if two sacks, one twice as heavy as the other, are lifted the same vertical distances in the same time, how does the power required for each compare?

The heat developed per hour by an 120V electric iron that draws 3.44A current is 1,485,120 Joules.

The Heat is calculated by Heat = Current * Voltage

By substituting the values of Current and Voltage,

Heat = 3.44 A *120 V

Heat = 412.8 J

Therefore, an electric iron drawing 3.44 A of current will develop 412.8 J of heat.

Now we can use the power and time values to calculate the amount of heat developed per hour:

Time = 1 hour = 3600 seconds

Energy = Power *Time

= 412.8 W *3600 s

= 1,485,120 J

Therefore, the amount of heat developed by the electric iron in one hour is 1,485,120 Joules.

To practice more question related to 'heat':

https://brainly.com/question/28566557

#SPJ11

If the rate of internal energy dissipation in a battery is 1.0 watt, and the current produced by the battery is 0.50 amps, the internal resistance of the battery can be calculated using Ohm's law. Ohm's law states that the current through a conductor between two points is directly proportional to the voltage across the two points. The proportionality constant is called the resistance of the conductor, which is expressed mathematically as V = IR, where V is the voltage, I is the current, and R is the resistance.

The power dissipated by the internal resistance of a battery is given by P = I2R, where P is the power, I is the current, and R is the internal resistance. The rate of internal energy dissipation in the battery is given as 1.0 watt, and the current produced by the battery is given as 0.50 amps.

Using Ohm's law, we can calculate the voltage across the battery as V = IR = 0.50 x R. Therefore, the power dissipated by the internal resistance of the battery is P = I2R = (0.50)2 x R = 0.25R.

Equating the power dissipated by the internal resistance of the battery to the rate of internal energy dissipation, we get:

0.25R = 1.0

Solving for R, we get:

R = 1.0/0.25 = 4 ohms.

Therefore, the internal resistance of the battery is 4 ohms.

Internal energy dissipation is the energy that is lost due to friction or resistance in a system. In the case of a battery, internal energy dissipation refers to the energy that is lost due to the internal resistance of the battery. The internal resistance of a battery is a measure of how much energy is lost due to the resistance of the battery's internal components. The higher the internal resistance of the battery, the more energy is lost as heat, which reduces the battery's efficiency.

To know more about Internal energy dissipation refer here:

https://brainly.com/question/15331125#

#SPJ11

The magnitude of the force experienced by the electron is 1.92 x 10^-14 N.

The force experienced by a charged particle moving in a magnetic field is given by the formula,

F = qvB

where F is the force on the particle, q is the charge of the particle, v is the velocity of the particle, and B is the magnetic field.

In the given problem, the electron is moving parallel to the magnetic field, so the angle between the velocity vector and the magnetic field vector is 0 degrees. Therefore, the sine of the angle is 0, and the force experienced by the electron is simply,

F = qvB

where q is the charge of the electron (-1.6 x 10^-19 C), v is the speed of the electron (3 x 10^4 m/s), and B is the magnetic field (0.4 T).

Substituting the given values,

F = (-1.6 x 10^-19 C) * (3 x 10^4 m/s) * (0.4 T)

F = -1.92 x 10^-14 N

To know more about magnetic field, here

brainly.com/question/28246026

#SPJ4

In the metric system, air pressure is measured in pascals. One pascal is equal to a force of one newton per square meter.

Air pressure can be measured using different units. Pascal is a unit of pressure, defined as one newton per square meter. This unit is named after Blaise Pascal, a French mathematician, physicist, and philosopher who made important contributions to the fields of hydrodynamics and hydrostatics.

In the US customary system, air pressure is measured in pounds per square inch (psi), while in the International System of Units (SI), it is measured in pascals (Pa). The unit psi is used to measure pressure in liquids and gases, and it is defined as the amount of pressure exerted by a force of one pound-force per square inch.

Learn more about pascal unit at https://brainly.com/question/30777634

#SPJ11

The linear velocity of water in the aquifer is 0.35 m/day if the specific discharge is 0.35 m/day.

Linear velocity, often known as tangential velocity or tangential speed, refers to the rate at which an object travels in a straight line around a circular path.

Average linear velocity is defined as the ratio of discharge to cross-sectional area. The formula for average linear velocity is as follows: V = Q/A Where: V = Average linear velocity Q = DischargeA = Cross-sectional area. Substitute the given values of discharge in the above equation to find the average linear velocity of water in the aquifer.

Read more about the topic of velocity:

https://brainly.com/question/80295?source=archive

#SPJ11

According to Newton's Law of Gravity, the force of gravity between two objects is inversely proportional to the square of the distance between them. Therefore, when the distance between two objects is increased by a factor of 4, the force of gravity between them will be reduced by a factor of 16.

According to Newton's law of gravity, if two objects are separated so that they end up four times farther from each other than they started, the force of gravity between them will decrease by a factor of 16 (4^2). In other words, the force of gravity is inversely proportional to the square of the distance between the two objects.

Learn more about Newton's Law of Gravity at: https://brainly.com/question/13908515

#SPJ11

The net force acting on the box is 18 N

The net force acting on the box is the vector sum of forces f1 and f2. The net force is given by the formula:
F_net = F_1 + F_2

where F_net is the net force and F_1 and F_2 are the individual forces.

F_1 has a magnitude of 7 N and F_2 has a magnitude of 11 N. Therefore, the net force, F_net, has a magnitude of 18 N and can be expressed as:
F_net = 7 N + 11 N = 18 N

This means that the box is experiencing a net force of 18 N.

Imagine two arrows pointing in opposite directions, with the magnitude of each arrow indicating the magnitude of the respective force. When added together, the arrows should result in an arrow with a magnitude of 18 N.

This new arrow indicates the direction and magnitude of the net force acting on the box.

The net force is calculated by adding the vectors F_1 and F_2. This is done by adding the x and y components of each vector.

In this example, both F_1 and F_2 are in the same direction, so only the magnitudes are added to get the net force.

This is how it works: F_net = 7 N + 11 N = 18 N.

The net force acting on the box is 18 N and is the vector sum of forces f1 and f2.

to know more about Force refer here:

https://brainly.com/question/13191643#

#SPJ11

However, in general, acid rain is formed when sulphur dioxide (SO2) and nitrogen oxides (NOx) are emitted into the atmosphere by human activities, such as burning fossil fuels.

The erroneous statement among the following is : Acid rain is largely because to oxides of nitrogen and sulphur The greenhouse effect is to blame for the world's warming. Infrared radiation from the sun cannot reach earth due to the ozone layer.

Nitric and sulphuric acids are created when the gases nitrogen oxides and sulphur dioxide interact with the minute droplets of water in clouds. The rain from these clouds falls as very weak acid known as 'Acid rain'.

To know more about radiation visit:-

https://brainly.com/question/28202771

#SPJ1

Question:

"Which two of the following statements are true about the chemical reaction that forms acid rain?

a. Sulfur dioxide and nitrogen oxides react with water to form sulfuric acid and nitric acid.

b. Acid rain can cause damage to buildings and statues made of limestone or marble.

c. Acid rain is only a problem in areas with a high population density.

d. Acid rain has no effect on freshwater ecosystems."

Explanation:

The odor of trash is due to the presence of particles emitted by decomposing organic matter. During the summer months, the increased temperature causes particles to move faster and collide with each other more frequently. This results in the particles spreading out further, and the odor from the trash becoming more noticeable.

The kinetic energy of the particles in the trash increases with higher temperatures, which means that they move faster and are more likely to escape from the garbage can into the surrounding air. The heat from the sun also speeds up the process of decomposition, leading to the release of more particles and the generation of a stronger odor.

In contrast, during the winter months, the lower temperatures cause the particles to move more slowly, and they collide with each other less frequently. This results in the particles staying closer to the source and the odor from the trash being less noticeable.

In summary, particle energy plays a crucial role in the smell of trash. The higher the temperature, the more kinetic energy the particles have, which leads to faster movement and more frequent collisions. This results in the particles spreading further and generating a stronger odor. Conversely, lower temperatures slow down particle movement, leading to fewer collisions and less noticeable odor.

Answer:

Particle energy play a role in smell because during the summer, the sun's rays are more powerful and can break down more molecules in the air, leading to a stronger smell. In the winter, the sun's rays are weaker and can't break down as many molecules, leading to a weaker smell.

The rotational inertia of an object depends on its mass distribution and shape relative to the axis of rotation. To calculate the rotational inertia of the system, we would need to know the shapes and masses of the rotating arm and sliding masses.

Rotational inertia depends on the object's mass distribution and the axis of rotation. The greater the object's mass is concentrated away from the axis of rotation, the greater the rotational inertia. The moment of inertia of a rigid body is defined as the sum of the products of the mass of each particle in the body and the square of its distance from the axis of rotation.

Rotational inertia plays a crucial role in many physical phenomena involving rotation, such as the behavior of rotating machines, the motion of planets and stars, and the stability of objects in motion. Understanding rotational inertia is essential for designing efficient and effective machines and for predicting the behavior of rotating systems.

To learn more about Rotational inertia visit here:

brainly.com/question/30856540

#SPJ4

This is an example of the ideal gas law, which is a combination of the three laws of thermodynamics.

The ideal gas law relates the pressure, volume, temperature, and number of particles in a gas:

PV = nRT

where;

When the car is driven, the friction between the tires and the road causes the tires to heat up. As the temperature of the air inside the tires increases, the gas particles move faster and collide more frequently with the tire walls, causing the pressure inside the tires to increase.

According to the ideal gas law, an increase in temperature causes an increase in pressure, assuming that the volume and number of particles remain constant. Therefore, the expansion of the tires due to heating is an example of the ideal gas law.

Learn more about ideal gas law here: https://brainly.com/question/12873752

#SPJ1

The length of the nichrome wire that has the same resistance as the 12.0-meter copper wire is approximately [tex]\( 0.13 \, \text{m} \)[/tex].

To find the length of the nichrome wire that has the same resistance as the 12.0-meter copper wire, we can use the formula for resistance:

[tex]\[ R = \frac{{\rho \cdot L}}{{A}} \][/tex]

where [tex]\( R \)[/tex] is the resistance, [tex]\( \rho \)[/tex] is the resistivity, [tex]\( L \)[/tex] is the length of the wire, and [tex]\( A \)[/tex] is the cross-sectional area.

Given:

Length of the copper wire, [tex]\( L_c = 12.0 \, \text{m} \)[/tex]

Resistance of the copper wire, [tex]\( R_c = 1.50 \, \Omega \)[/tex]

Resistivity of copper, [tex]\( \rho_c = 1.7 \times 10^{-8} \, \Omega \cdot \text{m} \)[/tex]

Resistivity of nichrome, [tex]\( \rho_n = 1.5 \times 10^{-6} \, \Omega \cdot \text{m} \)[/tex]

Let's calculate the cross-sectional area of the copper wire using the resistance formula:

[tex]\[ A_c = \frac{{\rho_c \cdot L_c}}{{R_c}} \]\\\\\ A_c = \frac{{1.7 \times 10^{-8} \cdot 12.0}}{{1.50}} \\\\= 1.36 \times 10^{-7} \, \text{m}^2 \][/tex]

Next, we can use the resistance formula to find the length of the nichrome wire:

[tex]\[ R_n = \frac{{\rho_n \cdot L_n}}{{A_c}} \][/tex]

We need to solve for [tex]\( L_n \)[/tex]:

[tex]\[ L_n = \frac{{R_n \cdot A_c}}{{\rho_n}} \][/tex]

Substituting the given values:

[tex]\[ L_n = \frac{{1.50 \cdot 1.36 \times 10^{-7}}}{{1.5 \times 10^{-6}}} \\\\= 0.13 \, \text{m} \][/tex]

Therefore, the length of the nichrome wire that has the same resistance as the 12.0-meter copper wire is approximately [tex]\( 0.13 \, \text{m} \)[/tex].

Know more about nichrome wire:

https://brainly.com/question/31111150

#SPJ12

A 2.0 m tall man is 10 m in front of a camera with a 25 mm focal length lens, the height of the image on the detector is approximately 5.01 mm.

To determine the height of the image of a 2.0 m tall man who is 10 m in front of a camera with a 25 mm focal length lens, we will use the lens formula and magnification formula.

First, let's use the lens formula: 1/f = 1/u + 1/v

Here, f is the focal length, u is the object distance, and v is the image distance. We have f = 25 mm, and u = 10 m (which we need to convert to millimeters, so u = 10,000 mm).

We can now solve for v: 1/25 = 1/10,000 + 1/v

To isolate v, let's first subtract 1/10,000 from both sides: 1/25 - 1/10,000 = 1/v Now,

find the least common denominator (LCD) and subtract: (400 - 1)/10,000 = 1/v 399/10,000 = 1/v

Now, take the reciprocal of both sides to solve for v: v = 10,000/399

Now that we have the image distance (v), we can use the magnification formula to find the height of the image: magnification (m) = image height (h') / object height (h) = v / u

We want to find h', so we can rearrange the formula: h' = h * (v / u)

Plug in the known values (h = 2.0 m, u = 10,000 mm, and v = 10,000/399 mm), and convert h to mm (2.0 m = 2,000 mm): h' = 2,000 * (10,000 / 399) / 10,000 Simplify the expression: h' = 2,000 / 399

So, the height of the image on the detector when the man is 2.0m tall, 10 m in front of a camera with a 25 mm focal length lens is approximately 5.01 mm.

To know more about focal length refer here:

https://brainly.com/question/16188698#

#SPJ11

The time it takes for the potential difference across the capacitor to decrease to 5.0 V is 0.035 seconds.

In RC circuits, R represents the resistor, and C represents the capacitor.

A capacitor is a device that stores electric charge, whereas a resistor is a device that resists electric current.

The formula for charging and discharging a capacitor is:

V = V0 (1-e^(-t/RC)),

where V0 is the voltage at the capacitor's beginning, V is the voltage at time t, R is the resistor, and C is the capacitor's capacitance.

To determine the time required for the potential difference across the capacitor to decrease to 5.0 V, the formula for the time constant is

RC.t = RC ln (V0/V)

To calculate the time constant, we need to know the resistance, capacitance, and initial voltage of the capacitor. Let us assume the following values:

C = 50 x 10^-6 F = 5.0 V

The capacitance of the capacitor is 50 x 10^-6 F, and the voltage across the capacitor is 5.0 V.

Substitute the values into the formula:

T = RC ln (V0/V) = 1000 Ω * 50 x 10^-6 F ln (10 V / 5 V) = 0.035 seconds.

Therefore, the time it takes for the potential difference across the capacitor to decrease to 5.0 V is 0.035 seconds.

To know more about capacitor click here:

https://brainly.com/question/17176550

#SPJ11

The voltage across the inductor during the period when the current changes at 9.1 A/ms with an inductance of 26 mH is 236.6 V.

An inductor is an electrical component that stores energy in a magnetic field when a current passes through it. An inductor is a device that opposes any change in the current flowing through it. The inductor is represented by the symbol L and is measured in henries (H).

The difference in electrical potential between two points in a circuit is known as voltage. The unit of voltage is volts (V).

The voltage across an inductor can be calculated using the formula:

[tex]v = L(di/dt)[/tex]

where v is the voltage, L is the inductance, and [tex]di/dt[/tex] is the rate of change of current.

Substituting the given values, we get:

[tex]v = 26\  mH \times (9.1 \ A/ms)[/tex]

Note that the units for inductance and rate of change of current must be consistent, so we convert the inductance to henries (H) and the rate of change of current to amps per second (A/s):

[tex]v = 0.026\  H \times (9100 \ A/s)[/tex]

[tex]v = 236.6 \ V[/tex]

Therefore, the voltage across the inductor during this period is 236.6 V.

Learn more about inductance:

https://brainly.com/question/30216563

#SPJ11

The number of teeth on the driven gear is 14 and the theoretical center-to-center distance is 3.34 inches.

Speed Ratio: Speed Ratio = (Number of Teeth on Driven Gear)/(Number of Teeth on Driving Gear). The Speed Ratio = 1400 rev/min/2100 rev/min = 0.6667.

Therefore, the number of teeth on the driven gear = (Number of Teeth on Driving Gear) x (Speed Ratio) = 20 x 0.6667 = 13.33. Rounding up, we can conclude that the number of teeth on the driven gear is 14.

The next step is to find the theoretical center-to-center distance. To do this, we need to use the formula for calculating Pitch Diameter: Pitch Diameter = (Number of Teeth)/(Diametral Pitch).

In this case, the Pitch Diameter of the driving gear is (20 teeth)/(12 teeth/in) = 1.67 inches. Therefore, the center-to-center distance = Pitch Diameter x 2 = 1.67 inches x 2 = 3.34 inches.

Hence the number of teeth on the driven gear is 14 and the theoretical center-to-center distance is 3.34 inches.

to know more about distance refer here:

https://brainly.com/question/15172156#

#SPJ11

The speed of the boat in still water is 34 km/h, and the speed of the stream's current is 8 km/h.

Let's denote the speed of the boat in still water as v and the speed of the stream's current as c.

When the boat travels downstream, its speed relative to the shore is the sum of its speed in still water and the speed of the current. So, we have:

v + c = 84 km/2 h = 42 km/h

When the boat travels upstream, its speed relative to the shore is the difference between its speed in still water and the speed of the current. So, we have:

v - c = 130 km/5 h = 26 km/h

We can now solve this system of equations to find v and c. Adding the two equations, we get:

2v = 68

v = 34 km/h

Substituting v into one of the equations, we can solve for c:

v + c = 42

34 + c = 42

c = 8 km/h

Learn more about  speed of the stream's at: https://brainly.com/question/2292122

#SPJ11

The sun's magnetic field is responsible for the sun's surface and atmospheric activity. The correct option is "The sun's magnetic field."The sun's magnetic field plays a vital role in the surface and atmospheric activity of the sun.

The sun is considered a magnetized body that possesses a strong magnetic field. Magnetic fields are present in every part of the sun, from the core to the atmosphere, and they play a crucial role in the sun's structure, dynamics, and atmosphere.The sun's magnetic field is responsible for the following phenomena:

Sunspots are dark areas on the surface of the sun that are cooler than the surrounding areas, but they are still very hot. They arise because of the interaction between the sun's magnetic field and the sun's plasma.Auroras occur when charged particles from the sun collide with particles in the Earth's atmosphere, and the interaction between the particles' magnetic fields produces a beautiful display of light in the sky.

The corona, which is the sun's outermost layer, is hotter than the layers below it. The sun's magnetic field is thought to be responsible for the heating.

for such more question on magnetic field

https://brainly.com/question/14411049

#SPJ11

An effective informational brochure for an early child-care facility should be informative, visually appealing, and easy to understand, providing essential information about the facility and the services it provides to parents, caregivers, and other stakeholders.

An informational brochure that is appropriate for posting within an early child-care facility should include the following important features:

Clear and concise information: The information in the brochure should be easy to understand and presented in a simple language that parents, caregivers, and other stakeholders can understand.

Engaging visuals: The brochure should be visually appealing with engaging pictures, graphics, or illustrations that capture the attention of parents and caregivers.

Overview of the facility: The brochure should provide an overview of the early child-care facility, including the services offered, the age groups served, and the operating hours.

Staff credentials: The brochure should highlight the credentials of the staff, including their education, experience, and training.

Curriculum and activities: The brochure should provide details about the curriculum and activities offered by the facility, including the approach used to support children's learning and development.

Health and safety: The brochure should outline the health and safety measures in place to ensure the well-being of the children, including policies on illness, emergency procedures, and first aid.

Parent involvement: The brochure should highlight opportunities for parent involvement, including ways that parents can support their child's learning at home.

Fees and payment options: The brochure should provide information on the fees and payment options available to parents, including any financial assistance programs that may be available.

Contact information: The brochure should include contact information for the facility, including phone numbers, email addresses, and physical address, so that parents and caregivers can easily get in touch if they have questions or concerns.

Learn more about Child care facility:https://brainly.com/question/11401871

#SPJ1

The acceleration due to gravity in m/s² at that altitude of 744 km is 9.797.

To find out what the acceleration due to gravity is in m/s² at an altitude of 744 km above the surface of earth, use the formula `g = Gm/r²`.

Given,The altitude of the satellite, h = 744 km,The radius of the earth, r = 6371 km, Formula for acceleration due to gravity:

g = Gm/r²

Here, the value of G, the universal gravitational constant, is 6.67 x 10^-11 Nm²/kg².Mass of the Earth, m = 5.97 x 10^24 kg.Let's calculate the radius of the orbit, R.Radius of the orbit = r + h= 6371 + 744 = 7115 km = 7.115 x 10^6 m.So, we have,

g = Gm/R²= 6.67 x 10^-11 x 5.97 x 10^24 / (7.115 x 10^6)²= 9.797 m/s².Therefore, the acceleration due to gravity in m/s² at that altitude is 9.797.

More on acceleration: https://brainly.com/question/21975712

#SPJ11

The student added 1,700,000 Joules of heat to the water.

What is Specific Heat?

Specific heat is the amount of heat energy required to raise the temperature of one unit mass of a substance by one degree Celsius (or Kelvin) without any change in phase. It is a physical property of a substance that is unique to each material and depends on its molecular structure and composition. The specific heat of water, for example, is 4.18 J/g°C, which means that it takes 4.18 joules of energy to raise the temperature of one gram of water by one degree Celsius.

The heat added to the water can be calculated using the formula:

Q = m * c * ΔT

where Q is the heat added, m is the mass of the water, c is the specific heat of water, and ΔT is the change in temperature.

Substituting the given values:

m = 5 kg

c = 4,000 J/kg°C

ΔT = (100°C - 15°C) = 85°C

Q = 5 kg * 4,000 J/kg°C * 85°C = 1,700,000 J

Therefore, the student added 1,700,000 Joules of heat to the water.

Learn more about Specific Heat from given link

https://brainly.com/question/27991746

#SPJ1

The effective spring constant can be expressed in terms of k1 and k2 as:

k = k1k2 / (k1 + k2).

The effective spring constant k of the two-spring system can be expressed in terms of k1 and k2.

There are two cases for springs connected in series.

They are given as follows:

Case 1: Two springs have the same spring constant, k1 = k2 = k

In this case, the springs are identical and have the same spring constant k.

The effective spring constant for two springs connected in series can be calculated as:

k = k1 + k2 = k + k = 2k

Therefore, the effective spring constant is 2k

Case 2:

Two springs have different spring constants, k1 ≠ k2In this case, the springs have different spring constants k1 and k2.

The effective spring constant for two springs connected in series can be calculated as follows:

1/k = 1/k1 + 1/k2k = k1k2 / (k1 + k2)

Therefore, the effective spring constant can be expressed in terms of k1 and k2 as:

k = k1k2 / (k1 + k2).

Learn more about effective spring at

https://brainly.com/question/29851511

#SPJ11

After the collision, the first cart moves to the left with a velocity of -1.5 m/s and the second cart moves to the right with a velocity of 1.5 m/s.

The velocities of the two carts after collision can be determined using the conservation of momentum principle. Momentum is defined as the product of an object's mass and velocity. Given,Mass of each cart, m = 0.5 kg, Initial velocity of each cart, u = 1.5 m/s, Initial momentum of each cart, p = mu.

After collision, velocity of the carts = v. Using the law of conservation of momentum;

mu + mu = mv + mv⇒ 2mu = 2mv⇒ u = v

Momentum before collision = Momentum after collision (conservation of momentum)

∴ 0.5 × 1.5 + 0.5 × (-1.5) = 0.5v1 + 0.5v2

On solving, we get,v1 = -1.5 m/sv2 = 1.5 m/s

Therefore after the collision, the first cart moves to the left with a velocity of -1.5 m/s and the second cart moves to the right with a velocity of 1.5 m/s.

More on velocity: https://brainly.com/question/30470329

#SPJ11

We must use the mechanical advantage formula to determine the length of the ramp:

Output force minus Input force equals Mechanical Advantage (MA). In this instance, the input force is the force required to hoist the object in the absence of the ramp, and the output force is the weight of the object being raised up the ramp

By dividing the length of the slope by its height, you may calculate the optimal mechanical advantage of an inclined plane. The ideal mechanical advantage of a ramp, for instance, is 3 metres 1 metre, or 3 metres, if you are loading a truck that is 1 metre high utilising it.

Basic Machines' Mechanical Advantage and Efficiency Calculated. The IMA is typically calculated as the resistance force (Fr) divided by the effort force (Fe). IMA is also equal to the product of the load's travel distance (d) and the distance over which the effort is applied (de).

To know more about mechanics  visit:-

brainly.com/question/20885658

#SPJ1

The following waves can travel without a medium: visible light, x-rays, and radio waves. Seismic waves and waves on a lake require a medium, such as air or water, to travel through.

Visible light is a form of electromagnetic radiation that is composed of various colors. It can travel through a vacuum, such as the space between planets, and does not require a medium to travel through. X-rays are also electromagnetic radiation, but with a higher frequency than visible light, allowing them to pass through objects that visible light cannot. Radio waves are also a form of electromagnetic radiation, and can travel through a vacuum. Seismic waves, on the other hand, require a medium, such as air or rock, to travel through. These waves are used to measure earthquakes and are created when energy is released from the ground. Similarly, waves on a lake require a medium, such as water, to travel through.

Learn more about the type of waves: https://brainly.com/question/12050819

#SPJ11

When potential energy increases everywhere by a fixed positive value, the force magnitude does not change.

This is because potential energy is a function of position and does not depend on the force acting on the object. However, the rate of change of potential energy concerning displacement (or position) gives the force acting on the object, which is known as the force of the conservative system

Given: The potential energy increases everywhere by a fixed positive value

We know that potential energy is a function of position and does not depend on the force acting on the object.The rate of change of potential energy with respect to displacement (or position) gives the force acting on the object, which is known as the force of the conservative system.

Since the potential energy increases everywhere by a fixed positive value, it means the force magnitude does not change.

To know more about potential energy click here:

https://brainly.com/question/24284560

#SPJ11

The force of gravity acting between the earth and a 125-kg person standing on the surface of the earth is 1226.7N.

This is calculated using Newton's law of universal gravitation, which states that the gravitational force between two objects is equal to the product of their masses, divided by the square of the distance between them, multiplied by the gravitational constant. In this case, the masses of the Earth and the person are both known, and the distance between them is assumed to be the radius of the Earth.

Therefore, the gravitational force between the Earth and the person can be calculated as:

F = (G x ME x Mperson) / (rEarth)²

Where:

Plugging in the values, the gravitational force between the Earth and the person comes out to be 1226.7N.

.

Therefore, the force of gravity between the earth and a 125-kg person standing on the surface of the earth comes out to be 1226.7N.

To know more about the force of gravity, refer here:

https://brainly.com/question/880695#

#SPJ11

The movement of the plates may lead to or cause an earthquake.

At convergent boundaries, two tectonic plates are moving towards each other. There are three types of convergent boundaries, characterized by the type of plates involved: Oceanic-Oceanic Convergence, Oceanic-Continental Convergence, Continental-Continental Convergence.

At divergent boundaries, two tectonic plates are moving away from each other. This type of boundary is often associated with seafloor spreading, where new crust is formed as magma rises to the surface and solidifies. Divergent boundaries on land can result in the formation of rift valleys and volcanoes.

At transform boundaries, two tectonic plates are sliding past each other. These boundaries are characterized by lateral movement and can result in earthquakes

What is plate movement:https://brainly.com/question/3970445

#SPJ1

The current flowing through the wire is 0.15 A.

The force on an 0.8 m wire that is perpendicular to Earth's magnetic field is 0.12 N. This is equal to the equation F=BIL, where B is the magnetic field, I is the current and L is the length of the wire.

Calculate the magnetic force, F, with the equation:

F=BIL, where B is the magnetic field, I is current, and L is the length of the wire.

Calculate the current, I, with the equation I = F/BL = 0.15 A.

Therefore, the current flowing through the wire is 0.15 A.

To know more about current click here:

https://brainly.com/question/16880541

#SPJ11

Neutron stars with a mass of 1.4 solar masses will have around 1.8 x [tex]10^5^7[/tex] neutrons, are composed almost entirely of neutrons and have approximately twice the mass of the sun.

Neutron stars are composed almost entirely of neutrons and have approximately twice the mass of the sun. On average, neutron stars have about 1.4 solar masses, or 2.8 x [tex]10^3^0[/tex] kg. This means that one cubic centimeter of neutron star material has a mass of around 2.2 x [tex]10^1^4[/tex] kg. Each cubic centimeter of neutron star material contains about 1.6 x [tex]10^4^5[/tex] neutrons, or around one hundred trillion trillion neutrons. Thus, a neutron star with a mass of 1.4 solar masses will have around 1.8 x [tex]10^5^7[/tex] neutrons.

For more such questions on Neutron stars.

https://brainly.com/question/28271936#

#SPJ11