The rms value of current in the inductor is 169.7 A.The frequency of the generator is 15 Hz.The inductive reactance of the inductor is 47.1 Ω.
Given, ΔV=1.20×10^2V sin(30πt), and L=0.500H
We know that V = L di/dt
Here, ΔV = V = 1.20×10^2V sin(30πt)
By integrating both sides, we get∫di = (1/L)∫ΔV dt
Integrating both sides with respect to time, we get:i(t) = (1/L) ∫ΔV dt
The integral of sin(30πt) will be - cos(30πt) / (30π)
Let's substitute the values:∫ΔV dt = ∫1.20×10^2 sin(30πt) dt = -cos(30πt) / (30π)
Therefore, i(t) = (1/L) (-cos(30πt) / (30π))
Now, we can calculate the following parameters:
Peak value of current, I0= (1/L) × Vmax= (1/0.5) × 120= 240 A
So, the peak value of current is 240 A.
The rms value of current is given by Irms= I0/√2= 240/√2= 169.7 A
Therefore, the rms value of current in the inductor is 169.7 A.
The given voltage equation is ΔV=1.20×10^2 V sin(30πt)
The voltage equation is given by Vmax sinωt
Here, Vmax = 1.20×10^2V and ω = 30π
The frequency of the generator is given by f = ω / (2π) = 15 Hz
Therefore, the frequency of the generator is 15 Hz.
The inductive reactance of an inductor is given by XL= 2πfL= 2 × 3.14 × 15 × 0.5= 47.1 Ω
Therefore, the inductive reactance of the inductor is 47.1 Ω.
Know more about frequency here,
https://brainly.com/question/29739263
#SPJ11
prove capacitance ( c=q/v) in gows low
The equation [tex]C =\frac{Q}{V}[/tex] can be derived from Gauss's law when applied to a parallel plate capacitor. This equation represents the relationship between capacitance, charge, and voltage in a capacitor.
Gauss's law states that the electric flux through a closed surface is proportional to the charge enclosed by that surface. When applied to a parallel plate capacitor, we consider a Gaussian surface between the plates.
Inside the capacitor, the electric field is uniform and directed from the positive plate to the negative plate. By applying Gauss's law, we find that the electric flux passing through the Gaussian surface is equal to the charge enclosed divided by the permittivity of free space (ε₀).
The electric field between the plates can be expressed as [tex]E =\frac{V}{d}[/tex], where V is the voltage across the plates and d is the distance between them. By substituting this expression into Gauss's law and rearranging, we obtain [tex]Q =\frac{C}{V}[/tex], where Q is the charge on the plates and C is the capacitance.
Dividing both sides of the equation by V, we get [tex]C =\frac{Q}{V}[/tex], which is the expression for capacitance. This equation shows that capacitance is the ratio of the charge stored on the capacitor to the voltage across it.
Learn more about capacitor here:
https://brainly.com/question/31627158
#SPJ11
Two point changes 25 cm agat have an electnc Part A potential enerpy +150 is The toeal charge is 20 nC What ike the two charges? Express your answers using two significant figures. Enteryour answers numeticaliy separated by commas.
Given: Potential Energy, U = +150 V, separation distance, r = 25 cm = 0.25 m, and Total charge, Q = 20 nC.To find: Find the two charges, q1 and q2.
Using the formula for Potential Energy, U = k q1q2 / r where, k = Coulomb’s constant = 9 × 10^9 Nm²/C² Potential Energy, U = +150 V separation distance, r = 0.25 m.
Therefore, we get:150 = (9 × 10^9) q1q2 / 0.25q1q2 = (150 × 0.25) / (9 × 10^9)q1q2 = 4.17 × 10^-6 C²Total charge, Q = 20 nCq1 + q2 = Qq1 = Q - q2q1 = 20 × 10^-9 C - 4.17 × 10^-6 Cq1 = -4.168 × 10^-6 C (Approximately equals to -4.2 × 10^-6 C)q2 = 4.17 × 10^-6 C (Approximately equals to 4.2 × 10^-6 C)Therefore, the charges are approximately equals to -4.2 × 10^-6 C and 4.2 × 10^-6 C.
Learn more on Potential energy here:
brainly.in/question/26640823
#SPJ11
The electrical resistivity of a sample of copper at 300 K is 1.0 micro Ohm.cm. Find the relaxation time of free electrons in copper, given that each copper atom contributes one free electron. The density of copper is 8.96 gm/cm³.
The electrical resistivity of a sample of copper at 300 K is 1.0 micro Ohm.cm. The density of copper is 8.96 gm/cm³. Each copper atom contributes one free electron. The relaxation time of free electrons in copper is 3.57× 10⁻¹⁴ seconds.
Electrical resistivity (ρ) of the material is given by;$$\rho = \frac{m}{ne^2\tau}$$ Where, m = Mass of the electron = Number of electrons per unit volume (or density of free electron) e = Charge on an electron$$\tau = \text{relaxation time of the free electrons}$$Rearranging the above formula, we get;$$\tau = \frac{m}{ne^2\rho}$$We know that, density of copper (ρ) = 8.96 gm/cm³ = 8960 kg/m³Resistivity of copper (ρ) = 1.0 × 10⁻⁶ ohm cm, Charge on an electron (e) = 1.6 × 10⁻¹⁹ C Number of free electrons per unit volume of copper, n = The number of free electrons contributed by each copper atom = 1. Mass of an electron (m) = 9.1 × 10⁻³¹ kg. Putting the above values in the equation of relaxation time of free electrons in copper, we get;$$\tau = \frac{9.1 × 10^{-31}}{(1)(1.6 × 10^{-19})^2(1.0 × 10^{-6})}$$$$\tau = 3.57 × 10^{-14}\ seconds$$. Therefore, the relaxation time of free electrons in copper is 3.57 × 10⁻¹⁴ seconds.
Learn more about electrical resistivity:
https://brainly.com/question/13735984
#SPJ11
An object is thrown vertically downward at 12 m/s from a window and hits the ground 1.2 s later. What is the height of the window above the ground? (Air resistance is negligible.) A. 14.6 m B. 28.2 m C. 3.5 m D. 7.3 m E. 21 m
The height of the window above the ground is A) 14.6 m.
To determine the height of the window above the ground, we can utilize the kinematic equation for vertical motion. The equation is given by:
h = v_i * t + (1/2) * g * t^2
In this equation, h represents the height of the window above the ground, v_i is the initial velocity (-12 m/s in this case), t is the time taken (1.2 s), and the value of g corresponds to the acceleration caused by gravity and is approximately 9.8 m/s².
Substituting the given values into the equation, we can calculate the height:
h = -12 * 1.2 + (1/2) * 9.8 * (1.2)^2
= -14.56 m
Since we are interested in the height above the ground, we take the absolute value of the height: |h| = 14.56 m.
Therefore, the correct option is A) 14.6 m, indicating that the height of the window above the ground is approximately 14.6 meters.
Learn more about acceleration at: https://brainly.com/question/460763
#SPJ11
An FM radio station broadcasts at a frequency of 100 MHz. The period of this wave is closest to 10 ns 1 ns 10 us 100 ns
The period of the FM radio wave with a frequency of 100 MHz is closest to 10 ns.
The period of a wave is the time it takes for one complete cycle to occur. It is the reciprocal of the frequency. In this case, the FM radio station broadcasts at a frequency of 100 MHz, which means it undergoes 100 million cycles per second. To calculate the period, we divide 1 second by the frequency. In this case, the period is approximately 1/100 million seconds, which is equal to 10 ns (nanoseconds).
A nanosecond is one billionth of a second, and it represents a very short period of time. This short period is necessary for the FM radio wave to oscillate at such a high frequency. The wave completes one cycle every 10 ns, meaning it repeats its pattern 100 million times in one second. This rapid oscillation allows the transmission and reception of audio signals with high fidelity. Therefore, the period of the FM radio wave with a frequency of 100 MHz is closest to 10 ns.
Learn more about period of a FM radio wave:
https://brainly.com/question/28480049
#SPJ11
A long straight wire carrying a 4 A current is placed along the x-axis as shown in the figure. What is the magnitude of the magnetic field at a point P, located at y = 9 cm, due to the current in this wire?
To find the magnitude of the magnetic field at point P due to the current in the wire, we can use the formula for the magnetic field produced by a long straight wire. The magnitude of the magnetic field at point P depends on the distance from the wire and the current flowing through it.
The magnetic field produced by a long straight wire at a point P located a distance y away from the wire can be calculated using the formula B = (μ₀ * I) / (2π * y), where B is the magnetic field, μ₀ is the permeability of free space (a constant), I is the current in the wire, and y is the distance from the wire.
In this case, the current in the wire is given as 4 A and the point P is located at y = 9 cm. We can substitute these values into the formula to calculate the magnitude of the magnetic field at point P.
Remember to convert the distance from centimeters to meters before substituting it into the formula.
Learn more about the magnetic field here:
https://brainly.com/question/14848188
#SPJ11
magnetic force on the wire? \( \begin{array}{lll}x \text {-component } & \text { « } \mathrm{N} \\ y \text {-component } & \text { ソ } & \mathrm{N} \\ z \text {-component } & \text { N }\end{array}
The magnetic force is a vector quantity that is perpendicular to both the current direction and the magnetic field.
Magnetic force on the wireThe magnetic force acting on a wire is directly proportional to the current, length of the wire, and magnetic field. When a current-carrying conductor is positioned inside a magnetic field, it experiences a force perpendicular to both the current and magnetic field lines.The magnetic force, like the electric force, is a field force that doesn't need contact between two objects.
Magnetic forces, on the other hand, are always present between magnetic objects. The force on a wire in a magnetic field is determined by Fleming's left-hand rule.The force on a wire carrying current I and length l in a magnetic field B can be calculated using the formula F = BIlsinθ. Here, θ is the angle between the magnetic field and the current direction. Let the current-carrying wire be placed in a uniform magnetic field B. We'll see the force that acts on it.
The magnetic force exerted on the wire is F = IlBsinθ, where l is the length of the wire in the magnetic field and θ is the angle between the current and the magnetic field. If the wire is parallel to the magnetic field, θ = 0 and the magnetic force F is zero. If the wire is perpendicular to the magnetic field, θ = 90°, and the magnetic force is maximum. The magnetic force is a vector quantity that is perpendicular to both the current direction and the magnetic field.
Learn more about magnetic field here,
https://brainly.com/question/14411049
#SPJ11
In complex electric power system, please give the basic description about the control of voltage and reactive power. 6) The typical short circuits faults happened in power system, please give the typical types.
In complex electric power systems, the voltage and reactive power are controlled using various devices and techniques.
The control of voltage and reactive power is necessary to maintain the system's stability and ensure reliable power supply to the loads. In general, there are two ways to control the voltage and reactive power of a power system: through the use of automatic voltage regulators (AVRs) and reactive power compensation devices.
AVRs are used to regulate the voltage at the load buses and maintain the voltage within an acceptable range. These devices work by automatically adjusting the excitation level of the generator to compensate for changes in load demand or system conditions. Reactive power compensation devices, such as capacitors and reactors, are used to control the flow of reactive power in the system. These devices are used to reduce voltage drops, improve power factor, and increase the system's stability.
In a power system, short circuits can occur due to various reasons such as equipment failure, lightning strikes, and human error. The typical types of short circuit faults that occur in power systems are:
1. Three-phase faults: These occur when all three phases of the system short circuit to each other or to ground. This type of fault is the most severe and can cause extensive damage to equipment and the system.
2. Single-phase faults: These occur when a single phase of the system short circuits to another phase or to ground. This type of fault is less severe than three-phase faults but can still cause significant damage.
3. Double-phase faults: These occur when two phases of the system short circuit to each other. This type of fault is less common but can still cause damage to equipment and the system.
In conclusion, the control of voltage and reactive power is essential in complex electric power systems. The use of AVRs and reactive power compensation devices helps maintain system stability and reliable power supply. Short circuits faults in power systems can occur due to various reasons, and the most typical types are three-phase faults, single-phase faults, and double-phase faults.
Learn more about short circuit faults here:
https://brainly.com/question/4525793
#SPJ11
Are these LED Planck's constant calculations correct? (V = LED threshold voltage)
Do the results agree with the theoretical value of h = 6.63 x 10–34 J s, given each calculated h has an uncertainty value of ± 0.003 x10-34 J s?
Plancks constant: h =
eV2
;
where: Ared = 660 nm, Ayellow = 590 nm, Agreen = 525 nm, Ablue 470 nm.
C
Red LED: h= (1.602 x10-
To determine if the LED Planck's constant calculations are correct, let's examine given formula and calculate the value for the red LED: h = eV / c
First, we need to find the energy of the red LED photon using the equation: E_red = hc / λ_red
E_red = (6.63 x 10^-34 J s * 3 x 10^8 m/s) / (660 x 10^-9 m)
= 2.83 x 10^-19 J
Now, we can calculate threshold voltage V for the red LED: V = E_red / e
Where: e = 1.602 x 10^-19 C (elementary charge)
V = (2.83 x 10^-19 J) / (1.602 x 10^-19 C)
≈ 1.77 V
The calculated value for the red LED threshold voltage is approximately 1.77 V.
To compare with the theoretical value of Planck's constant, we need to calculate the value of h using the formula:
h = eV / λ_red
h = (1.602 x 10^-19 C * 1.77 V) / (660 x 10^-9 m)
≈ 4.33 x 10^-34 J s
Comparing this calculated value with the theoretical value of h = 6.63 x 10^-34 J s, that they do not agree.
Learn more about LED here:
https://brainly.com/question/8481754
#SPJ11
Can I use both multiplexer and demultiplexer in one circuit? Explain. Please provide a diagram.
Yes, it is possible to use both a multiplexer and a demultiplexer in one circuit. A multiplexer (MUX) is a digital circuit that combines multiple input signals into a single output, based on the control inputs.
On the other hand, a demultiplexer (DEMUX) does the opposite, taking a single input and routing it to one of several outputs, again based on the control inputs.
By combining a MUX and a DEMUX, we can create a circuit that performs bidirectional data transmission or routing. The MUX can be used to select the input signal, while the DEMUX can be used to select the output for that signal. This can be useful in scenarios where data needs to be transmitted or routed in both directions, such as in communication systems, data buses, or multiprocessor systems. By using both a MUX and a DEMUX together, we can effectively manage and control the flow of data in a more flexible manner within a circuit.
To know more about multiplexer, here
brainly.com/question/15052768
#SPJ4
Two particles are fixed to an x axis: particle 1 of charge q₁ = 3.00 × 10⁻⁸ C at x = 22.0 cm and particle 2 of charge q₂ = −5.29q₁ at x = 69.0 cm. At what coordinate on the x axis is the electric field produced by the particles equal to zero?
The coordinate on the x-axis where the electric field is zero is 44.4 cm.
Particle 1 of charge q₁ = 3.00 × 10⁻⁸ C at x = 22.0 cm
Particle 2 of charge q₂ = −5.29q₁ at x = 69.0 cm.
The formula to calculate electric field due to a point charge is given by:
E = kq/r²
Here,
E is the electric field,
q is the charge on the particle,
r is the distance between the two points
k is the Coulomb constant k = 9 × 10^9 N·m²/C².
For two point charges, the electric field is given by:
E = kq₁/r₁² + kq₂/r₂²,
where r₁ and r₂ are the distances from the point P to each charge q₁ and q₂ respectively.
Using this formula,
The electric field due to particle 1 at point P is given by:
E₁ = kq₁/r₁²
The electric field due to particle 2 at point P is given by:
E₂ = kq₂/r₂²
Now we have, E₁ = -E₂, for the net electric field to be zero.
So,
kq₁/r₁² = kq₂/r₂²
q₂/q₁ = 5.29
The distance of the point P from the charge q₁ is (69 - x) cm.
The distance of the point P from the charge q₂ is (x - 22) cm.
Then, applying the formula, we have:
kq₁/(69 - x)² = kq₂/(x - 22)²
q₂/q₁ = 5.29
kq₁/(69 - x)² = k(-5.29q₁)/(x - 22)²
1/(69 - x)² = -5.29/(x - 22)²
(69 - x)² = 5.29(x - 22)²
Solving this equation, we get:
x = 44.4 cm (approx)
Therefore, the coordinate on the x-axis where the electric field is zero is 44.4 cm.
Learn more about the electric field:
brainly.com/question/19878202
#SPJ11
An aircraft engine starts from rest; and 6 seconds later, it is rotating with an angular speed of 138 rev/min. If the angular acceleration is constant, how many revolutions does the propeller undergo during this time? Give your answer to 2 decimal places
During this time, the propeller undergoes approximately 6.95 revolutions.
Initial angular velocity, ω1 = 0
Final angular velocity, ω2 = 138 rev/min
Time taken, t = 6 seconds
To find the number of revolutions the propeller undergoes, we need to calculate the angular displacement.
We can use the equation:
θ = ω1*t + (1/2)αt²
Since the initial angular velocity is 0, the equation simplifies to:
θ = (1/2)αt²
We know that the final angular velocity in rev/min can be converted to rad/s by multiplying it by (2π/60), and the final angular velocity in rad/s is given by:
ω2 = 138 rev/min * (2π/60) rad/s = 14.44 rad/s
By substituting the provided data into the equation, we can determine the result:
θ = (1/2)α(6)²
To find α, we can use the equation:
α = (ω2 - ω1) / t
By substituting the provided data into the equation, we can determine the result:
α = (14.44 - 0) / 6 = 2.407 rad/s²
Now we can calculate the angular displacement:
θ = (1/2)(2.407)(6)² = 43.63 radians
To calculate the number of revolutions, we divide the angular displacement by 2π:
n = θ / (2π) = 43.63 / (2π) ≈ 6.95 revolutions
Therefore, during this time, the propeller undergoes approximately 6.95 revolutions.
Learn more about revolutions at: https://brainly.com/question/16533738
#SPJ11
Given a three-phase AC power network with a load, which consumes 100 MW with a power factor of 0.8 (lagging). Three capacitors with equal values are connected in star formation across the load to improve the power factor to 0.96 (leading). Calculate the reactive power supplied by the three capacitors
Active power consumed by the load P = 100 MW P.F of the load cos φ = 0.8 (lagging)
P.F of the load after connecting capacitors cos φ2 = 0.96 (leading)
The formula to calculate the reactive power is
Q = P(tan φ1 - tan φ2) Where, Q = Reactive power required by capacitors P = Active power consumed by the load
cos φ1 = Power factor of the load before adding capacitors
cos φ2 = Power factor of the load after adding capacitors
tan φ1 = √(1 - cos²φ1)/cos φ1
tan φ1 = √(1 - 0.8²)/0.8 = 0.6
tan φ2 = √(1 - cos²φ2)/cos φ2
tan φ2 = √(1 - 0.96²)/0.96 = 0.4
Therefore, Q = 100 × (0.6 - 0.4) = 20 MW
Thus, the reactive power supplied by the three capacitors is 20 MW.
Read up more about capacitors: https://brainly.com/question/21851402
#SPJ11
A beam of light in air is incident on the surface of a rectangular block of clear plastic (n = 1.49). If the velocity of the beam before it enters the plastic is 3.00E+8 m/s, what is its velocity inside the block? a. 3.00E+8 m/s b. 1.35E+8 m/s
c. 2.01E+8 m/s d. 2.46E+8 m/s
A beam of light in air is incident on the surface of a rectangular block of clear plastic (n = 1.49). If the velocity of the beam before it enters the plastic is 3.00E+8 m/s the velocity inside the block can be calculated as follows:
`n = c/v` where c is the velocity of light in a vacuum and v is the velocity of light in the medium. The velocity of light in the medium is calculated using `v = c/n`.
Therefore, `v = 3.00E+8 m/s / 1.49 = 2.01E+8 m/s`.
Hence, the velocity of the beam inside the block is 2.01E+8 m/s, and the answer is option (c) 2.01E+8 m/s.
Learn more about light incident on various media: https://brainly.com/question/15838784
#SPJ11
An unstable high-energy particle enters a detector and leaves a track 0.855 mm long before it decays. Its speed relative to the detector was 0.927c. What is its proper lifetime in seconds? That is, how long would the particle have lasted before decay had it been at rest with respect to the detector? Number ___________ Units _______________
The proper lifetime of the particle have lasted before decay had it been at rest with respect to the detector is 3.101 × 10⁻¹⁶ s. That is, Number 3.101 × 10⁻¹⁶ Units seconds.
It is given that, Length of track, l = 0.855 mm, Speed of the particle relative to the detector, v = 0.927c.
Let's calculate the proper lifetime of the particle using the length of track and speed of the particle.To calculate the proper lifetime of the particle, we use the formula,
[tex]\[\tau =\frac{l}{v}\][/tex] Where,τ = Proper lifetime of the particle, l = Length of the track and v = Speed of the particle relative to the detector
Substituting the values, we get:
τ = l / v = 0.855 mm / 0.927 c
To solve this equation, we need to use some of the conversion factors:
1 c = 3 × 10⁸ m/s
1 mm = 10⁻³ m
So, substituting the above values in the above equation, we get,
τ = (0.855 × 10⁻³ m) / (0.927 × 3 × 10⁸ m/s)
τ = 3.101 × 10⁻¹⁶ s
Hence, the proper lifetime of the particle is 3.101 × 10⁻¹⁶ s (seconds).
To learn more about speed: https://brainly.com/question/13943409
#SPJ11
The current in an 80-mH inductor increases from 0 to 60 mA. The energy stored in the (d) 4.8 m] inductor is: (a) 2.4 m) (b) 0.28 m) (c) 0.14 m/
The current in an 80-mH inductor, when it increases from 0 to 60 mA, the energy gets stored in the inductor. The energy that is stored in the inductor is 0.14 mJ.
The energy stored in an inductor can be calculated using the formula:
[tex]E = (\frac{1}{2}) * L * I^2[/tex]
where E is the energy stored, L is the inductance, and I is the current. Given an inductance of 80 mH (0.08 H) and a current increase from 0 to 60 mA (0.06 A), we can substitute these values into the formula:
[tex]E = (\frac{1}{2}) * 0.08 * (0.06)^2[/tex]
= 0.000144 J
Since the energy is usually expressed in millijoules (mJ), we convert the answer:
0.000144 J * 1000 mJ/J = 0.144 mJ
Therefore, the energy stored in the 80-mH inductor when the current increases from 0 to 60 mA is 0.144 mJ or approximately 0.14 mJ.
Learn more about inductance here:
https://brainly.com/question/31127300
#SPJ11
For crystal diffraction experiments, wavelengths on the order of 0.20 nm are often appropriate, since this is the approximate spacing between atoms in a solid. Find the energy in eV for a particle with this wavelength if the particle is (a) a photon, (b) an electron, (c) an alpha particle (mc² = 3727 MeV).
a. The energy of a photon is 62.1 eV.
b. The energy of an electron is 227.8 eV.
c. The energy of an alpha particle is 2.33 x 10²⁷ eV
a. Energy of a photon:
E = hc/λ
where,
h = Planck's constant = 6.626 x 10⁻³⁴ J-s
c = speed of light = 3 x 10⁸ m/s
λ = wavelength of photon
E = (6.626 x 10⁻³⁴ J-s) x (3 x 10⁸ m/s) / (0.20 x 10⁻⁹ m)
= 9.939 x 10⁻¹² J
Convert J to eV by dividing by 1.6 x 10⁻¹⁹ J/eV,
E = (9.939 x 10⁻¹² J) / (1.6 x 10⁻¹⁹ J/eV)
≈ 62.1 eV
Therefore, the energy of a photon with this wavelength is 62.1 eV.
b. Energy of an electron:
E = p²/2m
where,
p = momentum of electron
m = mass of electron = 9.1 x 10⁻³¹ kg
λ = h/p
p = h/λ
E = h²/2m
λ²= (6.626 x 10⁻³⁴ J-s)² / [2 x (9.1 x 10⁻³¹ kg) x (0.20 x 10⁻⁹ m)²]
= 3.648 x 10⁻¹⁰ J
Convert J to eV by dividing by 1.6 x 10⁻¹⁹ J/eV,
E = (3.648 x 10⁻¹⁰ J) / (1.6 x 10⁻¹⁹ J/eV)
≈ 227.8 eV
Therefore, the energy of an electron with this wavelength is 227.8 eV.
c. Energy of an alpha particle:
E = mc² / √(1 - v²/c²)
where,
m = mass of alpha particle
c = speed of light = 3 x 10⁸ m/s
λ = h/p
p = h/λ
v = p/m
= (h/λ)/(mc)
= h/(λmc)
E = mc² / √(1 - v²/c²)
E = (3727 MeV) x (1.6 x 10⁻¹³ J/MeV) / √(1 - (6.626 x 10⁻³⁴ J-s/(0.20 x 10⁻⁹ m x 3727 x 1.67 x 10⁻²⁷ kg x (3 x 10⁸ m/s))²))
≈ 3.72 x 10¹³ J
Convert J to eV by dividing by 1.6 x 10⁻¹⁹ J/eV,
E = (3.72 x 10¹³ J) / (1.6 x 10⁻¹⁹ J/eV)
≈ 2.33 x 10²⁷ eV
Therefore, the energy of an alpha particle with this wavelength is 2.33 x 10²⁷ eV.
Learn more about the alpha particle:
brainly.com/question/22799756
#SPJ11
A perfect fixed mass of gas slowly follows the evolutions in the Figure below.1) Which of these developments is at constant temperature (isothermal)?
2) What evolution is at constant volume (isochore)
The development at constant temperature (isothermal) is B-C, and the development at constant volume (isochore) is D-E.
The development at constant temperature (isothermal) is B-C. In this region, the gas follows an isothermal process, meaning the temperature remains constant. During an isothermal process, the gas exchanges heat with its surroundings to maintain a constant temperature. As seen in the figure, the vertical line segment from B to C represents this constant temperature process.
The evolution at constant volume (isochore) is D-E. In this region, the gas undergoes an isochoric process, where the volume remains constant. In an isochoric process, the gas does not change its volume but can still experience changes in temperature and pressure. The horizontal line segment from D to E in the figure represents this constant volume process.
Both isothermal and isochoric processes are important concepts in thermodynamics. Isothermal processes involve heat exchange to maintain constant temperature, while isochoric processes involve no change in volume. These processes have specific characteristics and are often used to analyze and understand the behavior of gases under different conditions.
Learn more about isothermal and isochore processes:
https://brainly.com/question/13281279
#SPJ11
Two parallel straight wires are 9 cm apart and 53 m long. Each one carries a 20 A current in the same direction. One wire is securely anchored, and the other is attached in the center to a movable cart. If the force needed to move the wire when it is not attached to the cart is negligible, with what magnitude force does the wire pull on the cart? Express your answer in mN without decimal place. Only the numerical value will be graded. (uo = 4 x 10-7 T.m/A) mN At a point 12 m away from a long straight thin wire, the magnetic field due to the wire is 0.1 mT. What current flows through the wire? Express your answer in kA with one decimal place. Only the numerical value will be graded. (uo = 4πt x 10-7 T.m/A) ΚΑ How much current must pass through a 400 turn ideal solenoid that is 3 cm long to generate a 1.0 T magnetic field at the center? Express your answer in A without decimal place. Only the numerical value will be graded. (uo = 4 x 10- 7 T.m/A) A A proton having a speed of 4 x 106 m/s in a direction perpendicular to a uniform magnetic field moves in a circle of radius 0.4 m within the field. What is the magnitude of the magnetic field? Express your answer in T with two decimal places. Only the numerical value will be graded. (e = 1.60 × 10-1⁹ C, mproton = 1.67 x 10-27 kg
Q1. Two parallel straight wires are 9 cm apart and 53 m long. Each one carries a 20 A current in the same direction. One wire is securely anchored, and the other is attached in the center to a movable cart. If the force needed to move the wire when it is not attached to the cart is negligible, with what magnitude force does the wire pull on the cart? Express your answer in mN without decimal place. Only the numerical value will be graded. (uo = 4 x 10-7 T.m/A)The magnetic force between the wires is given by F = μo * I1 * I2 * L / (2 * π * d) where F is the force between the wires, μo is the magnetic constant, I1 and I2 are the current in the two wires, L is the length of the wires, and d is the distance between them. Since the two wires have the same current and are in the same direction, we can simplify the equation to:F = μo * I^2 * L / (2 * π * d)We can now substitute the values to get:F = (4 * π * 10^-7) * (20)^2 * 53 / (2 * π * 0.09)F = 24.9 mNThe force with which the wire pulls on the cart is 24.9 mN.Q2. At a point 12 m away from a long straight thin wire, the magnetic field due to the wire is 0.1 mT. What current flows through the wire? Express your answer in kA with one decimal place. Only the numerical value will be graded. (uo = 4πt x 10-7 T.m/A)We know that the magnetic field due to a long straight wire is given by B = μo * I / (2 * π * r), where B is the magnetic field, μo is the magnetic constant, I is the current in the wire, and r is the distance from the wire. Substituting the given values, we get:0.1 * 10^-3 = (4 * π * 10^-7) * I / (2 * π * 12)I = 0.1 * 10^-3 * 2 * π * 12 / (4 * π * 10^-7)I = 1.5 kAThe current flowing through the wire is 1.5 kA.Q3. How much current must pass through a 400 turn ideal solenoid that is 3 cm long to generate a 1.0 T magnetic field at the center? Express your answer in A without decimal place. Only the numerical value will be graded. (uo = 4 x 10- 7 T.m/A)The magnetic field inside an ideal solenoid is given by B = μo * n * I, where B is the magnetic field, μo is the magnetic constant, n is the number of turns per unit length, and I is the current in the solenoid. Since the solenoid is ideal, we can assume that the magnetic field is uniform throughout and the length is much greater than the radius. Therefore, we can use the formula for the magnetic field at the center of the solenoid, which is:B = μo * n * ISubstituting the given values, we get:1.0 = (4 * π * 10^-7) * 400 / (3 * 10^-2) * II = 7.45 AThe current that must pass through the solenoid to generate a 1.0 T magnetic field at the center is 7.45 A.Q4. A proton having a speed of 4 x 106 m/s in a direction perpendicular to a uniform magnetic field moves in a circle of radius 0.4 m within the field. What is the magnitude of the magnetic field? Express your answer in T with two decimal places. Only the numerical value will be graded. (e = 1.60 × 10-1⁹ C, mproton = 1.67 x 10-27 kg)The magnetic force acting on a charged particle moving in a magnetic field is given by F = q * v * B, where F is the magnetic force, q is the charge of the particle, v is its velocity, and B is the magnetic field. This force is directed perpendicular to both the velocity and the magnetic field, which causes the particle to move in a circular path with radius r given by:r = mv / (qB)where m is the mass of the particle. We can rearrange this equation to solve for the magnetic field:B = mv / (qr)Substituting the given values, we get:B = (1.67 * 10^-27) * (4 * 10^6) / ((1.6 * 10^-19) * 0.4)B = 0.0525 TThe magnitude of the magnetic field is 0.05 T (to two decimal places).
Express your answer in nanocoulombs and to three significant figures. Question 1 What are the sign and magnitude of a point charge that produces an electric potential of 209 V at a distance of 5.88 mm ? Express your answer in nanocoulombs.
The magnitude of the charge is 13.6 nC and since the electric potential is positive, the charge on the point charge is also positive.
The electric potential formula is given as: V = kQ/d, where V is the electric potential, k is Coulomb's constant, Q is the charge, and d is the distance between the charges. We can solve for the magnitude of the charge using this formula.The magnitude of the charge can be found as follows:Q = Vd/kWhere V is 209 V, d is 5.88 mm (which is 5.88 × 10⁻³ m), and k is Coulomb's constant which is 8.99 × 10⁹ Nm²/C².
So, substituting the values in the formula:Q = Vd/k= (209 V) × (5.88 × 10⁻³ m) / (8.99 × 10⁹ Nm²/C²)= 1.36 × 10⁻⁸ C or 13.6 nC (to three significant figures).Therefore, the magnitude of the charge is 13.6 nC and since the electric potential is positive, the charge on the point charge is also positive.
Learn more about magnitude here,
https://brainly.com/question/30337362
#SPJ11
Compare and contrast the following types of radiation, discussing their physical properties and shielding techniques: a) alpha and gamma radiation b) beta and beta radiation
Alpha and beta radiation have different physical properties and shielding techniques than gamma radiation. It is important to understand the differences between these types of radiation in order to protect ourselves and others from their harmful effects.
When comparing and contrasting alpha and gamma radiation, their physical properties and shielding techniques are two important aspects to consider. Alpha radiation consists of a helium nucleus with two protons and two neutrons, which means that it has a positive charge and a high ionizing ability. It is also relatively heavy and slow-moving, and can be stopped by a few sheets of paper or human skin.
On the other hand, gamma radiation is a high-energy photon that has no charge or mass, and it is able to penetrate most materials with ease. Gamma radiation can be shielded with materials that are dense and thick, such as lead or concrete.When comparing and contrasting beta and beta radiation, their physical properties and shielding techniques are also important.
Beta radiation consists of high-energy electrons that have a negative charge and a moderate ionizing ability. It is relatively light and fast-moving, and can penetrate materials such as aluminum and plastic. Beta radiation can be shielded with materials that are denser than air, such as aluminum or plastic.
Gamma radiation, like alpha radiation, is a high-energy photon that can penetrate most materials with ease. Gamma radiation can be shielded with materials that are dense and thick, such as lead or concrete.
In conclusion, alpha and beta radiation have different physical properties and shielding techniques than gamma radiation. It is important to understand the differences between these types of radiation in order to protect ourselves and others from their harmful effects.
Know more about radiation here,
https://brainly.com/question/31106159
#SPJ11
An atom of $Be iss at rest, minding its own business, when suddenly it decays into He + He, that is two alpha particles. Find the kinetic energy of each of these He has an atomic mass of 4.002603 u, and Be has an atomic mass of 8.005305 u. Report your answer in keV, rounded to zero decimal places
Answer:
The kinetic energy of He has an atomic mass of 4.002603 u, and Be has an atomic mass of 8.005305 u is 1.329288keV
Mass of helium atom (He) = 4.002603 u
Mass of beryllium atom (Be) = 8.005305 u
Since the beryllium atom is initially at rest, the total momentum before the decay is zero. Therefore, the total momentum after the decay must also be zero to satisfy the conservation of momentum.
Let's denote the kinetic energy of each helium atom as KE_He1 and KE_He2.
After the decay, the two helium atoms move in opposite directions with equal and opposite momenta. This means their momenta cancel out, resulting in a total momentum of zero.
The momentum of an object is given by the equation:
p = mv
Since the total momentum is zero, the sum of the momenta of the two helium atoms must also be zero:
p_He1 + p_He2 = 0
Using the momentum equation, we have:
(m_He1 * v_He1) + (m_He2 * v_He2) = 0
Since the masses of the helium atoms are the same (m_He1 = m_He2), we can rewrite the equation as:
m_He * (v_He1 + v_He2) = 0
Since the masses are positive, the velocities must be equal in magnitude but opposite in direction:
v_He1 = -v_He2
Now, let's calculate the kinetic energy of each helium atom:
KE_He1 = (1/2) * m_He * (v_He1)^2
KE_He2 = (1/2) * m_He * (v_He2)^2
Since the velocities are equal in magnitude but opposite in direction, their squares are equal:
(v_He1)^2 = (v_He2)^2 = v^2
Therefore, the kinetic energy of each helium atom can be written as:
KE_He1 = KE_He2 = (1/2) * m_He * v^2
Now, let's substitute the values:
m_He = 4.002603 u
v is the velocity of each helium atom after the decay, which we need to determine.
To convert the mass from atomic mass units (u) to kilograms (kg), we use the conversion factor:
1 u = 1.66053906660 x 10^(-27) kg
m_He = 4.002603 u * (1.66053906660 x 10^(-27) kg/u)
= 6.6446573353 x 10^(-27) kg
To find the velocity of the helium atoms, we need to consider the conservation of energy. The total energy before the decay is the rest energy of the beryllium atom, which is given by:
E_total = m_Be * c^2
The total energy after the decay is the sum of the kinetic energies of the helium atoms:
E_total = 2 * KE_He
Setting these two expressions for total energy equal to each other, we have:
m_Be * c^2 = 2 * (1/2) * m_He * v^2
Simplifying the equation:
v^2 = (m_Be * c^2) / (2 * m_He)
Now, we substitute the values:
m_Be = 8.005305 u * (1.66053906660 x 10^(-27) kg/u) = 1.329288
Therefore, The kinetic energy of He has an atomic mass of 4.002603 u, and Be has an atomic mass of 8.005305 u is 1.329288keV
Learn more about kinetic energy, here
https://brainly.com/question/30337295
#SPJ11
A monatomic ideal gas starts at a volume of 3L, and 75 kPa. It is compressed isothermally until its pressure is 200 kPa. Determine the amount of work done, the amount of heat that flows, and the change in internal energy of the gas. Also indicate the direction (into or out of the gas) for the work and the heat.
during the isothermal compression of the monatomic ideal gas from 3L and 75 kPa to 200 kPa, the gas does not undergo any change in internal energy. The work done on the gas is -213 J, indicating compression, and the same amount of heat flows into the gas.
In an isothermal process, the temperature of the gas remains constant. The work done by an ideal gas during an isothermal process can be calculated using the formula:Work = nRT ln(V2/V1),where n is the number of moles of the gas, R is the ideal gas constant, T is the temperature, and V1 and V2 are the initial and final volumes, respectively.
Since the gas is monatomic, its internal energy is solely dependent on its temperature, given by the equation:Internal energy = (3/2) nRT,where (3/2) nRT represents the average kinetic energy of the gas particles.Since the process is isothermal, the change in internal energy is zero. Therefore, the heat flow into the gas is equal to the amount of work done, which is -213 J.
The negative sign indicates that work is done on the gas. Therefore ,during the isothermal compression of the monatomic ideal gas from 3L and 75 kPa to 200 kPa, the gas does not undergo any change in internal energy. The work done on the gas is -213 J, indicating compression, and the same amount of heat flows into the gas.
Learn more about isothermal here:
https://brainly.com/question/32558407
#SPJ11
Photoelectric effect is observed on two metal surfaces.
Light of wavelength 300.0 nm is incident on a metal that has a work function of 2.80 eV. What is the maximum speed of the emitted electrons?
...m/s
Therefore, the maximum speed of the emitted electrons is 1.62 x 10⁶ m/s.
The photoelectric effect is observed on two metal surfaces. If light of wavelength 300.0 nm is incident on a metal that has a work function of 2.80 eV, the maximum speed of the emitted electrons is 1.62 x 10⁶ m/s. What is the photoelectric effect? The photoelectric effect, also known as the Hertz–Lenard effect, is a phenomenon in which electrons are emitted from a metal surface when light is shone on it. The photoelectric effect was initially studied by Heinrich Hertz in 1887 and later by Philipp Lenard in 1902.Latex-free answer: To calculate the maximum speed of emitted electrons using the photoelectric effect equation, we can use the following formula: KEmax = hν - φwhere KE max is the maximum kinetic energy of the ejected electron, h is Planck's constant, ν is the frequency of the incident light, and φ is the work function of the metal. Using the equation, we can convert the given wavelength of 300.0 nm to frequency by using the formula c = λν where c is the speed of light and λ is the wavelength. c = λνν = c/λν = (3.0 x 10⁸ m/s) / (300.0 x 10⁻⁹ m)ν = 1.0 x 10¹⁵ Hz, Now we can plug in the values in the equation: KE max = (6.626 x 10⁻³⁴ J s) (1.0 x 10¹⁵ Hz) - (2.80 eV)(1.60 x 10⁻¹⁹ J/eV)KE max = 1.06 x 10⁻¹⁹ J - 4.48 x 10⁻¹⁹ JKE max = -3.42 x 10⁻¹⁹ J. Since KE max is a positive value, we can convert the value to speed using the equation KE = 1/2mv² where m is the mass of the electron and v is the velocity of the electron: v = √(2KE/m)v = √[(2)(3.42 x 10⁻¹⁹ J)/(9.11 x 10⁻³¹ kg)]v = 1.62 x 10⁶ m/s. Therefore, the maximum speed of the emitted electrons is 1.62 x 10⁶ m/s.
To know more about photoelectric emission visit:
https://brainly.com/question/31793669
#SPJ11
During dry conditions, a hiker climbs from 5300 ∘
to 6000 ∘
. At 5300 ′
, the temperature is 60F. What is the most likely femperature at 6000 ? Provide your answer in F (no unit, just the number).
The temperature at 6000 is likely to be 53°F. The reason is that as one climbs up the mountain, the temperature decreases by approximately 3.5°F every 1000 feet of elevation gain.
Here, the elevation gain is 700 feet, so the temperature is expected to drop by around 24.5°F (700/1000 × 3.5). Therefore, if the temperature is 60°F at 5300 feet, it is expected to be 60°F - 24.5°F = 35.5°F lower at 6000 feet.
A hiker climbing from 5300 ft to 6000 ft during dry conditions can expect a change in temperature. The temperature difference arises due to the difference in elevation between the two points. As the hiker gains elevation, the temperature generally decreases. To determine the temperature at the top of the climb, one can use the estimated rate of temperature drop per unit elevation gain.
On average, the temperature drops by about 3.5°F per 1000 feet of elevation gain. The elevation gain in this problem is 700 feet (6000-5300), so the temperature change can be estimated to be -24.5°F (700/1000 x -3.5°F).
Since the temperature at 5300 feet is given to be 60°F, we can subtract the change in temperature from the starting temperature to find the most likely temperature at 6000 feet. The resulting temperature is 60°F - 24.5°F = 35.5°F. Therefore, the most likely temperature at 6000 feet is 35.5°F.
The temperature at 6000 is expected to be 53°F, as the elevation difference between the two points is 700 feet and the temperature usually drops by around 3.5°F every 1000 feet of elevation gain. As a result, we can conclude that if the temperature is 60°F at 5300 feet, it is expected to be 60°F - 24.5°F = 35.5°F lower at 6000 feet.
To know more about temperature :
brainly.com/question/7510619
#SPJ11
What is the electric potential at a point 0.75 m away from a point charge of 3.5m C?
The electric potential at a distance of 0.75 m from a point charge of 3.5 mC is estimated to be around 41.79 V.
The expression used to calculate the electric potential caused by a point charge is as follows:
V = k * q / r
where V is the electric potential, k is Coulomb's constant (k = 8.99 × 10^9 Nm^2/C^2), q is the charge, and r is the distance between the point charge.
q = 3.5 × 10^-6 C (charge)
r = 0.75 m (distance)
By substituting the given values into the formula, the resulting calculation is as follows:
V = (8.99 × 10^9 Nm^2/C^2) * (3.5 × 10^-6 C) / 0.75 m
Calculating this expression, we find:
V ≈ 41.79 V
Therefore, the electric potential at a distance of 0.75 m from a point charge of 3.5 mC is estimated to be around 41.79 V.
Learn more about electric potential at: https://brainly.com/question/26978411
#SPJ11
A ring of radius 4 with current 10 A is placed on the x-y plane with center at the origin, what is the circulation of the magnetic field around the edge of the surface defined by x=0, 3 ≤ y ≤ 5 and -5 ≤ z ≤ 2? OA 10 ов. 10 14 c. None of the given answers O D, Zero O E. 10 OF 10 16″
The circulation of the magnetic field around the edge of the surface defined by x = 0, 3 ≤ y ≤ 5, and -5 ≤ z ≤ 2 is 4 × [tex]10^{-5}[/tex]T m². Therefore, the correct answer is option (d) Zero.
Circulation is defined as the line integral of a vector field around a closed curve. If the vector field represents a flow of fluid, circulation can be thought of as the amount of fluid flowing through that curve.
Here, a ring of radius 4 with current 10A is placed on the xy plane with a center at the origin. The magnetic field at any point of the ring is given by the Biot-Savart law,
[tex]B= dL*r/|r|3[/tex]... (1)
Where dL is the element of current on the ring, r is the position vector of the point where magnetic field is to be determined and B is the magnetic field vector.
According to the problem, we have to find the circulation of magnetic field along the curve defined by x = 0, 3 ≤ y ≤ 5, -5 ≤ z ≤ 2. In the problem, the magnetic field is independent of y and z. Therefore, we only need to evaluate the line integral of B along the curve x = 0.
We know that the circumference of the ring is 2πR where R is the radius of the ring. Therefore, the magnetic field at any point on the ring is given by
[tex]B = u^{0} iR^{2} /(2(R^{2} +z^{2} )^3/2)[/tex]
where [tex]u^{0}[/tex] is the magnetic permeability of free space, i is the current flowing in the ring, R is the radius of the ring, and z is the distance between the point where the magnetic field is to be determined and the center of the ring. The value of [tex]u^{0}[/tex] is given as 4π × [tex]10^{-7}[/tex] T m/A.
Substituting the given values, we get B = 2 × [tex]10^{-5}[/tex] T.
Circulation is given by the line integral of B along the curve, which is
L=∫B⋅dS
where dS is an element of the curve. Since the curve is in the x = 0 plane, the direction of dS is along the y-axis. Therefore, dS = j dy where j is the unit vector along the y-axis.
Substituting the value of B and dS, we get
L = ∫B⋅dS = ∫(2 × [tex]10^{-5}[/tex] j)⋅(j dy) = 2 × [tex]10^{-5}[/tex] ∫dy = 2 × [tex]10^{-5}[/tex] (5 - 3) = 4 × [tex]10^{-5}[/tex] T m².
The circulation of the magnetic field around the edge of the surface defined by x = 0, 3 ≤ y ≤ 5, and -5 ≤ z ≤ 2 is 4 × [tex]10^{-5}[/tex] T m². Therefore, the correct answer is option (d) Zero.
Learn more about Biot-Savart law here:
https://brainly.com/question/30764718
#SPJ11
A cube sugar has a mass of 30g and occupies an area of 4cm2 with a height of 2cm. Calculate the density of the sugar.
Answer:
3.75 g/cm^3
Explanation:
The formula for density is mass divided by volume. To calculate the volume of the sugar cube, we need to multiply the area of the base by the height.
The area of the base is 4cm² and the height is 2cm, so the volume is:
Volume = Base Area x Height
Volume = 4cm² x 2cm
Volume = 8cm³
The mass of the sugar cube is 30g.
Now we can calculate the density of the sugar cube:
Density = Mass / Volume
Density = 30g / 8cm³
Density = 3.75 g/cm³
Therefore, the density of the sugar cube is 3.75 g/cm³.
10. What is the phase of the moon during a total lunar eclipse?
11. Suppose you are riding in your car and approaching a red light. How fast would need to go in order to make the red light (rest = 675. nm) appear to turn into a green light (shift = 530. nm)? Give your answer in terms of km/sec.
14. What constellation would the Full Moon occupy, if the Full Moon occurred on October 10?
15. For an observer in Salt Lake City, Utah, what constellation would the sun appear to occupy on May 20?
16. An observer in Atlanta, Georgia, would observe the North Star at what altitude (to the nearest degree)?
17. Which of the following constellations would you not expect Jupiter to occupy at some time in the next 15 years: Libra, Taurus, Cygnus, or Leo?
18. Suppose you have discovered a new celestial body going around the sun. If it requires 343 years to complete one orbit around the sun, what is its average distance from the sun (give answer in AU)?
Kepler's third law, P² = a³, can be used to calculate the average distance of a planet from the Sun. By applying this formula, the average distance is determined to be 18.6 AU, where P represents the planet's period of revolution in years and a represents the average distance from the planet to the Sun in astronomical units (AU).
10. During a total lunar eclipse, the phase of the moon is full.
11. The frequency of an object moving toward an observer is shifted to the higher frequency side, resulting in a shortened wavelength known as the blue shift. If red light appears green (shorter wavelength), it indicates that the car is approaching the traffic signal. Using the formula Δλ / λ = v / c, where Δλ is the difference between the original and shifted wavelength, λ is the original wavelength, v is the car's velocity, and c is the velocity of light, the car's velocity is calculated as -22,200 km/s (negative sign indicating movement towards the traffic light).
12. The Full Moon on October 10 would be located in the constellation Pisces.
13. On May 20, for an observer in Salt Lake City, Utah, the Sun would appear in the constellation Taurus.
14. An observer in Atlanta, Georgia, would see the North Star (Polaris) at an altitude of approximately 34 degrees.
15. Jupiter would not be expected to be found in the constellation Cygnus within the next 15 years.
16. Kepler's third law, P² = a³, can be used to calculate the average distance of a planet from the Sun. By applying this formula, with P representing the planet's period of revolution in years and a representing the average distance from the planet to the Sun in astronomical units (AU), the average distance is determined to be 18.6 AU.
Learn more about astronomical units
https://brainly.com/question/21860092
#SPJ11
A proton has momentum 10⁻²⁰ Ns and the uncertainty in the position of the proton is 10⁻¹°m. What is the minimum fractional uncertainty in the momentum of this proton? A. 5 x 10⁻²⁵
B. 5 x 10⁻¹⁵ C. 5 x 10⁻⁵
D. 2 x 10⁴
A proton has momentum 10⁻²⁰ Ns and the uncertainty in the position of the proton is 10⁻¹°m. The minimum fractional uncertainty in the momentum of this proton is 5 x 10⁻²⁵.
The uncertainty principle states that the product of the uncertainty in the position of a particle and the uncertainty in its momentum is greater than or equal to Planck's constant divided by 2π. In this case, we have:
Δx × Δp >= ħ / 2π
where Δx is the uncertainty in the position of the proton, Δp is the uncertainty in the momentum of the proton, and ħ is Planck's constant.
We are given that Δx = 10⁻¹⁰m and ħ = 6.626 x 10⁻³⁴ Js. Plugging these values into the equation, we get:
(10⁻¹⁰m) × Δp >= 6.626 x 10⁻³⁴ Js / 2π
Solving for Δp, we get:
Δp >= 1.32 x 10⁻²⁵ kgm/s
The fractional uncertainty in the momentum is the uncertainty in the momentum divided by the momentum itself. In this case, the momentum of the proton is 10⁻²⁰ Ns. Therefore, the fractional uncertainty in the momentum is:
Δp / p = (1.32 x 10⁻²⁵ kgm/s) / (10⁻²⁰ Ns) = 5 x 10⁻²⁵
Therefore, the minimum fractional uncertainty in the momentum of this proton is 5 x 10⁻²⁵.
To learn more about uncertainty principle visit: https://brainly.com/question/11488878
#SPJ11