how fast is it moving when it reaches the top of its trajectory if the projectile is fired at a speed of 138 and an upward angle of 65 degrees?

The electric heater operates on 220 V and has a current of 12.8 A flowing through it. Ohm's law is used to find the resistance of the electric heater. The heater's resistance is 17.19 Ω.

Ohm's law states that the current flowing through a conductor between two points is directly proportional to the voltage across the two points. It can be mathematically represented as:

V = IR

Where, V is the voltage across the two points,

I is the current flowing through the conductor, and

R is the resistance of the conductor.

Rearranging the equation to solve for the resistance:

R = V/I

The voltage across the electric heater is 220 V, and the current flowing through it is 12.8 A.

Therefore, the resistance of the electric heater can be calculated as follows:

R = 220/12.8R = 17.19 Ω

Thus, the heater's resistance is 17.19 Ω.

To know more about Ohm's law:

https://brainly.com/question/12372387

#SPJ11

When the circuit is closed, the direction of the force exerted on the wire by the magnet is to the left.

A magnet placed near a wire creates a magnetic field. A wire carrying a current produces a magnetic field around it. These two fields interact, resulting in a force on the wire that is perpendicular to both the magnetic field of the magnet and the current in the wire. When the circuit is closed, a current is flowing through the wire. The current direction is shown in the picture below.

When a current-carrying wire is placed in a magnetic field, a force is exerted on the wire. The force is perpendicular to both the direction of the magnetic field and the direction of the current in the wire. The force is proportional to the strength of the magnetic field, the current in the wire, and the length of the wire within the magnetic field.

When the current flows, a magnetic field is produced around the wire that points upwards, as shown by the green arrows. When the magnetic field of the magnet is also taken into account, the direction of the force exerted on the wire is to the left, as shown by the blue arrow. Therefore, the answer is that when the circuit is closed, the direction of the force exerted on the wire by the magnet is to the left.

To know more about magnetic fields:

https://brainly.com/question/11514007

#SPJ11

The distance that a package will travel horizontally during its descent when a plane is flying at 800 miles per hour can be calculated using the following steps is 1600 miles.

Determine the time taken for the package to hit the ground. We know that when an object is dropped from a certain height, it falls under the influence of gravity.

The acceleration due to gravity is 9.8 m/s². The formula for the time taken for an object to fall can be given by:

t = √(2h/g)

where, t is the time taken for the object to fall is the height from which the object was dropped g is the acceleration due to gravity.

We know that the distance traveled by the package horizontally can be given by d = vt

where, d is the distance traveled horizontally by the package v is the velocity of the planet is the time taken for the package to hit the ground.

Thus, the distance is 1600 miles.

Read more about Distance here:

https://brainly.com/question/15172156

#SPJ11

The wavelengths (in nanometers) for the ultraviolet and visible ranges of the electromagnetic spectrum, in order of increasing energy (lower to higher).

The wavelengths (nm) for the ultraviolet and visible ranges of the electromagnetic spectrum are given below;

Wavelengths for the ultraviolet range of the electromagnetic spectrum: 100-400 nm

Wavelengths for the visible range of the electromagnetic spectrum: 400-700 nm

Wavelengths are measured in nanometers (nm). In order of increasing energy, the electromagnetic spectrum is arranged as follows:

Radio waves < microwaves < infrared radiation < visible light < ultraviolet radiation < X-rays < gamma rays.

Learn more about the Electromagnetic spectrum here:

https://brainly.com/question/23423065

#SPJ11

Yes, the wave base is the minimum depth of the water where wave-induced motion is absent and it is equivalent to one-half of the wavelength.

The wave base is the depth beneath the surface in which water waves' motion can no longer be detected. It's a fraction of the wave's wavelength. It is important to mention that the sea waves' speed is determined by the water's depth.

Wave-induced motionWave-induced motion is a movement caused by the waves rise and fall. The wave's energy is transferred to the floating object, causing it to rise and fall with the waves. This results in wave-induced motion.

Wave-induced motion can be a major issue for structures like offshore platforms and floating vessels.

For example, if the wavelength of a wave is 5 meters, the wave base is 2.5 meters.

Learn more about motion waves here:

https://brainly.com/question/30389794

#SPJ11

The minimum angle at which the box would begin to move is given by the equation $\mu_{s} = \tan{\theta}$,is 21.8°.

Let's consider the following diagram: In the above, m is the mass of the box, θ is the angle of the incline, N is the normal force, f is the force of friction, and mg is the gravitational force acting on the box in the downward direction.

The box will be at the threshold of sliding up or down the plane when the gravitational force acting down the plane is greater than the frictional force acting up the plane. Therefore, the minimum angle at which the box will start to move is:tanθ = μswhere μs is the coefficient of static friction=0.4 (Given). Thus,θ= tan-1 (0.4)θ = 21.8 degrees.

Therefore, the box will start to move when the angle of inclination of the plane is 21.8 degrees (minimum angle).

Read more about mass:

https://brainly.com/question/19385703:

#SPJ11

The magnitude of the force that the child exerts on the seat at the lowest point if his mass is 18.5 kg is 981 N.

To determine the magnitude of the force on the child, we must find the magnitude of the centripetal acceleration of the child at the low point first. We can use the equation:

[tex]a_{c}[/tex] = [tex]\frac{v^{2} }{r}[/tex]

where v = 9 m/s and r = 2 m

thus,

[tex]a_{c}[/tex] = [tex]\frac{9^{2} }{2}[/tex]

[tex]a_{c}[/tex] = 40.5 m/s²

And then, we find out the magnitude of the force that the child exerts on the seat at the lowest point if his mass is 18.5 kg.

∑[tex]f_{y}[/tex] = m × [tex]a_{c}[/tex]

[tex]f_{n}[/tex] - w = m × [tex]a_{c}[/tex]

[tex]f_{n}[/tex] = m × [tex]a_{c}[/tex] + w

[tex]f_{n}[/tex] = (18.5 × 40.5) + 18.5 (9.80)

[tex]f_{n}[/tex] = 981 N

Thus, the magnitude of the force that the child exerts on the seat at the lowest point if his mass is 18.5 kg in N is 981 N.

Your question is incomplete, but most probably your full question was

A mother pushes her child on a swing so that his speed is 9.00 m/s at the lowest point of his path. The swing is suspended 2.00 m above the child’s center of mass.

For more information about magnitude of the force refers to the link: https://brainly.com/question/30033702

#SPJ11

Answer :Gravity is the force that attracts two objects towards each other; when an object falls under the influence of gravity alone, it is said to be in free fall and will accelerate at a constant rate; as the velocity of a falling object increases, air resistance will begin to slow it down until it reaches terminal velocity; when an object is thrown or launched, it follows a curved path known as projectile motion which is influenced by both gravity and air resistance.

The electric force is the force that exists between two electrically charged objects or particles. The force is either repulsive or attractive depending on whether the objects have the same or opposite charges, respectively. Electric force can be calculated using Coulomb's law.

Alston answered that gravity is a force that is not fundamentally an electric force. This statement is correct because gravity is a fundamental force that acts between two massive objects. It does not depend on electric charges. The force of gravity is always attractive and can be calculated using Newton's law of universal gravitation.

The other fundamental forces in the universe are the strong nuclear force and the weak nuclear force. These forces are responsible for holding the nucleus of an atom together and are not electric in nature.    

Learn more about force at:

brainly.com/question/949418

#SPJ11  

The electric field of two point charges is inversely proportional to the cube of the distance between the two charges. This is because the electric field decreases exponentially with the increase in distance. Therefore, the equation for electric field varies as distance cubed in the denominator.

The electric field is an electric force that affects the space around electric charges. The cause of the electric field is the presence of positive and negative electric charges. The electric field can be described as lines of force or field lines.

The inverse square law states that the electric field at any point decreases as the square of the distance from the source. This means that the electric field decreases faster as the distance between two charges increases. Therefore, the equation for the electric field varies as distance cubed in the denominator to reflect this exponential decrease.

Learn more about inverse square law at https://brainly.com/question/30404562

#SPJ11

To change 500g of water at room temperature (20°C) to steam at 100°C, you will need to add 1128.500 kJ of heat. This is because water requires a certain amount of heat energy, called the 'latent heat of vaporization', to turn from a liquid to a gas.

Mass of water (m) = 500g

Initial temperature ([tex]T_i[/tex]) = 20°C

Final temperature ([tex]T_f[/tex]) = 100°C

The heat of vaporization ([tex]H_{vap}[/tex]) = 2260 J/g.

To calculate the amount of heat required to convert 500 g of water at room temperature to steam at 100°C, we will use the formula:

[tex]Q = m \times H_{vap}\\Q = 500 g \times 2260 J/g\\Q = 1128500 J[/tex]

Therefore, it would take 1130000 J of heat to change this water to steam at 100°C.

For further detail on latent heat of vaporization, click on the below link:

https://brainly.com/question/30762921

#SPJ11

The number of electrons per second striking the target is 0.00055 x 6.24 x 1018 = 3.44 x 10^15 electrons per second.

To calculate the number of electrons per second that strike a target when the electric current is 0.55 mA, we can use the equation: I = Q/t Where I is the electric current, Q is the charge, and t is the time. We can rearrange this equation to find Q as: Q = I

The charge of an electron is -1.6 x 10^-19 C. So, we can find the number of electrons that pass through a point by dividing the charge by the charge of one electron: n = Q/e Where n is the number of electrons and e is the charge of one electron. Substituting our values:n = 0.00055 / -1.6 x 10^-19n = -3.44 x 10^15.

This gives us a negative number, which means that the electrons are moving in the opposite direction to the conventional current. To find the absolute value of the number of electrons: n = 3.44 x 10^15.

Read more about the topic of electric current:

https://brainly.com/question/1100341

#SPJ11

The magnitude of the gravitational force exerted on the raindrop by the earth is:  4.86 x 10-5 N

and the magnitude of the gravitational force exerted on earth by the raindrop is: 4.86 x 10-5 N

(a) The gravitational force on a 5.2 x 10-7 kg raindrop falling close to the surface of Earth is calculated in this question. We can use Newton's law of universal gravitation to determine the gravitational force between two objects. The force between two objects is proportional to the product of their masses and inversely proportional to the square of the distance between them.

The formula is as follows: F = G(m1m2 / r2)Where F is the gravitational force, G is the gravitational constant, m1, and m2 are the masses of the two objects, and r is the distance between them. The mass of the Earth is approximately 5.97 x 1024 kg, and its radius is approximately 6.38 x 106 m.

The gravitational constant is 6.67 x 10-11 Nm2/kg2. If we substitute the given values in the formula, F = (6.67 x 10-11 Nm2/kg2) x (5.2 x 10-7 kg x 5.97 x 1024 kg) / (6.38 x 106 m)2 = 4.86 x 10-5 N

(b) We can use Newton's third law to determine the magnitude of the gravitational force exerted by the raindrop on Earth. According to the third law, for every action, there is an equal and opposite reaction.

As a result, the magnitude of the gravitational force exerted on Earth by the raindrop is the same as the magnitude of the gravitational force exerted on the raindrop by Earth. The magnitude of the gravitational force is 4.86 x 10-5 N, according to the previous calculation. So the gravitational force exerted on Earth by the raindrop is 4.86 x 10-5 N.

According to Newton's law of universal gravitation, the gravitational force between two objects is proportional to the product of their masses and inversely proportional to the square of the distance between them. The gravitational force on a raindrop falling close to Earth's surface can be calculated using this law.

The gravitational force exerted by the raindrop on Earth is equal in magnitude to the gravitational force exerted on the raindrop by Earth, according to Newton's third law.

To know more about gravitational force refer here:

https://brainly.com/question/12528243#

#SPJ11

The amount of work done is equal to 120 ft-lbs.

In the given scenario, we have a rope with a mass of 15 pounds hanging off the edge of a building. We need to lift the top 8 feet of the rope to the top of the building, and we want to calculate the work done in the process.

As we calculated previously, the weight of the rope is 147 pounds (15 pounds multiplied by the acceleration due to gravity, which is approximately 9.8 ft/s^2).

The distance over which the force is applied is 8 feet, as we need to lift the top 8 feet of the rope to the top of the building.

Using the formula for work:

Work = Force × Distance × Cosine of angle between Force and Displacement

we can plug in the values we have:

Work = 147 pounds × 8 feet × Cosine of angle between Force and Displacement

Now, since we are lifting the rope vertically upwards, the force and the displacement are in the same direction, which means the angle between them is 0 degrees. The cosine of 0 degrees is 1, so we can simplify the equation:

Work = 147 pounds × 8 feet × 1

Work = 1176 foot-pounds

So, the amount of work done to lift the top 8 feet of the rope to the top of the building is 1176 foot-pounds, not 120 foot-pounds as previously stated.

It's important to ensure that all the values, units, and calculations are accurate when calculating work, as it is a fundamental concept in physics and has practical applications in various fields, including engineering, mechanics, and energy calculations.

To know more about work done, refer here:

https://brainly.com/question/13662169

#SPJ11

A basketball whose mass is 0.540 kg falls from rest through a height of 5.65 m and then bounces back. on its way up it, passes by a height of 3.25 m with a speed of 2.35 m/s. The energy lost during the bounce is: 28.67 Joules

When a basketball is dropped from rest through a certain height and rebounds, it loses energy due to friction, deformation, and air resistance. In this situation, a basketball falls from rest from a height of 5.65 meters and rebounds, passing a height of 3.25 meters with a speed of 2.35 meters per second.

We know that work done W = mgh,

where, m = mass of the ball g = acceleration due to gravity h = height of the ball.

Energy lost during the bounce can be calculated by subtracting the kinetic energy of the ball after the bounce from its initial potential energy. When a ball falls from a certain height, it has initial potential energy due to its position in the earth's gravitational field.

When the ball rebounds, it has a certain kinetic energy that can be calculated using the conservation of energy equation. Therefore, the difference between the ball's initial potential energy and its rebound kinetic energy is the energy lost during the bounce.

Conservation of energy is applicable in this situation because the total energy before and after the bounce must remain constant if no external work is done on the ball. Therefore, we can apply the law of conservation of energy to this situation. The Kinetic Energy of the ball after rebounding can be calculated as:

K.E. = 1/2 mv²

Where, m = mass of the ball, v = velocity of the ball

The potential energy of the ball before rebounding can be calculated as: P.E. = mgh, Where, m = mass of the ball, g = acceleration due to gravity, h = height of the ball

Therefore, the initial potential energy of the ball can be calculated as: [tex]P.E. = 0.540 kg x 9.8 m/s² x 5.65 mP.E. = 30.2 Joules[/tex]

The ball rebounds and reaches a height of 3.25 m with a speed of 2.35 m/s.

Kinetic Energy of the ball after rebounding can be calculated as:

K.E. = 1/2 mv²

K.E. = 0.5 x 0.540 kg x (2.35 m/s)²

K.E. = 1.53 Joules.

Energy lost during the bounce = Initial Potential Energy - Rebound Kinetic Energy.

Energy lost during the bounce = 30.2 J - 1.53 J

Energy lost during the bounce = 28.67 J

Therefore, the energy lost during the bounce is 28.67 Joules.

To know more about energy refer here:

https://brainly.com/question/1932868#

#SPJ11

F1 will be in the direction of negative x-axis)F2 = kQ2q/(0.013 - x)² (as Q2 is negative, therefore F2 will be in the direction of positive x-axis)As F1 = F2, we can equate both equations,kQ1q/x² = kQ2q/(0.013 - x)². For an electron, the charge is negative, It will experience force in the direction of the positive x-axis. Therefore, the net force will not be zero if an electron is placed at x = 8.7 mm.

Given that A 2.4 n C charge is at the origin and a -4.0 n C charge is at 1.3 cm. At what x-coordinate could you place a proton so that it would experience no net force? Would the net force be zero for an electron placed at the same position? The given charges are,Q1 = 2.4 n C (positive charge) placed at the origin.Q2 = -4.0 nC (negative charge) placed at 1.3 cm (this can be converted to meters, which is 0.013m).Let's assume that a proton is placed at x distance from the origin at which it experiences no net force. If F1 is the force due to Q1 and F2 is the force due to Q2 then the net force on the proton will be, F net = F1 + F2

As we know that F1 and F2 are in opposite directions, the net force will be zero, therefore,F1 = F2If we apply Coulomb's law, then; F1 = kQ1q/x² (as both charges are positive, therefore F1 will be in the direction of negative x-axis)F2 = kQ2q/(0.013 - x)² (as Q2 is negative, therefore F2 will be in the direction of positive x-axis)As F1 = F2, we can equate both equations,kQ1q/x² = kQ2q/(0.013 - x)²Solving this equation for x, we get, x = 0.0087 m or 8.7 mm (approximately)Therefore, if a proton is placed at x = 8.7 mm, it will experience no net force. Would the net force be zero for an electron placed at the same position? For an electron, the charge is negative, therefore it will experience force in the direction of the positive x-axis. Therefore, the net force will not be zero if an electron is placed at x = 8.7 mm.

Learn more about X-coordinate

brainly.com/question/16634867

#SPJ11

The tension in the rope is 343.35 N.

To solve this question, we need to apply Newton's second law. In this scenario, the bucket is being lowered at a constant speed.

This means that the acceleration is zero. The forces acting on the bucket are gravity and tension.

Let's apply Newton's second law:ΣF = ma

Forces in the vertical direction:ΣF = 0

The forces acting on the bucket in the vertical direction are gravity (Fg) and tension (T).

Since the acceleration is zero, the net force must also be zero.

Therefore, the magnitude of the upward force (T) must be equal to the magnitude of the downward force (Fg).

Fg = mg

where m is the mass of the bucket and g is the acceleration due to gravity.

The force of tension can be calculated as follows:T = mg = (35.0 kg)(9.81 m/s²) = 343.35 N

The tension in the rope is 343.35 N.

To learn more about tension:

https://brainly.com/question/13397436#
#SPJ11

Answer:

Whether the object or fluid is moving, drag occurs as long as there is a difference in their velocities. Because it is resistant to motion, drag tends to slow down the object. An effective way to reduce it is to alter the shape of the object and make it streamline. Drag Force Examples of Drag Force

Explanation:

The minimum thickness of the film for constructive interference of reflected light would be t = 3*600/(2*1.4) = 850 nm.

The minimum thickness of a film required for constructive interference of reflected light can be calculated using the formula t = m*λ/(2*n),

where t is the minimum thickness of the film, m is the order of interference, λ is the wavelength of the light, and n is the index of refraction of the film.

For example, if the order of interference is 3, the wavelength of the light is 600 nm, and the index of refraction is 1.4,

the minimum thickness of the film for constructive interference of reflected light would be t = 3*600/(2*1.4) = 850 nm.

Constructive interference of reflected light occurs when the phase difference between the two waves is equal to an integral multiple of 2π.

This can be determined using the formula Δφ = (2π*m)/(λ*n), where Δφ is the phase difference, m is the order of interference, λ is the wavelength of the light, and n is the index of refraction of the film.

To achieve constructive interference, the minimum thickness of the film can be determined by ensuring that the phase difference is equal to an integral multiple of 2π.

The minimum thickness of a film required for constructive interference of reflected light can be calculated using the formula t = m*λ/(2*n),

where t is the minimum thickness of the film, m is the order of interference, λ is the wavelength of the light, and n is the index of refraction of the film.

Constructive interference can be achieved by ensuring that the phase difference between the two waves is equal to an integral multiple of 2π.

to know more about light refer here:

https://brainly.com/question/15200315#

#SPJ11

The work required to stretch the elastic spring an additional 6 cm is 2.16 J.

(a) To find the spring constant k, we can use the formula:

[tex]W = (1/2) k x^2[/tex]

where W is the work done, k is the spring constant, and x is the displacement from the equilibrium position. Rearranging this formula to solve for k, we get:

[tex]k = 2W / x^2[/tex]

Substituting the given values, we have:

[tex]k = 2(0.54 J) / (0.06 m)^2[/tex]

k = 300 N/m

Therefore, the spring constant of the elastic spring is 300 N/m.

(b) To find the work required to stretch the spring an additional 6 cm, we can use the same formula:

[tex]W = (1/2) k x^2[/tex]

where x is the additional displacement from the equilibrium position. The total displacement from the equilibrium position is 6 cm + 6 cm = 12 cm = 0.12 m.

Substituting the values, we have:

[tex]W = (1/2) (300 N/m) (0.12 m)^2W = 2.16 J[/tex]

To know more about " elastic springs. here

https://brainly.com/question/28997611

#SPJ4

Momentum is not always conserved in real-life situations because external forces can act on a system and change its momentum.

For example, when two cars collide, friction and air resistance can cause the momentum of the system to change. Similarly, when a ball is thrown in the air, gravity and air resistance act on it and cause its momentum to change. Other factors such as deformation, energy loss, and imperfect collisions can also cause momentum to be lost or gained. Therefore, while momentum is a useful concept in physics, it is important to consider the impact of external factors when analyzing real-world situations.

To know more about momentum, here

brainly.com/question/30677308
#SPJ4

The number of turns in the electromagnet is the strength of the magnetic field produced by the electromagnet:

The strength or intensity of а coils mаgnetic field depends on the following fаctors.

The explanation of the equations above, where:

The mаgnetic field strength of the electromаgnet аlso depends upon the type of core mаteriаl being used аs the mаin purpose of the core is to concentrаte the mаgnetic flux in а well defined аnd predictаble pаth.

For more information about the strength of the magnetic field refers to the link: https://brainly.com/question/28104888

#SPJ11

The waves will cancel each other out and no waves will remain. If two waves of the same frequency, but different amplitudes, interfere with each other, the resulting wave will have an amplitude equal to the sum of the two wave amplitudes.

Pulse waves are pressure waves that are created as the heart pumps blood throughout the body. They are detected through pulse points, such as on the wrists, neck, or temples. Pulse waves can be measured using a device called a pulse oximeter, which uses a sensor to detect the pressure of the pulse wave.

Pulse waves can provide information about a person’s heart rate and oxygen saturation levels.

Learn more about pulse waves here:

https://brainly.com/question/26701631
#SPJ1

Air masses contribute to the formation of air fronts because air masses are large bodies of air that have similar characteristics in terms of temperature, humidity, and stability.

When two air masses with different characteristics come into contact, they form a boundary known as an air front. The characteristics of the two air masses determine the type of air front that forms.

There are four types of air fronts: cold fronts, warm fronts, stationary fronts, and occluded fronts.

Air masses play a significant role in the formation of air fronts because they determine the characteristics of the air mass that will form at the boundary between the two air masses. This, in turn, determines the type of air front that will form and the type of weather that will result. For example, a cold, dry air mass coming into contact with a warm, moist air mass will likely result in a cold front and a period of heavy precipitation.

To learn more about Air masses, visit: https://brainly.com/question/19626802

#SPJ11

The reading on the scale is 838.29 N.

To determine the reading on the scale, use the following formula:

F = ma

where F is force, m is mass, and a is acceleration.

The weight of the individual can be determined using the formula:

W = mg

where W is weight, m is mass, and g is the acceleration due to gravity, which is 9.81 m/s².

The given acceleration is 0.47 m/s². The weight of the individual is W = mg,

where m = 799 N / 9.81 m/s² = 81.38 kg

W = 81.38 kg x 9.81 m/s² = 798.11 N.

To calculate the reading on the scale, we'll have to add the force the scale must apply to support the individual's weight to the weight of the person's mass multiplied by the acceleration:

Reading on the scale = 798.11 N + 81.38 kg x 0.47 m/s² = 838.29 N, rounded to three digits.

Therefore, the reading on the scale is 838.29 N to at least three digits.

Learn more about acceleration here: https://brainly.com/question/460763.

#SPJ11

A vector is a quantity that has a direction associated with it, and working with vectors involves identifying, representing, performing operations, resolving into components, and analyzing the vector.

A quantity that has a direction associated with it is called a vector. Vectors are used to describe physical quantities, such as velocity, force, and displacement, that have both magnitude and direction. To work with vectors, you can follow these steps:
1. Identify the vector quantity: Determine which physical quantity is being described and ensure it has both magnitude and direction.
2. Represent the vector: Vectors can be represented using arrows, where the length of the arrow represents the magnitude, and the direction of the arrow indicates the direction of the vector.
3. Perform vector operations: You may need to add, subtract, multiply, or divide vectors to solve problems. These operations involve working with both the magnitude and direction of the vectors.
4. Resolve the vector into components: Break the vector down into its horizontal and vertical components, which makes it easier to work with in calculations.
5. Analyze the vector: Use the components and other relevant information to solve the problem or analyze the situation.
For similar question on vector

https://brainly.com/question/28047791

#SPJ11

The primary mirror of an astronomical telescope is often shaped and polished to a parabolic shape because a parabolic shape allows for the mirror to collect the most amount of light and focus the parallel rays of light to a single point for better image clarity.

The reason that the primary mirror of an astronomical telescope is often shaped and polished to a parabolic shape is to reduce spherical aberration.

What is an astronomical telescope?An astronomical telescope is an optical instrument that aids in the observation of remote objects by collecting electromagnetic radiation such as visible light. It consists of two primary components: a primary mirror or lens that gathers and focuses light, and an eyepiece or camera that magnifies and projects the image formed by the primary.

A parabolic shape is a mirror or lens that has a curve that is more curved in the center than at the edges, and it is often used in astronomical telescopes to reduce spherical aberration. Spherical aberration is an optical defect that causes the image of a point source to become fuzzy and blurred. It occurs when the rays passing through the edges of a spherical lens or mirror become focused at a different distance than those passing through the center. This causes the image to be blurred around the edges, which makes it difficult to view small or distant objects. Parabolic mirrors are used to correct this problem because they are designed to focus all incoming light to a single point, resulting in a sharper and clearer image.

For more details about spherical aberration, click on below link:

https://brainly.com/question/13089079

#SPJ11

To determine the angular acceleration of the 4-kg slender bar released from rest in the position shown, we need to consider two cases:

(a) when the surface is rough and the bar does not slip, and

(b) when the surface is smooth.

(a) Rough surface (no slip):
1. Calculate the torque about the center of mass (CM). In this case, the only force causing the torque is gravity (mg), acting downward at the midpoint of the bar.
2. Calculate the moment of inertia (I) for the bar. Since it's a slender bar, I = (1/12) * mass * length^2.
3. Use Newton's second law for rotation:

Torque = I * angular acceleration (α). Solve for α.

(b) Smooth surface:
1. Calculate the torque about the point of contact (A) with the surface. In this case, the gravitational force (mg) acts downward at the midpoint of the bar and the frictional force (f) acts upward at point A.
2. Calculate the moment of inertia (I) for the bar about point A. Use the parallel axis theorem: I_A = I_CM + mass * distance^2.
3. Use Newton's second law for rotation:

Torque = I_A * angular acceleration (α). Solve for α.

By following these steps, you will be able to determine the angular acceleration of the 4-kg slender bar in both cases, when the surface is rough and when the surface is smooth.

To know more about Newton's Second Law here :

https://brainly.com/question/13447525

#SPJ11

The pressure exerted by the cylinder is 93,630 Pa.

Given data:

Mass of cylinder (m) = 75 kg

Length of cylinder (l) = 2.5 m

Radius of cylinder (r) = 5.0 cm = 0.05 m

The pressure exerted by the cylinder can be calculated using the formula:

P = F/A where P is the pressure, F is the force and A is the area of the surface over which the force is applied.

Area of the circular end of the cylinder, A = πr²= π(0.05)²= 0.00785 m²

Weight of cylinder: W = mg where g is the acceleration due to gravity (9.8 m/s²)W = 75 × 9.8W = 735 N

Now, the force exerted on the ground by the cylinder is equal to the weight of the cylinder, so, F = 735 N

Thus, the pressure exerted by the cylinder is, P = F/A= 735/0.00785= 93,630 Pa

Therefore, the pressure exerted by the cylinder is 93,630 Pa.

To know more about pressure click here:

https://brainly.com/question/29830939

#SPJ11

The tension, p, in the cable needed to give the 105-lb block a steady acceleration of 7 ft/sec2 up the incline is 164.375 lbs.

To solve this, use the equation for acceleration due to gravity:
a = g*sin(theta) - (T/m)
Where:
a = the steady acceleration of 7 ft/sec2
g = acceleration due to gravity (32.2 ft/sec2)
theta = the incline angle
T = the tension in the cable
m = the mass of the block (105 lbs)
Solving for T yields:
T = m*(a + g*sin(theta))
Inserting the given values yields:
T = 105 lbs * (7 ft/sec2 + 32.2 ft/sec2*sin(theta))
T = 164.375 lbs

Read more about the topic of tension

https://brainly.in/question/1958326

#SPJ11