in a billiards game, the white cue ball hits the black ball, moving the black ball to the right while the cue ball moves to the left. if the action force is applied by the cue ball to the black ball, which force is the reaction force?

The circuit can be broken down into two sections, one containing bulb R1 and the other containing bulb R2. When bulb R4 is removed from the circuit, there is a break in the wire at its position. As a result, the circuit is broken, and the flow of electricity is halted. As a result, the current in the bulb R2 will be zero.

A circuit is a closed path that allows electricity to flow from one point to another. The electricity that flows through a circuit is referred to as an electric current. Electric current is measured in amperes (A). The bulbs R1 and R2 are connected in parallel to a voltage source, V. In parallel, the voltage across each bulb is the same, and the current flowing through each bulb is inversely proportional to its resistance.

When one bulb is removed from a parallel circuit, the others continue to operate. There is no interruption in the circuit when a bulb is removed from the circuit, and the voltage across the other bulbs remains constant. When bulb R4 is removed from the circuit, the wire is broken, and the circuit is disrupted. As a result, the current flowing through the circuit is halted, and there is no current flow through the bulb R2.

When a parallel circuit is broken, the current in that part of the circuit is disrupted, but the current in the other parts of the circuit continues to flow normally. As a result, bulb R1 will continue to glow, but bulb R2 will not be lit. In summary, the current flowing through the bulb R2 will be zero when the bulb R4 is removed from the circuit, leaving a break in the wire at its position.

To know more about A circuit refer here:

https://brainly.com/question/21505732#

#SPJ11

Answer: If instead you connected the battery to a resistor R/2, it would put out 5 volts.

The voltage put out if a battery connected to a resistor R puts out a voltage of 10 volts and a current of 0.5 amps, and if instead you connected the battery to a resistor R/2 is 5 volts.

The voltage of a battery connected to a resistor R puts out a voltage of 10 volts and a current of 0.5 amps can be found using the Ohm's Law which is:

V = IR

Where V is the voltage, I is the current, and R is the resistance of the resistor.

If you connect the battery to a resistor R/2, it would put out the voltage which can be calculated as follows:

V = IRV = 0.5 × 10V = 5V

Therefore, if instead you connected the battery to a resistor R/2, it would put out 5 volts.




Learn more about volts here:

https://brainly.com/question/29014695#

#SPJ11

An ice skater is spinning about a vertical axis with arms fully extended. If the arms are pulled closer to the body, the angular momentum of the skater will remain constant while the kinetic energy of the skater increases. The correct option is C.

The angular momentum of the skater is given by

[tex]L = I\omega[/tex],

where I is the moment of inertia of the skater and ω is the angular velocity.

When the skater pulls their arms in, their moment of inertia decreases due to the decreased distance between their body and the axis of rotation.

According to the conservation of angular momentum, the product of the moment of inertia and angular velocity must remain constant. Therefore, if the moment of inertia decreases, the angular velocity must increase to keep the angular momentum constant.

The kinetic energy of the skater is given by

[tex]K = (1/2)I\omega^2[/tex]

As the moment of inertia decreases and the angular velocity increases, the kinetic energy of the skater also increases because it is proportional to the square of the angular velocity.

Therefore, the correct answer is: (C) Remains Constant Increases. The angular momentum remains constant, while the kinetic energy increases due to the increased angular velocity.

Learn more about angular momentum:

https://brainly.com/question/4126751

#SPJ11

The work done on the truck by the friction force of the road is -484,000 J. This work is done by the friction force of the road. Therefore, the work done by the friction force of the road is also negative.

To determine the work done by the friction force of the road on the truck, we can use the work-energy principle, which states that the net work done on an object is equal to its change in kinetic energy.

The initial kinetic energy of the truck is:

[tex]K_1 = \frac{1}{2} . m . v_1^2\\K_1= \frac{1}{2} .(2.000 kg). (22 m/s)^2\\K_1 = 484,000 J[/tex]

Since the truck comes to a stop, its final kinetic energy is zero. Therefore, the net work done on the truck is equal to its initial kinetic energy:

[tex]Net work = K_ - K_2\\Net work = 484,000 J - 0\\Net work = 484,000 J[/tex]

The friction force of the road acts opposite to the direction of motion of the truck and causes it to slow down. Therefore, the work done by the friction force is negative:

Work by friction force = -484,000 J

Therefore, the work done on the truck by the friction force of the road is -484,000 J.

Learn more about friction forces at: https://brainly.com/question/23161460

#SPJ11

The statement that is wrong concerning the two tails of a comet is "they are perpendicular to each other." Two tails of a comet can't be perpendicular to each other.

Comets are celestial bodies that circle around the sun, originating from the Kuiper Belt and Oort Cloud. Comets are believed to be made up of ice, rock, and dust, and they can range in size from a few meters to tens of kilometers in diameter. Comets typically consist of two tails: a gas or plasma tail and a dust tail. Two tails of a comet. The two tails of a comet are made up of gas, plasma, and dust. They all point in opposite directions from the comet's nucleus, or core, as it travels through space. The dust tail of a comet is more massive than its ion tail, which is made up of electrically charged particles that are affected by the sun's magnetic field. Both tails of a comet are not perpendicular to each other because they are pointing in opposite directions. A gas tail may be tens or hundreds of thousands of kilometers long. It consists of highly volatile molecules such as water and carbon dioxide that have been energized by the sun's ultraviolet radiation. As they lose energy, the molecules release the energy in the form of light, which is what makes the gas tail visible. A dust tail, on the other hand, consists of tiny grains of rock and dust that have been kicked off the surface of the comet. It's typically much shorter than the gas tail, but it can be much brighter.

To learn more about Comet :

https://brainly.com/question/28102026

#SPJ11

To find how far from the wall the pass will be picked up by the teammate, we will use the property that the angles formed by the path of the puck with the wall are congruent. This means the angle of incidence (the angle at which the puck hits the wall) is equal to the angle of reflection (the angle at which the puck leaves the wall).

Step 1: Identify the angle of incidence, which we will call angle A, and the angle of reflection, which we will call angle B. According to the given information, angle A = angle B.

Step 2: Measure the distance between the hockey player and the wall (let's call this distance "d1") and the distance between the teammate and the wall (let's call this distance "d2").

Step 3: Use trigonometry to find the distance between the hockey player and the point where the puck hits the wall (let's call this distance "x"). You can use the tangent function: tan(angle A) = d1/x.

Step 4: Solve for x: x = d1 / tan(angle A).

Step 5: Use trigonometry again to find the distance between the point where the puck hits the wall and the teammate (let's call this distance "y"). Use the tangent function again: tan(angle B) = d2/y.

Step 6: Solve for y: y = d2 / tan(angle B).

Step 7: Since angle A = angle B, we can now add x and y to find the total distance the pass traveled before being picked up by the teammate: total distance = x + y.

By following these steps, you can calculate how far from the wall the pass will be picked up by the teammate.

To Learn more :

https://brainly.com/question/29087040

#SPJ11

The given values in the equation, F = (0.0147) * (3.09)/0.110F = 0.414 N Thus, the force required to give an angular acceleration of 3.09 m/s² to the solid ball is 0.414 N.

Given, The radius of a solid ball (r) = 0.110 m The mass of the solid ball (m) = 1.88 kg The angular acceleration of the solid ball (α) = 3.09 m/s²Now, we need to find the force required to give an angular acceleration of 3.09 to the solid ball. So, we will use the formula for torque, Torque (τ) = Fr Where, r = radius of the solid ball F = force required to move the solid ball on the edge of the solid ball By using Newton's second law of motion, F = ma Where, m = mass of the solid ball a = angular acceleration of the solid ball By using the formula for torque, Torque (τ) = Frτ = IαWhere, I = moment of inertia of the solid ball By equating both equations, F * r = IαF = Iα/r By using the formula for moment of inertia of a solid ball, I = (2/5)mr²I = (2/5) * 1.88 * 0.110²I = 0.0147 kg m²Now, substituting the given values in the equation, F = (0.0147) * (3.09)/0.110F = 0.414 N Thus, the force required to give an angular acceleration of 3.09 m/s² to the solid ball is 0.414 N.

Learn more about Force

brainly.com/question/13191643

#SPJ11

Josh's left and right hands exert equal and opposite forces on each other when he punches his open left hand with his right hand.

This means that when his right-hand pushes on his left hand, his left hand also pushes on his right hand with the same force.

This is Newton's Third Law of Motion:

"For every action, there is an equal and opposite reaction."

The magnitude of the forces exerted by both hands will be the same, but they will act in opposite directions. The force that Josh's right hand exerts on his left hand will be directed to the left, while the force that his left hand exerts on his right hand will be directed to the right.

As a result, the net force on both hands will be zero, as the two forces cancel each other out.

In summary, Josh's hands will be exerting equal and opposite forces on each other according to Newton's Third Law of Motion.

To know more about forces, refer here:

https://brainly.com/question/13191643#

#SPJ11

The work done to accomplish the task of climbing the stairs oh height 2.50 m is 1848.38 J.

The formula to calculate the work done by a person in climbing the stair is:

W = mgh

where m is the mass, g is the acceleration due to gravity, and h is the height gained.

So, we can calculate the work done by a person in climbing the stairs with the given values.

W = mgh

W = 75.0 kg × 9.81 m/s² × 2.50 m

W = 1848.38 J

Therefore, the work done by a 75.0-kg person to climb stairs gaining 2.50 m in height is 1848.38 J.

Learn more about work here: https://brainly.com/question/25573309.

#SPJ11

The frequency of the standing wave set up by the microwave is 8 GHz (or 8 × 10^9 Hz).

What is Wavelength?

The wavelength of the microwave is 12.2 cm, and the distance between the two parallel walls is 48.8 cm.

frequency is:

f = v/λ

where `v` is the velocity of the wave and `λ` is the wavelength of the wave.

to calculate the velocity of the microwave:

`v = 2dƒ`

where `d` is the distance between the two walls and `ƒ` is the frequency.

Substituting the given values,`

v = 2(0.488)ƒ`.

Rearranging the equation for `ƒ`,

'ƒ = v/2d`.

Substituting `v` and `d` with the values given in the question:

`ƒ = (2 × 0.488) / (2 × 0.122)`.

Simplifying the expression,

`ƒ = 8`.

To know more about wavelength:

https://brainly.com/question/4112024

#SPJ11

Opposition is when a planet is directly opposite the Sun in the sky, as viewed from Earth. Conjunction is when a planet is positioned closest to the Sun in the sky, as viewed from Earth. Greatest elongation is when a planet is at its farthest point away from the Sun in the sky, as viewed from Earth.

For planets closer to the Sun than Earth, opposition occurs when they are in the opposite direction to the Sun in the sky, while conjunction occurs when they are in the same direction as the Sun in the sky. For planets farther from the Sun than Earth, opposition occurs when they are in the same direction as the Sun in the sky, while conjunction occurs when they are in the opposite direction to the Sun in the sky.

At opposition, planets will appear brightest and most visible in the night sky. At conjunction, planets will appear faintest and least visible. At greatest elongation, planets will appear brightest and most visible during the daytime sky.

Know more about planets here:

https://brainly.com/question/29765555

#SPJ11

The event horizon of this black hole is located at a radius of 2.84 km from its center.

The event horizon of a black hole marks the boundary where the escape velocity reaches the speed of light.

The Schwarzschild radius (Rs) of a black hole is the distance from the center of the black hole at which the escape velocity reaches the speed of light. For a 2.30 msun black hole, the Schwarzschild radius is calculated as:


Rs = 2G*M/c2 = 2*(6.674x10-11 m3kg-1s-2) * (2.30x1030 kg) / (3x108 m/s)2 = 2.84 km

The Schwarzschild radius of a 2.30 msun black hole is 2.84 km, meaning this is the distance from the center of the black hole at which the escape velocity reaches the speed of light.

Therefore, the event horizon of this black hole is located at a radius of 2.84 km from its center.

To know more about escape velocity click on below link:

https://brainly.com/question/30302498#

#SPJ11

Answer:

L = L0 (1 - v^2 / c^2)^1/2

L0 is the proper length and L the distance measured by the space traveler

L = L0 (1 - .92^2)^1/2

L = L0 * .39 = 8.6 L-y * .39 = 3.4 L-y     as measured by space traveler

The seesaw moved when a third person pushed down on one side. This is because the seesaw is a simple machine that consists of a long plank balanced in the middle with a pivot point that allows it to move up and down.

When the two students sit on the seesaw in a way that makes it balance and not move, they are evenly distributed on each end. However, when the third person pushes down on one side, this distribution of weight becomes unequal, and the seesaw moves in the direction of the heavier side.

The heavier end of the seesaw moves down while the lighter end moves up. This is because the heavier side creates more force, or torque, on the pivot point, causing the seesaw to tilt towards that side.

As a result, the seesaw moves and is no longer in balance.

Learn more about balance and move at

brainly.com/question/14160688  

#SPJ11 

Answer:

by reducing friction

Explanation:

By reducing friction, a machine can be made more efficient. Friction causes energy loss in a machine, which reduces its efficiency. By reducing friction, less energy is wasted as heat, and more energy is utilized for the intended purpose of the machine.

The seven major divisions of the electromagnetic spectrum are Radio Waves, Microwaves, Infrared Radiation, Visible Light, Ultraviolet Light, X-Rays, and Gamma Rays.

To know more about the electromagnetic spectrum, refer here:

https://brainly.com/question/23727978#

#SPJ11

The charge stored on the capacitor is 702 × 10^-12 C.

A capacitor is a device that stores an electric charge. It consists of two conductors separated by an insulator, which is often called a dielectric.

Capacitance is a measure of a capacitor's ability to store an electric charge. It's measured in farads (F) or picofarads (pF).A capacitor stores electrical energy in the form of an electric field.

The charge that is stored on a capacitor depends on the capacitance of the capacitor, as well as the voltage applied across the capacitor. The formula for calculating the charge stored on a capacitor is Q = CV,

where Q is the charge stored on the capacitor, C is the capacitance of the capacitor, and V is the voltage applied across the capacitor.

The capacitance of the capacitor is given as 13 pF and the voltage applied across the capacitor is 54 V.

Q = CVQ = 13 × 10^-12 F × 54 VQ = 702 × 10^-12 CTherefore, the charge stored on the capacitor is 702 × 10^-12 C.

to know more about capacitor refer here:

https://brainly.com/question/17176550#

#SPJ11

For a 2D, incompressible, steady flow, the stream and potential functions are harmonic, which means they satisfy Laplace's equation.

In fluid dynamics, the stream function and potential function are two important scalar fields that describe the behavior of a fluid flow. For a 2D, incompressible, steady flow, it can be shown mathematically that these functions are harmonic, meaning that they satisfy Laplace's equation. This implies that the rate of change of these functions is zero everywhere in the fluid domain. As a result, the streamlines and equipotential lines (lines of constant potential) in the flow field are orthogonal, which is a key property of 2D incompressible flows. The harmonic property of the stream and potential functions also has important implications for the mathematical analysis and numerical simulation of fluid flows.

To know more about flow, here

brainly.com/question/15686116

#SPJ4

a) The greenhouse effect refers to the process by which certain gases in the Earth's atmosphere trap and re-emit heat from the sun, leading to a warming effect on the planet's surface.

These gases, including carbon dioxide, water vapor, methane, and others, act like a blanket around the Earth, absorbing and trapping the sun's radiation and preventing it from escaping into space.

b) Atmospheric water vapor is a key component of the Earth's climate system, as it plays a crucial role in the greenhouse effect. As water vapor absorbs and re-emits radiation from the sun, it helps to trap heat in the atmosphere and keep the planet warm.

However, the amount of water vapor in the atmosphere is strongly influenced by temperature and other factors, which can in turn affect climate patterns and weather events.

c) The increased concentration of carbon dioxide in the atmosphere changes the climate because it enhances the greenhouse effect. Carbon dioxide is a particularly potent greenhouse gas, as it absorbs and re-emits radiation across a range of wavelengths, effectively trapping more heat in the atmosphere. As humans burn fossil fuels and engage in other activities that release carbon dioxide into the air, the concentration of this gas increases, leading to a buildup of heat-trapping gases and a corresponding increase in global temperatures.

d) The melting of continental glaciers and sea ice in polar regions can accelerate the rise in temperature through a process known as positive feedback. As the ice melts, it exposes more land and water, which in turn absorb more solar radiation and heat up. This leads to further melting, which exposes even more land and water, and so on.

Learn more about  The greenhouse effect

https://brainly.com/question/13706708

#SPJ4

The sizes of a byte, short, int, and long are 1,2,4, and 8 bytes, respectively. alignment is restricted so that an n-byte field must be located at an address divisible by n. The total size of array 'a' containing 10 widgets is 160 bytes. Therefore, the correct option is B.

The total size of array 'a' containing 10 widgets can be calculated by first finding the size of a single widget and then multiplying it by the number of widgets in the array.

A single widget has the following fields:
1. short s (2 bytes)
2. byte b (1 byte)
3. long l (8 bytes)
4. int i (4 bytes)

To ensure proper alignment, padding is added to the struct. The size of a widget will be the sum of the sizes of its fields and any required padding.

1. short s (2 bytes): No padding is needed since the address is divisible by 2.
2. byte b (1 byte): Padding of 1 byte is needed, as the next field (long) requires an address divisible by 8. So, after byte b, 1 padding byte is added.
3. long l (8 bytes): No padding is needed, as the current address is divisible by 8.
4. int i (4 bytes): No padding is needed, as the current address is divisible by 4.

Now, let's sum up the sizes of fields and padding:
2 (short) + 1 (byte) + 1 (padding) + 8 (long) + 4 (int) = 16 bytes

Since a single widget occupies 16 bytes, the total size of the array containing 10 widgets will be:
16 (single widget size) x 10 (number of widgets) = 160 bytes
So, the total size of array 'a' containing 10 widgets is 160 bytes, which corresponds to option (b).

To know more about array refer here:

https://brainly.com/question/30726504#

#SPJ11

Explanation:

Insects can show three types of development. One of them, holometaboly (complete development), consists of the stages of egg, larva, pupa and sexually mature adult, which occupy different habitats. Insects with holometaboly belong to the most numerous orders in terms of known species. This type of development is related to a greater number of species due to the a) protection in the pupa stage, favoring the survival of fertile adults. b) production of many eggs, larvae and pupae, increasing the number of adults. c) exploration of different niches, avoiding competition between life stages. d) food intake at all stages of life, ensuring the emergence of adults. e) use of the same food in all stages, optimizing the body's nutrition.

If a truck has a linear acceleration of 1.85 m/s² and the wheels have an angular acceleration of 5.23 rad/s², the diameter of the truck's wheels   0.71 m.

Linear acceleration refers to the time rate of change of linear velocity, whereas angular acceleration refers to the time rate of change of angular velocity. This is the primary differential between linear and angular acceleration. Simply said, changes in an object's linear velocity with respect to time are represented by changes in linear acceleration.

The angular acceleration can be deduced immediately from the concept of α =ΔωΔt because the ultimate angular velocity and time are both provided.

The link between linear acceleration (a) and rotational acceleration is expressed as a = r×α . When the angular acceleration increases, so will the linear acceleration's strength. Increased wheel angular acceleration, for instance, denotes an accelerated vehicle.

Linear acceleration is the uniform acceleration caused by a moving body moving along a straight line. There are three equations that are essential in linear acceleration, depending on parameters like start and terminal velocities, displacements, times, and acceleration.

Given :

linear acceleration a = 1.85 m/s²

angular acceleration α  = 5.23 rad/s²

radius r = a/ α  = [tex]\frac{1.85}{5.23}[/tex] = 0.354 m

diameter  d = 2r = 2 × 0.354 = 0.71 m

diameter of the wheels is  0.71 m.

To know more about angular acceleration, visit:

https://brainly.com/question/29428475

#SPJ1

The magnitude of the net linear acceleration of the car 15.0 seconds later is 5.08 m/s2. This is because acceleration is the rate of change of velocity, and the car's velocity is increasing at a constant rate of 0.600 m/s2.

To calculate the magnitude of the net linear acceleration, we must use the equation a = v2/r, where a is the acceleration, v is the velocity, and r is the radius of the circular track. Since the velocity of the car is increasing at a constant rate of 0.600 m/s2, we can calculate the velocity of the car after 15.0 seconds using the equation v = v0 + at, where v0 is the initial velocity (0 m/s in this case), a is the acceleration (0.600 m/s2), and t is the time (15.0 seconds).
Thus, the velocity of the car after 15.0 seconds is 9.00 m/s. Now, we can plug this velocity, along with the radius of the circular track (47.0 m), into the equation a = v2/r to calculate the magnitude of the net linear acceleration:
a = (9.00 m/s)2/47.0 m = 5.08 m/s2

Therefore, the magnitude of the net linear acceleration of the car 15.0 seconds later is 5.08 m/s2.

For more such questions on Linear acceleration.

https://brainly.com/question/12996537#

#SPJ11

Assuming both rocks are thrown from the same height and with the same initial speed, the rock thrown vertically downward will have a larger velocity upon hitting the ground than the rock thrown vertically upward.

This is because the rock thrown upward will lose speed as it moves against the force of gravity. Eventually, the upward motion will be slowed down until the rock reaches the highest point in its trajectory, where it momentarily stops and changes direction. From that point, the rock will accelerate downward, gaining speed as it falls back to the ground. However, the time spent traveling upward and the time spent traveling downward will not be the same, since the upward portion of the trajectory will be slower due to gravity slowing the rock's ascent. This means that the rock thrown upward will have a lower speed when it hits the ground compared to the rock thrown downward.

On the other hand, the rock thrown downward will experience the force of gravity pulling it towards the ground, causing it to accelerate and gain speed as it falls. Since it is initially moving downward, it will not slow down until it hits the ground, meaning that it will have a higher velocity upon impact than the rock thrown upward.

Learn more about force of gravity here: https://brainly.com/question/2537310.

#SPJ11

(a) To find the energy stored in a magnetic field inside a solenoid, we can use the formula: E = (1/2) * L * I^2, where L is the inductance of the solenoid, and I is the current passing through it. Since the solenoid is air-filled, we can approximate its inductance using the formula: L = (mu * N^2 * A^2) / l

where mu is the permeability of free space, N is the number of turns, A is the cross-sectional area, and l is the length of the solenoid. Substituting the given values, we get L = 0.019 H. Assuming the current passing through the solenoid is negligible, we can calculate the energy stored as: E = (1/2) * L * I^2 = (1/2) * 0.019 * 0^2 = 0 J.

Therefore, the energy stored in the magnetic field is approximately 29 J.

(b) the total energy stored in the earth's magnetic field in the first 10 km above its surface, we can use the formula: E = (1/2) * V * B^2 * mu, where V is the volume, B is the magnetic field, and mu is the permeability of free space. We can approximate the volume of the region as a cylinder with a radius of 6400 km (the radius of the earth) and a height of 10 km.

Substituting the given values, we get E = (1/2) * pi * (6400 + 10)^2 * 10 * (0.5 x 10^-4)^2 * 4pi10^-7 = 5.1 x 10^15 J. Therefore, the total energy stored in the earth's magnetic field in the first 10 km above its surface is approximately 5.1 x 10^15 J.

For more details about inductance click here:

https://brainly.com/question/18575018#
#SPJ11

The magnitude of the electric field at point P which has coordinates (1, 0, 2) m is E = √((-6)² + 0² + 12²) V/m= √180 V/m= 6√5 V/m.

Over a certain region of space, the electric potential is (3x² - 4y² - 12z) V. Find the expressions for the x, y, and z components of the electric field over this region. For a uniform electric field in a given region, the electric potential over that region is related to the electric field through the relation

E = -∇V,

Here ∇ is the nabla operator in Cartesian coordinates.

So, for the given electric potential (3x² - 4y² - 12z) V, the electric field components are given by:

Ex = -dV/dx = -6x V/m

Ey = -dV/dy = 8y V/m

Ez = -dV/dz = 12 V/m

Therefore, the expressions for the x, y, and z components of the electric field over this region are Ex = -6x V/m, Ey = 8y V/m, and Ez = 12 V/m, respectively. The magnitude of the field at point P (1, 0, 2) m can be calculated using the expression for the magnitude of the electric field given by

E = √(Ex² + Ey² + Ez²).

Substituting the given coordinates of point P, we get

Ex = -6(1) V/m = -6 V/m

Ey = 8(0) V/m = 0 V

Ez = 12 V/m

Thus, the magnitude of the electric field at point P is 6√5 V/m.

You can learn more about the electric field at: brainly.com/question/8971780

#SPJ11

The apparent weight of a 70 kg astronaut 2600 km from the center of the earth's moon in a space vehicle moving at constant velocity is zero.

Apparent weight is the force that an object seems to be under when it is on a different acceleration than its actual acceleration. On the moon's surface, the force of gravity is approximately one-sixth of Earth's gravitational force.

As a result, the gravitational force exerted by the moon on the 70 kg astronaut will be lower than the force exerted by the Earth. In the case of the problem given, the space vehicle is traveling at a constant velocity. This implies that the space vehicle's acceleration is zero.

The gravitational pull of the Earth on the astronaut is balanced by the astronaut's centripetal force. As a result, the apparent weight of the astronaut is zero. The apparent weight of a body at rest or moving uniformly in a straight line is zero because the gravitational force acting on it is compensated by the centrifugal force acting on it.

Therefore, the Magnitude of the apparent weight of a 70 kg astronaut 2600 km from the center of the earth's moon in a space vehicle moving at constant velocity is zero.

To know more about apparent weight click here:

https://brainly.com/question/14323035

#SPJ11

Answer : A 1000 kg truck moving at 30 mph has a greater magnitude of linear momentum than a 500 kg car moving at 60 mph, due to the larger mass of the truck and the lower velocity of the truck.

The magnitude of linear momentum for an object is equal to the product of its mass and velocity. Therefore, a 1000 kg truck moving at 30 mph has a linear momentum of 30,000 kg-m/s, while a 500 kg car moving at 60 mph has a linear momentum of 30,000 kg-m/s as well. As the magnitudes of linear momentum for both the truck and car are equal, the truck has a greater linear momentum than the car.

This is because the truck has a larger mass than the car and is moving at a lower velocity. In other words, the higher mass of the truck counteracts its lower velocity, resulting in an overall greater linear momentum. This can be illustrated with the equation p = mv, where p is linear momentum, m is mass, and v is velocity.

Know more about linear momentum here:

https://brainly.com/question/27988315

#SPJ11

Depending on the formulation, gasoline's energy content can vary, but a standard approximation states that one liter of gasoline has around 34 megajoules (MJ) of energy in it.

A liter of gasoline has 31,536,000 joules of energy, which helps to put joules in perspective. A kilowatt-hour has a joule value of 3,600,000. Hence, the energy contained in a liter of gasoline is 8.76 kW/hr,

Let's find out how many kilometers a car can travel on a single tank of gasoline now. The distance driven here is 145 kilometers of distance in 10 litres. So, in 10 litres = 145 km distance covered. That is, in one litre of petrol a car travels a total distance of 14.5 km.

To know more about energy visit:-

brainly.com/question/1932868

#SPJ9

The longest wavelength of the light required to cause photoelectric effect is 349 nm (in nm units).

A photoelectric effect occurs when light falls on a metal surface, causing electrons to be emitted from the metal surface. It's a phenomenon that demonstrates the particle-like nature of light, which is made up of photons, as well as the wave-like nature of light.

Einstein first proposed the idea of the photoelectric effect, which eventually helped him win the Nobel Prize in Physics in 1921.Photoelectric Effect’s Formula

The photoelectric effect's formula is as follows:

Kinetic Energy = Energy of Photon - Work Function

KE = hf - Φ

For this question, we have work function, and we will use it to find the longest wavelength.

The formula of work function is given as Φ= hf0

Where f0 is the threshold frequency (frequency of the incoming light, below which the photoelectric effect does not occur).h = Planck’s constant = 6.626 x 10^-34 J s = 4.136 x 10^-15 eV s

The longest wavelength of the light required to cause photoelectric effect is given asλ = c / f

Here, λ is the wavelength of the incoming light, c is the speed of light, and f is the frequency of the incoming light.

We have to solve the work function equation to find the threshold frequency.

The formula is given asf0 = Φ/h

Substituting the values, we get:f0 = 3.56 eV / 4.136 x 10^-15 eV s = 8.60 x 10^14 Hz

To find the longest wavelength, we use the following formula:

λmax = c / f0 = (3 x 10^8 m/s) / (8.60 x 10^14 Hz) = 3.49 x 10^-7 m = 349 nm

For more question on photoelectric effect click on

https://brainly.com/question/1408276

#SPJ11