The speed of the cart is 4.0 m/s.
step by step explanation:
Force F is 10-N,
Distance d is 8.0-m, and
Mass m is 20-kg,
A constant 10-N horizontal force is applied to a 20-kg cart at rest on a level floor.
If friction is negligible, then the speed of the cart when it has been pushed 8.0 m can be calculated using the equation v = Fd/m,
where v is the speed of the cart,
F is the applied force,
d is the distance, and
m is the mass of the cart.
so the speed of the cart is v = (10 N × 8.0 m) / 20 kg = 4.0 m/s.
Learn more about Friction here https://brainly.com/question/23161460
#SPJ11
a diffraction grating has 2,210 lines per centimeter. at what angle in degrees will the first-order maximum be for 500 nm wavelength green light?
A diffraction grating has 2,210 lines per centimeter, the angle of the first-order maximum is for 500 nm wavelength green light is: 11.27 degrees
The first-order maximum for 500 nm wavelength green light will occur at an angle of approximately 10.4° when using a diffraction grating with 2,210 lines per centimeter. Diffraction occurs when waves, such as light waves, encounter an obstruction or apertures, and their wave-like behavior is revealed.
The angle of diffraction is related to the wavelength of light and the separation between the lines of the diffraction grating. The angle of the first-order maximum for 500nm wavelength green light at a diffraction grating with 2,210 lines per centimeter can be determined using the equation:
[tex]θ = sin-1(λ/d)[/tex]
where θ is the angle of the first-order maximum, λ is the wavelength of the light, and d is the spacing between the lines of the diffraction grating.
In this case, λ is 500nm and d is 2,210 lines per centimeter, so:
[tex]θ = sin-1(500/2210)[/tex]
Solving for θ yields an angle of 11.27 degrees.
To know more about wavelength refer here:
https://brainly.com/question/12924624#
#SPJ11
how much work do you have to do, in electron volts (ev), to move an electron from infinitely far away to the origin?
To move an electron from infinitely far away to the origin, the amount of work done in electron volts is -13.6 eV.
When an electron is at infinity from the origin, its potential energy is zero. At the origin, the potential energy of the electron is -13.6 eV. This means that if an electron is brought from infinity to the origin, the electron gains -13.6 eV of potential energy.
The amount of work done to move the electron can be calculated by using the formula: W = ΔPE where W is the work done, and ΔPE is the change in potential energy of the electron.
Read more about the topic of potential energy:
https://brainly.com/question/14427111
#SPJ11
Two crates are dropped from the same height in a vacuum. The mass and force of the crates are shown in the diagram. Which of the following statements is supported by the data?
The momentum of both crates will be the same right before they hit the ground.
The normal force will be the same on both crates when they hit the ground.
Both of the crates are accelerating at the same rate.
Both of the crates are falling at a constant speed.
The statement that is supported by the data is that both of the crates are accelerating at the same rate. That is option C.
What is acceleration?Acceleration is defined as the quantity that measures the rate of change of velocity of a moving object.
According to Newton's second law, the force (F) acting on an object is equal to the mass (m) of object times its acceleration (a).
That is F = ma
For the first crate = a = 686/70 = 9.8 m/s²
Fro the second crate = 490/50 = 9.8 m/s²
Therefore, Both of the crates are accelerating at the same rate.
Learn more about mass here:
https://brainly.com/question/28409714
#SPJ1
while a car travels around a circular track at a constant speed, its a) acceleration is non-zero and along the path b) acceleration is non zero and inward toward the center c) acceleration is zero d) acceleration is non-zero and outward from the center
While a car travels around a circular track at a constant speed, its (d) acceleration is non-zero and outward from the center.
When a car travels around a circular track at a constant speed, it is constantly changing direction, and therefore, constantly accelerating. This acceleration is known as centripetal acceleration and is directed towards the center of the circle.
However, according to Newton's third law, every action has an equal and opposite reaction. In this case, the car also experiences an equal and opposite acceleration, known as the centrifugal acceleration, which is directed outward from the center of the circle.
This is the non-zero acceleration experienced by the car, and it acts to counterbalance the centripetal acceleration, keeping the car moving in a circular path.
Therefore, the correct answer is (d) acceleration is non-zero and outward from the center.
For more questions like Acceleration click the link below:
https://brainly.com/question/12550364
#SPJ11
assuming that the magnetic field is uniform between the pole faces and negligible elsewhere, write an expression for the induced emf in the coil.
The induced EMF (electromotive force) in a coil can be calculated using Faraday's Law of Electromagnetic Induction:
EMF = -N(dΦ/dt)
What is the induced emf?In a uniform magnetic field, the flux through the coil can be calculated as:
Φ = BAcos(θ)
where B is the magnitude of the magnetic field, A is the area of the coil, and θ is the angle between the magnetic field and the normal to the coil.
Assuming that the coil is moving perpendicular to the magnetic field (θ = 0), the rate of change of flux is:
dΦ/dt = BA(d/dt)(cos(0))
= 0
Therefore, the induced EMF in the coil is zero.
However, if the coil is moving at an angle to the magnetic field, or if the magnetic field is changing in time, then the induced EMF will not be zero and can be calculated using the above equations.
Learn more about induced emf:https://brainly.com/question/16764848
#SPJ1
the electrostatic engines obtaining the highest degree of conversion of electric power into thrust and having the longest operational lifetime, are also called:
The electrostatic engines obtaining the highest degree of conversion of electric power into thrust and having the longest operational lifetime are also called electrospray thrusters.
Electrospray thrusters are a type of ion thruster that uses electrostatic forces to generate thrust, making them highly efficient and fuel-saving propulsion systems.
Electrospray thrusters use an electrical charge to atomize a propellant and accelerate it in a way that produces thrust. The electrical charge is created by an electrical field that ionizes the propellant and accelerates it out of the engine, resulting in high specific impulse and a long operational lifetime. The propellant is typically a liquid such as xenon, krypton, or argon.
As the propellant is atomized and accelerated, the electrostatic force pushes the ions away from the engine, creating thrust. This type of thruster is typically used in low-power and medium-power applications, such as CubeSats, nanosatellites, and interplanetary missions.
for such more question on electrostatic
https://brainly.com/question/17692887
#SPJ11
A particle executes simple harmonic motion
with an amplitude of 1.67 cm.
At what positive displacement from the
midpoint of its motion does its speed equal
one half of its maximum speed?
Answer in units of cm.
Answer:
0.835cm or 1.145cm
Explanation:
We know that in simple harmonic motion, the speed is at its maximum at the equilibrium point (midpoint) and zero at the amplitude. Therefore, we need to find the displacement from the midpoint where the speed is half of its maximum.
Let's start by finding the maximum velocity. We know that the velocity is given by:
v = Aωcos(ωt)
where A is the amplitude, ω is the angular frequency, and t is the time. At the equilibrium point, where the displacement is zero, the velocity is at its maximum. Therefore:
v_max = Aω
Next, we need to find the velocity when the speed is half of v_max. The speed is given by the absolute value of the velocity:
speed = |v| = Aω|cos(ωt)|
When the speed is half of v_max, we have:
Aω|cos(ωt)| = 0.5v_max
Substituting v_max = Aω, we get:
|cos(ωt)| = 0.5
Since the cosine function oscillates between -1 and 1, we have two possible solutions:
cos(ωt) = 0.5 or cos(ωt) = -0.5
Solving for ωt, we get:
ωt = arccos(0.5) = π/3 or ωt = 2π/3
or
ωt = -arccos(0.5) = -π/3 or ωt = -2π/3
We only need to consider the positive solutions, since displacement is always positive. Therefore:
ωt = π/3 or ωt = 2π/3
The displacement corresponding to these times can be found using the equation for displacement in simple harmonic motion:
x = Acos(ωt)
Substituting ωt = π/3, we get:
x = 1.67cos(π/3) = 0.835 cm
Substituting ωt = 2π/3, we get:
x = 1.67cos(2π/3) = 1.145 cm
Therefore, the particle's speed equals one half of its maximum speed at a positive displacement of either 0.835 cm or 1.145 cm from the midpoint of its motion.
you are standing on a frictionless surface. you throw a heavy rock forward. will you accelerate, and if so, in which direction?
Yes, you will accelerate when you throw a heavy rock forward while standing on a frictionless surface. You will accelerate in the opposite direction to the rock.
The laws of motion developed by Sir Isaac Newton illustrate that an object in motion stays in motion unless an external force acts on it. So, when you toss a heavy rock forward on a frictionless surface, the rock will continue moving in the forward direction until something stops it.
The force that pushes the rock forward is equivalent in magnitude to the force that pushes you backward. Thus, the rock's mass is higher than yours; it will travel further than you, and you will accelerate in the opposite direction to the rock.
Read more about force:
https://brainly.com/question/12785175
#SPJ11
what is the general process by which a large diffuse cloud of gas turns into a star and surrounding planets?
The general process by which a large diffuse cloud of gas turns into a star and surrounding planets are known as: star formation.
The Star Formation process starts with a giant molecular cloud of gas and dust, where the gravitational forces act on the cloud and it collapses under its own gravity. This collapse results in a disc-like structure, which is also known as a protoplanetary disc, and has the potential to form planets.
The center of the disc gets hotter and denser, and eventually, nuclear fusion begins, resulting in the formation of a star. The protoplanetary disc contains a lot of dust and gas, and as the temperature increases, some of the minerals and elements present in the dust start to melt and then solidify, eventually forming small planetesimals, which aggregate to form the larger planets.
As the planets move around in the disc, they can migrate inward and outward, and some can collide and merge with others, thus forming even larger planets.
The remaining gas and dust in the disc are eventually swept up by the planets or blown away by the star's radiation, and the planets settle into stable orbits. This is the general process by which a large diffuse cloud of gas turns into a star and surrounding planets.
To know more about star formationrefer here:
https://brainly.com/question/16118644#
#SPJ11
you throw a 0.80kg snowball at 7.0m/s straight down off a 5.0m tall bridge
The kinetic energy of the snowball just before it hits the ground is 19.6 joules.
How to calculate the kinetic energy?To determine the kinetic energy of the snowball just before it hits the ground, we can use the formula for kinetic energy:
KE = 1/2 m v²
where KE is the kinetic energy, m is the mass of the snowball, and v is the velocity of the snowball just before it hits the ground.
In this case, we know that the mass of the snowball is 0.80 kg and the velocity just before it hits the ground is equal to the initial velocity with which it was thrown (7.0 m/s) since air resistance is assumed to be negligible. Therefore, we can substitute these values into the formula:
KE = 1/2 * 0.80 kg * (7.0 m/s)²
KE = 19.6 J
Therefore, the kinetic energy of the snowball just before it hits the ground is 19.6 joules.
Learn more about energy here:
https://brainly.com/question/1932868
#SPJ9
Correct question is:
You throw a 0.80kg snowball at 7.0m/s straight down off a 5.0m tall bridge then what is the kinetic energy of the snowball just before it hits the ground?
a photon in the rest frame of a star has a wavelength of 780 nm. an observer on earth measures it to be at a wavelength of 768 nm. the star is then:
The star is moving away from the observer. An observer on the Earth measured the wavelength of a photon as 768 nm, while the photon's rest wavelength was 780 nm.
What is the Doppler effect?
According to the Doppler effect, if the wavelength of the wave is measured at different positions, it will shift. In this situation, the observer on the Earth is seeing a shift in the photon's wavelength due to the motion of the star.
To be more specific, when the star moves away from the observer, the observer observes an increase in the wavelength. Therefore, the star is moving away from the observer.
To know more about the Doppler effect:
https://brainly.com/question/5871604
#SPJ11
discuss the shape of the voltage and current waveforms. which appears more sinusoidal and why would you expect it to be that way?
The voltage waveform is more sinusoidal than the current waveform.
This is because the voltage source is assumed to be an ideal source, which means that the voltage is supplied without loss or fluctuation while the current waveform is distorted due to the loads present in the circuit. When a voltage waveform is applied to a circuit with inductance and capacitance, the resulting current waveform will be distorted and will not be sinusoidal. The current waveform is affected by the presence of capacitance and inductance in the circuit, which cause the current to lag behind the voltage. The current waveform becomes more distorted as the load resistance increases.
More on voltage and current waveform: https://brainly.com/question/30054547
#SPJ11
a certain colored light has a frequency of about 7.5 x 1014 hz. what is the wavelength? please show all the steps and all of your work when you upload your final answer.
The wavelength of the colored light is 4.00 x [tex]10^{-7}[/tex] m, or 4.00 x [tex]10^{-4}[/tex] cm.
The wavelength of a certain colored light with a frequency of about 7.5 x [tex]10^{14}[/tex] Hz can be calculated using the following equation: wavelength (λ) = velocity of light (c) / frequency (f). The velocity of light is a constant, so it is equal to 3.00 x [tex]10^{8}[/tex] m/s.
Plugging the given frequency into the equation, we get: λ = 3.00 x [tex]10^{8}[/tex] m/s / 7.5 x [tex]10^{14}[/tex] Hz
Solving for wavelength, we get:
λ = 4.00 x [tex]10^{-7}[/tex] m, or 4.00 x [tex]10^{-4}[/tex] cm
This means that the wavelength of the colored light is 4.00 x [tex]10^{-7}[/tex] m, or 4.00 x [tex]10^{-4}[/tex] cm.
To summarize, the frequency of the colored light is 7.5 x [tex]10^{14}[/tex] Hz, and the corresponding wavelength is 4.00 x [tex]10^{-7}[/tex] m, or 4.00 x [tex]10^{-4}[/tex] cm. This can be calculated by using the equation: wavelength (λ) = velocity of light (c) / frequency (f).
For more such questions on Wavelength.
https://brainly.com/question/20462619#
#SPJ11
what is the resistance of a resistor which produces heat energy at a rate 166.0 w when a current 6.44 a is run through it?
The resistance of a resistor which produces heat energy at a rate of 166.0 W when a current 6.44 A is run through it is: 25.8 ohms
The resistance of a resistor which produces heat energy at a rate of 166.0 W when a current 6.44 A is run through it can be determined using Ohm's Law. According to Ohm's Law, resistance is equal to the voltage divided by the current.
Therefore, in this case, the resistance can be calculated by dividing the voltage of 166.0 W by the current of 6.44 A, which results in a resistance of 25.8 ohms.
This resistance is known as electrical resistance and is measured in ohms. When a current runs through a resistor, it produces heat energy. The amount of heat energy produced is directly proportional to the current and resistance.
Thus, a higher resistance will lead to more heat energy produced. In the example, a current of 6.44 A with a resistance of 25.8 ohms produces 166.0 W of heat energy.
To know more about resistance refer here:
https://brainly.com/question/30799966#
#SPJ11
william herschel tried to locate the center of our galaxy by counting the number of stars in different directions. this did not work because
William Herschel's approach failed due to the fact that some parts of the Milky Way galaxy are denser than others.
This means that the number of stars would be greater in these regions, making it difficult to determine the galaxy's center simply by counting the number of stars in different directions. Herschel's pioneering work, including his discovery of Uranus and his cataloging of hundreds of nebulae, helped pave the way for future astronomers to explore and understand the universe. However, his method for locating the center of the Milky Way was limited by the technology of his time.
In modern times, astronomers have employed a range of techniques to study the galaxy, including measuring the positions and motions of stars, observing the behavior of gas and dust clouds, and using radio and other wavelengths of light to observe the galaxy's structure and composition.
Despite these advances, the center of the Milky Way remains difficult to observe directly due to the presence of dense dust and gas clouds, which block visible light. Nonetheless, astronomers have been able to estimate the location and size of the galaxy's central region through careful analysis of the behavior of stars and other objects orbiting around its center.
To know more about the Milky Way galaxy, refer here:
https://brainly.com/question/2905713#
#SPJ4
describe an experiment you could perform to determine if the mass of a cart has any effect on the amount of energy needed to overcome friction
Answer:
You can perform an experiment to determine if the mass of a cart has any effect on the amount of energy needed to overcome friction. To do this, you will need a cart, something to put on the cart to increase its mass, a surface with a known coefficient of friction, a ruler or measuring tape, and a scale.
First, measure the distance the cart needs to travel over the surface. Then, measure the mass of the cart without any additional weight. Place the cart at the starting point of the measured distance and release it, timing how long it takes to travel the measured distance. Record this time and repeat this step three times.
Next, add a known mass to the cart and repeat the experiment, measuring how long it takes for the cart to travel the measured distance. Record this time and repeat this step three times. Finally, compare the times for the cart with and without the additional weight and note any differences.
This experiment can be used to determine if the mass of a cart has any effect on the amount of energy needed to overcome friction.
Learn more about friction here:
https://brainly.com/question/28356847#
#SPJ11
some materials feel colder than others because...
Well, materials may feel colder than others because they could:
Be stored in cold temperaturesUndergroundNext to the oceanIn the oceanSo those are why they may feel colder
But . . .
Some items could be hotter becuase:
Near hot source ( volcano )Gas pockets ( that realese hot “ temperatures “Those are my reasons why they can either be colder or hotter
suppose i drop a football from a tall building, and 4 seconds elapse before it hits the ground. neglecting air resistance, roughly how fast is the football moving upon impact?
The football is moving at approximately 59 meters/second (212.3 kilometers/hour) upon impact, neglecting air resistance.
The football is moving at approximately 59 meters/second (212.3 kilometers/hour) upon impact, neglecting air resistance. This can be calculated using the equation s=1/2at^2, where 's' is the displacement, 'a' is the acceleration due to gravity (9.8m/s^2), and 't' is the time of the fall (4 seconds). Therefore, the displacement is s=1/2(9.8m/s^2)(4s)^2, which simplifies to s=78.4m.
Since the displacement is known (78.4m), the velocity can be determined using the equation v^2=u^2+2as, where 'v' is the velocity upon impact, 'u' is the initial velocity (0m/s), and 'a' is the acceleration due to gravity (9.8m/s^2). Therefore, the velocity is v=sqrt(2as), which simplifies to v=sqrt(2(9.8m/s^2)(78.4m)), which simplifies to v=59m/s.
This is the speed of the football upon impact, neglecting air resistance. This assumes that the football is dropped from rest, and experiences a uniform acceleration throughout the fall, which is due to gravity. The acceleration due to gravity is a constant 9.8m/s^2, regardless of the speed of the falling object.
For more such questions on Displacement.
https://brainly.com/question/28523671#
#SPJ11
To be able to calculate the energy of a charged capacitorand to understand the concept of energy associated withan electric field.The energy of a charged capacitor is given byU= QV/2, where Q is the charge of the capacitor andV is the potential difference across the capacitor. Theenergy of a charged capacitor can be described as theenergy associated with the electric field created insidethe capacitor.In this problem, you will derive two more formulas for theenergy of a charged capacitor; you will then use aparallel-plate capacitor as a vehicle for obtaining theformula for the energy density associated with an electricfield. It will be useful to recall the definition ofcapacitance, C = Q/V, and the formula for thecapacitance of a parallel-plate capacitor,Co A/d, where A is the area of each of the platesand d is the plate separation. As usual, eo is thepermittivity of free space.
The energy of a charged capacitor can also be written as [tex]U = \frac {CV^2}{2}[/tex] and [tex]U = \frac {Q^2d}{2\epsilon_o A}[/tex].
To derive two more formulas for the energy of a charged capacitor, we start with the definition of capacitance:
C = Q/V
Solving for Q, we get:
Q = CV
Substituting this expression for Q into the original formula for the energy of a charged capacitor, [tex]U = QV/2[/tex], we get:
[tex]U = (CV)V/2[/tex]
[tex]U = CV^2/2[/tex]
This is one of the additional formulas for the energy of a charged capacitor.
Next, we can use the formula for the capacitance of a parallel-plate capacitor to derive the energy density associated with an electric field. The capacitance of a parallel-plate capacitor is given by:
[tex]C = \epsilon _o A/d[/tex]
where εo is the permittivity of free space, A is the area of each plate, and d is the distance between the plates. Solving this equation for the potential difference, V, we get:
[tex]V = Q/C[/tex]
[tex]V = Q/(\epsilon_o A/d)[/tex]
[tex]V = Qd/(\epsilon_o A)[/tex]
Substituting this expression for V into the formula for the energy of a charged capacitor, [tex]U = QV/2[/tex], we get:
[tex]U = \frac {Q^2d}{2\epsilon_o A}[/tex]
This expression gives us the energy associated with the electric field in the capacitor.
Learn more about capacitors:
https://brainly.com/question/21851402
#SPJ11
1. a 0.42-kg object with an initial velocity of 3.40 m/s in the positive x-direction is acted on by a force in the direction of motion. the force does 6.50 j of work. what is the final velocity of the object?(neglect friction)
The final velocity of the object is 8.96 m/s. The result is obtained by using the formula for work which equal to change in kinetical energy.
The force acting on the object is doing work on the object, which is equal to the change in kinetic energy of the object. We can use the following formula to solve for the final velocity.
Change in Kinetic Energy = Work
½m (v₁ - v₀)² = W
We have
m = 0.42 kgv₀ = 3.4 m/sW = 6.5 JFind the final velocity! (v₁ = ?)
Using the equation above, we can solve for the final velocity.
½(0.42) (v₁ - 3.4)² = 6.5
(v₁ - 3.4)² = 30.95
v₁ - 3.4 = √30.95
v₁ = 5.56 + 3.4
v₁ = 8.96
Hence, the final velocity of the object is 8.96 m/s.
Learn more about work done on an object here:
brainly.com/question/30700757
#SPJ11
a block is tied to a post with a cable and rotating with a constant velocity, on a horizontal smooth surface. what is the direction of its acceleration?
When a block is tied to a post with a cable and rotating with a constant velocity, on a horizontal smooth surface, the direction of its acceleration is towards the center of rotation.
Acceleration is a vector quantity that represents a change in velocity in terms of magnitude and direction. When an object changes direction, it is accelerating, and its direction of acceleration is perpendicular to its direction of motion. When an object rotates with a constant velocity, its speed remains constant, but its direction changes continuously. As a result, it is continuously accelerating towards the center of rotation, as in the case of a block tied to a post with a cable rotating on a horizontal smooth surface.
Learn more about acceleration at https://brainly.com/question/460763
#SPJ11
two guys who weight the same are holding onto a massless pole while standing on horizontal frictionless ice. 1)if the guy on the left starts to pull on the pole, where do they meet?
If the guy on the left starts to pull on the pole, they will meet in the middle since the pole is massless and the surface is frictionless.
If the two guys are holding onto a massless pole and standing on horizontal frictionless ice, then there is no net external force acting on the system, and the center of mass of the system will remain stationary. When the guy on the left starts to pull on the pole, he exerts a force on the pole to the left. According to Newton's third law, the pole exerts an equal and opposite force on the guy to the right, causing him to move to the right.
The position where they will meet depends on the magnitudes of the forces that the guy on the left exerts on the pole and the distance between the two guys. If we assume that the guys initially hold the pole at its center of mass, then we can use the principle of conservation of momentum to determine where they will meet.
Since the center of mass remains stationary, the initial momentum of the system is zero. After the guy on the left starts pulling, the system gains a net momentum to the left equal to the force that he exerts on the pole multiplied by the time that he pulls. In order to conserve momentum, the guy on the right must move an equal distance to the right.
Learn more about friction:
https://brainly.com/question/24338873
#SPJ11
the photo at right was taken through a specroscope. what color was the pigment extract used to produce this spectrum? what colo(s) did this extract absorb?
Light is a form of energy. All the properties of light can be explained by Considering the Wave length and lespuscutar theory.
The Wave Theory states that waves are how light moves across space. When Visible light is passed through a prim it is split up into seven colours which corresponds to definite wave length. a phenomenon Called dispersion. The study of interaction between matter and electromagnetic radiation is defined as spectroscopy.
A spectrophotometer is a device which detect the percentage transmittance of light radiation. When light of certain intensity and frequency range is passed through the Sample Thus the instrument Compare the intensity of the transmitted light with that of the incident light.
A spectroscope is a device that divides light into its individual wavelengths to produce a spectrum.
Learn more about Light here:
https://brainly.com/question/7439081
#SPJ1
what is the difference between a planetary fly by and a planetary orbit insertion. list more than 7 thing for each. use this link to find the answer https://solarsystem.nasa.gov/basics/chapter16-1. if you make the answer on table it will great thank please it is due today.
The major objective of a flyby spacecraft is to watch and record without getting snared by the planet's gravity, which is why flyby spacecraft should not be mistaken with orbiter spacecraft.
Flyby of the PlanetsAs a result of all the interplanetary navigation and course corrections completed during the mission, the spacecraft is positioned at the exact right spot and time to conduct its encounter observations. Data collection by a flyby spacecraft is not always possible.planets' orbits: A spaceship carrying out an orbiter mission must employ the same extremely precise interplanetary navigation and course correction techniques as those used for flyby missions. In order to enter planetary orbit, this technique positions the spacecraft exactly where it needs to be at the right time. Together with exact positioning and timing, controlled deceleration is also necessary for orbit insertion.For more information on planetary flyby and orbit kindly visit to
https://brainly.com/question/29851728
#SPJ1
on an asteroid that is twice as far as earth is from the sun, the strength of sunlight would be group of answer choices twice as great as on earth half as great as on earth a quarter as great as on earth the same as on earth
On an asteroid that is twice as far as Earth is from the sun, the strength of sunlight would be c. a quarter as great as on Earth.
Sunlight or solar radiation is the main source of energy that drives climate and weather patterns on Earth. The amount of solar radiation reaching Earth varies depending on the distance of the Earth from the Sun.
An asteroid is a small rocky body orbiting the sun. It is too small to be called a planet, and is instead classified as a minor planet, which is a term used for any astronomical object that is neither a planet nor a comet. They are primarily composed of materials that formed the solar nebula, a disk-shaped cloud of gas and dust left over after the formation of the solar system.Therefore, the strength of sunlight on an asteroid that is twice as far as Earth is from the sun would be a quarter as great as on Earth.
Learn more about solar system at:
https://brainly.com/question/9367001
#SPJ11
what is the voltage across the 5 ohm resistor when the switch has been in position a for a long time?
The voltage is V = I × R = 5 ohms.
The voltage across a 5 ohm resistor when the switch has been in position a for a long time is determined by Ohm’s Law.
This law states that the voltage (V) across a resistor is equal to the current (I) through it multiplied by the resistance (R). Therefore, the voltage across the 5 ohm resistor is V = I × R = 5 ohms.
This voltage can also be found by considering the flow of electrons. In a circuit with a battery and a switch, electrons flow from the positive terminal of the battery to the negative terminal.
When the switch is in position a, the 5 ohm resistor is in the path of the electrons and acts as a barrier.
This resistance causes the electrons to slow down and the voltage across the resistor is determined by the amount of this resistance.
The voltage across the 5 ohm resistor when the switch has been in position a for a long time is determined by Ohm’s Law and the amount of resistance the resistor provides. The voltage is V = I × R = 5 ohms.
to know more about voltage refer here:
https://brainly.com/question/29445057#
#SPJ11
a wrench is used to tighten a nut. a 15n perpendicular force is applied 50cm away from the axis of rotation, and moves a distance of 10 cm as it turns. what is the torque applied to the wrench?
The torque applied to the wrench can be calculated using the formula:
torque = force x distance
where force is the perpendicular force applied, and distance is the distance from the axis of rotation at which the force is applied.
So, torque = 15 N x 0.5 m = 7.5 Nm
However, since the force moves a distance of 10 cm as it turns, the work done is:
work = force x distance moved = 15 N x 0.1 m = 1.5 J
This means that some of the energy applied by the force is lost to friction or other factors, and not all of it is converted into torque.
Learn more about torque at: https://brainly.com/question/17512177
#SPJ11
thermionic diodes are the most widely used diodes because of their small size and weight. true false
Thermionic diodes are the most widely used diodes because of their small size and weight, this statement is: false.
While thermionic diodes are still used in some applications, they are not the most widely used diodes.Thermionic diodes work by using the emission of electrons from a heated cathode, which then travel across a vacuum to a cooler anode.
This is also called a vacuum diode. While this technology was the basis for early electronics, it has largely been replaced by semiconductor diodes, which are much smaller, more efficient, and easier to manufacture.
Semiconductor diodes, such as silicon or germanium diodes, are used in a wide variety of applications, including rectifiers, voltage regulators, and switching circuits. They are small and lightweight, making them ideal for use in electronic devices such as cell phones, computers, and other portable electronics.
Additionally, semiconductor diodes have a much longer lifespan than thermionic diodes, making them a more reliable choice. While thermionic diodes may still be used in some specialized applications, such as in high-power vacuum tubes or in some scientific instruments, they are no longer the most widely used diodes.
To know more about electrons refer here:
https://brainly.com/question/1255220#
#SPJ11
If a model showed every object in the solar system, the model would be hard to understand. Scientists often choose to show certain characteristics in a model and leave out others. A characteristic that is left out is called a limitation of the model. Look again at the model where the size of the Sun compared to Earth and the Moon is accurately represented. Then, answer the question below. Which of the following are limitations of this model? Select all that apply.
Answer: There are actually multiple limitations.
Explanation:
Some limitations of this model could be:
The distances between the objects are not accurately represented.
The model does not show the orbits of the planets around the Sun.
The model does not show the relative distances between the planets.
Hope this helps, and have a great day!
what is the magnitude, in volts, of the maximum potential difference between two parallel conducting plates separated by 0.61 cm of air?
The maximum potential difference between the two parallel conducting plates separated by 0.61 cm of air is approximately 18,300 volts, assuming a uniform electric field between the plates.
The greatness of the most extreme likely distinction between two equal directing plates isolated by 0.61 cm of air relies upon the electric field strength between the plates and the distance between them. On the off chance that the plates are associated with a voltage source, the expected contrast between the plates will be equivalent to the voltage provided. Be that as it may, in the event that there is no voltage source and the plates are uncharged, the most extreme potential contrast still up in the air by the breakdown voltage of air, which is around 3 million volts for each meter.
Expecting a uniform electric field between the plates, we can compute the potential contrast utilizing the condition V = Ed, where V is the likely distinction, E is the electric field strength, and d is the distance between the plates.
Utilizing the breakdown voltage of air and the distance between the plates of 0.61 cm (0.0061 m), we can compute the greatest likely distinction as follows:
V = Ed = (3,000,000 V/m) * (0.0061 m) = 18,300 volts
Consequently, the greatest likely contrast between the two equal directing plates isolated by 0.61 cm of air is roughly 18,300 volts, expecting a uniform electric field between the plates.
To learn more about potential difference, refer:
https://brainly.com/question/30258618
#SPJ4