how much work (in j ) is involved in a chemical reaction if the volume decreases from 4.10 to 1.12 l against a constant pressure of 0.801 atm ? express your answer to three significant figures and include the appropriate units.

The final state of the hydrogen atom is the n=2 energy level.

The initial state of the hydrogen atom is the ground state, where the electron is in the n=1 energy level. When it absorbs a photon of wavelength 93.73 nm, it jumps to a higher energy level. We can calculate the energy of the absorbed photon using the equation E = hc/λ, where h is Planck's constant, c is the speed of light, and λ is the wavelength of the photon.

E = (6.626 x 10^-34 J s)(2.998 x 10^8 m/s) / (93.73 x 10^-9 m) = 1.653 x 10^-18 J

This energy corresponds to the difference in energy between the ground state and some higher energy level, which we can calculate using the Rydberg equation:

1/λ = R_H(1/n_i^2 - 1/n_f^2)

where λ is the wavelength of the emitted photon, R_H is the Rydberg constant for hydrogen, and n_i and n_f are the initial and final energy levels, respectively. We know λ and R_H, and we can assume n_i = 1, so we can solve for n_f:

1/λ = R_H(1 - 1/n_f^2)

n_f^2 = 1 / (1 - λ/R_H) = 4

n_f = 2

To know more about hydrogen, here

brainly.com/question/28494990

#SPJ4

The solubility of AgCl in the given solution is 1.26 x 10⁻⁸ M.

The reaction is,

AgCl(s) ⇌ Ag⁺(aq) + Cl⁻(aq)

Ksp = [Ag⁺][Cl⁻] = 1.61 x 10⁻¹⁰

SrCl₂ dissociates as follows:

SrCl₂(s) ⇌ Sr²⁺(aq) + 2Cl⁻(aq)

Since the reaction between AgCl and SrCl₂ does not involve the Sr²⁺ ion, its concentration can be considered constant and omitted from the equilibrium expression.

The solubility of AgCl in a solution of 3.42 x 10⁻⁴ M SrCl₂ is given by the following equation:

Ksp = [Ag⁺][Cl⁻] = x(2x + 3.42 x 10⁻⁴)

where x is the molar solubility of AgCl.

Solving for x,

x = 1.26 x 10⁻⁸ M

To know more about solubility, here

brainly.com/question/28044392

#SPJ4

The molar mass corresponds to the chlorofluorocarbon CF3Cl (Freon-11), which has a molar mass of 137.37 g/mol. Therefore, the chlorofluorocarbon in the experiment is CF3Cl.

The rate of effusion of a gas through a porous barrier is inversely proportional to the square root of its molar mass. Therefore, we can use the rate of effusion to determine the relative molar mass of the two gases and identify which one is a chlorofluorocarbon.

The rate of effusion can be calculated using Graham's law:

Rate of effusion = Volume of gas / Time taken to effuse

For the chlorofluorocarbon, the rate of effusion is:

Rate of effusion (CFC) = 50 mL / 157 s = 0.3185 mL/s

For argon, the rate of effusion is:

Rate of effusion (Ar) = 50 mL / 76 s = 0.6579 mL/s

Using Graham's law, we can set up the following equation:

Rate of effusion (CFC) / Rate of effusion (Ar) = sqrt(Molar mass (Ar) / Molar mass (CFC))

Solving for the ratio of molar masses:

Molar mass (Ar) / Molar mass (CFC) = (Rate of effusion (Ar) / Rate of effusion (CFC))^2

Molar mass (Ar) / Molar mass (CFC) = (0.6579 mL/s / 0.3185 mL/s)^2

Molar mass (Ar) / Molar mass (CFC) = 4.294

Molar mass (CFC) = Molar mass (Ar) / 4.294

The molar mass of argon is 39.95 g/mol. Therefore, the molar mass of chlorofluorocarbon is:

Molar mass (CFC) = 39.95 g/mol / 4.294 = 9.30 g/mol

To learn more about molar mass

https://brainly.com/question/13152455

#SPJ4

The balanced molecular equation when nitrosyl chloride gas, NOCI, is heated to produce gaseous chlorine and nitrogen monoxide is:

2NOCl(g) ⇔ Cl₂(g) + 2NO(g)

Chemical equation is simply a ritrogen monoxide epresentation of chemical reactions using the symbols and formula of elements. We must understand, that every reaction has two sides i.e reactants and products.

The balancing of chemical equation must obey the law of conservation of matter other wise, atoms will either be created or destroyed during the reaction.

Now we shall write the balanced molecular equation for the reaction invoving the heating of nitrosyl chloride gas, NOCI. Details below:

Nitrosyl chloride gas ⇔ Gaseous chlorine + Nitrogen monoxide

NOCl(g) ⇔ Cl₂(g) + NO(g)

There are 2 atoms of Cl on the right and 1 atom on the left. It can be balanced by writing 2 before NOCl as shown below:

2NOCl(g) ⇔ Cl₂(g) + NO(g)

There are 2 atoms of N on the left and 1 atom on the right. It can be balanced by writing 2 before NO as shown below:

2NOCl(g) ⇔ Cl₂(g) + 2NO(g)

Thus, the equation is balanced.

Learn more about balancing equation:

https://brainly.com/question/12192253

#SPJ1

To make 50.0 mL of a 0.100 M ammonia buffer with a pH of 9.25, we need to mix 50.0 mL of 1.00 M ammonia and 50.0 mL of 1.00 M HCl.

To make a buffer solution, we need to mix a weak base and its conjugate acid in the appropriate amounts. In this case, we want to make an ammonia buffer with a pH of approximately 9.25, which is close to the pKa of ammonia (9.25). Henderson-Hasselbalch equation for buffer will be;

pH = pKa + log([A⁻]/[HA])

where [A⁻] is the concentration of the conjugate base (ammonia in this case) and [HA] is the concentration of the weak acid (ammonium ion in this case). We are given that the final buffer solution has a pH of 9.25 and a concentration of 0.100 M.

Calculating the moles of ammonia and ammonium ion needed

pH = pKa + log([A⁻]/[HA])

9.25 = 9.25 + log([A⁻]/[HA])

log([A⁻]/[HA]) = 0

[A⁻]/[HA] = 1

[HA] = [A⁻] = 0.050 M (half the final concentration)

So, we need 0.050 moles of ammonia and 0.050 moles of ammonium ion in the final solution.

Calculating the volume of 1.00 M ammonia needed

0.050 moles = 1.00 M x V

V = 0.050 L = 50.0 mL

So, we need 50.0 mL of 1.00 M ammonia.

Calculating the volume of 1.00 M HCl needed

We can use the equation;

moles of HCl = moles of NH₃ = 0.050

The molarity of HCl can be calculated using the equation;

Molarity = moles of solute/volume of solution (in liters)

0.050 moles / volume = 1.00 M

volume = 0.050 L = 50.0 mL

So, we need 50.0 mL of 1.00 M HCl.

To Know more about buffer solution here

https://brainly.com/question/15709146

#SPJ4

The term absorbance is directly proportional to the concentration (c) of the solution which is used in the experiment of the spectra.

The absorbance is defined as the term which is said to be directly proportional to the length of the light path that is equal to the width of the cuvette. The relationship between concentration and absorbance can be explained by the Beer-Lambert law. This law relates the attenuation of light to the properties of a material. The Beer-Lambert law is defined as the law which states that the concentration of a chemical solution is directly proportional to its absorption of light.

The acid dissociation constants were determined in the spectra will be 2.97 pKa* and 9.47 pKa. The pKa and pKa* values are corresponded well with literature values of 9.45 and 3.0 with a 0.2 and 1.0% difference, respectively. This was determined that 2-naphthol is a weaker acid in the ground state than the excited state due to the value of  pKa > pKa.

To learn more about  absorbance

https://brainly.com/question/14919298

#SPJ4

Answer: The heat capacity of a bomb calorimeter is 500 J°C.

In the following chemical reaction, the solution was supplemented with 8.01g of magnesium sulfate.

We must utilize the following chemical formula to determine how magnesium sulfate and sodium hydroxide react to solve this issue:

MgSO4 + 2 NaOH → Mg(OH)2 + Na2SO4

One mole of magnesium sulfate (MgSO4) interacts with two moles of sodium hydroxide (NaOH), resulting in one mole of magnesium hydroxide (Mg(OH)2) and one mole of sodium sulfate, according to the equation (Na2SO4).

We must utilize the solution's concentration and volume to determine how many moles of NaOH are present in the solution:

C = n/V

where n is the number of moles, V is the volume in liters, and C is the concentration in moles per liter.

n(NaOH) = C × V

               = 1 mol/L × 0.133 L  

               = 0.133 mol.

We require half as many moles of MgSO4 as we do of NaOH since their mole ratio is 1:2:

n(MgSO4) = 0.5 × n(NaOH)

                 = 0.5 × 0.133 mol

                 = 0.0665 mol

Using its molar mass, we can finally translate the quantity of MgSO4 from moles to grams:

m(MgSO4) = n(MgSO4) × M(MgSO4)

                  = 0.0665 mol × 120.4 g/mol = 8.01 g

Therefore the solution was supplemented with 8.01g of magnesium sulfate.

To learn more about chemical reactions, refer to:

https://brainly.com/question/11231920

#SPJ4

The presence of small of quantity of hydrochloric acid inside the samples of tert-butyl chloride, is attributed to 2 motives: 1. As an impurity in the course of the synthesis of tert-butyl chloride from tert-butyl alcohol and hydrochloric acid. 2. because of the hydrolysis of tert-butyl chloride.

Hydrolysis is a chemical reaction that involves the breaking of a chemical bond in a molecule through the addition of water molecules. This process results in the formation of two or more new molecules. Hydrolysis is an important process in many biological systems, including digestion, where enzymes help break down large molecules such as proteins, carbohydrates, and fats into smaller molecules that can be absorbed and used by the body.

In hydrolysis, water molecules are used to break the bonds between the atoms in the original molecule. One part of the original molecule will gain a hydrogen ion (H+) from the water, while the other part will gain a hydroxide ion (OH-). This process can occur naturally or with the help of enzymes, which are biological catalysts that speed up chemical reactions in living organisms.

To learn more about Hydrolysis visit here:

brainly.com/question/29439050

#SPJ4

Complete Question:-

In the introduction to this experiment, the text states that small amounts of HCl are present in samples of tert-butyl chloride. Write an arrow-pushing mechanism that explains the source of the HCl.

Answer:

Holding

Explanation:

keeping the item means to hold the item

Holding. Holding involves keeping the item for a short amount of time before moving it elsewhere.

While loading and unloading involve the act of adding objects to a truck or container, holding refers to the act of maintaining an item for a brief period of time before transporting it to another location.

Retaining something enables for a little interval of time to pass before it is transferred to another location.

When awaiting the arrival of a transport truck, verifying the item for damage, doing quality control checks, or arranging with other employees or departments before the item may be moved, it may be required to hold the item. When the next stage of the process is delayed or the receiving area is not readily accessible, it might also be necessary.

To know more about the holding visit:

https://brainly.com/question/29559299

#SPJ1

The new volume of the gas at 26.8°C and 742 mmHg is approximately 4.28 L.

To find the new volume of the gas at the given temperature and pressure, we can use the combined gas law formula:

P1 × V1 / T1 = P2 × V2 / T2

where P1 is the initial pressure, V1 is the initial volume, T1 is the initial temperature in Kelvin, P2 is the final pressure, T2 is the final temperature in Kelvin, and V2 is the final volume.

Convert the temperatures to Kelvin.
T1 = 25.6°C + 273.15 = 298.75 K
T2 = 26.8°C + 273.15 = 299.95 K

Convert the pressures to atm.
P1 = 748 mmHg × (1 atm / 760 mmHg) = 0.98421 atm
P2 = 742 mmHg × (1 atm / 760 mmHg) = 0.97632 atm

Rearrange the combined gas law formula to solve for V2.
V2 = P1 × V1 × T2 / (T1 × P2)

Substitute the given values into the formula.
V2 = (0.98421 atm) × (4.25 L) × (299.95 K) / (298.75 K × 0.97632 atm)

Calculate the final volume, V2.
V2 ≈ 4.28 L

The volume of the gas at 26.8°C and 742 mmHg is approximately 4.28 L.

More on gas volume: https://brainly.com/question/29490815

#SPJ11

From a ph meter titration curve a student experimentally determines the pka of benzoic acid to be 4.06. the experimental ka for benzoic acid is  approximately [tex]8.72[/tex] × [tex]10^{-5}[/tex]

To calculate the experimental Ka for benzoic acid, you can use the relationship between Ka and pKa:

pKa = -log(Ka).

In this case, the student determined the pKa to be 4.06.
To find the Ka, you need to use the inverse of the log function, which is [tex]10 ^{-pKa}[/tex].

So, Ka = [tex]10^{-4.06}[/tex]
Ka  ≈ [tex]8.72[/tex] × [tex]10^{-5}[/tex]
The experimental Ka for benzoic acid is approximately [tex]8.72[/tex] × [tex]10^{-5}[/tex]

A titration curve is a graph that shows the pH of a solution as a function of the amount of titrant applied.

It is used to calculate the equivalence point, which is the point at which the amount of titrant administered is stoichiometrically equivalent to the amount of analyte in the solution being tested.

For more such questions on  titration curve, click on:

https://brainly.com/question/16749233

#SPJ11

the minimum mass of Mg(NO₃)₂ required to begin precipitation of MgF₂ is 6.37 × 10⁻³ g/L.

The balanced equation for the precipitation of MgF₂ from Mg(NO₃)₂ and HF is:

Mg(NO₃)₂ + 2HF → MgF₂(s) + 2HNO₃

The concentration of fluoride ions can be found using the equilibrium expression for the dissociation of HF:

HF + H₂O ⇌ H₃O⁺ + F⁻

Ka = [H₃O⁺][F⁻]/[HF]

Since the initial concentration of HF is 0.560 M, the concentration of [H₃O⁺] is negligible compared to [HF] because HF is a weak acid. Therefore, we can simplify the expression to:

Ka = [F⁻][HF]/[HF] = [F⁻]

[F⁻] = Ka = 7.2 × 10⁻⁴ M

Now we need to determine the minimum amount of Mg(NO₃)₂ required to provide enough fluoride ions to reach the saturation point of MgF₂.

Let's assume x moles of Mg(NO₃)₂ is added to 1.00 L of 0.560 M HF solution. This will result in the addition of 2x moles of F⁻ ions to the solution.

The molar solubility of MgF₂ is equal to the square root of Ksp because the stoichiometric coefficients are 1 for both MgF₂ and Mg(NO₃)₂.

Molar solubility of MgF₂ = sqrt(Ksp) = sqrt(7.4 × 10⁻⁹) = 8.6 × 10⁻⁵ M

To reach saturation, the concentration of F⁻ ions must be equal to the molar solubility of MgF₂. Therefore:

[F⁻] = 8.6 × 10⁻⁵ M = 2x moles/L

x = 4.3 × 10⁻⁵ moles/L

The mass of Mg(NO₃)₂ required is then:

mass = moles × molar mass = (4.3 × 10⁻⁵ mol/L) × (148.3 g/mol) = 6.37 × 10⁻³ g/L.

Learn more about concentration here:

https://brainly.com/question/10725862

#SPJ1

90.0 g of ethene is provided, which is more than the 14.025 g needed to react with 1.5 moles of oxygen in this reaction. There will therefore be some ethene left over once the reaction is finished.

In the process of respiration, six oxygen molecules combine with one glucose molecule to generate six carbon dioxide and water molecules. Equation: C6H12O6 + 6O2 6CO2 + 6H2O + Energy can be used to represent the respiration reaction.

To calculate the amount of ethene required to react with 1.5 moles of O2, we can now utilise stoichiometry:

3 moles of oxygen and 1 mole of ethene react.

1.5 moles of oxygen will react with (1/3) x 1.5 moles of ethene = 0.5 moles of ethene

Then, we can figure out how much 0.5 moles of ethene weigh:

m(ethene) = n(ethene) x Molar mass(ethene)

m(ethene) = 0.5 mol x 28.05 g/mol

m(ethene) = 14.025 g

To know more about reaction visit:-

https://brainly.com/question/28984750

#SPJ1

To calculate the age of the rock using the radioactive isotope, we can use the formula. Whereas the age of the rock would be approximately 696.579 million years.

t = (t1/2) * log(base 2) (N0/N) Where:

t = age of the rock

t1/2 = half-life of the isotope

N0 = initial number of parent particles

N = current number of parent particles

Given that the half-life of the isotope is 300 million years, we can substitute t1/2 = 300 million years into the formula.

Also, the ratio of parent to daughter particles is 1/4, which means that for every 1 parent particle, there are 4 daughter particles. This also means that the total number of particles (parent + daughter) is 5.

Let's assume that we started with N0 parent particles. Then, the number of daughter particles would be 4N0. Therefore, the total number of particles N would be N0 + 4N0 = 5N0.

Since the ratio of parent to daughter particles is currently 1/4, the current number of parent particles is 1/5 of the total number of particles, which is (1/5)*N.

Substituting all these values into the formula, we get:

t = (300 million years) * log(base 2) (N0 / (1/5)*N0)

Simplifying the expression inside the logarithm, we get:

t = (300 million years) * log(base 2) 5

Using a calculator, we can evaluate log(base 2) 5 to be approximately 2.32193.

Substituting this value into the formula, we get:

t = (300 million years) * 2.32193

t = 696.579 million years

Therefore, the age of the rock is approximately 696.579 million years.

Learn more about Radioactive isotope here:

brainly.com/question/28039996

#SPJ4

A solutions that is highly reactive & consists ions— molecules or atoms that also have received or exchanged electrons—is an electrolyte solution.

Since the final cost on I equal the net cost on (ii), the electrolytic mixture is always neutral (iii). Unlike with the superconductor, the sodium chloride conducts the electrical charge by virtue of progression of its (iv). The characteristic that causes a metal to prefer to dissolve in positive charge is defined as (v).

Substances known as electrolytes show a natural positive or negative static electricity when submerged in water. Several body activities are supported by them, including controlling nuclear reactions or preserving overall proportion of liquids both inside and outside your cells.

To know more about electrons visit:

https://brainly.com/question/28977387

#SPJ1

The pulmonary diffusion capacity of carbon monoxide (DLCO) is used to determine the transfer of gases through the lungs. The amount of carbon monoxide absorbed by hemoglobin in the lungs is measured in this method.

Carbon monoxide has a higher diffusion coefficient than oxygen, and it is 20-30 times more soluble than oxygen. These differences affect the interpretation of DLCO results. Hemoglobin is a molecule that is critical in the transportation of oxygen and carbon monoxide. Hemoglobin is known to bind with carbon monoxide 240 times more readily than oxygen. In this method, hemoglobin plays a critical role. It is assumed that 100 percent of inhaled carbon monoxide is absorbed into the bloodstream and that the hemoglobin-CO complex forms reversible binding without causing an alteration in the blood's oxygenation level.

The DLCO measurement is based on the following assumptions: At sea level, the concentration of carbon monoxide is zero in the blood being analyzed. The solubility of carbon monoxide in blood is 20-30 times greater than that of oxygen, indicating that it is dissolved in the blood more easily. The alveolar-capillary barrier's thickness is consistent throughout the lung's entire surface area. The diffusion capacity is determined solely by the exchange of gases through the alveolar-capillary membrane and the available hemoglobin in the blood.

Learn more about carbon monoxide at  brainly.com/question/22530423

#SPJ11

The steep-rise interval in the weak acid-strong base curve is more pronounced than in the strong acid-strong base curve because the weak acid requires more titrant to be neutralized than the strong acid, so the pH changes more slowly initially.

A. The initial pH for the weak acid-strong base curve is higher than the initial pH for the strong acid-strong base curve.

This statement is inaccurate. In fact, the initial pH for the weak acid-strong base curve is lower than the initial pH for the strong acid-strong base curve. This is because a weak acid has a higher initial pH than a strong acid due to the lower concentration of H+ ions in solution.

B. At the equivalence points, the pH of the weak acid-strong base is greater than the pH of the strong acid-strong base.

This statement is accurate. At the equivalence point of a weak acid-strong base titration, the pH is greater than 7 due to the presence of the conjugate base of the weak acid in solution. At the equivalence point of a strong acid-strong base titration, the pH is 7.

C. At the half-equivalence points, the pH of the weak acid-strong base is greater than the pH of the strong acid-strong base.

This statement is accurate. At the half-equivalence point of a weak acid-strong base titration, the pH is greater than 7 because the solution contains both the weak acid and its conjugate base. At the half-equivalence point of a strong acid-strong base titration, the pH is 7.

D. The steep-rise interval in the weak acid-strong base curve is more pronounced than in the strong acid-strong base curve.

Learn more about concentration here:

https://brainly.com/question/13872928

#SPJ1

According to the Brønsted-Lowry model, an acid and its conjugate base differ by a single proton, while a base and its conjugate acid differ by the addition of a single proton. If a reaction produces conjugate acid-base pairs, it supports this model.

To determine if the reaction supports the Brønsted-Lowry model of acids and bases, there are several questions that could be asked. Two possible questions are:

1. Does the reaction involve the transfer of protons (H+ ions) from one molecule to another.This is a key concept in the Brønsted-Lowry model, which defines acids as proton donors and bases as proton acceptors. If a reaction involves the transfer of protons, it supports this model.

2. Do the reactants and products contain conjugate acid-base pairs.

for more such questions on Brønsted-Lowry model :

https://brainly.com/question/20308475

#SPJ11

Answer:

1. Did an acid donate a hydrogen ion to become a conjugate base?

2. Did a base accept a hydrogen ion to become a conjugate acid?

Total 12 electrons are transferred in the reaction.

In the above reaction, the oxidation state of chlorine changes from +7 to +3. To determine the number of electrons transferred, we need to calculate the change in oxidation state of chlorine.

Each chlorate ion (ClO₄⁻) has a charge of -1, and each chlorite ion (ClO₃⁻) has a charge of -1 as well.

The oxidation state of oxygen is -2, so the oxidation state of the four oxygen atoms in the chlorate ion is -8, and the oxidation state of the three oxygen atoms in the chlorite ion is -6.

Let x be the oxidation state of chlorine in the chlorate ion, then we have;

x + 4(-2) = -1

x = +7

Let y be the oxidation state of chlorine in the chlorite ion, then we have;

y + 3(-2) = -1

y = +5

Therefore, each chlorine atom undergoes a reduction of 2 units, which corresponds to the gain of 2 electrons.

Since there are 6 chlorine atoms in total (3 in chlorate and 3 in chlorite), the total number of electrons transferred in the reaction is;

6 x 2 = 12 electrons.

To know more about oxidation state here

https://brainly.com/question/11313964

#SPJ4

A common example of a solution is saltwater. In this solution, the solute is salt (NaCl) and the solvent is water (H2O).

When salt is added to water, it dissolves into the liquid to form a homogeneous mixture. The water molecules surround the ions of the salt and pull them apart from each other, resulting in the formation of individual salt ions dispersed throughout the water. The salt ions become evenly distributed throughout the water, resulting in a solution.

In this example, the salt (NaCl) is the solute because it is the substance that is being dissolved. The water (H2O) is the solvent because it is the substance that dissolves the salt and creates the solution.

To know more about homogeneous mixture, visit:

https://brainly.com/question/24898889

#SPJ1

When 2.24 mol NaOH and 1.20 mol [tex]CO2[/tex] are allowed to react, NaOH is the limiting reactant.

Let's try to figure out the limiting reactant of the reaction between NaOH and CO2 by using stoichiometry.

Stoichiometry is a branch of chemistry that deals with the calculation of quantities of reactants and products involved in a chemical reaction.

By using stoichiometry, we can calculate the limiting reactant of a reaction, which is the reactant that gets consumed entirely and determines the amount of product formed.

Limiting reactant calculation

[tex]NaOH + CO2 → Na2CO3 + H2O[/tex]

From the balanced chemical equation above, we can see that one mole of NaOH reacts with one mole of CO2 to produce one mole of Na2CO3 and one mole of H2O.

Using the mole ratio, we can calculate the number of moles of Na2CO3 that will be formed from 2.24 mol of NaOH.

[tex]2.24 mol NaOH × 1 mol Na2CO3/1 mol NaOH = 2.24 mol Na2CO3[/tex]

Similarly, we can calculate the number of moles of Na2CO3 that will be formed from 1.20 mol of CO2.1.20 mol CO2 × 1 mol Na2CO3/1 mol CO2 = 1.20 mol Na2CO3

Therefore, NaOH is the limiting reactant because it produces a smaller number of moles of Na2CO3 than CO2. NaOH is the limiting reactant, and we can say that 2.24 mol of NaOH reacts with 1.20 mol of CO2 to form 1.20 mol of Na2CO3.

To know more about limiting reagent refer to-

brainly.com/question/26905271#

#SPJ11

If I contain 3 moles of gas in a container with a volume of 60 liters and at a temperature of 400 K,The pressure inside the container is approximately 16.42 atm.

Using the Ideal Gas Law, we can calculate the pressure inside the container. The Ideal Gas Law is expressed as PV = nRT, where P is the pressure, V is the volume, n is the number of moles, R is the gas constant, and T is the temperature in Kelvin.

In this case, you have 3 moles of gas (n = 3), a volume of 60 liters (V = 60 L), and a temperature of 400 K (T = 400 K). The gas constant (R) for this equation is 8.314 J/(mol·K), but since we are using liters and atm, we need to use the value 0.0821 L·atm/(mol· K).

Now, we can plug the values into the equation:

P × 60 L = 3 mol × 0.0821 L·atm/(mol·K) × 400 K

To find the pressure (P), we will rearrange the equation and solve for P:

P = (3 mol × 0.0821 L·atm/(mol·K) × 400 K) / 60 L

P ≈ 16.42 atm

So, the pressure inside the container is approximately 16.42 atm.

Know more about  Ideal Gas Law here:

https://brainly.com/question/27870704

#SPJ11      

The transition state for the following SN2 reaction CI + NaSH ---> SH + NaCI is option III.

Transition state in a chemical reaction can be referred to as a molecular configuration that describes the point of maximum energy in the reaction path during which the bonds that are involved in the chemical reaction are in a state of change.

Transition state theory provides detailed explanations of the reaction rates and reaction mechanisms occurring in the gas phase.

The reaction mechanism in question is a substitution reaction in which the hydroxyl ion attacks the alkyl halide, resulting in the creation of an intermediate complex.

The complex is created in a transition state involving the transfer of a negatively charged ion, which will lead to a new bond forming with the incoming nucleophile.

In conclusion, the transition state for the following SN2 reaction CI + NaSH ---> SH + NaCI is option III.

To know more about transition state refer to-

brainly.com/question/30259181#

#SPJ11

Solution.

Henry's law states that the solubility of a gas in liquids at a constant temperature is proportional to its pressure. We write the formula:

�

=

�

×

�

S=K×P

The Henry's constant for each substance is individual, so we express it and find it through the solubility of the gas and its pressure.

�

=

�

�

K=

P

S

​

�

=

5.58

∗

1

0

−

6

K=5.58∗10

−6

And now we find the solubility of the gas at a different pressure.

S = 1.39 g/L

Answer:

S = 1.39 g/L

2.

Solution.

To begin with, we will translate the pressure from mm Hg of the column and from atmospheres to Pascals.

760 mmHg = 101324.72 Pa

2.5 atm = 253312.5 Pa

�

=

�

×

�

S=K×P

�

=

�

�

K=

P

S

​

�

=

1.58

∗

1

0

−

5

K=1.58∗10

−5

Now we find the solubility of the gas at a different pressure.

S = 4.00 g/L

Answer:

S = 4.00 g/L

3.

Solution.

To begin with, we will translate the pressure from atmospheres to Pascals.

0.750 atm = 75993.75 Pa

�

=

�

×

�

S=K×P

�

=

�

�

K=

P

S

​

�

=

3.22

∗

1

0

−

5

K=3.22∗10

−5

Now we find the gas pressure to get a solution with a concentration of 6.25 g / L.

�

=

�

�

P=

K

S

​

P = 194.1 kPa

Answer:

P = 194.1 kPa

The pH of the buffer will increase from 4.74 to 4.76 after adding 0.0020 mol of HCl. This increase in pH indicates that the buffer is able to resist the change in pH caused by the addition of an acid.

To determine the new pH of the buffer after adding 0.0020 mol of HCl, we need to use the Henderson-Hasselbalch equation, which relates the pH of a buffer to its acid dissociation constant (Ka) and the ratio of its conjugate base (A-) and acid (HA) concentrations. The equation is given as:

pH = pKa + log([A-]/[HA])

First, we need to determine the initial concentrations of CH3COOH and CH3COONa in the buffer solution. Since the buffer contains 0.50 M CH3COOH and 0.50 M CH3COONa, we can assume that the initial concentrations of CH3COOH and CH3COO- are both 0.50 M. We can then calculate the initial ratio of [CH3COO-]/[CH3COOH] as:

[CH3COO-]/[CH3COOH] = 0.50 M / 0.50 M = 1

Next, we need to determine the new concentrations of CH3COOH and CH3COO- after adding 0.0020 mol of HCl. Since the volume of the buffer is 100.0 mL or 0.100 L, the new concentration of CH3COOH ([HA]) can be calculated as:

[HA] = (0.50 M x 0.100 L) - 0.0020 mol = 0.0480 mol

Similarly, the new concentration of CH3COO- ([A-]) can be calculated as:

[A-] = (0.50 M x 0.100 L) + 0.0020 mol = 0.0520 mol

Now, we can calculate the new ratio of [CH3COO-]/[CH3COOH] as:

[CH3COO-]/[CH3COOH] = 0.0520 mol / 0.0480 mol = 1.083

Finally, we can use the Henderson-Hasselbalch equation to calculate the new pH of the buffer as:

pH = pKa + log([A-]/[HA])

pH = 4.74 + log(1.083)

pH = 4.76

For more such questions on pH

https://brainly.com/question/172153

#SPJ11

The statements about diels alder reaction which are true are given in the explanation part.

The following statements about the Diels-Alder reaction are true:

- True: It is a reaction involving pi-electrons.
- True: It is a concerted reaction, meaning that it occurs in a single step without the formation of reaction intermediates.
- False: It is not necessarily favored by entropy considerations, as the reaction can be endothermic and enthalpy-driven.
- True: It is a [4+2] cycloaddition, meaning that it involves the formation of a 6-membered ring from a 4-carbon diene and a 2-carbon dienophile.
- False: While some Diels-Alder reactions can be thermal, others require specific conditions such as high pressure or the use of a catalyst to occur.
To know more about diels alder reaction go through:-

https://brainly.com/question/21503302

#SPJ4