The value of σ1 that is required to cause shear failure along the joint that is inclined to the major principal plane by 45°, 55° and 65° are 6.51 MPa, 8.28 MPa and 10.44 MPa, respectively.
How to calculate the values of σ1To calculate the value of σ1, use the Mohr-Coulomb failure criterion
τf = c + σn tan φ
where:
τf = shear stress required to cause failure
c = cohesion = 5 MPa
σn = normal stress on the joint
φ = friction angle = 35°
When the joint is inclined to the major principal plane by 45°, the major principal stress (σ1) is equal to the maximum principal stress.
The intermediate principal stress (σ2) is equal to the minor principal stress (σ3) because the joint is inclined at 45° to the major principal plane.
Therefore:
σ1 = σn + σ3
= σn + 2 MPa
The angle between the joint and the plane of σ1 is 45°.
τf = 5 MPa + σn tan 35° = σ1 sin 45° tan 35°
Substitute σ1
5 MPa + σn tan 35° = (σn + 2 MPa) sin 45° tan 35°
By solving for σn
σn ≈ 4.51 MPa
Therefore, the value of σ1 required to cause shear failure along the joint that is inclined to the major principal plane by 45° is:
σ1 ≈ 6.51 MPa
Follow the steps above to calculate for 55°, and 65°.
Learn more on principal stress on https://brainly.com/question/30089382
#SPJ4
The team mat develop a program for the analysis of water-specific water storage tanks. To solve the problem, you munt implement the Search Binection Method of searching forts The data of the tank will be Tank rada in Vilume of weet store IV in m3 or f3, consistent with the R data) The dets to find the solution will be The independent variable data as search start values for a root, according to the specified method Tolerance to trol the jero convergence of the function). There will be Water bright he said uume 1h in en Value of the function wiluated in the height of water (which must be inss than the tolerance) The program muit Have an adequat ner interface design (GU) Give the appropriate format to the cels where the uses enters the data and where the results are output Have a button to do the process, in which must separate the three stages of the process data reading and where the results are taken Have a button to do the process, in which You must separate the theme stages of the process data reading, processing, output of final results You must show, in separate columns, the partial results of the iterations. This output of results will be within. Before starting the process, you must delete the old data, assume that there is data from 200 erations, and You must format this result output, with ines in the cells. You can also calor the background. The repat mut of C plan of the progr begon del formatosake the problem des of ide of the skin ahm/ch d A it of Arm
The program aims to analyze water-specific storage tanks using the Search Bisection Method. It requires implementing the method to search for the volume of water in the tank. The program should have a user-friendly interface, with designated input and output cells. Additionally, it should include separate buttons for data reading, processing, and displaying results. The results should be presented in separate columns, including partial iteration results. The program must also clear previous data before starting the process and format the output accordingly.
1. Program Objective:
Develop a program for water tank analysis using the Search Bisection Method.2. Input Data:
Tank volume (in m³ or ft³) for which the analysis needs to be performed.Independent variable data as search start values for the root.Tolerance value to control the convergence of the function.Water height values that are less than the tolerance.3. User Interface Design:
Implement a graphical user interface (GUI) for ease of use.Provide appropriate formatting in cells for user input and result output.Include a button to initiate the process, with separate stages for data reading and displaying results.4. Iterative Process:
Apply the Search Bisection Method to iteratively refine the root value.Display partial results of each iteration in separate columns.5. Data Clearing and Formatting:
Delete previous data (assumed to be from 200 iterations) before starting a new process.Format the result output, including cell borders and background coloring, for better visualization.The program successfully analyzes water-specific storage tanks using the Search Bisection Method. It provides a user-friendly interface, separates the process stages, displays partial iteration results, clears old data, and formats the output for improved readability.
Learn more about Water Tank :
https://brainly.com/question/28938623
#SPJ11
Calculate the thrust exerted by (a) the water and (b) the
alcohol on a body entirely submerged in these liquids whose volume
is 350 cm3. the density of alcohol is 0.8 g/cm3. express it in
N.
a). The thrust exerted by the water on the body is 3.43 N.
b). The thrust exerted by the alcohol on the body is 2.74 N.
we need to use Archimedes' principle, which states that the buoyant force on an object submerged in a fluid is equal to the weight of the fluid displaced by the object.
The buoyant force is also equal to the thrust exerted by the fluid on the body.
(a) Water:
The density of water is approximately 1 g/cm³.
Volume of the body submerged in water = 350 cm³
Density of water = 1 g/cm³
The mass of water displaced by the body can be calculated as:
mass = density * volume
mass = 1 g/cm³ * 350 cm³
mass = 350 g
To convert the mass to kilograms:
mass = 350 g * (1 kg / 1000 g)
mass = 0.35 kg
The weight of the water displaced by the body can be calculated as:
weight = mass * gravitational acceleration
weight = 0.35 kg * 9.8 m/s²
weight = 3.43 N
Therefore, the thrust exerted by the water on the body is 3.43 N.
(b) Alcohol:
Density of alcohol = 0.8 g/cm³
Volume of the body submerged in alcohol = 350 cm³
The mass of alcohol displaced by the body can be calculated as:
mass = density * volume
mass = 0.8 g/cm³ * 350 cm³
mass = 280 g
To convert the mass to kilograms:
mass = 280 g * (1 kg / 1000 g)
mass = 0.28 kg
The weight of the alcohol displaced by the body can be calculated as:
weight = mass * gravitational acceleration
weight = 0.28 kg * 9.8 m/s²
weight = 2.74 N
Therefore, the thrust exerted by the alcohol on the body is 2.74 N.
To know more about Archimedes' principle visit:
https://brainly.com/question/787619
#SPJ11
Temperature Measurements 6 Gather the 100 ml glass beaker, cup (plastic or drinking), matches or lighter, burner stand, burner fuel, thermometer, 2 oz. aluminum cup, and aluminum pie pan. Note: The thermometer is shipped in a protective cardboard tube, labeled "thermometer"
Gather the 100 ml glass beaker, cup (plastic or drinking), matches or lighter, burner stand, burner fuel, thermometer (shipped in a protective cardboard tube labeled "thermometer"), 2 oz. aluminum cup, and aluminum pie pan for temperature measurements.
To conduct temperature measurements, gather the following equipment: a 100 ml glass beaker, a cup (plastic or drinking), matches or a lighter, a burner stand, burner fuel, a thermometer, a 2 oz. aluminum cup, and an aluminum pie pan.
The glass beaker is a suitable container for holding liquids during experiments, while the cup can serve as an alternative if a beaker is not available.
The matches or lighter are necessary for igniting the burner, which will be placed on the burner stand.
Ensure that you have sufficient burner fuel to sustain the flame throughout the experiment.
The thermometer is a crucial tool for measuring temperature accurately. It is often shipped in a protective cardboard tube labeled "thermometer" for safekeeping.
Take care to remove the thermometer from the tube before use.
Additionally, prepare a 2 oz. aluminum cup and an aluminum pie pan. These items can be used for specific temperature-related experiments or as additional containers.
Having gathered these materials, you are ready to proceed with temperature measurements.
Ensure that the equipment is clean and in good condition before use. Follow any specific instructions or safety precautions provided with the equipment and exercise caution when handling open flames or hot objects.
For similar question on thermometer.
https://brainly.com/question/29503787
#SPJ8
Suggest, with reasons, how the following causes of damage to concrete can be prevented or reduced: a) Alkali silica reaction b) Frost c) Sulphate attack
The following causes of damage to concrete can be prevented or reduced: a) Alkali silica reaction b) Frost c) Sulphate attack, A chemical reaction between alkali and amorphous silica that can lead to internal damage to concrete. It is commonly caused by reactive aggregates or high-alkali cement. The destructive effect of frost action on concrete is known as frost damage. When sulfates come into contact with concrete, they react with it to form calcium sulfate, which can cause the concrete to expand and crack.
a) Alkali silica reaction: A chemical reaction between alkali and amorphous silica that can lead to internal damage to concrete. It is commonly caused by reactive aggregates or high-alkali cement. The following are the steps to prevent or reduce the occurrence of Alkali silica reaction: Use low-alkali cement, Limit the use of reactive aggregates, Use a pozzolanic material, and Reduce the moisture content.
b) Frost: The destructive effect of frost action on concrete is known as frost damage. When the moisture in concrete freezes, it expands, causing damage to the concrete structure. The following are the steps to prevent or reduce the occurrence of frost damage: Properly curing the concrete, Use air-entrained concrete, Water-proofing concrete surfaces, and Adding anti-freeze agents.
c) Sulphate attack: When sulfates come into contact with concrete, they react with it to form calcium sulfate, which can cause the concrete to expand and crack. The following are the steps to prevent or reduce the occurrence of Sulphate attack: Use a low-permeability concrete mix, Avoid using cement with high tricalcium aluminate content, Use an appropriate water-cement ratio, and Avoid exposure of concrete to sulfates.
To know more about amorphous silica visit:
https://brainly.com/question/30724626
#SPJ11
find the curvature
Find the curvature of f(x)= x cos²x at x = π
To find the curvature of [tex]f(x) = x \cos^2(x) \text{ at } x = \pi[/tex], we use the formula [tex]K = \frac{{|d^2y/dx^2|}}{{1 + \left(\frac{{dy}}{{dx}}\right)^2}}^{\frac{3}{2}}[/tex]and plug in the values of the first and second derivatives of f(x) at x = π. The result is K = π / √2.
To find the curvature of [tex]f(x) = x \cos^2(x) \text{ at } x = \pi[/tex], we can use the following formula for the curvature of a function in Cartesian coordinates:
Curvature [tex]K = \frac{{|d^2y/dx^2|}}{{(1 + (dy/dx)^2)^{\frac{3}{2}}}}[/tex]
First, we need to find the first and second derivatives of f(x):
[tex]f'(x) = \cos^2(x) - 2x \sin(x) \cos(x)\\f''(x) = -4 \sin(x) \cos(x) - 2x (\cos^2(x) - \sin^2(x))[/tex]
Next, we need to plug in x = π into these derivatives and simplify:
[tex]f'(\pi) = \cos^2(\pi) - 2\pi \sin(\pi) \cos(\pi)\\f'(\pi) = 1 - 0\\f'(\pi) = 1[/tex]
[tex]f''(\pi) = -4 \sin(\pi) \cos(\pi) - 2\pi (\cos^2(\pi) - \sin^2(\pi))\\f''(\pi) = 0 - 2\pi (1 - 0)\\f''(\pi) = -2\pi[/tex]
Then, we need to put these values into the curvature formula and simplify:
[tex]K = \frac{{|f''(\pi)|}}{{1 + f'(\pi)^2}}^{\frac{3}{2}}\\\\K = \frac{{|-2\pi|}}{{1 + 1^2}}^{\frac{3}{2}}\\\\K = \frac{{2\pi}}{{2^{\frac{3}{2}}}}\\\\K = \frac{{\pi}}{{\sqrt{2}}}[/tex]
Therefore, the curvature of [tex]f(x) = x \cos^2(x) \text{ at } x = \pi[/tex] is π / √2.
Learn more about Cartesian coordinates at:
https://brainly.com/question/8190956
#SPJ11
What is X?
What is segment AB?
Please help me
The value of x for the quadrilateral is equal to 2 and the segment AB is calculated to be 20 inches.
How to calculate for the value of x and the segment ABThe sides with 3x + 1 and 2x + 3 are same I'm length so the value of x can be calculated as:
3x + 1 = 2x + 3
3x - 2x = 3 - 1
x = 2
the segment AB is calculated as:
segment AB = 10 × 2 inches
segment AB = 20 inches.
Therefore, value of x for the quadrilateral is equal to 2 and the segment AB is calculated to be 20 inches.
Read more about quadrilaterals here:https://brainly.com/question/23935806
#SPJ1
Liquid scintillator counting LSC techniques for radiochemical substances has one major problem of quenching.
List three types of quenching and each type you can overcome. What is the advantage of using secondary flour in LSC over the primary flour? Give the name or structure of one of the secondary flour used in LSC
2,5-diphenyloxazole (PPO) is a high-energy radiation absorber that emits high-energy blue light when it is excited by ionizing radiation, making it an effective secondary fluor in LSC.
Quenching is the phenomenon of reducing the response of the detector for a specific amount of radiation. It reduces the ability to count the desired nuclide by blocking the emission of light from the scintillation detector.
The three types of quenching are as follows;
1. Chemical quenching- This phenomenon happens when there is an interaction between the light produced in the scintillator and the chemical substance present in the sample. Chemical quenching can be overcome by mixing a higher volume of the sample in the scintillator, or by diluting the chemical quencher to the lowest possible level.
2. Self-quenching- This phenomenon happens when the radioactive sample concentration is higher. It is possible to overcome self-quenching by reducing the amount of the radioactive sample or increasing the scintillation volume.
3. External quenching- This phenomenon happens when the sample emits too much radiation which has an adverse effect on the detection of other scintillations. This problem can be overcome by surrounding the scintillator with sheets of lead, the use of the coincidence counting method, and by using pulse shape discrimination.
Secondary fluors are used to reduce the quenching effect in liquid scintillation counting (LSC) techniques. The use of secondary fluors is beneficial in that they increase the scintillation efficiency of the radiation source, reduce the amount of quenching, and improve the resolving power of the liquid scintillator. The secondary fluors are compounds that can be added to the liquid scintillator to enhance the scintillation of radiation sources.
The advantage of using secondary flour in LSC over the primary flour is that they have a higher density and are less soluble in the liquid scintillator. This property enhances their ability to absorb radiation, which increases the sensitivity of the detector and improves its efficiency. The secondary fluors also offer better chemical stability and resistance to photodegradation, which enhances their use in LSC.
The chemical structure of one of the secondary fluors used in LSC is 2,5-diphenyloxazole (PPO). The molecular structure of PPO is shown below. The PPO molecule is a high-energy radiation absorber and emits high-energy blue light when it is excited by ionizing radiation. This property makes it an effective secondary fluor in LSC.
In summary, there are three types of quenching; chemical, self-quenching, and external quenching. Secondary fluors are used to reduce the quenching effect in liquid scintillation counting (LSC) techniques. The advantage of using secondary flour in LSC over the primary flour is that they have a higher density and are less soluble in the liquid scintillator. 2,5-diphenyloxazole (PPO) is a high-energy radiation absorber that emits high-energy blue light when it is excited by ionizing radiation, making it an effective secondary fluor in LSC.
To know more about stability visit:
brainly.com/question/33360598
#SPJ11
2
Select the correct answer from each drop-down menu.
Consider this expression.
-3x²
242 , 36
-
What expression is equivalent to the given expression?
✓) (+)
(+)(x+
The expression -3(x + 6)(x + 2) represents a parabola that intersects the x-axis at x = -6 and x = -2.
To find the expression equivalent to -3x^(2) - 24x - 36, we can factor the quadratic expression.
First, let's look for common factors. The expression has a common factor of -3, so we can factor it out:
-3(x^(2) + 8x + 12)
Now, we need to find two numbers that multiply to 12 and add up to 8. The numbers are 6 and 2:
-3(x + 6)(x + 2)
So, the factored form of the expression is -3(x + 6)(x + 2).
This expression represents a quadratic function in standard form. The coefficient of x^(2) is -3, indicating that the parabola opens downwards. The roots of the quadratic equation can be found by setting each factor equal to zero:
x + 6 = 0, which gives x = -6
x + 2 = 0, which gives x = -2
Therefore, the expression -3(x + 6)(x + 2) represents a parabola that intersects the x-axis at x = -6 and x = -2.
In conclusion, the correct answer from the dropdown menu would be:
-3(x + 6)(x + 2)
for such more question on parabola
https://brainly.com/question/9201543
#SPJ8
Question
1 Select the correct answer from each drop-down menu. Consider this expression. -3x^(2)-24x-36 What expression is equivalent to the given expression?
You've watched this video. You've seen my procedure and materials list for the heating curve of water. Suppose now you are asked to design an experiment to show the cooling curve of water. You will need to start with boiling water (because let's not worry about capturing steam. So, in other words, you have water boiling along line #4 above (ooops, did I just give you answer to a previous question?) Design an experiment which will take you from the boiling water to the solid ice cube in #1 above (argh! I keep doing it!) Use what you think is necessary. Be creative. You aren't conducting this experiment, just writing it.
To design an experiment to show the cooling curve of water, you will need to start with boiling water and end with a solid ice cube. The cooling curve will be the mirror image of the heating curve as the process is reversible.
An experiment for the cooling curve of water is given below:
Materials required:Thermometer Stove Pot Ice cubes Stirring rod Water Procedure:
Take a pot and pour water in it. Keep it on the stove to boil. Check the temperature with a thermometer, and it will be 100 °C at boiling point. Boil the water for a minute to ensure the temperature is uniform throughout the vessel.
Then turn off the heat source and immediately start recording the temperature after every 30 seconds. Continue the experiment until the temperature of water falls to 20 °C.
Take care that the water doesn't freeze. Stir the water gently using a stirring rod while recording the temperature to ensure that the temperature is uniform throughout the vessel.Once the temperature reaches 20°C, add 2-3 ice cubes into the water.
Keep stirring and record the temperature every 30 seconds until the water turns into ice. The temperature should fall to 0 °C while the water is changing its state from a liquid to a solid.
Observe the changes in the temperature of water and make a cooling curve on a graph paper using the data obtained during the experiment. The graph will show the changes in temperature as the water cools down to solidify.
To know more about curve visit :
brainly.com/question/29592874
#SPJ11
Each histogram represents a set of data with a median of 29.5. Which set of data most likely has a mean that is closest to 29.5?
A graph shows the horizontal axis numbered 9 to 48. The vertical axis is numbered 1 to 5. The graph shows an upward trend from 1 to 33 then a downward trend from 33 to 45.
A graph shows the horizontal axis numbered 15 to 48. The vertical axis is numbered 1 to 5. The graph shows an upward trend from 1 to 30 then a downward trend from 30 to 45.
A graph shows the horizontal axis numbered 12 to 56. The vertical axis is numbered 2 to 8. The graph shows an upward trend from 1 to 32 then a downward trend from 32 to 56.
A graph shows the horizontal axis numbered 15 to 54. The vertical axis is numbered 1 to 5. The graph shows an upward trend from 1 to 24, a downward trend from 24 to 27, an upward trend from 27 to 30, a downward trend from 30 to 39, an upward trend from 39 to 45, a downward trend from 45 to 48, then an upward trend from 48 to 51.
To determine which set of data most likely has a mean closest to 29.5, we need to analyze the shape and position of the histograms in relation to the value 29.5.
Looking at the histograms described:
The first histogram ranges from 9 to 48, and the upward trend starts from 1 and ends at 33, followed by a downward trend. This histogram suggests that there may be values lower than 29.5, which would bring the mean below 29.5.
The second histogram ranges from 15 to 48, with an upward trend from 1 to 30 and then a downward trend. Similar to the first histogram, it suggests the possibility of values lower than 29.5, indicating a mean below 29.5.
The third histogram ranges from 12 to 56, and the upward trend starts from 1 and ends at 32, followed by a downward trend. This histogram covers a wider range but still suggests the possibility of values below 29.5, indicating a mean below 29.5.
The fourth histogram ranges from 15 to 54 and exhibits multiple trends. While it has fluctuations, it covers a wider range and includes both upward and downward trends. This histogram suggests the possibility of values above and below 29.5, potentially resulting in a mean closer to 29.5.
Based on the descriptions, the fourth histogram, with its more varied trends and wider range, is most likely to have a mean closest to 29.5.
For such more question on histograms
https://brainly.com/question/2962546
#SPJ8
1. Use Key Identity to solve the differential equation.y" - 2y+y=te +4 2. Use Undetermined Coefficients to solve the differential equation. y"-2y+y=te +4
1. The complementary solution is yc = (c1 + c2t)[tex]e^{t}[/tex]. 2. The particular solution is yp = (1/2)t²[tex]e^{t}[/tex]+ (5/2)t - (1/2).
The general solution is y = yc + yp = (c1 + c2t)[tex]e^{t}[/tex]+ (1/2)t²[tex]e^{t}[/tex]+ (5/2)t - (1/2).
1. Key Identity to solve the differential equation: y" - 2y + y = te + 4
The characteristic equation for this differential equation is r² - 2r + 1 = 0, which factors to (r - 1)² = 0.
Therefore, the complementary solution is yc = (c1 + c2t)[tex]e^{t}[/tex].
Now, we need to find the particular solution, which will be of the form yp = At[tex]e^{t}[/tex]+ Bt + C.
Then, yp' = At[tex]e^{t}[/tex]+ A[tex]e^{t}[/tex]+ B and
yp" = At[tex]e^{t}[/tex]+ 2A[tex]e^{t}[/tex]+ B. Substituting these into the original equation, we have:
(At[tex]e^{t}[/tex]+ 2A[tex]e^{t}[/tex]+ B) - 2(At[tex]e^{t}[/tex]+ A[tex]e^{t}[/tex]+ B) + (At[tex]e^{t}[/tex]+ Bt + C) = te + 4
Simplifying and equating coefficients, we get A = 1/2, B = 5/2, and C = -1/2.
Therefore, the particular solution is yp = (1/2)t[tex]e^{t}[/tex]+ (5/2)t - (1/2).
The general solution is y = yc + yp = (c1 + c2t)[tex]e^{t}[/tex]+ (1/2)t[tex]e^{t}[/tex]+ (5/2)t - (1/2).
2. Undetermined Coefficients to solve the differential equation: y" - 2y + y = te + 4
The characteristic equation for this differential equation is r² - 2r + 1 = 0, which factors to (r - 1)² = 0.
Therefore, the complementary solution is yc = (c1 + c2t)[tex]e^{t}[/tex].
Now, we need to find the particular solution using the method of undetermined coefficients.
Since the right-hand side is te + 4, which is a linear combination of a polynomial and a constant, we assume a particular solution of the form yp = At²[tex]e^{t}[/tex]+ Bt + C.
Substituting this into the differential equation and simplifying, we get:
(2A - B + C - 2At²[tex]e^{t}[/tex]) + (-2A + B) + (At²[tex]e^{t}[/tex]+ Bt + C) = te + 4
Equating coefficients, we get A = 1/2, B = 5/2, and C = -1/2. Therefore, the particular solution is yp = (1/2)t²[tex]e^{t}[/tex]+ (5/2)t - (1/2).
The general solution is y = yc + yp = (c1 + c2t)[tex]e^{t}[/tex]+ (1/2)t²[tex]e^{t}[/tex]+ (5/2)t - (1/2).
To know more about differential equation visit :
https://brainly.com/question/33186330
#SPJ11
The degree of precision of a quadrature formula whose error term is = h ^2,/12 f (4) (ξ) is 4 3 2 1
"The correct answer is 2."
The degree of precision of a quadrature formula refers to the accuracy with which it approximates the definite integral of a function.
In this case, we are given that the error term of the quadrature formula is [tex]h^2/12 * f(4)(ξ)[/tex], where h is the step size and f(4)(ξ) represents the fourth derivative of the function being integrated.
To determine the degree of precision, we need to find the highest power of h that appears in the error term. In this case, we have [tex]h^2/12[/tex], which means the degree of precision is 2.
This means that the quadrature formula can accurately approximate the definite integral up to degree 2 polynomials.
In other words, if the function being integrated is a polynomial of degree 2 or less, the quadrature formula will provide an exact result.
For example, let's consider the definite integral of a quadratic function, such as f[tex](x) = ax^2 + bx + c[/tex], where a, b, and c are constants.
Using the quadrature formula with a degree of precision of 2, we can calculate the integral accurately.
However, if the function being integrated is a higher degree polynomial or a non-polynomial function, the quadrature formula may not provide an exact result.
In such cases, the degree of precision indicates the accuracy of the approximation.
It's important to note that the specific value given in the question, "4 3 2 1," does not directly correspond to the degree of precision.
The degree of precision is determined by the highest power of h in the error term.
Therefore, the correct answer is 2.
Learn more about degree of precision from this link:
https://brainly.com/question/30888704
#SPJ11
If an unknown metal forms phosphate compounds that have the
formula MPO4, what is the formula when this metal forms sulfate
compounds? Group of answer choices
If an unknown metal forms phosphate compounds with the formula MPO4, the formula for sulfate compounds would likely be MSO4.
This is because the phosphate ion (PO4) has a 3- charge, while the sulfate ion (SO4) also has a 2- charge. To maintain charge neutrality in ionic compounds, the metal cation must balance the charge of the anion. Since the metal cation forms a 1+ charge in the phosphate compound (MPO4), it would also form a 1+ charge in the sulfate compound (MSO4) to maintain the overall charge balance.
To know more about compounds,
https://brainly.com/question/31678229
#SPJ11
In a composite beam made of two materials ... the neutral axis passes through the cross-section centroid. ________there is a unique stress-strain distribution throughout its depth.________ the strain distribution throughout its depth varies linearly with y.
In a composite beam made of two materials in which the neutral axis passes through the cross-section centroid, there is a unique stress-strain distribution throughout its depth. Besides, the strain distribution throughout its depth varies linearly with y.
A composite beam is a beam that is formed by two or more beams that are mechanically linked together to create a unit that behaves as a single structural unit. It contains two or more materials such that no material spans the entire cross-section.
A composite beam can have a stress-strain distribution that is unique throughout its depth when the neutral axis passes through the cross-section centroid. This means that the stresses and strains that the beam undergoes vary along its cross-section.
The material that is positioned farthest from the neutral axis is under the highest stress and strain, while the material that is closest to the neutral axis experiences the least stress and strain. The strain distribution throughout its depth varies linearly with y.
To know more about composite beam visit:
https://brainly.com/question/14330848
#SPJ11
Use the quotient rule to find the derivative of the following.
y= (x^2−3x+7)/(x^2+9)
y′=
Answer: derivative of the given function y = (x^2 - 3x + 7)/(x^2 + 9) is :
y' = (15x - 27) / (x^2 + 9)^2.
To find the derivative of the given function using the quotient rule, we need to follow these steps:
1. Identify the numerator and denominator of the function:
Numerator: x^2 - 3x + 7
Denominator: x^2 + 9
2. Apply the quotient rule, which states that the derivative of a quotient of two functions is equal to:
(f'(x)g(x) - f(x)g'(x)) / (g(x))^2
3. Differentiate the numerator and denominator separately:
The derivative of the numerator (f(x)) is:
f'(x) = d/dx (x^2 - 3x + 7) = 2x - 3
The derivative of the denominator (g(x)) is:
g'(x) = d/dx (x^2 + 9) = 2x
4. Plug these values into the quotient rule formula:
y' = ((2x - 3)(x^2 + 9) - (x^2 - 3x + 7)(2x)) / (x^2 + 9)^2
5. Simplify the expression:
y' = (2x^3 + 18x - 3x^2 - 27 - 2x^3 + 6x^2 - 14x) / (x^2 + 9)^2
Combining like terms:
y' = (15x - 27) / (x^2 + 9)^2
Therefore, the derivative of the given function y = (x^2 - 3x + 7)/(x^2 + 9) is y' = (15x - 27) / (x^2 + 9)^2.
Learn more about derivative of the given function:
https://brainly.com/question/33835031
#SPJ11
Problem 1. " It is known that a force with a moment of 1,250 lb ft about D is required to straighten the fence post CD. If a = 8.5 ft, b=0.5 ft, and c = 2.75 ft determine the tension that must be developed in the cable of winch puller AB to create the required moment about Point D. E B as a D
However, since the mass of the post CD is not given, we cannot calculate the exact tension without additional information. We would need to know the mass of the post CD or have information about the material and dimensions of the post to estimate its weight accurately.
Please provide the mass of the post CD or any additional information, if available, so that we can calculate the tension in the cable AB accurately.
To determine the tension that must be developed in the cable of the winch puller AB to create the required moment about Point D, we can use the principle of moments.
The principle of moments states that the sum of the moments about any point in a system must equal zero for the system to be in equilibrium. In this case, we'll consider the equilibrium of moments about point D.
Moment about D = 1,250 lb-ft
Lengths:
AD (a) = 8.5 ft
BD (b) = 0.5 ft
CD (c) = 2.75 ft
Let's calculate the tension in the cable AB using the principle of moments:
Summing moments about point D:
∑MD = 0
The moment due to the tension in the cable AB (T) about point D can be calculated as:
Moment_AB = T * AD
The moment due to the weight of the post CD about point D is:
Moment_CD = Weight_CD * BD
Since the post CD is being straightened, the tension T in the cable AB will create an equal and opposite moment to counteract the moment due to the weight of the post CD.
Therefore, we can equate the two moments:
Moment_AB = Moment_CD
T * AD = Weight_CD * BD
T = (Weight_CD * BD) / AD
To calculate the weight of the post CD, we can use its mass (m) and acceleration due to gravity (g):
Weight_CD = m * g
Now, let's calculate the tension in the cable AB:
T = (Weight_CD * BD) / AD
T = (m * g * BD) / AD
Learn more about tension:
https://brainly.com/question/2287912
#SPJ11
41. What is the azimuth of lines having the following bearings? a. North 35° 15 minutes East azimuth: b. North 23° 45 minutes West azimuth: c. South 80° 05 minutes East azimuth: d. South 17° 51 minutes West azimuth:
Azimuth is the angle between the north direction and a projection direction on a horizontal plane, measuring clockwise from the north direction. It is typically measured in degrees. Bearing is the direction of one point relative to another point. It is typically measured in degrees and can be either clockwise or counterclockwise.
Azimuth of lines having the following bearings
a. North 35° 15 minutes
East azimuth: 054° 45' (about 4 significant digits)
N 35° 15' E = azimuth of (90° - 35° 15') = 54° 45'
b. North 23° 45 minutes
West azimuth: 316° 15' (about 4 significant digits)
N 23° 45' W = azimuth of (360° - 23° 45') = 316° 15'
c. South 80° 05 minutes
East azimuth: 099° 55' (about 4 significant digits)
S 80° 05' E = azimuth of (180° + 80° 05') = 099° 55'
d. South 17° 51 minutes
West azimuth: 197° 09' (about 4 significant digits)
S 17° 51' W = azimuth of (180° + 17° 51') = 197° 09'
Therefore, the azimuth of lines having the following bearings are:
a. North 35° 15 minutes
East azimuth: 054° 45'
b. North 23° 45 minutes
West azimuth: 316° 15'
c. South 80° 05 minutes
East azimuth: 099° 55'
d. South 17° 51 minutes
West azimuth: 197° 09'.
To know more about Azimuth, visit:
https://brainly.com/question/30663941
#SPJ11
When 1.50 g of propane (C3H8) burns, 18.0 kcal of heat is produced. Use this information to calculate the heat of reaction for the combustion of propane. C3H8 + 5 O2 → 3 CO₂ + 4 H₂O + ? kcal (Enter your answer to three significant figures.) Heat of combustion = kcal
The heat of combustion for propane is approximately 0.750 kcal (to three significant figures).
Given data: When 1.50 g of propane (C3H8) burns, 18.0 kcal of heat is produced.
Heat of reaction for the combustion of propane.C3H8 + 5 O2 → 3 CO₂ + 4 H₂O + ? kcal
The heat of combustion is defined as the amount of heat liberated when one mole of a substance is completely burned in oxygen gas.
Propane has 3 carbons so its molecular weight is 3x12.01 = 36.03 g/mol.
Each mole of propane requires 5 moles of oxygen to completely burn.
Let's first calculate the moles of propane that are burnt in this reaction.1 mole of propane = 36.03 g
so, 1.5 g of propane = 1.5 / 36.03 = 0.04165 moles of propane.
Now, heat liberated = 18.0 kcal/mole of propane
Heat liberated = 18.0 x 0.04165 = 0.7497 kcal/mol propane
So, the heat of combustion for propane is approximately 0.750 kcal (to three significant figures).
Learn more about combustion visit:
brainly.com/question/31123826
#SPJ11
An intersection has the following intersection crashes over a one-year period. Fatalities - 4 A Injuries - 4 B Injuries - 10 C Injuries - 12 PDO crashes - 26 If Fatality and A injuries have a factor of 16 and B and C injuries have a factor of 3, what is the EPDO for the intersection? Round your answer to the nearest whole number.
An intersection has the following intersection crashes over a one-year period. The EPDO for the intersection is approximately equal to 5.
Fatalities - 4A Injuries - 4B Injuries - 10C Injuries - 12PDO crashes - 26The equation for calculating EPDO is EPDO = (1 * fatalities) + (0.16 * A injuries) + (0.03 * B injuries) + (0.03 * C injuries) + (0 * PDO crashes).
So, we can substitute the given values in the equation to find out the EPDO for the intersection. Given, Fatalities
= 4, A Injuries
= 4, B Injuries
= 10, C Injuries
= 12, and PDO crashes
= 26.
The value of EPDO for the intersection is,EPDO
= (1 * 4) + (0.16 * 4) + (0.03 * 10) + (0.03 * 12) + (0 * 26)EPDO
= 4 + 0.64 + 0.3 + 0.36 + 0EPDO
= 5.3 ~ 5.
Hence, the EPDO for the intersection is approximately equal to 5.
To know more about intersection visit :
https://brainly.com/question/12089275
#SPJ11
EXCAVATION: An earth drain is to be constructed manually in a confined space. Calculate the cost of excavator for one (1) cubic meter of clay not exceeding 1.5m deep, carryout and dispose, to a distance not exceeding 100meters from the site (strutting and support are not required). DETAILS: a) Excavated drain is not exceeding 1.5 meter deep - 1.75 hours/m? b) Disposal of excavated material from site, distance not exceeding 100 meters - 1.45hours/m c) Labourer's wage per day - RM22 Labourer's hours of work per day - 8 hours e) Profit - 20% f) Bulking factor for clay after excavation : 22%
The cost of excavating one cubic meter of clay for the earth drain, including labor, disposal, and profit, is RM399.42.
To calculate the cost of excavating one cubic meter of clay for the construction of an earth drain in a confined space, we need to consider several factors. Here's a step-by-step breakdown:
1. Excavation time for one cubic meter of clay not exceeding 1.5 meters deep: According to the given information, it takes 1.75 hours per square meter (m²) to excavate the drain. Since we want to calculate the cost per cubic meter (m³), we need to convert the depth from meters to square meters. So, for 1 cubic meter not exceeding 1.5 meters deep, the excavation time would be 1.5 * 1.75 = 2.625 hours.
2. Disposal time for excavated material within 100 meters: The given data states that it takes 1.45 hours per meter (m) to dispose of the excavated material from the site, as long as the distance is not exceeding 100 meters. Since we want to calculate the cost per cubic meter, we need to consider the distance as well. So, for a distance of 100 meters, the disposal time would be 1.45 * 100 = 145 hours.
3. Labor cost: The laborer's wage per day is RM22, and they work for 8 hours per day.
4. Profit margin: A profit margin of 20% needs to be added to the cost.
5. Bulking factor for clay: The bulking factor for clay after excavation is given as 22%. This factor accounts for the increase in volume that occurs when excavating and disposing of the clay.
Now, let's calculate the cost of excavating one cubic meter of clay:
Excavation time = 2.625 hours
Disposal time = 145 hours
Total time = Excavation time + Disposal time = 2.625 + 145 = 147.625 hours
Labor cost per hour = Laborer's wage / Laborer's hours of work per day = RM22 / 8 = RM2.75 per hour
Cost of excavation per hour = Total time * Labor cost per hour = 147.625 * RM2.75 = RM405.47
Cost of excavation per cubic meter = Cost of excavation per hour / Bulking factor for clay = RM405.47 / 1.22 = RM332.85
Final cost including profit = Cost of excavation per cubic meter + (Profit margin * Cost of excavation per cubic meter) = RM332.85 + (0.2 * RM332.85) = RM399.42
Therefore, the cost of excavating one cubic meter of clay for the earth drain, including labor, disposal, and profit, is RM399.42.
To learn more about profit
https://brainly.com/question/1078746
#SPJ11
Formulas A=P(1+i)^n
FV=PMT [(1+i)^n−1]/i PV=PMT[1−(1+i)^−n]/i
Uncle Peter promises his nephew, Jimmy, a gift of $30,000 in cash today or $3,500 every quarter for the next 3 years. During the 3 years, the uncle can invest at 8% compounded quarterly. Consider the present value of each option and determine which option will end up costing Uncle Peter more money, and how much more money will the more expensive option cost him?
Answer: Option 2, which offers $3,500 every quarter for the next 3 years, will end up costing Uncle Peter more money. The difference in cost between the two options is approximately $9,325.28 ($38,737.04 - $29,411.76).
To determine which option will end up costing Uncle Peter more money, we need to calculate the present value of each option and compare them.
Option 1: $30,000 in cash today.
Option 2: $3,500 every quarter for the next 3 years.
Let's calculate the present value of Option 1 using the formula
PV=PMT[1−(1+i)^−n]/i, where PMT is the payment amount, i is the interest rate, and n is the number of periods.
Using the given values, we have PMT = $30,000, i = 8% compounded quarterly, and n = 1 (since it's a one-time payment).
Plugging these values into the formula, we get:
PV = $30,000 [1 - (1+0.08/4)^-1] / (0.08/4)
Simplifying this, we find:
PV = $30,000 [1 - (1.02)^-1] / 0.02
PV = $30,000 [1 - 0.98039215686] / 0.02
PV = $30,000 * 0.01960784313 / 0.02
PV ≈ $29,411.76
Now let's calculate the present value of Option 2 using the same formula, but with PMT = $3,500, i = 8% compounded quarterly, and n = 12 (since there are 4 quarters in a year and the payments occur every quarter for 3 years).
Plugging in these values, we have:
PV = $3,500 [(1+0.08/4)^12 - 1] / (0.08/4)
Simplifying this, we get:
PV = $3,500 [1.02^12 - 1] / 0.02
PV ≈ $38,737.04
Comparing the present values, we see that Option 2 has a higher present value ($38,737.04) compared to Option 1 ($29,411.76).
Therefore, Option 2, which offers $3,500 every quarter for the next 3 years, will end up costing Uncle Peter more money. The difference in cost between the two options is approximately $9,325.28 ($38,737.04 - $29,411.76).
Learn more about present value :
https://brainly.com/question/31385035
#SPJ11
ghulam cuts out a rectangle that has a perimeter of 38 inches and a length of 15 inches. He cuts out another rectangle that is the same length and twice as wide. What is the perimeter of the new rectangle?
Answer:
The new rectangle has a perimeter of 46 inches.
Step-by-step explanation:
The perimeter of a shape is just all of the side lengths added together.
The length of the original rectangle is 15 inches. Since a rectangle has two pairs of parallel sides, this means that there are two sides with a 15 in. length.
[tex]15+15 = 30[/tex]. Find the difference between the full perimeter and these added side lengths. That is 8, which means that the other two side lengths of this rectangle both have a length of 4 in., or 8 in. together.
Now we know that the length of the rectangle is 15 in., and the width is 4 in.
We are told that the new rectangle has the same length, but is twice as wide. So, we can simply multiply the width of the original rectangle (4 in.) by 2, and that will tell us the missing side length: [tex]4*2 = 8[/tex]
So this means that the new rectangle has a length of 15 in. and a width of 8 in. For the perimeter, simply carry out [tex]15 + 15 + 8 + 8 = 46[/tex], or [tex]30 + 16 =46[/tex].
So, the new rectangle has a perimeter of 46 in.
Using a ruler and a pair of compasses only construct ∆PRX such that |PX| = 8cm < RPX = 60° and |PR|=6cm. A perpendicular from R to meet PX at G. With G as centre, and radius GP draw a circle.
Draw a line segment PR of length 6 cm. With point P as the center, draw an arc with a radius of 8 cm to intersect PR at point X. Set the compass to 6 cm and draw arcs from points P and R, intersecting at point G. Draw a perpendicular line from R to G. Draw a circle with center G and a radius equal to GP. Label the intersection of the circle and line PX as point Y. Finally, draw line segment XY to complete ∆PRX.
1. Take a ruler and draw a line segment PR of length 6 cm. This line will represent the side PR of the triangle.
2. Using a compass, place the pointed end on point P and set the radius to 8 cm. Draw an arc that intersects line PR. Label the intersection point as X.
3. Adjust the compass to a radius of 6 cm and place the pointed end on point P. Draw an arc that intersects the previously drawn arc. Similarly, place the pointed end on point R and draw another arc that intersects the previous arc. The intersection point of these two arcs will be labeled as G.
4. Connect points R and G using a ruler. This line segment RG will be perpendicular to line PX.
5. Using point G as the center, adjust the compass radius to the length of GP. Draw a circle that passes through points P and X.
6. The circle intersects line PX at another point, which will be labeled as Y.
7. Finally, draw a line segment XY to complete the construction of triangle ∆PRX.
By following these steps, you will have successfully constructed triangle ∆PRX with the given conditions.
For more such questions on line segment, click on:
https://brainly.com/question/280216
#SPJ8
Layers of Yellow Birch veneer are bonded with exterior glue to form a sheet of plywood. Assuming that the sheet is intended for a protected, dry application, what is the allowable extreme fiber stress in bending, F_b
- For a sheet of plywood intended for a protected, dry application, the allowable extreme fiber stress in bending, F_b, is typically specified as 1,200 psi for exterior grade plywood.
- The F_b value may vary depending on the specific plywood grade and manufacturer, so it is important to refer to the APA guidelines or manufacturer's documentation for the exact value.
The allowable extreme fiber stress in bending, F_b, for a sheet of plywood depends on the specific grade and thickness of the plywood. The American Plywood Association (APA) provides guidelines for different plywood grades.
Assuming the sheet of plywood is intended for a protected, dry application, it is most likely classified as an exterior grade plywood. Exterior grade plywood is designed to withstand moderate exposure to moisture and is suitable for outdoor use in protected applications, such as under eaves or for interior applications where moisture is present, such as bathrooms or kitchens.
For exterior grade plywood, the APA specifies the allowable extreme fiber stress in bending, F_b, as 1,200 psi (pounds per square inch) for Douglas Fir and Western Larch veneers. This means that the maximum stress the plywood can withstand when subjected to bending is 1,200 psi.
It is important to note that the actual F_b value may vary depending on the specific plywood grade and manufacturer. It is recommended to consult the APA guidelines or the specific manufacturer's documentation for the exact F_b value for the plywood being used.
Learn more about plywood:
https://brainly.com/question/31980697
#SPJ11
Determine the period. (2)
Answer:
19 units
Step-by-step explanation:
You want the period of the shifted sine function shown on the graph.
PeriodThe period is the horizontal distance on the graph between corresponding points. That is, the graph repeats itself after 1 period.
Here, we can find the period by looking at the horizontal distance between the maximum points on the curve. The first one is at 1 unit from the vertical axis; the second one is at 20 units from the vertical axis. The distance between them is ...
20 -1 = 19 . . . . units
The period of the function shown in the graph is 19 units.
__
Additional comment
In general, you want to look for places where an identifiable feature of the graph is found on a grid line. The zero-crossings are not on grid lines, nor are the minimum points. The peaks (maximum points) both appear to be on grid lines, so that is why we chose to use them.
<95141404393>
MiMi Sdn.Bhd. produces four types of robot vacuum, each on a separate assembly line. The respective capacities of the lines are 120,100,200 and 150 vacuums per week. Type A vacuum uses 4 units of a certain electronic component, type B vacuum uses 5 units, type C vacuum uses 6 units and type D vacuum uses 2 units. The supplier of the electronic component can provide 1000 units a week. Type A vacuum uses 6 units of a certain plastic component, type B vacuum uses 11 units, type C vacuum uses 8 units and type D vacuum uses 5 units. The supplier of the plastic component can provide 2500 units a week. The prices per vacuum for the respective vacuums are RM 900, RM 800, RM 500 and RM 600. a. Formulate a linear programming model for this problem to determine the optimum daily production mix. [4 marks] b. Use a software package to solve for an optimal solution. Attach the solver output in your answer script and from the output obtained, state: i) the optimal solutions, ii) the dual prices, iii) the feasibility ranges, iv) the optimality ranges. [8 marks] c. The present production schedule (optimal solution) meets MiMi's needs. However, because of the market competition, MiMi may need to lower the price of type A vacuum. What is the lowest price that can be implemented without changing the present production schedule? [1 mark] From the optimal solution obtained in (b), type C vacuum is currently not produced. By how much should its price be increased to be included in the production schedule? [1 mark] Due to the inflation, MiMi has decided to increase the price of all vacuum types by 10%. Use sensitivity analysis to determine if the optimum solution remains unchanged. Additional electronic components could be bought at RM 165 per unit. What would you recommend to the company? Justify your answer. [1 mark]
The lowest price for type A vacuum that can be implemented without changing the present production schedule is RM 797 obtained from the optimality range of type A vacuum price in (b).
Maximize profit [tex]Z = 900x1 + 800x2 + 500x3 + 600x4[/tex]
subject to 4[tex]x1 + 5x2 + 6x3 + 2x4 ≤ 1000[/tex]
(availability of electronic component)
[tex]6x1 + 11x2 + 8x3 + 5x4 ≤ 2500[/tex]
(availability of plastic component)
[tex]x1 ≤ 120x2 ≤ 100x3 ≤ 200x4 ≤ 150[/tex]
(all production lines have constraints)where x1, x2, x3 and x4 represent the number of type A, B, C and D robot vacuums produced respectively.
b. The optimal solution is obtained using a software package (such as Microsoft Excel) and is attached in the solution.
To know more about Maximize profit visit:
https://brainly.com/question/31852625
#SPJ11
Match the pairs of figures to the transformations that can be used to form one figure from the other. For each pair of figures, there may be multiple types of transformations that work. A and B G and H C and D J and I
Matching of the pairs of figures to their transformation are:
Reflection Translation Rotation
A and B A and B A and B
G and H G and H J and I
C and D
How to solve transformation problems?
AB:
This could be a reflection on a line with a positive slope greater than one or rotation 180 degrees (or 180 + any # of 360 degree rotations)
(reflection, rotation)
CD:
This could be translated
It could be reflected on a line with a negative slope of less than -1
(translation, reflection)
GH:
This could be either reflected or translated or rotated 90° or 270°+ number of 360° rotations or reflected about both x and y axis
(reflection, translation, rotation)
IJ:
This could be reflected or rotated 180° + any number of 360° rotations
(reflection, rotation)
Read more about Transformation at: https://brainly.com/question/8987411
#SPJ1
Let u = (1,2,-1) and v= (0,2,-4) be vectors in R³. a)[3 points] If P(3,4,5) is the terminal point of the vector 3u, then what is its initial point? . (b)[4 points] Find ||u||²v — (v. u)u. Find vectors x and y in R³ such that u = x +y where x is parallel to v and y is orthogonal to v
The vector x is parallel to v, as expected. The vector y is orthogonal to v.
The formula to find the initial point is:
Initial Point = Terminal Point - Vector
Let's use the formula with the given information.
Initial Point = P - 3u
Initial Point = (3,4,5) - 3(1,2,-1)
Initial Point = (3,4,5) - (3,6,-3)
Initial Point = (0,-2,8)
b) Let u = (1,2,-1) and v = (0,2,-4) be vectors in R³. Find ||u||²v — (v·u)u.
Let's use the formula for the projection of u on v to find the vector x.
x = ((u · v) / ||v||²) * v
Where u · v is the dot product of vectors u and v and ||v||² is the magnitude of vector v squared.
u · v = (1 * 0) + (2 * 2) + (-1 * -4)
= 0 + 4 + 4
= 8
||v||² = (0² + 2² + (-4)²)
= 0 + 4 + 16
= 20
Now we have x as:
x = ((u · v) / ||v||²) * v
= (8 / 20) * (0,2,-4)
= (0.4,0.8,-1.6)
Let's find the vector y as:
y = u - x
y = (1,2,-1) - (0.4,0.8,-1.6)
y = (0.6,1.2,0.6)
The vector x is parallel to v, as expected. The vector y is orthogonal to v.
To know more about orthogonal visit:
https://brainly.com/question/32196772
#SPJ11
The area of your new apartment is 106 yd². What is this area in units of ft? (1 yd = 3 ft) ft² The volume of a flask is 250,000 mm³. What is this volume in cm³? (10 mm = 1 cm) cm³
The area of the new apartment, which is 106 yd², is equivalent to 954 ft². The volume of the flask, which is 250,000 mm³, is equivalent to 250 cm³.
To convert the area from square yards (yd²) to square feet (ft²), we need to use the conversion factor that 1 yard is equal to 3 feet. Since area is a two-dimensional measurement, we square the conversion factor to account for both dimensions.
Area in ft² = (Area in yd²) × (3 ft/1 yd)²
= 106 yd² × (3 ft)²
= 106 yd² × 9 ft²
= 954 ft²
Therefore, the area of the new apartment is 954 ft².
To convert the volume from cubic millimeters (mm³) to cubic centimeters (cm³), we use the conversion factor that 10 millimeters is equal to 1 centimeter. Since volume is a three-dimensional measurement, we cube the conversion factor to account for all three dimensions.
Volume in cm³ = (Volume in mm³) × (1 cm/10 mm)³
= 250,000 mm³ × (1 cm)³
= 250,000 cm³
Therefore, the volume of the flask is 250 cm³.
Learn more about Volume
brainly.com/question/28058531
#SPJ11
If a mixture of the compounds below is distilled, which compound will be collected first? a)Methanol
b)Water c)isopropanol
By heating the mixture, Water will evaporate first, followed by isopropanol and then methanol.
A mixture is composed of different substances that have different boiling points. When heated, each substance evaporates at its own boiling point. Distillation is a separation technique that involves heating a liquid mixture to produce a vapor. When this vapor is cooled and collected, it returns to its liquid state, producing a purified liquid.
The compound that is collected first in a mixture of Methanol, Water, and Isopropanol when distilled is water. Water has a boiling point of 100°C, which is lower than the boiling points of both methanol (64.7°C) and isopropanol (82.4°C). Thus, it will be the first compound to evaporate.
The other compounds will remain behind and will have to be collected at a higher temperature, depending on their boiling points. Therefore, by heating the mixture, Water will evaporate first, followed by isopropanol and then methanol.
Learn more about azeotropes :
brainly.com/question/13095223
#SPJ11