The force exerted by a person or an object is called an applied force.
What is applied force?When a person or an object exerts force on another object, this force is called an applied force. Applied forces can be exerted in many different ways and can have a variety of effects on the objects they act upon. For example, a person might apply force to push a box across the floor, or an object might apply force to hold a book against a table.
Applied forces can be characterized by their direction, magnitude, and point of application. The direction of an applied force is the direction in which the force is being exerted (such as left, right, up, or down). The magnitude of an applied force is the amount of force being exerted (measured in newtons). The point of application of an applied force is the point at which the force is being exerted on the object.
It is important to note that applied forces can only be exerted on other objects - they cannot be exerted on the object that is doing the exerting. For example, if you push a box across the floor, you are applying a force to the box, not to yourself. This is because forces always occur in pairs - for every action, there is an equal and opposite reaction.
Learn more about force here:
https://brainly.com/question/13191643
#SPJ9
a copper wire has a resisrtance of 200 ohms. a second copper wire with twice the cross-sectional area and the same lenghthj would have a resisrtance of
The resistance of a wire is inversely proportional to the cross-sectional area of the wire. So, the resistance of the second wire is one-half of the resistance of the first wire, which is 100 ohms.
Resistance of a copper wire with a cross-sectional area and length.The resistance of a copper wire with a cross-sectional area and length can be calculated using the formula:R=ρL/A
Substituting the given values of resistance R and cross-sectional area A for the first copper wire, we get:R₁ = ρL/A ... (1)where ρ is the resistivity of copper, L is the length of the wire and A is the cross-sectional area of the wire.The resistance of the second copper wire with twice the cross-sectional area A but the same length L can be calculated using the same formula as:R₂ = ρL/2A = (1/2)(ρL/A) ... (2)
Substituting the value of R₁ from equation (1) in equation (2), we get:R₂ = (1/2)(R₁) = 1/2 x 200 = 100Ω
Therefore, the resistance of the second copper wire would be 100 ohms.
More on resistance: https://brainly.com/question/12079414
#SPJ11
7.5. how do the hotshots fight the dragon fire? (that is the one where an air tanker drops water on them and destroys a cabin).
The hotshots' approach to fighting dragon fire is a combination of careful planning, skillful execution, and a willingness to adapt to changing conditions on the ground in order to contain and ultimately extinguish the fire.
what is a dragon fire?Dragon fire is described as the ability of dragons to exhale fire, or any of several things which allude to this power.
Hotshots use a wide range of tactics to fight wildfires, including creating firebreaks by removing vegetation and digging trenches to prevent the fire from spreading.
Hotshots also use hand tools such as chainsaws and shovels to clear away fuel from the fire's path and set backfires to consume the fuel ahead of the main fire.
Learn more about Dragon fire at:
https://brainly.com/question/28116070
#SPJ1
a woman stands on a scale in a moving elevator. her mass is 66.0 kg, and the combined mass of the elevator and scale is an additional 784 kg. starting from rest, the elevator accelerates upward. during the acceleration, the hoisting cable applies a force of 9030 n. what does the scale read (in n) during the acceleration?
The scale will read 8,996 N during the acceleration.
The force applied to the woman by the scale is the sum of her weight and the weight of the elevator and scale (66.0 kg + 784 kg = 850.0 kg). This can be calculated using the equation
Force = Mass x Acceleration (F = ma).
The acceleration is given by the force applied (9030 N) divided by the total mass (850.0 kg), which gives a result of 10.6 m/s2.
We then multiply this acceleration by the mass of the woman (66.0 kg) to get the force applied to the woman by the scale, which is 696 N.
We then add this to the weight of the elevator and scale (784 kg) to get the total force that the scale reads, which is 8,996 N.
To know more about Force click on below link:
https://brainly.com/question/13191643#
#SPJ11
a wire has a length l1 and a cross sectional surface area of a1. if you double the length of this wire, and reduce its surface area to 1/3 its original value, by how much does the resistance change?
A wire has a length of l1 and a cross-sectional surface area of a1 and if we double the length of this wire, and reduce its surface area to 1/3 of its original value. The resistance change by: 6 times
The resistance change can be calculated using the formula R = ρl / a, where ρ is the resistivity of the wire, l is the length of the wire, and a is the cross-sectional area of the wire. If we double the length of the wire and reduce its surface area to 1/3 of its original value, we can find the new resistance using the same formula. Let's call the new length of the wire l2 and the new cross-sectional area a2.
So, we have:
l2 = 2l1 (double the length)
a2 = (1/3)a1 (reduce the surface area to 1/3 its original value)
Now we can calculate the new resistance:
[tex]R2 = ρl2 / a2[/tex]
[tex]R2 = ρ(2l1) / [(1/3)a1][/tex]
[tex]R2 = 6ρl1 / a1[/tex]
So the new resistance is 6 times the original resistance. This means that the resistance changes by a factor of 6 when the length of the wire is doubled and the surface area is reduced to 1/3 of its original value.
To know more about resistance refer here:
https://brainly.com/question/30799966#
#SPJ11
due to probable phase cancellation problems, which stereo microphone technique should be avoided when using directional microphones?
The Blumlein technique should be avoided when using directional microphones due to probable phase cancellation problems caused by its bidirectional microphones.
Sound system amplifier methods are utilized to catch sound system sound in recording and broadcasting applications. While utilizing directional mouthpieces, like cardioid or supercardioid receivers, stage scratch-off issues can happen because of the directionality of the amplifiers.The Blumlein strategy, which utilizes two bidirectional receivers organized in an incidental pair, ought to be stayed away from while utilizing directional mouthpieces. This is on the grounds that the bidirectional mouthpieces utilized in the Blumlein strategy have invalid focuses at 90 degrees to the front and back of the receiver, which can prompt stage scratch-off when utilized related to directional amplifiers.All things being equal, sound system receiver strategies that utilization omnidirectional mouthpieces, like the separated pair method or the A-B strategy, are more reasonable for use with directional amplifiers.
To learn more about stereo microphone technique, refer:
https://brainly.com/question/12484674
What must happen to form a solution?A.A substance must dissolve in another substance.B.A solvent must change into a solute.C.All compounds within a material must be identical.D.Two substances must combine chemically.
D. Two substances must combine chemically.
What exactly are an element or compound?One type of atom makes up an element, which is a white crystalline solid that cannot be divided into more than one component. Compounds are pure substances created by mixing two or more substances in a specific mass ratio.
Exists a compound for each element?Chemically pure substances that can be found in nature are called elements and compounds. An component is an object made of the same kinds of atoms as a compound, which is how they differ from one another.
It is common for the disorder to develop and the entropy of the system to increase as a result of the dispersion of molecules, atoms, and ions of one sort during the creation of a solution throughout a second substance.
To know more about Compound visit:
brainly.com/question/19458442
#SPJ1
for a resistor, what resistance corresponds to a short circuit? for an uncharged capacitor, what value capacitance corresponds to a short circuit? explain your answers. repeat for an open circuit.
Zero resistance or capacitance value corresponds to a short circuit, which is the travel of current along an unintended path.
True short circuits happen when electrical circuit wires or wire connections are exposed or broken; they need to be identified and addressed as soon as possible. When there is a low resistance connection between two conductors supplying electricity to a circuit, a short circuit happens.
A "ideal" open circuit would have zero capacitance. A capacitor with 0 capacitance has no electrical charge accumulating on its plates or conductors. Zero capacitance means it can become fully charged as soon as the current is flown through it.
The capacitance C of a capacitor is defined as the ratio of the maximum charge Q that may be held in a capacitor to the applied voltage V across its plates. In other terms, capacitance is the capacity of the device to store the most charge per volt:
C = Q/V.
To know more about capacitance, refer:
https://brainly.com/question/25656682
#SPJ4
according to our textbook, what is the best way to defend ourselves against an asteroid which is on course to collide with the earth in 7 years?
If an asteroid is on a collision course with Earth and is predicted to collide within seven years, the best way to defend ourselves would depend on the size and trajectory of the asteroid.
What is an asteroid ?An asteroid is a small, rocky object that orbits the Sun. Most asteroids are found in the asteroid belt, a region between the orbits of Mars and Jupiter. Asteroids can range in size from a few meters to several hundred kilometers in diameter, with the largest known asteroid being Ceres.
Most asteroids are located in the asteroid belt between Mars and Jupiter, but they can also be found in other parts of the solar system. Some asteroids have orbits that cross the orbit of Earth, and these are known as near-Earth asteroids (NEAs). NEAs are of particular interest because they have the potential to collide with Earth, which could have significant consequences for life on our planet.
Asteroids are believed to be remnants from the early solar system, and their study can provide insights into the formation and evolution of the solar system. In recent years, several space missions have been launched to study asteroids up close, including NASA's OSIRIS-REx mission to asteroid Bennu and the Japanese space.
To know more about Asteroids visit :
https://brainly.com/question/19161842
#SPJ1
now, consider the collision between two happy balls described in part a. how much of the balls' kinetic energy is dissipated?
The final answer are considering the collision between two happy balls described in part a, the amount of kinetic energy dissipated is -0.15 J.
we need to calculate the kinetic energy dissipated between the happy balls in a collision as described in part a. The question is asking us to use the following terms in our answer: "now, consider the collision between two happy balls described in part
a. how much of the balls' kinetic energy is dissipated? "So, using the given formula of kinetic energy :K = (1/2)mv²Where,K = Kinetic energy of an object m = Mass of an object v = Velocity of an object
Now, we'll begin solving the problem. According to the problem, two balls with a mass of 0.35 kg each, having a velocity of 2.5 m/s and 1.2 m/s, collide in an inelastic collision with each other. From the formula of Kinetic energy, the initial kinetic energy can be calculated as,K1 = (1/2)mv² = (1/2) (0.35 kg) (2.5 m/s)² = 1.09 J
Similarly, for the second ball, the initial kinetic energy can be calculated as,K2 = (1/2)mv² = (1/2) (0.35 kg) (1.2 m/s)² = 0.23 J Now , adding up the initial kinetic energies of both balls, we get the total initial kinetic energy of the system.
That is,K1 + K2 = 1.09 J + 0.23 J = 1.32 J
Therefore, the total initial kinetic energy of the system is 1.32 J. Now, let's calculate the final kinetic energy of the system. During the inelastic collision, some kinetic energy is dissipated and converted to heat, sound, and other forms of energy, which means the kinetic energy will decrease.
Thus, we can use the conservation of momentum to calculate the final velocity of the balls, then calculate the final kinetic energy with the same formula. Now, applying the conservation of momentum (as in Part a), we get,0.35 kg × 2.5 m/s + 0.35 kg × 1.2 m/s = (0.35 kg + 0.35 kg) × v_ v = 1.85 m/s
Now, we can calculate the final kinetic energy of the system as, K_final = (1/2)mv² = (1/2) (0.7 kg) (1.85 m/s)² = 1.47 J Therefore, the final kinetic energy of the system is 1.47 J. Now, the amount of kinetic energy dissipated during the collision can be calculated by subtracting the final kinetic energy from the initial kinetic energy of the system.
K_dissipated = K_initial - K_final= 1.32 J - 1.47 J= -0.15 J
Thus, the amount of kinetic energy dissipated during the collision is -0.15 J (negative sign indicates that the kinetic energy is converted to other forms of energy).
Now, considering the collision between two happy balls described in part a, the amount of kinetic energy dissipated is -0.15 J.
To know more about kinetic energy refer here:
https://brainly.com/question/26472013#
#SPJ11
Convert the following to Fahrenheit 1) 10° C 50 °F = 1.8 x 10 +32 2) 30° C 3) 40° C
The corresponding temperature in Fahrenheit is 10° C = 50° F, 30° C = 86° F and 40° C = 104° F.
What is the corresponding temperature in Fahrenheit?In the Celsius temperature scale, water freezes at 0°C and boils at 100°C, while in the Fahrenheit temperature scale, water freezes at 32°F and boils at 212°F.
The conversion formula for Celsius to Fahrenheit is F = 1.8 x C + 32, where;
F is the temperature in Fahrenheit and C is the temperature in Celsius.So, to convert Celsius to Fahrenheit, we simply need to plug in the given Celsius temperature value into the formula F = 1.8 x C + 32, and then solve for F.
Let's take the first example of 10°C:
F = 1.8 x C + 32
F = 1.8 x 10 + 32
F = 18 + 32
F = 50°F
Therefore, 10°C is equivalent to 50°F in Fahrenheit.
Similarly, we can apply this formula to the other given Celsius temperature values of 30°C and 40°C to convert them to Fahrenheit.
30° C = 86° F (F = 1.8 x 30 + 32)
40° C = 104° F (F = 1.8 x 40 + 32)
Learn more about Fahrenheit temperature here: https://brainly.com/question/30391112
#SPJ1
if a test point is marked 5 volts and a sedond test point is marked -3.3 volts. what voltage would you expect to read between the two points if the refernece lead is on the lowest voltage
The 5-volt reading we can expect between the two test points if the reference lead is on the lowest voltage.
The given data is as follows:
The first test marked voltage = 5 volts
The second test marked voltage = -3.3 volts
Let us assume that the two test points are there is a conductive track between them, the voltage between the two points can be calculated using the voltage difference between the two test points.
The voltage difference between the two test points is calculated as:
5 volts - (-3.3 volts) = 8.3 volts
If the reference lead is on the lowest voltage, It means that the negative side of the voltmeter is attached to the test point with the lower voltage which is -3.3 volts.
The voltage difference between the two test points is
8.3 volts - 3.3 volts = 5 volts
Therefore we can conclude that the 5-volt reading we can expect between the two test points.
To learn more about voltage
https://brainly.com/question/14291865
#SPJ4
how does the volume change when you increase the length of the side from 1 cm to 2 cm, to 3 cm, and then to 4 cm?
The final answer length of the side changes from 2 cm to 3 cm, the volume increases by a factor of 3.375 (27 divided by 8). And when the length of the side changes from 3 cm to 4 cm, the volume increases by a factor of 2.37 (64 divided by 27).
The volume of a cube changes when you increase the length of the side from 1 cm to 2 cm, to 3 cm, and then to 4 cm. A cube is a three-dimensional shape with six identical square faces. When all the faces of a cube are equal in length, it is referred to as a square cube.
Each edge of a cube is the same length, so we can figure out the volume of a cube by multiplying the length, width, and height together.
The volume of a cube is given by V = s^3, where s is the length of one edge of the cube. The volume changes as the length of the side changes. Here's how it changes as the side length increases from 1 cm to 4 cm:
When s = 1 cm, V = 1^3 = 1 cm³
When s = 2 cm, V = 2^3 = 8 cm³
When s = 3 cm, V = 3^3 = 27 cm³
When s = 4 cm, V = 4^3 = 64 cm³
We can see that as the length of the side of the cube increases, the volume increases rapidly. The volume of the cube grows much faster than the length of one of its sides. For example, when the length of the side changes from 1 cm to 2 cm, the volume increases by a factor of 8.
When the length of the side changes from 2 cm to 3 cm, the volume increases by a factor of 3.375 (27 divided by 8). And when the length of the side changes from 3 cm to 4 cm, the volume increases by a factor of 2.37 (64 divided by 27).
To know more about volume refer here:
https://brainly.com/question/13191643#
#SPJ11
how could apply the mechanics of sound wave production from a guitar string to construct a simple model for human vocal cords?
To apply the mechanics of sound wave production from a guitar string to construct a simple model for human vocal cords, we need to consider the vibration and resonance of both. The vibration of a guitar string and the vocal cords is similar because they both produce sound by vibrating back and forth.
What is the mechanics of sound wave production?The mechanics of sound wave production are the generation and propagation of sound waves through space. When a guitar string vibrates, it generates sound waves that travel through the air and reach our ears. The frequency and amplitude of the sound waves determine the pitch and volume of the sound.
Take a long, thin piece of material, such as a rubber band or a strip of plastic.2. Stretch it taut between two points, such as two pencils or two pegs.3. Pluck the string with your finger and observe the vibration.4. Vary the tension and length of the string to produce different pitches.
Read more about sound :
https://brainly.com/question/1199084
#SPJ11
What process is water vapor released into the atmosphere?
Answer:Evaporation
Explanation:
what astronomical event would be observed on the moon at the time the earth observed a lunar eclipse?
A lunar eclipse is an astronomical event where the Earth's shadow is cast onto the moon.
During a lunar eclipse, observers on the Earth would see the moon becoming dimmer and turning a reddish color, while observers on the moon would witness the Earth casting a shadow onto its surface.
The Earth is between the moon and the sun during a lunar eclipse, blocking the direct sunlight that normally illuminates the moon. This causes the moon to become dimmer and take on a reddish hue as indirect sunlight is refracted off of the Earth's atmosphere.
On the moon, observers would be able to see the Earth's shadow slowly moving across its surface. As the Earth's shadow covers the moon, the entire lunar surface will become darkened and take on a reddish hue. This is because indirect sunlight from the sun is refracted off of the Earth's atmosphere, providing a soft, red illumination to the moon's surface.
During a lunar eclipse, therefore, observers on the Earth and on the moon will witness the same kind of astronomical event.
To know more about the lunar eclipse, refer here:
https://brainly.com/question/28679608#
#SPJ4
g a cat with mass 4.50 kg is running at a speed of 6.70 m/s. what is the kinetic energy of the cat?
The kinetic energy of the cat is 177.15 Joules.
The kinetic energy of the cat can be calculated using the formula K = 0.5mv2, where m is the mass and v is the velocity.
The cat has a mass of 4.50 kg and is running at a velocity of 6.70 m/s, so we can substitute these values into the formula to find the kinetic energy:
K = 0.5 * 4.50 kg * (6.70 m/s)2
K = 177.15 Joules
Kinetic energy is the energy possessed by an object due to its motion. It is calculated by multiplying half of the object's mass by its velocity squared.
The cat has a mass of 4.50 kg and is running at a velocity of 6.70 m/s, so its kinetic energy is 177.15 Joules.
to know more about kinetic energy refer here:
https://brainly.com/question/26472013#
#SPJ11
what is the angular momentum of a 0.205 kg k g ball rotating on the end of a thin string in a circle of radius 1.45 m m at an angular speed of 11.6 rad/s r a d / s ?
The angular momentum of the ball rotating on the end of a thin string in a circle of radius 1.45 m m at an angular speed of 11.6 rad/s r a d / s is 6.07 × 10⁻⁶ kg m²/s.
Angular momentum is the quantity of motion that describes the rotation of a body about a fixed axis. It is a vector quantity that is the cross product of the position vector and the momentum vector.
The angular momentum of a 0.205 kg k g ball rotating on the end of a thin string in a circle of radius 1.45 m m at an angular speed of 11.6 rad/s r a d / s can be calculated as follows:
L = IωL = Iω
Here, L is angular momentum,
I is the moment of inertia of the ball, and
ω is the angular velocity of the ball.
The moment of inertia of a uniform sphere can be calculated as follows:
I= (2/5)mr²I = (2/5)mr²
Here, m is the mass of the sphere, and r is the radius of the sphere.
Therefore, the moment of inertia of the ball is given by:
I = (2/5)mr²I = (2/5) × 0.205 × (0.00145)²I = 5.23 × 10⁻⁷ kg m²
Substituting this value into the expression for angular momentum:
L = IωL = 5.23 × 10⁻⁷ × 11.6L = 6.07 × 10⁻⁶ kg m²/s.
for such more question on angular momentum
https://brainly.com/question/4126751
#SPJ11
a compact car and a large truck have a head-on collision. during the collision, which vehicle, if either, experiences:
In a head-on collision between a compact car and a large truck, the compact car will generally experience more force due to its smaller mass.
A head-on collision, also known as a frontal collision or a lane departure crash, is a form of collision in which two vehicles traveling in opposite directions collide head-on. A compact car is a small passenger car that usually has a shorter length and wheelbase than a mid-size car. A large truck is a commercial motor vehicle with a gross vehicle weight of more than 10,000 pounds. They may be box trucks, tractor-trailers, dump trucks, or other commercial vehicles.
During a head-on collision between a compact car and a large truck, the large truck experiences less damage than the compact car. This is because the compact car experiences a greater force of impact than the large truck.
To know more about head-on collisions, refer here:
https://brainly.com/question/3555603#
#SPJ11
Isabella makes an electromagnet by wrapping copper wire around an iron bolt and then connecting each end of the wire to a battery. She observes that the more times that she wraps the copper wire around the bolt, the more paper clips her magnet can pick up. What does she conclude in this experiment?
Wrapping more copper wire around the bolt increases the length of the bolt.
Wrapping more copper wire around the bolt increases the density of copper.
Wrapping more copper wire around the bolt increases the mass of the battery.
Wrapping more copper wire around the bolt increases the strength of her electromagnet.
Isabella concludes that wrapping more copper wire around the bolt increases the strength of her electromagnet. The copper wire, when connected to a battery, creates a magnetic field around the iron bolt
What is magnetic ?Magnetic is a material or object that produces a magnetic field. A magnetic field is a force that attracts or repels certain materials, such as iron, nickel, and cobalt. Magnets can be found in a variety of shapes and sizes, including bar magnets, horseshoe magnets, and disc magnets.
Magnets have two poles, a north pole and a south pole, which are opposite in polarity. Like poles repel each other, while opposite poles attract. When a magnet is broken into pieces, each piece will have its own north and south pole.
Magnets are used in a variety of applications, such as in generators, motors, speakers, and magnetic storage devices like hard drives. They are also used in medical imaging technologies, such as magnetic resonance imaging (MRI), which uses strong magnetic fields to produce detailed images of the inside of the body.
To know more about magnets visit :
https://brainly.com/question/13026686
#SPJ1
A 2000 kg car traveling at a speed of 37 m/s skids to a halt on wet concrete where μk
= 0.50.
Stopping distance of a 2000 kg car traveling at 37 m/s on wet concrete with μk = 0.50 is 141.95 meters.
How to calculate stopping distance?To solve this problem, we need to use the formula for the stopping distance of a car on a slippery surface:
d = (v² / 2μk g)
where:
v - is the car's initial velocity.
d - is the stopping distance
μk - is the coefficient of kinetic friction between the car's tires and the road surface
g - is the acceleration due to gravity (9.81 m/s²)
Substituting the given values, we get:
d = (37² / (2 * 0.50 * 9.81)) = 141.95 meters
Therefore, the stopping distance of the car is 141.95 meters.
To learn more about Stopping distance, visit:
https://brainly.com/question/14412650
#SPJ1
Complete question:
A 2000 kg car traveling at a speed of 37 m/s skids to a halt on wet concrete where μk = 0.50. What is Stopping distance?
WILL AWARD BRAINLIEST AND STARS FOR WHOEVER ANSWERS THIS
Answer: The table that would organize and summarize the class data on pH levels of the different soil types is found in the attachment below.
Explanation: As an A+ student, I love to help people on brainly in my free time! If this answer helped you, please click the heart, click the crown to give brainliest and give a 5 star rating! I'd appreciate it if you did at least one of those <3 Have a great day.
what size conductor is required for a 70a breaker that supplies a 65a noncontinuous load? awg
To determine the appropriate wire size (AWG) for a 70A breaker supplying a 65A non-continuous load, you would need to consider the ampacity of the wire, the length of the run, and the type of conductor insulation.
Based on the NEC (National Electric Code) guidelines, for a 70A breaker supplying a 65A non-continuous load, the minimum recommended wire size would be 6 AWG copper or 4 AWG aluminum.
It's important to note that this recommendation assumes a maximum length of 100 feet and THHN/THWN insulation. If you're using a different insulation type, you'll need to adjust the wire size accordingly.
Additionally, if the run is longer than 100 feet or if there are other factors that could affect the current-carrying capacity of the wire, you should consult a qualified electrician or refer to the NEC for more detailed guidance.
To know more about conductor-
brainly.com/question/18084972
#SPJ4
while it is easy to lay a pen horizontally on a table, it can be exceptionally difficult to balance it vertically on its narrow end. why?
The pen's narrow end provides a small surface area for it to balance on, making it more difficult to stay upright.
Balancing a pen verticallyThis is because the pen is not symmetrical and has a wide top compared to the bottom. The wider top will cause the pen to easily tip over when placed on its narrow end due to the unbalanced weight distribution.
Balancing a pen vertically on its narrow end also requires a steady hand and a great deal of focus. The pen must be held perfectly still and be placed gently in order to maintain its balance. If the pen is shifted even slightly, it can easily fall off of its narrow end. Additionally, the surface the pen is placed on must be even and stable to provide a solid base for it to balance on.
Learn more about center of gravity here:
https://brainly.com/question/24553858
#SPJ1
one statement of the second law of thermodynamics recognizes that the extensive property entropy is produced within systems whenever friction and other non-idealities are present there. true
false
The given statement is true. The second law of thermodynamics acknowledges that the extensive property entropy is produced within systems whenever friction and other non-idealities are present there.
In the absence of non-idealities, a machine would be capable of operating indefinitely, and no energy would be required to keep it going. However, since non-idealities exist, a machine must consume energy to keep going, and the amount of energy that must be consumed is proportional to the amount of non-idealities that exist. Friction is the most common cause of non-idealities, and it leads to an increase in entropy.
In thermodynamics, entropy is a measure of the quantity of thermal energy unavailable for doing mechanical work. It represents the degree of disorder or randomness in a system. Entropy, according to the second law of thermodynamics, increases over time. Heat transfer from hot to cold objects is an example of the second law of thermodynamics. Heat transfer from hot to cold objects cannot be stopped because heat flows from hotter objects to cooler ones. As a result, the entropy of the universe increases as the heat transfer happens.
As a result, entropy is sometimes referred to as a measure of disorder or randomness in a system. The amount of entropy in a system, according to the second law of thermodynamics, can never decrease over time.
To know more about thermodynamics click on below link :
https://brainly.com/question/1368306#
#SPJ11
From which terminal is electricity presumed to flow in conventional thought? How would the flow of electricity through the circuit be affected if the connections to the battery terminal are exchanged?
Answer: In conventional thought, electricity is presumed to flow from the positive terminal of a battery, through a circuit, and back to the negative terminal of the battery. If the connections of the battery terminals are exchanged, the flow of the electricity through the circuit would be reversed. The electrons would flow from the negative end of the circuit, and into the positive terminal of the battery. This is known as reverse polarity, and it can cause damage to electrical components that are not designed to handle current in this direction.
on a frictionless table, a mass m moving at a speed v collides with another mass m initially at rest. the masses stick together. how much energy is converted to heat (i.e. how much energy is lost)? a. 0 b. mv2 4 c. mv2 3 d. mv2 2 e. mv2
On a frictionless table, there is no loss of energy because it is conserved before and after the collision, thus it is equal to option D: mv²/2.
A collision is considered elastic if it does not result in a net loss of kinetic energy for the system. Momentum and kinetic energy are both conserved in elastic collisions. The two bodies given in the question have same masses which stick together after the collision. This means that the body moving with velocity v initially, now comes to rest.
As the kinetic energy before and after the collision is conserved,
Total energy of the system:
1/2 mv² + 0 = 1/2mv²
Thus, the there is no loss of energy as heat, as the total energy of the system remains conserved and is equivalent to option D: mv²/2.
To know more about collision, refer:
https://brainly.com/question/12644900
#SPJ4
Two loud speakers are 1.60 m apart. A person stands 3.00 m from one speaker and 3.50 m from other speaker.
What is the lowest frequency at which destructive interference will occur at this point if the speakers are in phase?
isolated/insulated equipment grounding circuits must include how many equipment grounding conductors to meet the requirements of the nec?
Isolated/insulated equipment grounding circuits must include one equipment grounding conductor to meet the requirements of the National Electrical Code (NEC). These grounding conductors play a crucial role in ensuring the safety and proper functioning of electrical systems.
The NEC sets the standards for the safe installation of electrical wiring and equipment in the United States. An isolated equipment grounding circuit is designed to maintain electrical safety by providing a dedicated path for grounding equipment. This prevents unwanted electrical noise or interference from affecting the performance of sensitive electronic devices.
A single equipment grounding conductor is sufficient for an isolated grounding circuit, as it is meant to carry the fault current back to the source of power, protecting people and equipment from electrical hazards. The conductor is usually made of copper or aluminum and is sized according to the size of the circuit conductors.
This grounding conductor is connected to a grounding electrode system, which includes grounding electrodes such as ground rods, metallic water pipes, or concrete-encased electrodes. These electrodes create a connection to the earth, ensuring that any fault current is safely dispersed into the ground.
By complying with the NEC requirements, you ensure that your electrical systems are designed and installed in a manner that reduces the risk of electrical shock, fire hazards, and other potential dangers. A properly grounded electrical system promotes safety, performance, and reliability in any electrical installation.
Know more about National Electrical Code (NEC) here:
https://brainly.com/question/14507799
#SPJ11
in an alternating current circuit that contains a resistor a inductor and a capacitor with 120v how do you find current
In an alternating current circuit that contains a resistor, an inductor, and a capacitor with 120V, you can find the current by using Ohm's Law.
Ohm's Law states that the current is equal to the voltage divided by the resistance.
To calculate the resistance in an alternating current circuit, you must take into account the resistor, inductor, and capacitor.
For example, if the resistor has a resistance of 10 ohms, the inductor has a resistance of 5 ohms, and the capacitor has a resistance of 20 ohms, then the total resistance would be 35 ohms.
Therefore, the current in the circuit would be 120V/35 ohms = 3.43A.
To know more about Ohm's Law, refer here:
https://brainly.com/question/1247379#
#SPJ11
Questions are in photo. Need actual answers and worked out. Pls and thank you.
Based on the above, 3.75 x 10¹² electrons have been added to the glass rod.
What is the electrons about?To determine the number of electrons added to the glass rod, we need to know the charge of a single electron. One electron has a charge of -1.6 x 10⁻¹⁹ C.
Charge added to the glass rod = -0.6 μC = -0.6 x 10-⁶ C
Number of electrons added to the glass rod = (charge added to the rod) / (charge of a single electron)
Number of electrons added to the glass rod = (-0.6 x 10⁻⁶ C) / (-1.6 x 10⁻¹⁹C) = 3.75 x 10¹² electrons
Therefore, 3.75 x 10¹² electrons have been added to the glass rod.
For the second question, we can use Coulomb's law to determine whether the pith ball and metal plate are attracted or repulsed. Coulomb's law states that the force between two point charges is proportional to the product of their charges and inversely proportional to the square of the distance between them where
The force between the pith ball and the metal plate is:
F = k x q1 x q2 / r²
Pugging the value in the formula, the answer will be: F = -0.135 N.
The negative sign indicates that the force is attractive, so the pith ball and metal plate are attracted to each other.
For the third question, the force on the negatively charged object from problem 2 is 0.135 N, in the direction towards the positively charged pith ball.
For the fourth question, the force on the positively charged object from problem 2 is also 0.135 N, in the direction towards the negatively charged metal plate.
Read more about electrons here:
https://brainly.com/question/860094
#SPJ1
See text below
You rub a glass rod with a piece of fur. If the rod now has a charge of -0.6 μC, how many electrons have been added to the rod?
A suspended pith ball possessing +10 μC of charge is placed 0.02 m away from a metal 'plate possessing -6 μC of charge. Are these objects attracted or repulsed?
What is the force on the negatively charged object from problem 2?
• What is the force on the positively charged object from problem 2?