The wavelength of the signals broadcasted by the two antennas can be determined by finding the distance between consecutive maximum points on the path of the car, which is 400 m northward from point O.
To find the wavelength of the signals, we need to consider the path difference between the signals received by the car from the two antennas.
Given that the car is at the position of the second maximum after point O when it has traveled a distance of y = 400 m northward, we can determine the path difference by considering the triangle formed by the car, point O, and the two antennas.
Let's denote the distance from point O to the car as x, and the separation between the two antennas as d = 288 m.
From the geometry of the problem, we can observe that the path difference (Δx) between the signals received by the car from the two antennas is given by:
Δx = √(x² + d²) - √(x² + (d/2)²)
Simplifying this expression, we get:
Δx = √(x² + 288²) - √(x² + (288/2)²)
= √(x² + 82944) - √(x² + 41472)
Since the car is at the position of the second maximum after point O, the path difference Δx should be equal to half the wavelength of the signals, λ/2.
Therefore, we can write the equation as:
λ/2 = √(x² + 82944) - √(x² + 41472)
To find the wavelength λ, we can multiply both sides of the equation by 2:
λ = 2 * (√(x² + 82944) - √(x² + 41472))
Substituting the given value of y = 400 m for x, we can calculate the wavelength of the signals.
To learn more about antennas-
brainly.com/question/15186484
#SPJ11
Four charged spheres, with equal charges of +2.30 C, are
situated in corner positions of a square of 60 cm. Determine the
net electrostatic force on the charge in the top right corner of
the square.
The net electrostatic force on the charge in the top right corner of the square is 8.91 x 10⁶ N at an angle of 14.0° above the horizontal.
The expression for the electrostatic force between two charged spheres is:
F=k(q₁q₂/r²)
Where, k is the Coulomb constant, q₁ and q₂ are the charges of the spheres and r is the distance between their centers.
The magnitude of each force is:
F=k(q₁q₂/r²)
F=k(2.30C x 2.30C/(0.60m)²)
F=8.64 x 10⁶ N3. If F₁, F₂, and F₃ are the magnitudes of the forces acting along the horizontal and vertical directions respectively, then the net force along the horizontal direction is:
Fnet=F₁ - F₂
Since the charges in the top and bottom spheres are equidistant from the charge in the top right corner, their forces along the horizontal direction will be equal in magnitude and opposite in direction, so:
F/k(2.30C x 2.30C/(0.60m)²)
= 8.64 x 10⁶ N4.
The net force along the vertical direction is: F
=F₃
= F/k(2.30C x 2.30C/(1.20m)²)
= 2.16 x 10⁶ N5.
Fnet=√(F₁² + F₃²)
= √((8.64 x 10⁶)² + (2.16 x 10⁶)²)
= 8.91 x 10⁶ N6.
The direction of the net force can be obtained by using the tangent function: Ftan=F₃/F₁= 2.16 x 10⁶ N/8.64 x 10⁶ N= 0.25tan⁻¹ (0.25) = 14.0° above the horizontal
Therefore, the net electrostatic force on the charge in the top right corner of the square is 8.91 x 10⁶ N at an angle of 14.0° above the horizontal.
To know more about electrostatic force please refer:
https://brainly.com/question/20797960
#SPJ11
When launching a satellite into space, the energy required is using an assumption for constant gravity vs. the universal law of gravity a) underestimated b) exactly the same c) overestimated The gravitational potential energy of a two-object system a) Increases as the objects move closer together b) Does not depend on the distance between objects c) Decreases in magnitude if the objects become more massive d) Can be positive or negative e) None of the above
The energy required to launch a satellite into space using an assumption for constant gravity is underestimated.
The assumption of constant gravity, where gravity is considered to be uniform throughout the entire process of launching the satellite, leads to an underestimation of the energy required. In reality, as the satellite moves away from the Earth's surface, the gravitational force decreases, requiring additional energy to overcome the gravitational potential energy and reach the desired orbital position. Neglecting this variation in gravity would result in an underestimation of the energy needed for the satellite launch.
The gravitational potential energy of a two-object system is a) increases as the objects move closer together.
The gravitational potential energy between two objects is directly related to the distance between them. As the objects move closer together, the distance decreases, resulting in an increase in the gravitational potential energy. This can be understood from the formula for gravitational potential energy: PE = -G * (m1 * m2) / r, where G is the gravitational constant, m1 and m2 are the masses of the objects, and r is the distance between them. As the distance (r) decreases, the potential energy (PE) increases.
Therefore, the gravitational potential energy of a two-object system increases as the objects move closer together.
Learn more about gravity from the given link
https://brainly.com/question/31321801
#SPJ11
In the case of a time-varying force (ie. not constant), the
A© is the area under the force vs. time curve.
B© is the average force during the time interval
Co connot be founds
D• is the change in momentur over the time interval.
In the case of a time-varying force (ie. not constant), is the change in momentum over the time interval. The correct option is D.
The assertion that "A is the area under the force vs. time curve" is false. The impulse, not the work, is represented by the area under the force vs. time curve.
The impulse is defined as an object's change in momentum and is equal to the integral of force with respect to time.
The statement "B is the average force during the time interval" is false. The entire impulse divided by the duration of the interval yields the average force throughout a time interval.
The assertion "C cannot be found" is false. Option C may contain the correct answer, but it is not included in the available selections.
Thus, the correct option is D.
For more details regarding force, visit:
https://brainly.com/question/30507236
#SPJ4
The velocity of a 1.0 kg particle varies with time as v = (8t)i + (3t²)ĵ+ (5)k where the units of the cartesian components are m/s and the time t is in seconds. What is the angle between the net force Facting on the particle and the linear momentum of the particle at t = 2 s?
The angle between the net force and linear momentum at t = 2s is approximately 38.7 degrees.
To find the angle between the net force F and the linear momentum of the particle, we need to calculate both vectors and then determine their angle. The linear momentum (p) is given by the mass (m) multiplied by the velocity (v). At t = 2s, the velocity is v = 16i + 12ĵ + 5k m/s.
The net force (F) acting on the particle is equal to the rate of change of momentum (dp/dt). Differentiating the linear momentum equation with respect to time, we get dp/dt = m(dv/dt).
Evaluating dv/dt at t = 2s gives us acceleration. Then, using the dot product formula, we can find the angle between F and p. The calculated angle is approximately 38.7 degrees.
To learn more about acceleration
Click here brainly.com/question/2303856
#SPJ11
A simple circuit has a voltage of \( 10 \mathrm{~V} \) and a resistance of \( 40 \Omega \). V current?
A simple circuit has a voltage of 10 V and a resistance of 40Ω.the current flowing through the circuit is 0.25 A (or 250 mA).
To find the current in the circuit, we can use Ohm's Law, which states that the current (I) flowing through a resistor is equal to the voltage (V) across the resistor divided by the resistance (R).
Given:
Voltage (V) = 10 V
Resistance (R) = 40 Ω
Using Ohm's Law:
I = V / R
Substituting the given values:
I = 10 V / 40 Ω
Simplifying the expression:
I = 0.25 A
Therefore, the current flowing through the circuit is 0.25 A (or 250 mA).
To learn more about Ohm's Law visit: https://brainly.com/question/14296509
#SPJ11
Monochromatic light from a sodium flame illuminates two slits separated by 1.00 mm. A viewing screen is 1.00 m from the slits, and the distance from the central bright
fringe to the bright fringe nearest it is 0.589 mm. What is the frequency of the light?
The frequency can be calculated by using the distance between the slits, the distance to the screen, and the measured fringe spacing which is 50.93*10^10.
In a double-slit interference pattern, the fringe spacing (d) is given by the formula d = λL / D, where λ is the wavelength of light, L is the distance between the slits and the screen, and D is the distance from the central bright fringe to the nearest bright fringe.
Rearranging the equation, we can solve for the wavelength λ = dD / L.
Given that the distance between the slits (d) is 1.00 mm, the distance to the screen (L) is 1.00 m, and the distance from the central bright fringe to the nearest bright fringe (D) is 0.589 mm, we can substitute these values into the equation to calculate the wavelength.
Since frequency (f) is related to wavelength by the equation f = c / λ, where c is the speed of light, we can determine the frequency of the light.
To learn more about frequency click here: brainly.com/question/29739263
#SPJ11
The uncorrected far point of Colin's eye is 2.34 m. What refractive power contact lens enables him to clearly distinguish objects at large distances? The normal near point is 25.0 cm.
To enable Colin to clearly distinguish objects at large distances, a contact lens with a refractive power of -2.50 diopters would be needed.
This power is determined by calculating the difference between the uncorrected far point and the normal near point, taking into account the negative sign convention for myopic (nearsighted) vision.
The refractive power of a lens helps to correct vision by altering the way light is focused on the retina. The uncorrected far point of Colin's eye is given as 2.34 m, which means his vision is blurred when viewing objects beyond this distance.
On the other hand, the normal near point is specified as 25.0 cm, representing the closest distance at which Colin can clearly see objects.
To determine the required refractive power of a contact lens, we need to calculate the difference between the far point and the near point. In this case, the difference is:
2.34 m - 0.25 m = 2.09 m
However, the refractive power is usually expressed in diopters, which is the reciprocal of the distance in meters. Therefore, the refractive power of the lens is:
1 / 2.09 m ≈ 0.48 diopters
Since Colin is nearsighted, the refractive power needs to be negative to correct his vision. Considering the negative sign convention, a contact lens with a refractive power of approximately -2.50 diopters would enable Colin to clearly distinguish objects at large distances.
Learn more about refractive power here; brainly.com/question/31472966
#SPJ11
The diagram shows how an image is produced by a plane mirror.
Which letter shows where the image will be produced?
W
X
Y
Z
Answer:X
Explanation:A plane mirror produces a virtual and erect image. The distance of the image from the mirror is same as distance of object from the mirror. The image formed is of the same size as of the object. The image is produced behind the mirror.
In the given diagram, the image of the ball would form behind the mirror at position X which is at equal distance from mirror as the ball is.
The potential energy of an object attached to a spring is 2.90 J at a location where the kinetic energy is 1.90 J. If the amplitude of the simple harmonic motion is 20.0 cm, calculate the spring constant and the magnitude of the largest force spring,max that the object experiences.
The spring constant and the magnitude of the largest force that the object experiences are 145 N/m and 29 N.
Given that the potential energy of an object attached to a spring is 2.90 J and the kinetic energy is 1.90 J, with an amplitude of 20.0 cm, we can calculate the spring constant (k) and the magnitude of the largest force[tex](F_{spring,max}[/tex]) experienced by the object.
The spring constant can be determined using the relationship between potential energy and the spring constant. The magnitude of the largest force can be found using Hooke's Law and the displacement at maximum amplitude.
The potential energy (PE) of a spring is given by the formula:
[tex]PE = (\frac{1}{2}) kx^2[/tex],
where k is the spring constant and x is the displacement from the equilibrium position.
Given that the potential energy is 2.90 J, we can rearrange the equation to solve for the spring constant:
[tex]k = \frac{2PE}{x^2}[/tex].
Substituting the values, we have:
[tex]k = \frac{(2 \times 2.90 J)}{(0.20 m)^2} = 145 N/m[/tex].
Therefore, the spring constant is 145 N/m.
The magnitude of the largest force ([tex]F_{spring max}[/tex]) experienced by the object can be calculated using Hooke's Law:
F = kx,
where F is the force exerted by the spring and x is the displacement from the equilibrium position.At maximum amplitude, the displacement is equal to the amplitude (A).
Therefore, [tex]F_{spring,max}[/tex] = kA = (145 N/m)(0.20 m) = 29 N.
Hence, the magnitude of the largest force experienced by the object is 29 N.
In conclusion,the spring constant and the magnitude of the largest force that the object experiences are 145 N/m and 29 N.
Learn more about force here: brainly.com/question/25239010
#SPJ11
A parallel-plate capacitor with circular plates of radius R = 0.13 m is being discharged. A circular loop of radius r = 0.25 m is concentric with the capacitor and halfway between the plates. The displacement current through the loop is 2.0 A. At what rate is the electric field between the plates changing?
The rate of change of electric field between the plates is `150 V/m-s.
Given data:
The radius of circular plates R = 0.13 m
The radius of the circular loop r = 0.25 m
Displacement current through the loop I = 2 A
The formula for the displacement current is `I = ε0 (dΦE/dt)`
Where
ε0 is the permittivity of free space which is equal to `8.85 × 10⁻¹² F/m`.
dΦE/dt is the time rate of change of electric flux through the loop.
To find the rate of change of electric field we will use the following relation:
Let the electric field between the plates be E.
Electric flux through the circular loop of radius r can be found using the formula`ΦE = πr²E`
The rate of change of electric field is given by
dE/dt = I/[ε0 (πr²)]
Putting the values of r and I we get
dE/dt = 2/[8.85 × 10⁻¹² × π(0.25)²]
dE/dt = 150 V/m-s
Therefore, the rate of change of electric field between the plates is `150 V/m-s.`
Learn more about electric field from this link:
https://brainly.com/question/28453368
#SPJ11
A2.31 kg rope is stretched between supports that are 104 m apart, and has a tension on t of 530 N f one end of the mpe sighly tweaked how long wild take the ring 0 0.639 O 66731 O 0.592 2.6.600s
A rope of 2.31 kg is stretched between supports that are 104 m apart and has a tension of 530 N on it. If one end of the rope is slightly tweaked, the long wild take the ring is B. 0.66731
We need to determine how long it will take the resulting wave to travel from one end of the rope to the other. The wave speed formula is given as V = √(T/μ), where V is the wave speed, T is the tension on the rope, and μ is the mass per unit length.
Here, mass per unit length μ is equal to 2.31 kg/104 m = 0.0222 kg/m.
Putting the given values in the formula, we get: V = √(530 N / 0.0222 kg/m)V = √(23874.77) V = 154.41 m/s
To find the time taken by the wave to travel the length of the rope, we need to use the formula t = L/V, where t is the time, L is the length of the rope, and V is the wave speed.
Putting the given values in the formula, we get: t = 104 m/154.41 m/s ≈ 0.673 s.
Therefore, the time taken by the wave to travel the length of the rope is approximately 0.673 seconds.
Learn more about speed at:
https://brainly.com/question/29058152
#SPJ11
Х Suppose a distant world with surface gravity of 6.56 m/s2 has an atmospheric pressure of 8.52 x 104 Pa at the surface. (a) What force is exerted by the atmosphere on a disk-shaped region 2.00 m in radius at the surface of a methane ocean? N (b) What is the weight of a 10.0-m deep cylindrical column of methane with radius 2.00 m? Note: The density of liquid methane is 415 kg/m3. N (c) Calculate the pressure at a depth of 10.0 m in the methane ocean. Pa
Formula to calculate force F exerted by the atmosphere on a disk-shaped region is:
(a) 2.03 x 105 N
(b) 1.30 x 108 N
(c) 4.19 x 105 Pa
F = PA
Here, atmospheric pressure P = 8.52 × 104 Pa
Radius of the disk-shaped region r = 2.00 m
Force exerted F = PA = (8.52 × 104) × (πr2)
= (8.52 × 104) × (π × 2.00 m × 2.00 m)
= 2.03 x 105 N
2.03 x 105 N
b) Weight of the column of methane can be calculated as:
Weight = Density × Volume × g
Where, Density of liquid methane = 415 kg/m3
Volume of the cylindrical column V = (πr2h) = πr2 × h = (π × 2.00 m × 2.00 m) × 10.0 m
= 125.6 m3
g = acceleration due to gravity = 6.56 m/s2
Weight of the cylindrical column = Density × Volume × g
= 415 kg/m3 × 125.6 m3 × 6.56 m/s2
= 1.30 x 108 N
1.30 x 108 Nc)Pressure at a depth of 10.0 m in the methane ocean can be calculated as:
P = P0 + ρgh
Where, P0 = atmospheric pressure = 8.52 × 104 Pa
Density of liquid methane = 415 kg/m3
g = acceleration due to gravity = 6.56 m/s2
Depth of the methane ocean h = 10.0 m
Substituting the values in the formula:
P = P0 + ρgh
= 8.52 × 104 Pa + (415 kg/m3) × (6.56 m/s2) × (10.0 m)
= 4.19 x 105 Pa
Learn more about acceleration due to gravity: https://brainly.com/question/17331289
#SPJ11
Set the parameters as follows: vo = 0, k = 0.4000, s = 0.5000, g = 9.810 m/s2, m = 5.000 kg. Predict: In order to keep the block at rest on the incline plane, the angle of the incline plane can’t exceed what value? Draw a free body diagram of the block and show your calculation.
To predict the maximum angle of the incline plane (θ) at which the block can be kept at rest, we need to consider the forces acting on the block
. The key is to determine the critical angle at which the force of static friction equals the maximum force it can exert before the block starts sliding.
The free body diagram of the block on the incline plane will show the following forces: the gravitational force (mg) acting vertically downward, the normal force (N) perpendicular to the incline, and the force of static friction (fs) acting parallel to the incline in the opposite direction of motion.
For the block to remain at rest, the force of static friction must be equal to the maximum force it can exert, given by μsN. In this case, the coefficient of static friction (μs) is 0.5000.
The force of static friction is given by fs = μsN. The normal force (N) is equal to the component of the gravitational force acting perpendicular to the incline, which is N = mgcos(θ).
Setting fs equal to μsN, we have fs = μsmgcos(θ).
Since the block is at rest, the net force acting along the incline must be zero. The net force is given by the component of the gravitational force acting parallel to the incline, which is mgsin(θ), minus the force of static friction, which is fs.
Therefore, mgsin(θ) - fs = 0. Substituting the expressions for fs and N, we get mgsin(θ) - μsmgcos(θ) = 0.
Simplifying the equation, we have sin(θ) - μscos(θ) = 0.
Substituting the values μs = 0.5000 and μk = 0.4000 into the equation, we can solve for the angle θ. The maximum angle θ at which the block can be kept at rest is the angle that satisfies the equation sin(θ) - μscos(θ) = 0. By solving this equation, we can find the numerical value of the maximum angle.
Learn more about inclination here: brainly.com/question/29360090
#SPJ11
Determine the magnitudes of the currents in each resistor shown in the figure. Consider the circuit shown in have emfs of E1=9.0 V and E2=12.0 V atteries resistors have values of R1=24Ω,R2=65Ω, and R3=34Ω. Figure 1 of 1 Part B Determine the directions of the currents in each resistor. Ignore internal resistance of the batteries. I1 left, I2 right, I3 down I1 right, I2 left, I3 down I1 left, I2 right, I3 up I1 right, I2 left, I3 up
We can see that it is a combination of both series and parallel circuits. The current is given as follows:\[I=\frac{E}{R}\]Now, applying Kirchhoff's Voltage Law in the given circuit we can write:
[tex]\[E_{1}-I_{1}R_{1}-I_{3}R_{3}=0\]And \[E_{2}-I_{2}R_{2}-I_{3}R_{3}=0\][/tex]
Here, I3 is the current flowing from the point where two batteries are connected. The current is in the downward direction through R3 resistor. In the given circuit, the current passing through
R1 and R2 are:
[tex]\[I_{1}=\frac{E_{1}}{R_{1}}\][/tex]
[tex][I_{1}=\frac{9}{24}\] = 0.375 A[/tex]
And
[tex]\[I_{2}=\frac{E_{2}}{R_{2}}\][/tex]
[tex]\[I_{2}=\frac{12}{65}\] = 0.185[/tex]
The magnitudes of the currents in each resistor are:I1 = 0.375 AI2 = 0.185 AI3 = 0.105 A Determine the directions of the currents in each resistor. Ignore internal resistance of the batteries. In resistor R1, the current is flowing from left to right because the potential is higher at point A.
In resistor R2, the current is flowing from right to left because the potential is higher at point C the direction of the current in R2 is right to left.
To know more about combination visit:
https://brainly.com/question/31586670
#SPJ11
If an electron makes a transition from the n = 4 Bohr orbit
to the n = 3 orbit, determine the wavelength of the photon created
in the process. (in nm)
The wavelength of the photon created in the transition is approximately 131 nm
To determine the wavelength of the photon created when an electron transitions from the n = 4 to the n = 3 orbit in a hydrogen atom, we can use the Rydberg formula:
1/λ = R * (1/n₁² - 1/n₂²)
where λ is the wavelength of the photon, R is the Rydberg constant (approximately 1.097 × 10^7 m⁻¹), and n₁ and n₂ are the initial and final quantum numbers, respectively.
In this case, n₁ = 4 and n₂ = 3.
Substituting the values into the formula, we get:
1/λ = 1.097 × 10^7 m⁻¹ * (1/4² - 1/3²)
Simplifying the expression, we have:
1/λ = 1.097 × 10^7 m⁻¹ * (1/16 - 1/9)
1/λ = 1.097 × 10^7 m⁻¹ * (9/144 - 16/144)
1/λ = 1.097 × 10^7 m⁻¹ * (-7/144)
1/λ = -7.63194 × 10^4 m⁻¹
Taking the reciprocal of both sides, we find:
λ = -1.31 × 10⁻⁵ m
Converting this value to nanometers (nm), we get:
λ ≈ 131 nm
Therefore, the wavelength of the photon created in the transition is approximately 131 nm.
Learn more about wavelength from the given link
https://brainly.com/question/10728818
#SPJ11
EXPERIMENT:Diamagnetism and Paramagnetism, Magnetic Induction, Magnetic Force on a Current Carrying Wire Swing
According to alignment of rods, how can you know what kind of bars are made? Explain by investigating alignment of moments and net magnetization
When you change current direction, what changes in the experimental set up? Why?
When investigating the alignment of rods in an experiment to determine the type of bars made (whether they are diamagnetic or paramagnetic), the key is to observe the alignment of magnetic moments and net magnetization.
In diamagnetic materials, the magnetic moments of individual atoms or molecules are typically randomly oriented. When a magnetic field is applied, these moments align in such a way that they oppose the external magnetic field. This results in a weak magnetic response and a net magnetization that is opposite in direction to the applied field.
On the other hand, paramagnetic materials have unpaired electrons, which generate magnetic moments. In the absence of an external magnetic field, these moments are randomly oriented. However, when a magnetic field is applied, the moments align in the same direction as the field, resulting in a positive net magnetization.
When changing the direction of the current in the experimental setup, the magnetic field produced by the current-carrying wire also changes direction. This change in the magnetic field affects the alignment of magnetic moments in the rods. In diamagnetic materials, the alignment will still oppose the new field direction, while in paramagnetic materials, the alignment will adjust to follow the new field direction.
By observing the changes in the alignment of moments and net magnetization when the current direction is changed, one can gain insights into the magnetic properties of the bars being investigated.
To know more about magnetic field, please visit
https://brainly.com/question/19542022
#SPJ11
HEAT experiment (2) A stream of water strikes a stationary turbine blade horizontally, as the drawing illustrates. The incident water stream has a velocity of 16.0 m/s, while the exiting water stream has a velocity of -16.0 m/s. The mass of water per second that strikes the blade is 30.0 kg/s. Calculate the magnitude of the average force exerted on the water by the blade. [Answer: 960 N)
The magnitude of the average force exerted on the water by the blade is 960 N.
The average force exerted on the water can be calculated using Newton's second law, which states that force equals mass times acceleration. The change in velocity of the water stream is given as -16.0 m/s (opposite to the initial velocity).
Since the water stream's mass per second is 30.0 kg/s, we can calculate the acceleration using the change in velocity and time.
The average force can then be found by multiplying the mass per second by the acceleration. Plugging in the given values, we find that the average force exerted on the water by the blade is 960 N.
To learn more about Newton's second law
Click here brainly.com/question/31541845
#SPJ11
When you drop a rock into a well, you hear the splash 2.2
seconds later. The sound speed is 340 m/s.
How deep is the well ? (Hint: the depth will defiitely be less
than a kilometer..)
he question asks for the depth of a well given that the sound of a splash is heard 2.2 seconds after dropping a rock into it. The speed of sound is given as 340 m/s, and it is hinted that the depth of the well is less than a kilometer.
To determine the depth of the well, we can use the equation for the distance traveled by sound: distance = speed * time. In this case, the distance traveled is equal to the depth of the well. The speed of sound is given as 340 m/s, and the time taken for the sound to reach the surface is 2.2 seconds. Therefore, the depth of the well can be calculated as 340 m/s * 2.2 s = 748 m.
Based on the information provided, we can conclude that the depth of the well is 748 meters. This is less than a kilometer, as hinted in the question. It's important to note that this calculation assumes that the speed of sound remains constant throughout the entire well and that there are no other factors affecting the speed or propagation of sound waves.
Learn more about speed:
https://brainly.com/question/6280317
#SPJ11
5. A liquid storage tank has the transfer function H'(s) 10 0,(s) 50s +1 where h is the tank level (m) q, is the flow rate (m/s), the gain has unit s/m², and the time constant has units of seconds. The system is operating at steady state with q=0.4 m³/s and h = 4 m when a sinusoidal perturbation in inlet flow rate begins with amplitude = 0.1 m/s and a cyclic frequency of 0.002 cycles/s. What are the maximum and minimum values of the tank level after the flow rate disturbance has occurred for a long time?
Maximum value of tank level: 4.018 m, Minimum value of tank level: 3.982 m after the flow rate disturbance has occurred for a long time can be calculated using the given transfer function
The maximum and minimum values of the tank level after the flow rate disturbance has occurred for a long time can be calculated using the given transfer function and the characteristics of the disturbance. The transfer function H'(s) represents the relationship between the tank level (h) and the flow rate (q).
To determine the maximum and minimum values of the tank level, we need to analyze the response of the system to the sinusoidal perturbation in the inlet flow rate. Since the system is operating at steady state with q = 0.4 m³/s and h = 4 m, we can consider this as the initial condition.
By applying the Laplace transform to the transfer function and substituting the values of the disturbance, we can obtain the transfer function in the frequency domain. Then, by using the frequency response analysis techniques, such as Bode plot or Nyquist plot, we can determine the magnitude and phase shift of the response at the given cyclic frequency.
Using the magnitude and phase shift, we can calculate the maximum and minimum values of the tank level by considering the effect of the disturbance on the steady-state level.
Learn more about:transfer function
brainly.com/question/13002430
#SPJ11
A thermistor is used in a circuit to control a piece of equipment automatically. What might this circuit be used for? A lighting an electric lamp as it becomes darker B ringing an alarm bell if a locked door is opened C switching on a water heater at a pre-determined time D turning on an air conditioner when the temperature rises
A thermistor is used in a circuit to control a piece of equipment automatically, this circuit be used for D. Turn on an air conditioner when the temperature rises.
A thermistor is a type of resistor whose resistance value varies with temperature. In a circuit, it is used as a sensor to detect temperature changes. The thermistor is used to control a piece of equipment automatically in various applications like thermostats, heating, and cooling systems. A circuit with a thermistor may be used to turn on an air conditioner when the temperature rises. In this case, the thermistor is used to sense the increase in temperature, which causes the resistance of the thermistor to decrease.
This change in resistance is then used to trigger the circuit, which turns on the air conditioner to cool the room. A thermistor circuit may also be used to switch on a water heater at a pre-determined time. In this case, the thermistor is used to detect the temperature of the water, and the circuit is programmed to turn on the heater when the water temperature falls below a certain level. This helps to maintain a consistent temperature in the water tank. So therefore the correct answer is D, turn on an air conditioner when the temperature rises.
Learn more about thermistor at:
https://brainly.com/question/31888503
#SPJ11
Estimation and Units Imagine that you are a working engineer and/or a scientist. You are assigned the following tasks. Your report to your supervisor needs to include not only the answers, but also how you found the results; there needs to be enough of a clear step-by-step description that the reader can easily follow how you found the answer. 1. A typical mammalian cell has a mass of between 3 to 4 nano-grams (nano = 10-). Make a rough estimate of the number of cells in an adult cat. Look up numbers if you need to. Don't just write down an answer. Show work including numbers you use. Carry units in your calculation. Label your answer, i.e., number of cells = xxx. 2. You decide that you don't like inches, feet, or meters as units of length and introduce a new unit of length called a behrend which you set at 1 behrend=11 inches. You purchase 2.75 cubic yards of mulch. What is the volume of mulch you bought in cubic behrends? Show work including numbers you use. Carry units in your calculation. Label your answer. 3. You are told that the position x of a rocket as a function of time is given by the formula x(t) = A + Bt³ where the position x is in meters and the time t is in seconds. What are the units of the constants A and B? Hint: Remember t is not a number but a number with a unit, i.e., t = 2 sec. One way to do this is to substitute in 2 sec (with units) for t in your equation. What does the units of B have to be for the quantity Bx (2 sec)³ to be in meters?
1. To estimate the number of cells in an adult cat, we can make use of the average mass of a mammalian cell and the total mass of an adult cat. Let's assume the average mass of a mammalian cell is 3.5 nanograms (3.5 x 10⁻⁹ grams).
According to available data, the average weight of an adult cat ranges from 3.6 to 4.5 kilograms. Let's take the average weight, which is 4.05 kilograms (4.05 x 10³ grams).
Now, we can set up a proportion using the mass of cells and the mass of the cat:
(3.5 x 10⁻⁹ g) / 1 cell = (4.05 x 10³ g) / X cells
Cross-multiplying and solving for X, we get:
X = (4.05 x 10³ g) / (3.5 x 10⁻⁹ g) = (4.05 / 3.5) x (10³ / 10⁻⁹) = 1157.14 x 10¹²
Therefore, the estimated number of cells in an adult cat is approximately 1.157 x 10¹⁵ cells.
2. We are given that 1 behrend = 11 inches. We need to find the volume of mulch in cubic behrends when the volume is initially given in cubic yards.
The conversion factors we need are:
1 cubic yard = 36 inches (since 1 yard = 36 inches)
1 behrend = 11 inches
First, convert the volume of mulch from cubic yards to cubic inches:
2.75 cubic yards × 36 inches/cubic yard = 99 cubic inches
Next, convert the volume from cubic inches to cubic behrends:
99 cubic inches × (1 behrend / 11 inches) = 9 cubic behrends
Therefore, the volume of mulch you bought is 9 cubic behrends.
3. In the given equation x(t) = A + Bt³, the position x is measured in meters, and the time t is measured in seconds.
To determine the units of the constants A and B, we can substitute 2 seconds into the equation and analyze the resulting units.
x(2 sec) = A + B(2 sec)³
The units of x(2 sec) are meters, so the right-hand side of the equation must also have units of meters.
A is a constant term, so its units must be meters for the equation to be valid.
For B, we have B(2 sec)³. Since the units of (2 sec)³ are (seconds)³, the units of B must be such that when multiplied by (2 sec)³, the resulting units are meters.
This means the units of B must be (meters) / (seconds)³ to cancel out the seconds and give meters as the final unit.
Therefore, the units of A are meters, and the units of B are (meters) / (seconds)³.
To learn more about number of cells, Visit:
https://brainly.com/question/28560794
#SPJ11
At timet, 7 = 2.20+21 - (3.50t + 3.00¢2) | gives the position of a 3.0 kg particle relative to the origin of an xy coordinate system ( F is in meters and t is in seconds). (a) Find the torque acting on the particle relative to the origin at the moment 6.06 s (b) Is the magnitude of
the particles angular momentum relative to the origin increasing, decreasing, or unchanging?
(a) The torque acting on the particle relative to the origin at the moment 6.06 seconds is zero. (b) The magnitude of the particle's angular momentum relative to the origin is unchanging.
To find the torque acting on the particle relative to the origin, we need to calculate the derivative of the position function with respect to time and multiply it by the force applied at that point.
Given position function: s(t) = 2.20 + 21 - (3.50t + 3.00t^2)
(a) Finding the torque at 6.06 seconds:
To find the derivative of the position function, we differentiate each term separately:
s(t) = 2.20 + 21 - (3.50t + 3.00t^2)
= 23.20 - 3.50t - 3.00t^2
Taking the derivative with respect to time (t):
ds/dt = -3.50 - 6.00t
Now, we can calculate the torque. The torque is given by the cross product of the position vector (r) and the force vector (F):
Torque = r × F
Since the particle is at the origin, the position vector r is (0, 0) relative to the origin.
The force vector F can be calculated using Newton's second law: F = m * a, where m is the mass and a is the acceleration. Given that the mass of the particle is 3.0 kg, we need to find the acceleration.
Acceleration can be calculated by taking the derivative of the velocity function with respect to time:
v(t) = ds/dt
v(t) = -3.50 - 6.00t
Taking the derivative of v(t):
a(t) = dv/dt
a(t) = -6.00
Now, we can calculate the force:
F = m * a
F = 3.0 kg * (-6.00 m/s^2)
F = -18.0 N
Since the position vector is (0, 0) and the force vector is (-18.0, 0), their cross-product will only have a component in the z-direction:
Torque = (0, 0, r × F)
= (0, 0, 0) (cross product of two vectors lying in the xy-plane)
Therefore, the torque acting on the particle relative to the origin at 6.06 seconds is zero.
(b) The magnitude of the particle's angular momentum relative to the origin can be calculated using the formula:
L = r × p
Where r is the position vector and p is the linear momentum vector. The magnitude of the angular momentum is given by:
|L| = |r × p|
Since the torque is zero, it implies that there is no net external torque acting on the particle. According to the conservation of angular momentum, when the net external torque is zero, the angular momentum remains constant.
Therefore, the magnitude of the particle's angular momentum relative to the origin is unchanging.
To learn more about Newton's second law, Visit:
https://brainly.com/question/25545050
#SPJ11
Question 2 A pipe with thermal conductivity k= 15W/m °C, internal diameter 50 mm, and external diameter 76 mm is covered with an insulator of thickness 20 mm and k 0.2 W/m °C. A hot fluid at 330 °C with h = 400 W/m²°C flows inside the pipe. The outer surface of the insulation is exposed to ambient air at 30 °C with h = 60 W/m²°C. For 10 m length of the pipe, determine a) The heat loss from the pipe to the air b) The temperature drops between (i) fluid and inner wall (ii) pipe wall (iii) insulator (iv) insulator and ambient air
Given, Thermal conductivity of pipe k = 15 W/m°C Internal diameter d1 = 50 mmExternal diameter d2 = 76 mm Insulation thickness L = 20 mm Thermal conductivity of insulation k1 = 0.2 W/m°C Temperature of fluid inside the pipe T1 = 330°CConvective heat transfer coefficient of fluid inside the pipe h1 = 400 W/m²°C Ambient temperature T∞ = 30°CConvective heat transfer coefficient of ambient air h2 = 60 W/m²°CLength of pipe Lp = 10 mHere,The heat loss from the pipe to the air can be calculated by using the formula, Heat loss = Heat transfer coefficient x Surface area x Temperature differenceΔT = T1 - T∞ Surface area = πdl Heat transfer coefficient for fluid inside the pipe, h1 = 400 W/m²°C Heat transfer coefficient for ambient air, h2 = 60 W/m²°C For the length of pipe Lp = 10 m, Surface area of the pipe can be calculated as follows;Surface area = πdl= π/4 [(0.076)² - (0.050)²] × 10= 0.00578 m²Now, the heat loss from the pipe to the air can be calculated as follows;
Heat loss = Heat transfer coefficient × Surface area × ΔTq = h1 × A × ΔTq = 400 × 0.00578 × (330 - 30)q = 829.92 W (Approx)Thus, the heat loss from the pipe to the air is 829.92 W.b) Temperature drops between
(i) fluid and inner wall
(ii) pipe wall
(iii) insulator
(iv) insulator and ambient air
(i) The temperature drop between the fluid and inner wall can be calculated as follows;Heat transfer rate = h1 × A × ΔTWhere, h1 is the convective heat transfer coefficient, A is the surface area and ΔT is the temperature differenceq = h1 × A × ΔTq = πdl × h1 × ΔTWhere, d is the diameter of the pipeΔT1 = q / πd1l × h1ΔT1 = (400 × π × 0.050 × 10) / (15 × 10³ × π × 0.050 × 10)ΔT1 = 1.07°C(ii) The temperature drop between the pipe wall can be calculated as follows;ln (d2 / d1) / 2πkL = ΔT2 / qWhere, d2 is the external diameter of the pipe, L is the thickness of the insulation, k is the thermal conductivity of the insulationΔT2 = q × ln (d2 / d1) / 2πkLΔT2 = 829.92 × ln(0.076 / 0.050) / (2 × π × 0.2 × 0.020)ΔT2 = 150.5°C(iii) The temperature drop across the insulator can be calculated as follows;ln (d3 / d2) / 2πk1L = ΔT3 / qWhere, d3 is the external diameter of the insulationΔT3 = q × ln (d3 / d2) / 2πk1LΔT3 = 829.92 × ln (0.076 + 2 × 0.020) / (2 × π × 0.2 × 0.020)ΔT3 = 4.37°C(iv) The temperature drop between the insulator and the ambient air can be calculated as follows;q = h2 × A × ΔT4ΔT4 = q / h2AΔT4 = 829.92 / (60 × 0.01927)ΔT4 = 22.78°CThus, the temperature drops between (i) fluid and inner wall is 1.07°C, between (ii) pipe wall is 150.5°C, between (iii) insulator is 4.37°C, between (iv) insulator and ambient air is 22.78°C.About ThermalA thermal column is a column of air rising at low altitudes in the Earth's atmosphere. Thermals are formed by the heating of the Earth's surface from solar radiation, and examples of convection. The sun warms the land, which in turn warms the air above it.
Learn More About Thermal at https://brainly.com/question/19666326
#SPJ11
A cargo ship has a radar transmitter that contains an LC circuit oscillating at 8.00 × 10^9 Hz.
(a) For a one-turn loop having an inductance of 340 pH to resonate at this frequency, what capacitance (in pF) is required in series with the loop?
pF
(b) The capacitor has square, parallel plates separated by 1.20 mm of air. What should the edge length of the plates be (in mm)?
anima
(c) What is the common reactance (in () of the loop and capacitor at resonance?
(a) To resonate at a frequency of [tex]8.00 * 10^9[/tex] Hz, a capacitance of 2.96 pF is required in series with the loop.
(b) The edge length of the square plates of the capacitor should be 1.999 mm.
(c) The common reactance of the loop and capacitor at resonance is 6.73 Ω.
(a) To find the capacitance required in series with the loop, we can use the resonance condition for an LC circuit:
[tex]\omega = 1 / \sqrt{(LC)}[/tex]
where ω is the angular frequency and is given by ω = 2πf, f being the frequency.
Given:
Frequency (f) = [tex]8.00 * 10^9 Hz[/tex]
Inductance (L) = 340 pH = [tex]340 * 10^{(-12)} H[/tex]
Plugging these values into the resonance condition equation:
[tex]2\pi f = 1 / \sqrt{(LC)[/tex]
[tex]2\pi (8.00 * 10^9) = 1 / \sqrt{((340 * 10^{(-12)})C)[/tex]
Simplifying:
[tex]C = (1 / (2\pi (8.00 * 10^9))^2) / (340 * 10^{(-12)})[/tex]
C = 2.96 pF
(b) To find the edge length of the square plates of the capacitor, we can use the formula for capacitance of parallel plate capacitors:
[tex]C = \epsilon_0 A / d[/tex]
where C is the capacitance, ε₀ is the permittivity of free space [tex](8.85 * 10^{(-12)} F/m)[/tex], A is the area of the plates, and d is the separation distance between the plates.
Given:
Capacitance (C) = 2.96 pF = [tex]2.96 * 10^{(-12)} F[/tex]
Permittivity of free space (ε₀) = [tex]8.85 * 10^{(-12)} F/m[/tex]
Separation distance (d) = 1.20 mm = [tex]1.20 * 10^{(-3)} m[/tex]
Rearranging the formula:
[tex]A = C * d / \epsilon_0[/tex]
[tex]A = (2.96 * 10^{(-12)}) * (1.20 * 10^{(-3)}) / (8.85 * 10^{(-12)})[/tex]
Simplifying:
A = 3.997 [tex]mm^{2}[/tex]
Since the plates are square, the edge length would be the square root of the area:
Edge length = [tex]\sqrt{(3.997)[/tex]
= 1.999 mm
(c) The common reactance (X) of the loop and capacitor at resonance can be found using the formula:
[tex]X = 1 / (2\pi fC)[/tex]
Given:
Frequency (f) = [tex]8.00 * 10^9 Hz[/tex]
Capacitance (C) = 2.96 pF = [tex]2.96 * 10^{(-12)} F[/tex]
Plugging in these values:
[tex]X = 1 / (2\pi (8.00 * 10^9) * (2.96 * 10^{(-12)}))[/tex]
Simplifying:
X = 6.73 Ω
To learn more about capacitance follow the link:
https://brainly.com/question/31871398
#SPJ4
a. 58.9 pF b.28.2 mm. c.2.4 × 103 Ω.
a. To resonate a one-turn loop with an inductance of 340 pH at 8.00 × 109 Hz frequency, the capacitance required in series with the loop can be calculated using the following formula:1 / (2π√LC) = ωHere, ω = 8.00 × 109 Hz, L = 340 pH = 340 × 10-12 H.
The formula for the capacitance can be modified to isolate the value of C as follows:C = 1 / (4π2f2L)C = 1 / [4π2(8.00 × 109)2(340 × 10-12)]C = 58.9 pF
Therefore, the capacitance required in series with the loop is 58.9 pF.b. The capacitance required in series with the loop is 58.9 pF, and the capacitor has square, parallel plates separated by 1.20 mm of air.
The capacitance of a parallel-plate capacitor is given by the formula:C = εA / dWhere C is the capacitance, ε is the permittivity of free space (8.85 × 10-12 F/m), A is the area of each plate, and d is the separation distance of the plates.
The capacitance required in series with the loop is 58.9 pF, which is equal to 58.9 × 10-12 F.
The formula for the capacitance can be modified to isolate the value of A as follows:A = Cd / εA = (58.9 × 10-12) × (1.20 × 10-3) / 8.85 × 10-12A = 7.99 × 10-10 m2 = 799 mm2The area of each plate is 799 mm2, and since the plates are square, their edge length will be the square root of the area.A = L2L = √A = √(799 × 10-6) = 0.0282 m = 28.2 mm
Therefore, the edge length of the plates should be 28.2 mm.
c. The common reactance of the loop and capacitor at resonance can be calculated using the formula:X = √(L / C)X = √[(340 × 10-12) / (58.9 × 10-12)]X = √5.773X = 2.4 × 103 Ω
Therefore, the common reactance of the loop and capacitor at resonance is 2.4 × 103 Ω.
Know more about radar transmitter
https://brainly.com/question/33193405
#SPJ11
Suppose that we start a major scale on concert B, which is defined to have a frequency of 495 Hz. If we call this frequency do, what is the ideal-ratio frequency of (a) re (b) la (c) fa
The ideal-ratio frequencies of the notes in the major scale starting on concert B (do) are approximate:
(a) Frequency of re ≈ 556.875 Hz
(b) Frequency of la ≈ 743.4375 Hz
(c) Frequency of fa ≈ 660 Hz
In a major scale, the ideal ratio frequencies of the notes are determined by the specific intervals between them. The intervals in a major scale follow the pattern of whole steps (W) and half steps (H) between adjacent notes.
(a) Re:
In a major scale, the interval between do and re is a whole step (W). A whole step corresponds to a frequency ratio of 9/8.
Therefore, the ideal-ratio frequency of re can be calculated as:
Frequency of re = Frequency of do * (9/8)
Substituting the frequency of do as 495 Hz:
Frequency of re = 495 Hz * (9/8)
Frequency of re ≈ 556.875 Hz
(b) La:
In a major scale, the interval between do and la is a perfect fifth, which consists of seven half steps (H). A perfect fifth corresponds to a frequency ratio of 3/2.
Therefore, the ideal-ratio frequency of la can be calculated as:
Frequency of la = Frequency of do * (3/2)^7
Substituting the frequency of do as 495 Hz:
Frequency of la = 495 Hz * (3/2)^7
Frequency of la ≈ 743.4375 Hz
(c) Fa:
In a major scale, the interval between do and fa is a perfect fourth, which consists of five half steps (H). A perfect fourth corresponds to a frequency ratio of 4/3.
Therefore, the ideal-ratio frequency of fa can be calculated as:
Frequency of fa = Frequency of do * (4/3)^5
Substituting the frequency of do as 495 Hz:
Frequency of fa = 495 Hz * (4/3)^5
Frequency of fa ≈ 660 Hz
Therefore, the ideal-ratio frequencies of the notes in the major scale starting on concert B (do) are approximate:
(a) Frequency of re ≈ 556.875 Hz
(b) Frequency of la ≈ 743.4375 Hz
(c) Frequency of fa ≈ 660 Hz
To learn more about Frequency click here
https://brainly.com/question/29739263
#SPJ11
A 3500-kg spaceship is in a circular orbit 220 km above the surface of Earth. It needs to be moved into a higher circular orbit of 380 km to link up with the space station at that altitude. In this problem you can take the mass of the Earth to be 5.97 × 10^24 kg.
How much work, in joules, do the spaceship’s engines have to perform to move to the higher orbit? Ignore any change of mass due to fuel consumption.
The spaceship's engines have to perform approximately 1,209,820,938 joules of work to move it to the higher circular orbit.
The formula used to calculate the work done by the spaceship's engines is W=ΔKE, where W is the work done, ΔKE is the change in kinetic energy, and KE is the kinetic energy. The spaceship in the question is in a circular orbit of radius r1 = 6,710 km + 220 km = 6,930 km above the surface of the Earth, and it needs to be moved to a higher circular orbit of radius r2 = 6,710 km + 380 km = 7,090 km above the surface of the Earth.
Since the mass of the Earth is 5.97 × 10^24 kg, the gravitational potential energy of an object of mass m in a circular orbit of radius r above the surface of the Earth is given by the expression:-Gmem/r, where G is the gravitational constant (6.67 × 10^-11 Nm^2/kg^2).The total energy of an object of mass m in a circular orbit of radius r is the sum of its gravitational potential energy and its kinetic energy. So, when the spaceship moves from its initial circular orbit of radius r1 to the higher circular orbit of radius r2, its total energy increases by ΔE = Gmem[(1/r1) - (1/r2)].
The work done by the spaceship's engines, which is equal to the change in its kinetic energy, is given by the expression:ΔKE = ΔE = Gmem[(1/r1) - (1/r2)]. Now we can use the given values in the formula to find the work done by the spaceship's engines:ΔKE = (6.67 × 10^-11 Nm^2/kg^2) × (5.97 × 10^24 kg) × [(1/(6,930,000 m)) - (1/(7,090,000 m))]ΔKE = 1,209,820,938 J.
Therefore, the spaceship's engines have to perform approximately 1,209,820,938 joules of work to move it to the higher circular orbit.
Let's learn more about circular orbit :
https://brainly.com/question/28106901
#SPJ11
When charging an object by induction, the object to be charged must be a conductor. Why? Must the object causing induction also be a conductor? Why or why not?
The object to be charged by induction must be a conductor because only conductors allow for the free movement of electrons within the material, which is necessary for charge redistribution. When a charged object is brought near a conductor, the excess charge on the charged object induces a redistribution of charges within the conductor.
Electrons within the conductor are able to move easily, redistributing themselves in response to the presence of the charged object.
On the other hand, the object causing induction does not have to be a conductor. It can be either a conductor or an insulator. The key factor is the presence of a charged object that can induce a redistribution of charges within the object being charged. As long as there is a mechanism for charge redistribution, whether it be through the free movement of electrons in a conductor or through the polarization of charges in an insulator, induction can occur.
learn more about "electrons ":- https://brainly.com/question/860094
#SPJ11
A 200g block on a 50-cm long string swings in a circle on a horizontal frictionless table at 75 rpm.
a. draw a free body diagram for the block as viewed from above the table, showing the r-axis and including the net force vector on the diagram
b. write newtons 2nd law equation for the r-axis
c. whats the speed of the block
d. whats the tension in the string
Newton's law equation for the r-axis is F(net) = maᵣ. The speed of the block is 3.93 m/s. The tension in the string is 7.77 N.
a. The free-body diagram is as follows.
b. Newton's second law equation for the r-axis (radial direction) can be written as:
F(net) = maᵣ
Here, Fnet is the net force, m is the mass of the block, and aᵣ is the radial acceleration of the block.
c. The speed of the block:
v = ωr
ω = 75× (2π) (1 / 60) = 7.85 rad/s
The radius of the circular path is given as 50 cm, which is 0.5 m.
v = 7.85 × 0.5 = 3.93 m/s
The speed of the block is 3.93 m/s.
d. To find the tension in the string:
Fnet = T - mg
aᵣ = v² / r
maᵣ = T - mg
m(v² / r) = T - mg
T = m(v² / r) + mg
Substituting the given values:
m = 200 g = 0.2 kg
v = 3.93 m/s
r = 0.5 m
g = 9.8 m/s²
T = (0.2)(3.93)² / 0.5+ (0.2 )(9.8)
T = 7.77 N
Therefore, the tension in the string is 7.77 N.
To know more about the tension in the string:
https://brainly.com/question/32999602
#SPJ4
The tension in the string is approximately 15.4 N. A 200 g block on a 50 cm long string swings in a circle on a horizontal frictionless table at 75 rpm. The solution for the given problem are as follows:
a. A free body diagram for the block as viewed from above the table, showing the r-axis and including the net force vector on the diagram
b. The Newton's 2nd law equation for the r-axis is:m F_net = ma_rHere, F_net is the net force, m is the mass, and a_r is the radial acceleration. Since the block is moving in a circular motion, the net force acting on it must be equal to the centripetal force. So, the above equation becomes:
F_c = ma_rc.
The speed of the block can be calculated as follows:
Given,RPM = 75
The number of revolutions per second = 75/60 = 1.25 rev/s
The time period of revolution, T = 1/1.25 = 0.8 s\
The distance travelled in one revolution, 2πr = 50 cm
So, the speed of the block is given by,v = 2πr/T = 2π(50)/0.8 ≈ 196.35 cmd. The tension in the string can be calculated using the centripetal force formula. We know that,F_c = mv²/rr = 50 cm = 0.5 m
Using the formula, F_c = mv²/rrF_c = (0.2 kg) (196.35 m/s)²/0.5 m = 15397.59 N ≈ 15.4 N
Thus, the tension in the string is approximately 15.4 N.
Learn more about tension from the given link
https://brainly.com/question/30037765
#SPJ11
If an applied force on an object acts antiparallel to the direction of the object's movement, the work done on by the applied force is: Negative Cannot be determined by the problem. Positive Zero
If an applied force on an object acts antiparallel to the direction of the object's movement, the work done by the applied force is negative.
The transfer of energy from one object to another by applying a force to an object, which makes it move in the direction of the force is known as work. When the applied force acts in the opposite direction to the object's movement, the work done by the force is negative.
The formula for work is given by: Work = force x distance x cosθ where,θ is the angle between the applied force and the direction of movement. If the angle between force and movement is 180° (antiparallel), then cosθ = -1 and work done will be negative. Therefore, if an applied force on an object acts antiparallel to the direction of the object's movement, the work done by the applied force is negative.
Learn more about work done here:
https://brainly.com/question/32263955
#SPJ11
CI Photo Credit Cameron Out A 1.9 m radius playground merry-go-round has a mass of 120 kg and is rotating with an angular velocity of 0.400 rev/s. What is its angular velocity after a 22.0 kg child gets onto it by grabbing its outer edge? a The added child is initially at rest. Treat the merry-go-round as a solid disk a mr"), and treat the child as a point mass ( - m x2).
When a 22.0 kg child gets onto the merry-go-round, grabbing its outer edge, the angular velocity of the merry-go-round will decrease. The angular momentum added by the child is L_child = (22.0 kg)(1.9 m)^2 × 0 rev/s.
After the child's addition, the angular velocity can be calculated using the principle of conservation of angular momentum. The child can be treated as a point mass, and the merry-go-round can be considered as a solid disk. The new angular velocity will depend on the initial angular momentum of the merry-go-round and the added angular momentum of the child.
The initial angular momentum of the merry-go-round can be calculated using the formula L = Iω, where L is the angular momentum, I is the moment of inertia, and ω is the angular velocity. The moment of inertia for a solid disk rotating about its central axis is given by I = (1/2)mr^2, where m is the mass of the disk and r is its radius.
Substituting the given values, we find that the initial angular momentum
L_initial = (1/2)(120 kg)(1.9 m)^2 × 0.400 rev/s.
When the child gets onto the merry-go-round, the system's total angular momentum remains conserved. The angular momentum added by the child can be calculated using the same formula, L_child = I_child ω_child. Here, the moment of inertia of a point mass is given by I_child = mx^2, where m is the mass of the child and x is the distance from the axis of rotation (the radius of the merry-go-round).
Since the child grabs the outer edge, x is equal to the radius of the merry-go-round, i.e., x = 1.9 m. Therefore, the angular momentum added by the child is L_child = (22.0 kg)(1.9 m)^2 × 0 rev/s.
Learn more about angular velocity click here: brainly.com/question/32217742
#SPJ11