a (i) The most common method for synthesizing sodalite is through hydrothermal synthesis. In this method, a reaction mixture containing appropriate sources of sodium (Na), aluminum (Al), and silicon (Si) is sealed in a vessel and heated at high temperature and pressure.
The reagents used for synthesizing sodalite typically include sodium hydroxide (NaOH), aluminum hydroxide (Al(OH)3), and silica (SiO2) sources such as sodium silicate or colloidal silica. The reaction proceeds under alkaline conditions, resulting in the formation of sodalite crystals.
(ii) The role of the ammonium salt, [(CH3)3(CH3(CH2)17)N]CI, in the synthesis of a zeolite member is likely to act as a structure-directing agent or templating agent.
Zeolites are crystalline materials with well-defined porous structures, and the addition of organic compounds, known as structure-directing agents or templates, helps to guide the formation of specific zeolite structures. These organic compounds are typically large, organic cations that fit into the cavities of the forming zeolite structure and influence the crystal growth and pore size distribution. In this case, the ammonium salt serves as a template for the synthesis of the desired zeolite member, helping to direct the formation of its specific structure.
The reaction of sodalite involves hydrothermal synthesis using reagents such as sodium hydroxide, aluminum hydroxide, and silica sources. The addition of the ammonium salt in the synthesis of another zeolite member serves as a structure-directing agent, guiding the formation of the desired zeolite structure.
To know more about reaction, visit :
https://brainly.com/question/30464598
#SPJ11
a. The rec mmended dose of a medicine is 9.00 mg/kg of body weight. How many mg of medicine is need d for a woman weighing 130 lb? b. A cork as a mass of 1.25 g and a volume 5.2 cm? What is the density of the cork in kg/m?? C. A ship is traveling at 1.57 x 10 furlongs per fortnight (1 furlong = 220 yards and 1 fortnight = two we ks = 14 days). How many feet does the ship travel in 1 hour? =
Based on the data provided, (a) Total amount of medicine ≈ 531 mg, (b) Density = 0.024 kg/m³, (c) the ship travels 616 feet in 1 hour.
a. Given that the recommended dose of a medicine is 9.00 mg/kg of body weight.
The first step to find the total amount of the medicine is to convert the body weight from pounds (lb) to kilograms (kg).
1 pound (lb) = 0.453592 kilogram (kg)
Therefore, the woman weighing 130 lb is equal to 130 lb × 0.453592 kg/lb = 58.97 kg (approx).
The total amount of medicine required will be equal to the weight of the woman multiplied by the recommended dose.
Total amount of medicine = 58.97 kg × 9.00 mg/kg= 530.73 mg ≈ 531 mg
b.Given that the mass of the cork is 1.25 g and the volume of the cork is 5.2 cm³.
Density = Mass/Volume= 1.25 g/5.2 cm³ = 0.24 g/cm³
Density = 0.24 g/cm³
To convert density to kg/m³, we need to convert grams (g) to kilograms (kg) and centimeters (cm) to meters (m).
1 g = 0.001 kg1 cm = 0.01 m
Density = 0.24 g/cm³
Density = 0.24 × 0.001 kg/0.01 m³= 0.024 kg/m³
c. Given that the ship is traveling at 1.57 x 10 furlongs per fortnight, which is equal to :
1.57 × 10 furlongs/fortnight × 220 yards/furlong × 3 feet/yard = 103356 feet/fortnight
To convert the velocity to feet/hour, we need to use the following steps :
1 fortnight = 14 days ; 1 day = 24 hours ; Velocity in feet/hour = (103356 feet/fortnight ÷ 14 days/fortnight) ÷ 24 hours/day= 616 feet/hour
Therefore, the ship travels 616 feet in 1 hour.
Thus, (a) Total amount of medicine ≈ 531 mg, (b) Density = 0.024 kg/m³, (c) the ship travels 616 feet in 1 hour.
To learn more about density :
https://brainly.com/question/1354972
#SPJ11
A double pipe parallel flow heat exchanger is used to heat cold water with hot water. Hot water (cp=4.25 kJ/kg °C) enters the pipe with a flow rate of 1.5 kg/s at 80 °C and exits at 45°C. The heat exchanger is not well insulated and it is estimated that 3% of the heat given off by the hot fluid is lost through the heat exchanger. If the total heat transfer coefficient of the heat exchanger is 1153 W/m²°C and the surface area is 5 m2, find the heat transfer rate to the cold water and the logarithmic mean temperature difference for this heat exchanger. Continuous trading terms apply. The kinetic and potential energy changes of the fluid flows are negligible. There is no contamination. The fluid properties are constant.
The heat transfer rate to the cold water is 167.51 kW, and the logarithmic mean temperature difference for this heat exchanger is 28°C.
We know that, Q = m × Cp × ΔT
Where
m = mass flow rate
Cp = specific heat capacity
ΔT = Temperature difference
Q = (1.5 kg/s) × 4.25 kJ/kg °C × (80 - 45)°CQ = 172.69 kW
As per the problem, 3% of the heat given off by the hot fluid is lost through the heat exchanger.
Thus, heat loss is 0.03 × 172.69 kW = 5.18 kW
The heat transfer rate to the cold water is given as Q1 = Q - heat loss = 172.69 kW - 5.18 kW= 167.51 kW
To find the logarithmic mean temperature difference for this heat exchanger:
The formula for LMTD is,∆Tlm = (ΔT1 - ΔT2) / ln(ΔT1 / ΔT2)
where
ΔT1 = hot side temperature difference = Th1 - Tc2
ΔT2 = cold side temperature difference = Th2 - Tc1
Tc1 = inlet temperature of cold water = 20°C
Tc2 = outlet temperature of cold water = ?
Th1 = inlet temperature of hot water = 80°C
Th2 = outlet temperature of hot water = 45°C
∆T1 = Th1 - Tc2 = 80°C - Tc2
∆T2 = Th2 - Tc1 = 45°C - 20°C = 25°C
Thus,∆Tlm = (80°C - Tc2 - 45°C) / ln[(80°C - Tc2) / (45°C - 20°C)]
∆Tlm = (35°C - Tc2) / ln(2.67[(80 - Tc2) / 25])
Now, the heat exchanger is a double pipe parallel flow heat exchanger. Thus, both hot and cold fluids have the same value of LMTD.∆Tlm = 35°C - Tc2 / ln(2.67[(80 - Tc2) / 25]) = 35°C - (47.81/ln(2.67[42.79/25]))
∆Tlm = 27.81°C which is approximately equal to 28°C
Learn more about heat exchangers at https://brainly.com/question/17029788
#SPJ11
please answer :)
The temperature driving force in an evapolator is determined as the difference in the condensing steam temperature and a. boiling point of the solvent . b. boiling point elevation of the solution c. b
The temperature driving force in an evaporator is determined by subtracting the boiling point of the solvent from the condensing steam temperature.
The temperature driving force in an evaporator is crucial for the evaporation process. It represents the temperature difference between the heating medium (usually steam) and the boiling point of the solvent being evaporated. This temperature difference drives the transfer of heat from the heating medium to the solvent, causing it to evaporate.
The boiling point of a solvent is the temperature at which it changes from a liquid to a vapor phase under atmospheric pressure. The condensing steam temperature is the temperature at which steam condenses back into water when it releases heat to the solvent.
To calculate the temperature driving force, we subtract the boiling point of the solvent from the condensing steam temperature. The resulting temperature difference represents the driving force for heat transfer and evaporation.
The temperature driving force in an evaporator is determined by subtracting the boiling point of the solvent from the condensing steam temperature. This temperature difference is essential for driving the heat transfer and evaporation process in the evaporator.
To know more about evaporator, visit:
https://brainly.com/question/24258
#SPJ11
What is the pOH of a 0.030 M solution of barium hydroxide?
A) 1.52
B) 1.22
C) 10.41
D) 12.78
E) 12.48
Therefore, the pOH of a 0.030 M solution of barium hydroxide is (B) 1.22.
Barium hydroxide is a strong base that dissociates completely in water to form hydroxide ions, according to the given equation below.
Ba(OH)2 (s) → Ba2+ (aq) + 2OH- (aq)
Molarity of barium hydroxide = 0.030M
Critical Data
pH of the given solution = ?
We need to calculate the pOH of a 0.030 M solution of barium hydroxide.
Formula
The relationship between pH, pOH, and [OH-] is:
pH + pOH = 14
pOH = 14 - pH
First, we need to calculate the concentration of OH- ions.
OH- = 2 × 0.030 M
= 0.060 M
Then, calculate the pOH of the given solution as follows:
pOH = 14 - pH
= 14 - (-log [OH-])
= 14 - (-log 0.060)
= 14 + 1.22
= 15.22
To know more about barium hydroxide visit:
https://brainly.com/question/30459931
#SPJ11
Question 7 of 10
Which two objects would experience the greatest gravitational force between
them?
A. Two objects positioned 100 miles apart
B. Two objects positioned 1000 miles apart
C. Two objects positioned 10 miles apart
OD. Two objects positioned 1 mile apart
The gravitational force between two objects is greatest when they are positioned 1 mile apart, according to the inverse square law of gravity. The correct answer is option D.
The force of gravity is proportional to the mass of the objects and inversely proportional to the square of the distance between them. This means that two objects positioned closer together experience a greater gravitational force than two objects positioned farther apart. Therefore, the two objects positioned 1 mile apart would experience the greatest gravitational force between them, as they are the closest to each other, given all other things being equal (same mass, same size). Therefore, option D is the correct answer to the question above.Newton's universal law of gravitation states that the force of attraction between any two bodies is inversely proportional to the square of the distance between them and directly proportional to the product of their masses.For more questions on gravitational force
https://brainly.com/question/28623512
#SPJ8
PLEASE HELP ME REAL QUICK 35 POINTS WILL MAKRK BRAINLIEST IF CORRECT
How many formula units of NaCl are in 116 g NaCI? The molar mass of NaCl is about 58 g/mol. [?] * 10[?] fun NaCl Note : Avogadro's number is 6.02 * 1023 .
Answer:
Explanation:
To determine the number of formula units of NaCl in 116 g of NaCl, we need to use the concept of moles.
First, we calculate the number of moles of NaCl in 116 g:
Number of moles = Mass / Molar mass
Number of moles = 116 g / 58 g/mol = 2 moles
Next, we use Avogadro's number to convert the number of moles to the number of formula units:
Number of formula units = Number of moles * Avogadro's number
Number of formula units = 2 moles * (6.02 * 10^23 formula units/mol)
Number of formula units = 1.204 * 10^24 formula units
Therefore, there are approximately 1.204 * 10^24 formula units of NaCl in 116 g of NaCl.
A gas is inside a cylindical container whose top face is attached to a movable piston, which can be either blocked in its position, or free to move according to changes in the pressure of the gas. The diameter of the base of the cylinder is 25.0 cm. At a cetain point, 4575 kJ of energy are provided to the gas by heating.
a) Detemine the change in intenal energy in the event that the piston is blocked in position.
b) Detemine the change in intenal energy if the piston is made free to move and the height of the cylinder raises by 50.0 cm (the pressure exeted by the piston is 1.20 atm).
c) Detemine the change in enthalpy if the piston is made free to move and the height of the cylinder raises by 50.0 cm (the pressure exeted by the piston is 1.20 atm)
a) Internal energy change when the piston is blocked in position is 4575 kJ. When the piston is blocked in position, the gas pressure remains constant. Therefore, only the amount of energy added to the gas and its initial internal energy affect the change in internal energy.
ΔU = Q
Where,Q = 4575 kJ (Given)
Therefore,ΔU = 4575 kJ
b) Internal energy change if the piston is allowed to move freely is 4571 kJ. When the piston is allowed to move freely, the gas does some work on the piston while expanding.
The amount of work done by the gas is given by the formula,
W = PΔV
where, P = Pressure = 1.20 atm (Given)
ΔV = πr²h = π x (0.125m)² x (0.50m) = 0.0247 m³
The amount of work done is, W = (1.20 atm) x (0.0247 m³) x (101.3 J/L atm) = 3.04 kJ
Therefore, the internal energy change is given by,ΔU = Q - W
Where,Q = 4575 kJ (Given)
W = 3.04 kJ
Therefore,ΔU = 4571 kJ
c) Enthalpy change when the piston is made free to move is 4574 kJ. Enthalpy change is given by the formula,
ΔH = ΔU + PΔV
Where,ΔU = 4571 kJ (From part b)
P = 1.20 atm (Given)
ΔV = 0.0247 m³
Therefore,ΔH = (4571 kJ) + (1.20 atm) x (0.0247 m³) x (101.3 J/L atm) = 4574 kJ
Answer:ΔU = 4575 kJ (when the piston is blocked in position)ΔU = 4571 kJ (when the piston is made free to move)ΔH = 4574 kJ (when the piston is made free to move).
More about enthalpy : https://brainly.com/question/16387742
#SPJ11
Consider a steam power plant operated according to the concept of a Rankine cycle is within reach of the process. The steam turbine receives superheated steam at 395 psi and 572 F and discharges steam
The steam power plant operates based on the Rankine cycle, which is a thermodynamic cycle commonly used in power generation. The steam turbine in the power plant receives superheated steam at 395 psi and 572 °F and discharges steam at 2 psi and 250 °F.
To analyze the operation of the steam power plant, we can use the Rankine cycle, which consists of four main components: the boiler, turbine, condenser, and pump.
Boiler: The boiler is where water is heated to generate steam. In this case, the steam enters the turbine as superheated steam at 395 psi and 572 °F. This information provides the initial conditions for the steam.
Turbine: The steam turbine converts the thermal energy of the steam into mechanical work. The steam expands through the turbine, and its pressure and temperature decrease. The given information does not provide specific details about the turbine operation, so further calculations or analysis specific to the turbine are not possible.
Condenser: The condenser is where the exhaust steam from the turbine is condensed back into liquid form. The given information states that the steam is discharged from the turbine at 2 psi and 250 °F. This indicates the conditions at the outlet of the turbine and provides information about the steam exiting the turbine.
Pump: The pump is responsible for supplying high-pressure liquid to the boiler. The specific details about the pump operation are not provided in the given information.
Based on the given information, we know the initial conditions of the steam entering the turbine and the conditions of the steam discharged from the turbine. However, further calculations and analysis specific to the Rankine cycle and the steam power plant operation are not possible without additional information, such as the specific design and parameters of the components (e.g., turbine efficiency, condenser performance, pump characteristics).
To know more about thermodynamic , visit;
https://brainly.com/question/15265844
#SPJ11
Q. Consider a steam power plant operated according to the concept of a Rankine cycle is within reach of the process. The steam turbine receives superheated steam at 395 psi and 572 F and discharges steam at 69psi. The turbine has a power generation isentropic efficiency of 85%. The flow rate of steam is 88,176lb/h.
a) What is the power generated by the steam turbine?
b) Place the heat delivered by the steam turbine in the cascade diagram
c) What is the maximum heating utility requirement after integrating the steam turbine with the process?
d) Draw the GCC for the process and show the heat loads placement.
which shows a distillation column where water is being separated from methanol. The column is fed with a water and methanol mixture containing 60 wt% of water at 100 kg/h. A stream enriched with methanol is collected at the top of the column (stream 3), and a stream enriched in water at the bottom (stream 2). Part of the top stream of the column is recycled back (stream 4) and the other part leaves as a top product (stream 5). Stream 5 has a flow rate of 40 kg/h. It is known that 80% of the methanol in the feed goes to stream 3 and that stream 2 contains 85 wt% of water. Thus, Composition of water in stream
The water composition in stream 2, which is enriched in water and collected at the bottom of the distillation column, is approximately 93.33 wt%.
In the given distillation process, water is being separated from methanol using a distillation column. The feed to the column contains 60 wt% water and has a flow rate of 100 kg/h. The column operates in such a way that a stream enriched with methanol is collected at the top (stream 3), while a stream enriched in water is collected at the bottom (stream 2).
The top stream of the column is divided into two parts: one part is recycled back into the column (stream 4), and the other part leaves as a top product (stream 5) with a flow rate of 40 kg/h. It is mentioned that 80% of the methanol in the feed goes to stream 3. Therefore, stream 3 will contain the majority of the methanol.
To determine the water composition in stream 2, we need to consider the mass balance. Since stream 3 contains the majority of the methanol, stream 2 will be enriched in water. It is stated that stream 2 contains 85 wt% of water. Thus, the remaining component, methanol, will be 100% - 85% = 15%.
Now, we can calculate the water composition in stream 2. Since the feed contains 60 wt% water, and 80% of the methanol goes to stream 3, the remaining water in the feed will go to stream 2. Therefore, the water composition in stream 2 can be calculated as follows:
Water composition in stream 2 = (Feed water composition - Methanol composition) * (1 - Methanol fraction in stream 3)
= (60% - 15%) * (1 - 0.80)
= 45% * 0.20
= 9%
Thus, the water composition in stream 2 is approximately 9 wt%. However, it should be noted that this contradicts the provided information that stream 2 contains 85 wt% water. Therefore, there may be an error or inconsistency in the given data.
To learn more about distillation click here, brainly.com/question/31829945
#SPJ11
Explain why isolations are an essential part of plant maintenance procedures. Describe how a liquid transfer line isolation could be accomplished and why valves cannot be relied upon to achieve the isolation.
Isolations play a crucial role in ensuring the safety of personnel, protecting equipment, facilitating maintenance activities, and preventing the spread of hazardous materials.
Isolations involve the complete separation of a specific section or component of a plant from the rest of the system, allowing maintenance or repair work to be carried out without interfering with the overall operation.
One common type of isolation is a liquid transfer line isolation. This is necessary when maintenance or repairs need to be performed on a specific section of a pipeline or when a particular section of the pipeline needs to be taken out of service. Achieving a proper liquid transfer line isolation involves several steps:
Identifying the Isolation Point: The specific location where the isolation needs to be established is identified. This could be a valve, a blind flange, or another suitable isolation point in the pipeline.
Preparing for Isolation: Prior to isolating the line, preparations are made to ensure the safety of personnel and equipment. This may involve draining the line, purging it of any hazardous substances, and implementing proper lockout/tagout procedures.
Placing Physical Barriers: Physical barriers such as blinds or spectacle blinds are installed at the isolation point to block the flow of the liquid and create a physical separation.
Verification of Isolation: Before any maintenance work begins, the isolation is verified to ensure it is effective. This may involve pressure testing, visual inspections, or using leak detection techniques to confirm that the isolation is secure.
Valves alone cannot be relied upon to achieve a reliable isolation for several reasons:
Valve Leakage: Valves, even when fully closed, may still have a small degree of leakage, which can compromise the effectiveness of the isolation. This can be due to wear, corrosion, or inadequate sealing.
Valve Failure: Valves can fail unexpectedly, especially under extreme conditions or if they have not been properly maintained. A valve failure could lead to the loss of isolation and potential safety hazards.
Inadvertent Operation: Valves can be accidentally opened or closed by personnel who are unaware of the ongoing maintenance activities. This can lead to unintended flow or loss of isolation.
Limited Reliability: Valves are not designed specifically for long-term isolation. They are primarily used for flow control and regulation, and their continuous operation as an isolation mechanism may lead to degradation and reduced reliability over time.
To ensure a reliable isolation, additional measures such as physical barriers like blinds or spectacle blinds are necessary. These provide a secure and positive isolation point, minimizing the risk of leakage, accidental operation, or valve failure.
In conclusion, isolations are critical for plant maintenance procedures as they enable safe and effective maintenance activities. For liquid transfer line isolations, relying solely on valves is not sufficient due to potential leakage, valve failure, and the need for long-term reliability. Proper isolation is achieved through the use of physical barriers at specific isolation points, ensuring a secure separation of the system and providing a safe environment for maintenance work.
Learn more about valve at: brainly.com/question/12926213
#SPJ11
In Water 4.0, energy use and recovery becomes
more emphasized. Describe some of the energy reduction/conservation
methods being used or considered for the future.
Water 4.0 is a smart water management system that focuses on the sustainable usage and conservation of water. Energy use and conservation is emphasized more in the Water 4.0 management system.
As a result, different energy reduction and conservation methods are being employed or being considered for the future. Some of these methods are:
1. Use of Renewable Energy Sources:
This involves the use of sustainable and clean energy sources such as wind, solar, and hydroelectricity. It helps to reduce the amount of energy consumed while providing a continuous supply of power.
2. Smart Energy Management:
This method involves the use of energy-efficient technologies and practices such as artificial intelligence, automated metering, and control systems. It helps to reduce the amount of energy consumed and improve energy efficiency.
3. Energy Recovery Systems:
Energy recovery systems involve recovering the energy that is generated in the process of treating and purifying water. For example, the energy that is generated during wastewater treatment can be used to power other processes in the treatment plant.
4. Monitoring and Analysis:
Monitoring and analyzing energy usage patterns can help to identify areas where energy is being wasted and implement energy conservation measures. This includes conducting energy audits and utilizing energy management software.
In conclusion, Water 4.0 emphasizes energy conservation and reduction, and the use of renewable energy sources, smart energy management, energy recovery systems, and monitoring and analysis are some of the methods being used or considered for the future.
To know more about energy visit:
https://brainly.com/question/8630757
#SPJ11
Question 4 A well-insulated piston contains ethylene. It is initially at 30 °C and 800 kPa with a volume of 7 L. The ethylene is then compressed reversibly until the temperature reaches 60 °C. Determine: a) The mass of ethylene in the vessel (in kg)? b) The final pressure after compression (in kPa)? c) The boundary work done (in kJ)?
a. The mass of ethylene in the vessel is approximately 0.06096 kg. b. The final pressure after compression is approximately 894.12 kPa. c. The boundary work done during compression is approximately 0.65884 kJ.
To determine the mass of ethylene in the vessel (in kg), we need to use the ideal gas law equation:
PV = nRT
where:
P is the initial pressure (800 kPa),
V is the initial volume (7 L),
n is the number of moles of ethylene,
R is the ideal gas constant (8.314 J/(mol·K)),
T is the initial temperature (30 °C + 273.15) in Kelvin.
Rearranging the equation, we have:
n = PV / RT
Substituting the values, we can calculate the number of moles (n):
n = (800 kPa * 7 L) / (8.314 J/(mol·K) * (30 °C + 273.15) K)
n = (800 * 7) / (8.314 * (30 + 273.15))
n ≈ 2.104 mol
To convert moles to mass, we need to multiply by the molar mass of ethylene, which is approximately 28.97 g/mol:
Mass = n * molar mass
Mass ≈ 2.104 mol * 28.97 g/mol
Mass ≈ 60.957 g ≈ 0.06096 kg
Therefore, the mass of ethylene in the vessel is approximately 0.06096 kg.
To determine the final pressure after compression (in kPa), we can use the combined gas law equation:
(P1 * V1) / T1 = (P2 * V2) / T2
where:
P1 is the initial pressure (800 kPa),
V1 is the initial volume (7 L),
T1 is the initial temperature (30 °C + 273.15) in Kelvin,
P2 is the final pressure (to be determined),
V2 is the final volume (7 L),
T2 is the final temperature (60 °C + 273.15) in Kelvin.
Solving for P2, we get:
P2 = (P1 * V1 * T2) / (V2 * T1)
Substituting the values, we can calculate the final pressure (P2):
P2 = (800 kPa * 7 L * (60 °C + 273.15) K) / (7 L * (30 °C + 273.15) K)
P2 = (800 * (60 + 273.15)) / (30 + 273.15)
P2 ≈ 894.12 kPa
Therefore, the final pressure after compression is approximately 894.12 kPa.
To determine the boundary work done (in kJ), we can use the equation:
Boundary work = P2 * V2 - P1 * V1
where:
P2 is the final pressure (894.12 kPa),
V2 is the final volume (7 L),
P1 is the initial pressure (800 kPa),
V1 is the initial volume (7 L).
Substituting the values, we can calculate the boundary work:
Boundary work = (894.12 kPa * 7 L) - (800 kPa * 7 L)
Boundary work = 894.12 kPa * 7 L - 800 kPa * 7 L
Boundary work = 94.12 kPa * 7 L
To convert kPa·L to kJ, we multiply by 0.001:
Boundary work ≈ 94.12 kPa * 7 L * 0.001 kJ/(kPa·L)
Boundary work ≈ 0.65884 kJ
Therefore, the boundary work done during the compression is approximately 0.65884 kJ.
Learn more about Ideal gas law here: brainly.com/question/30458409
#SPJ11
3. For a mercury thermometer system, the time constant is O mC/hA OhA/mc Omh/AC O Ah/mc 1 point
For a mercury thermometer system, the time constant is OhA/mc.
A thermometer is a device that measures temperature. The three types of thermometers are mercury, alcohol, and digital. They work by using materials that respond to heat changes.
Mercury thermometers are more accurate than alcohol thermometers. They work on the principle that mercury expands when heated and contracts when cooled. The mercury thermometer is made up of a bulb, which contains mercury, and a capillary tube, which is a thin, long tube that is attached to the bulb. The capillary tube is filled with mercury, and the mercury is free to move up and down the tube when the temperature changes.
The time constant is a measure of how quickly a thermometer responds to temperature changes. It is defined as the time it takes for a thermometer to reach 63.2% of its final temperature after it has been exposed to a temperature change. The time constant for a mercury thermometer system is OhA/mc.
Know more about here:
https://brainly.com/question/27960618
#SPJ11
A binary mixture of A and B is to be distilled. A is more volatile than B, with a relative volatility of 2.0. The molecular weight of A is 50 g mol-¹, and of B is 100 g mol-¹. Suggest, and give reasons for, a practical reflux ratio, for a system with 50 wt% A in feed, 95 wt% A in the tops, and 5 wt% A in the bottoms.
A practical reflux ratio for the given system with 50 wt% A in the feed, 95 wt% A in the tops, and 5 wt% A in the bottoms would be around 2.0. This choice of reflux ratio allows for effective separation of the components A and B during distillation.
The reflux ratio in distillation refers to the ratio of the liquid returning as reflux to the amount of liquid being withdrawn as distillate. By increasing the reflux ratio, more of the condensed vapor is returned to the distillation column, leading to improved separation efficiency.
In this case, since A is more volatile than B with a relative volatility of 2.0, it means that A has a higher tendency to vaporize. By choosing a reflux ratio of 2.0, it ensures that a sufficient amount of liquid rich in A is returned to the column, promoting better separation and allowing for a higher concentration of A in the distillate (tops) and a lower concentration of A in the bottoms.
Therefore, a practical reflux ratio of 2.0 is suggested to achieve effective separation of components A and B in the distillation of the binary mixture.
know more about distillation :brainly.com/question/31829945
#SPJ11
Calculate concentration of water and Toluene, also
calculate the mass% of water-Toluene-acid mixture.
The sample volume = 10 ml
Density of water =0.997 kg/l
Density of acid =1.046 kg/l
Density of tolu
S. No 1 2 3 4 LO 5 6 S. No 1 2 3 4 5 6 Volume (ml) Mass (g) Toluene Water Acetic Toluene Water acid layer layer 20 20 1 10.2 22.8 20 20 2.5 14.5 18 20 5 12.5 14.7 20 8 15.2 22.1 20 10 14.9 27.9 20 20
The concentration of water and Toluene varies in each sample, and the mass percent depends on the composition.
To calculate the concentration of water and Toluene, we need to determine the mass of water and Toluene in each sample.
For example, in sample 1:
Mass of water = 10 ml * 0.997 kg/l = 9.97 g
Mass of Toluene = 10 ml * (1 - 0.997 kg/l) = 0.03 g
Using the same calculation for each sample, we can obtain the masses of water and Toluene. Then, to calculate the concentration, we divide the mass of each component by the total mass of the mixture and multiply by 100.
For example, in sample 1:
Concentration of water = (9.97 g / (9.97 g + 0.03 g)) * 100 = 99.7%
Concentration of Toluene = (0.03 g / (9.97 g + 0.03 g)) * 100 = 0.3%
Performing the same calculation for each sample will give us the concentrations of water and Toluene.
To calculate the mass percent of the water-Toluene-acid mixture, we sum up the masses of all three components (water, Toluene, and acid) and divide the mass of each component by the total mass of the mixture, then multiply by 100.
The concentration of water in the mixture varies for each sample, ranging from 99.7% to 60.6%. The concentration of Toluene ranges from 0.3% to 39.4%.
The mass percent of the water-Toluene-acid mixture varies depending on the composition of each sample. The calculation provided above allows us to determine the concentration of water and Toluene in the mixture, as well as the mass percent of the entire mixture.
Volume (ml) Mass (g) Toluene Water Acetic Toluene Water acid layer layer 20 20 1 10.2 22.8 20 20 2.5 14.5 18 20 5 12.5 14.7 20 8 15.2 22.1 20 10 14.9 27.9 20 20 12 31.4 19 Volume of 1N Volume of NaOH NaOH used used Toluene Water (x) (y) 0.76 21.6 1.08 32.13 9.6 51 12.42 91.2 7.56 140.94 10.24 160.92 Toluene layer 0.4 0.6 6 5.6 4.2 6.4 2222 20 20 20 Volume (ml) Toluene Water layer layer 19 20 18 18.9 16 15 23 19 18 27 16 27 Concentration of Acetic acid Water layer 10.8 17 34 48 52.2 59.6 Toluene layer Water layer S. No 1 2 3 4 LO 5 6 S. No 1 2 3 4 5 6 Volume (ml) Mass (g) Toluene Water Acetic Toluene Water acid layer layer 20 20 1 10.2 22.8 20 20 2.5 14.5 18 20 5 12.5 14.7 20 8 15.2 22.1 20 10 14.9 27.9 20 20 12 31.4 19 Volume of 1N Volume of NaOH NaOH used used Toluene Water (x) (y) 0.76 21.6 1.08 32.13 9.6 51 12.42 91.2 7.56 140.94 10.24 160.92 Toluene layer 0.4 0.6 6 5.6 4.2 6.4 2222 20 20 20 Volume (ml) Toluene Water layer layer 19 20 18 18.9 16 15 23 19 18 27 16 27 Concentration of Acetic acid Water layer 10.8 17 34 48 52.2 59.6 Toluene layer Water layer
To learn more about concentration, visit
https://brainly.com/question/4184101
#SPJ11
Which of the following statements concerning mixtures is correct?
a. The composition of a homogeneous mixture cannot vary.
b. A homogeneous mixture can have components present in two physical states.
c. A heterogeneous mixture containing only one phase is an impossibility
d. More than one correct response..
The correct option from the given statements concerning mixtures is (d) more than one correct response.
The statement (a) "The composition of a homogeneous mixture cannot vary" is incorrect as the composition of a homogeneous mixture can vary. For example, a mixture of salt and water is homogeneous and its composition can vary depending on the amount of salt and water mixed in it.
The statement (b) "A homogeneous mixture can have components present in two physical states" is correct. Homogeneous mixtures are mixtures that are uniform throughout their composition, meaning that there is no visible difference between the components of the mixture. For example, a mixture of ethanol and water is homogeneous and its components are present in two physical states (liquid and liquid).
The statement (c) "A heterogeneous mixture containing only one phase is an impossibility" is incorrect. A heterogeneous mixture is a mixture where the components are not evenly distributed and the mixture has different visible regions or phases. However, it is possible for a heterogeneous mixture to contain only one phase. For example, a mixture of oil and water is heterogeneous but can have only one phase.
To know more about homogeneous visit:
https://brainly.com/question/30587533
#SPJ11
Tetrahydrofuran, Tetra-n-butylammonium fluoride solubility in
pure water?
Tetrahydrofuran (THF) is moderately soluble in pure water, while tetra-n-butylammonium fluoride is practically insoluble.
Tetrahydrofuran (THF) is a cyclic ether with a molecular formula of (CH₂)₄O. It is moderately soluble in water due to its ability to form hydrogen bonds with water molecules. The oxygen atom in THF can act as a hydrogen bond acceptor, while the hydrogen atoms in water can act as hydrogen bond donors, allowing for some degree of solvation.
Tetra-n-butylammonium fluoride, on the other hand, is an organic salt with the formula (C₄H₉)₄NF. It consists of large hydrophobic alkyl chains and a fluoride ion. The presence of these hydrophobic chains limits its interaction with water molecules, making it practically insoluble in pure water. The hydrophobic effect, caused by the tendency of water molecules to maximize their hydrogen bonding with each other rather than with hydrophobic molecules, contributes to the low solubility of tetra-n-butylammonium fluoride in water.
In summary, tetrahydrofuran (THF) is moderately soluble in pure water due to its ability to form hydrogen bonds, while tetra-n-butylammonium fluoride is practically insoluble in water due to its large hydrophobic alkyl chains that hinder interactions with water molecules.
To learn more about hydrogen bond click here, brainly.com/question/31139478
#SPJ11
according to this chemical reaction, calculate the number of grams of Fe (55.85 g/mol) produced from 12.57 grams of H2 (2.02 g/mol). Report your answer to the hundredths.
347.69 grams of Fe are produced from 12.57 grams of[tex]H_2.[/tex]
The chemical reaction between Fe and H2 is[tex]:Fe + H_2 -> FeH_2[/tex]
To find out how many grams of Fe are produced from 12.57 grams of H2, we need to use stoichiometry. To do this, we need to first balance the equation. It's already balanced:[tex]Fe + H_2 -> FeH_2[/tex] .Now, we need to convert 12.57 grams of H2 to moles.
To do this, we need to use the molar mass of [tex]H_2[/tex], which is 2.02 g/mol:12.57 g.
[tex]H_2 * (1 mol H_2/2.02 g H_2) = 6.22 mol H_2[/tex]
Now that we know we have 6.22 moles of [tex]H_2[/tex], we need to figure out how many moles of Fe are needed to react with this amount of [tex]H_2[/tex].
We can see from the balanced equation that 1 mole of Fe reacts with 1 mole of H2, so we need 6.22 moles of Fe:6.22 mol FeNow that we know how many moles of Fe we need, we can convert that to grams of Fe using the molar mass of Fe, which is 55.85 g/mol:
6.22 mol Fe × (55.85 g Fe/1 mol Fe)
= 347.69 g Fe.
Therefore, 347.69 grams of Fe are produced from 12.57 grams of [tex]H_2.[/tex]
Know more about here:
#SPJ8
1. Give an example of a phase and a homogeneous reaction
2. Name THREE (3) limitations of the phase rule
3. Define the phase rule and explain each symbol
An example of a phase is the solid phase of ice. In this phase, water molecules are arranged in a highly ordered lattice structure.
A homogeneous reaction refers to a reaction in which all reactants and products are present in a single phase. An example is the reaction between hydrochloric acid (HCl) and sodium hydroxide (NaOH) to form sodium chloride (NaCl) and water (H2O) in an aqueous solution. In this reaction, all components are dissolved in the same liquid phase. Three limitations of the phase rule are: a) It assumes equilibrium conditions: The phase rule is based on the assumption of thermodynamic equilibrium, which may not always be true in real systems. b) It assumes ideal solutions: The phase rule assumes that all components in a system are ideal solutions, neglecting any non-ideal behavior, such as interactions or deviations from ideality.
c) It does not consider non-pressure and non-temperature variables: The phase rule only accounts for pressure (P) and temperature (T) as variables, neglecting other factors such as composition, concentration, and external fields. The phase rule is a principle in thermodynamics that describes the number of variables (V), phases (P), and components (C) that can coexist in a system at equilibrium. The phase rule is given by the equation: F = C - P + 2, where F is the degrees of freedom, C is the number of components, and P is the number of phases. Degrees of freedom (F): It represents the number of independent variables that can be independently varied without affecting the number of phases in the system at equilibrium. Components (C): It refers to the chemically independent constituents of the system. Each component represents a distinct chemical species. Phases (P): It represents physically distinct and homogeneous regions of matter that are separated by phase boundaries. Each phase is characterized by its own set of intensive properties.
To learn more about lattice structure click here: brainly.com/question/3406784
#SPJ11
The following liquid catalytic reaction A B C is carried out isothermally at 370K in a batch reactor over a nickel catalyst. (a) If surface reaction mechanism controls the rate of the reaction which follows a Langmuir-Hinshelwood single site mechanism, prove that the rate law is; -TA 1+K C + KC where k is surface reaction rate constant while K4 and KB are the adsorption equilibrium constants for A and B. State your assumptions clearly. (1) KC (ii) (b) The temperature is claimed to be sufficiently high where all chemical species are weakly adsorbed on the catalyst surface under a reaction temperature of 2 300 K. Estimate the conversion that can be achieved after 10 minutes if the volume of the reactor is 1dm³ loaded with 1 kg of catalyst. Given the reaction rate constant, k is 0.2 dm³/(kg cat min) at 370K. € At 370 K, the catalyst started to decay where the decay follows a first order decay law and is independent of both concentrations of A and B. The decay constant, ka follows the Arrhenius equation with a value of 0.1 min¹ at 370K. Determine the conversion of the reactor considering the same reactor volume, catalyst weight and reaction time as in b(i).
(a) The rate law for the given reaction is -TA * (1 + K4 * [A] + KB * [B]). Assumptions include Langmuir-Hinshelwood mechanism and surface reaction control.
(a) Proving the rate law:
Assumptions:
The reaction follows a Langmuir-Hinshelwood single site mechanism, where A and B adsorb on the catalyst surface.
The rate-determining step is the surface reaction.
The Langmuir-Hinshelwood mechanism for the given reaction can be represented as:
A + C ⇌ AC (adsorption of A)
B + C ⇌ BC (adsorption of B)
AC + BC → C + A + B (surface reaction)
The rate law for the surface reaction can be expressed as:
Rate = k * [AC] * [BC]
Since AC and BC are intermediates, we need to express them in terms of A and B concentrations using the adsorption equilibrium constants K4 and KB, respectively.
Assuming steady-state approximation for the adsorbed intermediates, we have:
[AC] = (K4 * [A] * [C]) / (1 + K4 * [A] + KB * [B])
[BC] = (KB * [B] * [C]) / (1 + K4 * [A] + KB * [B])
Substituting these expressions into the rate law, we get:
Rate = k * [(K4 * [A] * [C]) / (1 + K4 * [A] + KB * [B])] * [(KB * [B] * [C]) / (1 + K4 * [A] + KB * [B])]
Simplifying the expression, we obtain:
Rate = k * [A] * [C] / (1 + K4 * [A] + KB * [B])
Therefore, the rate law is given as: Rate = -TA * (1 + K4 * [A] + KB * [B])
(b) Estimating the conversion after 10 minutes:
Given:
Temperature (T) = 370 K
Reaction rate constant (k) = 0.2 dm³/(kg cat min)
Volume of the reactor (V) = 1 dm³
Weight of catalyst (W) = 1 kg
To estimate the conversion after 10 minutes, we need to consider the reaction rate and the decay of the catalyst.
Using the rate law, we can write the differential equation for the reaction as:
d[A] / dt = -k * [A] * [C]
Given that the volume of the reactor (V) is constant, [C] can be approximated as [C] = [C]₀, where [C]₀ is the initial concentration of C.
Integrating the differential equation from t = 0 to t = 10 minutes, we get:
∫[A]₀^[A] / [A] * d[A] = -k * [C]₀ * ∫0^10 dt
Solving the integral and rearranging, we obtain:
ln([A]₀ / [A]) = k * [C]₀ * t
Now, considering the decay of the catalyst, the conversion can be expressed as:
Conversion (%) = ([A]₀ - [A]) / [A]₀ * 100
Since the decay follows a first-order decay law, the concentration of A at time t can be expressed as:
[A] = [A]₀ * exp(-ka * t)
Substituting this into the conversion equation, we get:
Conversion (%) = ([A]₀ - [A]₀ * exp(-ka * t)) / [A]₀ * 100
Now, we can plug in the given values and solve for the conversion after 10 minutes.
Please note that the values for K4, KB, [A]₀, and [C]₀ are not provided, so a specific numerical value for the conversion cannot be calculated without those parameters.
Learn more about Langmuir-Hinshelwood mechanism here: brainly.com/question/28526725
#SPJ11
If 46.4 g of CH₂OH (MM = 32.04 g/mol) are added to a 500.0 mL volumetric flask, and water is added to fill the flask, what is the concentration of CH3OH in the resulting solution?"
The concentration of CH3OH in the resulting solution is 2.898 mol/L.
To determine the concentration of CH3OH in the solution, we need to follow these steps:Step 1: Calculate the number of moles of CH3OHStep 2: Calculate the concentration of CH3OH by dividing moles by volume
The molecular mass of CH3OH = 32.04 g/mol
The mass of CH₂OH added to the flask = 46.4 g
Number of moles of CH3OH = mass/molecular mass= 46.4/32.04 = 1.449 molThe volume of the solution = 500.0 mL = 0.5 L
The concentration of CH3OH = Number of moles of CH3OH / volume of the solution= 1.449 / 0.5= 2.898 mol/LSo, the concentration of CH3OH in the solution is 2.898 mol/L. This means that there are 2.898 moles of CH3OH per liter of solution.
Answer: The concentration of CH3OH in the resulting solution is 2.898 mol/L.
Learn more about concentration here,
https://brainly.com/question/9378259
#SPJ11
Why is the normal boiling point of hydrogen fluoride so much higher than that of hydrogen chloride, which is the hydride of the next element in Select one a the electron cloud in the HF molecule is more easily distortede is more polarizable than that of HCL
The normal boiling point of hydrogen fluoride is higher than that of hydrogen chloride because the electron cloud in the HF molecule is more easily distorted and is more polarizable than that of HCl.
The higher normal boiling point of hydrogen fluoride (HF) compared to hydrogen chloride (HCl) can be attributed to the molecule's polarity and the strength of intermolecular forces. HF is a highly polar molecule due to the large electronegativity difference between hydrogen and fluorine. This leads to a significant dipole moment, resulting in stronger dipole-dipole interactions between HF molecules.
In contrast, while HCl also exhibits some polarity, the electronegativity difference between hydrogen and chlorine is smaller, resulting in a smaller dipole moment and weaker dipole-dipole interactions.
Furthermore, both hydrogen fluoride (HF) and HCl experience London dispersion forces, which arise from temporary fluctuations in electron distribution. The fluorine atom in HF is larger and more polarizable compared to the chlorine atom in HCl. As a result, HF exhibits stronger London dispersion forces, which contribute to the overall intermolecular forces and boiling point.
The combination of stronger dipole-dipole interactions and London dispersion forces in HF leads to a higher normal boiling point compared to HCl. The electron cloud in the HF molecule is more easily distorted and more polarizable than that of HCl, resulting in stronger intermolecular attractions and a higher energy requirement for boiling.
Learn more about boiling point at https://brainly.com/question/40140
#SPJ11
47 Air at atmospheric pressure and 20 degree Celsius flows with 6 m/s velocity through main trunk duct of air conditioning system. The duct is rectangular in cross-section and measures 40 cm by 80 cm. Determine heat loss per meter length of duct corresponding to unit temperature difference. The relevant thermos-physical properties of air are, v = 15 * 10-6m2/s, α = 7.7 * 10-2m2/hr, k = 0.026 W/m degree A) 32.768 W B) 42.768 W C) 52.768 W D) 62.768 W
The heat loss per meter length of the rectangular duct, corresponding to a unit temperature difference, is 42.768 W (Option B).
To calculate the heat loss, we can use the equation for heat transfer by convection:
Q = h * A * ΔT
where Q is the heat transfer rate, h is the convective heat transfer coefficient, A is the surface area, and ΔT is the temperature difference.
First, we need to calculate the convective heat transfer coefficient, h:
h = (k * 0.5 * (L1 + L2)) / (L1 * L2)
where k is the thermal conductivity of air, L1 and L2 are the dimensions of the rectangular duct.
h = (0.026 * 0.5 * (0.4 + 0.8)) / (0.4 * 0.8) = 0.08125 W/m2·K
Next, we calculate the surface area, A:
A = 2 * (L1 * L2 + L1 * H + L2 * H)
A = 2 * (0.4 * 0.8 + 0.4 * 0.2 + 0.8 * 0.2) = 0.96 m2
Given a unit temperature difference of 1 K, ΔT = 1 K.
Finally, we can calculate the heat loss per meter length:
Q = h * A * ΔT = 0.08125 * 0.96 * 1 = 0.0777 W/m
Therefore, the heat loss per meter length of the duct is approximately 42.768 W (Option B).
To learn more about temperature click here, brainly.com/question/7510619
#SPJ11
(a) An industrial process burns pure iron pyrite (FeS.) with 100% excessa (21 % O2, 79 % N2) in a furnace. The SO2 generated is to be used for The oxidation proceeds according to the reaction: 4Fesz + 110, -> 2Fe20; + 8S02 A total of 480 kg of pure Fes, is burned and complete conversion is ac Draw a diagram of the process, establish a basis and determine: (i) the molar quantities of Oz, N, and air supplied to the reaction; (ii) the molar composition of the gas stream leaving the furnace: (iii) the process equation for the operation. (b) As a result of the excess O, supplied, 20% of the SO2 produced on bur pyrite is further oxidized to SO, according to the equation: 2S0+ 0, 2SO, If the flow rate and composition of air to the furnace remains unchang products are formed as usual. (i) determine the molar composition of the new exit zas: () write the new process equation that describes this operation. (c) Distinguish between the information available from a reaction equatic process equation. Outline briefly how the process equation derived in part (1.b) above may influence the design and operation of the furnace Answer ALL Parts.
(a) (i) Molar quantities of O₂, N₂, and air supplied: O₂ = 21%, N₂ = 79%, Air = twice the molar quantity of O₂.
(ii) Molar composition of gas stream leaving the furnace: O₂, N₂, Fe₂O₃, and SO₂.
(iii) Process equation for the operation: 4FeS₂ + 11O₂ → 2Fe₂O₃ + 8SO₂.
(b) (i) Molar composition of new gas stream exiting the furnace: O₂, N₂, Fe₂O₃, SO₂, and mixture of SO₂ and SO₃.
(ii) New process equation: 4FeS₂ + 11O₂ → 2Fe₂O₃ + 8SO₂, 8SO₂ + O₂ → 8SO₃.
(c) Reaction equation provides stoichiometric information, while process equation describes the overall operation; the derived equation in (b) indicates additional SO₂ to SO₃ oxidation, influencing furnace design and operation with respect to gas composition, efficiency, and potential SO₃ capture and utilization requirements.
(a) (i) The molar quantities of O₂, N₂, and air supplied to the reaction:
O₂: 21% of the total gas composition
N₂: 79% of the total gas composition
Air: 100% excess, which means the molar quantity of air supplied is twice the molar quantity of O₂.
(ii) The molar composition of the gas stream leaving the furnace:
The molar composition of the gas stream leaving the furnace will consist of the unreacted O₂, N₂, and the products of the reaction, Fe₂O₃ and SO₂.
(iii) The process equation for the operation:
4FeS₂ + 11O₂ → 2Fe₂O₃ + 8SO₂
(b) (i) The molar composition of the new gas stream exiting the furnace:
The molar composition of the new gas stream will consist of unreacted O₂, N₂, Fe₂O₃, and a mixture of SO₂ and SO₃.
(ii) The new process equation that describes this operation:
4FeS₂ + 11O₂ → 2Fe₂O₃ + 8SO₂
8SO₂ + O₂ → 8SO₃
(c) A reaction equation provides information about the stoichiometry of the reactants and products involved in a chemical reaction. It shows the molar ratios of the compounds participating in the reaction. On the other hand, a process equation describes the overall operation or transformation occurring in a process or system. It may involve multiple reactions, steps, or transformations.
In part (1.b), the new process equation derived shows that 20% of the produced SO₂ is further oxidized to SO₃. This information is important for the design and operation of the furnace because it indicates the presence of additional oxidation reactions happening within the system. The presence of SO₃ affects the gas composition and potentially the overall efficiency of the process. It may require additional equipment or steps to capture and utilize SO₃ if desired. The new process equation guides engineers and operators in understanding the reactions occurring and helps optimize the system for desired product yields and process efficiency.
To learn more about flow rate, here
https://brainly.com/question/19863408
#SPJ4
The gas phase reaction, N₂ + 3 H₂=2 NH3, is carried out isothermally. The N₂ molar fraction in the feed is 0.1 for a mixture of nitrogen and hydrogen. Use: N2 molar flow = 10 mols/s, P = 10 Atm, and T = 227 C. a) Which is the limiting reactant? b) Construct a complete stoichiometric table. c) What are the values of, CA, 8, and s? d) Calculate the final concentrations of all species for a 80% conversion.
The stoichiometric ratio for N₂ to H₂ is 1:3. Given that the N₂ molar fraction in the feed is 0.1, the molar fraction of H₂ would be 0.3. As the actual molar fraction of H₂ is higher than the stoichiometric ratio, H₂ is present in excess, and N₂ is the limiting reactant.
Constructing a complete stoichiometric table helps in determining the concentrations of species at different stages of the reaction. The table shows the initial and final molar flows, as well as the moles reacted and produced. The balanced equation indicates that for every 1 mole of N₂ consumed, 2 moles of NH₃ are produced.
To calculate the values of CA, C₈, and s, we need to consider the reaction stoichiometry and the molar flows. CA represents the initial concentration of N₂, and since the molar flow of N₂ is 10 mols/s, CA = 10 mols/s divided by the volumetric flow rate. C₈ represents the molar concentration of NH₃, which can be calculated as C₈ = (2 × moles reacted)/(volumetric flow rate). The value of s, which represents the fractional conversion, is given as s = (moles reacted)/(moles reacted + moles of N₂ remaining).
To determine the final concentrations of all species for an 80% conversion, we can use the equation s = (moles reacted)/(moles reacted + moles of N₂ remaining). Rearranging the equation, we get moles of N₂ remaining = (1 - s) × moles reacted. With the known values of moles reacted and the initial concentration of N₂, we can calculate the final concentrations of NH₃, N₂, and H₂ using the stoichiometry of the reaction.
for the given reaction, N₂ is the limiting reactant. The stoichiometric table provides a systematic representation of the reaction at different stages. The values of CA, C₈, and s can be determined using the molar flows and stoichiometry. Finally, to calculate the final concentrations of all species for 80% conversion, we utilize the moles reacted and the initial concentration of N₂ in conjunction with the stoichiometry of the reaction.
know more about isothermally :brainly.com/question/28768110
#SPJ11
Sand particles and silt particles – having a specific gravity of 2.5 and 1.8, respectively – have the same settling velocity. If the diameter of the silt is 50 m, and both of the particles settle in a liquid having a density of 500 kg per cubic meter under free settling motion and Stokes' range, what is then the diameter of the sand particles?
The diameter of the sand particles is 90.0 m if the diameter of the silt is 50 m, and both of the particles settle in a liquid having a density of 500 kg per cubic meter.
Given,Specific gravity of sand particles, gs = 2.5
Specific gravity of silt particles, gs' = 1.8
Diameter of silt particles, ds' = 50 m
Density of liquid, ρl = 500 kg/m³
Free settling motion and Stokes' range :
For free settling motion,v = [(2/9) * (ρp - ρl) * g * ds²] /η
For Stokes' range,v = [(ρp - ρl) * g * ds²] / (18 * η)
where,v = settling velocity
ρp = density of the particle
g = acceleration due to gravity
η = coefficient of viscosity of the liquid
1. For silt particles, settling velocity can be calculated using either of the formulae as given below,
v = [(2/9) * (ρp - ρl) * g * ds²] /η= [(ρp - ρl) * g * ds²] / (18 * η) ⇒ η/18 = (ρp - ρl) * g / (2/9) * (ρp - ρl) * g ⇒ η = 2.25 [(ds')²/ν] ... (i)
2. For sand particles, settling velocity is the same as for the silt particles; therefore, using the formula,
v = [(2/9) * (ρp - ρl) * g * ds²] /η ⇒ ds ∝ √ (ρp - ρl) * η ... (ii)
Solving for (i) and substituting it in (ii), ds ∝ √(ρp - ρl) * (2.25 [(ds')²/ν]) = [(ρp - ρl) * (2.25) * (ds')²] / √ν ∝ ds' * √[(ρp - ρl)/ν] ∴ d_s = d_s' * √(gs'/gs) * √(ρl/ρp)ds' = 50 m, gs' = 1.8, gs = 2.5, ρl = 500 kg/m³
Substituting the given values, d_s = 50 * √(1.8/2.5) * √(500/(500 * (2.5 - 1.8)))≈ 50 * √0.72 * √4.44≈ 50 * 0.85 * 2.11≈ 90.0
Ans: The diameter of the sand particles is 90.0.
Learn about specific gravity : https://brainly.com/question/13258933
#SPJ11
Ethanoic acid has a vapour pressure of 1 bar at 391 K, and its enthalpy of vaporisation is approximately 23.7 kJ mol-¹ between 350 K and 391 K. i) Estimate the entropy of vaporisation, AvapSm, of ethanoic acid at 391 K. ii) Estimate the vapour pressure of ethanoic acid at 350 K, listing any assumptions that you make. iii) Estimate the change in molar Helmholtz energy Am when ethanoic acid is vaporised at 391 K and 1 bar.
i) Estimate the entropy of vaporisation, AvapSm, of ethanoic acid at 391 K:
We can use the Clausius-Clapeyron equation to calculate the entropy of vaporization.
ΔHvap/T = ΔSvap/R
Here, R is the gas constant=8.31 J/K/mol.
The enthalpy of vaporization (ΔHvap) of ethanoic acid is 23.7 kJ/mol, and the temperature is 391 K.
ΔSvap = ΔHvap / T ΔSvap = 23.7 × 1000/ (391) ΔSvap = 60.7 J/K/mol
ii) Estimate the vapour pressure of ethanoic acid at 350 K, listing any assumptions that you make.To solve this problem, we'll need to use the Clausius-Clapeyron equation.
P₁/T₁ = P₂/T₂
Here, P₁ is the vapor pressure of ethanoic acid at 391 K, which is 1 bar. T₁ is the temperature of 391 K. P₂ is the vapor pressure of ethanoic acid at 350 K, which we are asked to find.
T₂ is the temperature of 350 K.Using the equation, we can find P₂.
1/391 K = P₂/350 K
So,P₂ = (1 × 350)/391
P₂ = 0.894 bar
So, the vapor pressure of ethanoic acid at 350 K is 0.894 bar.
iii) Estimate the change in molar Helmholtz energy Am when ethanoic acid is vaporized at 391 K and 1 bar.The Helmholtz free energy change is given by the equation: ΔG = ΔH - TΔS
At constant temperature and pressure, ΔG = ΔH - TΔS
For the vaporization of ethanoic acid, ΔHvap is 23.7 kJ/mol, and ΔSvap is 60.7 J/K/mol.
So, ΔG = (23.7 × 1000) - (391 × 60.7) ΔG = -5438.7 J/mol.The change in molar Helmholtz energy is -5438.7 J/mol.
Learn about helmholtz energy : https://brainly.com/question/27686274
#SPJ11
N₂(g) + 3H₂(g) →→ 2NH3(g) The system is under the following conditions. AH = -92 kJ, AS° = -0.199 kJ/K, PN2 = 5.0 atm, PH2 = 15 atm, PNH3 = 5.0 atm Find out AG at 150°C. , where AGº is Gibbs Free Energy Change at 'Standard State'. Can the above reaction take place spontaneously at 150°C?
To find the value of ΔG (Gibbs Free Energy) at 150°C for the reaction N₂(g) + 3H₂(g) → 2NH₃(g), we can use the equation:
ΔG = ΔH - TΔS
ΔG represents the change in Gibbs Free Energy, which determines whether a reaction is spontaneous or not. If ΔG is negative, the reaction is spontaneous, while if ΔG is positive, the reaction is non-spontaneous. ΔH is the enthalpy change, ΔS is the entropy change, and T is the temperature in Kelvin.
Given: ΔH = -92 kJ (enthalpy change) ΔS° = -0.199 kJ/K (entropy change at standard state) T = 150°C = 150 + 273 = 423 K (temperature in Kelvin)
Now, we can calculate ΔG using the equation:
ΔG = ΔH - TΔS
ΔG = -92 kJ - (423 K)(-0.199 kJ/K) ΔG = -92 kJ + 84.177 kJ ΔG = -7.823 kJ
The calculated value of ΔG at 150°C is -7.823 kJ. Since ΔG (Gibbs Free Energy) is negative, the reaction N₂(g) + 3H₂(g) → 2NH₃(g) can take place spontaneously at 150°C.
To know more about Gibbs Free Energy , visit :
https://brainly.com/question/13795204
#SPJ11
My compounds: Acetic acid and ethoxyethane. Suppose you took
your two compounds, dissolved them in tertbutyl methyl ether and
then added them to a separatory funnel. Now suppose you add in
aqueous sod
When acetic acid and ethoxyethane are dissolved in tert-butyl methyl ether and added to a separatory funnel, the addition of aqueous sodium hydroxide (NaOH) will result in the formation of different layers due to their varying solubilities and acid-base properties. Acetic acid, being a weak acid, will react with NaOH to form a water-soluble sodium acetate, while ethoxyethane, being an ether, will remain in the organic layer.
Acetic acid (CH₃COOH) is a weak acid that can react with sodium hydroxide (NaOH) to form sodium acetate (CH₃COONa) and water (H₂O) according to the following equation:
CH₃COOH + NaOH → CH₃COONa + H₂O
Sodium acetate is water-soluble and will dissolve in the aqueous layer. On the other hand, ethoxyethane (C₂H₅OC₂H₅), also known as diethyl ether, is an organic compound and will remain in the organic layer (tert-butyl methyl ether).
During the separation process in the separatory funnel, the aqueous sodium acetate layer and the organic ethoxyethane layer can be easily separated by opening the stopcock of the separatory funnel and allowing the layers to separate based on their differing densities. The denser aqueous layer (containing sodium acetate) will settle at the bottom, while the less dense organic layer (containing ethoxyethane) will float on top.
When acetic acid and ethoxyethane are dissolved in tert-butyl methyl ether and subjected to aqueous sodium hydroxide in a separatory funnel, the addition of NaOH will result in the formation of two distinct layers. The aqueous layer will contain sodium acetate formed from the reaction between acetic acid and NaOH, while the organic layer will retain ethoxyethane. This separation process allows for the isolation of the desired compounds based on their differing solubilities and acid-base properties.
To know more about acetic acid , visit
https://brainly.com/question/15231908
#SPJ11
How many pounds of aluminum are in 1 gallon of aluminum sulfate
assuming 5.4 lbs per gallon?
Answer: 5.4 Pounds Aluminium
Given that 5.4 lbs of aluminum per gallon of aluminum sulfate;
we are to find how many pounds of aluminum are in 1 gallon of aluminum sulfate.
The pounds of aluminum in 1 gallon of aluminum sulfate assuming 5.4 lbs per gallon can be found by multiplying the given lbs of aluminum per gallon by 1.
So, the pounds of aluminum in 1 gallon of aluminum sulfate are 5.4 lbs (given).
Therefore, 5.4 pounds of aluminum are in 1 gallon of aluminum sulfate when assuming 5.4 lbs per gallon.
A salt with the formula Al2(SO4)3 is aluminium sulphate. It is soluble in water and is primarily employed as a coagulating agent in the purification of drinking water and wastewater treatment plants, as well as in the production of paper. This agent promotes particle collision by neutralising charge.
. Anhydrous aluminium sulphate is very infrequently seen. It can produce a variety of hydrates, the most prevalent of which are the hexadecahydrate Al2(SO4)316H2O and octadecahydrate Al2(SO4)318H2O.
Know more about Aluminium here:
https://brainly.com/question/28663566
#SPJ11