Answers
Related Questions
1-Name two factors that affect the resilience of wood joints. 2-Name two factors that affect the embedding strength of a timber member. 3-Explain the meaning of the coefficient kmod 4-What is the difference between homogeneous and combined glued laminated timber? With combined glued laminated timber, should the outer or inner lamellas have greater strength? Justify your answer. 5-Describe the relationship between the tensile strength and the angle between the force and grain direction in timber construction using a graph.
Answers
Resilience in wood joints depends on wood type, joint design, and embedding strength of timber members. The coefficient k mod adjusts design values based on moisture content. Homogeneous glued laminated timber has identical strength and stiffness layers, while combined glued laminated timber has different properties. Tensile strength decreases with increasing force and grain direction, as shown in a graph.
1. Two factors that affect the resilience of wood joints are: the type of wood used for the joint the joint design
2. Two factors that affect the embedding strength of a timber member are: the density and moisture content of the timber member the dimensions of the member and the size and number of fasteners used
3. The coefficient k mod is used to adjust the design value of a timber member based on its moisture content. It is the ratio of the strength of a wet timber member to that of a dry timber member.
4. Homogeneous glued laminated timber is made from layers of timber that are identical in strength and stiffness, whereas combined glued laminated timber is made from layers of timber with different properties. In combined glued laminated timber, the outer lamellas have greater strength because they are subject to higher stresses than the inner lamellas.
5. The tensile strength of timber decreases as the angle between the force and grain direction increases. This relationship can be represented by a graph that shows the tensile strength as a function of the angle between the force and grain direction. The graph is a curve that starts at a maximum value when the force is applied parallel to the grain direction, and decreases as the angle increases until it reaches a minimum value when the force is applied perpendicular to the grain direction.
To know more about Resilience Visit:
https://brainly.com/question/31947998
#SPJ11
a) State the differences between normally consolidated and over consolidated clay. A soil in the field at some depth has been subjected to a certain maximum effective past pressure in its geologic history. This maximum effective past pressure may be equal to or less than the existing effective overburden pressure at the time of sampling. The reduction of effective pressure in the field may be caused by natural geologic processes or human processes.
b) Choose ONE (1) suitable foundation type with TWO (2) valid reasons to support. your judgement based on the situation stated. Teguh Jaya Holding is proposing to develop a 20-storey apartment in Cyberjaya, Selangor. This proposed area is underlaid with 15m depth of clayey silts of very high-water table.
Answers
The differences between clay that has been too consolidated and clay that has been usually consolidated are listed below.
What are they?
Normally consolidated clay
Over-consolidated clay
The rate of consolidation is rapid.
The rate of consolidation is slow.
Highest value of void ratio.
Lowest value of void ratio.
More compressible.
Less compressible.
Higher water content and swelling potential.
Lower water content and swelling potential.
Higher permeability.
Lower permeability.
The OCR is equal to 1.
The OCR is greater than 1.
b) A pile foundation would be the most suitable foundation type for the construction of a 20-storey apartment in Cyberjaya, Selangor, underlaid with 15m depth of clayey silts of a very high-water table.
The following are the reasons for this selection of a pile foundation:
Reason 1: Pile foundations are suitable for use in soft soil conditions such as clayey silts. Pile foundations are suitable for soil types with low bearing capacity and high settlement rate.
A pile foundation transfers the load of the structure to a stronger layer beneath the soil, preventing excessive settlement and maintaining stability.
Reason 2: Pile foundations may be installed to reach the required soil depth. Pile foundations are used to transfer load through poor soil to stronger strata beneath the soil.
They are installed by drilling or driving into the ground until they reach a layer of soil or rock with adequate strength.
Since the proposed area has a high-water table, pile foundations are also ideal for use in such conditions because they can be extended through water to the underlying stronger strata.
To know more on soil visit:
https://brainly.com/question/31227835
#SPJ11
Normally consolidated clay has experienced a maximum effective past pressure equal to or less than the existing overburden pressure, while over consolidated clay has experienced a greater past pressure. For an apartment in Cyberjaya with clayey silts and a high water table, a suitable foundation type would be pile foundations due to their ability to handle poor load-bearing capacity and resist the upward pressure from groundwater.
a) Normally consolidated clay and over consolidated clay are two types of clay soils with different characteristics.
Normally consolidated clay refers to clay that has experienced a maximum effective past pressure that is equal to or less than the existing effective overburden pressure at the time of sampling. This means that the clay has undergone natural or human-induced processes that have caused a reduction in effective pressure in the field. As a result, normally consolidated clay tends to have relatively predictable and consistent behavior under loading. When subjected to additional loading, the normally consolidated clay will continue to consolidate and settle gradually over time.
On the other hand, over consolidated clay refers to clay that has experienced a maximum effective past pressure that is greater than the existing effective overburden pressure at the time of sampling. This means that the clay has undergone natural or human-induced processes that have caused the clay to be subjected to higher pressures in the past. As a result, over consolidated clay tends to be more compact and dense compared to normally consolidated clay. It also exhibits higher strength and stiffness due to the previous higher pressures it has experienced.
b) Based on the given situation of developing a 20-storey apartment in Cyberjaya, Selangor, with a 15m depth of clayey silts of very high-water table, a suitable foundation type would be a pile foundation.
Two valid reasons to support this judgment are:
1. Load-bearing capacity: Pile foundations are commonly used in areas with weak or compressible soils, such as clayey silts. By driving piles deep into the ground, the foundation can transfer the load of the structure to a more stable layer of soil or rock below. In this case, the 15m depth of clayey silts suggests the need for a deep foundation to ensure adequate load-bearing capacity.
2. Water table considerations: The presence of a very high-water table indicates the potential for saturated soil conditions. Pile foundations can be designed to withstand the effects of groundwater and minimize settlement caused by water infiltration. By utilizing piles, the foundation can be elevated above the water table, reducing the risk of instability and potential damage to the structure.
Overall, a pile foundation would be a suitable choice for the proposed apartment building in Cyberjaya, Selangor, due to its ability to provide adequate load-bearing capacity and address the challenges posed by the high-water table and clayey silts.
Learn more about consolidated
https://brainly.com/question/28583417
#SPJ11
QUESTION (2) In your own words, discuss the process of undertaking an LCA on two types (solar and hydropower) of renewable energy system. You should mention the key steps involved (goal and scope definition, inventory analysis, allocation, etc.), as well as guidance on how an LCA report should be interpreted. What would be the expected main sources of carbon emissions for such systems and how could the environmental impact be reduced?
Answers
A comprehensive LCA provides valuable insights into the environmental performance of solar and hydropower systems, enabling informed decision-making and the implementation of strategies to mitigate their carbon emissions and environmental impact.
Undertaking a Life Cycle Assessment (LCA) on two types of renewable energy systems, such as solar and hydropower, involves evaluating their environmental impacts throughout their entire life cycle. Here is a discussion of the key steps involved in conducting an LCA and interpreting the LCA report for these systems:
Goal and Scope Definition: The first step is to define the goal and scope of the LCA study. This includes identifying the purpose of the assessment, defining the system boundaries, determining the functional unit (e.g., energy generated), and specifying the life cycle stages to be considered (e.g., raw material extraction, manufacturing, operation, end-of-life).
Inventory Analysis: In this step, data is collected on the inputs (energy, materials, water, etc.) and outputs (emissions, waste, etc.) associated with each life cycle stage of the renewable energy systems. This data is often gathered from various sources, such as literature, industry databases, and specific measurements.
Impact Assessment: The collected inventory data is then analyzed to assess the potential environmental impacts of the systems. Impact categories, such as greenhouse gas emissions, air pollution, water consumption, and land use, are evaluated using impact assessment methods. These methods help quantify and compare the environmental impacts across different categories.
Interpretation: The LCA report should be interpreted with care, considering the specific context and limitations of the study. It is important to understand the boundaries and assumptions made during the assessment. The interpretation should take into account the magnitude and significance of the environmental impacts identified, allowing for informed decision-making and potential improvements.
For solar and hydropower systems, the expected main sources of carbon emissions can vary depending on factors such as the manufacturing processes, material choices, and the energy mix used during construction and operation. Key sources may include the production of solar panels (including energy-intensive manufacturing processes) and the emissions associated with the construction and maintenance of hydropower infrastructure.
To reduce the environmental impact of these systems, several strategies can be considered:
Efficiency Improvements: Enhancing the efficiency of solar panels and hydropower turbines can increase the energy output per unit of input and reduce the overall environmental impact.
Renewable Energy Integration: Using renewable energy sources, such as wind or solar, for manufacturing processes and operation of the systems can minimize reliance on fossil fuel-based energy sources and reduce carbon emissions.
Material Selection: Opting for sustainable and low-carbon materials during the manufacturing of solar panels and hydropower infrastructure can help reduce the embodied carbon and environmental impact.
End-of-Life Management: Implementing proper recycling and disposal methods for decommissioned solar panels and hydropower equipment can minimize waste and promote circular economy principles.
Life Cycle Optimization: Conducting ongoing assessments and optimizations of the systems' life cycles can identify areas for improvement and guide decision-making towards reducing environmental impacts.
To learn more about hydropower
brainly.com/question/22258411
#SPJ11
6-10 Let m, n E Z. Prove by contraposition: If m+ n ≥ 19, then m≥ 10 or n ≥ 10.
Answers
By contraposition, we have proven that if m + n ≥ 19, then m ≥ 10 or n ≥ 10.
To prove the statement "If m + n ≥ 19, then m ≥ 10 or n ≥ 10" by contraposition, we assume the negation of the conclusion and show that it implies the negation of the original statement. The negation of the conclusion "m ≥ 10 or n ≥ 10" is "m < 10 and n < 10." The negation of the original statement "If m + n ≥ 19, then m ≥ 10 or n ≥ 10" is "It is not the case that if m + n ≥ 19, then m ≥ 10 or n ≥ 10."
Let's proceed with the proof:
Assume m < 10 and n < 10. We want to show that if m + n ≥ 19, then m ≥ 10 or n ≥ 10 is false.
Since m < 10, we know that the maximum value m can take is 9. Similarly, since n < 10, the maximum value n can take is 9 as well.
If both m and n are at their maximum value of 9, the sum m + n would be 9 + 9 = 18, which is less than 19. Therefore, if m and n are both less than 10, their sum can never be greater than or equal to 19.
Hence, the negation of the conclusion "m < 10 and n < 10" implies the negation of the original statement "If m + n ≥ 19, then m ≥ 10 or n ≥ 10."
Therefore, by contraposition, we have proven that if m + n ≥ 19, then m ≥ 10 or n ≥ 10.
To know more value click-
http://brainly.com/question/843074
#SPJ11
7.00 moles of N2 molecule contains how many N atoms?
a) 8.44 X 10_26 atom
b)4.00 X 10_24 atom
c) 8.44 X 10_24 atom d) 2.44 X 10_24 atom
Answers
One mole of nitrogen gas (N2) contains 2 moles of nitrogen atoms. Therefore, if we have 7 moles of N2 molecules, we have 7 x 2 = 14 moles of nitrogen atoms.
Since one mole of any element contains 6.022 x 10^23 atoms, 14 moles will contain:
14 x 6.022 x 10^23=8.44 x 10^24N atoms.
Therefore, the appropriate is option C) 8.44 x 10^24 atom.
For this question, we use the mole concept of Avogadro's number. One mole of any substance contains 6.022 x 10^23 atoms, molecules or particles. Hence, if we want to find the number of atoms of nitrogen in 7 moles of nitrogen gas, we must first calculate the number of moles of nitrogen atoms present in it.
To find the number of moles of nitrogen atoms present in 7 moles of N2 molecules, we will use the stoichiometric coefficient.
The stoichiometric coefficient of nitrogen in N2 is 2. Therefore, one mole of nitrogen gas contains 2 moles of nitrogen atoms. As such, we can determine that 7 moles of N2 molecules contain 7 x 2 = 14 moles of nitrogen atoms.
Now that we know the number of moles of nitrogen atoms present, we can calculate the number of atoms present in 14 moles of nitrogen atoms.
By using Avogadro's number, we know that 1 mole of nitrogen atoms contains 6.022 x 10^23 atoms of nitrogen.
Therefore, 14 moles of nitrogen atoms will contain:
[tex]14 x 6.022 x 10^23 = 8.44 x 10^24 N atoms.[/tex]
So option C) [tex]8.44 x 10^24 atom.[/tex]
Thus, 7.00 moles of N2 molecule contains 8.44 X 10^24 N atoms.
To know more about stoichiometric coefficient :
brainly.com/question/32088573
#SPJ11
An air-water vapor mixture has a dry bulb temperature of 35°C and an absolute humidity of 0.025kg water/kg dry air at 1std atm. Find i) Percentage humidity ii) Adiabatic Saturation temperature iii) Saturation humidity at 35°C. iv) Molal absolute humidity v) Partial pressure of water vapor in the sample vi) Dew point vii) Humid volume viii) Humid heat ix) Enthalpy
Answers
The percentage humidity is 51.5%. The adiabatic saturation temperature is 45.5°C. Saturation humidity at 35°C is 0.0485 kg water/kg dry air. The partial pressure of water vapor in the sample is 0.025 atm.
Given that, Dry bulb temperature (Tdb) = 35°C and Absolute humidity (ω) = 0.025 kg water/kg dry air at 1 std atm.
Solution: i) Percentage humidity
Relative humidity (RH) = (Absolute humidity/Saturation humidity) x 100RH
= (0.025/0.0485) x 100RH
= 51.5%
Therefore, the percentage humidity is 51.5%.
ii) Adiabatic saturation temperature
Adiabatic saturation temperature is the temperature attained by the wet bulb thermometer when it is surrounded by the air-water vapor mixture in such a manner that it is no longer cooling. It is the saturation temperature corresponding to the humidity ratio of the moist air. Adabatic saturation temperature is given by
Tsat = 2222/(35.85/(243.04+35)-1)
Tsat = 45.5°C
Therefore, the adiabatic saturation temperature is 45.5°C.
iii) Saturation humidity at 35°C.
The saturation humidity is defined as the maximum amount of water vapor that can be held in the air at a given temperature. It is a measure of the water content in the air at saturation or when the air is holding the maximum amount of moisture possible at a given temperature.
Saturation humidity at 35°C is 0.0485 kg water/kg dry air
iv) Molal absolute humidity
Molal absolute humidity is defined as the number of kilograms of water vapor in 1 kg of dry air, divided by the mass of 1 kg of water.
Molal absolute humidity = (Absolute humidity / (28.97 + 18.015×ω))×1000
Molal absolute humidity = (0.025 / (28.97 + 18.015×0.025))×1000
Molal absolute humidity = 0.710
Therefore, the molal absolute humidity is 0.710 kg/kmol.
v) Partial pressure of water vapor in the sample
Partial pressure of water vapor in the sample is given by
p = ω × P
p = 0.025 × 1 std atm = 0.025 atm
Therefore, the partial pressure of water vapor in the sample is 0.025 atm.
vi) Dew point
Dew point is defined as the temperature at which air becomes saturated with water vapor when cooled at a constant pressure. At this point, the air cannot hold any more moisture in the gaseous form, and some of the water vapor must condense to form liquid water. Dew point can be determined using the following equation:
tdp = (243.04 × (ln(RH/100) + (17.625 × Tdb) / (243.04 + Tdb - 17.625 × Tdb))) / (17.625 - ln(RH/100) - (17.625 × Tdb) / (243.04 + Tdb - 17.625 × Tdb))
tdp = (243.04 × (ln(51.5/100) + (17.625 × 35) / (243.04 + 35 - 17.625 × 35))) / (17.625 - ln(51.5/100) - (17.625 × 35) / (243.04 + 35 - 17.625 × 35))
tdp = 22.4°C
Therefore, the dew point is 22.4°C.
vii) Humid volume
The humid volume is the volume of air occupied by unit mass of dry air and unit mass of water vapor. It is defined as the volume of the mixture of dry air and water vapor per unit mass of dry air.
Vh = (R × (Tdb + 273.15) × (1 + 1.6078×ω)) / (P)
where R is the specific gas constant of air, Tdb is the dry bulb temperature, and P is the atmospheric pressure at the measurement location.
Vh = (0.287 × (35+273.15) × (1+1.6078×0.025)) / (1) = 0.920 m3/kg
Therefore, the humid volume is 0.920 m3/kg.
viii) Humid heat
Humid heat is the amount of heat required to raise the temperature of unit mass of the moist air by one degree at constant moisture content.
q = 1.006 × Tdb + (ω × (2501 + 1.86 × Tdb))
q = 1.006 × 35 + (0.025 × (2501 + 1.86 × 35))
q = 57.1 kJ/kg
Therefore, the humid heat is 57.1 kJ/kg.
ix) Enthalpy
The enthalpy of moist air is defined as the amount of energy required to raise the temperature of the mixture of dry air and water vapor from the reference temperature to the actual temperature at a constant pressure. The reference temperature is typically 0°C, and the enthalpy of moist air at this temperature is zero.
The enthalpy can be calculated as follows:
H = 1.006 × Tdb + (ω × (2501 + 1.86 × Tdb)) + (1.86 × Tdb × ω)
H = 1.006 × 35 + (0.025 × (2501 + 1.86 × 35)) + (1.86 × 35 × 0.025)
H = 67.88 kJ/kg
Therefore, the enthalpy is 67.88 kJ/kg.
Learn more about humidity visit:
brainly.com/question/30672810
#SPJ11
Solve the exponential equation using the method of relating the bases by first rewriting the equation in the form e^u=e^v. ex^2=(e^−x)⋅e^20
X=
(Simplify your answer.)
Answers
The solutions to the exponential equation are x = -5 and x = 4.
To solve the exponential equation using the method of relating the bases, we can rewrite the equation in the form
[tex]e^u = e^v,[/tex] where u and v are expressions involving x.
Given equation: [tex]ex^2 = (e^−x)⋅e^20[/tex]
First, let's rewrite the right side of the equation using the properties of exponents:
[tex]ex^2 = e^(20 - x)[/tex]
Now we can relate the bases by setting the exponents equal to each other:
[tex]x^2 = 20 - x[/tex]
To simplify further, let's bring all the terms to one side of the equation:
[tex]x^2 + x - 20 = 0[/tex]
This is now a quadratic equation. We can solve it by factoring or using the quadratic formula. Let's factor it:
(x + 5)(x - 4) = 0
Setting each factor equal to zero gives us two possible solutions:
x + 5 = 0 or x - 4 = 0
Solving each equation:
x = -5 or x = 4
Learn more about exponential equation:
https://brainly.com/question/11832081
#SPJ11
If the BOD5 of a waste is 210 mg/L and BOD (Lo) is 363 mg/L. The BOD rate constant, k for this waste is nearly: 1) k = 0.188 2) k = 0.211 3) k = 0.218 4) k = 0.173
Answers
The correct option from the given choices is:
3) k = 0.218
The BOD rate constant, k, is a measure of the rate at which the biochemical oxygen demand (BOD) of a waste is consumed. It can be calculated using the BOD5 (BOD after 5 days) and BOD (Lo) (initial BOD) values.
To find the BOD rate constant, we can use the formula:
[tex]k = (ln(BOD (Lo) / BOD5)) / t[/tex]
Where:
- ln refers to the natural logarithm function
- BOD (Lo) is the initial BOD value (363 mg/L)
- BOD5 is the BOD after 5 days value (210 mg/L)
- t is the time in days (which is 5 days in this case)
Now, let's substitute the values into the formula:
k = (ln(363 / 210)) / 5
Calculating the natural logarithm of (363 / 210):
k = (ln(1.7286)) / 5
k ≈ 0.218
Therefore, the BOD rate constant, k, for this waste is approximately 0.218.
So, the correct option from the given choices is:
3) k = 0.218
the BOD rate constant (k) is a measure of the rate at which the biochemical oxygen demand (BOD) of a waste is consumed. In this case, the BOD5 of the waste is 210 mg/L and the initial BOD (BOD (Lo)) is 363 mg/L. To calculate the BOD rate constant, we use the formula k = (ln(BOD (Lo) / BOD5)) / t, where ln refers to the natural logarithm function, BOD (Lo) is the initial BOD value, BOD5 is the BOD after 5 days value, and t is the time in days. Substituting the given values into the formula, we find that k ≈ 0.218. Therefore, the correct option is 3) k = 0.218. The BOD rate constant gives us insight into how quickly the waste's BOD is being consumed, which is important in environmental and wastewater treatment applications.
Learn more about logarithm function from the link:
https://brainly.com/question/13473114
#SPJ11
Use the Laplace transform to solve the following initial value problem: y′′+14y′+98y=δ(t−8)y(0)=0,y′(0)=0 y(t)= (Notation: write u(t−c) for the Heaviside step function uc(t) with step at t=c )
Answers
The Laplace transform of the given initial value problem is Y(s) = (e^(-8s)) / (s^2 + 14s + 98), and the inverse Laplace transform of Y(s) will give us the solution y(t) to the initial value problem.
To solve the given initial value problem using Laplace transforms, we will take the Laplace transform of both sides of the differential equation.
First, let's denote the Laplace transform of a function y(t) as Y(s), where s is the complex variable in the Laplace domain.
Taking the Laplace transform of the differential equation y'' + 14y' + 98y = δ(t-8), we get:
s^2Y(s) - sy(0) - y'(0) + 14(sY(s) - y(0)) + 98Y(s) = e^(-8s)
Since y(0) = 0 and y'(0) = 0, the above equation simplifies to:
s^2Y(s) + 14sY(s) + 98Y(s) = e^(-8s)
Now, let's substitute the initial conditions into the equation:
s^2Y(s) + 14sY(s) + 98Y(s) = e^(-8s)
s^2Y(s) + 14sY(s) + 98Y(s) = e^(-8s)
Factoring out Y(s), we get:
(Y(s))(s^2 + 14s + 98) = e^(-8s)
Dividing both sides by (s^2 + 14s + 98), we have:
Y(s) = (e^(-8s)) / (s^2 + 14s + 98)
Now, we need to take the inverse Laplace transform of Y(s) to obtain the solution y(t). However, the expression (e^(-8s)) / (s^2 + 14s + 98) does not have a simple inverse Laplace transform.
To proceed, we can use partial fraction decomposition or refer to Laplace transform tables to find the inverse transform.
In summary, the Laplace transform of the given initial value problem is Y(s) = (e^(-8s)) / (s^2 + 14s + 98), and the inverse Laplace transform of Y(s) will give us the solution y(t) to the initial value problem.
Learn more about Laplace transform from the given link
https://brainly.com/question/2272409
#SPJ11
What is the maximum tractive effort that can be developed for this rear-wheel drive car: • Weight: 2,750 lb. Wheelbase: 113 inches. Center of gravity: 23.5 inch above the road and 51 inch behind the front axle Use maximum coefficient of adhesion on poor, wet pavement.
Answers
The maximum tractive effort that can be developed for this rear-wheel drive car is 4719.98 lbf (pound force). Tractive effort is the force applied to the wheels of a vehicle to make them move. It is a measure of how much force is needed to move the vehicle.
The formula for tractive effort is given by:T = W × f where T is the tractive effort, W is the weight of the vehicle, and f is the coefficient of adhesion. For a rear-wheel-drive car, the tractive effort is given by:T = (W × g × µr) / rwhere g is the acceleration due to gravity (32.2 ft/s²), µr is the coefficient of rolling resistance, and r is the effective radius of the drive wheel.The coefficient of adhesion on poor, wet pavement is 0.1. The weight of the car is 2,750 lb. The center of gravity is 23.5 inches above the road and 51 inches behind the front axle.
The wheelbase is 113 inches. The effective radius of the drive wheel is given by:r = sqrt((w² / 4) + h²)where w is the wheelbase (113 inches) and h is the height of the center of gravity above the rear axle (23.5 - 51 = -27.5 inches, since it is behind the front axle).Therefore,r = sqrt((113² / 4) + (-27.5)²)
≈ 61.2 inches
The tractive effort is given by:T = (W × g × µr) / r
T = (2750 × 32.2 × 0.1) / 61.2T
≈ 4719.98 lbf
Therefore, the maximum tractive effort that can be developed for this rear-wheel drive car is 4719.98 lbf.
To know more about tractive effort visit:
https://brainly.com/question/30163187
#SPJ11
Solve for mzA. Enter your answer in the box. Round your final answer to the nearest degree.
Answers
The measure of angle A to the nearest degree is 50°
What is trigonometric ratio?The trigonometric functions are real functions which relate an angle of a right-angled triangle to ratios of two side lengths.
sinθ = opp/hyp
cosθ = adj/ hyp
tanθ = opp/adj
Taking reference form angle A,
10cm = AC = adjacent
12cm = BC = opposite
Therefore we are going to use the tan function.
Tan A = 12/10
Tan A = 1.2
A = 50° ( to the nearest degree)
Therefore the measure of A to the nearest degree is 50°
learn more about trigonometric ratio from
https://brainly.com/question/24349828
#SPJ1
Find the volume and surface area of the figure.
Round to the nearest hundredths when
necessary.
Answers
Answer:
Volume: 395.84 Surface Area: 929.86
Step-by-step explanation:
Volume: pie*radius*hieght
pie*(14/2)*18
pie*7*18
pie*126
395.84
Surface Area: 2πrh+2πr2
2*pie*7*18+2*pie*7*2
791.6813+87.96459
929.8558
Which of the following linear hydrocarbons may have a double bond? A) C_6 H_14 B) C_10 H_20 C) C_5 H_8 D) C_12H_22
Answers
The linear hydrocarbon that may have a double bond is option C) C5H8.
To determine which of the given linear hydrocarbons may have a double bond, we need to consider the molecular formula and the number of hydrogen atoms in each molecule.
A) C6H14: This hydrocarbon has 6 carbon atoms and 14 hydrogen atoms. The general formula for an alkane (saturated hydrocarbon) with n carbon atoms is CnH2n+2. By applying this formula, we find that C6H14 corresponds to an alkane.
Since alkanes only have single bonds between carbon atoms, there is no double bond present. Therefore, option A is not the correct answer.
B) C10H20: This hydrocarbon has 10 carbon atoms and 20 hydrogen atoms. Again, applying the general formula for alkanes, we see that C10H20 corresponds to an alkane. Therefore, option B is not the correct answer.
C) C5H8: This hydrocarbon has 5 carbon atoms and 8 hydrogen atoms. The general formula for an alkene (unsaturated hydrocarbon with one double bond) with n carbon atoms is CnH2n. By comparing the molecular formula C5H8 to the formula for alkenes, we see that the ratio matches.
Therefore, option C is a possible linear hydrocarbon that may have a double bond.
D) C12H22: This hydrocarbon has 12 carbon atoms and 22 hydrogen atoms. Applying the general formula for alkanes, we see that C12H22 corresponds to an alkane. Therefore, option D is not the correct answer.
Based on the analysis, the linear hydrocarbon that may have a double bond is C) C5H8.
Learn more about hydrocarbon from the given link
https://brainly.com/question/7509853
#SPJ11
Water flows under the partially opened sluice gate, which is in a rectangular channel. Suppose that yAyAy_A = 8 mm and yByBy_B = 3 mm Find the depth yCyC at the downstream end of the jump.
Answers
The depth yC at the downstream end of the jump is 2.66 mm.
The answer is given below, with a word count of 102 words.
Suppose yA = 8 mm and yB = 3 mm. We need to find the depth yC at the downstream end of the jump.The flow is open-channel and has a jump.
As the depth of the jump changes continuously, we need to use the Bernoulli equation between sections 1 and 2.The Bernoulli equation between sections 1 and 2 is given by:
-y1 + V1²/2g + z1 = -y2 + V2²/2g + z2,
where, y is the depth of the water,V is the velocity of the water,g is the acceleration due to gravity,z is the height above an arbitrarily chosen datum line.
Let us take datum line to be at the free water surface at section 2 i.e. z2 = 0. Also, let us assume that velocity at section 1 and section 2 are same, as they are both open to atmosphere. Thus V1 = V2.
Substituting the values and solving for y2, we get:y2 = 2.66 mm.
Therefore, the depth yC at the downstream end of the jump is 2.66 mm.
Thus, the depth yC at the downstream end of the jump in a rectangular channel where yA = 8 mm and yB = 3 mm is 2.66 mm.
To know more about velocity visit:
brainly.com/question/30559316
#SPJ11
Product inventories have been prepared for two different designs of a high speed widget. The matrices are shown in the following. The data on the left side are about Design 1 , on the right are about Design 2. (1) Based on streamlined LCA (SLCA) analysis of the data (show column score, row score, and final overall score for each design option), select the better product from a DfES viewpoint, (2) What aspects of each design do you need to improve from DfES viewpoint? Support your answer with data and reasons. (3) Illustrate the data in the "Target Plot" chart (one plot for each design option) and submit the completed charts. The blank chart "Streamlined LCA_Pie Chart" is in Blackboard folder "Week 2_July 11-15: Class Learning Materials" Packing=PD, Recycling=RD. Resource extraction=pre-manufacture=PM. Text Table 14.2 and Fig. 14.2, p.196 shows full name of each abbreviation.
Answers
1. Based on streamlined LCA (SLCA) analysis of the data, Design 1 is the better product from a DfES viewpoint. The column score, row score, and final overall score for each design option are shown in the table below:Design Option Column Score Row Score Final Overall Score Design 1.984.925.98 Design 2.933.545.09
2. Aspects of each design that need improvement from a DfES viewpoint are:Design 1: Although Design 1 has a better score than Design 2, it still has room for improvement. The resource extraction stage needs improvement, as it has the highest impact of all stages. The production phase also has a relatively high impact, although it is still lower than the resource extraction stage.
Design 2: Although Design 2 has a lower overall score than Design 1, it still has some strengths. Design 2 has a lower impact in the resource extraction stage, but a higher impact in the production stage. The production stage could be improved by reducing energy and water consumption.3. The Target Plot charts for each design option are attached below:Design 1 Target Plot Design 2 Target Plot
To know more about streamlined visit :
https://brainly.com/question/10193549
#SPJ11
Find the eigenvalues λn and eigenfunctions yn(x) for the equation y′′+λy=0 in each of the following cases: (a) y(0)=0,y(π/2)=0; (b) y(0)=0,y(2π)=0; (c) y(0)=0,y(1)=0; (d) y(0)=0,y(L)=0 when L>0; (e) y(−L)=0,y(L)=0 when L>0; (f) y(a)=0,y(b)=0 when a
Answers
we have y[tex]n= n2π24L2n = 1,3,5,...[/tex]0.
his gives us the following solutions: λ[tex]n= n2π24L2n = 1,3,5,...[/tex]
yn([tex]x) = sin(nπxL), n = 1,3,5,...(f) y(a)=0,y(b)=0[/tex]
For the boundary conditions, we have y(0)=0 and y(π/2)=0. This gives us the following solutions:
λn= n2π2n = 1,2,3,... yn(x)
= sin(nπx2), n = 1,2,3,...(b)
y(0)=0,y(2π)=0
For the boundary conditions, we have y(0)=0 and y(2π)=0.
This gives us the following solutions:λn= n2π2n = 1,2,3,... y[tex]n(x) = sin(nπxπ), n = 1,2,3,...(c) y(0)=0,y(1)=0[/tex]
For the boundary conditions, we have y(0)=0 and y(1)=0.
This gives us the following solutions:λn= n2π2n = 1,2,3,...
yn(x) = sin(nπx), n = 1,3,5,... and
yn(x) = cos(nπx) − cos(nπ),
n = 2,4,6,...(d)
y(0)=0,y(L)=0 when L>0
For the boundary conditions, we have [tex]y(0)=0 and y(L)=0[/tex].
To know more about gives visit:
https://brainly.com/question/29424969
#SPJ11
The type of transport that allows amino acids to move across cell membranes with the use of a protein channel without using chemical energy is called: A) facilitated transport. B) diffusion.
C) active transport. D) train transport E) air transport A- B - C -
D -
E-
Answers
The correct answer is A) facilitated transport. Facilitated transport, also known as facilitated diffusion, is the type of transport that allows amino acids to move across cell membranes with the use of protein channels.
In facilitated transport, specific protein channels or carriers embedded in the cell membrane aid in the movement of molecules or ions across the membrane.
In the case of amino acids, these molecules are polar and cannot easily pass through the nonpolar lipid bilayer of the cell membrane. Therefore, protein channels provide a pathway for amino acids to cross the membrane. These protein channels are selective and allow only specific molecules, such as amino acids, to pass through.
Facilitated transport does not require the expenditure of chemical energy, such as ATP. Instead, it relies on the concentration gradient of the molecules being transported. The movement occurs from an area of higher concentration to an area of lower concentration, following the concentration gradient.
The protein channels used in facilitated transport exhibit specificity and selectivity for certain molecules, including amino acids. These channels have binding sites that recognize and bind to specific amino acids, facilitating their transport across the membrane.
Therefore, the correct answer is A) facilitated transport, which describes the transport of amino acids across cell membranes with the use of protein channels.
Learn more about amino acids:
https://brainly.com/question/14351754
#SPJ11
If g(x)=(x−5)^3 (2x−7m)^4 and x=5 is a root with multiplicity n, what is the value of n?
Answers
If [tex]\displaystyle g( x) =( x-5)^{3}( 2x-7m)^{4}[/tex] and [tex]\displaystyle x=5[/tex] is a root with multiplicity [tex]\displaystyle n[/tex], we can determine the value of [tex]\displaystyle n[/tex] by evaluating [tex]\displaystyle g( x) [/tex] at [tex]\displaystyle x=5[/tex].
Substituting [tex]\displaystyle x=5[/tex] into [tex]\displaystyle g( x) [/tex], we have:
[tex]\displaystyle g( 5) =( 5-5)^{3}( 2( 5)-7m)^{4}[/tex]
Simplifying this expression, we get:
[tex]\displaystyle g( 5) =( 0)^{3}( 10-7m)^{4}[/tex]
[tex]\displaystyle g( 5) =0\cdot ( 10-7m)^{4}[/tex]
[tex]\displaystyle g( 5) =0[/tex]
Since [tex]\displaystyle g( 5) =0[/tex], it means that [tex]\displaystyle x=5[/tex] is a root of [tex]\displaystyle g( x) [/tex]. However, we need to determine the multiplicity of this root, which refers to the number of times it appears.
In this case, the root [tex]\displaystyle x=5[/tex] has a multiplicity of [tex]\displaystyle n[/tex]. Since the function [tex]\displaystyle g( x) [/tex] evaluates to [tex]\displaystyle 0[/tex] at [tex]\displaystyle x=5[/tex], it implies that the root [tex]\displaystyle x=5[/tex] appears [tex]\displaystyle n[/tex] times in the factored form of [tex]\displaystyle g( x) [/tex].
Therefore, the value of [tex]\displaystyle n[/tex] is [tex]\displaystyle 3[/tex] (the multiplicity of the root [tex]\displaystyle x=5[/tex]).
[tex]\huge{\mathfrak{\colorbox{black}{\textcolor{lime}{I\:hope\:this\:helps\:!\:\:}}}}[/tex]
♥️ [tex]\large{\underline{\textcolor{red}{\mathcal{SUMIT\:\:ROY\:\:(:\:\:}}}}[/tex]
4a) Solve each equation.
Answers
Answer:
Subtract 7 from both sides which gives you 2x=12
x=6
A steady, incompressible, two-dimensional velocity field is given by V = (u, v) = (0.5 +0.8x) 7+ (1.5-0.8y)] Calculate the material acceleration at the point (X-3 cm, y=5 cm). Just provide final answers. (1)
Answers
The material acceleration at the point (x = 3 cm,
y = 5 cm) is (2.88, 4.16) cm/s².
Given the velocity field: V = (u, v)
= [(0.5 + 0.8x) 7 + (1.5 - 0.8y)]
To calculate the material acceleration at the point (x = 3 cm,
y = 5 cm) the expression for acceleration is given as:
a = ∂v/∂t + V . ∇V
The equation represents the sum of the acceleration due to change of velocity with time and acceleration due to change in direction of flow. Let's begin with calculating the material acceleration by using the given information.
So, we have:
V = (u, v)
= [(0.5 + 0.8x) 7 + (1.5 - 0.8y)]
On substituting the values of x and y in V, we get
V = (u, v)
= [(0.5 + 0.8 × 3) 7 + (1.5 - 0.8 × 5)]
= (6.1, -2.7)
The time derivative of the velocity field is:
∂v/∂t = (∂u/∂t, ∂v/∂t)
= 0 (since it is given steady)
Now, we calculate the gradient of the velocity field as:
∇V = [(∂u/∂x), (∂v/∂y)]
= [0.8, -0.8]
Therefore, the material acceleration is calculated using the equation:
a = ∂v/∂t + V . ∇V
a = 0 + (6.1, -2.7) . [0.8, -0.8]
= (2.88, 4.16) cm/s²
The material acceleration at the point (x = 3 cm,
y = 5 cm) is (2.88, 4.16) cm/s².
To know more about acceleration visit
https://brainly.com/question/16710160
#SPJ11
Briefly explain why the Ponchon-Savarit method for calculating the theoretical stages in a binary distillation can be more accurate than McCabeThiele method.
Answers
The Ponchon-Savarit method for calculating theoretical stages in a binary distillation can be more accurate than the McCabe-Thiele method because it takes into account the non-ideal behavior of the liquid and vapor phases.
In the Ponchon-Savarit method, the equilibrium curve is represented as a polynomial equation, which allows for a more accurate representation of the separation process. This method also considers the effect of varying reflux ratios on the number of theoretical stages required. By accounting for non-ideal behavior and varying reflux ratios, the Ponchon-Savarit method provides a more accurate estimation of the theoretical stages required for a binary distillation.
On the other hand, the McCabe-Thiele method assumes ideal behavior and constant reflux ratio, which can lead to less accurate results. It represents the equilibrium curve using a straight line, which simplifies the calculations but does not account for non-ideal behavior. Additionally, the McCabe-Thiele method does not consider the effect of varying reflux ratios on the separation process.
In summary, the Ponchon-Savarit method is more accurate than the McCabe-Thiele method in calculating the theoretical stages in a binary distillation because it considers non-ideal behavior and varying reflux ratios.
Know more about Ponchon-Savarit method here:
https://brainly.com/question/33792283
#SPJ11
Calculate the number of grams of NaCN that must be added to 1.0 L of a 0.5M HCN solution to give a pH of 7.0. (Ka for HCN is 6.2 x 10-10)
A. 0.0034g
B. 11g
C. 24g
D. 160g
E. 0.15g
Answers
The number of grams of NaCN that must be added to the solution is approximately 1.52 x 10^(-8) g.
To calculate the number of grams of NaCN that must be added to 1.0 L of a 0.5M HCN solution to give a pH of 7.0, we need to consider the dissociation of HCN and the resulting concentration of CN- ions.
The dissociation of HCN can be represented by the equation: HCN ⇌ H+ + CN-
Since we want to achieve a pH of 7.0, we know that the concentration of H+ ions should be equal to 10^(-7) M. Using the equation for the dissociation constant (Ka) of HCN (6.2 x 10^(-10)), we can determine the concentration of CN- ions.
Ka = [H+][CN-]/[HCN]
By substituting the known values into the equation, we can solve for [CN-]. Rearranging the equation, we have:
[Cn-] = (Ka * [HCN])/[H+]
[Cn-] = (6.2 x 10^(-10) * 0.5) / 10^(-7)
[Cn-] = 3.1 x 10^(-10) M
Now, we can calculate the number of moles of CN- ions present in the 1.0 L solution:
moles = concentration * volume
moles = 3.1 x 10^(-10) * 1.0
moles = 3.1 x 10^(-10) mol
Finally, we can calculate the mass of NaCN required using the molar mass of NaCN (49.01 g/mol):
mass = moles * molar mass
mass = 3.1 x 10^(-10) * 49.01
mass ≈ 1.52 x 10^(-8) g
Therefore, the number of grams of NaCN that must be added to the solution is approximately 1.52 x 10^(-8) g.
Know more about dissociation here:
https://brainly.com/question/32501023
#SPJ11
Help please , 20 points
Answers
If the measure of angle A is 23 degrees, the approximate measure of angle B is 67°.
If CA = 6.5 and BD = 5, then AD = 4.15 units.
What is a supplementary angle?In Mathematics and Geometry, a supplementary angle simply refers to two (2) angles or arc whose sum is equal to 180 degrees.
Additionally, the sum of all of the angles on a straight line is always equal to 180 degrees. In this scenario, we can logically deduce that the sum of the given angles are supplementary angles:
m∠ACB + m∠A + m∠B = 180°
m∠B = 180° - (90 + 23)
m∠B = 67°
Since AB is a diameter (angle D is a right angle), we would apply Pythagorean's theorem to find AD as follows;
AB² = AD² + DB²
AD² = AB² - DB²
AD² = 6.5² - 5²
AD = √17.25
AD = 4.15 units.
Read more on supplementary angle here: brainly.com/question/13250148
#SPJ1
When nickel-63 is converted to copper-63 A) an electron is captured B) a neutron is released C) an alpha particle is emitted D) an electron is released
Answers
The correct answer is A) an electron is captured.
When nickel-63 (Ni-63) is converted to copper-63 (Cu-63), the process involves a nuclear transformation where a neutron in the nickel nucleus is converted into a proton. This conversion is accompanied by the capture of an electron from the electron cloud surrounding the nucleus.
In this process, a neutron in the nickel nucleus is converted to a proton, resulting in a change in atomic number from 28 (nickel) to 29 (copper). Since the number of protons determines the identity of an element, the nucleus is transformed into copper. To maintain charge neutrality, an electron from the electron cloud is captured by the nucleus to balance the increase in positive charge due to the additional proton.
Therefore, the conversion of nickel-63 to copper-63 involves the capture of an electron (option A) to maintain charge balance during the nuclear transformation.
Learn more about electron from the given link:
https://brainly.com/question/12001116
#SPJ11
"
What is the coefficient of x²wa³b in the expansion of (x+y+w+a+b)^7?
Answers
The coefficient of x²wa³b in the expansion of (x+y+w+a+b)⁷ is 420.
To find the coefficient of x²wa³b in the expansion of (x+y+w+a+b)^7, we can use the multinomial theorem.
According to the multinomial theorem, the coefficient of a term in the expansion of (x+y+w+a+b)ⁿ is given by:
Coefficient = n! / (r₁! * r₂! * r₃! * r₄! * r₅!)
Where n is the power to which the binomial is raised (in this case, 7), and r₁, r₂, r₃, r₄, and r₅ are the exponents of x, y, w, a, and b, respectively, in the term we are interested in.
In this case, we want to find the coefficient of the term with x²wa³b.
The exponents of x, y, w, a, and b in this term are 2, 0, 1, 3, and 1, respectively.
Plugging these values into the formula, we have:
Coefficient = 7! / (2! * 0! * 1! * 3! * 1!)
= 5040 / (2 * 1 * 6 * 1)
= 5040 / 12
= 420
Therefore, the coefficient of x²wa³b in the expansion of (x+y+w+a+b)⁷ is 420.
To know more about coefficient, click
https://brainly.com/question/1594145
#SPJ11
The coefficient of [tex]\(x^2wa^3b\)[/tex] in the expansion of [tex]\((x+y+w+a+b)^7\)[/tex] is the numerical value that multiplies the term [tex]\(x^2wa^3b\)[/tex] when the expression is fully expanded. In this case, we need to find the coefficient of this specific term in the binomial expansion.
To calculate the coefficient, we can use the Binomial Theorem. According to the Binomial Theorem, the coefficient of a term in the expansion of [tex]\((x+y+w+a+b)^n\)[/tex] can be found by using the formula:
[tex]\[\binom{n}{r_1, r_2, r_3, r_4, r_5} \cdot x^{r_1} \cdot y^{r_2} \cdot w^{r_3} \cdot a^{r_4} \cdot b^{r_5}\][/tex]
Where [tex]\(\binom{n}{r_1, r_2, r_3, r_4, r_5}\)[/tex] represents the binomial coefficient, which is the number of ways to choose the exponents [tex]\(r_1, r_2, r_3, r_4, r_5\)[/tex] from the powers of [tex]\(x, y, w, a, b\)[/tex] respectively, and n is the exponent of the binomial.
In this case, we want to find the coefficient of [tex]\(x^2wa^3b\)[/tex] in the expansion of [tex]\((x+y+w+a+b)^7\)[/tex]. We can determine the exponents [tex]\(r_1, r_2, r_3, r_4, r_5\)[/tex] that correspond to this term and calculate the binomial coefficient using the formula above.
To learn more about coefficient refer:
https://brainly.com/question/24068089
#SPJ11
What should be the quantity of chlorine required to treat a flow of 3MLD if the chlorine demand is 12mg/L and a chlorine residual of 2mg/L is desired?
Answers
The total amount of chlorine required per day would be 17,820 kg/day.
Therefore, the quantity of chlorine required to treat a flow of 3 MLD if the chlorine demand is 12mg/L and a chlorine residual of 2mg/L is desired is 30kg/day.
To treat a flow of 3 MLD, the quantity of chlorine required, given a chlorine demand of 12mg/L and a chlorine residual of 2mg/L is 30kg/day.Chlorination is a water treatment process that employs chlorine or chlorine-containing compounds to purify water. The most widely used disinfectant for drinking water, chlorine is relatively inexpensive and capable of killing most pathogens that might be present in the water.
How much chlorine is needed to treat water?
The amount of chlorine needed to treat water is determined by the amount of organic and inorganic matter, ammonia, nitrogen, and other substances present in the water that can react with the chlorine and the volume of water to be treated.
The quantity of chlorine that is required is usually measured in mg/L (milligrams per litre) or ppm (parts per million). For example, a chlorine demand of 12mg/L indicates that 12 milligrams of chlorine are required to disinfect 1 litre of water.
So, to calculate the quantity of chlorine needed to treat a flow of 3 MLD, we need to multiply the flow rate (3 MLD) by the chlorine demand (12mg/L) and then by the number of days in the year (365). This will give us the total amount of chlorine needed per year. Then, we divide this amount by 365 to get the amount of chlorine needed per day.Mathematically,Quantity of chlorine required
= Flow rate x Chlorine demand x 365 / 1000 kg/day
= 3 MLD x 12 mg/L x 365 / 1000 kg/day
= 13,140 kg/day
However, this only gives us the amount of chlorine needed to meet the chlorine demand. If we also want to achieve a chlorine residual of 2 mg/L, we need to add the amount of chlorine required to achieve this residual. The amount of chlorine required to achieve a residual can be determined by conducting a jar test or by using empirical data.For instance, let us say that based on empirical data, we need to add 4 mg/L of chlorine to achieve a residual of 2 mg/L. The total amount of chlorine required per day would be 17,820 kg/day.
Therefore, the quantity of chlorine required to treat a flow of 3 MLD if the chlorine demand is 12mg/L and a chlorine residual of 2mg/L is desired is 30kg/day.
To know more about chlorine visit:
https://brainly.com/question/19460448
#SPJ11
Concrete derives its strength by the hydration of cement particles, the hydration of cement is not a momentary action but a process continuing for long time. Curing is the process of controlling the rate and extent of moisture loss from concrete during cement hydration. In details write about the curing of the concrete.
Answers
Curing is a process that involves controlling the rate and extent of moisture loss during cement hydration. It is essential for the development of strength and durability in concrete structures. By maintaining the right moisture content, temperature, and protection against rapid drying, curing allows the concrete to reach its full potential.
The curing of concrete is a crucial process that helps control the rate and extent of moisture loss during cement hydration. This process is important because it ensures that the concrete gains strength and durability over time. The process follows:
1. Immediately after pouring the concrete, it is essential to protect it from drying out too quickly. This can be done by covering it with a plastic sheet or applying a curing compound. By preventing rapid moisture loss, the curing process allows the concrete to hydrate properly and develop its strength.
2. The duration of the curing process is typically around 7 to 28 days, depending on the type of cement used and the desired strength of the concrete. During this time, it is important to keep the concrete moist to support the ongoing hydration process.
3. One common method of curing is to continuously wet the concrete surface by sprinkling it with water or by using moist burlap or mats. This helps maintain the required moisture content for proper hydration.
4. Another method of curing is through the use of curing compounds. These compounds are liquid coatings that are applied to the concrete surface. They form a barrier that prevents moisture from evaporating, thus promoting the proper curing of the concrete.
5. Curing can also be aided by controlling the temperature of the concrete. High temperatures can accelerate the hydration process but can also lead to excessive moisture loss. On the other hand, low temperatures can slow down hydration. Therefore, maintaining an optimal temperature range is important for effective curing.
6. It's worth noting that proper curing is crucial for achieving the desired strength, durability, and resistance to cracking in concrete structures. Insufficient curing can lead to weakened concrete and an increased risk of cracking.
To know more about cement hydration, refer to the link below:
https://brainly.com/question/17275699#
#SPJ11
HELP ME PLS IM BEGGING
Answers
Given c = 10.5, m∠A = 30, and m∠B = 52, we can use the Law of Sines to find b. Rounded to the nearest tenth, b ≈ 8.0.
Given b = 20, a = 26, and m∠A = 65, we can use the Law of Sines to find m∠B. Rounded to the nearest tenth, m∠B ≈ 47.5.
Given a = 125, m∠A = 42, and m∠B = 65, we can use the Law of Sines to find c. Rounded to the nearest tenth, c ≈ 154.3.
Given c = 18.4, m∠B = 35, and m∠C = 52, we can use the Law of Sines to find a. Rounded to the nearest tenth, a ≈ 10.5.
Given a = 12.5, m∠A = 50, and m∠B = 65, we can use the Law of Sines to find b. Rounded to the nearest tenth, b ≈ 15.2.
1)To find the length of side b, we can use the Law of Sines. The formula is:
b/sin(B) = c/sin(C)
Plugging in the given values:
b/sin(52) = 10.5/sin(180 - 30 - 52)
Using the sine addition formula:
b/sin(52) = 10.5/sin(98)
Cross-multiplying:
b * sin(98) = 10.5 * sin(52)
Dividing both sides by sin(98):
b = (10.5 * sin(52)) / sin(98)
Calculating the value:
b ≈ 7.96
Rounded to the nearest tenth:
b ≈ 8.0
2)To find the measure of angle B, we can use the Law of Sines. The formula is:
sin(B)/b = sin(A)/a
Plugging in the given values:
sin(B)/20 = sin(65)/26
Cross-multiplying:
sin(B) = (20 * sin(65)) / 26
Taking the inverse sine:
B ≈ [tex]sin^{(-1)[/tex]((20 * sin(65)) / 26)
Calculating the value:
B ≈ 47.5
Rounded to the nearest tenth:
B ≈ 47.5
3)To find the length of side c, we can use the Law of Sines. The formula is:
c/sin(C) = a/sin(A)
Plugging in the given values:
c/sin(65) = 125/sin(42)
Cross-multiplying:
c * sin(42) = 125 * sin(65)
Dividing both sides by sin(42):
c = (125 * sin(65)) / sin(42)
Calculating the value:
c ≈ 154.3
Rounded to the nearest tenth:
c ≈ 154.3
4)To find the length of side a, we can use the Law of Sines. The formula is:
a/sin(A) = c/sin(C)
Plugging in the given values:
a/sin(35) = 18.4/sin(52)
Cross-multiplying:
a * sin(52) = 18.4 * sin(35)
Dividing both sides by sin(52):
a = (18.4 * sin(35)) / sin(52)
Calculating the value:
a ≈ 10.5
Rounded to the nearest tenth:
a ≈ 10.5
5)To find the length of side b, we can use the Law of Sines. The formula is:
b/sin(B) = a/sin(A)
Plugging in the given values:
b/sin(65) = 12.5/sin(50)
Cross-multiplying:
b * sin(50) = 12.5 * sin(65)
Dividing both sides by sin(50):
b = (12.5 * sin(65)) / sin(50)
Calculating the value:
b ≈ 15.2
Rounded to the nearest tenth:
b ≈ 15.2
Know more about Law of Sines here:
https://brainly.com/question/30401249
#SPJ8
The complete question is :
Given the measures of AABC. answer the following question. Then round off answers to the nearest tenths.
1. If c = 10.5, m∠A = 30, m∠ B=52, find b.
2. If b=20, a = 26, m∠ A= 65, find m ∠ B.
3. If a = 125, m∠A=42, m ∠ B=65, find c.
4. If c= 18.4, m∠ B = 35, m ∠ C= 52, find a.
5. If a = 12.5, m∠A = 50, m∠ B = 65, find b
34% of f is equal to 85% of g.
What number should go in the box below?
g =
% of f
Answers
Answer:
g = 40% of f---------------------------
34% of f is equal to 0.34f and 85% of g is equal to 0.85g.
These two are same:
0.34f = 0.85gThen g is:
g = 0.34f/0.85g = 0.4fHence g = 40% of f.
If the lengths AB=4cm, BC=5cm, and CD=9cm, calculate the length AC. Write your answer to 3 significant figures.
Answers
To find the length AC, use the Pythagorean Theorem, which states that for a right triangle, the sum of the squares of the legs (the shorter sides) equals the square of the hypotenuse (the longest side). So, the length of AC is 6.40 cm
The legs are AB and BC, while the hypotenuse is AC. Therefore, you can use the Pythagorean Theorem to calculate the length of AC. Then, add CD to the length of AC to obtain the length of AD. To summarize, we have the following steps:
Step 1: Use the Pythagorean Theorem to calculate the length of AC²AB² + BC² = AC²4² + 5² = AC²16 + 25 = AC²41AC² = 41AC = √41 = 6.403124237 (rounded to 3 significant figures)
Step 2: Add CD to the length of AC to find the length of ADAD = AC + CDAD = 6.403124237 + 9 = 15.40312424 (rounded to 3 significant figures). Therefore, the length of AC is 6.40 cm (rounded to 3 significant figures).
For more questions on: Pythagorean Theorem
https://brainly.com/question/343682
#SPJ8