z, we have
Temperature Frequency
2 < z < 4 3
4 < z < 6 5
6 < z < 10 4
b) Calculating an estimate for the mean temperature.Start by calculating the midpoint of the temperatures
Temperature Frequency
3 3
5 5
8 4
So, we have
Mean = (3 * 3 + 5 * 5 + 8 * 4)/(3 + 5 + 4)
Evaluate
Mean = 5.5
Hence, the estimate for the mean temperature is 5.5
Read more about histogram at
https://brainly.com/question/25983327
#SPJ1
For the function h(x)=2^(6x+1), find two functions f(x) and g(x) such that h(x)=f(g(x))
The functions that form the composite function h(x) in this problem are given as follows:
[tex]f(x) = 2^x[/tex]g(x) = 6x + 1.How to obtain the functions?The composite function for this problem is given as follows:
[tex]h(x) = 2^{(6x + 1)}[/tex]
For a composite function, the inner function is applied as the input to the outer function.
Considering the exponential, the inner function is given as follows:
[tex]f(x) = 2^x[/tex]
The exponential is of 6x + 1, hence the outer function is given as follows:
g(x) = 6x + 1.
More can be learned about composite functions at https://brainly.com/question/10687170
#SPJ4
How do you set up the equations needed to solve the chemical equilibrium of methane steam reforming using the law of mass action and the reactions stoichiometry? How the equilibrium constant of the reactions changes with temperature. What are the main characteristics of this method to solve chemical equilibrium compared to non-stoichiometric methods such as the Lagrange Multiplier method?
The equations for the chemical equilibrium of methane steam reforming using the law of mass action and reactions stoichiometry.
The methane steam reforming reaction can be represented as follows:
CH4 + H2O ⇌ CO + 3H2
The equilibrium constant expression for this reaction is given by the law of mass action as:
Kp = (P_CO * P_H2^3) / (P_CH4 * P_H2O)
Where Kp is the equilibrium constant at constant pressure, and P represents the partial pressure of the respective species involved.
The equilibrium constant of a reaction is temperature-dependent and changes with temperature. In general, the equilibrium constant (K) for a reaction is related to the standard Gibbs free energy change (ΔG°) for the reaction through the equation:
ΔG° = -RT ln(K)
Where R is the gas constant and T is the temperature in Kelvin. As the temperature changes, the value of the equilibrium constant will also change.
Regarding the characteristics of using the law of mass action and reactions stoichiometry to solve chemical equilibrium compared to non-stoichiometric methods like the Lagrange Multiplier method, some key points are:
Stoichiometric methods: These methods are based on the stoichiometry of the chemical reactions and the law of mass action. They use equilibrium constant expressions and solve systems of algebraic equations to determine the equilibrium concentrations or pressures of the species involved.
Conservation of mass: Stoichiometric methods explicitly consider the conservation of mass and the stoichiometric relationships between reactants and products. They are useful for determining the equilibrium composition in terms of species concentrations or pressures.
Simplicity: Stoichiometric methods are relatively straightforward and do not involve complex mathematical techniques like optimization or nonlinear programming used in non-stoichiometric methods.
On the other hand, non-stoichiometric methods like the Lagrange Multiplier method or minimization of Gibbs free energy can handle more complex equilibrium problems involving non-ideal behavior, multiple constraints, and phase equilibrium.
Overall, stoichiometric methods based on the law of mass action and reactions stoichiometry are simpler and effective for many chemical equilibrium problems, but non-stoichiometric methods are more versatile and can handle more complex scenarios.
To more about equilibrium, visit:
https://brainly.com/question/517289
#SPJ11
The results of a constant head permeability test for a fine sand and sample having a diameter of 80 mm and length of 60 mm are as follows: Constant head difference = 40 cm Time of collection of water = 10 mins Weight of water collected = 430 kg Find the hydraulic conductivity in cm ^3/min
The hydraulic conductivity of the given fine sand sample is 0.514 cm^3/min .
The hydraulic conductivity is an essential parameter in hydrogeology that quantifies the ability of water to flow through a porous medium under the influence of a hydraulic gradient.
It is the ratio of the discharge of water through the porous medium to the cross-sectional area and hydraulic gradient that generates the discharge. The hydraulic conductivity is expressed in units of cm^3/min.
To find the hydraulic conductivity, the equation is given as:
Hydraulic conductivity = (Weight of water collected × L)/(t × A × h)
Where:L = Length of the sample = 60 mm = 6 cm.
A = Cross-sectional area of the sample = (π × d^2) / 4 = (π × 80^2) / 4 = 5026.55 mm^2.
t = Time of collection of water = 10 mins.
h = Constant head difference = 40 cm.
Weight of water collected = 430 kg = 430 × 10^3 g.
The given values are substituted in the above equation,
Hydraulic conductivity = (Weight of water collected × L)/(t × A × h)
Hydraulic conductivity = (430 × 10^3 g × 6 cm)/(10 mins × 5026.55 mm^2 × 40 cm)
Hydraulic conductivity = 0.514 cm^3/min
Therefore, the hydraulic conductivity of the given fine sand sample is 0.514 cm^3/min.
Learn more about hydraulic conductivity
https://brainly.com/question/31920573
#SPJ11
The hydraulic conductivity of the fine sand sample is approximately 0.085 cm^3/min.
To calculate the hydraulic conductivity of the fine sand sample, we can use the formula:
K = (Q * L) / (A * H * t)
where:
K is the hydraulic conductivity,
Q is the weight of water collected (430 kg),
L is the length of the sample (60 mm or 6 cm),
A is the cross-sectional area of the sample (π * (d/2)^2, where d is the diameter of the sample),
H is the constant head difference (40 cm),
and t is the time of collection of water (10 mins or 10/60 hours).
First, let's calculate the cross-sectional area:
A = π * (80/2)^2 = π * 40^2 = 1600π cm^2.
Next, let's convert the time to hours:
t = 10/60 = 1/6 hour.
Now, we can substitute the values into the formula and calculate the hydraulic conductivity:
K = (430 * 6) / (1600π * 40 * (1/6))
= (2580) / (9600π)
≈ 0.085 cm^3/min (rounded to 3 decimal places).
Therefore, the hydraulic conductivity of the fine sand sample is approximately 0.085 cm^3/min.
Learn more about hydraulic conductivity
https://brainly.com/question/31920573
#SPJ11
Consider the following function.
f(x)=√x - 1
Which of the following graphs corresponds to the given function?
The graph the corresponds to the function f(x)=√(x - 1) is plotted and attached
What is a radical graphA radical graph, also known as a square root graph, represents the graph of a square root function. A square root function is a mathematical function that calculates the square root of the input value.
key features of a radical graph is the shape: The shape of a square root graph is a concave upward curve. The steepness or flatness of the curve depends on the value of the constant a. A larger value of a results in a steeper curve, while a smaller value of a results in a flatter curve.
Learn more about square root function at
https://brainly.com/question/29111434
#SPJ1
Question 4 6 points The increase in mix water content of concrete results in a higher consistency. However, an excessive amount of water may cause some problems in fresh concrete such as ...... or ...
While increasing the mix water content can improve the consistency of concrete, excessive water can lead to problems such as segregation and bleeding, which can weaken the concrete's structure.
When the mix water content of concrete increases, it leads to a higher consistency. However, excessive amounts of water can cause problems in fresh concrete. Two common problems caused by excessive water content are segregation and bleeding.
1. Segregation: Excessive water causes the solid particles in the concrete mix to settle, resulting in the separation of the mix components. This can lead to non-uniform distribution of aggregates and cement paste, affecting the strength and durability of the concrete.
2. Bleeding: Excess water in the concrete mix tends to rise to the surface, pushing air bubbles and excess water out. This process is called bleeding. It forms a layer of water on the concrete surface, which can weaken the top layer and reduce the concrete's strength.
Both segregation and bleeding can compromise the structural integrity and overall quality of the concrete. It's important to maintain the appropriate water-to-cement ratio to achieve the desired consistency without compromising the performance of the concrete.
In summary, While adding more water to the mix might make concrete more consistent, too much water can cause issues like segregation and bleeding that can impair the concrete's structure.
learn more about consistency from given link
https://brainly.com/question/19129356
#SPJ11
Select the only correct statement from the list below Select one: a. On de-excitation in Atomic Emission Spectrometry, all metals emit radiation in the visible region of the electromagnetic spectrum
b. None of the statements listed here is correct c. Living things need metallic macronutrients such as Cobalt-containing compounds in their diet for proper growth and development d. The Flame Test for qualitative analysis is based on the principles of Atomic Absorption
The correct statement among the given options is "The Flame Test for qualitative analysis is based on the principles of Atomic Absorption."
The Flame Test is a method used for qualitative analysis of elements. It involves heating a metallic salt mixed with a hydrochloric acid and methanol solution in a flame. The resulting color of light emitted during this process is characteristic and can be used to identify the presence of specific elements.
This test is based on the principles of Atomic Absorption. In Atomic Absorption Spectroscopy, the elements are vaporized in a flame or graphite furnace and then excited by absorbing light at a specific wavelength. The atoms in the vapor absorb the energy of the incident light, leading to their excitation. Upon returning to the ground state, they emit light at specific wavelengths, which can be detected and analyzed.
On the other hand, Atomic Emission Spectrometry involves the emission of light of various wavelengths during the de-excitation process. It is important to note that not all metals emit radiation in the visible region of the electromagnetic spectrum.
Regarding the incorrect options, option (a) is incorrect because Atomic Emission Spectrometry does not involve absorption of light by the atoms. Option (c) is incorrect because cobalt is not considered an essential element for living organisms and is not classified as a metallic macronutrient. Option (b) is also incorrect as it contradicts the fact that one of the given statements is correct, which is the statement about the Flame Test and Atomic Absorption.
Learn more about analysis
https://brainly.com/question/33490941
#SPJ11
Determine the spontaneity of this reaction:
4HN3(g) + 3O2(g) --> 2N2(g) + 6H2O(g) Delta Hrxn= -1267 kJ
A. The reaction is spontaneous at high temperatures
B. The reaction is NOT spontaneous at any temperatures
C. The reaction is spontaneous at low temperatures
D. The reaction is spontaneous at all temperatures
E. It is impossible to determine the reaction spontaneity without additional information
We cannot definitively conclude the spontaneity of the reaction. The correct answer is E: It is impossible to determine the reaction spontaneity without additional information.
The spontaneity of a reaction can be determined by considering the sign of the change in enthalpy (ΔHrxn) and the change in entropy (ΔSrxn). In this case, the given reaction has a negative ΔHrxn (-1267 kJ), indicating that it is exothermic and releases energy.
To determine the spontaneity, we need to consider the relationship between ΔHrxn and ΔSrxn using the Gibbs free energy equation: ΔGrxn = ΔHrxn - TΔSrxn
where ΔGrxn is the change in Gibbs free energy, T is the temperature in Kelvin, and ΔSrxn is the change in entropy.
Since the question does not provide any information about the change in entropy, we cannot directly calculate ΔGrxn. However, we can use the sign of ΔHrxn to make an inference.
If a reaction has a negative ΔHrxn and ΔSrxn is positive, the reaction will be spontaneous at all temperatures because the negative term (-TΔSrxn) will eventually overcome the negative ΔHrxn term, resulting in a negative ΔGrxn. This means that the reaction is thermodynamically favorable.
On the other hand, if ΔHrxn is negative and ΔSrxn is negative, the reaction will only be spontaneous at low temperatures, as the negative term (-TΔSrxn) will become more dominant at higher temperatures, making the reaction non-spontaneous.
Since we do not have information about ΔSrxn, we cannot determine its sign. Therefore, we cannot definitively conclude the spontaneity of the reaction. The correct answer is E: It is impossible to determine the reaction spontaneity without additional information.
Learn more about spontaneity:
https://brainly.com/question/30127476
#SPJ11
please help:
given WXYZ is similar to RSTV. find ST
The calculated value of the length of the segment ST is 13.5
How to determine the length of the segment STFrom the question, we have the following parameters that can be used in our computation:
The trapezoids
The length of the segment ST is then calculated as
XY/XW = ST/SR
substitute the known values in the above equation, so, we have the following representation
9/12 = ST/18
So, we have
ST = 18 * 9/12
Evaluate
ST = 13.5
Hence, the length of the segment ST is 13.5
Read more about similar shapes at
https://brainly.com/question/32122930
#SPJ1
Question 5 A hydrate of nickel(II) chloride (NiCl2-XH₂O) decomposes to produce 29.5% water & 70.5% AC. Calculate the water of crystallization for this hydrated compound. (The molar mass of anhydrous NiCl2 is 129.6 g/mol.) Type your work for partial credit. Answer choices: 3, 4, 7, or 8.
The water of crystallization for this hydrate is 3.
To calculate the water of crystallization for the hydrate of nickel(II) chloride (NiCl2-XH₂O), we need to analyze the given information.
The compound is described as a hydrate, which means it contains water molecules in its crystal structure. It decomposes to produce 29.5% water and 70.5% anhydrous compound (AC).
To find the water of crystallization, we need to determine the number of water molecules (X) in the formula NiCl2-XH₂O.
First, let's find the molar mass of the anhydrous compound, NiCl2. The molar mass of anhydrous NiCl2 is given as 129.6 g/mol.
Next, let's assume we have 100 grams of the compound. Since 29.5% of the compound is water, the mass of water present is 29.5 grams.
Now, we can find the mass of the anhydrous compound by subtracting the mass of water from the total mass of the compound:
100 g - 29.5 g = 70.5 g
Next, let's convert the mass of the anhydrous compound to moles. We can use the molar mass of NiCl2 to do this:
70.5 g / 129.6 g/mol = 0.544 moles of NiCl2
Now, let's calculate the moles of water by using the molar mass of water (18.015 g/mol):
29.5 g / 18.015 g/mol = 1.636 moles of water
To find the ratio of water to anhydrous compound, we divide the moles of water by the moles of NiCl2:
1.636 moles water / 0.544 moles NiCl2 = 3 moles water : 1 mole NiCl2
From the ratio, we can see that the formula of the hydrated compound is NiCl2-3H₂O. This means that the water of crystallization for this hydrate is 3.
Therefore, the correct answer is 3.
Learn more about hydrated compound:
https://brainly.com/question/16275027
#SPJ11
A 150 L tank contains 100 L of water. A solution with a salt concentration of 0.1 kg/L is added to the tank at a rate of 5 L/min. The solution is kept mixed and is drained from the tank at a rate of 3 L/min. Determine the concentration of the mixture at the time the tank fills to maximum capacity.
The volume of the mixture in the tank will increase at a rate of 2 L/min because the inflow rate is 5 L/min and the outflow rate is 3 L/min. The tank's capacity is 150 L, and it currently contains 100 L of water.
When the tank is completely filled, the amount of salt in the tank can be calculated. Since 0.1 kg of salt is present in 1 L of the solution,
0.1 kg/L × 5 L/min × 60 min/hour = 30 kg/hour of salt is added to the tank.
When 3 L/min of the mixture is drained, the concentration of salt decreases.
30 kg/hour ÷ (5 L/min - 3 L/min)
= 15 kg/L
When the tank is completely filled, the amount of salt in the mixture is 15 kg/L.
Answer:
Concentration of mixture when the tank fills to maximum capacity is 15 kg/L.
To know more about increase visit:
https://brainly.com/question/33491846
#SPJ11
PLEASE HELP ME IM BEING TIMED
Answer: to find it:
to find the mean: add up all of the numbers and divide by the number of numbers listed. ex: 2, 4, 9
2+4+9=15/3= mean = 5
Step-by-step explanation:
Step 1: Collect the data for the two variables you want to determine the correlation for. The data should be continuous and normally distributed.
Step 2: Calculate the mean of both variables.
Step 3: Calculate the standard deviation of both variables.
Step 4: Calculate the covariance of the two variables using the formula below: `Cov(X, Y) = Σ [(Xi - Xmean) * (Yi - Ymean)] / (n-1)
Step 5: Calculate the correlation coefficient using the formula below: `r = Cov(X, Y) / (SD(X) * SD(Y))` where r is the correlation coefficient, Cov is the covariance, SD is the standard deviation, X is the first variable, Y is the second variable, Xi and Yi are the individual values of X and Y, X mean and Y mean are the means of X and Y, and n is the number of observations. The resulting value of r ranges from -1 to +1. A value of -1 indicates a perfect negative correlation, a value of 0 indicates no correlation and a value of +1 indicates a perfect positive correlation
Question 2 A layer of dry sand that is 3,0m thick lies on a clay stratum that is saturated. The water table is 2,0m below the ground surface. The dry sand has the following properties G, 2. 65 and e-0, 65 while the saturated clay has the following G,- 2, 82 and e=0, 91. Use g =9,81 m/s² 2.1 2.2 Determine the effective stress at a depth of 6. Om below the ground surface (8) Determine the effective stress at the same depth as in 2.1 if the water table is lowered by 300mm (meaning a 300mm drawdown). (5) [13]
2.1 Determination of effective stress at a depth of 6.0m below the ground surface Effective stress can be calculated as follows:Effective stress = (Total stress – Pore pressure)Where,Pore pressure = ϒw * Depth of the water table
Therefore, the effective stress at the same depth as in 2.1 when water table is lowered by 300mm (0.3m) is 144.3441 kN/m².
Total stress = (ϒsand * Depth of the dry sand) + (ϒclay * Depth of the clay)
ϒw = unit weight of water
ϒsand = unit weight of sand
ϒclay = unit weight of clay Given, Depth of the dry sand (zs) = 3.0m
Water table depth (zw) = 2.0m
Depth of interest (z) = 6.0m
Unit weight of water (ϒw) = 9.81 kN/m³ (given)
Unit weight of sand (ϒsand) = 2.65 * 9.81 = 25.9815 kN/m³ (given)
Unit weight of clay (ϒclay) = 2.82 * 9.81 = 27.6922 kN/m³ (given)
Effective stress = (Total stress – Pore pressure)
Pore pressure = ϒw *
Depth of the water table = 9.81 * 2.0 = 19.62 kN/m²
Total stress = (ϒsand * Depth of the dry sand) + (ϒclay * Depth of the clay)
= (25.9815 * 3.0) + (27.6922 * (6.0 - 3.0))
= 77.9445 + 83.0766 = 161.0211 kN/m²
Effective stress at a depth of 6.0m = (161.0211 – 19.62) = 141.4011 kN/m²
Therefore, the effective stress at a depth of 6.0m below the ground surface is 141.4011 kN/m².2.2 Determination of effective stress at the same depth as in 2.1 when water table is lowered by 300 mm (0.3 m)When the water table is lowered by 300mm (0.3m), the new depth of the water table becomes (2.0 – 0.3) = 1.7m.New pore pressure = ϒw * Depth of the new water table = 9.81 * 1.7 = 16.677 kN/m²New effective stress = (Total stress – New pore pressure)Total stress = (ϒsand * Depth of the dry sand) + (ϒclay * Depth of the clay)= (25.9815 * 3.0) + (27.6922 * (6.0 - 3.0))= 77.9445 + 83.0766= 161.0211 kN/m²New effective stress = (161.0211 – 16.677) = 144.3441 kN/m²
To know more about stress visit:
https://brainly.com/question/31366817
#SPJ11
The effective stress at a depth of 6.0m below the ground surface can be calculated using the formula:
Effective stress = (total stress - pore water pressure)
First, we need to determine the total stress at this depth. The total stress is the weight of the soil above the point of interest.
For the dry sand layer:
Total stress = unit weight of dry sand × thickness of sand
Total stress = (2.65 × 9.81) × 3.0
Total stress = 78.2275 kPa
For the saturated clay layer:
Total stress = unit weight of saturated clay × thickness of clay
Total stress = (2.82 × 9.81) × (6.0 - 2.0)
Total stress = 108.7044 kPa
Next, we need to determine the pore water pressure at this depth. The pore water pressure is the pressure exerted by the water in the soil.
Pore water pressure = unit weight of water × drawdown
Pore water pressure = (9.81 × 0.3)
Pore water pressure = 2.943 kPa
Now, we can calculate the effective stress:
Effective stress = total stress - pore water pressure
Effective stress = (78.2275 + 108.7044) - 2.943
Effective stress = 183.9889 - 2.943
Effective stress = 181.0459 kPa
For the second part of the question, if the water table is lowered by 300mm, the new pore water pressure would be:
Pore water pressure = (9.81 × 0.0)
Pore water pressure = 0.0 kPa
Therefore, the effective stress at the same depth (6.0m) with a 300mm drawdown would be equal to the total stress:
Effective stress = total stress
Effective stress = (78.2275 + 108.7044)
Effective stress = 186.9319 kPa
I hope this explanation helps! Let me know if you have any further questions.
To know more about EFFECTIVE STRESS click here-https://brainly.com/app/ask?q=effective+stress
#SPJ11
Density of rectangular blocks analysis Rectangular Block 1 Rectangular Block 2 Rectangular Block 3 Width (cm) Length (cm) 5.35 6.50 3.90 4.35 1.82 5.50 Height (cm) 1.80 1.70 1.82 Table view Mass (9) V
To calculate the density of the rectangular blocks, we would need the mass of each block in addition to the dimensions provided in the table view.
The given table provides the dimensions (width, length, and height) of three rectangular blocks, but it does not include the mass of each block. To calculate the density of a rectangular block, we need to know its mass and volume. The formula for density is:
Density = Mass / Volume
Without the mass values, it is not possible to calculate the density for each block. The mass of each block needs to be provided in order to perform the calculations.
The given information in the table view does not include the mass of the rectangular blocks. Therefore, we cannot calculate the density of the blocks based on the provided data. To determine the density, the mass of each block needs to be known.
To know more about density visit:
https://brainly.com/question/1354972
#SPJ11
There are two steel I beams in a construction cite. The I beam A
has 3" long stringer in the middle of the beam in the center of
shear web and the second beam (beam B) has multiple edge cracking
(0.1"
The two steel I beams in the construction site have different characteristics.
Beam A has a 3" long stringer in the middle of the beam, specifically in the center of the shear web.
On the other hand, beam B has multiple edge cracking measuring 0.1".
The stringer in beam A provides additional support and stiffness to the beam. It helps distribute the load evenly across the beam, preventing it from sagging or bending excessively.
The stringer is placed in the center of the shear web, which is responsible for transferring the shear forces in the beam. By reinforcing the shear web with a stringer, beam A becomes stronger and more resistant to deformation under shear loads.
On the other hand, beam B with multiple edge cracking is experiencing a structural issue.
Cracks on the edges can weaken the beam and compromise its integrity. These cracks can propagate and lead to further damage if not addressed.
It is important to assess the extent and severity of the cracking and take appropriate measures to repair or replace the beam if necessary.
Know more about stringer
https://brainly.com/question/33568794
#SPJ11
A reducing elbow in a horizontal pipe is used to deflect water flow by an angle of 45° from the flow direction while accelerating it. The elbow discharges water into the atmosphere at 30kg/s. The cross-sectional area of the elbow is 150cm² at the inlet and 25cm² at the exit. The elevation difference between the centers of the exit and the inlet is 40 cm. The total energy loss through the bend is 1.4169m of water. Determine the inlet pressure into the reducing bend Determine the total force in the X and Y directions Determine the pressure force in the X and Y directions Determine the anchoring force needed to hold the elbow in place
The inlet pressure into the reducing bend is 1.8 x [tex]10^6[/tex] Pa, the total force in the X and Y directions are 2.638 x [tex]10^5[/tex] N and 294.3 N, respectively, the pressure force in the X and Y directions are 4243.4 N and 9.81 N, respectively, and the anchoring force needed to hold the elbow in place is 4249.5 N.
How to calculate the inlet pressureFirst, let's determine the velocity of the water at the inlet and exit of the elbow
At the inlet:
Q = Av, where Q is the volumetric flow rate, A is the cross-sectional area, and v is the velocity of the water.
150 cm² = 0.015 m²
Q = 30 kg/s
30 kg/s = 0.015 m² x v
v = 2000 m/s
At the exit:
25 cm² = 0.0025 m²
Q = 30 kg/s
30 kg/s = 0.0025 m² x v
v = 12000 m/s
inlet pressure can be determined using Bernoulli's equation
[tex]P_1 + (1/2) \rho v_1^2 + \rho gh_1 = P_2 + (1/2) \rho v_2^2 + \rho gh_2[/tex]
where P is the pressure, ρ is the density of water, v is the velocity, and h is the elevation difference.
Assuming that the pressure at the exit is atmospheric pressure (101325 Pa)
[tex]P_1 + (1/2)\rho v_1^2 + \rho gh_1 = 101325 Pa + (1/2)\rho v_2^2 + \rho gh_2[/tex]
Substitute the values
[tex]P_1 + (1/2)(1000 kg/m^3)(2000 m/s)^2 + (1000 kg/m^3)(9.81 m/s^2)(0.4 m) = 101325 Pa + (1/2)(1000 kg/m^3)(12000 m/s)^2 + (1000 kg/m^3)(9.81 m/s^2)(0 m)[/tex]
Solving for P₁, we get:
P₁ = 1.8 x [tex]10^6[/tex] Pa
To determine the total force in the X and Y directions
The total force in the X direction is equal to the change in momentum of the water as it flows through the elbow:
F_x = ρQv₂ cos(45°) - ρQv₁
Substitute the values
F_x = (1000 kg/m³)(30 kg/s)(12000 m/s)(1/√2) - (1000 kg/m³)(30 kg/s)(2000 m/s)
F_x = 2.638 x [tex]10^5[/tex] N
The total force in the Y direction is equal to the weight of the water
F_y = mg
F_y = (30 kg/s)(9.81 m/s²)
F_y = 294.3 N
To determine the pressure force in the X and Y directions:
The pressure force in the X direction is equal to the difference in pressure at the inlet and outlet of the elbow multiplied by the area of the elbow
F_px = (P₁ - P₂)A₂
F_px = (1.8 x [tex]10^6[/tex] Pa - 101325 Pa)(0.0025 m²)
F_px = 4243.4 N
The pressure force in the Y direction is equal to the weight of the water in the elbow:
F_py = ρVg
V = Ah
V = (0.0025 m²)(0.4 m)
V = 0.001 m³
F_py = (1000 kg/m³)(0.001 m³)(9.81 m/s²)
F_py = 9.81 N
To determine the anchoring force needed to hold the elbow in place
The anchoring force is equal to the vector sum of the pressure force and the weight of the elbow:
F_anchor = √(F_p[tex]x^2[/tex] + (F_y - F_py[tex])^2)[/tex]
F_anchor = √((4243.4 N[tex])^2[/tex] + (294.3 N - 9.81 [tex]N)^2)[/tex]
F_anchor = 4249.5 N
Therefore, the inlet pressure into the reducing bend is 1.8 x [tex]10^6[/tex] Pa, the total force in the X and Y directions are 2.638 x [tex]10^5[/tex] N and 294.3 N, respectively, the pressure force in the X and Y directions are 4243.4 N and 9.81 N, respectively, and the anchoring force needed to hold the elbow in place is 4249.5 N.
Learn more on pressure on https://brainly.com/question/24719118
#SPJ4
A rhombus has side lengths of 30 inches and the longest diagonal is 45 inches. Determine the measure of the larger congruent angles. Round to the nearest tenth of a degree.
The measure of the larger congruent angles in the rhombus is approximately 134.3 degrees.
In a rhombus, all four sides are equal in length, and the diagonals bisect each other at right angles. To determine the measure of the larger congruent angles, we can use the properties of a rhombus and apply the trigonometric concept of the Law of Cosines.
Let's denote the measure of the larger congruent angle as θ. In a rhombus, the diagonals are perpendicular bisectors of each other, forming four congruent right triangles. The sides of each right triangle are half the length of the diagonals.
Using the Law of Cosines, we can relate the side lengths and diagonal lengths:
[tex]c^{2} = a^{2} + b^{2} - 2ab * cos(θ)[/tex]
Given that the side length (a) is 30 inches and the longest diagonal (c) is 45 inches, we can substitute these values into the equation:
[tex]45^{2} = 30^{2} + 30^{2} - 2(30)(30) * cos(θ)[/tex]
2025 = 900 + 900 - 1800 * cos(θ)
225 = -1800 * cos(θ)
cos(θ) = -225/1800
θ = [tex]cos^{(-1)(-225/1800)}[/tex]
Using a calculator, we find θ ≈ 134.3 degrees (rounded to the nearest tenth of a degree).
Know more about Law of cosines here:
https://brainly.com/question/30766161
#SPJ8
The integers 297,595 , and 2912 are pairwise relatively prime. True False
The integers 297, 595, and 2912 are NOT pairwise relatively prime. The answer is False.
Let's first define what pairwise relatively prime is. Two or more numbers are considered pairwise relatively prime if there is no common factor (other than 1) between them. For instance, 2 and 3 are pairwise relatively prime.
However, 4 and 6 are not, because they share a common factor of 2.
Thus, to determine if the integers 297, 595, and 2912 are pairwise relatively prime or not, we need to compute the greatest common divisor (GCD) for all possible pairs of numbers.
If the GCD is 1 for all pairs, then the integers are pairwise relatively prime.
So we can do it as follows:
For 297 and 595, GCD(297, 595) = 33
For 297 and 2912, GCD(297, 2912) = 33
For 595 and 2912, GCD(595, 2912) = 17
Therefore, since not all pairs have a GCD of 1, the integers 297, 595, and 2912 are NOT pairwise relatively prime.
The answer is False.
Learn more about prime
https://brainly.com/question/4184435
#SPJ11
"The integers 297,595, and 2912 are pairwise relatively prime" is false.
Two integers are considered pairwise relatively prime if their greatest common divisor (GCD) is equal to 1. In this case, we need to check the GCD between each pair of the given integers.
To find the GCD between two numbers, we can use the Euclidean algorithm.
The GCD of 297 and 595 is 1, which means they are relatively prime.
However, the GCD of 595 and 2912 is not equal to 1. By applying the Euclidean algorithm, we find that the GCD is 17. Therefore, 595 and 2912 are not relatively prime.
Since 595 and 2912 are not relatively prime, the statement is false.
Learn more about prime
https://brainly.com/question/34250415
#SPJ11
Jackson deposits 1150 at the end of each month in a savings account earning interest at a rate of 9%/year compounded monthly, how much will he have on deposit in his savings account at the end of years, assuming he makes no withdrawals during that period? (Round your answer to the nearest cent
Jackson will have approximately $2748.17 on deposit in his savings account at the end of 150 months.
To calculate the amount that Jackson will have on deposit in his savings account at the end of 150 months, we can use the formula for compound interest:
[tex]A = P(1 + r/n)^(nt)[/tex]
Where:
A = the amount on deposit at the end of the time period
P = the principal amount (the initial deposit)
r = the annual interest rate (as a decimal)
n = the number of times the interest is compounded per year
t = the number of years
In this case, Jackson deposits $1150 at the end of each month, so the principal amount (P) is $1150. The annual interest rate (r) is 9% or 0.09 as a decimal.
The interest is compounded monthly, so the number of times compounded per year (n) is 12.
And the time period (t) is 150 months divided by 12 to convert it to years.
Plugging these values into the formula:
[tex]A = 1150(1 + 0.09/12)^(12*(150/12))[/tex]
Simplifying:
[tex]A = 1150(1 + 0.0075)^(12*12.5)[/tex]
[tex]A = 1150(1.0075)^(150)[/tex]
Using a calculator, we can find that [tex](1.0075)^(150)[/tex] is approximately 2.3861.
A ≈ 1150 * 2.3861
A ≈ 2748.165
Rounding the answer to the nearest cent, Jackson will have approximately $2748.17 on deposit in his savings account at the end of 150 months.
Learn more about savings account from this link:
https://brainly.com/question/30101466
#SPJ11
In mass balance experiment, the following data were collected: The mass of peanut before drying is 28.42 g The mass of peanut after drying is 27.8 g The mass of crushed peanut is 27.35 g The volume of hexane is 250 ml The volume of recovered hexane from distillation process is 220 ml. The mass of wet spent peanut is 34.675 g The mass of dry spent peanut is 18.3 g Density of hexane is 655 kg/m³ Perform the detail calculation and then fill the followings: a) Amount of water = g b) % water = c) Amount of loss from crushing process = g d) % loss from crushing process = e) Amount of oil extracted = g f) % Oil recovery from peanut before drying = g) % solvent recovery from distillation process = h) Total solvent recovered from distillation and evaporation processes = i) Solvent make up = g j) % of solvent make up related to total solvent in the process ml
a) The amount of water in the peanut is 0.62 g.
b) The percentage of water in the peanut is 2.18%.
c) The amount of loss from the crushing process is 0.47 g.
d) The percentage of loss from the crushing process is 1.66%.
e) The amount of oil extracted from the peanut is 9.12 g.
f) The percentage of oil recovery from the peanut before drying is 32.09%.
g) The percentage of solvent recovery from the distillation process is 88%.
h) The total solvent recovered from the distillation and evaporation processes is 215 ml.
i) The amount of solvent makeup is 35 ml.
j) The percentage of solvent makeup related to the total solvent in the process is 14.63%.
To calculate the values, we'll use the given data and perform the necessary calculations:
a) The amount of water can be obtained by subtracting the mass of the peanut after drying from the mass of the peanut before drying:
28.42 g - 27.8 g = 0.62 g.
b) The percentage of water can be calculated by dividing the amount of water by the mass of the peanut before drying and multiplying by 100: [tex]\[\left(\frac{0.62 \, \text{g}}{28.42 \, \text{g}}\right) \times 100 = 2.18\%.\][/tex]
c) The amount of loss from the crushing process can be calculated by subtracting the mass of the crushed peanut from the mass of the peanut before drying:
28.42 g - 27.35 g = 0.47 g.
d) The percentage of loss from the crushing process can be calculated by dividing the amount of loss from the crushing process by the mass of the peanut before drying and multiplying by 100:
[tex]\[\left(\frac{0.47 \, \text{g}}{28.42 \, \text{g}}\right) \times 100 = 1.66\%.\][/tex]
e) The amount of oil extracted can be calculated by subtracting the mass of the dry spent peanut from the mass of the wet spent peanut:
34.675 g - 18.3 g = 9.375 g.
f) The percentage of oil recovery from the peanut before drying can be calculated by dividing the amount of oil extracted by the mass of the peanut before drying and multiplying by 100:
[tex]\[ \left(\frac{9.375 \, \text{g}}{28.42 \, \text{g}}\right) \times 100 = 32.09\% \][/tex]
g) The percentage of solvent recovery from the distillation process can be calculated by dividing the volume of recovered hexane from distillation by the volume of hexane used and multiplying by 100:
[tex]\[ \left(\frac{220 \, \text{ml}}{250 \, \text{ml}}\right) \times 100 = 88\% \][/tex]
h) The total solvent recovered from the distillation and evaporation processes is given as 220 ml.
i) The amount of solvent makeup is given as 35 ml.
j) The percentage of solvent makeup related to the total solvent in the process can be calculated by dividing the amount of solvent makeup by the total solvent recovered and multiplying by 100:
[tex]\[ \left(\frac{35 \, \text{ml}}{215 \, \text{ml}}\right) \times 100 = 16.28\% \][/tex]
The calculations above provide the values for each parameter as requested in the question.
To know more about Calculate visit-
brainly.com/question/31718487
#SPJ11
Solve the given initial value problem.
y''+5y'=0; y(0)=3, y'(0)=-25
The solution is y(t)= ?
The solution to the given initial value problem (y'' + 5y' = 0), with (y(0) = 3) and (y'(0) = -25), is: (y(t) = -2 + 5e^{-5t}).
An initial value problem (IVP) is a type of mathematical problem that involves finding a solution to a differential equation or a difference equation along with an initial condition.
To solve the given initial value problem (y'' + 5y' = 0), with the initial conditions (y(0) = 3) and (y'(0) = -25), we can use the method of solving linear second-order homogeneous differential equations.
Step 1: Find the characteristic equation by assuming (y(t) = e^{rt}), where (r) is a constant.
The characteristic equation is (r^2 + 5r = 0).
Step 2: Solve the characteristic equation to find the values of (r).
Factoring out (r), we get (r(r + 5) = 0).
So, the values of (r) are (r = 0) and (r = -5).
Step 3: Write down the general solution.
Since we have two distinct real roots, the general solution is given by:
[y(t) = c_1e^{0t} + c_2e^{-5t}], where (c_1) and (c_2) are arbitrary constants.
Simplifying this expression, we get:
[y(t) = c_1 + c_2e^{-5t}].
Step 4: Use the initial conditions to find the values of the constants (c_1) and (c_2).
Given (y(0) = 3), we substitute (t = 0) into the general solution:
[3 = c_1 + c_2e^{0} = c_1 + c_2].
Given (y'(0) = -25), we take the derivative of the general solution and substitute (t = 0):
[y'(t) = -5c_2e^{-5t}].
[-25 = -5c_2e^{0} = -5c_2].
Simplifying these equations, we find (c_1 = 3 - c_2) and (c_2 = 5).
Step 5: Substitute the values of (c_1) and (c_2) into the general solution.
Using (c_1 = 3 - c_2 = 3 - 5 = -2), we have:
[y(t) = -2 + 5e^{-5t}].
Therefore, the solution to the given initial value problem (y'' + 5y' = 0), with (y(0) = 3) and (y'(0) = -25), is: (y(t) = -2 + 5e^{-5t}).
Learn more about initial value problem:
https://brainly.com/question/31041139
#SPJ11
Calculate the pH and the concentrations of all species present in 0.11MH_2SO_3⋅(K_a1=1.5×10^−2,K_a2=6.3×10^−8).Express your answer to three significant figures and include the appropriate units.
Therefore, the pH and concentrations of all species present in 0.11 M H2SO3 are:
pH = 1.22
[H2SO3] = 0.050 M
[HSO3-] = 0.060 M
[SO3^2-] = 0.060 M
To calculate the pH and the concentrations of all species present in 0.11 M H2SO3, we can set up the following equations:
H2SO3 <=> H+ + HSO3-
HSO3- <=> H+ + SO3^2-
The ionization constants (Ka values) for these equations are given as:
Ka1 = 1.5 x 10^-2
Ka2 = 6.3 x 10^-8
Given: Concentration of H2SO3 = 0.11 M
First ionization equation:
Ka1 = [H+][HSO3-] / [H2SO3]
Let the concentration of [H+] be 'x'. Therefore, the concentration of [HSO3-] is equal to (0.11 - x).
Using the above equation and Ka1 value, we get:
1.5 x 10^-2 = (x * (0.11 - x)) / 0.11
Solving the quadratic equation, we find x = 0.060 M.
Hence, the pH of H2SO3 is:
pH = -log[H+]
= -log(0.060)
= 1.22
Now, to find the concentrations of all species, we use an equilibrium table:
Equilibrium Table:
Species H2SO3 HSO3- SO3^2-
Initial Conc. 0.11 M 0 M 0 M
Change (-x) (+x) (+x)
Equilibrium Conc.0.11-x x x
We have found the value of x to be 0.060 M.
So, the equilibrium concentration of HSO3- and SO3^2- will be 0.060 M and 0.060 M, respectively.
The equilibrium concentration of H2SO3 will be (0.11 - x), which is 0.11 - 0.060 = 0.050 M.
Learn more about pH from the given link:
https://brainly.com/question/12609985
#SPJ11
An acute triangle has sides measuring 10 cm and 16 cm. The length of the third side is unknown.
Which best describes the range of possible values for the third side of the triangle?
x < 12.5, x > 18.9
12.5 < x < 18.9
x < 6, x > 26
6 < x < 26
Answer:
6 < x < 26
Step-by-step explanation:
given 2 sides of a triangle then the third side x is in the range
difference of 2 sides < x < sum of 2 sides , then
16 - 10 < x < 16 + 10 , that is
6 < x < 26
State the null (H0) and alternative (H1) hypothesis for this ANOVA test and indicate the degrees of freedom for errors (v1 and v2), that should be used to conduct the test (using the F-Distribution) if testing at the 5% level of significance.
The null hypothesis (H0) for this ANOVA test is that there is no significant difference among the means of the groups being compared. The alternative hypothesis (H1) is that there is a significant difference among the means of the groups.
The degrees of freedom for errors (v1 and v2) in this ANOVA test should be (k - 1) and (N - k), respectively, where k is the number of groups being compared and N is the total number of observations.In an ANOVA (Analysis of Variance) test, the null hypothesis (H0) states that there is no significant difference among the means of the groups being compared. This means that any observed differences in means are due to random variation or chance.
The alternative hypothesis (H1), on the other hand, asserts that there is a significant difference among the means of the groups. It suggests that the observed differences are not due to chance and that there are actual differences between the groups.
To conduct the ANOVA test, we need to determine the degrees of freedom for errors (v1 and v2). The degrees of freedom for errors represent the variability within the data and are used to calculate the critical value from the F-distribution. The formula for calculating the degrees of freedom for errors in an ANOVA test is (k - 1) and (N - k), where k is the number of groups being compared and N is the total number of observations.
For example, if we are comparing the means of three groups and we have a total of 30 observations, the degrees of freedom for errors would be (3 - 1) and (30 - 3), which are 2 and 27, respectively.
To conduct the test at the 5% level of significance, we would compare the calculated F-value to the critical F-value obtained from the F-distribution with the appropriate degrees of freedom.
Learn more about Hypothesis
brainly.com/question/32562440
#SPJ11
1) Solve the following
a) The reaction of 3A ⟶B + 2C is found to have a 72.2% yield. How many moles of A are needed in order to create 1.167 mol of C?
Report your answer to three decimal places.
b) For the decomposition reaction:
X(s) ⟶Y(g) + Z(s)
A student runs the reaction with a given amount of reactant X, and she calculates the theoretical yield to be 47.3 g of product Z. If there are 0.5 mol of Z present after the reaction is complete, what is the % yield of this reaction? Assume Z has a molar mass of 82 g/mol. Report your answer to two decimal places.
c)
A student is performing a multistep reaction to synthesize an organic compound, shown below in a simplified form:
2A ⟶5B
B ⟶2C
3C ⟶ D
The reactant A has a molar mass of 147.1 g/mol and the final product D has a molar mass of 135 g/mol. Assuming that each step has 100% yield, what final mass of D should be created if the student reacts 72 g of reactant A? Report your answer with one decimal place.
The number of moles of A required to form 1.167 mol of C is 1.751 mol. The % yield of the reaction is 86.60%. The final mass of D formed by reacting 72 g of reactant A is 33.0 g.
For the given chemical reaction 3A ⟶ B + 2C, 72.2% yield is given.
We need to find out the number of moles of A required to form 1.167 mol of C.
Yield = 72.2% = 0.722
Moles of C formed = 1.167 mol
The balanced chemical reaction is,3A ⟶ B + 2C
Total moles of product formed = moles of B + moles of C
= (1/1)mol + (2/1) mol
= 3 mol
Moles of A required to form 1 mol of C = 3/2 mol
Moles of A required to form 1.167 mol of C = (3/2) × 1.167 mol
= 1.7505 mol
≈ 1.751 mol
Therefore, the number of moles of A required to form 1.167 mol of C is 1.751 mol.
Reported answer = 1.751 (to three decimal places).
For the given reaction X(s) ⟶ Y(g) + Z(s), theoretical yield of Z = 47.3 g
Molar mass of Z = 82 g/mol
Moles of Z present after the reaction is complete = 0.5 mol
Let the actual yield be y.
The balanced chemical reaction is,X(s) ⟶ Y(g) + Z(s)
The number of moles of Z produced per mole of X reacted = 1
Therefore, moles of Z produced when moles of X reacted = 0.5 mol
Molar mass of Z = 82 g/mol
Mass of Z produced when moles of X reacted = 0.5 × 82 g
= 41 g
% Yield = (Actual yield ÷ Theoretical yield) × 100
%Actual yield, y = 41 g
% Yield = (41 ÷ 47.3) × 100%
= 86.59%
≈ 86.60%
Therefore, the % yield of the reaction is 86.60%.
Given the reaction:2A ⟶5B
(Step 1)B ⟶2C
(Step 2)3C ⟶D
(Step 3)Molar mass of A = 147.1 g/mol
Molar mass of D = 135 g/mol
Mass of A = 72 g
Number of moles of A = (72 g) ÷ (147.1 g/mol)
= 0.489 mol
According to the chemical reaction,2 mol of A produces 1 mol of D
∴ 1 mol of A produces 1/2 mol of D
Therefore, 0.489 mol of A produces = (1/2) × 0.489 mol of D
= 0.2445 mol of D
Molar mass of D = 135 g/mol
Mass of D produced = 0.2445 mol × 135 g/mol
= 33.023 g
≈ 33.0 g
Therefore, the final mass of D that is created when 72 g of reactant A is reacted is 33.0 g (reported with one decimal place).
In the first part, we have to determine the number of moles of A required to form 1.167 mol of C. This can be calculated by determining the number of moles of B and C formed and then using the stoichiometry of the reaction to determine the number of moles of A used. In the second part, we have to determine the % yield of the reaction using the actual and theoretical yield of the reaction. In the third part, we have to determine the final mass of D formed by reacting 72 g of reactant A using the stoichiometry of the reaction. The three given problems are solved with the help of balanced chemical reactions, stoichiometry, and percentage yield of the reaction.
The number of moles of A required to form 1.167 mol of C is 1.751 mol. The % yield of the reaction is 86.60%. The final mass of D formed by reacting 72 g of reactant A is 33.0 g.
To know more about number visit:
brainly.com/question/3589540
#SPJ11
Determine the power output of a cylinder having a cross-sectional area of A square inches, a length of stroke L inches, and a mep of p_{m}p m psi, and making N power strokes per minute.4
The power output of the cylinder is given by the expression: Power = (mep × A × L) × N
The power output of a cylinder can be calculated using the formula:
Power = (Force × Distance) ÷ Time
In this case, the force exerted by the cylinder is the mean effective pressure (mep) multiplied by the cross-sectional area of the cylinder. The distance is the length of stroke, and the time is the time taken for N power strokes per minute.
Given:
Cross-sectional area of the cylinder (A) = A square inches
Length of stroke (L) = L inches
Mean effective pressure (mep) = p_m psi
Number of power strokes per minute (N) = N
The force exerted by the cylinder is:
Force = mep × A
The distance covered by the piston in one stroke is L inches.
The time taken for N power strokes per minute is:
Time = 1 minute / N
Substituting these values into the power formula, we get:
Power = (mep × A × L) ÷ (1 minute / N)
Simplifying further, we have:
Power = (mep × A × L) × N
Therefore, the power output of the cylinder is given by the expression:
Power = (mep × A × L) × N
To know more about power output visit :
https://brainly.com/question/21208683
#SPJ11
Solve the equation g(x)=1 for x if g(x)=-0.3 x^{2}+3 x+6 . x= (Use a comma to separate solutions. Round to four decimal places.)
The solution to the equation g(x) = 1 for x is [tex]x = 11.4586, -1.4586[/tex] Given equation g(x) = -0.3 x² + 3x + 6. We need to solve the equation g(x) = 1 for x.
So, we get,
-0.3 [tex]x² + 3x + 6 = 1[/tex]
Adding -1 on both sides of the equation, we get,-0.[tex]3 x² + 3x + 5 = 0.[/tex] Multiplying the entire equation by -10, we get,
3x² - 30x - 50 = 0
Dividing the entire equation by 3, we get,
[tex]x² - 10x - 16.66667 = 0[/tex]
Now, we can solve this quadratic equation using the quadratic formula, which is given by,
[tex]x = (-b ± √(b² - 4ac)) / (2a).[/tex]
Here, a = 1, b = -10, and c = -16.66667.Substituting these values in the formula, we get,
x = [10 ± √(100 - 4×1×(-16.66667))] / (2×1)x
= [10 ± √(100 + 66.66668)] / 2x
= [10 ± √(166.66668)] / 2x
= [10 ± 12.91728] / 2x
= 11.45864, -1.45864
Rounded off to four decimal places, the solutions are 11.4586 and -1.4586.
To know more about sides visit:
https://brainly.com/question/31139338
#SPJ11
Shear and Moment Diagram 1. Find the maximum shear and moment values by using the Shear and Moment Diagram. The section of the rectangular beam has a width of 250 mm and a depth of 400 mm. What is the maximum flexural stress of the beam' 25 KN 20 KN/m 15 KN 20 KN/m 10 KN B D E F Ak tamme 2 m 2 m 2 m 4 m 2 m RA RE
The maximum flexural stress of the rectangular beam can be determined by analyzing the shear and moment diagram and finding the maximum shear and moment values.
Analyze the Shear and Moment Diagram
To find the maximum shear and moment values, we need to analyze the shear and moment diagram for the rectangular beam. The shear diagram represents the variation of shear forces along the length of the beam, while the moment diagram represents the variation of bending moments. By examining these diagrams, we can identify the maximum values.
Identify Maximum Shear and Moment Values
In the shear diagram, the maximum shear value occurs at the point where the shear force is highest. Similarly, in the moment diagram, the maximum moment value occurs at the point where the bending moment is highest. By locating these points on the diagrams, we can determine the maximum shear and moment values.
Calculate Maximum Flexural Stress
Once we have obtained the maximum shear and moment values, we can calculate the maximum flexural stress using the formula:
Flexural Stress = (Maximum Moment) * (Distance from Neutral Axis) / (Moment of Inertia)
The distance from the neutral axis can be determined based on the dimensions of the rectangular beam (width and depth). The moment of inertia depends on the cross-sectional shape of the beam and can be calculated using standard formulas.
By substituting the values into the formula, we can find the maximum flexural stress of the beam.
Learn more about moment values
brainly.com/question/32354951
#SPJ11
Imagine 100 individuals are asked to take part in a replication of Milgram's famous study on obedience. How are these 100 people likely to respond? The majority would administer 450 volts as instructed, The majority would immediately realize the use of deception and leave. Most of the women would refuse to obey, whereas all of the men would obey. O Most of the participants would work together to force the experimenter to end the experiment and create a new experiment.
In a replication of Milgram's famous study on obedience with 100 individuals, it is likely that the majority would administer 450 volts as instructed.
Milgram's study on obedience involved participants administering electric shocks to a learner in a simulated learning task. The study found that a significant majority of participants obeyed the experimenter's instructions and administered the maximum 450 volts, despite the potential harm to the learner. This suggests that under certain circumstances, individuals are willing to obey authority figures, even if it goes against their own moral beliefs.
The study demonstrated the power of situational factors in influencing human behavior and highlighted the importance of ethical considerations in research. While not all individuals may necessarily obey in a replication of the study, it is likely that a majority would still comply with the instructions given.
Know more about moral beliefs here:
https://brainly.com/question/33776125
#SPJ11