Answer:
increase the length of the handle from the bolt, the torque will increase even if you have the same force
Explanation:
It allows them to apply more torque to the bolt. Torque is the turning or twisting force that causes rotation, in this case, it's applied to the bolt in an effort to loosen it. By lengthening the handle of the wrench, the mechanic is able to leverage more of their body weight and strength behind the wrench, increasing the torque they are able to apply to the bolt.
When a bolt is very tight, it can be difficult to turn it with a standard wrench. The increased torque provided by the longer handle allows the mechanic to apply more force to the bolt, which can help to loosen it. This can be particularly useful in situations where the bolt is corroded, rusted, or otherwise stuck due to a buildup of debris or other factors.
a -ion (negative ion, one with extra negative charge )
A simple pendulum has a period of 3 seconds . If the value of ‘g’ is taken as 9.98 ms-2 calculate the length of the pendulum.
Answer: The length of the pendulum is approximately 2.495 meters.
Explanation:
The period of a simple pendulum is the time it takes for the pendulum to swing back and forth through one full oscillation. The period of a simple pendulum is related to the length of the pendulum and the acceleration due to gravity (g) by the formula:
Period = 2 * pi * sqrt(length / g)
In this case, you are given that the period of the pendulum is 3 seconds and the value of g is 9.98 ms-2. You can use these values to solve for the length of the pendulum using the formula above.
Substituting in the values given, you get:
3 = 2 * pi * sqrt(length / 9.98)
Solving for length, you get:
length = (3 / (2 * pi))^2 * 9.98
= 0.5^2 * 9.98
= 0.25 * 9.98
= 2.495
Therefore, the length of the pendulum is approximately 2.495 meters.
The figure shows a graph of the output from an AC voltage source.
What is the maximum voltage Vmax of the source?
What is the average voltage Vavg of the source?
What is the root-mean-square voltage Vrms of the source?
From the graph,
Vmax = 3V
Vavg = 2*Vmax/π = 2*3/π = 1.91 V
Vrms = Vmax/√2 = 3/√2 = 2.121 V
Note: The graph that has been considered for theses calculation, is uploaded as an attachment along with the answer.
The sine wave can achieve a maximum value known as VMax for both negative and positive directions. It is VMax for a positive cycle and (-)VMax for a negative cycle.
The average of the instantaneous voltages selected at correctly spaced intervals during the half - cycles of an AC sinusoidal (or other periodic) waveform is the average voltage. The average value is a representation of the area beneath the AC wave form as a function of time.
A sinusoidal origin of electromotive force is described by its root-mean-square (rms) voltage (Vrms), denoted by Vmax/√2.
To know more about the Voltage calculation here:
https://brainly.com/question/891089#
#SPJ4
can some one help me with my last question please i really need help
Answer: yeah for sure but post the picture
Explanation:
Lol
Write down whether quantity of potential kinetic and total energy
Potential energy is the power that a thing possesses as a result of where it is in relation to other objects.
What is Potential energy?The earth can pull you down through the force of gravity while doing work in the process, being at the top of a stairwell gives you more potential energy than standing at the bottom.
Two magnets have more potential energy when they are held apart than when they are near to one another. They will migrate near each other and begin working if you let them go.
The force acting on the two objects affects the potential energy formula. P.E. = mgh, where m is the mass in kilograms and g is the acceleration due to gravity, is the formula for gravitational force.
Therefore, Potential energy is the power that a thing possesses as a result of where it is in relation to other objects.
To learn more about Potential energy, refer to the link:
https://brainly.com/question/24284560?
#SPJ1
Freight trains can produce only relatively small acceleration and decelerations. a. What is the final velocity (in m/s) of a freight train that accelerates at a rate of 0.050 m/s2 for 8.0 min, starting with an initial velocity of 3.0 m/s
The final velocity of the freight train is 27 m/s that accelerates at a rate of 0.050 m/s2 for 8.0 min, starting with an initial velocity of 3.0 m/s.
Information given:
Acceleration is 0.050 m/s²
Time is 8.0 min
Initial velocity is 3.0 m/s
We apply the resulting equations for rectilinear motion at constant acceleration to this problem.
a = (v - u)/t
where the,
a is acceleration
u and v are the initial and final velocities, respectively
s is the distance
t is the time
Substituting the values in the equation:
The solution is as follows:
a = (v - v₀)/t
0.050 m/s² = (v - 3 m/s)/(8 min * 60 s/1 min)
Time: 480 sec
Solving for v,
24=v-3
v=27 m/s
Learn more about acceleration:
brainly.com/question/28743430
#SPJ4
The current in a ________
Answer here
circuit is the same at every point?
Answer:
Series.
Explanation:
Current is the same in each device since there is only a single pathway for the charge to flow.
A focus mirror sculpture was opened in Rockefeller Centre in New York City in 2006. Standing three storeys tall and weighing 23 tonnes, its concave side faced the Rockefeller Centre and its convex side faced 5th Avenue.
A. What is the nature of the image of 5th Avenue?
B. Which property of concave mirror is utilised for using them as shaving mirrors?
C. A taxi on 5th Ave is located 38 metres from the convex side of this culture and its image is 1/5 the size of the taxi. Determine the focal length of the mirror.
D. Estimate the image size of the 270 metre tall Rockefeller Centre if it is located an estimated distance of 100 metres from the concave mirrors surface of focal length 10 metre.
A. The nature of the image of 5th Avenue in the mirror sculpture is that it is a virtual, upright, and smaller image. This is because the concave mirror is used to reflect light outwards, creating a virtual image that cannot be projected onto a screen.
B. The property of concave mirrors that is utilized for using them as shaving mirrors is their ability to form a smaller, magnified image. This is because concave mirrors have a negative focal length, which causes light rays to diverge and form a smaller image that is closer to the mirror.
C. To determine the focal length of the mirror, we can use the formula 1/f = 1/u + 1/v, where f is the focal length, u is the object distance (38 meters), and v is the image distance (unknown). We know that the image size is 1/5 the size of the object, so we can set v = -5u (since the image is virtual and inverted). Substituting these values into the formula and solving for f, we get f = -(5u^2)/4 = -(5(38^2))/4 = -4725/4 = -1181.25 meters.
D. To estimate the image size of the 270 meter tall Rockefeller Centre, we can use the formula: h' = -h * (u/f) where h' is the image height, h is the object height (270 meters), u is the object distance (100 meters) and f is the focal length (10 meters). Substituting these values in the formula, h' = -270 * (100/10) = -2700 meters. This means the image of the Rockefeller Centre would be 2700 meters tall, which is not possible because it's taller than the building itself. This is an indication that the image is not real and is a virtual image.
What is the difference between flat mirrors and curved mirrors?Unlike plane mirrors, spherical mirrors form images that are different in size from the size of the object. While the convex mirror forms images that are always smaller than the object, the concave mirror forms images of different sizes, depending on the position in which the object is placed on its axis.
Learn more about convex mirror in brainly.com/question/11627506
#SPJ1
What are the steps and structures involved in the process of cellular respiration?
Answer:
Cellular respiration is a metabolic pathway that breaks down glucose and produces ATP. The stages of cellular respiration include glycolysis, pyruvate oxidation, the citric acid or Krebs cycle, and oxidative phosphorylation.
Explanation:
Answer:
Cellular respiration takes in food and uses it to create ATP, a chemical which the cell uses for energy. Usually, this process uses oxygen, and is called aerobic respiration. It has four stages known as glycolysis, Link reaction, the Krebs cycle, and the electron transport chain
hope this helps
have a good day :)
Explanation:
Two long parallel conductors carries I1 and I2 in opposite directions. Determine the magnetic field between the wires
Answer:
B1 = μ_o•I1/2πr
Explanation:
According to the right hand rule, we can say that the magnetic field at the second wire due to the current being carried in first wire is given by;
B1 = μ_o•I1/2πr
Where;
r is distance that separates the two wires
μ_o is a constant known as permeability of free space
I1 is current in wire 1
How do you find torque with force and distance?
Torque = force x distance from point of rotation
Torque is a measure of the turning effect of an applied force about a specific point or axis. It is calculated by multiplying the force applied to an object by the distance from the point of rotation to the point where the force is applied. The greater the force or the longer the distance from the point of rotation, the greater the torque. The unit of torque is typically Newton-meters (N·m) in the International System of Units (SI) or pound-feet (lb·ft) in the imperial system. Torque is essential in various fields such as physics, mechanics, engineering and robotics.
To know more about Torque click below:
https://brainly.com/question/6855614#
#SPJ4
Describe the properties of oceanic crust
Answer:
Not including a sedimentary cover of variable thickness and composition, the oceanic crust consists of three layers: (1) a relatively thin uppermost volcanic layer of basaltic lavas known as mid-ocean ridge basalts (MORB) erupted on the seafloor; (2) a thicker layer of more coarsely crystalline, intrusive basaltic
An artificial satellite is moving in a circular orbit of radius 24,600 km. Calculate its speed if it takes 12hours to revolve around the earth.
Answer:
the speed of the satellite is 12,880.53 km/h
Explanation:
Given;
radius of the circular orbit, r = 24,600 km
time taken to revolve around Earth, t = 12 hours
The circumference of the satellite is calculated as;
L = 2πr
L = 2π x 24,600 km
L = 49,200π km
L = 154,566.36 km
The speed of the satellite;
v = L/t
v = 154,566.36 / 12
v = 12,880.53 km/h
Therefore, the speed of the satellite is 12,880.53 km/h
a force of 15 N is used to push a box along the floor a distance of 3 meters. find the amount of work done
Answer:
The amount of work done is 45 J.
Explanation:
We know that the force applied is 15N. The amount of displacement experienced by the box is 3 metres along the floor.
Thus, F= 15N
D= 3 metres
The formula for calculating work done is W= F×D
Thus, W=15×3
W=45J
Thus, the amount of work done is 45J.
How much force is needed to accelerate a 63 kg skier at 6 m/s2?
Answer:
378 N
Explanation:
F = ma = (63 kg)(6 m/s²) = 378 N
A skier weighing 63 kg needs 189N of force to accelerate at 6 m/s. The magnitude of the force required to accelerate the sled is 91 newtons.
What is the necessary force to accelerate?An object's acceleration is equal to the net force acting on it divided by its mass, or a = F m, according to Newton's second law of motion. When the object's mass and the net force it is subjected to are known, this acceleration equation can be used to determine its acceleration.
By the second law of Newton, F = ma Add the following numbers:
F=189N F=63kg(2ms 2)
Which two formulas are used to determine acceleration?Formula for acceleration: there are three equations for acceleration:
a = (v_f - v_i) / t;a equals 2 / t2 (d - v_i t)a = F / m ;To learn more about Newton's second law here:
https://brainly.com/question/13447525
#SPJ1
Which organism would most likely have new gene combinations?
Answer:
a hamster resulting from sexual reproduction
Escriba una oracion empleada de dos adjetivos de significado opuesto unidos por la exprecion y a la ves
Answer:
El castigo de Juan fue justo y a la vez injusto.
Explanation:
Adjetivos opuestos: justo - injusto
La oración significa que el que castigo era merecido, sin embargo, puede ser algo exagerado por lo tanto algo injusto. Describiendo la situación con adjetivos con significado opuesto al mismo tiempo, mediante un conector de simultaneidad que es y a la vez.
A block is resting on an slope. (Figure 3) Which of the following forces act on the block? Check all that apply. O weight O static friction O normal force O kinetic friction O force of push
The correct option is A, B, and C. A block resting on a slope is Weight, static friction, and Normal force.
Static friction is a force that continues an item at relaxation. Static friction definition can be written as: The friction skilled while individuals try to move a desk-bound object on a surface, without surely triggering any relative movement between the frame and the surface on which it's miles.
Static friction is a form of friction force that acts on a body when there's no relative motion between the object and the surface. So, it can act even if the frame is in motion however there should be no relative motion.
A pressure acting on an item is said to be a static force if it no longer exchanges the scale, function, or route of that precise object. The pressure implemented to a structure acts as a load to that precise structure, that is why static force is likewise called a static load.
To learn more about Static friction visit here:
brainly.com/question/13000653
#SPJ4
Complete Question:
A block is resting on a slope. (Figure 3) Which of the following forces act on the block?
Check all that apply.
A). Weight
B). Static friction
C). Normal force
D). Kinetic friction
E). Force of push
Two small objects carry the same amount of charge, and the magnitude of the electric force exerted by one object on the other is 0.10 N when they are held 30 mm apart. If the force magnitude increases when the objects are released and free to move, are the objects of the same charge or opposite charge?
The objects must be of opposite charge because the electric force of attraction between them increases when they are released and free to move.
This means that the electric force must be a repulsive force that pushes the objects away from each other. Opposite charges attract and as charges repel, the objects must be of opposite charge for the electric force to increase when the objects are released and free to move.
Therefore when two small objects carry the same amount of charge, the magnitude of the electric force exerted by one object on the other is 0.10 N when they are held 30 mm apart. If the force magnitude increases when the objects are released and free to move, then we can say that they are opposite charges.
Learn more about charge:
https://brainly.com/question/25923373
#SPJ4
a ball is thrown vertically upwards. After resistance is negligible. What is the variation with tiem fo t of the kinetic energy E_k of hte ball
The variation with time of the kinetic energy E_k of the ball is that it decreases. This is because gravity is acting against the ball and slowing it down, so the kinetic energy is decreasing as the ball slows down.
When the ball is released, the initial kinetic energy, E_k, is given by the equation: E_k = mgh, where m is the mass of the ball, g is the gravitational acceleration, and h is the initial height of the ball. As the ball rises, its height increases, and the potential energy, U, increases. However, this increase in potential energy is at the expense of kinetic energy, so the kinetic energy decreases as the ball rises.
When the ball reaches its maximum height, its kinetic energy is zero as it is at rest. As the ball then begins to fall, its potential energy decreases, and its kinetic energy increases. This is because the ball is falling under the action of gravity, and thus its kinetic energy increases as it accelerates downwards. Overall, the kinetic energy of the ball decreases as it rises and increases as it falls.
This is due to the conservation of energy, which states that the total energy of a system remains constant. As the potential energy increases, the kinetic energy decreases, and vice versa.
To know more about kinetic energy refer to the link brainly.com/question/26472013
#SPJ4
Taylor's car broke down and he exerted a force of 8,000 newtons trying to push it before giving up and calling the tow truck. How much work did he accomplish
He accomplished no job. When Taylor's car broke down, he attempted to push it with 8,000 newtons of force before giving up and calling a tow truck.
The amount that indicates how many times a machine multiplies a force is known as what?The mechanical advantage is how many times a machine can multiply the force of the effort. The mechanical advantage of the machine increases when the effort force is exerted across a bigger distance.
Please describe force multiplier machines and provide two instances.Force multipliers are tools that lessen the force required to move an object. Force multipliers come in handy when lifting heavy objects or performing other actions that call for a lot of force.
To know more about force visit:-
https://brainly.com/question/13191643
#SPJ4
The human ear canal is about 2. 8 cm long and can be regarded as a tube open at one end and closed at the eardrum. What is the frequency around which we would expect hearing to be best when the speed of sound in air is 344. 5 m/s? (hint: find the fundamental frequency for the ear canal. )
The human ear canal is closed at one end. Thus, the fundamental frequency of the given ear canal is 3044.64Hz 3044.64 Hz .
Calculation and Explanation:Under air conduction (AC) excitation, the mean resonance frequency of the human middle ear is estimated to be between 0.8 and 1.2 kHz. The typical resonance frequency under bone conduction (BC) excitation, according to research, is higher, at 1.5–2 kHz.
It is a tube with an open end (the concha section) and a closed end (the tympanic membrane), which responds to a quarter-wave by behaving as a resonator. The resonance frequency is described by the equation F=v/4L, where "v" stands for the speed of sound and "L" for the length of the EAC.
The EAR formula should be used: EAR = (1+ i/n)n - 1. I = Stated interest rate, etc.
To learn more about fundamental frequency visit:
brainly.com/question/9424813
#SPJ4
A high diver wants to make sure that she does not move any faster than 32 m/s when she enters the water from a dive. If she leaves the diving board from rest, what is the maximum height the diving board can be above the water (in meters) so that she does not go any faster than 32 m/s
The maximum height the diving board can be above the water is 52.5m, so that she does not go any faster than 32 m/s when she enters the water.
How do you determine the maximum height ?To determine the maximum height the diving board can be above the water, we can use the equation of motion for a freely falling object:
v^2 = u^2 + 2as
where
v = final velocity (32 m/s)
u = initial velocity (0 m/s)
a = acceleration due to gravity (-9.8 m/s^2)
s = distance fallen (height of diving board above water)
We can rearrange the equation to find the distance fallen (s)
s = v^2/(-2a) - u^2/2a
substituting the values
s = 32^2/(-2*(-9.8)) = 32^2/19.6 = (1024/19.6) = 52.5 m
To know more about acceleration visit:
brainly.com/question/980919
#SPJ4
Margy is trying to improve her cardio endurance by performing an exercise in which she alternates walking and running 100.0 m each. If Margy is walking at 1.4 m/s and accelerates at 0.20 m/s2 during one of the running portions, what is her final velocity at the end of the 100.0 m
She moves at 6.5 m/s as her final speed after running 100 meters.
Acceleration or velocity, according to m/s 2?The velocity change of an object per unit of time is known as acceleration. Amounts of acceleration are measured in meters per second squared (m/s2), the SI unit of acceleration. For instance, due to Earth's gravity, a falling object accelerates at a rate of 9.8 m/s2.
A straight-line motion issue looks something like this. These formulas are used to determine the final velocity:
s = Vo*t + (1/2)*a*at2, and Vf = Vo + at
Where:
Vf = = final speed =?
1.4 m/s is the initial velocity, and 0.20 m/s is the acceleration.
100m displacement in 2 seconds.
the first equation is changed by:
100 = 1.4t + (1/2)*0.2*t^2\st = 25.388s
Vf = 1.4 + 0.2 can be used as a replacement in the second equation.
Vf = 6.5m/s
To know more about cardio exercise visit:-
https://brainly.com/question/1311324
#SPJ4
A student gathered two boxes of the same size made of different materials: glass and clear plastic. She placed them on a windowsill in the sun for an hour, and then measured the temperature of the air in each box. What is the temperature of the air in this experiment
According to the given statement The temperature of the air in this experiment is dependent variable.
What do you mean by a material?Material refers to a thing that something else is made out of. Material can also refer to cloth or can be used to describe something that is made of matter and exists in the physical world. Material has many other senses as a noun and an adjective.
What is an example of a material?A material is any substance that an object is made from. Glass, chalk, paper, wax, water, air, clay and plastic are all different materials. All materials are made up of matter.
To know more about material visit:
brainly.com/question/9176437
#SPJ4
A coin placed 0.30 m away from the center of a rotating, horizontal turntable just begins to slip when its translational speed is 0.50 m/s. What is the coefficient of static friction between the coin and the turntable
According to the given statement The coefficient of static friction was found to be about 0.0850.
What is static friction ?Static friction is a force that prevents an item from moving. The friction encountered when persons attempt to move a stationary object on a surface without actually causing any relative motion between the body and the surface on which it is located.
The graph below depicts the turntable's constant maximum speed and the centripetal acceleration of the coin.
(a) The centripetal acceleration is caused by static friction.
(b) Using the diagram below,
mai^=fi^+nj^+mg(−j^)
Fy=0nmg, thus n=mg, and Fr=mrv2=f=n=mg
Then, \sμ=rgv²=(30.0cm)(980cm/s2)(50.0cm/s)²
=0.0850
To learn more about Static friction follow the given link:
brainly.com/question/13000653
#SPJ4
The complete question is -
A coin placed 30.0cm from the center of a rotating, horizontal turntable slips when its speed is 50.0cm/s. (a) What force causes the centripetal acceleration when the coin is stationary relative to the turntable? (b) What is the coefficient of static friction between coin and turntable?
The Jendrassik maneuver is sometimes used when a subject needs to be distracted, and usually results in a larger reflex test response. Was this true for you? Explain what happened
he JM will heighten (exaggerate) lower limb tendon reflexes by countering some of the normal descending inhibition the brain sends to the reflex arc.
What happens during the Jendrassik maneuver?A medical technique called the Jendrassik manoeuvre involves the patient clenching their teeth, flexing both sets of fingers into a hook-like shape, and interlocking those sets of fingers. The patellar reflex is then induced by striking the tendon below the patient's knee with a reflex hammer.
When the technique is not being used, the reflex outcome of the same movement is compared to the induced reaction. When a patient is focused on the technique, a bigger reflex reaction is frequently seen: "Afferent activity brought on by such muscle tension may activate a weak or seemingly absent reflex.
This is the actual justification for the procedure, not that it is intended to divert the patient's attention, a common misperception that persists to this day." This result
To be learn more about procedure refer to:
https://brainly.com/question/27176982?referrer=searchResults
#SPJ1
Salt dissolves in water to form saltwater. Is this considered a chemical change or a physical change
Salt dissolves in water to form saltwater. This kind of change is regarded as a chemical change.
A physical change is a kind of change in which only the physical properties of matter change. In a physical change, neither the composition nor the chemical nature of matter is changed.
A chemical change involves a chemical process that results in the production of new substances. When you dissolve salt in water the sodium chloride dissociates in Na+ and Cl- ions which can be written in the form of a chemical reaction as,
NaCl → Na+(aq) + Cl-(aq)
Thus, dissolving salt in water is an example of a chemical change.
To know more about chemical change:
https://brainly.com/question/2496486
#SPJ4
convert-73°c to kelvin scale
Answer:
200 K
Explanation:
0 °C = 273 K
-73°C = 273 K - 73 K = 200 K
Spring constant problem. What is the formula for k in terms of the period T and the mass?
A. K= 4pi^2m/T^2
B. K= 4*pi^2/mT^2
C. K= 2*pi*m/T
The formula for k in terms of the period T and the mass m in spring constant problem is k = 4π²m/T². The formula applies to a spring-mass system.
What is a spring-mass system?A spring-mass system is a system where a mass of object is attached at the free end of the spring. The system will perform a simple harmonic motion where the oscillations occur periodically. The period of any moving object in that motion can be counted as follows
T = 2π√(m/k)
Where
T = period (s)m = mass of object (kg) k = spring constant (N/m)Find the formula for the spring constant k in terms of T and m!
We use the formula above to find k.
T = 2π√(m/k)
√(m/k) = T/2π
m/k = (T/2π)²
m/k = T²/4π²
k = 4π²m/T²
Hence, the formula for the spring constant in the spring-mass system is k = 4π²m/T². The answer is A.
Learn more about spring mass system here:
brainly.com/question/9434528
#SPJ4