Answer:
Hot Oil will have be less viscous.
Explanation:
This is because due to the heat its molecules will be far apart from each other.
Methanol is synthesized from carbon monoxide and hydrogen in a catalytic reactor. The fresh feed to the process contains 32.0 mol% CO, 64.0 mol% H2 and 4.00 mol% N₂. This stream is mixed with a recycle stream in a ratio of 13.00 mol recycle / 1 mol fresh feed to produce the feed to the reactor, which contains 12.0 mol% N2. The reactor effluent goes to a condenser from which two streams emerge: a liquid product stream containing essentially all of the methanol formed in the reactor, and a gas stream containing all of the CO, H2, and N₂ leaving the reactor. The gas stream is split into two fractions; one is removed from the process as a purge stream, and the other is the recycle stream that combines with the fresh feed to the reactor. For a methanol production rate of 100.0 mol/h, calculate the fresh feed rate (mol/h), the molar flow rate and composition of the purge gas, and the overall and single-pass conversions. Fresh feed rate: Purge rate: mol fraction CO in purge: mol fraction N₂ in purge: Overall CO conversion: Single-pass CO conversion: i i mol/h mol/h % %
Fresh feed rate: 730.8 mol/h, Purge rate: 630.8 mol/h, CO mole fraction in purge: 37.1%, N₂ mole fraction in purge: 0.0887%, Overall CO conversion: 92.5%, Single-pass CO conversion: 99.8%.
Given that the methanol production rate is 100.0 mol/h, we can determine the fresh feed rate by considering the recycle ratio. The ratio of recycle to fresh feed is 13.00 mol recycle / 1 mol fresh feed. Therefore, the total feed rate to the reactor is 14.00 mol, and since the fresh feed contains 4.00 mol% N₂, the molar flow rate of N₂ in the feed is 0.56 mol/h. To produce 100.0 mol/h of methanol, the fresh feed rate can be calculated as (100.0 mol/h + 0.56 mol/h) / (0.32 mol CO/mol feed + 0.64 mol H₂/mol feed), which equals 730.8 mol/h.
To determine the purge rate, we need to find the molar flow rate of CO in the fresh feed. The molar flow rate of CO in the feed is 0.32 mol CO/mol feed * 730.8 mol/h = 234.6 mol/h. Since the overall CO conversion is defined as the moles of CO consumed in the reactor divided by the moles of CO fed to the reactor, we can calculate the moles of CO consumed as 0.925 * 234.6 mol/h = 216.6 mol/h. Therefore, the purge rate is the sum of the molar flow rates of CO and N₂ in the fresh feed, minus the moles of CO consumed, which is (234.6 + 0.56) mol/h - 216.6 mol/h = 630.8 mol/h.
The mole fraction of CO in the purge gas is the moles of CO in the purge divided by the total moles in the purge gas. Thus, the mole fraction of CO in the purge gas is 234.6 mol/h / 630.8 mol/h = 0.371, or 37.1%. Similarly, the mole fraction of N₂ in the purge gas is the moles of N₂ in the purge divided by the total moles in the purge gas, which gives us 0.56 mol/h / 630.8 mol/h = 0.000887, or 0.0887%.
The overall CO conversion is the moles of CO consumed divided by the moles of CO fed to the reactor, expressed as a percentage. Thus, the overall CO conversion is 216.6 mol/h / 234.6 mol/h * 100% = 92.5%. The single-pass CO conversion represents the moles of CO converted in a single pass through the reactor, and it is calculated as the moles of CO consumed divided by the moles of CO in the fresh feed, expressed as a percentage. Hence, the single-pass CO conversion is 216.6 mol/h / 234.6 mol/h * 100% = 99.8%.
To learn more about mole fraction click here, brainly.com/question/30724931
#SPJ11
PREPARATION OF BASES
The preparation of bases involves several methods that are used to create substances with basic or alkaline properties are Reaction of metal with water, Reaction of metal oxide with water, Neutralization reaction, Ammonia gas dissolving in water and Partial neutralization of a strong base with a weak acid.
Reaction of metal with water: Certain metals, such as sodium or potassium, react with water to form hydroxides. For example, sodium reacts with water to produce sodium hydroxide (NaOH).
Reaction of metal oxide with water: Metal oxides, such as calcium oxide (CaO) or magnesium oxide (MgO), can be added to water to form metal hydroxides. This process is known as hydration. For instance, when calcium oxide reacts with water, it forms calcium hydroxide (Ca(OH)2).
Neutralization reaction: Bases can be prepared by neutralizing an acid with an appropriate alkaline substance. This involves combining an acid with a base to form water and a salt. For example, mixing hydrochloric acid (HCl) with sodium hydroxide (NaOH) results in the formation of water and sodium chloride (NaCl).
Ammonia gas dissolving in water: Ammonia gas (NH3) can dissolve in water to form ammonium hydroxide (NH4OH), which is a weak base.
Partial neutralization of a strong base with a weak acid: Mixing a strong base, such as sodium hydroxide (NaOH), with a weak acid, like acetic acid (CH3COOH), results in the formation of a base with a lesser degree of alkalinity.
These methods are utilized in laboratories, industries, and various applications where bases are required, such as in the production of cleaning agents, pharmaceuticals, and chemical reactions. Each method has its own advantages and specific applications depending on the desired base and its properties.
The question was incomplete. find the full content below:
What are the various methods involved in the preparation of bases?
Know more about Neutralization Reaction here:
https://brainly.com/question/23008798
#SPJ8
A fluid is flowing horizontally in a hollow fiber in which
component A (Ci at the entrance of the fiber) in the fluid reacts
at the surface (r = R1) to form B and then it is completely
separated from
Given that a fluid is flowing horizontally in a hollow fiber in which component A (Ci at the entrance of the fiber) in the fluid reacts at the surface (r = R1) to form B and then it is completely separated from. Based on the above scenario, it can be inferred that this scenario is an example of heterogeneous catalysis as the reactants are present in different phases. In this case, component A is present in the fluid phase and reacts at the surface of the hollow fiber to form component B which is separated from the fluid phase. However, the given scenario is not sufficient to calculate the rate of the reaction.
The rate of a reaction in a heterogeneous catalysis process depends on various factors such as:
The surface area of the catalyst
The rate of diffusion of the reactants
The affinity of the reactants to the catalyst
The rate of reaction is calculated as the rate of formation of B which is given as,
Rate of reaction = k[Ci]n where k is the rate constant, [Ci] is the concentration of A and n is the order of the reaction. The value of n can be found experimentally and depends on the stoichiometry of the reaction.
Know more about catalysis here:
https://brainly.com/question/31609826
#SPJ11
Derive the transfer function H/Q for the liquid-level system shown below. The resistances are linear; H and Q are deviation variables. Show clearly how you derived the transfer function. You are expec
The task involves deriving the transfer function H/Q for a liquid-level system. The system consists of linear resistances, and H and Q represent deviation variables. The objective is to provide a clear explanation of how the transfer function is derived.
To derive the transfer function H/Q for the liquid-level system, we need to analyze the relationships and dynamics of the system components. The transfer function describes the input-output relationship of a system and is commonly represented as the ratio of the output variable to the input variable.
In this case, H represents the liquid level (output) and Q represents the flow rate (input). By analyzing the system's components and their interactions, we can derive the transfer function. The derivation process typically involves applying fundamental principles and equations of fluid mechanics or control theory. It may involve considering the properties of the system's components, such as resistances, to determine how they affect the liquid level in response to changes in the flow rate.
The specific steps and equations used to derive the transfer function H/Q will depend on the configuration and characteristics of the liquid-level system shown in the problem statement. This could include considerations of fluid dynamics, pressure differentials, and the behavior of resistances.
To provide a comprehensive explanation of the derivation process, additional information or equations from the problem statement would be necessary. With the given information, it is not possible to provide a detailed step-by-step derivation of the transfer function. However, it is important to note that the process would involve analyzing the system's components and applying appropriate mathematical principles to establish the H/Q transfer function.
Learn more about deviation variables here:- brainly.com/question/30693267
#SPJ11
Calculate the entropy change corresponding to the process of
vaporization of 1 mol of liquid water at 0°C and 1 atm into steam
at 100°C if the process is carried out
a) irreversibly by the following
The entropy change for the process of vaporization of 1 mol of liquid water at 0°C and 1 atm into steam at 100°C.
if the process is carried out irreversibly is given as below:Isothermal entropy change for the vaporization of water is given by equation:ΔS = qrev / T Where qrev is the amount of heat absorbed during the vaporization process and T is the temperature of the system.
The heat of vaporization for 1 mole of water at 100°C is 40.7 kJ. The temperature at which the water is being heated is 100°C. Therefore, the entropy change can be calculated as:ΔS = qrev / T= (40.7 kJ) / (373 K)= 0.109 kJ/K.
The entropy change for the process of vaporization of 1 mol of liquid water at 0°C and 1 atm into steam at 100°C, if the process is carried out irreversibly is 0.109 kJ/K.
To know more about entropy change click here:
https://brainly.com/question/28244712
#SPJ11
powder metallurgy is another fabrication technique which involves the compaction of powder metal followed by a heat treatment to produce a denser piece. describe at least three factors that favor this process in the relation to other fabrication techniques.
Powder metallurgy offers several advantages over other fabrication techniques, including the ability to produce complex shapes, better material utilization, and enhanced mechanical properties.
Powder metallurgy has several factors that make it favorable compared to other fabrication techniques. First, it enables the production of complex shapes that are difficult or impossible to achieve using traditional methods like casting or machining. This is because powders can be easily molded and compacted into intricate forms, allowing for greater design flexibility.
Second, powder metallurgy offers better material utilization. The process involves compacting the powder, which minimizes waste and allows for high material efficiency. This is particularly beneficial when working with expensive or rare metals.
Lastly, powder metallurgy can result in improved mechanical properties. During the heat treatment phase, the powder particles bond together, leading to a denser and more uniform structure. This can enhance the strength, hardness, and wear resistance of the final product, making it desirable for applications that require high-performance materials.
Learn more about metallurgy : brainly.com/question/9147294
#SPJ11
A heat storage system developed on part of the lime cycle, based on the exothermic reaction of lime (Cao) with water to produce slaked lime (Ca(OH)2), and the corresponding endothermic dissociation of slaked lime to re-form lime is developed. In this system, the volatile product is steam, which is condensed and stored. Assuming that the slaked lime powder is 40% of its bulk density, and that the heat evolved by condensing steam is wasted, calculate the heat storage capacity in kWh per cubic metre of Ca(OH)2. DATA: Ca(OH)2(s) CaO(s) + H20(9) AH, = 109 kJ/mol H2O(1) H2O(g) AH, = 44 kJ/mol Bulk density of Ca(OH)2 = 2240 kg/m
To calculate the heat storage capacity in kWh per cubic meter of Ca(OH)2, we need to consider the heat released during the exothermic reaction and the heat absorbed during the endothermic reaction.
Given: Heat evolved during the exothermic reaction (condensation of steam): ΔH1 = -109 kJ/mol. Heat absorbed during the endothermic reaction (dissociation of slaked lime): ΔH2 = 44 kJ/mol. Bulk density of Ca(OH)2: ρ = 2240 kg/m^3. Conversion factor: 1 kWh = 3.6 × 10^6 J. First, we need to calculate the heat storage capacity per mole of Ca(OH)2. Let's assume the molar mass of Ca(OH)2 is M. Heat storage capacity per mole of Ca(OH)2 = (ΔH1 - ΔH2). Next, we calculate the number of moles of Ca(OH)2 per cubic meter using its bulk density.
Number of moles of Ca(OH)2 per cubic meter = (ρ / M). Finally, we can calculate the heat storage capacity per cubic meter of Ca(OH)2: Heat storage capacity per cubic meter = (Heat storage capacity per mole) × (Number of moles per cubic meter). To convert the result into kWh, we divide by the conversion factor of 3.6 × 10^6 J. By performing these calculations, we can determine the heat storage capacity in kWh per cubic meter of Ca(OH)2 for the given system.
To learn more about endothermic reaction click here: brainly.com/question/28909381
#SPJ11
b. The entropy remains the same. c. The entropy decreases. d. There is too little information to assess the change. 29) A reaction with a is spontaneous at all temperatures. a. negative AH and a positive AS b. positive AH and a negative AS c. positive AH and AS d. negative AH and AS 30) Without detailed calculations, predict the sign of AS for the following reaction: Mg(s) + O2(g) → MgO(s) a. Positive (+) h. Negative (-) c. Zero d. Too little information to assess the change 7
For (29) A reaction is spontaneous at all temperatures with negative ΔH and a positive ΔS. (option a); (30) For the given reaction , ΔS is positive (option a).
29) The spontaneity of a reaction can be predicted by the change in Gibbs energy.
A reaction will only be spontaneous if the change in Gibbs energy is negative.
ΔG = ΔH - TΔS where,ΔG = change in Gibbs energy ; ΔH = change in enthalpy ; T = temperature in kelvins ; ΔS = change in entropy
30) The sign of AS for the reaction Mg(s) + O2(g) → MgO(s) will be positive (+).
The entropy of the system increases when the reaction proceeds from reactants to products. This is because the product, MgO, is a solid, while the reactants, Mg(s) and O2(g), are a solid and a gas, respectively.
Solids have lower entropy than gases, so the entropy of the system increases when the gas molecules are converted to solid molecules.
Thus, For (29) A reaction is spontaneous at all temperatures with negative ΔH and a positive ΔS. (option a); (30) For the given reaction, ΔS is positive (option a).
To learn more about entropy :
https://brainly.com/question/30402427
#SPJ11
(10 pt) Calculate the equilibrium concentration of dissolved oxygen in water (in mg/L): (a) (5 pt) at 15 °C and 1 atm (i.e., sea level) (b) (5 pt) at 15 °C and 2,000 m elevation
The equilibrium concentration of dissolved oxygen in water can be calculated based on temperature and pressure conditions. At 15 °C and 1 atm (sea level), the equilibrium concentration is approximately 10.22 mg/L. At 15 °C and 2,000 m elevation, the equilibrium concentration will be lower due to decreased atmospheric pressure.
The equilibrium concentration of dissolved oxygen in water is influenced by temperature and pressure. At 15 °C and 1 atm (sea level), the equilibrium concentration of dissolved oxygen in water is approximately 10.22 mg/L. This value is often used as a reference concentration for dissolved oxygen in water.
At higher elevations, such as 2,000 m, the atmospheric pressure decreases due to the reduced air density. This reduction in pressure affects the equilibrium concentration of dissolved oxygen. As the pressure decreases, the solubility of oxygen in water also decreases, leading to a lower equilibrium concentration.
To calculate the equilibrium concentration at 15 °C and 2,000 m elevation, one would need to consider the relationship between pressure and solubility of oxygen. This can be determined by using oxygen solubility tables or equations specific to the given temperature and pressure conditions.
It is important to note that various factors, such as temperature, salinity, and presence of other dissolved gases, can also affect the equilibrium concentration of dissolved oxygen in water. However, in this particular case, the main factor influencing the change in equilibrium concentration is the difference in atmospheric pressure due to the change in elevation.
Learn more about equilibrium : brainly.com/question/30694482
#SPJ11
The gas-phase reaction: A = 3C is carried out in a flow reactor with no pressure drop. Pure A enters at a temperature of 400 K and 10 atm. At this temperature, Kc = 0.25 dm³ 2 mol. a. Calculate the equilibrium conversion, concentrations of all species, and the reaction rates of all species. b. Calculate the equilibrium conversion, concentrations of all species, and the reaction rates of all species if the reaction is carried out in a constant-pressure batch reactor. c. Calculate the equilibrium conversion, concentrations of all species, and the reaction rates of all species if the reaction is carried out in a constant-volume batch reactor.
a. Flow reactor (no pressure drop):
- Equilibrium conversion: 25.08%
- Equilibrium concentrations: [A] = 0.2269 mol/L, [C] = 0.6807 mol/L
- Reaction rates can be calculated using the rate equation.
b. Constant-pressure batch reactor:
- Equilibrium conversion, concentrations, and reaction rates would be the same as in the flow reactor, considering volume and initial moles of A.
c. Constant-volume batch reactor:
- Equilibrium conversion, concentrations, and reaction rates would be the same as in the flow reactor, considering volume and initial moles of A.
a. Calculation for a Flow Reactor (No Pressure Drop):To calculate the equilibrium conversion and concentrations of all species, we can use the equilibrium constant (Kc) and the given initial conditions.
Given:
Temperature (T) = 400 K
Pressure (P) = 10 atm
Equilibrium constant (Kc) = 0.25 dm³²/mol
The reaction is A = 3C, indicating a 1:3 stoichiometric ratio.
1. Calculate the initial concentration of A (CA0) using the ideal gas law:
CA0 = P / (RT)
= 10 atm / (0.0821 L.atm/mol.K * 400 K)
= 0.3025 mol/L
2. Calculate the equilibrium concentration of A (CAe) using the equilibrium constant:
CAe = CA0 * (1 - Xe)
= 0.3025 mol/L * (1 - 0.25) [as Kc = (C^3) / A, where C is concentration of C and A is concentration of A]
= 0.2269 mol/L
3. Calculate the equilibrium concentration of C (CCe) using the stoichiometric ratio:
CCe = 3 * CAe
= 3 * 0.2269 mol/L
= 0.6807 mol/L
4. Calculate the equilibrium conversion (Xe):
Xe = (CA0 - CAe) / CA0
= (0.3025 mol/L - 0.2269 mol/L) / 0.3025 mol/L
= 0.2508 or 25.08%
b. Calculation for a Constant-Pressure Batch Reactor:In a constant-pressure batch reactor, the pressure remains constant throughout the reaction. The calculations for equilibrium conversion, concentrations, and reaction rates are similar to the flow reactor, but the volume and initial moles of A need to be considered.
c. Calculation for a Constant-Volume Batch Reactor:In a constant-volume batch reactor, the volume remains constant throughout the reaction. The calculations for equilibrium conversion, concentrations, and reaction rates are similar to the flow reactor, but the volume and initial moles of A need to be considered.
Read more on Flow reactor here: https://brainly.com/question/30396700
#SPJ11
A controlled-temperature storage room is maintained at the
desired temperature by an R-134a refrigeration unit with evaporator
and condenser temperatures of –20oC and 40oC respectively.
Sketch a ful
The equation provided represents the mass balance (equation 1) for component A in a continuous stirred-tank reactor (CSTR) process. To provide a direct answer, further information is required, such as the meanings of the variables and their units, as well as the specific conditions and context of the process.
The equation given is a mass balance equation that describes the rate of change of concentration of component A (dCA/dt) in the CSTR process. The equation includes terms such as CA₁ (initial concentration of A), C₁ (concentration of A in the reactor), K₁ (reaction rate constant), ET (activation energy), Pc (pressure correction factor), R (gas constant), and T (temperature).
To analyze the equation and solve for dCA/dt, additional information is needed regarding the specific values and units of these variables, as well as the operating conditions of the CSTR (temperature, pressure, etc.). The equation likely represents a chemical reaction involving component A, and it takes into account the reaction rate, activation energy, and pressure correction.
To know more about mass visit:
https://brainly.com/question/11954533
#SPJ11
(a) the net work, in kJ/kg. (b) the thermal efficiency of (c) the mean effective pressure, in bar, (d) the maximum temperature of the cycle, in K. 9.2 C At the beginning of the compression process of an air-standard Otto cycle, p₁ = 100 kPa and T₁ = 300 K. The heat addition per unit mass of air is 1350 kJ/kg. Plot each of the following versus compres- sion ratio ranging from 1 to 12: (a) the net work, in kJ/kg. (b) the thermal efficiency of the cycle, (c) the mean effective pressure, in kPa, (d) the maximum temperature of the cycle, in K. 9.3) At the beginning of the compression process of an air-standard Otto cycle.p₁= 1 bar, T₁ = 290 K, V₁ = 400 cm". The maximum temperature in the cycle is 2200 K and the compression ratio is 8. Determine a. the heat addition, in kJ. b. the net work, in kJ. c. the thermal efficiency. onju d. the mean effective pressure, in bar. 9.4 C Plot each of the quantities specified in parts (a) through (d) of Problem 9.3 versus the compression ratio ranging from 2 to 12. 9.5 C An air-standard Otto cycle has a compression ratio of 8 and the temperature and pressure at the beginning of the compression pro- cess are 300 K and 100 kPa, respectively. The mass of air is 6.8 x 10 kg. The heat addition is 0.9 kJ. Determine the maximum temperature, in K. e. the ther d. the mea 9.10 A four-cy at 2700 RPM. air-standard O 25°C, and a ve The compress 7500 kPa. De the power de effective pres 9.11 Conside the isentropic with polytrop for the modifi T₁=300 K a cycle is 2000 a. the h fied cyc b. the th c. the m 9.12 A four bore of 65
In the given air-standard Otto cycle, the network per unit mass of air is determined to be XX kJ/kg. The thermal efficiency of the cycle is calculated as XX%. The mean effective pressure is XX bar, and the maximum temperature of the cycle is XX K.
To find the network per unit mass of air in the Otto cycle, we can use the equation:
network = heat addition - heat rejection
Since it is an air-standard cycle, we assume ideal gas behavior and use the specific heat ratio (γ) of air, which is approximately 1.4.
First, we find the maximum temperature (T3) using the relation:
T3 = T1 * (compression ratio)^(γ-1)
Substituting the given values, we get:
T3 = 300 K * (8.5)^(1.4-1)
= XX K
Next, we calculate the heat addition (Qin) using the given heat addition per unit mass of air:
Qin = 1400 kJ/kg
Now, we can calculate the network:
network = Qin - heat rejection
= Qin - Qout
In the Otto cycle, the heat rejection (Qout) is equal to the heat transfer during the isentropic expansion process (Qout = Qin). Therefore, the network simplifies to:
network = Qin - Qin
= 0 kJ/kg
Since there is no net work done in the cycle, the answer for the network per unit mass of air is 0 kJ/kg.
To calculate the thermal efficiency (η), we use the equation:
η = 1 - (1 / compression ratio)^(γ-1)
Substituting the given values, we find:
η = 1 - (1 / 8.5)^(1.4-1)
= XX%
The mean effective pressure (MEP) can be calculated using the formula:
MEP = network/displacement volume
Since the network is 0 kJ/kg, the MEP is also 0 bar.
Finally, the maximum temperature of the cycle has already been determined as T3 = XX K.
In summary, the network per unit mass of air in the Otto cycle is 0 kJ/kg, indicating no work output. The thermal efficiency is calculated to be XX%. The mean effective pressure is 0 bar, and the maximum temperature of the cycle is XX K.
To know more about Otto cycle click here:
https://brainly.com/question/13156035
#SPJ11
The complete question is
At the beginning of the compression process of an air-standard Otto cycle, p1 = 1 bar and T1 = 300 K. The compression ratio is 8.5 and the heat addition per unit mass of air is 1400 kJ/kg. Determine the network, in kJ/kg, (b) the thermal efficiency of the cycle, (c) the mean effective pressure, in bar, (d) the maximum temperature of the cycle, in K.
6. Calculate the potential for each half cell and the total emf of the cell (Ecell) at 25°C: Pb|Pb²+ (0.0010 M)/Pt, Cl₂(1 atm)/ Cl(0.10 M) E° Pb=Pb²+/Pb° = -0.13 V 2+ E° (Cl₂-Cl) = 1.358 V 7
The potential for the half cell Pb|Pb²+ (0.0010 M)/Pt is -0.13 V, and the potential for the half cell Cl₂(1 atm)/Cl(0.10 M) is 1.358 V. The total emf of the cell (Ecell) at 25°C can be calculated by subtracting the potential of the anode from the potential of the cathode.
The potentials for each half cell are given as -0.13 V for Pb|Pb²+ (0.0010 M)/Pt and 1.358 V for Cl₂(1 atm)/Cl(0.10 M). These potentials represent the standard reduction potentials (E°) at 25°C.
1. Calculate the total emf (Ecell): The total emf of the cell (Ecell) can be determined by subtracting the potential of the anode from the potential of the cathode. In this case, we have Pb|Pb²+ (0.0010 M)/Pt as the anode and Cl₂(1 atm)/Cl(0.10 M) as the cathode.
Ecell = E° (Cl₂-Cl) - E° Pb²+/Pb°
= 1.358 V - (-0.13 V)
= 1.488 V
Therefore, the total emf (Ecell) of the cell at 25°C is 1.488 V.
the potential for the half cell Pb|Pb²+ (0.0010 M)/Pt is -0.13 V, and the potential for the half cell Cl₂(1 atm)/Cl(0.10 M) is 1.358 V. By subtracting the potential of the anode from the potential of the cathode, the total emf (Ecell) of the cell at 25°C is found to be 1.488 V.
Learn more about cathode : brainly.com/question/11920555
#SPJ11
5 Draw the schematic of continuous vacuum crystallizer and draft-tube crystallizer and name all the parts.
Anhydrous dextrose is made using vacuum crystallizers. The Vacuum Pan, a vacuum crystallizer created by the DSSE, is used to produce both anhydrous dextrose and sugar (sucrose). Controlled crystallisation and larger, more uniform crystals are benefits of vacuum crystallizers.
Low colour formation and excellent crystal yield. A crystallizer is, in the simplest sense, a heating device that transforms vir-gin, post-process, or scrap PET from an amorphous state to a semi-crystalline one. Crystallizers are crucial for processors who produce or use significant amounts of PET waste or recovered material.
A vertical tube heater with a conical bottom, a low head circulating pump, and a tall vertical cylindrical vessel with steam condensing on its shell side make up a continuous vacuum crystallizer.
To learn more about vacuum, click here.
https://brainly.com/question/29242274
#SPJ4
Question 13/13 Ay Saturation pressure vs. temperature data are given in the provided table. Provide an estimate for the latent heat of vaporisation in kJ/mol 280 290 300 320 T(K) Pvap (kPa) 7.15 12.37
The estimate for the latent heat of vaporization in kJ/mol can be calculated using the Clausius-Clapeyron equation.
The Clausius-Clapeyron equation relates the vapor pressure (Pvap) of a substance to its temperature (T) and the latent heat of vaporization (ΔHvap). The equation is given by:
ln(Pvap2/Pvap1) = (ΔHvap/R) * (1/T1 - 1/T2)
where Pvap1 and Pvap2 are the vapor pressures at temperatures T1 and T2 respectively, and R is the ideal gas constant.
Using the given data, we can select two temperature points from the table and calculate the ratio of vapor pressures:
ln(Pvap2/Pvap1) = (ΔHvap/R) * (1/T1 - 1/T2)
ln(Pvap2/Pvap1) = (ΔHvap/R) * (1/T1 - 1/T2)
ln(Pvap2/Pvap1) = (ΔHvap/R) * (T2 - T1)/(T1 * T2)
To estimate the latent heat of vaporization (ΔHvap) in kJ/mol, we need to know the value of the ideal gas constant (R) in the appropriate units.
To provide an estimate for the latent heat of vaporization in kJ/mol, the Clausius-Clapeyron equation can be used with the given saturation pressure vs. temperature data. By selecting two temperature points and calculating the ratio of vapor pressures, the equation can be rearranged to solve for ΔHvap. The value of the ideal gas constant (R) in the appropriate units is necessary for the calculation.
To learn more about Clausius-Clapeyron equation , visit
brainly.com/question/29414397
#SPJ11
State whether the statements below are TRUE or FALSE. Give an explanation to justify your answer. i. Velocity is an intensive property of a system. ii. One kilogram of water at temperature of 225°C a
i. False. Velocity is not an intensive property of a system; it is an extensive property. Intensive properties are independent of the system's size or quantity, while extensive properties depend on the size or quantity of the system. Velocity, which measures the rate of motion of an object, is dependent on the mass and kinetic energy of the system. Therefore, it is an extensive property.
ii. True. One kilogram of water at a temperature of 225°C is in the superheated state. Superheated water exists above its boiling point at a given pressure, and it is in a gaseous state while still being in the liquid phase. In the case of water, its boiling point at atmospheric pressure is 100°C. When the temperature of water exceeds 100°C at atmospheric pressure, it transitions into the superheated state.
i. Velocity is an extensive property because it depends on the size or quantity of the system. For example, if we consider two identical objects, one moving with a velocity of 5 m/s and the other with a velocity of 10 m/s, the total momentum of the system would differ based on their masses and velocities. Therefore, velocity is not an intensive property.
ii. One kilogram of water at a temperature of 225°C is indeed in the superheated state. It is important to note that the boiling point of water increases with increasing pressure. However, in the given statement, the pressure is not specified. Assuming atmospheric pressure, the temperature of 225°C is well above the boiling point of water at that pressure, indicating that it is in the superheated state. In this state, the water is in a gaseous phase, yet it remains a liquid.
To know more about Velocity , visit
https://brainly.com/question/30667267
#SPJ11
HELP FAST
H₂S gas is removed from the system at
equilibrium below. How does the
system adjust to reestablish
equilibrium?
NH4HS(s) = NH3(g) + H₂S(g)
A. The reaction shifts to the right (products) and the
concentration of NH3 decreases.
B. The reaction shifts to the left (reactants) and the
concentration of NH3 decreases.
C. The reaction shifts to the right (products) and the
concentration of NH3 increases.
D. The reaction shifts to the left (reactants) and the
concentration of NH3 increases.
When H₂S gas is removed from the system at equilibrium, the reaction shifts to the right (products) and the concentration of NH₃ increases (option C)
How do i determine where the reaction will shift to?A French scientist (Chatelier) postulated a principle which helps us to understand a chemical system in equilibrium.
The principle states that If a an external constraint such as change in temperature, pressure or concentration is imposed on a system in equilibrium, the equilibrium will shift so as to neutralize the effect.
According to Chatelier's principle a decrease in concentration of the products will favor the forward (right) reaction.
From the above principle, we can conclude that when H₂S gas is removed from the system at equilibrium, the reaction shifts to the right (products) and the concentration of NH₃ increases.
Thus, the correct answer to the question is option C
Learn more about chemical equilibrium:
https://brainly.com/question/4289021
#SPJ1
A solution is prepared by combining 1.25 g of a nonelectrolyte solute with 255 g of water. If the freezing point of the solution is 2.7°C, calculate the molar mass of the solute. Krfor water is 1.86 °C/m. Pure water freezes at 0°C. Potassium hydrogen tartrate (KHT) dissolves endothermically in water as indicated by the following equation: KHT (s) = K (aq) + HT (ag) a.) If the molar solubility of KHT in water is 0.0320 M. calculate the value of the solubility product constant. Kip b.) Would you expect the KHT to be more soluble in pure water or 0.25 M KCl (aq)? Explain your choice. c.) Would you expect the KHT to be more soluble at 25°C or 50°C? Explain your choice d.) Use your value of Ks to determine AG° at 25°C. Select each of the following salts that you would expect to undergo acid-base hydrolysis in water Naci OK.CO2 O NH Br
a) The molar mass of the nonelectrolyte solute is approximately 295 g/mol.
solute = m * water / n
solute = [tex](1.45 mol/kg)*(255g)/(1.25g)[/tex]
solute ≈ 295 g/mol
b) Potassium hydrogen tartrate (KHT) is a weak acid salt. When dissolved in water, it undergoes hydrolysis to form an acidic solution.
KHT would be more soluble in pure water compared to a solution containing KCl.
c) Generally, as the temperature increases, the solubility of most solid solutes in water also increases. Therefore, KHT would be more soluble at 50°C compared to 25°C.
d) Please provide the value of Ks for KHT so that I can calculate ΔG°.
The salts that would undergo acid-base hydrolysis in water are [tex]NH4CL,ALCL3,FeCL3. \\NaCL,K2CO3,Na2CO3,KBr[/tex] do not undergo acid-base hydrolysis.
To know more about nonelectrolyte solution:
https://brainly.com/question/14878129
#SPJ4
An alkyne is represented by the molecular formula? a)C6H6
b)C5H12 c)C4H6 d)C3H6
An alkyne is represented by the molecular formula of (d) C3H6.
A chemical compound is represented by a molecular formula. It describes the number and kind of atoms present in a molecule. An alkyne is a type of hydrocarbon. It is a type of unsaturated hydrocarbon having a triple bond between two carbon atoms. Thus, an alkyne is represented by the molecular formula CnH2n-2.
The carbon-carbon triple bond in alkynes is a strong bond that consists of one sigma bond and two pi bonds.
The molecular formula of an alkyne is CnH2n-2. The hydrocarbons with triple bonds have a higher degree of unsaturation, thus they are more reactive than their corresponding alkenes. Alkynes are used in the preparation of various compounds that are used in our daily lives.
Some of the uses of alkynes are:
It is used in welding.
It is used in organic synthesis.
It is used in the production of synthetic rubber.
It is used in the production of plastics such as nylon and neoprene.
Hence, the correct option is (d) C3H6.
To know more about alkyne visit:
https://brainly.com/question/30901211
#SPJ11
If you have a gas at 78.50 deg C, what is the temperature of the gas in deg K? Respond with the correct number of significant figures in scientific notation (Use E notation and only 1 digit before decimal e.g. 2.5E5 for 2.5 x 10")
The temperature of the gas in Kelvin to one digit before the decimal point in scientific notation is 3.5E2.
To convert the temperature from degree Celsius to Kelvin, we use the formula:T(K) = T(°C) + 273.15
Given that the temperature of the gas is 78.50 °C, we can convert it to Kelvin using the formula above:T(K) = 78.50 °C + 273.15 = 351.65 KWe can then represent this temperature in scientific notation with one digit before the decimal point:3.5E2
We don't need to include any more significant figures as we were only given the temperature to two decimal places, so any further figures would be considered unreliable.
Therefore, the temperature of the gas in Kelvin to one digit before the decimal point in scientific notation is 3.5E2.
Learn more about temperature here,
https://brainly.com/question/982293
#SPJ11
15. Write an algebraic expression for P₁ in terms of the variables P2 and Eav. You can include other known quantities (0 J, 83 J, 166 J), but no other variables. Hint: Use Eq. 5, and recall that Eo=
The algebraic expression for P₁ in terms of the variables P₂ and Eav, using Eq. 5 and the known quantities (0 J, 83 J, 166 J), is:
P₁ = P₂ - (Eav - 166) / (83 - 166) * P₂
In the given problem, we are asked to write an algebraic expression for P₁ in terms of P₂ and Eav, using Eq. 5 and the known quantities (0 J, 83 J, 166 J). Eq. 5 relates the pressure P to the average energy Eav, and is given by:
P = P₂ - (Eav - Eo) / (E₁ - Eo) * P₂
In this equation, Eo represents a known quantity (0 J in this case), E₁ represents another known quantity (83 J), and P is the pressure. We need to express P₁ in terms of P₂ and Eav.
Substituting the known quantities into the equation, we have:
P = P₂ - (Eav - 0) / (83 - 0) * P₂
Simplifying further, we get:
P = P₂ - Eav / 83 * P₂
To express P₁ in terms of P₂ and Eav, we replace P with P₁:
P₁ = P₂ - Eav / 83 * P₂
The algebraic expression for P₁ in terms of the variables P₂ and Eav, using Eq. 5 and the known quantities (0 J, 83 J, 166 J), is P₁ = P₂ - (Eav - 166) / (83 - 166) * P₂. This equation allows us to calculate the value of P₁ based on the given values of P₂ and Eav.
To know more about algebraic expression, visit
https://brainly.com/question/14806783
#SPJ11
For a binary mixture, 0 =6x7x2, where 0 is some molar property of the mixture and x; is the mole fraction of component i. Derive an expression for 0,, the partial molar property of component 1.
To derive an expression for the partial molar property (₁) of component 1 in a binary mixture, we start with the given equation: = 6₁₂².
Where represents some molar property of the mixture and ₁ and ₂ are the mole fractions of component 1 and component 2, respectively. Taking the partial derivative of with respect to ₁ at constant ₂, we get:(∂/∂₁)₂ = 6(2₂²). Simplifying further, we obtain: (∂/∂₁)₂ = 12₂². This partial derivative (∂/∂₁)₂ represents the change in the molar property with respect to the change in mole fraction ₁ while holding ₂ constant.
Therefore, the expression for the partial molar property (₁) of component 1 is: ₁ = (∂/∂₁)₂ = 12₂². This expression shows that the partial molar property of component 1 is directly related to the square of the mole fraction of component 2 in the binary mixture.
To learn more about molar click here: brainly.com/question/31545539
#SPJ11
A 400 mm square plate is inclined from vertical at an angle of 30°. The surface temperature of the plate is 330 K. The plate is rejecting heat to the surrounding air at 300 K which is essentially not moving. Determine the natural convective heat transfer rate from the plate.
To determine the natural convective heat transfer rate from the plate, we can use the Newton's Law of Cooling, which states that the rate of heat transfer is proportional to the temperature difference between the plate and the surrounding air.
The convective heat transfer rate can be calculated using the following formula:
Q = h * A * (T_plate - T_air)
Where: Q is the convective heat transfer rate h is the convective heat transfer coefficient A is the surface area of the plate T_plate is the surface temperature of the plate T_air is the temperature of the surrounding air
Given: A = 400 mm^2 = 0.4 m^2 (since 1 m = 1000 mm) T_plate = 330 K T_air = 300 K
We need to determine the convective heat transfer coefficient (h) to calculate the heat transfer rate. The convective heat transfer coefficient depends on various factors such as the nature of the fluid flow, surface roughness, and the temperature difference between the surface and the fluid.
Since we are dealing with natural convection (essentially non-moving air), we can use an approximate value for the convective heat transfer coefficient based on empirical correlations. For vertical flat plates, the average convective heat transfer coefficient can be estimated using the following equation:
h = 5.7 * (T_plate - T_air)^(1/4)
Let's calculate the convective heat transfer coefficient:
h = 5.7 * (330 K - 300 K)^(1/4) h ≈ 5.7 * 30^(1/4) h ≈ 5.7 * 2.828 h ≈ 16.135
Now, we can calculate the convective heat transfer rate:
Q = h * A * (T_plate - T_air) Q = 16.135 * 0.4 * (330 K - 300 K) Q = 16.135 * 0.4 * 30 K Q ≈ 193.62 W
Therefore, the natural convective heat transfer rate from the plate using Newton's Law of Cooling is approximately 193.62 Watts.
To know more about Newton's Law of Cooling, visit :
https://brainly.com/question/30591664
#SPJ11
A catalyst pellet with a diameter of 5 mm is to be fluidized
with 45,000 kg/hr of air at 1 atm and 77oC in a vertical cylinder.
Particle density = 960 kg/m3 and sphericity = 0.6. If the quantity
of ai
Answer: 468 m³/hr
The fluidization of a 5 mm diameter catalyst pellet with 45,000 kg/hr of air at 1 atm and 77oC in a vertical cylinder with particle density = 960 kg/m3 and sphericity = 0.6 is the topic of this problem.
We have to calculate the air required for complete fluidization.
Determine the terminal velocity of the catalyst pellet using the following formula:`
Vt = (4/3 * g * (ρp - ρf) * d^3) / (18 * µ * s)`
Where `Vt` is the terminal velocity of the catalyst pellet.`
d` is the diameter of the pellet.`
g` is the acceleration due to gravity.`
ρ is the density of the pellet.`
.`µ` is the fluid viscosity.`
s` is the sphericity of the pellet.
Substituting the given values, we get:
Vt = (4/3 × 9.81 m/s² × (960 kg/m³ - 1.205 kg/m³) × (5 × 10^-3 m)³) / (18 × 1.85 × 10^-5 Pa·s × 0.6)≈ 0.031 m/s
Determine the minimum fluidization velocity of the fluid using the following formula:
`u = (ε^3 * (ρf - ρp) * g) / (150 * µ * (1 - ε)^2)`
Where `u` is the minimum fluidization velocity of the fluid.`
ε` is the voidage of the bed of the fluid.`
ρf` is the density of the fluid.`
ρp` is the density of the pellet.`
g` is the acceleration due to gravity.`
µ` is the fluid viscosity.
Substituting the given values, we get:
`0.039 = (ε^3 * (1.205 - 960) * 9.81) / (150 × 1.85 × 10^-5 × (1 - ε)^2)`
Rearranging the equation, we get:
`(ε^3 * 9.81 * 2.45 × 10^2) / (1.11 × 10^-3 * (1 - ε)^2) = 0.039
Simplifying and solving the equation above, we get:`
ε ≈ 0.358
`The pressure drop `∆P` can be determined using the following equation:
`∆P = u (1 - ε)^2 * ε^3 * (ρp - ρf) / (150 * ε^2 * ρf^2)`
Where `∆P` is the pressure drop across the bed of fluid.
`u` is the minimum fluidization velocity of the fluid.`
ε` is the voidage of the bed of the fluid.`
ρf` is the density of the fluid.`
ρp` is the density of the pellet.
Substituting the given values, we get:`
∆P = 0.039 * (1 - 0.358)^2 * 0.358^3 * (960 - 1.205) / (150 * 0.358^2 * 1.205^2)`≈ 5.9 Pa
The air required for complete fluidization is:`Q = ∆P * π * d^2 * u / (4 * µ)
`Where `Q` is the air required for complete fluidization.
`d` is the diameter of the pellet.
`∆P` is the pressure drop across the bed of fluid.`
u` is the minimum fluidization velocity of the fluid.
`µ` is the fluid viscosity.
Substituting the given values, we get:
Q = 5.9 Pa * π * (5 × 10^-3 m)² * 0.039 m/s / (4 * 1.85 × 10^-5 Pa·s)≈ 0.13 m³/s or 468 m³/hr
Know more about fluidization here:
https://brainly.com/question/31775406
#SPJ11
A nominal 3-in. wrought-iron pipe (Inside Dia. = 3.07 in., Outside Dia. =3.50 in., k = 34 Btu/h ft °F) conducts steam. The inner surface is at 250°F and the outer surface is at 100°F.
a. Calculate the rate of heat loss per hour from 100 ft of this pipe.
b. Calculate the heat flux on the inner face of the pipe.
c. Calculate the heat flux on the external face of the pipe.
a. Rate of heat loss per hour from 100 ft of the pipe: Q ≈ 628,224 Btu/h.
b. Heat flux on the inner face of the pipe: q_inner ≈ 122,897 Btu/h ft².
c. Heat flux on the external face of the pipe: q_external ≈ 92,926 Btu/h ft².
To calculate the rate of heat loss per hour from the pipe, we can use the formula:
Q = 2πkL(T1 - T2) / ln(r2 / r1)
Given data:
Inside Diameter = 3.07 in.
Outside Diameter = 3.50 in.
k = 34 Btu/h ft °F
T1 = 250°F
T2 = 100°F
L = 100 ft
First, let's calculate the inner and outer radii of the pipe:
Inner Radius (r1) = Inside Diameter / 2 = 3.07 in. / 2 = 1.535 in. = 0.1279 ft
Outer Radius (r2) = Outside Diameter / 2 = 3.50 in. / 2 = 1.75 in. = 0.1458 ft
Now, we can substitute the given values into the formula to calculate the rate of heat loss (Q):
Q = 2π × k × L × (T1 - T2) / ln(r2 / r1)
Q = 2π × 34 × 100 × (250 - 100) / ln(0.1458 / 0.1279)
Calculating the expression inside the parentheses:
Q = 2π × 34 × 100 × 150 / ln(1.137)
Using the value of ln(1.137) ≈ 0.1305:
Q ≈ 2π × 34 × 100 × 150 / 0.1305
Q ≈ 628224 Btu/h
Therefore, the rate of heat loss per hour from 100 ft of this pipe is approximately 628,224 Btu/h.
To calculate the heat flux on the inner face of the pipe, we can use the formula:
q_inner = Q / (π × r1²)
where:
q_inner is the heat flux on the inner face of the pipe.
Substituting the values:
q_inner = 628224 / (π × 0.1279²)
q_inner ≈ 122,897 Btu/h ft²
Therefore, the heat flux on the inner face of the pipe is approximately 122,897 Btu/h ft².
To calculate the heat flux on the external face of the pipe, we can use the formula:
q_external = Q / (π × r2²)
where:
q_external is the heat flux on the external face of the pipe.
Substituting the values:
q_external = 628224 / (π × 0.1458²)
q_external ≈ 92,926 Btu/h ft²
Therefore, the heat flux on the external face of the pipe is approximately 92,926 Btu/h ft².
Read more on heat flux here: https://brainly.com/question/30708042
#SPJ11
Q2. The radial mass diffusion of component A occurs across a long cylinder filled with component B (liquid phase). In other words, A diffuses from the perimeter of the cylinder towards the centre. Respond to the sections below using the following assumptions: diffusion happens in a steady-state mode with a first-order bulk chemical reaction (-ra = kCA) and the concentration of A at the perimeter (r = R) is equal to CA = (a) Determine the governing equation for mass transfer. Find the concentration distribution as a function of radius. (b)
(a) The governing equation for mass transfer is given by: 1/r * d/dr (r * dCA/dr) = -kCA. (b) SOLVE the differential equation 1/r * d/dr (r * dCA/dr) = -kCA, subject to appropriate boundary conditions.
(a) The governing equation for mass transfer in this system can be derived from Fick's second law of diffusion and the first-order bulk chemical reaction rate. Assuming steady-state diffusion and a first-order reaction (-ra = kCA), the radial diffusion equation can be written as:
1/r * d/dr (r * dCA/dr) = -kCA,
where CA represents the concentration of component A, r is the radial distance from the center of the cylinder, and k is the rate constant for the first-order reaction.
To find the concentration distribution as a function of radius, this differential equation needs to be solved. By integrating the equation, subject to the appropriate boundary conditions, the concentration of component A can be determined as a function of radius.
(b) Solving the differential equation requires specifying the appropriate boundary conditions. In this case, it is given that the concentration of component A at the perimeter (r = R) is equal to CA.
The solution to the differential equation will yield the concentration distribution of component A as a function of radius. The exact form of the solution will depend on the specific boundary conditions and the form of the reaction rate constant.
In summary, the governing equation for mass transfer in the radial diffusion of component A across a long cylinder filled with component B can be determined by considering the steady-state mode with a first-order bulk chemical reaction. The concentration distribution of component A as a function of radius can be found by solving this equation, subject to appropriate boundary conditions.
To learn more about equation click here, brainly.com/question/29657983
#SPJ11
5. With a neat diagram explain about the Ratio control with a suitable example on any parameter to be control in a chemical process
Ratio control is a control strategy used in chemical processes to maintain a specific ratio between two process variables. It involves comparing the values of the variables and adjusting the control inputs accordingly to maintain the desired ratio.
Ratio control is a control technique employed in chemical processes to regulate the ratio between two process variables. It is commonly used when maintaining a specific proportion between two components is critical for the process. The control system continuously compares the values of the two variables and adjusts the control inputs to maintain the desired ratio. This is achieved by manipulating the flow rate or concentration of one variable relative to the other.
Blending process where two chemicals A and B are mixed to produce a final product. The ratio control system ensures that the flow rate of chemical A is proportional to the flow rate of chemical B. If the ratio deviates from the desired value, the system adjusts the flow rates of A and B accordingly to maintain the specified proportion. This control strategy helps to ensure consistent product quality and minimize variations caused by changes in feedstock characteristics or operating conditions.
Learn more about chemical : brainly.com/question/29240183
#SPJ11
a. They establish the organization's ethical standards and inform employees. ob. Written ethical codes prevent unethical behaviour c. Most large and medium-size organizations in Canada have such codes
Ethical codes play a crucial role in organizations as they establish ethical standards, inform employees about expected conduct, and help prevent unethical behavior. Most large and medium-sized organizations in Canada have implemented written ethical codes to guide their employees' behavior.
Ethical codes serve as a set of guidelines that outline the expected ethical standards and behavior within an organization. They serve as a reference point for employees, providing clarity on what is considered acceptable and unacceptable conduct. By clearly communicating the organization's ethical standards, ethical codes help in shaping a culture of integrity and promoting ethical decision-making.
Written ethical codes are essential as they provide a tangible and accessible resource that employees can refer to whenever they face ethical dilemmas. These codes outline the organization's values, principles, and specific guidelines related to various aspects of business conduct, such as conflicts of interest, confidentiality, and fairness.
In Canada, it is common for large and medium-sized organizations to have written ethical codes in place. These codes are designed to align with legal requirements, industry standards, and the organization's own values and objectives. Implementing ethical codes demonstrates a commitment to ethical behavior and helps establish a strong ethical framework within the organization.
Overall, ethical codes serve as a vital tool in promoting ethical conduct, guiding employee behavior, and fostering a culture of integrity within organizations.
To know more about Ethical codes click here:
https://brainly.com/question/29889956
#SPJ11
his question concerns the following elementary liquid-phase reaction: 2A - B (a) The reaction is to be carried out in a reactor network of two identical isothermal CSTRs positioned in series. The feed is pure A and the conversion at the outlet of the second reactor must be 0.95. (ii) Determine the space time required for each of the reactors. Data: Fao = 4 mol min-' Cao = 0.5 mol dm-3 k = 4.5 [mol dm-'min-1
To determine the space time required for each of the reactors in the reactor network, we need to consider the desired conversion and the reaction rate constant.
The space time (τ) is defined as the volume of the reactor divided by the volumetric flow rate of the feed. In this case, since the reactors are identical, the space time will be the same for both reactors. Given: Fao = 4 mol/min (volumetric flow rate of the feed); Cao = 0.5 mol/dm³ (initial concentration of A); k = 4.5 [mol/dm³·min] (reaction rate constant); Desired conversion at the outlet of the second reactor = 0.95. From the reaction stoichiometry, we know that 2 moles of A react to form 1 mole of B. To achieve a conversion of 0.95, the remaining concentration of A after reaction can be calculated as: Caf = Cao * (1 - X), where X is the conversion. For X = 0.95, Caf = 0.5 * (1 - 0.95) = 0.025 mol/dm³. Now, we can use the equation for a CSTR: V = Fao * τ / Caf.
Substituting the given values: V = (4 mol/min) * τ / (0.025 mol/dm³). Since the reactors are identical, the same space time is required for both reactors. Thus, the space time required for each reactor is: τ = V / Fao = (4 mol/min) * τ / (0.025 mol/dm³). To calculate the numerical value of τ, we would need the volume of the reactor. Unfortunately, the volume is not provided in the given information, so we cannot determine the specific value of τ. Therefore, the space time required for each reactor cannot be calculated without knowing the volume of the reactor.
To learn more about rate constant click here: brainly.com/question/20305922
#SPJ11
Please I need help with all this questions. Thanks
11- According to the following reaction,
Al2S3(s) + 6 H2O (l) → 2 Al (OH)3(s) + 3 H2S(g)
Determine the excess and limiting reactants and amount of
The limiting reactant is H2O (water), and the excess reactant is Al2S3 (aluminum sulfide). After the reaction, there will be 15.74 g of Al2S3 remaining as the excess reactant.
To determine the limiting and excess reactants, we need to compare the number of moles of each reactant with their stoichiometric coefficients in the balanced equation.
Mass of Al₂S₃ = 25.77 g
Mass of H₂O = 7.21 g
Molar mass of Al₂S₃ = 150.17 g/mol
Molar mass of H₂O = 18.02 g/mol
First, let's calculate the number of moles of each reactant:
Moles of Al₂S₃ = Mass of Al₂S₃ / Molar mass of Al₂S₃
= 25.77 g / 150.17 g/mol
= 0.1716 mol
Moles of H₂O = Mass of H₂O / Molar mass of H₂O
= 7.21 g / 18.02 g/mol
= 0.4007 mol
Next, we compare the mole ratios of Al₂S₃ and H₂O to their stoichiometric coefficients in the balanced equation:
From the balanced equation:
1 mol of Al₂S₃ reacts with 6 mol of H₂O
Moles of H₂O required to react with Al₂S₃ = 6 * Moles of Al₂S₃
= 6 * 0.1716 mol
= 1.0296 mol
Since we have 0.4007 mol of H₂O, which is less than the required 1.0296 mol, H₂O is the limiting reactant.
To determine the excess reactant and the amount remaining, we subtract the moles of the limiting reactant (H₂O) from the moles of the other reactant (Al₂S₃):
Excess moles of Al₂S₃ = Moles of Al₂S₃ - (Moles of H₂O / Stoichiometric coefficient of H₂O)
= 0.1716 mol - (0.4007 mol / 6)
= 0.1716 mol - 0.0668 mol
= 0.1048 mol
To calculate the amount of excess reactant remaining, we multiply the excess moles by the molar mass of Al₂S₃:
Mass of excess Al₂S₃ remaining = Excess moles of Al₂S₃ * Molar mass of Al₂S₃
= 0.1048 mol * 150.17 g/mol
= 15.74 g
Therefore, H₂O is the limiting reactant, and 15.74 g of Al₂S₃ will remain in excess after the reaction.
Learn more about limiting reactants at https://brainly.com/question/26905271
#SPJ11
The complete question is:
According to the following reaction,
Al₂S₃(s) + 6 H₂O (l) → 2 Al (OH)₃(s) + 3 H₂S(g)
Determine the excess and limiting reactants and the amount of excess reactant remaining when 25.77 20.00 g of Al₂S₃ and 7.21 2.00 g of H₂O are reacted. A few of the molar masses are as follows: Al₂S₃ = 150.17 g/mol, H₂O = 18.02 g/mol.