Answer:
9,000,000J
Explanation:
10kW is converted to Joules by multiplying 1000. Which is 10000W
15 minutes is converted to seconds, which is 900s
Energy transfer is Power(J) × Time(s)
so: 1000× 900
=9,000,000 J or 9000 kJ
Suppose the sphere is positively charged. Is it attracted to, repelled by, or not affected by the magnet?.
When a positively charged sphere is brought near the north pole of a magnet, the positively charged sphere will be attracted to the magnet.
Positively charged objectWhen a positively charged object is brought near the north pole of a magnet, the positively charged object will be attracted to the magnet beacuse of polarity.
Positively charged metals have the tendency to show the polarization of charges.
Thus, when a positively charged sphere is brought near the north pole of a magnet, the positively charged sphere will be attracted to the magnet. Also, if the south pole is brought near the sphere, the positively charged sphere will repel the magnet.
Learn more about attraction of magnet here: https://brainly.com/question/14749231
ball and bowl system
Answer:
Once the ball is place at the position A and then released, It will accelerate towards the mean position under its weight. At the mean piston it again maximum velocity and momentum so its moves up-to the position B due to inertia. At B it has zero velocity so zero kinetic energy but maximum potential energy.
Again from point B it will move towards O under the restoring Force having maximum velocity at O but does not stop at O due to inertia and will go up to A. In this way the ball will continue to oscillate between the points A and B about the point O, it has simple harmonic motion.
Explanation:
Iron has a density of 7.9 g/cm 3. What is the mass of a cube of iron with the length of one side equal to 55.0 mm
Answer:
1314362.5 gm or 1314.3625 kg
Explanation:
A cube has all three dimension =
55 * 55 * 55 = 166375 cm^3
166 375 * 7.9 g/ cm^3 = 1314362.5 gm
Immediately after it has started to rain, dust particles and oil residue float on the water and ____________ the traction of tires.
When it rains, dust particles and oil residues float on the water and this reduces the traction of tires.
What is traction?This concept refers to a force between the tires and road that causes the movement of the wheels or vehicle is slower.
What happens with traction when it rains?It is well-known more accidents occur when it rains, which is caused by cars slidding on the road. This is because when it rains traction or the grip of the wheel drastically reduces.
Learn more about traction in: https://brainly.com/question/14525337
Part B For this activity, you'll analyze the motion of the marked spot on the skateboarder's leg. For each dropdown labeled “cm” or “model cm,” change the option to “Legs.” In each frame containing a plot or table, you can use the buttons at the top of the frame to choose whether it shows a plot (graph) or a table. If it is showing a plot, you can select the y-axis label to choose which measurement to plot. See how to change the graph and table options. Now look at the graphs for the horizontal and vertical displacement of the legs against time. How do the two graphs, x vs. t and y vs. t appear? What can you say about the displacement of the snowboarder?
Answer:
Explanation:
c. By using the Select Data button and the Select Data Source optionExplanation:A scatter plot is a plot which is used to plot the points of the data on the horizontal and the vertical axis also it depicts how one variable is affected by the another. After preparing the scatter plot to enter the data in the scatter plot we need to use the data button and then data source option so that the data could be entered in the scatter plothence, option c is correct
The two graphs, x vs. t and y vs. t that are displacement vs time appear by using the Select Data button and the Select Data Source option.
What is Displacement?Displacement is defined as the change in position of an object. It is a vector quantity and has a direction and magnitude.
A scatter plot is a plot which is used to plot the points of the data on the horizontal and the vertical axis also it depicts how one variable displacement is affected by the another. After preparing the scatter plot to enter the data in the scatter plot we need to use the data button and then data source option so that the data could be entered in the scatter plot.
The two graphs, x vs. t and y vs. t that are displacement vs time appear by using the Select Data button and the Select Data Source option.
To learn more about displacement refer to the link:
brainly.com/question/11934397
#SPJ2
The dwarf planet Pluto was discovered in 1930. Since that time, which jovian planet has completed a full revolution around the Sun?
Answer:
Explanation:
Uranus takes about 84 years to circle the sun.
Pluto's existance has been known for 92 years. Uranius has completed 1 complete revolution. The numbers are reasonably close together and so Uranius is the answer.
A circular loop of wire 75 mm in radius carries a current of 113 A. Find the (a) magnetic field strength and (b) energy density at the center of the loop.
The magnetic field strength is 9.47 ×10⁻⁴ T
The energy density at the center of the loop is 0.36 J/m³
Calculating Magnetic field strength & Energy densityFrom the question, we are to find the magnetic field strength
The magnetic field strength of a loop can be calculated by using the formula,
[tex]B = \frac{\mu_{0} I}{2R}[/tex]
Where B is the magnetic field strength
[tex]\mu_{0}[/tex] is the permeability of free space [tex](\mu_{0}=4\pi \times 10^{-7} \ N/A^{2})[/tex]
[tex]I[/tex] is the current
and R is the radius
From the give information,
[tex]R = 75 \ mm= 75 \times 10^{-3} \ m[/tex]
and [tex]I = 113 \ A[/tex]
Putting the parameters into the formula, we get
[tex]B = \frac{4\pi \times 10^{-7} \times 113}{2 \times 75 \times 10^{-3} }[/tex]
[tex]B = 9.47 \times 10^{-4} \ T[/tex]
Hence, the magnetic field strength is 9.47 ×10⁻⁴ T
Now, for the energy density
Energy density can be calculated by using the formula,
[tex]u_{B} = \frac{B^{2} }{2\mu_{0} }[/tex]
Where [tex]u_{B}[/tex] is the energy density
Then,
[tex]u_{B}= \frac{(9.47\times 10^{-4} )^{2} }{2 \times 4\pi \times 10^{-7} }[/tex]
[tex]u_{B} = 0.36 \ J/m^{3}[/tex]
Hence, the energy density at the center of the loop is 0.36 J/m³
Learn more on Magnetic field stregth & Energy density here: https://brainly.com/question/13035557
One wave on a string is moving toward the right and another is moving toward the left. When they meet in the middle, half of the cycle of the wave from the right overlaps with half of the cycle of the wave from the left. The result is that the string gets flat when the two waves meet. What happened? What will happen after the waves meet?
When the wave meets the condition of interference occurs. The interference effect is the sum of the individual wave amplitudes at each site where more than one wave is present.
What is the interference of waves?The result of two or more wave trains flowing in opposite directions on a crossing or coinciding pathways. This phenomenon is known as the interference of waves.
When two wave pulses are traveling along a string toward each other. They meet and the phenomenon is occur known as interference.
Hence the phenomenon of interference occurs when two wave pulses are traveling along a string toward each other.
One wave on a string is moving toward the right and another is moving toward the left. When they meet in the middle, half of the cycle of the wave from the right overlaps with half of the cycle of the wave from the left.
The result is that the string gets flat when the two waves meet the condition of the interference of wave occurs.
Hence when the wave meets the condition of interference occurs.
To learn more about the interference of waves refer to the link;
brainly.com/question/16098226
#SPJ1
If you want to find stars that are just being born, where are the best places to search?.
Answer:
In giant molecular clouds
Explanation:
To find the stars that are just being born, one of the best places to search is giant molecular clouds.
What is a Star?An astronomical object known as a star is made up of a luminous plasma spheroid that is held together by gravity. The Sun is the star that is nearest to Earth. Other stars are also visible at night with the eye, but because of their great distances from Earth, they appear as stationary points of light.
Many of the brightest stars have names, and the most notable stars have been organized into constellations and asterisms. Star catalogs have been put out by astronomers that list the known stars and provide standardized stellar labels. An estimated 10²²–10²⁴ stars are alive in the observable cosmos.
These stars are all situated within the Milky Way galaxy, with only 4,000 of them being visible with the unaided eye.
To know more the about star:
https://brainly.com/question/29008154
#SPJ5
A geyser has a rating 2 kVA, 240 V. (a) what is the electrical energy consumed by it in (i) kWh and (ii) joule if it is used for 90 mins. (b) if the cost of electricity is rupees 4.50 per commercial unit find the cost.
See below~
Explanation:
Given, P = 2 kVA = 2 kW,
t = 90 min = 1.5 h
(a) (i) Electrical Energy Consumed = power * time
= 2 kW x 1.5 h
= 3 kWh ( or 3 commercial unit)
(ii) Since 1 kW = 3.6 x 10^6 J
therefore,
Electrical energy consumed = 3 x 3.6 x 10^6 J
= 1.08 x 10^7 J
(b) Cost of electricity
= energy consumed in kWh x cost per kWh
= 3 x Rs 4.50 = Rs. 13.50
Hope it helps you!!Explain what it means when someone says energy can not be created or destroyed.
Answer:
Energy is always reused. Energy cannot be created or destroyed because it always turns into some other type of energy.
Explanation:
A circular loop (10 turns) with a radius of 29 cm is in a magnetic field that
oscillates uniformly between 0.95 T and 0.45 T with a period of 1.00 s.
a. How much time is required for the field to change from 0.95 T to 0.45 T?
b. What is the cross-sectional area of one turn of the loop?
c. Assuming that the loop is perpendicular to the magnetic field, what is the
induced emf in the loop?
Electric Charge
Directions: Identify each of the following as a conductor or an insulator by putting a “c” or an “i” in the blank.
The materials that are conductors are Metal doorknob, Silver, Gold, Copper, Metal coat hanger, Paper clip, while insulators are Carpet, Wood, Rubber, Bulletin board, Clothing, Plastic.
What are electric conductors?
Conductors are materials that allow electric current to pass through them.
What are Insulators?Insulators are materials that do not allow electric current to pass through them.
Examples of conductorsMetal doorknobSilver GoldCopperMetal coat hangerPaper clipExamples of insulatorsCarpet WoodRubberBulletin boardClothingPlasticLearn more about conductors and insulators here: https://brainly.com/question/492289
An incompressible ideal fluid flows steadily through a pipe that has a change in diameter. The fluid speed at a location where the pipe diameter is 8.0 cm is 1.28 m/s. What is the fluid speed at a location where the diameter has narrowed to 5.0 cm
Answer:
A V = A X / t where X / t is speed of fluid
A V = area * velocity (rate of fluid flowing)
A1 V1 = A2 V2 form of equation of continuity
pi (D1 / 2)^2 V1 = pi (D2 / 2)^2 V2
V2 = (D1 / D2)^2 * V1 = (8 / 5)^2 * 1.28 m/s = 3.28 km/s
Sodium-24 has a half-life of 15 hours. after 45 hours, how much sodium-24 will remain of an original 50.0-g sample? 5.56 g 6.25 g 16.7 g 25.0 g
Answer:
6.25 gm
Explanation:
1 /2 * 1/2 * 1/2 = 1/8th of the original
50/8 = 6.25 gm
Answer:
its b
Explanation:
trust
A stone is dropped from the top of a tall building. As it falls in the absence of air resistance, what happens to the de broglie wavelength of the stone?.
Explanation:
lambda = h/mv
hieght is decreasing
velocity is increasing
therfore the wavelength is decreasing.
If a radio wave carries information by changing the amplitude of the transmitted wave, what kind of broadcast might it possibly be?
A) AM radio and analog TV video
B) AM radio only
C) FM radio only
D) FM radio and analog TV sound
if 36 columb of charge pass through a wire in 45 what is it carrying
[tex]\qquad\qquad\huge\underline{{\sf Answer}}[/tex]
Here we go ~
[tex]\qquad \tt \dashrightarrow \:Electric \: \: current = \dfrac{ Charge }{time}[/tex]
[tex]\qquad \tt \dashrightarrow \:E= \dfrac{36 }{45}[/tex]
[tex]\qquad \tt \dashrightarrow \:E= 0.8 \: \: amp[/tex]
At a distance of 10 km from a radio transmitter, the amplitude of the electric field is 0. 20 volts/meter. What is the total power emitted by the radio transmitter?.
a. 10 kW b. 67 kW c. 140 kW d. 245 kW e. 21 kW
The following are secondary sources of energy except a.coal b crude oil c nuclear d wind e wood
Answer:
d) Wind
Explanation:
Secondary energy is energy produced by converting energy available in its natural state in the environment. Hence Wind is a primary source not a secondary source
Español:
¿Me podrian ayudar con esta pregunta? <3
Las aplicaciones de la diferencia potencial en la vida cotidiana.
English:
Could you help me with this question? <3
The applications of the potential difference in everyday life.
Las diferencia de potencial indica el valor de la fuerza o potencial eléctrico entre dos puntos, lo cual permite llevar electricidad a diferentes areas.
¿Qué significa diferencia de potencial?La diferencia de potencial indica la fuerza ejercida por una corriente eléctrica entre dos puntos equidistantes.
La diferencia de potencial se mide en Volts, es decir, en voltaje (V), el cual indica la fuerza de la energía eléctrica que se puede transmitir entre dos puntos.
La diferencia de potencial nos permite tener energía en una vivienda o en una industria, como asi tambien usar un artefacto que requiera de electricidad para funcionar.
Aprende más sobre la diferencia de potencial aquí:
https://brainly.com/question/25094659
(15 points) How many circles do i draw, like in what order
Answer:
U have to draw 3 circles
take a specific point and draw 3 circles of different size from the same point.
A 100kg man wants to burn off 500 kilocalories by running up ar elliptical. How far will he have to climb?
The distance the 100kg man must climb to burn off 500 kilocalories by running up an elliptical path is 2,136.1 m.
Potential energy of the man
The potential energy of the man from a known height can be used to deternine the distance the man would have to climb.
P.E = mgh
Where;
P.E is potential energy, given as 500 kilocalories,
1 kcal = 4186.8 joules
500 kcal = 2,093,400 J
Distance traveled by the manh = P.E/mg
h = (2,093,400) / (100 x 9.8)
h = 2,136.1 m
Learn more about potential energy here: https://brainly.com/question/1242059
A ball on the end of a string is revolving at a uniform rate in a vertical circle of radius 97.7 cm. If its speed is 3.74 m/s, and its mass is 0.182 kg, calculate the tension (in newtons) in the string when the ball is at the bottom of the path.
The tension in the string when the ball is at the bottom of the path is 2.61 Newtons.
TensionA tension is simply referred to as a force along the length of a flexible medium such as strings, cable, ropes etc.
Tension in a string revolving can be determined using the expression;
T = mv² / r
Where m is mass of object, v is velocity and r is radius ( length of string )
Given the data in the question;
Mass of ball m = 0.182kgRadius ( length of string ) r = 97.7cm = 0.977mVelocity = 3.74m/sTension in the string; T = ?To determine tension in the string, we substitute our given values into the expression above.
T = mv² / r
T = (0.182kg × (3.74m/s)²) / 0.977m
T = (0.182kg × 13.9876m²/s²) / 0.977m
T = (2.5457432kgm²/s²) / 0.977m
T = 2.61kgm/s²
T = 2.61N
Therefore, the tension in the string when the ball is at the bottom of the path is 2.61 Newtons.
Learn more about Tension here: https://brainly.com/question/14351325
Blowing up a balloon and letting it go is an example of newton’s.
Answer:
Third Law Of Motion
Explanation:
When we let go of the end, the air rushes out and pushes against the air around the balloon to move it in the opposite direction. Newton describes this effect in his third law.
The blowing up of a balloon and letting it go is an example of newton's third law of motion or action-reaction law.
What is newton's third law?According to Newton's third law, when two bodies come into contact, they exert forces on one another that really are equal in strength and pointed in the opposite direction. The third law is frequently referred to as the law of actions and consequences.
This law applies to bodies in constant or rapid motion and is crucial for understanding problems of static balance, where all forces are in balance. It doesn't only use bookkeeping techniques; the forces it portrays are actual forces. A book laying on a table, for instance, exerts a downwards force equal to its weight on the table. The third law states that the book is subjected to an equal and opposing force from the table.
To know more about newton's third law:
https://brainly.com/question/23772134
#SPJ5
HELP PLS HELP. WILL GIVE BRAINLIEST.
You are trying to roll a toy car up a hill and stop at the top without rolling down the other side of the hill. If the car has a mass of 0.5 kg and the hill is 0.07 meters high, how much kinetic energy should you use on the car to move it to the exact top?
Let's see
According to law of conservation of linear momentum
PE=KEKE=mghKE=0.5(9.8)(0.07)KE=4.9(0.07)KE=0.343JKE=343mJAnswer:
0.35 J
Explanation:
This problem requires the Law of Conservation of Energy.
⇒ Potential energy = Kinetic Energy
⇒ mgh = 1/2mv²
⇒ 0.5 x 10 x 0.07 = KE
⇒ KE = 5 x 0.07
⇒ KE = 0.35 J
How are liquids and gases alike?
Answer:
The particles of both states are free flowing and they fill the container that they are in.
Explanation:
Liquids and gases do not have a set formation like a solid does. Liquids have more range of motion and will fill a container (such as how water will fill a glass). Gas has an even wider range of motion and move around very quickly.
Throughout the reflection, make sure you have a copy of the student guide and your data tables. use the drop-down menus to complete the statements. in part i, the independent variable was . in part ii, the independent variable changed to . the dependent variable for both part i and part ii was .
Mass, Speed and Kinetic Energy.The independent variable changed to . the dependent variable for both part i and part ii was .
What is kinetic energy?We can solve this by analysing the choices and the relations between variables.
It's worth noting that Kinetic Energy is proportional to both speed and mass. Actually, Kinetic Energy is exactly proportional to those factors, meaning that the more mass or speed, the higher the Kinetic Energy.
Having said that, Part I and Part II must have speed and mass as indendepent variable, because Kinetic Energy depends on them.
Then, in the third question, the answer is Kinetic Energy becase that's the dependent variable in both cases Part I and Part II.
Just to remember, the Kinetic Energy is defined as
[tex]KE=\dfrac{1}{2}mv^2[/tex]
Where you can notice the relation between mass, speed and kinetic energy.
Therefore, the right answer are Mass (Part I), Speed (Part II) and Kinetic Energy (Part III).
To know more about Kinetic energy follow
https://brainly.com/question/25959744
Answer
the right answer are Mass (Part I), Speed (Part II) and Kinetic Energy (Part III).
Explanation:
i is trying to explain why the endoplasmic reticulum is important. Which of these analogies for the e
ulum would best help her with this explanation?
The endoplasmic reticulum is like a set of raw materials used to build bricks.
The endoplasmic reticulum is like a truck that transports newly made bricks out of the factory.
The endoplasmic reticulum is like a factory that helps produce, process, and transport bricks.
The endoplasmic reticulum is like a construction worker that builds a structure with bricks.
Answer:
i will say that the endoplasmic reticulum is a complex organelle that plays a pivotal role in protein and lipid synthesis, calcium storage and stress response
Why is the phase of the moon important for a solar eclipse to occur?.