The greatest common divisor of n and n + 1 where n is any positive integer is always 1. If a and b are positive integers such that [a, b] = (a, b), then a = b.
Prime decomposition of [tex]$2^1-1=1$[/tex] is 1.
gcd(n,n+1)
The greatest common divisor of n and n + 1 where n is any positive integer is always 1.
This is because for any two consecutive integers, the only integer that divides both of them is 1.
lcm[n,n+1]
The least common multiple of n and n + 1 where n is any positive integer is n(n + 1).
This is because for any two consecutive integers, the smallest integer that they both divide is their product
PROOF: If a and b are positive integers such that [a, b] = (a, b), then a = b.
Let us assume that a>b.
Then (a, b) = b.
Hence [tex]$[a, b] = ab$[/tex].
Thus [tex]$a b = [a, b] = (a, b) = b$[/tex].
Thus [tex]$a = 1$[/tex], which contradicts our assumption that [tex]$a>b$[/tex].
Hence it follows that [tex]$a\leq b$[/tex].
Similarly, it follows that [tex]$b\leq a$[/tex].
Therefore, we conclude that [tex]$a=b$[/tex].
Therefore, If a and b are positive integers such that [a, b] = (a, b), then a = b.
To know more about greatest common divisor, visit:
https://brainly.com/question/13257989
#SPJ11
King Arthur found it difficult to hold conversation with his 12 most trusted knights at the round table. So instead, he devises a plan to sit with just three of his knights at a time. If King Arthur proceeds with this plan three times a day, how many days will it take him to exhaust all possible ways of sitting with his knights? [Note: two arrangements are considered the same when a person has the same immediate left and right neighbors]
The number of days it will take King Arthur to exhaust all possible ways of sitting with his knights, three at a time, is 66, representing the number of unique arrangements.
In order to calculate the number of unique arrangements, we can consider the problem as arranging 3 knights around a circular table. The first knight can be chosen in 12 ways. After the first knight is seated, there are 11 remaining knights to choose from for the second seat. Finally, for the third seat, there are 10 remaining knights available. However, since the arrangement is circular, the order of the knights doesn't matter. This means that for each arrangement, we have counted each possibility three times (since there are three different starting points). Therefore, we divide the total number of arrangements by 3 to get the number of unique arrangements.
The formula for calculating the number of unique arrangements of seating 3 knights out of 12 can be expressed as:
[tex]\[\frac{{12 \times 11 \times 10}}{3} = 12 \times 11 \times 10 = 1,320\][/tex]
Since King Arthur proceeds with the plan three times a day, it will take him 66 days to exhaust all possible ways of sitting with his knights.
To learn more about arrangements refer:
https://brainly.com/question/1427391
#SPJ11
Can someone help please
Answer:
A. 3x³ - 24x
Step-by-step explanation:
-12 ÷ -4 = 3
x^4 ÷ x = x³
96 ÷ -4 = -24
x² ÷ x = x
(-12x^4 + 96x²) ÷ -4x = 3x³ - 24x
4 females? The probability of seiecting at least 4 females is (Type an integet or a simplified fraction.)
Therefore, the probability of selecting at least 4 females if there are 10 females in the sample is 0.0626 or 626/10,000. Answer: 626/10000.
The total number of females in the sample is not specified, which makes the question difficult to answer. As a result, I am assuming that there are 10 females in the sample. The formula for calculating the probability of choosing at least 4 females is P(X>=4).When X follows a binomial distribution, the formula for calculating P(X>=4) is as follows: P(X>=4) = P(X=4) + P(X=5) + P(X=6) + P(X=7) + P(X=8) + P(X=9) + P(X=10)
Let's find the probability of selecting at least 4 females if there are 10 females in the sample.
P(X=4) = (10 C 4)*(6 C 2)/ (16 C 6)
= 210*15/8008
= 0.0397P(X=5)
= (10 C 5)*(6 C 1)/ (16 C 6)
= 252*6/8008
= 0.0189P(X=6)
= (10 C 6)*(6 C 0)/ (16 C 6)
= 210*1/8008
= 0.0026P(X=7)
= (10 C 7)*(6 C 0)/ (16 C 6)
= 120*1/8008
= 0.0013P(X=8)
= (10 C 8)*(6 C 0)/ (16 C 6)
= 45*1/8008
= 0.0002P(X=9)
= (10 C 9)*(6 C 0)/ (16 C 6)
= 10*1/8008
= 0.000P(X=10)
= (10 C 10)*(6 C 0)/ (16 C 6)
= 1*1/8008
= 0P(X>=4)
= P(X=4) + P(X=5) + P(X=6) + P(X=7) + P(X=8) + P(X=9) + P(X=10)
= 0.0626
Therefore, the probability of selecting at least 4 females if there are 10 females in the sample is 0.0626 or 626/10,000. Answer: 626/10000.
To know more abou probability visit;
brainly.com/question/31828911
#SPJ11
A mass weighing 64 pounds is attached to a spring whose constant is 21 lb/ft. The medium offers a damping force equal 24 times the instantaneous velocity. The mass is initially released from the equilibrium position with a downward velocity of 9 ft/s. Determine the equation of motion. (Use g = 32 ft/s² for the acceleration due to gravity.)
The equation of motion for the given scenario is[tex]a = -0.375v - 32.66 ft/s^2[/tex]
To determine the equation of motion for the given scenario, we can start by applying Newton's second law of motion:
F = ma
Where F is the net force acting on the mass m is the mass & a is the acceleration.
In this case, the net force consists of three components: the force due to the spring, the force due to damping, and the force due to gravity.
Force due to the spring:
The force exerted by the spring is given by Hooke's Law:
Fs = -kx
Where Fs is the force exerted by the spring, k is the spring constant, and x is the displacement from the equilibrium position. The negative sign indicates that the force is in the opposite direction of the displacement.
In this case, the displacement x is given by:
[tex]x = 64 lb / (32 ft/s^2) = 2 ft[/tex]
So, the force due to the spring is:
Fs = -21 lb/ft * 2 ft = -42 lb
Force due to damping:
The force due to damping is given by:
Fd = -cv
where Fd is the force due to damping, c is the damping constant, and v is the velocity.
In this case, the damping force is 24 times the instantaneous velocity:
Fd = -24 * v
Force due to gravity:
The force due to gravity is simply the weight of the mass:
Fg = mg
where Fg is the force due to gravity, m is the mass, and g is the acceleration due to gravity.
In this case, the mass is 64 lb, so the force due to gravity is:
[tex]Fg = 64 lb * 32 ft/s^2 = 2048 lb-ft/s^2[/tex]
Now, we can write the equation of motion:
F = ma
Summing up the forces, we have:
Fs + Fd + Fg = ma
Substituting the expressions for each force:
[tex]-42 lb - 24v - 2048 lb·ft/s^2 = 64 lb * a[/tex]
Simplifying:
[tex]-24v - 2090 lb·ft/s^2 = 64 lb * a[/tex]
Dividing by 64 lb to express the acceleration in ft/s²:
[tex]-0.375v - 32.66 ft/s^2 = a[/tex]
Thus, the equation of motion for the given scenario is:
[tex]a = -0.375v - 32.66 ft/s^2[/tex]
Learn more about Newton's second law of motion:-
https://brainly.com/question/2009830
#SPJ4
what else would need to be congruent to show that ABC=CYZ by SAS
To show that two triangles ABC and CYZ are congruent using the Side-Angle-Side (SAS) criterion: Side AB congruent to side CY, Side BC congruent to side YZ and Angle B congruent to angle Y.
To show that two triangles ABC and CYZ are congruent using the Side-Angle-Side (SAS) criterion, we would need to establish the following congruences:
Side AB congruent to side CY: We need to show that the length of side AB is equal to the length of side CY.Side BC congruent to side YZ: We need to demonstrate that the length of side BC is equal to the length of side YZ.Angle B congruent to angle Y: We need to prove that angle B is equal to angle Y.These three congruences combined would satisfy the SAS criterion and establish the congruence between triangles ABC and CYZ.
By showing that the corresponding sides and angles of the two triangles are congruent, we can conclude that the triangles are identical in shape and size.
For such more question on congruent:
https://brainly.com/question/28262429
#SPJ8
Write in detailed the scope and limitation when calculating the friction loass from sudden expansion and contraction of cross section.
Friction loss due to sudden expansion and contraction of cross-section is calculated to determine the efficiency of piping systems.
When calculating the friction loss from sudden expansion and contraction of cross-section, it is important to consider the scope and limitations of the calculation process.
Scope: The scope of calculating the friction loss from sudden expansion and contraction of cross-section is to determine the amount of energy that is lost due to the change in cross-sectional area. This calculation is essential in determining the efficiency of piping systems and helps in identifying any potential problems that may arise due to the changes in cross-sectional area.
Limitations: There are certain limitations when calculating the friction loss from sudden expansion and contraction of cross-section. These include:1. Inaccuracies in Calculation: Calculating the friction loss from sudden expansion and contraction of cross-section requires a certain degree of accuracy. Any inaccuracy in the calculation process may lead to errors in the final results.2. Neglecting Other Factors: The calculation process only takes into account the frictional losses due to the change in cross-sectional area. Other factors that may contribute to the overall frictional losses, such as roughness of the piping material and fluid properties, are often neglected.
3. Limitations of the Equations: The equations used in calculating the friction loss from sudden expansion and contraction of cross-section have certain limitations. These equations are based on certain assumptions and may not be applicable in all situations.
In summary, the calculation of friction loss due to sudden expansion and contraction of cross-section is an important aspect of determining the efficiency of piping systems.
To know more about friction loss, click here
https://brainly.com/question/28148490
#SPJ11
b) How many milliliters of C₂H₂ (g) can be collected over water at 27.0 degrees C and 700. mm Hg if 20.6 g of BaC₂ (s) and 10.- g of water react? Use the editor to format your answer
Question 1
The partial pressure of C₂H₂ is (700.0 - 26.7) = 673.3 mm Hg, at 27.0°C and the mole of C₂H₂ produced is 0.1388.
The balanced equation for the reaction between BaC₂ (s) and H₂O (l) to produce C₂H₂ (g) and Ba(OH)₂ (s) is given below: \[BaC_2 + 2H_2O \rightarrow C_2H_2 + Ba(OH)_2\]
The mole of BaC₂ (s) used in the reaction will be: \[n_{BaC_2} = \frac{20.6 g}{(2\times 208.23\;g/mol)} = 0.0496\;mol\]
The C₂H₂ produced.
\[\frac{n_{H_2O}}{2} = \frac{0.2777\;mol}{2} = 0.1388\;mol\]
The volume of C₂H₂ (g) produced at 700. mm Hg and 27.0 degrees C can be calculated using the ideal gas law equation: \[PV = nRT\] where P is pressure, V is volume, n is moles, R is the gas constant and T is temperature in Kelvin.
The density of water at 27.0 degrees C is 0.997 g/mL.
Therefore the vapor pressure of water at 27.0 degrees C is 26.7 mm Hg.
Therefore the partial pressure of C₂H₂ is (700.0 - 26.7) = 673.3 mm Hg.
The temperature of 27.0 degrees C is 300.15 K.
Substituting all these values into the equation and solving for V:
\[V_{C_2H_2} = \frac{n_{C_2H_2}RT}{P_{C_2H_2}} = \frac{(0.1388\;mol)(0.0821\;L \cdot atm/mol \cdot K)(300.15\;K)}{673.3\;mm Hg\times 1 atm/760.0\;mm Hg} = 1.60\;L\]
Finally, the volume of C₂H₂ produced is collected over water at 27.0 degrees C and hence the final volume of C₂H₂ (g) is: \[V_{C_2H_2}\;at\;27.0^\circ C = V_{C_2H_2}\;at\;700.0\;mm Hg = 1.60\;L\]
The final volume of C₂H₂ (g) collected over water at 27.0 degrees C is 1.60 L.
This volume is obtained when 20.6 g of BaC₂ and 10.0 g of water react to form C₂H₂ and Ba(OH)₂.
The volume of C₂H₂ (g) is calculated using the ideal gas law equation.
The partial pressure of C₂H₂ is (700.0 - 26.7) = 673.3 mm Hg, at 27.0°C and the mole of C₂H₂ produced is 0.1388.
To know more about partial pressure, visit:
brainly.com/question/16749630
#SPJ11
V = (moles of C₂H₂ × 0.0821 L·atm/(mol·K) × 300.15 K) / 0.9211 atm
Now, you can plug in the values and calculate the volume of C₂H₂ gas collected over water.
To determine the volume of C₂H₂ gas collected over water, we need to use the ideal gas law and account for the presence of water vapor. Here's how you can calculate it:
1. Determine the moles of BaC₂ (s):
Given mass of BaC₂ (s) = 20.6 g
Molar mass of BaC₂ = 208.23 g/mol
Moles of BaC₂ = mass / molar mass = 20.6 g / 208.23 g/mol
2. Determine the moles of H₂O (g):
Given mass of H₂O (g) = 10.0 g
Molar mass of H₂O = 18.015 g/mol
Moles of H₂O = mass / molar mass = 10.0 g / 18.015 g/mol
3. Determine the limiting reactant:
BaC₂ (s) + 2 H₂O (g) → 2 HC≡CH (g) + Ba(OH)₂ (aq)
The mole ratio between BaC₂ and H₂O is 1:2.
Compare the moles of BaC₂ and H₂O to find the limiting reactant.
The limiting reactant is the one with fewer moles.
4. Calculate the moles of C₂H₂ produced:
From the balanced equation, the mole ratio between BaC₂ and C₂H₂ is 1:2.
Moles of C₂H₂ = 2 × moles of limiting reactant
5. Apply the ideal gas law to find the volume of C₂H₂ gas:
Given:
Temperature (T) = 27.0°C = 27.0 + 273.15 = 300.15 K
Pressure (P) = 700 mm Hg
Convert pressure to atm:
700 mm Hg × (1 atm / 760 mm Hg) = 0.9211 atm
V = (nRT) / P
n = moles of C₂H₂
R = ideal gas constant = 0.0821 L·atm/(mol·K)
T = temperature in Kelvin
Calculate the volume:
V = (moles of C₂H₂ × 0.0821 L·atm/(mol·K) × 300.15 K) / 0.9211 atm
To know more about volume visit:
brainly.com/question/28058531
#SPJ11
What is the optimal solution for the following problem?
Maximize
P = 3x + 15y
subject to
2x + 6y ≤ 12
5x + 2y ≤ 10
and x = 0, y ≥ 0.
(x, y) = (2, 1)
(x, y) = (2, 0)
(x, y) = (1, 5)
(x, y) = (3,0)
(x, y) = (0,3)
Among the given feasible points, the optimal solution that maximizes the objective function P = 3x + 15y is (x, y) = (1, 5), which results in the maximum value of P = 78.
To find the optimal solution for the given problem, we need to maximize the objective function P = 3x + 15y subject to the given constraints.
The constraints are as follows:
2x + 6y ≤ 12
5x + 2y ≤ 10
x = 0 (non-negativity constraint for x)
y ≥ 0 (non-negativity constraint for y)
We can solve this problem using linear programming techniques. We will evaluate the objective function at each feasible point and find the point that maximizes the objective function.
Let's evaluate the objective function P = 3x + 15y at each feasible point:
(x, y) = (2, 1)
P = 3(2) + 15(1) = 6 + 15 = 21
(x, y) = (2, 0)
P = 3(2) + 15(0) = 6 + 0 = 6
(x, y) = (1, 5)
P = 3(1) + 15(5) = 3 + 75 = 78
(x, y) = (3, 0)
P = 3(3) + 15(0) = 9 + 0 = 9
(x, y) = (0, 3)
P = 3(0) + 15(3) = 0 + 45 = 45
From the above evaluations, we can see that the maximum value of P is 78, which occurs at (x, y) = (1, 5).
Therefore, the optimal solution for the given problem is (x, y) = (1, 5) with P = 78.
Learn more about optimal solution here:
https://brainly.com/question/14914110
#SPJ11
Calculate length of d
The value of the missing length d using law of sines is: 28.97 m
How use law of sines and cosines?If only one of these is missing, the law of cosines can be used.
3 sides and 1 angle. So if the known properties of a triangle are SSS (side-side-side) or SAS (side-angle-side), then this law applies.
If you want the ratio of the sine of an angle and its inverse to be equal, you can use the law of sine. This can be used if the triangle's known properties are ASA (angle-side-angle) or SAS.
Using law of sines, we ca find the missing length d as:
d/sin 43 = 38.5/sin 65
d = (38.5 * sin 43)/sin 65
d = 28.97 m
Read more about law of sines and cosines at: https://brainly.com/question/10254615
#SPJ1
If a1,a2,…..an is a complete set of residues modulo n and g.c.d. (a,n)=1, then show that aa1,aa2,…..aan is also a complete set of residues modulo n. 6. Solve the linear congruence 25x≡15(mod29).
The linear congruence 25x ≡ 15 (mod 29) is x ≡ 9 (mod 29).
Given that a₁, a₂, …, aₙ is a complete set of residues modulo n and g.c.d. (a, n) = 1
Suppose that, if possible, aaᵢ ≡ aaⱼ (mod n) for some i and j such that
1 ≤ i < j ≤ n⇒ a * aᵢ ≡ a * aⱼ (mod n)⇒ a * (aⱼ - aᵢ) ≡ 0 (mod n)
Since g.c.d. (a, n) = 1,
then g.c.d. (a * (aⱼ - aᵢ), n) = g.c.d. (aⱼ - aᵢ, n) = d(d|n)
Since aᵢ and aⱼ are distinct residues, so they are also co-prime with n.
Thus, their difference (aⱼ - aᵢ) is also co-prime with n.
So, d = 1 and aⱼ ≡ aᵢ (mod n), which is a contradiction.
Hence aa₁, aa₂, …, aa n must be a complete set of residues modulo n. Q:
Solve the linear congruence 25x ≡ 15 (mod 29)
Let us find the multiplicative inverse of 25 in mod 29 by Euclid's Algorithm.
29 = 25 * 1 + 429 = 4 * 7 + 125 = 5 * 4 + 525 = 1 * 5 + 0
Hence, the multiplicative inverse of 25 in mod 29 is 5.
Now, multiply both sides of the equation by the inverse of 25 (which is 5) to get,
5(25x) ≡ 5(15) (mod 29)⇒ 125x ≡ 75 (mod 29)⇒ 2x ≡ 17 (mod 29)
Now, the congruence 2x ≡ 17 (mod 29) isx ≡ 9 (mod 29)
Therefore, the linear congruence 25x ≡ 15 (mod 29) is x ≡ 9 (mod 29).
To know more about linear congruence visit:
https://brainly.com/question/32700407
#SPJ11
SETB: What is the minimum diameter in mm of a solid steel shaft that
will not twist through more than 3º in a 6-m length when subjected
to a torque of 12 kNm? What maximum shearing stress is develo
The minimum diameter of the solid steel shaft is approximately 42.9 mm.
the minimum diameter of a solid steel shaft can be determined by considering the torque applied and the desired maximum twist angle. To calculate the minimum diameter, we can use the formula:
[tex]τ = (T * L) / (π * d^4 / 32)[/tex]
where:
τ is the maximum shearing stress,
T is the torque (12 kNm),
L is the length of the shaft (6 m),
d is the diameter of the shaft.
We need to rearrange the formula to solve for d:
[tex]d^4 = (32 * T * L) / (π * τ)[/tex]
The shaft does not twist more than 3º, we can set the twist angle to radians:
[tex]θ = (π / 180) * 3[/tex]
Now we can calculate the maximum shearing stress using the formula:
[tex]τ = (T * L) / (π * d^4 / 32)[/tex]
Substituting the given values, we have:
[tex]τ = (12,000 Nm * 6 m) / (π * d^4 / 32)[/tex]
Let's assume the maximum shearing stress is 150 MPa (mega pascals). We can substitute this value into the equation:
[tex]150 MPa = (12,000 Nm * 6 m) / (π * d^4 / 32)[/tex]
Now we can solve for the minimum diameter, d:
[tex]d^4 = (32 * 12,000 Nm * 6 m) / (π * 150 MPa)\\d^4 = (76,800 Nm * m) / (3.1416 * 150 MPa)\\d^4 = 162.787 Nm * m / MPa[/tex]
Taking the fourth root of both sides:
[tex]d = (162.787 Nm * m / MPa)^(1/4)[/tex]
The minimum diameter of the solid steel shaft is approximately 42.9 mm.
Learn more about diameter with the given link,
https://brainly.com/question/28162977
#SPJ11
Numer 72
69, 70, 71, and 72 Find the volume obtained by rotating the region bounded by the curves about the given axis. 69. Y sin r, y=0, x/2
To find the volume obtained by rotating the region bounded by the curves about the given axis, we need to determine the integration limits and set up an integral.
The region is bounded by the curves y = sin(x), y = 0, and x/2.
To find the limits of integration, we need to determine the x-values where the curves intersect. The curve y = sin(x) intersects the x-axis at x = 0, π, 2π, and so on. Since we are considering the interval from 0 to x/2, our limits of integration will be from 0 to π. The radius of rotation is given by r = y. In this case, r = sin(x). The volume V obtained by rotating the region can be calculated using the formula: V = π ∫[a, b] r^2 dx
Substituting the values, the integral becomes: V = π ∫[0, π] (sin(x))^2 dx
Simplifying further: V = π ∫[0, π] sin^2(x) dx
This integral can be evaluated to obtain the volume V. After integrating, the volume obtained by rotating the region bounded by the curves about the given axis will be determined.
Learn more about integral here
https://brainly.com/question/30094386
#SPJ11
Please help <3 The grade distribution of the many
students in a geometry class is as follows.
Grade
A B
C D F
Frequency 28 35 56 14 7
Find the probability that a student earns a
grade of A.
P(A) = [?]
Probability
Enter
Answer:
0.2 or 20%
Step-by-step explanation:
The definition of probability is "the number of favorable outcomes over the total number of outcomes". So, to find the probability of someone getting an A, we must:
- Find the Frequency of Someone Getting an A
- Find the Total Frequency of the Distribution
- Divide the Two
As we can see in the table, if we add the Frequencies:
28 + 35 + 56 + 14 + 7 = ?
We get a total of:
140
Looking at the table once more, if we look at the frequency of someone getting an A, we can see that it is:
28
So, if we find the ratio of both values, like so down below:
28 : 140
And simplify it:
28 : 140 = 1 : 5
We can see that the ratio is simplified to 1 : 5, or in decimal and percentage terms, 0.2 and 20%.
La función f(x) = 68(1.3) * representa la posible población de ardillas en un parque dentro de x años. Cada año , la cantidad de ardillas esperada de ardillas es cuantas veces mas que el año anterior?
The expected number of squirrels in the park increases by a factor of 1.3 each year.
The given function, f(x) = 68(1.3)^x, represents the possible population of squirrels in a park after x years. To determine how many times the expected number of squirrels increases each year, we can compare the population at consecutive years.
Let's consider two consecutive years, x and x+1. The population at year x is given by f(x) = 68(1.3)^x, and the population at year x+1 is given by f(x+1) = 68(1.3)^(x+1).
To find how many times the population increases, we can divide f(x+1) by f(x):
f(x+1)/f(x) = [68(1.3)^(x+1)] / [68(1.3)^x]
= (1.3)^(x+1 - x)
= 1.3
Therefore, the expected number of squirrels in the park increases by a factor of 1.3 each year. In other words, the population of squirrels is expected to grow by 1.3 times every year.
For more questions on factor, click on:
https://brainly.com/question/24351176
#SPJ8
The temperature is below 2 degrees Fahrenheit.
t < 2
Can someone who took the test answer pls?
In the context of inequalities and number lines, let's analyze each statement: 1. "A number line going from 0 to 3. A closed circle is at 2. Everything to the left of the circle is shaded."
This represents the inequality t ≤ 2, where t represents a value on the number line. The closed circle at 2 indicates that 2 is included as a valid solution to the inequality.
The shading to the left of the circle represents all values less than or equal to 2, including 2 itself.
2. "A number line going from 0 to 3. An open circle is at 2. Everything to the left of the circle is shaded."
This represents the inequality t < 2, where t represents a value on the number line. The open circle at 2 indicates that 2 is not included as a valid solution to the inequality.
The shading to the left of the circle represents all values strictly less than 2.
3. "A number line going from 0 to 3. An open circle is at 2. Everything to the right of the circle is shaded."
This represents the inequality t > 2, where t represents a value on the number line. The open circle at 2 indicates that 2 is not included as a valid solution to the inequality.
The shading to the right of the circle represents all values greater than 2.
- A closed circle (filled-in circle) represents inclusion.
- An open circle represents exclusion.
- Shading to the left of the circle indicates values less than the given number.
- Shading to the right of the circle indicates values greater than the given number.
For more such questions on inequalities,click on
https://brainly.com/question/25275758
#SPJ8
Mr. Ganzon has a newly constructed 4 story Commercial Building located at Isabela City, Basilan. The building has a total fixture consist of the following; water closet (WC)=130, Urinal (UR)= 30, Shower head (SHO)= 12, Lavatories (LAV)= 100, and service sinks (SS)= 27. Given the following fixture demand (WC=8.0, UR= 4.0, SHO=2.0, LAV=1.0, SS=3.0)
a. Using UPC, determine the total water supply fixture units (WSFU) for the water closet
b. Using UPC, determine the total water supply fixture units (WSFU) for the urinal
c. Using UPC, determine the total water supply fixture units (WSFU) for shower head
d. Using UPC, determine the total water supply fixture units (WSFU) for the lavatories
e. Using UPC, determine the total water supply fixture units (WSFU) for the service sink
f. Calculate the total fixture units of the building demand
a. The first step is to determine the Water Supply Fixture Unit (WSFU) for the water closet (WC) using the Uniform Plumbing Code (UPC). The UPC provides a standard value for each type of fixture based on its water demand. For a water closet, the UPC assigns a value of 8.0 WSFU.
b. Next, we can determine the WSFU for the urinal (UR). According to the UPC, a urinal has a value of 4.0 WSFU.
c. Moving on to the shower head (SHO), the UPC assigns a value of 2.0 WSFU for each shower head.
d. For lavatories (LAV), the UPC assigns a value of 1.0 WSFU per lavatory.
e. Lastly, for service sinks (SS), the UPC assigns a value of 3.0 WSFU per service sink.
f. To calculate the total fixture units of the building demand, we need to multiply the quantity of each fixture type by its corresponding WSFU value, and then sum up the results.
Here are the calculations:
WC: 130 fixtures x 8.0 WSFU = 1040.0 WSFU
UR: 30 fixtures x 4.0 WSFU = 120.0 WSFU
SHO: 12 fixtures x 2.0 WSFU = 24.0 WSFU
LAV: 100 fixtures x 1.0 WSFU = 100.0 WSFU
SS: 27 fixtures x 3.0 WSFU = 81.0 WSFU
Adding up these results, we have a total of 1365.0 WSFU for the building demand.
Therefore, the total fixture units of the building demand is 1365.0 WSFU.
To learn more about lavatory
https://brainly.com/question/14336634
#SPJ11
Determine the amount concentration, in mol/L, of 0.533 moles of sulfuric acid dissolved in a 123 mL solution.
The amount concentration of 0.533 moles of sulfuric acid dissolved in a 123 mL solution is approximately 4.34 mol/L.
To determine the amount concentration (also known as molarity), we need to calculate the number of moles of sulfuric acid per liter of solution.
Amount of sulfuric acid = 0.533 moles
Volume of solution = 123 mL = 0.123 L
To calculate the amount concentration (molarity), we use the formula:
Molarity (M) = Amount of solute (in moles) / Volume of solution (in liters)
Molarity = 0.533 moles / 0.123 L
Molarity = 4.34 mol/L
Therefore, the amount concentration of 0.533 moles of sulfuric acid dissolved in a 123 mL solution is approximately 4.34 mol/L.
Learn more about concentration at https://brainly.com/question/15583382
#SPJ11
Indicate whether energy is emitted or absorbed when the following electronic transitions occur in hydrogen: (a) from n=2 to n=6,
(b) from an orbit of radius 4.76 A˚ to one of radius 0.529 A˚
(c) from the n=6 to the n=9 state.
(a) Transition from n=2 to n=6: Energy is absorbed.
(b) Transition from radius 4.76 Å to radius 0.529 Å: Energy is emitted.
(c) Transition from n=6 to n=9: Energy is emitted.
(a) When an electron transitions from n=2 to n=6 in hydrogen, energy is absorbed. This is because electrons in higher energy levels have greater energy, and when they move to a higher level, they need to absorb energy.
(b) When an electron transitions from an orbit of radius 4.76 Å to one of radius 0.529 Å, energy is emitted. This is because electrons in smaller orbits have lower energy, and when they move to a lower energy level, they release excess energy in the form of electromagnetic radiation.
(c) When an electron transitions from the n=6 to the n=9 state in hydrogen, energy is emitted. Similar to the previous case, electrons moving to lower energy levels release excess energy, resulting in the emission of energy.
In summary:
(a) Energy is absorbed.
(b) Energy is emitted.
(c) Energy is emitted.
To learn more about energy visit : https://brainly.com/question/2003548
#SPJ11
Explain why the frame analysis requires us to disassemble the
members? Why didn't we have to disassemble members when using the
method of joints for truss analysis
Frame analysis is a technique used to calculate the internal forces or stresses of each member of a structural framework that is subject to external forces. It requires us to disassemble members so that the structural framework can be evaluated in its smaller components or individual parts.
The primary objective of frame analysis is to determine the loads acting on each member. To do so, we must know the precise load distribution along each member, which can only be achieved by breaking the structural framework down into smaller components or individual parts. In the end, it aids us in determining the design's structural integrity, enabling us to avoid potential catastrophes. Frame analysis is especially useful for structures such as buildings, bridges, and other structures that are subjected to numerous and varied loads.While Method of Joints is a technique used to calculate the internal forces or stresses of each member in a truss that is subject to external forces. In this method, each joint is evaluated individually. This method entails cutting each joint in a truss structure and analyzing the forces at the joints. The calculation of the member forces or stresses is then performed in this way. Since the members in a truss are not usually subjected to bending, we may analyze them using the Method of Joints rather than Frame analysis, which is a more complicated and time-consuming method. Consequently, it is not necessary to disassemble members when using the Method of Joints for truss analysis.
To know more about Frame analysis visit:
https://brainly.com/question/7345111
#SPJ11
Solve the following and prvide step by step explanations PLEASE PLEASE I'VE GOT LITLE TIME LEFT PLEASE
a. The equivalent angle within the given range is θ = 445°.
b. The value of cot θ is √5/2.
c. The value of θ is approximately 143.13°.
a. To find θ where tan θ = tan 265° and θ ≠ 265°, we can use the periodicity of the tangent function, which repeats every 180°. Since tan θ = tan (θ + 180°), we can find the equivalent angle within the range of 0° to 360°.
First, let's add 180° to 265°:
θ = 265° + 180°
θ = 445°
So, the equivalent angle within the given range is θ = 445°.
b. Given sin θ = 2/3 and cos θ > 0, we can use the Pythagorean identity sin²θ + cos²θ = 1 to find the value of cos θ. Since sin θ = 2/3, we have:
(2/3)² + cos²θ = 1
4/9 + cos²θ = 1
cos²θ = 1 - 4/9
cos²θ = 5/9
Since cos θ > 0, we take the positive square root:
cos θ = √(5/9)
cos θ = √5/3
To find cot θ, we can use the reciprocal identity cot θ = 1/tan θ. Since tan θ = sin θ / cos θ, we have:
cot θ = 1 / (sin θ / cos θ)
cot θ = cos θ / sin θ
Substituting the values of sin θ and cos θ:
cot θ = (√5/3) / (2/3)
cot θ = √5 / 2
Therefore, the value of cot θ is √5/2.
c. Given the equation 5/2 cos θ + 4 = 2, we can solve for θ:
5/2 cos θ + 4 = 2
5/2 cos θ = 2 - 4
5/2 cos θ = -2
cos θ = -2 * 2/5
cos θ = -4/5
To find θ, we can use the inverse cosine function (cos⁻¹):
θ = cos⁻¹(-4/5)
Using a calculator, we find that θ ≈ 143.13°.
Therefore, the value of θ is approximately 143.13°.
for such more question on equivalent angle
https://brainly.com/question/2972832
#SPJ8
Giving 50 points to whoever gets it right
Answer: 10 sq in
Step-by-step explanation:
Area = base x height
= 5 in x 2 in
= 10 sq in
Jane is on the south bank of a river and spots her lost dog upstream on the north bank of the river. The river is 15 meters wide, completely still, and runs perfectly straight, east/west. If she swims straight north across the river and stops immediately on shore, her dog will then be 100 meters due east of her. However, she wants to reach the dog as fast as possible and considers taking a diagonal route across the river instead. She can move on land at 5 meters per second and move through water at 4 meters per second. If Jane enters the water immediately and follows the fastest possible route, how many seconds will it take her to reach her dog? Express your answer as an exact decimal. Jane is on the south bank of a river and spots her lost dog upstream on the north bank of the river. The river is 15 meters wide, completely still, and runs perfectly straight, east/west. If she swims straight north across the river and stops immediately on shore, her dog will then be 100 meters due east of her. However, she wants to reach the dog as fast as possible and considers taking a diagonal route across the river instead. She can move on land at 5 meters per second and move through water at 4 meters per second. If Jane enters the water immediately and follows the fastest possible route, how many seconds will it take her to reach her dog? Express your answer as an exact decimal and submit at link in bio.
Jane should take a diagonal route across the river to reach her dog as fast as possible. To find the fastest possible time, we can apply the law of cosines to calculate the diagonal distance across the river, then use this distance along with the land speed and water speed to determine the total time it takes Jane to reach her dog.
Let the point where Jane starts swimming be A and the point where she stops on the north bank be B. Let C be the point directly across the river from A and D be the point directly across from B. Then ABCD forms a rectangle, and we are given AB = 100 meters, BC = CD = 15 meters, and AD = ? meters, which we need to calculate. Applying the Pythagorean Theorem to triangle ABC gives:
AC² + BC² = AB²,
so
AC² = AB² - BC² = 100² - 15² = 9,925
and
AC ≈ 99.624 meters,
which is the length of the diagonal across the river. We can now use the law of cosines to find AD:
cos(90°) = (AD² + BC² - AC²) / (2 × AD × BC)0 = (AD² + 15² - 9,925) / (2 × AD × 15)
Simplifying and solving for AD gives: AD ≈ 58.073 meters This is the distance Jane must travel to reach her dog if she takes a diagonal route. The time it takes her to do this is: time = (distance across water) / (speed in water) + (distance on land) / (speed on land)time = 99.624 / 4 + 58.073 / 5time ≈ 25.197 seconds
The fastest possible time for Jane to reach her dog is approximately 25.197 seconds.
To learn more about law of cosines visit:
brainly.com/question/30766161
#SPJ11
A 350 mm x 700 mm concrete beam has a simple span of 10 m and prestressed with a parabolic-curved tendon with a maximum sag of 200 mm at midspan. The beam is to carry a total uniform load of 20 kN/m including its own weight. Assume tension stresses as positive and compressive as negative. Determine the following: 1. The effective prestress required for the beam to have no deflection on the given load. 2. The stress in the bottom fiber of the section at midspan for the above condition. 3. The value of the concentrated load to be added at midspan in order that no tension will occur in the section.
The stress in the bottom fiber of the section at midspan under the given condition is approximately -2.08 MPa.
To determine the required values for the prestressed concrete beam, we can follow the following steps:
Effective Prestress for No Deflection:
The effective prestress required can be calculated using the following equation:
Pe = (5 * w * L^4) / (384 * E * I)
Where:
Pe = Effective prestress
w = Total uniform load including its own weight (20 kN/m)
L = Span length (10 m)
E = Modulus of elasticity of concrete
I = Moment of inertia of the beam's cross-section
Assuming a rectangular cross-section for the beam (350 mm x 700 mm) and using the formula for the moment of inertia of a rectangle:
I = (b * h^3) / 12
Substituting the values:
I = (350 mm * (700 mm)^3) / 12
I = 171,500,000 mm^4
Assuming a modulus of elasticity of concrete (E) as 28,000 MPa (28 GPa), we can calculate the effective prestress:
Pe = (5 * 20 kN/m * (10 m)^4) / (384 * 28,000 MPa * 171,500,000 mm^4)
Pe ≈ 0.305 MPa
Therefore, the effective prestress required for the beam to have no deflection under the given load is approximately 0.305 MPa.
Stress in Bottom Fiber at Midspan:
To find the stress in the bottom fiber of the section at midspan, we can use the following equation for a prestressed beam:
σ = Pe / A - M / Z
Where:
σ = Stress in the bottom fiber at midspan
Pe = Effective prestress (0.305 MPa, as calculated in step 1)
A = Area of the beam's cross-section (350 mm * 700 mm)
M = Bending moment at midspan
Z = Section modulus of the beam's cross-section
Assuming the beam is symmetrically loaded, the bending moment at midspan can be calculated as:
M = (w * L^2) / 8
Substituting the values:
M = (20 kN/m * (10 m)^2) / 8
M = 312.5 kNm
Assuming a rectangular cross-section, the section modulus (Z) can be calculated as:
Z = (b * h^2) / 6
Substituting the values:
Z = (350 mm * (700 mm)^2) / 6
Z = 85,583,333.33 mm^3
Now we can calculate the stress in the bottom fiber at midspan:
σ = (0.305 MPa) / (350 mm * 700 mm) - (312.5 kNm) / (85,583,333.33 mm^3)
σ ≈ -2.08 MPa
Therefore, the stress in the bottom fiber of the section at midspan under the given condition is approximately -2.08 MPa (compressive stress). So, eliminate tension in the section, we need to add a concentrated load at midspan that counteracts the tensile forces.
To more about stress, visit:
https://brainly.com/question/26108464
#SPJ11
A UAP (unidentified aerial phenomena) was spotted with an acceleration vector of a = 20i +30j - 60k in m/8^2. It's estimated mass was 1000 kg. Determine the magnitude of the force required to accelerate the object in kN.
The magnitude of the force required to accelerate the object is 70,000 kN.
In this problem, it is known that a UAP (unidentified aerial phenomena) was spotted with an acceleration vector of [tex]a = 20i +30j - 60k[/tex] in [tex]m/s^2[/tex] and the estimated mass was 1000 kg.
We need to determine the magnitude of the force required to accelerate the object in kN.
Magnitude of force (F) can be calculated by the following formula:
F = ma
Where, m = mass of the object
a = acceleration of the object
So, [tex]F = ma = 1000\ kg \times 20i +30j - 60k m/s^2[/tex]
Now, we will calculate the magnitude of force.
So, [tex]|F| = \sqrt {F^2} = \sqrt{(1000 kg)^2(20i +30j} - 60k m/s^2)^2\\|F| = 1000 \times \sqrt{(400 + 900 + 3600)} kN\\|F| = 1000 \times \sqrt {4900} kN\\|F| = 1000\times 70 kN\\|F| = 70,000 kN[/tex]
Therefore, the magnitude of the force required to accelerate the object is 70,000 kN.
To know more about acceleration, visit:
https://brainly.com/question/2303856
#SPJ11
Temperature sensitive medication is stored in a refrigerated compartment maintained at -10°C. The medication is contained in a long thick walled cylindrical vessel of inner and outer radii 24 mm and 78 mm, respectively. For optimal storage, the inner wall of the vessel should be 6°C. To achieve this, the engineer decided to wrap a thin electric heater around the outer surface of the cylindrical vessel and maintain the heater temperature at 25°C. If the convective heat transfer coefficient on the outer surface of the heater is 100W/m².K., the contact resistance between the heater and the storage vessel is 0.01 m.K/W, and the thermal conductivity of the storage container material is 10 W/m.K., calculate the heater power per length of the storage vessel. (b) A 0.22 m thick large flat plate electric bus-bar generates heat uniformly at a rate of 0.4 MW/m² due to current flow. The bus-bar is well insulated on the back and the front is exposed to the surroundings at 85°C. The thermal conductivity of the bus-bar material is 40 W/m.K and the heat transfer coefficient between the bar and the surroundings is 450 W/m².K. Calculate the maximum temperature in the bus-bar. 2. A design engineer is contemplating using internal flow or external flow to cool a pipe maintained at 122 °C. The options are to use air at 32 °C in cross flow over the tube at a velocity of 30 m/s. The other option is to use air at 32 °C through the tube with a mean velocity of 30 m/s. The tube is thin-walled with a nominal diameter of 50 mm and flow conditions inside the tube is assumed fully developed. Calculate the heat flux from the tube to the air for the two cases. What would be your advice to the engineer? Explain your reason. For external flow over the pipe in cross-flow conditions: 5/874/3 Nup = 0.3+ 1+ 0.62 Reb/2 Pul/3 [1+(0.4/732187441 ! Red 282.000 For fully developed internal flow conditions: Nup = 0.023 Re45 P0.4
The heater power per length of the storage vessel can be calculated using the formula:
Heater power per length = (Temperature difference) / [(Thermal resistance of contact) + (Thermal resistance of convection)]
In this case, the temperature difference is the difference between the heater temperature (25°C) and the desired inner wall temperature (6°C), which is 19°C.
The thermal resistance of contact is given as 0.01 m.K/W and the thermal resistance of convection can be calculated using the formula:
Thermal resistance of convection = 1 / (Heat transfer coefficient × Outer surface area)
The outer surface area of the cylindrical vessel can be calculated using the formula:
Outer surface area = 2π × Length × Outer radius
Substituting the given values, we can calculate the thermal resistance of convection.
Once we have the thermal resistance of contact and the thermal resistance of convection, we can substitute these values along with the temperature difference into the formula to calculate the heater power per length of the storage vessel.
b) The maximum temperature in the bus-bar can be calculated using the formula:
Maximum temperature = Front surface temperature + (Heat generation rate / (Heat transfer coefficient × Surface area))
In this case, the front surface temperature is 85°C, the heat generation rate is 0.4 MW/m², the heat transfer coefficient is 450 W/m².K, and the surface area can be calculated using the formula:
Surface area = Length × Width
Substituting the given values, we can calculate the maximum temperature in the bus-bar.
2) To calculate the heat flux from the tube to the air for the two cases, we can use the Nusselt number correlations for external flow over the pipe in cross-flow conditions and fully developed internal flow conditions.
For external flow over the pipe in cross-flow conditions, the Nusselt number correlation is given as:
Nup = 0.3 + 1 + 0.62(Reb/2)(Pul/3)[1 + (0.4/732187441 × Red^282)]
For fully developed internal flow conditions, the Nusselt number correlation is given as:
Nup = 0.023 × Re^0.8 × Pr^0.4
In both cases, the heat flux can be calculated using the formula:
Heat flux = Nusselt number × (Thermal conductivity / Diameter)
Substituting the given values and using the Nusselt number correlations, we can calculate the heat flux for the two cases.
My advice to the engineer would depend on the heat flux values calculated. The engineer should choose the option that provides a higher heat flux, as this indicates a more efficient cooling process. If the heat flux is higher for external flow over the pipe in cross-flow conditions, then the engineer should choose this option. However, if the heat flux is higher for fully developed internal flow conditions, then the engineer should choose this option.
Know more about Thermal resistance here:
https://brainly.com/question/33634341
#SPJ11
4. (2 pts) Heating under reflux requires the use of a condenser (typically a water-cooled condenser). What is the function of the condenser? What might happen if the condenser is not used?
In summary, the condenser plays a crucial role in heating under reflux by allowing the collection and return of vapors to the reaction mixture, preventing the loss of volatile substances and maintaining a controlled environment.
The function of a condenser in heating under reflux is to cool the vapors generated during the heating process and condense them back into a liquid form. The condenser helps maintain a closed system and prevents the loss of volatile substances or solvents. If the condenser is not used during heating under reflux:
Loss of volatile substances: Without the condenser, volatile components in the mixture could evaporate and escape into the surrounding environment. This would result in a loss of the desired substances and could affect the outcome of the reaction or separation process.
Loss of solvent: If the mixture being heated contains a solvent, the absence of a condenser could lead to the evaporation of the solvent, resulting in a change in the concentration and composition of the solution.
Safety hazards: Some substances or solvents used in reactions under reflux may be flammable, toxic, or harmful when inhaled. The condenser helps prevent the release of these substances into the air, reducing the risk of fire or exposure to hazardous fumes.
To know more about condenser,
https://brainly.com/question/14568643
#SPJ11
What is the combination of ground
improvement theory / technique being emphasised as the most
effective in this large scale land reclamation project in view of
the underlying soil profiles?
The combination of ground improvement theory/ technique being emphasized as the most effective in a large scale land reclamation project in view of the underlying soil profiles is vertical drains with preloading, surcharge, or vacuum consolidation.
To address this issue of a weak soil profile for land reclamation, various ground improvement techniques have been developed.
The purpose of these techniques is to improve the soil's engineering properties by increasing its strength, reducing its compressibility, and increasing its bearing capacity. The most common soil improvement methods are deep mixing, dynamic compaction, surcharge preloading, vertical drains with preloading, and vacuum consolidation.
The soil's permeability and compressibility play an important role in determining the ground improvement technique to be used.
Vertical drains with preloading, surcharge, or vacuum consolidation is the most effective ground improvement technique for this large scale land reclamation project in view of the underlying soil profiles.
The use of vertical drains with preloading is a well-established and commonly used technique for reducing the time required for surcharge consolidation and improving the efficiency of land reclamation.
The use of vacuum consolidation is also effective in improving the soil's compressibility.
To know more about permeability, visit:
https://brainly.com/question/32482559
#SPJ11
In the following spherical pressure vessle, the pressure is 45 ksi, outer radious is 22 in. and wall thickness is 1 in, calculate: 1. Lateral 01 and longitudinal a2 normal stress 2. In-plane(2D) and out of plane (3D) maximum shearing stress.
2D maximum shearing stress is 495 ksi and 3D maximum shearing stress is 1976.9 ksi.
Given,Pressure = 45 ksi
Outer radius = 22 in
Wall thickness = 1 in
The formula for Lateral (01) normal stress is
σ01 = Pr / t
Where,
σ01 = Lateral (01) normal stress
P = Internal Pressure = 45 ksi (Given)
r = Outer radius = 22 in.
t = Wall thickness = 1 in
Substitute the given values,
σ01 = Pr / t
= 45 × 22 / 1
= 990 ksi
The formula for Longitudinal (a2) normal stress is
σa2 = Pr / 2t
Where,σa2 = Longitudinal (a2) normal stress
P = Internal Pressure = 45 ksi (Given)
r = Outer radius = 22 in.
t = Wall thickness = 1 in
Substitute the given values,
σa2 = Pr / 2t
= 45 × 22 / (2 × 1)
= 495 ksi
Therefore, Lateral (01) normal stress is 990 ksi and Longitudinal (a2) normal stress is 495 ksi.
2D maximum shearing stress can be given as
τ2D = σ01 / 2
Where,
τ2D = In-plane maximum shearing stress
σ01 = Lateral (01) normal stress = 990 ksi (Calculated in step 1)
Substitute the given values,
τ2D = σ01 / 2
= 990 / 2
= 495 ksi
3D maximum shearing stress can be given as
τ3D = (σa2^2 + 3σ01^2)1/2 / 2
Where,
τ3D = Out of plane maximum shearing stress
σa2 = Longitudinal (a2) normal stress = 495 ksi (Calculated in step 1)
σ01 = Lateral (01) normal stress = 990 ksi (Calculated in step 1)
Substitute the given values,
τ3D = (σa2^2 + 3σ01^2)1/2 / 2
= (495^2 + 3 × 990^2)1/2 / 2
= 1976.9 ksi
Therefore, 2D maximum shearing stress is 495 ksi and 3D maximum shearing stress is 1976.9 ksi.
To know more about stress visit:
https://brainly.com/question/31366817
#SPJ11
Next Problem A road perpendicular to a highway leads to a farmhouse located 10 mile away. An automobile traveling on the highway passes through this intersection at a speed of 70mph. How fast is the distance between the automobile and the farmhouse increasing when the automobile is 7 miles past the intersection of the highway and the road? The distance between the automobile and the farmhouse is increasing at a rate of !!!miles per hour. Next Problem A conical water tank with vertex down has a radius of 11 feet at the top and is 23 feet high. If water flows into the tank at a rate of 10 ft³/min, how fast is the depth of the water increasing when the water is 13 feet deep? The depth of the water is increasing at ft/min. Previous Problem Problem List Next Problem The demand function for a certain item is Q=p²e-(P+4) Remember elasticity is given by the equation E = -40P dp Find E as a function of p. E= ⠀⠀
The distance between the automobile and the farmhouse is increasing at a rate of approximately 19.2 miles per hour when the automobile is 7 miles past the intersection of the highway and the road.
Determining the rate on increaseLet x and y be the distance the automobile has traveled along the highway from the intersection, and the distance between the automobile and the farmhouse, respectively.
When the automobile is 7 miles past the intersection, we have x = 7. find the rate of change of y, or dy/dt, at this instant.
Use Pythagorean theorem to relate x and y:
[tex]y^2 = 10^2 + x^2[/tex]
Differentiate both sides with respect to t
[tex]2y (dy/dt) = 0 + 2x (dx/dt)\\dy/dt = (x/y) (dx/dt)[/tex]
[tex]y^2 = 10^2 + 7^2 = 149\\y = \sqrt(149) \approx 12.2 miles.[/tex]
To find dx/dt, differentiate x with respect to time.
Since the automobile is traveling at a constant speed of 70 mph
dx/dt = 70 mph.
Substitute the values
[tex]dy/dt = (x/y) (dx/dt)\\= (7/\sqrt(149)) (70) \approx 19.2 mph[/tex]
Hence, the distance between the automobile and the farmhouse is increasing at a rate of approximately 19.2 miles per hour when the automobile is 7 miles past the intersection of the highway and the road.
Learn more on rate of increase on https://brainly.com/question/12614336
#SPJ4
In a survey it was found that 21 persons liked product A, 26 liked product B and 29 liked product C. If 14 people liked products A and B, 12 people liked products C and A, 14 people liked products B and C and 8 liked all the three products. Find
a) The number of people who liked at least one product
Answer:
64
Step-by-step explanation:
To find the number of people who liked at least one product, we need to calculate the total number of unique individuals who liked any of the three products.
We can use the principle of inclusion-exclusion to solve this problem. The principle states that:
|A ∪ B ∪ C| = |A| + |B| + |C| - |A ∩ B| - |A ∩ C| - |B ∩ C| + |A ∩ B ∩ C|
Given:
|A| = 21 (number of people who liked product A)
|B| = 26 (number of people who liked product B)
|C| = 29 (number of people who liked product C)
|A ∩ B| = 14 (number of people who liked products A and B)
|A ∩ C| = 12 (number of people who liked products A and C)
|B ∩ C| = 14 (number of people who liked products B and C)
|A ∩ B ∩ C| = 8 (number of people who liked all three products)
Using the formula, we can calculate the number of people who liked at least one product:
|A ∪ B ∪ C| = 21 + 26 + 29 - 14 - 12 - 14 + 8
= 64
Therefore, the number of people who liked at least one product is 64.