in which region are the temperatures and pressures at which it's possible to change the phase of x by raising or lowering the temperature?

The television commercial loudness increases by 10 decibels.

The decibel (dB) scale is a logarithmic measure of sound intensity. The intensity of a sound is measured in watts per square meter and the decibel scale is a way to express the relative loudness of a sound, compared to a reference level.

A 10 dB increase in intensity is a 10-fold increase in sound power. This means that a sound with an intensity of 10 watts per square meter is 10 times louder than a sound with an intensity of 1 watt per square meter.

Learn more about Intensity of sound here:

https://brainly.com/question/17062836

#SPJ1

To calculate the acceleration of a 330000-kg jumbo jet just before takeoff when the thrust on the aircraft is 160000 N, we must use Newton's second law of motion. This states that the net force on an object is equal to the product of its mass and acceleration, or F=ma.

Thus, we can rearrange the equation to solve for acceleration, a = F/m. In this case, a = 160000 N/330000 kg = 0.485 m/s2. This means that the jumbo jet will accelerate at 0.485 m/s2 just before takeoff.

To explain further, when an object experiences a force, it will accelerate. The acceleration is determined by the size of the force, the mass of the object, and the direction of the force. In the case of the jumbo jet, the force is provided by the thrust of its engines, and the mass of the object is 330000 kg.

As the thrust is 160000 N, the acceleration of the jumbo jet will be 0.485 m/s2. This is the acceleration that the jumbo jet will experience just before takeoff.

To know more about acceleration refer here:

https://brainly.com/question/30660316#

#SPJ11

Answer:

Explanation:

The irreversible thermodynamic processes are:

The conversion of work to heat by friction

The free expansion of a gas

The slow and adiabatic expansion of a gas is a reversible process, while the spontaneous flow of heat from a hot body to a cooler body is a natural, irreversible process, but it is not a thermodynamic process per se.

The phenomenon in which an object appears to be different when viewed from different angles is known as a lenticular image. Lenticular printing is the process of producing these images.

Lenticular printing is a method of producing a lenticular image, which is a printed image that shifts as the viewing angle changes. Lenticular printing is a method of generating a composite image by interlacing two or more images using a lenticular lens.

A lenticular image is a picture that appears to alter when viewed from different angles. It is formed by placing a sheet of tiny cylindrical lenses or "lenticules" over a photo that has been divided into a number of frames. The frames are interlaced, resulting in a composite image that alters when viewed from different angles.

The lenticular function as lenses, refracting light at various angles and allowing each eye to see a distinct image. To generate the lenticular image effect, the interlaced images must be magnified and printed onto a lenticular lens. The result is a plastic sheet that appears to display a different image depending on the angle of the viewer's gaze.

To know more about lenticulars image:

https://brainly.com/question/8590716

#SPJ11

If the cell phone battery starts out with no charge and is charged at a constant rate of 900.0 mA, it will take roughly 5,680 seconds or 94.7 minutes to fully charge.

Electricity consumption for phone chargers is typically 5 watts (W) or less. While some faster chargers can use up to 20 W, the majority of standard chargers are closer to the 5–10 W range. Typically, phone chargers connect to a 120-volt outlet and draw one to two amps.

We can apply the following formula to resolve this issue:

time = (charge / current)

charge = 1.420 Ah x 3,600 C/Ah

= 5,112 C

The charging current is then changed from milliamperes (mA) to amperes (A):

current = 900.0 mA / 1,000 = 0.9 A

We can now enter the values into the formula as follows:

time = (charge / current)

= (5,112 C / 0.9 A)

= 5,680 seconds.

To know more about charge visit:-

https://brainly.com/question/14713274

#SPJ1

The acceleration on a body that approaches the Earth and comes within 6 Earth radii of the Earth's surface is known as the "gravitational acceleration."

This is caused by the gravitational pull of the Earth, which increases as the body approaches the Earth's surface. The acceleration is given by the equation a = GM/r², where G is the gravitational constant, M is the mass of the Earth, and r is the distance from the center of the Earth. For a body that comes within 6 Earth radii of the Earth's surface, the acceleration would be equal to GM/36, where G is the gravitational constant and M is the mass of the Earth. This acceleration can be used to calculate the velocity of the body and its trajectory around the Earth.

For more questions on gravitational acceleration

https://brainly.com/question/14374981

#SPJ11

The headline "Enlightenment ideas of freedom, equality, and justice for all" represents the idea of the Enlightenment that human beings are rational, capable of determining right from wrong, and deserving of rights and freedoms, such as freedom of speech, freedom of religion, and equality before the law.

These ideas were a major factor in the shift away from absolute monarchies, and towards governments of the people, by the people, and for the people. The Enlightenment period also saw the development of democracy and of the rule of law, where the government is subject to a set of laws, rather than relying on the whims of the ruler. Enlightenment thinkers sought to empower the individual, giving people the freedom to think and act as they pleased, rather than relying on the decisions of rulers.

For such more questions on Enlightenment idea :

brainly.com/question/11185091

#SPJ11

The capacitance of two metal plates separated by a 0.20-mm-thick is approximately 0.25 pF  and the maximum potential difference between the plates is 8.4 kV.

a. The capacitance of two metal plates separated by a 0.20-mm-thick piece of Teflon is approximately 0.25 pF (picofarad).

b. The maximum potential difference between the two metal plates is determined by the permittivity of the dielectric material, which in this case is Teflon.

The permittivity of Teflon is about 2.1 and the capacitance of the plates is 0.25 pF, so the maximum potential difference between the plates can be calculated using the equation:

Vmax = (permittivity * Capacitance) / Area.

Therefore, the maximum potential difference between the plates is 8.4 kV.

For more such questions on capacitance , Visit:

https://brainly.com/question/13578522

#SPJ11

a..... 1.04 x 10⁻⁴ Vi

b.... 9500 V

A) Determine the capacitance (to the nearest 10 μF).

First, we should identify the formula that we will use to solve the problem.

The formula that relates to capacitance is:

C = 2E / V². Where C is the capacitance in farads, E is the energy stored in joules, and V is the voltage across the capacitor in volts.

Converting the energy to joules, we have: E = 250J.

Now we know that the voltage needs to drop to half of its initial value in 10 ms. We can use the following formula to calculate the capacitance: C = R x t / ln(Vi / Vf) where R is the resistance in ohms, t is the time in seconds, Vi is the initial voltage, and Vf is the final voltage, which is half of the initial voltage.

B) Plugging in the given values, we get:

C = 48 x 0.01 / ln(Vi / (Vi / 2))Simplifying and solving for capacitance, we get:

C = 1.04 x 10⁻⁴ ViNow we can use the energy formula to solve for Vi:Vi = √(2E / C)

Plugging in the given values, we get:Vi = √(2 x 250 / 1.04 x 10⁻⁴)Simplifying and solving for Vi, we get:Vi = 9469 V

Therefore, the capacitance that meets these specifications is 100 μF and the initial capacitor voltage that meets these specifications is 9500 V, to the nearest 100 V.

Learn more about capacitance

brainly.com/question/28445252

#SPJ11

Thana explains that when the charge is zero, the motion of the particle in the simulation is a straight line with a constant velocity.

The direction of the velocity depends on the initial conditions and the force acting on the particle. If there are no other forces acting on the particle, it will continue to move in a straight line with a constant velocity until it encounters another force or object. This is an example of Newton's First Law of Motion, which states that an object at rest will stay at rest and an object in motion will stay in motion with a constant velocity unless acted upon by an external force. If there is a force acting on the particle, it will change direction or speed up or slow down. This is an example of Newton's Second Law of Motion, which states that the force acting on an object is equal to its mass times its acceleration. The direction of the force is in the same direction as the acceleration. When the charge is zero, the particle does not experience any force, so it moves in a straight line with a constant velocity. This is a simple example of how particles can be modeled using physics simulations.

For more such questions on Physics simulations.

https://brainly.com/question/28522691#

#SPJ11

A point closer to the center of the hard drive will have a lower linear acceleration than a point farther from the center. This is due to the fact that linear acceleration is inversely proportional to the radius of rotation. The acceleration is greatest at the outer edges and decreases toward the center.

Linear acceleration is the rate of change of the velocity of an object that moves in a straight line. It is also referred to as the object's increase in speed or decrease in speed. The same concept applies when it comes to hard drives.

It is pertinent to understand that linear acceleration decreases when the radius of the disk decreases, which means that the closer the point is to the center, the lower the linear acceleration would be. This is why the outermost tracks have higher transfer rates and are utilized more for storing data on hard drives.

Read more about acceleration :

https://brainly.com/question/460763

#SPJ11

If the moon enters its waxing crescent phase tonight, then you will see the First Quarter lunar phase in approximately two weeks.

What is the lunar phase?

The Moon is in a specific position during a lunar phase. During the lunar phase cycle, it passes through four primary phases: the new moon, the first quarter, the full moon, and the last quarter. In the new moon phase, the Moon is between the Sun and Earth, and the side of the Moon visible to us is dark.

In contrast, in the full moon phase, the Moon is on the opposite side of the Earth from the Sun, and the side visible to us is entirely illuminated. The first quarter moon is half illuminated and half in shadow, with the illuminated portion appearing as a semi-circle.

The last quarter moon is also half illuminated and half in shadow, but the illuminated portion appears in the opposite direction from the first quarter moon. If the moon enters its waxing crescent phase tonight, you will see the first quarter lunar phase in approximately two weeks. This phase is also known as a half moon, and it occurs when the moon is one-quarter of the way through its orbit around the Earth.

During the first quarter, the illuminated portion of the moon increases each day, until it reaches the full moon phase.

Learn more about phases of the moon here:


https://brainly.com/question/2285324#

#SPJ11

To find the speed of the planet in a perfectly circular orbit around the star, we can use the equation v = sqrt(Gm2 / r). Plugging in the given values, we get v = 1843.3 m/s. Therefore, the planet must have a speed of approximately 1843.3 m/s.

The height h will stay the same when a new block of mass m is used and makes an elastic collision.

Thus, the correct answer is to stay the same.

An elastic collision is a type of collision in which the total kinetic energy of two or more bodies involved in the collision is conserved. In this collision, the colliding bodies return to their initial state before the collision. That is, the total momentum and kinetic energy are conserved.

As a result, the initial and final energies of the system remain the same, implying that the height of the rod will stay the same as before. So, the height h will stay the same.

For more information about elastic collision refers to the link: https://brainly.com/question/2356330

#SPJ11

Iron that is not magnetic will be drawn to a bar magnet. An atom is like a current loop, if it is not observed than it is a magnet.

A piece of iron, which has magnetic qualities, aligns into two poles when placed in the magnetic field of a bar magnet.

If the north pole reports the side in front of it, it is the north pole, and if the south pole reports the south pole, it is the south pole. A piece of iron, which has magnetic qualities, aligns into two poles when placed in the magnetic field of a bar magnet.

Charges that are in motion within an atom produce electricity. The atoms can act as an equivalent current loop thanks to their rotational orbits. Iron is nevertheless drawn to magnetic fields despite their being no current.

To know more about magnetism, visit,

https://brainly.com/question/12740727

#SPJ4

The given statement " A series circuit is a current divider and a parallel circuit is a voltage divider circuit " is True

In a series circuit, the electric current is the same through each component, and the total current is equal to the sum of the currents through each component. Therefore, the current is divided among the components.

In a parallel circuit, the potential voltage across each component is the same, and the total voltage is equal to the sum of the voltages across each component. Therefore, the voltage is divided among the components.

Know more about electric current here:

https://brainly.com/question/2264542

#SPJ11

It is a linear expansion, when a rod undergoes a change in temperature and there is a change in its length.

The length that a rod changes to as a result of a temperature change relies on the rod's initial length, the rate of temperature change, and the material's coefficient of linear expansion. The formula for linear expansion is:

ΔL = αL₀ΔT

Where ΔL is the change in length of the object, is the coefficient for linear expansion of the material in question, and L₀ is the initial length of the object.

Volumetric expansion refers to change in one dimension (volume), whereas linear expansion refers to change in one dimension (length) (volumetric expansion). The area thermal expansion coefficient connects a material's area changes to temperature changes.

To know more about linear expansion, refer:

https://brainly.com/question/19495810

#SPJ4

Complete question is:

A rod undergoes a change in temperature. the change in length is:

A. linear expansion

B. volumetric expansion

The maximum amplitude of the PWM voltage signal applied across the 500-ohm resistor is: Vmax=2*I*R=500*I

The power dissipated by a resistor during one cycle is given by the periodic signal. The PWM voltage signal applied across a 500 Ω resistor is analyzed in this question. The amplitude of the signal is determined below.

Pulse Width Modulation is the PWM. It's a process for varying the pulse width of a square wave, which changes the percentage of time the signal is high to low. The pulse width can be varied to create the desired output signal level. It is frequently utilized in applications where analog signals are required, including control systems, power supplies, and audio systems. The maximum voltage Vm of the PWM voltage signal can be found by calculating the RMS value of the pulse. The root-mean-square value is the square root of the mean of the square of the signal over a given period. If we use a pulse that has a duty cycle of 50%, this formula simplifies to: Vmax=Vm+0.5Vdc where Vdc is the average value of the pulse.

The maximum amplitude can be determined using this formula: Vmax=I*R where I is the current and R is the resistance. The current flowing through the resistor is proportional to the voltage applied to it, and the voltage is proportional to the duty cycle of the PWM signal, which varies from 0 to 1. Thus, the voltage applied to the resistor is proportional to the duty cycle and can be expressed as: V=Vmax*D where D is the duty cycle. Thus, the amplitude of the PWM voltage signal applied across a 500-ohm resistor is: Vmax=2*I*R=500*I. Using this equation, we can determine the maximum amplitude of the PWM voltage signal applied across the 500-ohm resistor.

For more such questions on Pulse Width Modulation.

https://brainly.com/question/29358007#

#SPJ11

A net force of 89.0 n propels a 4.00-kg model rocket. after being launched from the rest,  the rocket will be traveling at: a velocity of 44.5 m/s.

The net force of 89.0 N propels a 4.00-kg model rocket. After being launched from rest, the rocket will have an acceleration of 89.0 N/4.00-kg = 22.25 m/s².

After 2.00 seconds, the rocket's velocity will be 2.00s x 22.25m/s² = 44.5 m/s. Therefore, after 2.00 s, the rocket will be traveling at a velocity of 44.5 m/s.

To calculate this, we first need to know the net force of the rocket. This is equal to the thrust of the rocket (F = ma) multiplied by the mass of the rocket (m = 4.00 kg). We can then use this net force to calculate the acceleration of the rocket, which is equal to  

F/m = 89.0 N/4.00 kg = 22.25 m/s².

Now that we know the acceleration of the rocket, we can use this to calculate the velocity of the rocket after 2.00 s. To do this, we multiply the acceleration by the time, which in this case is 2.00 s. This gives us an initial velocity of 2.00s x 22.25m/s² = 44.5m/s.  

This means that after 2.00 s, the rocket will be traveling at a velocity of 44.5 m/s.

To know more about force refer here:

https://brainly.com/question/13191643#

#SPJ11

The spring is compressed by 0.84 meters.

The potential energy of the block at the starting point is given by,

mgh = 2 x 9.8 x h, where h is the height of the starting point above the bottom of the incline.

Using the given inclination angle of 37 degrees, we can find h as,

h = 4.8 sin(37) = 2.88 m

We can equate the potential energy at the starting point to the energy stored in the compressed spring and the kinetic energy at the bottom of the incline,

mgh = 1/2 kx^2 + 1/2 mv^2

where x is the distance that the spring is compressed, v is the velocity of the block at the bottom of the incline, and k is the spring constant.

Since the block is sliding without friction, we can use conservation of energy to find v as,

mgh = 1/2 mv^2

v^2 = 2gh

v = √(2gh)

Substituting this expression for v in the earlier equation,

mgh = 1/2 kx^2 + 1/2 m(2gh)

2gh = kx^2/m + 2gh

x^2 = 2ghm/k

x = √(2ghm/k)

Substituting the known values,

x = √(2 x 9.8 x 2 x 2.88 / 1000) = 0.84 m

To know more about spring, here

brainly.com/question/14670501

#SPJ4

--The complete question is, A spring is fixed at the bottom end of an incline of inclination 37∘. A small block of mass 2 kg starts slipping down the incline from a point 4.8 m away (along the inclined plane) from the spring. The spring constant is 1000 N/m. How far is the spring compressed?--

The resistance of the copper wire of length 4 m and diameter 0.002 m is 2.25×10⁻² ohms.

Resistance is the opposition to the flow of current in a circuit.

To calculate the reistance of the copper wire, we use the formula below.

Formula:

Where:

From the question,

Given:

Substitute these values into equation 1

Hence, the resistance of the copper wire is 2.25×10⁻² ohms.

Learn more about resistance here: https://brainly.com/question/29635283

#SPJ1

TRUE. When air masses of different densities collide, the less dense air mass is forced to rise through frontal lifting.

In meteorology, a front is a transition area between two air masses of different densities. The atmosphere's temperature, moisture content, and wind direction are all influenced by these air masses. The types of fronts are warm, cold, stationary, and occluded fronts. The front types are determined by the characteristics of the air masses and the direction of their movement. The types of the front are Warm front: When a warm air mass replaces a cold air mass, it is called a warm front. Warm fronts typically move more slowly than cold fronts. Cold front: A cold front happens when a cold air mass replaces a warm air mass. They have steeper pressure gradients than warm fronts, and they travel faster. Rain, thunderstorms, and cold temperatures are all common with this type of front. Stationary front: This occurs when two air masses meet and neither advances. There is a lot of rain along the stationary front. Occluded front: This is a type of front that develops when a cold front overtakes a warm front. When the cool air catches up to the warm air, an occluded front forms. The fronts can cause precipitation to fall.

Learn more about air masses at brainly.com/question/12089291

#SPJ11

The values of the mass m for which the system is underdamped, overdamped and critically damped are m < β/2ω, m > β/2ω, and m = β/2ω, respectively.

To determine the values of mass m for which the system is underdamped, overdamped and critically damped, we need to first understand the underlying mathematics behind damping. Damping is a force that acts on a body to oppose its motion, and the damping coefficient, β, is a measure of how much this damping force opposes the motion.

The damping ratio, ζ, is then a measure of how strong the damping is, in relation to the system's natural frequency. Specifically, ζ = β/2mω ,where m is the mass, and ω is the angular frequency.

Underdamping occurs when ζ is less than one, so when m < β/2ω.

Overdamping occurs when ζ is greater than one, so when m > β/2ω. Critically damping occurs when ζ equals one, so when m = β/2ω.

for such more question on mass

https://brainly.com/question/19385703

#SPJ11

The person must pull downward with a force equal to her weight, which is approximately 760 N in order to raise herself slowly at a constant speed.

When the person pulls downward on the bucket, there are two forces acting on the system: the force of gravity pulling the person and the bucket down, and the force of the person pulling the bucket up. In order for the person to raise herself at a constant speed, the force she exerts on the bucket must be equal and opposite to the force of gravity pulling her down.

The force of gravity on the person and the bucket is equal to their combined weight, which can be calculated as mass times gravitational acceleration (77 kg x 9.81 m/s^2 = 755.37 N). Therefore, the person must exert a force equal to her weight (approximately 760 N) in order to counteract the force of gravity and raise herself at a constant speed.

Thus, to lift herself up slowly and steadily, the person needs to exert a downward force that is equivalent to her weight, which is around 760 Newtons.

To know more about gravitational acceleration click here:

https://brainly.com/question/30429836

#SPJ11

The correct option is B, a liquid needs a container when a solid does not Solids have definite shapes, and liquids fill their containers.

Solids are one of the three fundamental states of matter, along with liquids and gases. In a solid, the molecules are tightly packed together, and the substance maintains a fixed shape and volume. The particles in a solid are held together by strong intermolecular forces, which prevent them from moving freely.

Solids have many properties that distinguish them from other states of matter. For example, they are usually denser and more rigid than liquids and gases. Solids can also be classified into different types based on their internal structure, such as crystalline solids, which have a regular and repeating pattern of atoms, and amorphous solids, which lack a definite long-range structure.

To learn more about Solids visit here:

brainly.com/question/17061172

#SPJ4

Complete Question: -

Which best describes why a liquid needs a container when a solid does not?

A. Solids fill their containers, and liquids have definite shapes.

B. Solids have definite shapes, and liquids fill their containers.

C. Solids particles do not expand to fill their containers, and liquid particles do.

D. Solids particles expand to fill their containers, and liquid particles do not.

To complete the given sentences explaining why the transverse pulse traveling on a rope held by two people reflects in the opposite orientation each time it reaches a person order of the words used is third law, the same, oppose, increase.

When a transverse wave pulse reaches a fixed end of the rope, the displacement of the rope end exerts a force on the object that is keeping the end fixed (in this case, a person). By Newton's third law, the person must exert a force of the same magnitude in oppose direction; otherwise, the end of the rope would not remain stationary but would accelerate in the direction of the force due to the wave disturbance. Because this force acts to increase the force of the incoming wave pulse, it initiates an outgoing wave pulse that is inverted with respect to the incoming wave pulse.

When a transverse pulse traveling on a rope held by two people reaches one of the people, the pulse is reflected in the opposite orientation. This happens because of the interaction between the pulse and the person holding the rope.

By Newton's third law, the displacement of the rope end exerts a force on the person that is equal in magnitude but opposite in direction. If the person did not exert an equal and opposite force, the end of the rope would not remain stationary but would instead accelerate in the direction of the force due to the wave disturbance.

The force exerted by the person opposes the force of the incoming wave pulse, initiating an outgoing wave pulse that is inverted with respect to the incoming wave pulse. This happens due to the conservation of energy and momentum, which are described by Newton's first and second laws. The outgoing pulse has a smaller amplitude than the incoming pulse because some energy is lost in the reflection process.

Learn more about transverse wave pulse:

https://brainly.com/question/15531840

#SPJ11

The change in enthalpy is  0 J/kg if the incompressible substance with a density of 1000 kg/m3 is isothermally compressed from 100 to 1000 kpa. Thus, option b is correct.

The given data is as follows:

The density of substance = 1000 kg/m3

In-compression pressure = 100 to 1000 kph

The given substance is incompressible. So its specific volume stays constant during the process. The work done is Zero.

Assuming that the process is Isothermal, the temperature remains steady.

The change in enthalpy is calculated by using the formula:

ΔH = m × C × ΔT

The density of mass is calculated by using the formula,

m = V × ρ = 1 m3 × 1000 kg/m3

m = 1000 kg

Change in enthalpy is calculated as:

ΔH = m × C × ΔT

ΔH = 1000 kg × 0 J/(kg·K) × 0 K

ΔH = 0 J/kg

Therefore we can conclude that the change in enthalpy is  0 J/kg.

To learn more about enthalpy

https://brainly.com/question/24170335

#SPJ4

The complete question is-

an incompressible substance with a density of 1000 kg/m3 is isothermally compressed from 100 to 1000 kph. determine the change in enthalpy. multiple choice questions.

a.900 kj/kg

b. 0 kj/kg

c.10 kj/kg

d.0.9 kj/kg

The region where most long period comets come from is called the Oort Cloud and it is estimated that it contains up to 2 trillion comets.

The region where most long period comets originate is known as the Oort Cloud. The Oort Cloud is a vast spherical region surrounding the Sun located roughly halfway between the orbits of Neptune and Proxima Centauri. It is estimated to contain up to two trillion icy objects, which are leftovers from the formation of the solar system. Long period comets, which take longer than 200 years to orbit the Sun, originate from the Oort Cloud and make their way towards the inner solar system. They are usually only visible when they come close enough to the Sun to be warmed and shed dust and gas, which form the visible tail of the comet. As they come closer to the Sun, the gravitational attraction of the planets often deflects their orbits and causes them to return to the Oort Cloud for millions of years before repeating the cycle.

For more questions related to comets.

https://brainly.com/question/12443607

#SPJ11

The amount of work required to move the same object the same distance but in 10 years will be the same as before is 1 Joule.

It is known that Work = Force x Distance. So, if it takes 1 Joule of work to move an object a distance of 1 meter with a force of 1 Newton in 10 seconds, we can find the force applied on the object.

The formula for force is:

F = m x a, where m is mass and a is acceleration

F = ma1 N = 1 kg x a

Thus, a = 1 m/s².

Now, we have:

F = 1 N, a = 1 m/s² and d = 1 m.

Putting all values in the formula for work done, we have:

W = F x d

W = 1 N x 1 m

W = 1 J

Thus, the work done to move the object is 1 Joule.

Now, if the object moves the same distance but in 10 years, it would make no difference to the work done. This is because work is calculated using force and distance only, and time does not matter here. Therefore, we can expect the same amount of work required to move the object the same distance.

Learn more about work to move at https://brainly.com/question/25573309

#SPJ11

The gravitational force between two objects is 300 N and the mass of one object is 20.0 kg, while the other object is 30 kg, we have to calculate the distance between the objects the distance is  3.67 m.

The formula for calculating gravitational force between two objects is given by F = G × m₁ × m₂ / r²

where, F = gravitational force between two objects, m₁ = mass of object 1, m₂ = mass of object 2, r = distance between the objects, G = gravitational constant G = 6.67 × 10⁻¹¹ N·m²/kg².

Now, we can use the above formula to calculate the distance between the objects. F = 300 N, m₁ = 20.0 kg, m₂ = 30 kg, G = 6.67 × 10⁻¹¹N·m²/kg². We have to find

r = ?, F = Gm₁m₂/ r²

r = 6.67 × 10⁻¹¹ × 20 × 30/ 300

r = 3.67m

Therefore, the distance between the objects is 3.67 meters.

Read more about force here:

https://brainly.com/question/12785175

#SPJ11