Rotational dynamics is the study of forces and motions about an axis of rotation.
Explanation:Formulas such as Kinematic Equations and Newton's laws can be expressed in rotating coordinate frames such as: Newton's 2nd Law Fnet=m x a translates into Torque = I x α Where I is Moment of Inertia (the rotational analogous term to mass)
Answer:
Rotational dynamics is the study of forces and motions about an axis of rotation.
Explanation:
Formulas such as Kinematic Equations and Newton's laws can be expressed in rotating coordinate frames such as:
Newton's 2nd Law Fnet=m x a translates into Torque =I x α Where I is Moment of Inertia (the rotational analogous term to mass)
and α is angular acceleration.
Density of water is-
Answer:
The density of water is around 997 kg/m³ of 1 gran per millilimeter
how do astronomers determine the origin of a meteorite that reaches earth?
Researchers begin their study by identifying the rock type and then dating the meteorite
Explanation:
.
Can you please draw circuit diagram with 5 Ω resistor in series with bulb, switch and 12 V battery?
Answer:
Sorry for the bad drawing, as you have not specified whether is should be open switch or close I have drawn both
I hope it helps.
A plane flying above the ground has 60,000 joules of kinetic energy and 6,000 joules off gravitational potential energy. How much mechanical energy does the plane have?
Answer:
66,000J
Explanation:
Mechanical energy = Gravitational energy + Kinetic Energy
ME = 6,000 + 60,000 = 66000 J
what is the average power supplied by a 60.0 kg person running up a flight of stairs a vertical distance of 4.0 in 4.2s
Hi there!
We know that:
[tex]P = \frac{W}{t}\\\\[/tex]
Where:
W = Work done (J)
t = time (s)
We can calculate the work using the equation:
[tex]W = \Delta U = mg\Delta h[/tex]
Plug in the given values:
[tex]W = 60(9.8)(4) = 2352J[/tex]
Now, divide by time:
[tex]P = \frac{W}{t} = \frac{2352}{4.2} = \boxed{560W \text{ (Watts)}}[/tex]
An amateur astronomer has just discovered a dwarf planet in an orbit past Pluto. Choose the best unit of measure to describe how far out in the solar system it is from the Sun.
The weight of a 1,000 kg car is ______________ (pick best answer)
Group of answer choices
9800 N
102.4 N
1000 N
10000 N
What is the weight of a car with the mass of 1000 kg?
Answer: it is 9800 N.
13. A ball is dropped. According to Newton's Third Law, the action force is the
earth pulling the ball, and the reaction is:
Answer:
the ground when the ball hits it
Explanation:
A ball falls freely towards the Earth. If the action force is the Earth pulling down on the ball, then identify which of the following best describe the reaction force:
why does the energy of characteristic x rays tend to increase for heavier elements?
The energy of characteristic x rays tend to increase for heavier elements
because the charge of the nucleus increases.
X ray is a form of an electromagnetic spectrum and the energy is directly
proportional to the charge of the nucleus. This implies that an increase in
the nucleus charge will lead to a corresponding increase in x ray energy
and vice versa.
X rays energy is also usually more in heavier elements than when
compared to lighter elements
Read more on https://brainly.com/question/9376695
Cho mạch điện gồm ba điện trở mắc nối tiếp nhau. Biết R 1 = 8Ω, R 2 = 12Ω, R 3 = 4Ω. Hiệu điện thế giữa hai đầu đoạn mạch U = 48V. Tính hiệu điện thế giữa hai đầu mỗi điện trở.
56gq2391$/= 343568
hope u understand me
Please slove this i need answer fast
Answer:
I am not quite sure....
Explanation:
Explanation:
basically i, say the answer is w
A concave mirror has a centre of curvature of 24.0 cm. An object 2.5 cm tall is placed 40.0 cm in front of the mirror.
a) At what distance from the mirror will the image be formed?
b) What is the height of the image?
Answer:
Object distance should be 48
Explanation:
in pic
_____________________________
(hope this helps can I pls have brainlist (crown)☺️)
What is the acceleration of a 20 kg backpack lifted with a force of 15 N?
a. 0.75 m/s2
b. 1.33 m/s2
c. 300 m/s2
d. 5 m/s2
The answer is option A. 0.75 m/s^2
the formula needed to solve this is acceleration = force/mass
we know the following:
mass of the backpack = 20KG
the force is 15N
therefor- acceleration = 15/20
which can also be written as 3/4, leaving us with the final answer of .75 m/s^2
Answer:
0.75 m/s2
Explanation:
0.75 m/s2
How do you solve problems involving acceleration
Answer:
Velocity/time =acceleration
Acceleration x time = velocity
Velocity/acceleration=time
What is the approximate value of log⁵³ 217895.4
Answer:
3.09594
Explanation:
hope this helps
A force acts on an object. Which option describes an action that could prevent the object from moving
Answer:
Friction or tension
Explanation:
Friction stops an object from moving in the presence of force
Managers use information systems to help them make decisions that will improve their businesses. What three levels of information do managers need to make these decisions? Provide one example of how information systems can provide this data.
The main categories of information systems include management-level system, operational-level system, and strategic-level system.
Information system simply means the integrated set of components that are vital for the collection, storage, and processing of data to make organizational decisions.
Information systems can be used at operational level in order to provide data that can support operational activities by keeping track of the transactions of the company.
Read related link on:
https://brainly.com/question/25682948
What are some simple machines that decrease mechanical advantage used to do? increase work decrease work multiply distance to increase speed.
Answer:
Wheel and axleForce multipliersLeverInclined planePulleyScrewWedgeExplanation:
Simple machines are devices with no, or very few, moving parts that make work easier. Many of today's complex tools are just combinations or more complicated forms of the six simple machines, according to the University of Colorado at Boulder. For instance, we might attach a long handle to a shaft to make a windlass, or use a block and tackle to pull a load up a ramp. While these machines may seem simple, they continue to provide us with the means to do many things that we could never do without them.
Have a great day! :D
Some machines decrease mechanical advantage and are utilized to multiply distance to decrease speed.
What is the mechanical advantage?Mechanical advantage can be described as a measure of the ratio of output force to input force in a system. Mechanical advantage is used to analyze the forces in simple machines such as levers and pulleys.
Mechanical Advantage= output force (load) /input force(effort)
The mechanical advantage will increase as the slope of the inclined plane decreases but the load has to move with more distance. Under the mechanical advantage, the distance the load will move will be a fraction of the distance through applied force.
Thus, the mechanical advantage is decreased by some simple Machines decrease and are used to multiply distance to decrease speed.
Learn more about Mechanical advantages, here:
brainly.com/question/16617083
#SPJ2
A camper stands in a valley between two parallel cliff walls. He claps his hands and notices that the echo from the nearby wall returns 0.9 s later while the echo from the farther wall returns 1.10 s later. If the air temperature is -10 C, how wide is the valley?
test questions!!!!!!!!
Answer:
B. surface wave
where does most star formation occur in the milky way galaxy?
Answer:
Star formation occurs most rapidly in the spiral arms, where the density of interstellar matter is highest.
Một oto đang chuyển động thẳng đều với vận tốc 36km/h thì hãm phanh sau 20s thì ô tô dừng lại quãng đường oto đi được là
How can speed be defined
A) acceleration
B) change in velocity/time
C) distance / time
D) displacement/time
Answer:
Speed can be defined in (C) distance / time.
I hope this helped at all.
Which state of matter has molecules that barely move at all?
liquid
gas
solid
They are all the same.
Answer:
the answer is solid.
Explanation:
solid particles have a definite volume and shape therefore they cannot move are they are whole. the particles of solid are closely packed together, barely move, and barely vibrate.
a person with a mass of 15 kg is walking downhill at a velocity of 10 ms what is the Walkers momentum
Answer:
[tex]150 kg\cdot m/s[/tex]
Explanation:
Same as if he was walking uphill, or horizontally. Momentum is defined as the product of mass times velocity. [tex]p = mv = 15\cdot 10 = 150 kg\cdot m/s[/tex]
A system releases 622 kJ of heat and does 105 kJ of work on the surroundings. What is the change in internal energy of the system
Answer:
Δ-727 or -7.27x10²kJ
Explanation:
ΔV=q-w
(q)= -622
(w)= -105
(both negative because it indicate loss of energy)
ΔV= -622+(-105)
ΔV= -727 kJ
The change in internal energy of the system when it released a heat of 622 kJ and does a work of 105 kJ on the surroundings is -727 kJ.
What is change in internal energy?Internal energy is all the energy contained in an object.
To calculate the change in internal energy of the system, we use the formula below.
Formula:
ΔU = Q-W............. Equation 1Where:
ΔU = Change in internal energy of the system,W = work done by the systemQ = Heat released by the system.From the question,
Given:
Q = - 622 kJ ( released of heat)W = 105 kJ.Substitute these values into equation 1
ΔU = -622-105ΔU = -727 kJHence, the change in internal energy of the system when it released a heat of 622 kJ and does a work of 105 kJ on the surroundings is -727 kJ.
Learn more about internal energy here: https://brainly.com/question/25737117
anybody know the answer??
Answer:
Centimeter
Explanation:
We know the measurement is defined as:
1 meter= 100cm
1 cm= 1/100 meter
1 centimeter= 0.01 meter
Therefore, 0.01 meter is equal to 1 cm or 1 centimeter.
i have science map and i dont know what ro answer please help me asap
Answer:
C
Explanation:
The correct answer is C because it puts equivalent measurements in the equivalent cup size. Both cups in answer C are the same measurement: 200 mL. The water in both cups is also the same measurement: 100 mL of 70 degrees Celsius. This is important because equivalent measurements for everything mean the experiment will be fair, equal, and accurate. If the measurements were not equal to each other, your experiment would not be as accurate.
A ball is dropped from a 20.0 m high tower.
a. How long will it take the ball to reach the ground?
b. What is the velocity of the ball just before it hits the ground?
Hi there!
We can begin by using the derived kinematic equation:
[tex]t = \sqrt{\frac{2h}{g}[/tex]
Plug in the given values and let g = 9.8 m/s²:
[tex]t = \sqrt{\frac{2(20)}{g}} = \boxed{2.02 s}[/tex]
Now, we can solve for its final velocity using the equation:
[tex]v_f = v_i + at[/tex]
It is dropped from rest, so vi = 0 m/s.
[tex]v_f = at[/tex]
[tex]v_f = 9.8(2.02) = \boxed{19.796 m/s}[/tex]
Answer:
a. The ball would reach the ground in approximately [tex]2.02\; \rm s[/tex].
b. The velocity of the ball right before landing would be approximately [tex]19.8\; \rm m\cdot s^{-1}[/tex].
(Assumptions: the ball was dropped with no initial velocity; air resistance on the ball is negligible; [tex]g = 9.81\; \rm m\cdot s^{-2}[/tex].)
Explanation:
Under these assumptions, the acceleration of this ball would be constantly [tex]a = g = 9.81\; \rm m\cdot s^{-2}[/tex] (same as the gravitational field strength) during the descent.
Displacement of the ball: [tex]x = 20.0\; \rm m[/tex].
Initial velocity of the ball: [tex]v_{0} = 0\; \rm m\cdot s^{-1}[/tex].
Let [tex]t[/tex] denote the duration of this descent.
The SUVAT equation [tex]x = (1/2)\, a\, t^{2} + v_{0}\, t[/tex] relates the known quantities [tex]a[/tex], [tex]x[/tex], and [tex]v_{0}[/tex] to the unknown [tex]t[/tex].
Substitute the known quantities into this equation and solve to find the value of [tex]t\![/tex]:
[tex]\displaystyle 20.0\; {\rm m} = \frac{1}{2}\times 9.81\; {\rm m\cdot s^{-2}} \times t^{2} + 0\; {\rm m \cdot s^{-1}} \times t[/tex].
[tex]\displaystyle 20.0\; {\rm m} = \frac{1}{2}\times 9.81\; {\rm m\cdot s^{-2}} \times t^{2}[/tex].
[tex]\displaystyle t^{2} = \frac{20.0\; \rm m}{(1/2) \times 9.81\; \rm m\cdot s^{-2}}[/tex].
Since [tex]t > 0[/tex]:
[tex]\begin{aligned}t &= \sqrt{\frac{20.0\; \rm m}{(1/2) \times 9.81\; \rm m\cdot s^{-2}}} \\ &\approx 2.01928\; \rm s\\ &\approx 2.02\; \rm s \\ & (\text{Rounded to 2 sig. fig.})\end{aligned}[/tex].
Since the acceleration of this ball is constant, the velocity of the ball right before landing would be:
[tex]\begin{aligned}v_{1} &= a\, t \\ &\approx 9.81\; \rm m\cdot s^{-2} \times 2.01928\; \rm s \\ &\approx 19.8\; \rm m \cdot s^{-1} \end{aligned}[/tex].
what is cleaning agent
Answer:
Cleaning agents or hard-surface cleaners are substances used to remove dirt, including dust, stains, bad smells, and clutter on surfaces. Purposes of cleaning agents include health, beauty, removing offensive odor, and avoiding the spread of dirt and contaminants to oneself and others.
Answer:
Cleaning agents are substances created for the purpose of cleaning surfaces from germs dirt fungus diseases etcetera.
Explanation: