the manganese content of a certain stainless steel is to be verified by an activation measurement. the activity induced in a sample of volume v by neutron capture during a time t is given by

Answer:

its B. ima keep it short its B

Explanation

The owner of a building designed by registered engineers and architects may not be able to recover damages from snow and ice if the engineers and architects had specified the use of materials or building techniques that are not designed to handle those types of conditions.

Additionally, the owner may not have taken proper preventative measures to ensure the building was properly insulated and protected from the weather, or the owner may not have maintained the building appropriately. Finally, the owner may not have been able to prove negligence on the part of the engineers or architects in the building's design or construction.

In conclusion, the owner of a building designed by registered engineers and architects may not be able to recover damages from snow and ice if the building was not designed to withstand such conditions, if the owner failed to take proper preventative measures to protect the building, or if the owner could not prove negligence on the part of the engineers and architects.

You can learn more about building design at: brainly.com/question/8741590

#SPJ11

Force in all its members have increased

The vector product of mass (m) and acceleration (a) expresses the quantity of force (a). The force equation or formula can be expressed mathematically as follows:

F = ma In which case,

m = mass a = velocity

It is expressed in Newtons (N) or kilogrammes per second.

The acceleration an is provided by

a = v/t

Where

v = acceleration

t = time spent

As a result, Force can be expressed as follows:

F = mv/t

The formula for inertia is p = mv, which can also be expressed as Momentum.

As a result, force can be defined as the rate of change of momentum.

dp/dt = F = p/t

Force formulas are useful for determining the force, mass, acceleration, momentum, and velocity in any given problem.

To know more about Force,click on the link :

https://brainly.com/question/13191643

#SPJ1

The transfer function is a mathematical representation of the relationship between the input and the output of a system. The steady-state error, or ess, is the difference between the desired output and the actual output when the system reaches a steady state. The natural frequency is the frequency of the system's response without any external forces.

Transfer Function: Transfer Function is used in signal processing, control engineering, and other disciplines that deal with systems or signals. The ratio of output to input in Laplace transform is known as the transfer function.

Steady-State Error: The error that happens when the system is at a stable state is referred to as a steady-state error. The difference between the desired and actual response is known as steady-state error. A system's ability to track a specific input as time progresses is characterized by this kind of error. If the input signal is a unit step, then the steady-state error is referred to as the static error coefficient. The coefficient of the steady-state error is frequently used to classify systems in control engineering.

Natural Frequency: Natural frequency is a term used in physics to describe how quickly an object vibrates when it is set in motion. The number of oscillations made by a system in a given time period without any external force acting on it is referred to as its natural frequency. A natural frequency is a measure of a system's stiffness and mass. In a control system, it is the frequency at which the system oscillates in the absence of any input.

A natural frequency is also known as an undamped natural frequency or a resonance frequency, and it is represented by the symbol [tex]\omega_n[/tex].You can assume the following in the problem. If you have any specific values, kindly provide them.

Learn more about Transfer Function here:

https://brainly.com/question/24241688

#SPJ11

The ratio of the induced EMF in the loop CDBC to the induced EMF in the loop CADC can be calculated as follows:

ecdbc/ecadc = -dΦ_cdbc/dt / (-dΦ_cadc/dt) = dΦ_cadc/dt / dΦ_cdbc/dt

Let's dive deeper into the details below

The induced EMF is the voltage generated by a changing magnetic field in a coil of wire. In a loop, the induced EMF is proportional to the rate of change of the magnetic flux that is threading the loop. Therefore, in a loop, the induced EMF can be calculated as:

induced EMF = -dΦ/dt, where Φ is the magnetic flux threading the loop.

We can assume that both loops are parallel to the surface and therefore perpendicular to the magnetic field. This means that the magnetic flux threading each loop is proportional to the area of the loop, as follows:

Φ_cadc = B A_cadc and Φ_cdbc = B A_cdbc

Therefore, the ratio of the induced EMF in the loop CDBC to the induced EMF in the loop CADC can be calculated as follows:

ecdbc/ecadc = dΦ_cadc/dt / dΦ_cdbc/dt = (B A_cadc)/dt / (B A_cdbc)/dt = A_cadc / A_cdbc

The answer is the ratio of the areas of the loops.

Learn more about magnetic flux.

brainly.com/question/30858765

#SPJ11

a) The ideal gas equation of state and the ideal gas law is utilized to calculate the volume flow rate of air at the inlet, which is 2.73 cubic meters per second. b)  The first law of thermodynamics is employed to determine how pressure, temperature, and volume change and the determined internal energy is 108,000 J.

a) The volume flow rate of air at the inlet can be determined using the ideal gas law and the ideal gas equation of state. The equation is PV = nRT, where P is the pressure, V is the volume, n is the number of moles, R is the gas constant, and T is the temperature. Using the given values, we can determine the volume flow rate (V) to be 2.73 cubic meters per second.

b) The change in pressure, temperature, and volume can be determined using the first law of thermodynamics. The equation is ΔU = Q - W, where ΔU is the change in internal energy, Q is the heat transferred, and W is the work done. Using the given values, we can determine the change in internal energy (ΔU) to be 108,000 J.

You can learn more about the ideal gas equation at: brainly.com/question/28837405

#SPJ11

Answer:

See below.

Explanation:

Part I

Using Chart 44-2 in the textbook, we can determine the wire gauge for each given diameter

For d = 0.2576 inch, the wire gauge is 2 AWG.

For d = 0.03196 inch, the wire gauge is 20 AWG.

For d = 0.0100 inch, the wire gauge is 30 AWG.

For d = 0.1285 inch, the wire gauge is 8 AWG.

For d = 0.0508 inch, the wire gauge is 16 AWG.

Ordering the wire sizes from smallest to largest gauge, we have:

30 AWG < 20 AWG < 16 AWG < 8 AWG < 2 AWG

Circuit A

Using Ohm's law, we can calculate the resistance in the wire:

R = E/I = 12/200 = 0.06 ohms

Substituting into the formula R = 4ρπ(Id^2), we can solve for the diameter of the wire:

d = sqrt(R/(4ρπI)) = sqrt(0.06/(42503.1416*200)) = 0.064 inches

Using the engineering reference table, we can see that the wire gauge needed for Circuit A is 2 AWG.

Circuit B

Using Ohm's law, we can calculate the resistance in the wire:

R = E/I = 12/10 = 1.2 ohms

Substituting into the formula R = 4ρπ(Id^2), we can solve for the diameter of the wire:

d = sqrt(R/(4ρπI)) = sqrt(1.2/(42503.1416*10)) = 0.023 inches

Using the engineering reference table, we can see that the wire gauge needed for Circuit B is 14 AWG.

Circuit C

Using Ohm's law, we can calculate the resistance in the wire:

R = E/I = 14.6/18 = 0.811 ohms

Substituting into the formula R = 4ρπ(Id^2), we can solve for the diameter of the wire:

d = sqrt(R/(4ρπI)) = sqrt(0.811/(42503.1416*18)) = 0.060 inches

Using the engineering reference table, we can see that the wire gauge needed for Circuit C is 4 AWG.

The modulus of elasticity, also known as Young's modulus, is a measure of a material's stiffness or resistance to deformation under stress. It represents the ability of a material to resist elastic deformation when subjected to external forces.

The modulus of elasticity is calculated by dividing the applied stress by the resulting strain, and its units are usually expressed in terms of force per unit area (such as pounds per square inch or pascals).

Steel has a high modulus of elasticity, typically around 30 million psi or 200 GPa, which makes it very stiff and strong under tension. Concrete has a lower modulus of elasticity, typically around 3 to 5 million psi or 20 to 35 GPa, which makes it more flexible but less strong than steel. Wood also has a relatively low modulus of elasticity, typically around 1 to 2 million psi or 7 to 14 GPa, which makes it less stiff than steel or concrete but still quite strong for its weight.

To learn more about Young's modulus refer to:

brainly.com/question/13257353

#SPJ4

The student question is: Service conductors passing over a roof shall be securely supported by substantial structures, and for a grounded system, where the substantial structure is ___, it shall be bonded by means of a bonding jumper and listed connector to the grounded overhead service conductor.

The answer to the blank is "metallic". So, for a grounded system, where the substantial structure is metallic, it shall be bonded by means of a bonding jumper and listed connector to the grounded overhead service conductor. This ensures that the metallic structure is safely connected to the grounding system, reducing the risk of electrical shock or damage.

To learn more about connected conductors : https://brainly.com/question/31274491

#SPJ11

It is important to consider the output impedance of a signal conditioning circuit and the input impedance of the measuring device for several reasons. First, the signal conditioner’s output impedance will affect the amplitude and frequency response of the signal as it is sent to the measurement device.

1) If the impedance of the signal conditioner and the measuring device don't match, it can lead to incorrect readings.

2) Secondly, the signal conditioner’s output impedance also affects the signal-to-noise ratio, which can influence the quality of the measurements taken.

3) Lastly, the input impedance of the measuring device must match the output impedance of the signal conditioning circuit in order to ensure a low-distortion signal that accurately reflects the original signal.

In summary, it is important to consider the output impedance of the signal conditioning circuit and the input impedance of the measuring device in order to ensure accurate and high-quality measurements.

It is important to consider the output impedance of a signal conditioning circuit or the input impedance of a measuring device for optimal performance and accurate measurements. This is because the impedance values affect the signal transfer between the circuit and the device.

The input impedance of a measuring device refers to the resistance of the device input to the output impedance of the signal conditioning circuit.

If the input impedance of the device is too low, it can lead to a large current flowing from the circuit to the device, which can cause distortion and reduce the accuracy of the measurement.

On the other hand, if the input impedance is too high, it can affect the signal transfer between the circuit and the device, leading to a loss of signal strength and distortion.

For more such questions on impedance

https://brainly.com/question/29853108

#SPJ11

The Low-Level Wind Shear Alert System (LLWAS) provides wind data and software processes to detect the presence of hazardous wind shear.

LLWAS (Low-level windshear alerting systems) is a tool with a system to detect the presence of windshears close to the airport, and will provide warning windshear information automatically if has exceeded its threshold.

It works by collecting data from wind speed and direction sensors located around an airport to provide real-time monitoring of changes in wind direction and speed that can lead to hazardous wind shear events. The data is used to create an alert if hazardous wind shear is detected.

Learn more about LLWAS : https://brainly.com/question/30001468

#SPJ11

The plant will need to perform 9,100,000 processing and assembly procedures altogether.

Shape operations, property-enhancing operations, and surface processing operations are the three distinct categories of processing operations. By using mechanical force, heat, or other forms and combinations of energy, shaping operations change the work material's geometry.

There are 250 components in each product.

Parts purchased as a percentage equal 65%.

250 - (65% x 250) = 87.5 is the number of components that will be produced in the new facility.

Eight processing steps are needed to manufacture each component.

The new factory's processing procedures per component totaled 8 x 87.5, or 700.

13 x 1000 x (700 + 1) = 9,100,000 is the total number of processing and assembly procedures needed for the 13 different models.

To know more about assembly visit:-

https://brainly.com/question/13557244

#SPJ1

The coefficient of volume expansion and the coefficient of linear expansion are both thermal properties of a material that describe how its dimensions change in response to changes in temperature.

The coefficient of volume expansion (β) represents the fractional change in volume per degree of temperature change, while the coefficient of linear expansion (α) represents the fractional change in length per degree of temperature change.

For most materials, the coefficient of volume expansion is approximately three times larger than the coefficient of linear expansion. This means that the material's volume will change three times as much as its length for the same change in temperature.

For example, the coefficient of linear expansion for aluminum is around 23.1 × 10⁻⁶ /°C, while its coefficient of volume expansion is around 69 × 10⁻⁶ /°C. Similarly, the coefficient of linear expansion for glass is around 8 × 10⁻⁶ /°C, while its coefficient of volume expansion is around 24 × 10⁻⁶ /°C. The exact values can vary depending on the specific material and its composition, but the relationship between the two coefficients generally holds true.

To learn more about linear expansion refer to:

brainly.com/question/14780533

#SPJ4

The frequency response of the system H(s) is (s + 1) / (s + 3) ,  the Impulse Response of the system h(t) is δ(t) - 2e^{(-3t)u(t)} and the differential equation for this system δ(t) is  h'(t) + 3h(t)

To find the frequency response of the system, H(ω), we can use the Laplace transform:

Y(s) = H(s)X(s)

where X(s) and Y(s) are the Laplace transforms of x(t) and y(t), respectively.

Taking the Laplace transform of x(t):

X(s) = 1 / (s + 1)

Taking the Laplace transform of y(t):

Y(s) = 1 / (s + 3)

Substituting these into the equation above:

H(s) = Y(s) / X(s) = (s + 1) / (s + 3)

To find the impulse response of the system, h(t), we can take the inverse Laplace transform of H(s):

h(t) = L^-1 {H(s)} = L^-1 {(s + 1) / (s + 3)}

Using partial fraction decomposition:

H(s) = (s + 1) / (s + 3) = 1 - 2/(s+3)

Taking the inverse Laplace transform:

h(t) = L^-1 {H(s)} = L^-1 {1} - L^-1 {2/(s+3)}

h(t) = δ(t) - 2e^{(-3t)}u(t)

where δ(t) is the Dirac delta function and u(t) is the unit step function.

To find the differential equation for the system, we can use the fact that the impulse response of an LTI system is the solution to the system's differential equation.

From the above, we have:

h(t) = δ(t) - 2e^(-3t)u(t)

Taking the derivative with respect to t:

dh(t)/dt = -3h(t) + δ'(t)

where δ'(t) is the derivative of the Dirac delta function.

Since δ(t) is zero everywhere except at t=0, its derivative is zero everywhere except at t=0 where it is infinite.

Thus, the differential equation for the system is:

dh(t)/dt + 3h(t) = δ(t)

or equivalently,

h'(t) + 3h(t) = δ(t)

where h'(t) is the derivative of h(t).

To practice more questions about differential equation:

https://brainly.com/question/30417555

#SPJ11

The filter paper is placed flat on the bottom of the Hirsch funnel and wetted before collecting crystals to ensure effective filtration and prevent loss of the collected crystals.

The wetting of the filter paper helps to create a seal between the paper and the funnel, which prevents the crystals from bypassing the filter paper and being lost. The wetting of the paper also helps to eliminate air pockets or gaps that could lead to uneven filtration or channeling, which can also result in loss of the crystals. In addition, the filter paper should fit flat on the bottom of the Hirsch funnel to ensure even distribution of the crystals and to prevent them from accumulating in one area, which could also result in loss of the crystals.

Learn more about Hirsch funnel: https://brainly.com/question/30648758

#SPJ11

The longitudinal segment through the end of a finger in this virtual slide specimen is known as Hyponychium the tissue located underneath the nail plate.

The hyponychium is the area of skin beneath the free edge of the nail plate, at the distal end of the finger or toe. It is sometimes referred to as the "quick" or the "nail bed seal,"

The hyponychium is an important part of the nail unit and is composed of specialized skin cells that help to support and protect the nail.

The hyponychium plays an important role in protecting the underlying nail bed and fingertip from damage, infection, and other types of trauma. Here are some of the benefits of the hyponychium:

1) Protection: The hyponychium acts as a barrier between the nail bed and the environment, protecting the underlying tissue from injury and infection.

2) Seal: The hyponychium seals the area between the nail plate and the nail bed, preventing dirt, debris, and bacteria from getting underneath the nail and causing infection.

3) Sensation: The hyponychium contains nerve endings that provide sensory feedback to the brain, allowing us to feel pressure, touch, and other sensations

For more such questions on finger

https://brainly.com/question/29891515

#SPJ11

Note- The correct question would be as below

This is a longitudinal section through the end of a finger. What is the correct name for the area circled in this virtual slide specimen?

Answer:

Test-driven development is a great idea for software development projects, as it helps ensure that the code is properly tested and written correctly. The benefit of this approach is that it allows for more accurate debugging and testing, resulting in fewer errors in the final product. The drawback is that it can be time consuming and expensive to implement, and may require additional resources to ensure that all tests are done properly.

The lowest possible frequency of an aliased signal if a 120 kHz signal is sampled at 150 kHz is 30 kHz.

This is because the highest frequency component of a signal must be less than half the sampling frequency, or Nyquist Frequency. In this case, the Nyquist Frequency is 75 kHz, and 120 kHz is greater than 75 kHz, so it is aliased. The aliased frequency is equal to the difference between the sampling frequency and the highest frequency component, or 150 kHz - 120 kHz = 30 kHz.

Nyquist frequency is a type of sampling frequency used in signal processing which is defined as “half the rate” of a discrete signal processing system. This is the highest frequency that can be encoded for a given sampling rate so that the signal can be reconstructed.

Learn more about frequency : https://brainly.com/question/26146342

#SPJ11

You are required to leave an empty lane between your car and the emergency vehicle if it is safe, otherwise reduce speed by 20 mph is true.

A four-lane highway is a high-speed, controlled-access road with two lanes in each direction. It is often called a divided highway because of the median strip that separates the two directions of traffic. It is the most common type of multi-lane highway in the United States.

This is known as the "Move Over" law, which requires drivers to move over one lane away from any emergency vehicle with flashing lights if it is safe to do so. If it is not safe to move over, drivers are required to slow down to a speed that is at least 20 mph less than the posted speed limit. This law is in effect in many states to protect emergency responders and provide a safer working environment for them.

To learn more about speed-limit:

https://brainly.com/question/28488266

#SPJ11

Sealer should be sprayed over an original OEM finish before clearcoating. (Option B)

A sealer is a type of primer that is specifically designed to provide a smooth and uniform surface for the clearcoat to adhere to. It also helps to prevent any bleeding or discoloration from the original finish, and can improve the overall appearance of the final finish.

While primers and adhesion promoters can also be used in automotive painting, a sealer is the most appropriate product to use over an original OEM finish before clearcoating. Epoxy, on the other hand, is typically used as a primer for bare metal surfaces, rather than over an existing finish.

Learn more about OEM at:

https://brainly.com/question/17422536

#SPJ1

Technician A and Technician B both are correct as brake fluid that is allowed to remain uncovered does absorb water and brake fluid can damage the paint on a vehicle's fender if it is accidentally spilled.

Technician A is correct because brake fluid is hygroscopic, which means it absorbs moisture from the atmosphere. This water can corrode brake parts and lead to failure, as well as increase the fluid's boiling point, leading to brake fade and reduced stopping power.
Technician B is also correct because brake fluid is made up of corrosive materials that can break down paint and other surfaces. If the brake fluid is not cleaned off the fender immediately, it can cause permanent damage to the paint.

You can learn more about corrosive materials at: brainly.com/question/29632416

#SPJ11

Land surveying is the era used to gather records additionally a part of geomatics. but geomatics is a technology to discover ways to analysis that survey geospatial facts through diverse approach and making out a selection via it.

Land Surveying (or Engineering Surveying) is in truth a sub-area of Geomatics. however, in practice, there may be little to no distinction between the disciplines and the phrases get used interchangeably often.
A Geomatics engineer will employ sensors, knowledge and software to provide notably correct positional information for any of these scenarios.
Surveyors make specific measurements to decide belongings boundaries. They provide information applicable to the form and contour of the Earth's floor for engineering, mapmaking, and creation initiatives.

To know more about land surveying click on right here
brainly.com/question/29841451
#SPJ4

Answer:

When E = 14 V and R = 1 Ω, the current is 14 A.

When E = 14 V and R = 4 Ω, the current is 3.5 A.

When E = 14 V and R = 8 Ω, the current is 1.75 A.

When E = 14 V and R = 12 Ω, the current is 1.166... A
(rounded to three decimal places).

Explanation:

To calculate the current (I) using Ohm's law, we can use the formula:

I = E / R

where I is the current in amperes (A), E is the voltage in volts (V), and R is the resistance in ohms (Ω).

Answer:

Current = Emf / Resistance

When E = 14 V and R = 1 Ω, the current is 14/1 amperes = 14 amp

When E = 14 V and R = 4 Ω, the current is 14/4 amperes = 3.5 amp

When E = 14 V and R = 8 Ω, the current is 14 / 8 amperes = 1.75 amp

When E = 14 V and R = 12 Ω, the current is 14 / 12 amperes = 1.16 amp

The time constant of the system is not defined because the output signal remains at zero for all values of t. The sensitivity of the system is a = 0.

The time constant and sensitivity of a measurement system can be determined from the equation y = a (1 - e ^ -t/τ). Here, τ is the time constant and a is the sensitivity. The output signal is initially steady at 60 units and the input signal is then suddenly increased to 90 units.

The equation of the system is given by:

y = a (1 - e ^ -t/τ)

Given that the initial output signal is steady at 60 units, it implies that when t=0, y=60. Thus the equation becomes:

60 = a (1 - e ^ 0/τ)

60 = a (1 - 1)

60 = 0

This equation is not possible. It implies that the value of a is zero. Thus, the equation of the system is simplified to:

y = 0

Therefore, the answer  is a = 0.

Learn more about output signal : https://brainly.com/question/30953449

#SPJ11

Electricity is the movement of electrons between atoms.

The atomic mass or atomic weight is the total mass of an atom, including protons, neutrons, and electrons. Atomic mass units are used to measure atomic mass or weight. Electrons contribute only a small portion of the atomic structure's mass, but they play an important role in the chemical reactions that produce molecules. The atomic weight can be thought of as the number of protons plus the number of neutrons for most purposes. Because the number of neutrons in an atom can vary, most elements can have multiple atomic weights.The charges of protons and electrons are equal and opposite. Protons are positively charged, while electrons are negatively charged. Normally, atoms have an equal number of protons and neutrons.  

To know more about Atom, click on the link :

https://brainly.com/question/30898688

#SPJ1

The percent voltage regulation of the synchronous turbo alternator is  0.0826%. This indicates the ability of the machine to maintain voltage output under different load conditions.

At full load, the apparent power output of the alternator is 2500 kVA. We can find the real power output by multiplying it by the power factor:

Real power = 2500 kVA x 0.8 = 2000 kW

The current drawn by the alternator can be calculated using the real power and voltage:

Current (I) = Real power (P) / Voltage (V) = 2000 kW / 6600 V = 0.303 A

The voltage drop in the synchronous reactance can be calculated using Ohm's Law:

Voltage drop = Current x Synchronous reactance per phase = 0.303 A x 10.4 ohms = 3.15 V

The percent voltage regulation can be calculated using the following formula:

Percent voltage regulation = (Voltage drop / No-load voltage) x 100

The no-load voltage of the alternator can be calculated using the synchronous EMF equation:

No-load voltage = Line voltage / Sq. root of 3

Line voltage = 6600 V

No-load voltage = 6600 V / Sq. root of 3 = 3814 V

Substituting the values:

Percent voltage regulation = (3.15 V / 3814 V) x 100 = 0.0826 %

Therefore, the percent voltage regulation of the synchronous turbo alternator is 0.0826%.

To practice more questions about voltage regulation:

https://brainly.com/question/14407917

#SPJ11

Option B. In the 21st century, teaching is more complex because teachers have students with a wider variety of learning needs.

According to Dewey, curriculum and institutions should be secondary to children in brain-based pedagogy since learning is socially produced. Students have to apply prior knowledge to generate new meaning in order to effectively learn.

This is what makes individualized instruction complex.Individualized instruction has been emphasized since Dewey's times. However, in the 21st century, teaching is more complex because teachers have students with a wider variety of learning needs. Student-centered learning, on the other hand, has been a popular idea in education for years.

The popularity of student-centered learning can be traced back to John Dewey, a prominent educational philosopher. In Dewey's view, student-centered learning focused on the student's experience, interests, and interaction with the environment. Therefore the correct option is B.

Learn more about "teachers" at: https://brainly.com/question/28328532

#SPJ11

The given statement "Concepts are general ideas that you use to organize your experience and, in doing so, bring order and intelligibility to your life. " is true because It is important to understand what concept is and how they are useful in our daily life as it helps us organize our experiences and ideas.

Concepts are general ideas that can be used to classify and organize information. They provide structure and coherence to our perceptions and experiences. When we have a concept, it helps us bring order to our experiences and gives us a framework for understanding new information.

By organizing information into categories, we can more easily remember, process, and communicate it. This can help us make sense of the world around us and navigate our experiences in a meaningful way. In conclusion, concepts are important because they help us make sense of our experiences and the world around us. They provide structure and intelligibility to our lives, allowing us to organize and communicate our ideas and experiences more effectively.

So the statement is true.

Learn more about "intelligibility" at: https://brainly.com/question/9944825

#SPJ11

The type of sprinkler system that allows immediate and simultaneous discharge of all sprinkler heads is the deluge system.

In a deluge system, all the sprinkler heads are open and ready to discharge water at all times. The system is activated by a separate fire detection system, such as smoke detectors or heat sensors, which triggers the release of water from all the sprinkler heads at once. This makes deluge systems ideal for high hazard areas where fire can spread quickly, such as chemical storage areas or power plants.

In contrast, wet-pipe systems have water in the pipes at all times and require heat to open individual sprinkler heads, while dry-pipe and pre-action systems use compressed air or other gases to hold water back until a sprinkler head is triggered.

To learn more about sprinkler system refer to:

brainly.com/question/28992367

#SPJ4